Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
287 views

Baofeng UV B5 Programming Guide

This document provides step-by-step instructions for programming a Baofeng UV-B5 radio for communicating with a repeater at 147.080+ MHz with a 77.0 Hz tone, storing those settings in memory channel 57, and recalling the stored channel. It also gives instructions for programming the radio to operate simplex at 146.740 MHz and storing that in memory channel 8. The instructions include setting the frequency, offset, tone, and power level using the radio's menu system.

Uploaded by

Faizal Gerhani Putra
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
287 views

Baofeng UV B5 Programming Guide

This document provides step-by-step instructions for programming a Baofeng UV-B5 radio for communicating with a repeater at 147.080+ MHz with a 77.0 Hz tone, storing those settings in memory channel 57, and recalling the stored channel. It also gives instructions for programming the radio to operate simplex at 146.740 MHz and storing that in memory channel 8. The instructions include setting the frequency, offset, tone, and power level using the radio's menu system.

Uploaded by

Faizal Gerhani Putra
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Baofeng UV-B5 Step-by-Step Programming Guide

Also applies to UV-B6


Noji Ratzlaff
Set the radio to communicate with a repeater at 147.080+ MHz, 77.0 Hz
0. Turn on the radio and make sure it’s unlocked 5. Set the repeater offset

1. VM /SCAN (frequency mode) M ENU - •–(22) - AB5 - 00600 - AB5 - M ENU

2. Select the upper display 6. Set the repeater shift direction

AB5 M ENU - •–(21) - AB5 - + - AB5 - M ENU

3. Set the frequency 7. Set the transm it tone frequency

1-4-7-0-8-0 M ENU - •–(12) - AB5 - M ENU - •–(77.0) - AB5


- M ENU
4. Turn off the TDR
8. Set the transm it pow er level
M ENU - •–(10) - AB5 - OFF - AB5 - M ENU
M ENU - •–(04) - AB5 - HIGH - AB5 - M ENU

Your radio is now set to transm it as specified

Store the current repeater and tone settings in a memory channel


0. Follow the procedure above to set your radio
for the frequency of your choice

1. Store the frequency in channel 57

Press and hold VM /SCAN


•–(57) - AB5

(Note: if the channel number is blinking, there


is already a frequency stored there, and this
w ill overw rite it)

The frequency is now stored in radio memory

Recall a stored memory setting


1. Press VFO/M R (channel mode)

2. Press the up or dow n arrows or enter the


tw o-digit channel number (both digits)

0-6

The stored channel is now ready for use


Set the radio to communicate at 146.740 MHz simplex
0. Turn on the radio and make sure it’s unlocked 6. Remove the transm it tone frequency

1. VM /SCAN (frequency mode) M ENU - •–(12) - AB5 - M ENU (OFF) - AB5 -


M ENU
2. Select the upper display
7. Set the transm it pow er level
AB5
M ENU - •–(04) - AB5 - HIGH - AB5 - M ENU
3. Set the frequency
8. Store the frequency in channel 8
1-4-6-7-4-0
Press and hold VM /SCAN
4. Turn off the TDR •–(8) - AB5

M ENU - •–(10) - AB5 - OFF - AB5 - M ENU (Note: if the channel number is blinking, there
is already a frequency stored there, and this
5. Turn off the repeater shift direction w ill overw rite it)

M ENU - •–(21) - AB5 - 0 - AB5 - M ENU The simplex frequency is now stored in radio
memory

You might also like