NNSD 698 S

ORDER NO.
PHAMOS0801002C3
E1
Microwave Oven
NN-SD698S
NN-ST678S
NN-ST658W
RPH (LATIN AMERICA)
RUH (MEXICO)
© 2008 Panasonic Home Appliances Microwave

Oven (Shanghai) Co., Ltd. All rights reserved.
Unauthorized copying and distribution is a violation
of law.
Downloaded from www.Manualslib.com manuals search engine

NN-SD698S / NN-ST678S / NN-ST658W


CONTENTS
Page Page
1 SCHEMATIC DIAGRAM 5 5.5. Inverter power supply (U) 15
2 DESCRIPTION OF OPERATING SEQUENCE 6 5.6. Temperature thermistor 15
2.1. Variable power cooking control 6 6 MEASUREMENTS AND ADJUSTMENTS 16
2.2. Inverter power supply circuit 6 6.1. Adjustment of primary latch switch, secondary latch switch
2.3. Inverter defrost 6 and monitor interlock switch. 16
2.4. Sensor cooking 6 6.2. Measurement of microwave output 16
2.5. Sensor reheat 7 7 PROCEDURE FOR MEASURING MICROWAVE ENERGY
2.6. Steam sensor and digital programmer circuit 7 LEAKAGE 17
2.7. Thermistor 7 7.1. Equipment 17
3 CAUTIONS TO BE OBSERVED WHEN TROUBLESHOOTING 8 7.2. Procedure for measuring radiation leakage 17
3.1. Check the grounding 8 7.3. Record keeping and notification after measurement 17
3.2. Inverter warnings 8 7.4. At least once a year, have the radiation monitor checked
3.3. Part replacement. 9 for calibration by its manufacturer. 18
3.4. When the 20A fuse is blown due to the malfunction of the 8 TROUBLESHOOTING GUIDE 19
monitor interlock switch: 9 8.1. (Troubleshooting) Oven stops operation during cooking 19
3.5. Avoid inserting nails, wire etc. through any holes in the 8.2. (Troubleshooting) Other problems 20
unit during operation. 9 8.3. Troubleshooting of inverter circuit (U) and magnetron 21
3.6. Verification after repair 9 8.4. SIMPLE WAY OF H.V. INVERTER/MAGNETRON
3.7. Sharp edges 9 TROUBLESHOOTING 22
4 DISASSEMBLY AND PARTS REPLACEMENT PROCEDURE 10 8.5. H.V.INVERTER BOARD MAIN PARTS LIST
4.1. Magnetron 10 (F606Y8M00AP) 22
4.2. Digital programmer circuit (D.P.C) 10 8.6. How to check the semiconductors using an OHM meter 23
4.3. Low voltage transformer and/or power relays (RY1, RY2) 9 EXPLODED VIEW AND PARTS LIST 24
11 9.1. EXPLODED VIEW 24
4.4. Fan motor 11 9.2. PARTS LIST 25
4.5. Door assembly 11 9.3. WIRING MATERIALS 27
4.6. Turntable motor 12 9.4. DOOR ASSEMBLY 28
4.7. Steam sensor 12 9.5. ESCUTCHEON BASE ASSEMBLY 29
4.8. Inverter power supply 13 9.6. PACKING AND ACCESSORIES 32
5 COMPONENT TEST PROCEDURE 14 10 DIGITAL PROGRAMMER CIRCUIT 33
5.1. Primary, Secondary Latch Switch interlocks & Power 10.1. NN-SD698S 33
Relay RY1 14 10.2. NN-ST678S 35
5.2. Monitor Interlock Switch 14 10.3. NN-ST658W 37
5.3. Magnetron 14 10.4. PARTS LIST 39
5.4. key board membrane (Membrane switch assembly) 14

1 SCHEMATIC DIAGRAM

2 DESCRIPTION OF OPERATING SEQUENCE

2.1. Variable power cooking 2.3. Inverter defrost
control When the Auto Control feature is selected and the Start pad is
tapped:
High Voltage Inverter Power Supply (U) controls output power
by the signal from Digital Programmer Circuit (DPC). Power 1. The digital programer circuit determines the power level and
relay always stay on, but PWM (Pulse Width Modulation) signal cooking time to complete cooking and indicates the
controls microwave output power. operating state in the display window. Table shows the
corresponding cooking times for respective serving by
NOTE:
categories.
The ON/OFF time ratio does not correspond with the
Inverter Turbo Defrost
percentage of microwave power since approximately 2 SELECTED WEIGHT COOKING TIME
seconds are required for heating of magnetron 1.0 LB 5 min.00 sec.
filament.
Variable Power Cooking
2. When cooking time in the display window has elapsed, the
POWER SETTING OUTPUT MANUAL MICROWAVE oven turns off automatically by a control signal from the
POWER(%) DUTY digital programmer circuit.
APPROX. ON(SEC) OFF(SEC)
HIGH P10 100% 22 0 2.4. Sensor cooking
P9 90% 22 0
P8 80% 22 0 Auto sensor cooking without setting a power level or selecting
MEDIUM-HIGH P7 70% 22 0 a time. All that is necessary is to select an Auto Sensor
MEDIUM P6 60% 22 0 Program before starting to cook.
P5 50% 22 0 Understanding Auto Sensor Cooking
P4 40% 22 0
MEDIUM-LOW P3 30% 22 0 As the food cooks, a certain amount of steam is produced.
P2 20% 15 7 If the food is covered, this steam builds up and eventually
P1 10% 8 14 escapes from the container. In Auto Sensor Cooking, a
DEFROST P3 30% 22 0 carefully designed instrument, called the steam sensor
element, senses this escape of steam. Then, based upon
2.2. Inverter power supply circuit the Auto Sensor Program selected, the unit will
automatically determine the correct power level and the
The Inverter Power Supply circuit powered from the line proper length of time it will take to cook the food.
voltage, 120V 60Hz AC input supplies 4,000V DC to the
NOTE:
magnetron tube, and functions in place ofthe H.V. transformer,
the H.V. capacitor and H.V. diode. Auto Sensor Cooking is successful with the foods and
recipes found in the Auto Sensor Cooking Guide.
1. The AC input voltage 120V 60Hz is rectified to DC voltage
Because of the vast differences in food composition,
immediately.
items not mentioned in the Cooking Guide should be
2. DC voltage will be supplied to the switching devices called prepared in the microwave oven using power select
IGBT. These devices are switched ON-OFF by the 20 to 40 and time features. Please consult Variable Power
kHz PWM (pulse width modulation) signal from the Microwave Cookbook for procedures.
microcomputer in the DPC.
3. This drives the High voltage transformer to increase voltage
up to 2,000V AC.
4. Then the half-wave doubler voltage rectifier circuit,
consisting of the H.V. diodes and capacitors, generates the
necessary 4,000V DC needed for the magnetron.
5. Output power of the magnetron tube is always monitored by
the signal output from the current transformer built into the
inverter circuit.
6. This signal is fed back to the microcomputer in the DPC to
determine operating conditions and output necessary to
control PWM signal to the Inverter Power Supply for control
of the output power.

Explanation of the Auto Sensor Cooking process 2.5. Sensor reheat

1. During the first 10 second period there is no microwave
activity. When calculating the T2 time by using the Auto Sensor Reheat is a quick and easy way to reheat
formula below make sure this 10 seconds is subtracted refrigerated and room temperature foods.
from the T1 time. In other words, T1 time starts at the Simply press the reheat pad. There is no need to select power
end of the 10 second period. level and cooking time.
2. T1 time The total amount of time it takes themicrowave NOTE:
oven to switch to T2 time after the 10second period. The Auto Sensor Reheat process is same as Auto Sensor
3. T2 time When the steam escapes from the cooking Cooking process.
container placed in the oven, the steam sensor detects Category P1 P2 K Factor
it and the microprocessor calculates the balance of Power Power Standard
cooking time. This T2 time is then shown in the display Sensor Reheat HIGH MEDIUM 0.3
and begins counting down.
Balance of cooking time (T2 time) 2.6. Steam sensor and digital
The balance of cooking time which is called T2time, can programmer circuit
be calculated by the following formula.
In order to determine if the steam sensor function of the digital
T2 time (in sec.) = T1 time X K factor
programmer circuit is working, do the following test.
NOTE:
1. Place a water load (150 cc) in the oven.
Remember, the T1 time starts after the 10 second
2. Tap Sensor Reheat pad.
period. The coefficient K is programmed into the
microprocessor memory and they are listed in the 3. Tap Start pad.
following tables along with the P1 and P2 powers. 4. Steam Sensor detects steam about 1.5 to 4 minutes after
NOTE: the Start pad is tapped.
When "More" or "Less" pad is selected, the K factor 5. T1 time cooking automatically switches to remaining time
varies resulting in T2 time to be increased or decreased. for cooking (T2).
Example of calculating the T2 time 6. The remaining cooking time (T2) appears in display
window. If the following cooking time appears, Steam
Example 1: If the T1 time is measured to be 2 minutes and
Sensor function is normal.
40 seconds after the 10 second period, and the Auto
program selected is Oatmeal: T1 TIME T2 TIME (Remainingcooking time)
1 Min. 30 Sec. ~ 4 Min. 27 Sec. ~ 1Min.12 Sec.
T2 = T1 × K
= 2 min. and 40 sec. × 0.1
2.7. Thermistor
= 160sec. × 0.1
The thermistor which fixed on magnetron detects magnetron
= 16 sec.
temperature and make power down when the temperature
Category P1 P2 K Factor becomes abnormal high. A normal thermistor´s resistance
Power Power Standard
values for temperature ranges between 75-85 degree F is from
Oatmeal HIGH HIGH 0.1
37kΩ to 57kΩ.

3 CAUTIONS TO BE OBSERVED WHEN

TROUBLESHOOTING
Unlike many other appliances, the microwave oven is a high
voltage, high current device. It is free from danger in ordinary
use, though extreme care should be taken during repair.
CAUTION
Servicemen should remove their watches and rings
whenever working close to or replacing the magnetron.
3.1. Check the grounding

Do not operate on a two wire extension cord. The microwave
oven is designed to be grounded when used. It is imperative,
therefore, to ensure the appliance is properly grounded before
beginning repair work.
3.2. Inverter warnings

WARNING HIGH VOLTAGE AND HIGHTEMPERATURE
(HOT/LIVE) OF THE INVERTERPOWER SUPPLY (U)
The High Voltage Inverter Power Supply generates very
Grounding of the inverter circuit board
high voltage and current for the magnetron tube. Though it
is free from danger in ordinary use, extreme care should be WARNING DISCHARGE THE HIGH VOLATGE
taken during repair. CAPACITORS
The aluminum heat sink is also energized with high voltage For about 30 seconds after the oven is turned off, an
(HOT), do not touch when the AC input terminals are electric charge remains in the high voltage capacitors of the
energized. The power device Collector is directly connected Inverter Power Supply circuit board.
to the aluminum heat sink. When replacing or checking parts, remove the power plug
The aluminum heat sink may be HOT due to heat energy, from the outlet and short the inverter output terminal of the
therefore, extreme care should be taken during servicing. magnetron filament terminals to the chassis ground with an
insulated handle screwdriver to discharge. Please be sure
to contact the chassis ground side first and then short to the
output terminal.
H.V. Inverter warning

WARNING FOR INVERTER POWER SUPPLY (U)
GROUNDING
Check the High Voltage Inverter Power Supply circuit
grounding. The high voltage inverter power supply circuit
board must have a proper chassis ground. The inverter
grounding plate must be connected to the chassis. If the
inverter board is not grounded it will expose the user to very
high voltages and cause extreme DANGER! Be sure that
the inverter circuit is properly grounded via the inverter
grounding plate.

Discharging the high voltage capacitors 3.6. Verification after repair

WARNING
1. After repair or replacement of parts, make sure that the
There is high voltage present with high current capabilities
screws of the oven, etc. are neither loosen or missing.
in the circuits of the primary and secondary windings, choke
Microwave energy might leak if screws are not properly
coil and heat sinkof the inverter. It is extremely dangerous
tightened.
to work on or near these circuits with the oven energized.
DO NOT measure the voltage in the high voltage circuit 2. Make sure that all electrical connections are tight before
including the filament voltage of the magnetron. inserting the plug into the wall outlet.
WARNING 3. Check for microwave energy leakage. (Refer to procedure

for measuring microwave energy leakage).
Never touch any circuit wiring with your hand or with an
insulated tool during operation. CAUTION OF MICROWAVE RADIATION LEAKAGE
USE CAUTION NOT TO BECOME EXPOSED TO
3.3. Part replacement. RADIATION FROM THE MICROWAVE MAGNETRON OR
OTHER PARTS CONDUCTING MICROWAVE ENERGY.
When troubleshooting any part or component is to be replaced,
always ensure that the power cord is unplugged from the wall IMPORTANT NOTICE
outlet. 1. The following components have potentials above 2000V
while the appliance is operated.
3.4. When the 20A fuse is blown • Magnetron
due to the malfunction of the • High voltage transformer (Located on inverter (U))
monitor interlock switch: • High voltage diodes (Located on inverter (U))
WARNING • High voltage capacitors (Located on inverter (U))
When the 20A 120V fuse is blown due to the malfunction of Pay special attention to these areas.
the monitor interlock switch, replace all of the components 2. When the appliance is operated with the door hinges or
(primary latch switch, monitor interlock switch and power magnetron installed incorrectly, the microwave leakage
relay RY1). can exceed more than 5mW/cm 2. After repair or
1. This is mandatory. Refer to “measurements and exchange, it is very important to check if the magnetron
adjustments” for the location of these switches. and the door hinges are correctly installed.
2. When replacing the fuse, confirm that it has the 3.7. Sharp edges
appropriate rating for these models.
3. When replacing faulty switches, be sure the mounting CAUTION
tabs are not bent, broken or deficient in their ability to Please use caution when disassembling or reassembling
hold the switches. internal parts. Some exposed edges may be sharp to the
touch and can cause injury if not handled with care.
3.5. Avoid inserting nails, wire etc.
through any holes in the unit
during operation.
Never insert a wire, nail or any other metal object through the
lamp holes on the cavity or any holes or gaps, because such
objects may work as an antenna and cause microwave
leakage.

4 DISASSEMBLY AND PARTS REPLACEMENT

PROCEDURE
4.1. Magnetron 4.2. Digital programmer circuit
1. Discharge high voltage charge. (D.P.C)
2. Remove 1 screw holding air guide A on the oven cavity. CAUTION:
3. Remove 1 screw holding air guide A on the magnetron. Be sure to ground any static electric charge built up in
4. Remove 1 screw holding air guide B. your body before handling the DPC.
5. Remove 1 screw holding themistor. 1. Disconnect all connectors from D.P.C.
2. Remove 1 grounding screw.
3. Remove 1 screw holding escutcheon base and slide the
escutcheon base upward slightly.
4. Remove all screws holding D.P.C. board on escutcheon
base.
5. Separate D.P.C board from tabs on the escutcheon base
and remove D.P.C board.
To replace membrane key board
6. Use tools such as kinfe etc. to lift the edge of escutcheon
sheet and peel off escutcheon sheet & key board
membrane completely from escutcheon base.
NOTE:
1. The membrane key board is attached to the
escutcheon base with double faced adhesive tape.
Therefore, applying hot air such as using a hair
dryer is recommended for smoother removal.
2. When installing the new key board membrane, make
sure that the surface of escutcheon base is clean to
6. Disconnect 2 high voltage lead wires from magnetron prevent a malfunction or shorted contacts.
filament terminals.
7. Remove 4 screws holding the magnetron.
NOTE:
After replacement of the magnetron, tighten mounting
screws properly in an x pattern, making sure there is no
gap between the waveguide and the magnetron to
prevent microwave leakage.
CAUTION
When replacing the magnetron, be sure the antenna gasket is in
place.
10

4.3. Low voltage transformer 4.5. Door assembly

and/or power relays (RY1, 1. Remove door C from door E by carefully pulling outward,
RY2) starting from upper right hand corner using a flat blade
screwdriver.
CAUTION:
2. Separate door E from tabs on door A and remove door A.
Be sure to ground any static electric charge built up in
3. Open Door E at the opening angle of approximately
your body before handling the DPC.
10°(Note: The door cannot be removed if the opening
1. Replace D.P.C. board. angle is greater than 10°).
(A) Using solder wick or a desoldering tool and 30W 4. Remove the door E from its hinges by pushing the door E
soldering iron carefully remove all solder from the terminal upward and out.
pins of the low voltage transformer and/or power relays.
5. Remove door screen B from door A.
CAUTION:
6. Remove door key and door key spring.
Do not use a soldering iron or desoldering tool of
7. Replace other components.
more than 30 watts on D.P.C. contacts.
To re-install components:
(B) With all the terminal pins cleaned and separated from
D.P.C. contacts, remove the defective transformer/power 1. Place the door’s lower hinge pin into the bottom hinge
relays, Replace components making sure all terminal pins hole.
are inserted completely resolder all terminal contacts 2. Use your left index finger to support the door’s lower
carefully. hinge pin while guiding the door’s upper hinge pin into
the top hinge hole.
4.4. Fan motor 3. Lower your finger to seat the door onto the hinges.
1. Disconnect 2 lead wires from fan motor terminals. NOTE:
2. Remove 2 screws at location on oven attaching orifice Adjust so that the upper portion of the door will
assembly. touch firmly to the oven cavity front plate, without
3. Remove orifice assembly from oven assembly. pushing the door. If the door assembly is not
mounted properly, microwave power may leak from
4. Remove fan blade from the fan motor shaft by pulling it
the clearance between the door and oven.
straight out.
NOTE:
5. Remove 2 screws holding fan motor to orifice.
Always perform the microwave leakage
measurement test after installation and adjustment
of door assembly.
11

4.6. Turntable motor 4.7. Steam sensor

1. Remove the motor cover by breaking off at the 8 spots 1. Disconnect connector CN2 from digital programmer circuit
indicated by arrows with a cutter or the like. board.
2. Disengage catch hooks on sensor cover C from orifice.
NOTE:
After removing the motor cover, be sure that cut
portions are properly trimmed or bent to the inside
so that no sharp edges will be exposed to outside. 3. Remove steam sensor from orifice.
2. Disconnect 2 lead wires connected to the turntable motor. NOTE:
3. Remove the turntable motor by removing screw. When installing the steam sensor, make sure that
the direction of steam sensor is as shown in figure.
NOTE:
After reinstalling the new turntable motor and
reconnecting the 2 lead wires, reinstall the motor
cover by rotating it around 180, tucking the 2 tabs
under the base in the 2 provided slots, then screw
the single tab to the base using a 4mm × 6mm
screw.
12

4.8. Inverter power supply 6. Press 1 encircled locking tab and then slide 4 locking tabs
of Inverter bracket at the bottom of the base in direction of
CAUTIONS arrows.
1. Always leave the grounding plate in place.
2. Always securely tighten the ground screw through the bottom of the
chassis (base).
3. Securely connect 3 lead wire connectors.
4. Make sure the heat sink has enough space (gap) from the oven.
Take special care not to dress any lead wire over the aluminum heat
sink because it is hot.
1. Discharge high voltage charge.

2. Remove the H.V.lead wire from magnetron terminals.
3. Disconnect 2 connectors from CN701 & CN702 on
H.V.Inverter(U).
4. Remove 1 screw holding grounding plate to the base.
7. Remove 1 screw holding H.V.Inverter to Inverter bracket.
5. Bend back 1 locking metal tab on the base.
8. Remove 1 screw holding grounding plate to H.V. Inverter.
9. Seperate H.V. Inverter from Inverter bracket by freeing 3

catch hooks on the Inverter bracket.
13

5 COMPONENT TEST PROCEDURE

WARNING 5.3. Magnetron
1. High voltage is present at the output terminals of the High Voltage
Inverter (U) including aluminum heat sink during any cook cycle. Continuity checks can only indicate an open filament or a
2. It is neither necessary nor advisable to attempt measurement of the shorted magnetron. To diagnose for an open filament or
high voltage.
3. Before touching any oven components, or wiring, always unplug shorted magnetron.
the power cord and discharge the high voltage capacitors (see page 1. Isolate magnetron from the circuit by disconnecting the
8).
leads.
2. A continuity check across magnetron filament terminals
5.1. Primary, Secondary Latch
should indicate one ohm or less.
Switch interlocks & Power 3. A continuity check between each filament terminal and
Relay RY1 magnetron case should read open.
1. Unplug lead connectors to Power Relay RY1 and verify

open circuit of the Power Relay RY1 1-2 terminals.
2. Unplug lead connectors to Primary Latch Switch and
Secondary Latch Switch.
3. Test the continuity of switches at door opened and closed
positions with ohm meter (low scale).
Normal continuity readings should be as follows.
Door Closed Door Opened
Primary Latch Switch 0Ω (Close) Ω(Open)
Secondary Latch Switch 0Ω (Close) Ω(Open)
Power Relay RY1 Ω (Open) Ω(Open)
5.2. Monitor Interlock Switch

1. Unplug lead wires from Inverter Power Supply (U) primary
terminals.
2. Connect test probes of ohm meter to the disconnected 5.4. key board membrane
leads that were connected to Inverter Power Supply (U). (Membrane switch assembly)
3. Test the continuity of Monitor Interlock Switch with door
opened and closed positions using lowest scale of the ohm Check continuity between switch terminals, by tapping an
meter. appropriate pad on the key board. The contacts assignment of
the respective pads on the key board is as shown in digital
Normal continuity readings should be as follows.
programmer circuit.
Door Opened Door Closed
0Ω (Close) Ω (Open)
14

5.5. Inverter power supply (U)

5. Program oven at High power for 1 minute and press [Start]
DO NOT try to REPAIR H.V. Inverter power supply (U). pad.
Replace complete H.V. Inverter(U) Unit.
a. After approximately 3 seconds, oven stops operating.
b. During oven operation, the input current is
approximately 0.4A.
INPUT CURRENT FAILURE CODE
Unplug CN701 0.4A Oven stops in 3
seconds after started.
If both a and b check OK, the Inverter Power Supply (U) can be
determined to be OK.
5.6. Temperature thermistor

These sensor monitors the heat produced by the heater circuit
and maintains the magnetron temperature which user had
selected. Normal room temperature 10°C to 30°C, the reading
across the temperature thermistor should be as follows.
TEMP MAGNETRON THERMISTOR
100°C 30-60KΩ
25°C 700K-1.5MΩ
If the resistance reading is out of the range stated here, the

WARNING: HIGH VOLTAGE
thermistor is detective and must be replaced.
Test if failure codes H95, H97 or H98 appear when performing
the following procedure. It is recommended to use an AC line
input current ammeter for testing.
Test 1
1. With the oven unit’s AC power supply cord is unplugged
from the wall outlet, unplug the 2 pin H.V. connector CN703
from the magnetron tube.
2. Place 1 liter of water load into oven cavity.
3. Plug in the oven’s AC power supply cord into outlet.
4. Program DPC.
a. Press Timer/Clock pad twice.
b. Press Start pad once.
c. Press Power Level pad once.
5. Program oven at High power for 1 minute and press [Start]
pad.
a. After approximately 37 seconds, oven stops operating.
b. During oven operation, the input current is
approximately 0.5 to 1A. If both a and b are OK,
proceed to test 2.
INPUT CURRENT FAILURE CODE
Unplug CN703 0.5 to 1A Oven stops in 37
seconds after started.
Test 2
Continued from Test 1
1. Unplug the oven’s AC power supply cord from outlet.
2. Unplug 3 pin connector CN701. CN703 remains unplugged.
3. Plug in the oven’s AC power supply cord into outlet.
4. Program DPC.
a. Press Timer/Clock pad twice.
b. Press Start pad once.
c. Press Power Level pad once.
15

6 MEASUREMENTS AND ADJUSTMENTS
6.1. Adjustment of primary latch

switch, secondary latch switch
and monitor interlock switch.
1. Mount the Primary latch switch, the Secondary latch switch
and the Monitor interlock switch to the door hook assembly
as shown in illustration.
NOTE:
No specific individual adjustments during 6.2. Measurement of microwave
installation of the Primary latch switch, Secondary output
latch switch or Monitor interlock switch to the door
hook are required. The output power of the magnetron can be determined by
performing IEC standard test procedures. However,due to the
2. When mounting the door hook assembly to the oven
complexity of IEC test procedures, it is recommended to test
assembly, adjust the door hook assembly by moving it in
the magnetron using the simple method outlined below.
the direction of the arrows in the illustration so that the oven
door will not have any play in it. Check for play in the door Necessary Equipment:
by pulling the door assembly. Make sure that the latch keys *1 liter beaker *Glass thermometer
move smoothly after adjustment is completed. Completely *Wrist watch or stopwatch
tighten the screws holding the door hook assembly to the NOTE:
oven assembly.
Check the line voltage under load.Low voltage will
3. Reconnect the monitor interlock switch and check the lower the magnetron output. Take the temperature
continuity of the monitor circuit and all latch switches again readings and heating time as accurately as possible.
by following the component test procedures.
1. Fill the beaker with exactly one liter of tap water.Stir the
water using the thermometer and record the water’s
temperature. (recorded as T1).
2. Place the beaker on the center of glass tray.
Set the oven for High power and heat it for exactly one
minute.
3. Stir the water again and read the temperature of the water.
(recorded as T2).
4. The normal temperature rise at High power level for each
model is as shown in table.
TABLE (1L-1min. test)
RATED OUTPUT TEMPERATURE RISE
1200W Min. 18.5°F(10.3°C)
1300W Min. 19.8°F(11.1°C)
16

7 PROCEDURE FOR MEASURING MICROWAVE ENERGY

LEAKAGE
7.2.1. Measurement with the outer panel
removed.
Whenever you replace the magnetron, measure for radiation
leakage before the outer panel is installed and after all
necessary components are replaced or adjusted. Special care
should be taken in measuring around the magnetron.
7.1. Equipment
• Electromagnatic radiation monitor
• Glass thermometer 212°F or 100°C 7.2.2. Measurements with a fully
• 600cc glass beaker assembled oven.
After all components, including outer panel are fully assembled,
7.2. Procedure for measuring measure for radiation leakage around the door periphery, the
radiation leakage door viewing window, the exhaust opening, control panel and
air inlet openings.
Note before measuring:
• Do not exceed meter full scale deflection. Leakage monitor 7.3. Record keeping and
should initially be set to the highest scale.
notification after measurement
• To prevent false readings, the test probe should be held by
the grip portion of the handle only and moved along the • After any adjustment or repair to a microwave oven, a
shaded area in Figure no faster than 1 inch/sec leakage reading must be taken. Record this leakage
(2.5cm/sec). reading on the repair ticket even if it is zero.
• Leakage with the outer panel removed: less than 5mW/cm 2. A copy of this repair ticket and the microwave leakage
reading should be kept by repair facility.
• Leakage for a fully assembled oven with door normally
closed: less than 2mW/cm 2. • Should the radiation leakage be more than 2 mW/cm 2 after
determining that all parts are in good condition, functioning
• Leakage for a fully assembled oven [Before the latch switch
properly, and genuine replacement parts as listed in this
(primary) is interrupted] while pulling the door: less than
manual have been used.
2mW/cm 2.
1. Pour 275 ± 15cc (9ozss± 1/2oz) of 20°C ± 5°C (68° ± 9°F)
water in a beaker which is graduated to 600cc, and place in
the center of the oven.
2. Set the radiation monitor to 2450MHz and use it following
the manufacturer´s recommended test procedure to assure
correct results.
3. When measuring the leakage, always use the 2 inch (5cm)
spacer supplied with the probe.
4. Tap the start button or set the timer and with the magnetron
oscillating, measure the leakage by holding the probe
perpendicular to the surface being measured.
17

7.4. At least once a year, have the

radiation monitor checked for
calibration by its
manufacturer.
18

8 TROUBLESHOOTING GUIDE
DANGER: HIGH VOLTAGES
1. DO NOT RE-ADJUST PRESET CONTROL on the H.V.Inverter (U). It is very dangerous to repair or adjust without proper test equipment
because this circuit generates very large current and high voltage. Operating a misaligned inverter circuit is dangerous.
2. Ensure proper grounding before troubleshooting.
3. Be careful of the high voltage circuitry, taking necessary precautions when troubleshooting.
4. Discharge high voltage remaining in the H.V.Inverter (U).
5. When checking the continuity of the switches or the H.V.Inverter, disconnect one lead wire from these parts and then check continuity with the
AC plug removed. Doing otherwise may result in a false reading or damage to your meter. When disconnecting a plastic connector from a
terminal, you must hold the plastic connector instead of the lead wire and then disconnect it, otherwise lead wire may be damaged or the
connector cannot be removed.
6. Do not touch any parts of the circuitry on the digital programmer circuit, since static electric discharge may damage this control panel. Always
touch ground while working on this panel to discharge any static charge in your body.
7. 120V AC is present on the digital programmer circuit (Terminals of power relay’s and primary circuit of Digital Programmer Circuit). When
troubleshooting, be cautious of possible electrical shock hazard.
Before troubleshooting, operate the microwave oven following the correct operating procedures in the instruction manual in order
to find the exact cause of any trouble, since operator error may be mistaken for the oven’s malfunction.
8.1. (Troubleshooting) Oven stops operation during cooking

SYMPTOM CAUSE CORRECTIONS
1. Oven stops in 3 seconds after No 120V AC is supplied to H.V.Inverter (U) CN702 1. Latch Switch
pressing [Start] pad terminals 2. Power relay RY1
3. Loose lead wire connector CN701, CN702
4. H.V. Inverter (U)
Oven stops in 37 seconds after H.V.Inverter (U) operates by the control signals 1. Magnetron
pressing [Start] pad from DPC but magnetron is not oscillating 2. Loose lead wire connector CN703
3. H.V. Inverter (U)
Oven stops in 10 seconds after Steam sensor circuit is not functioning 1. Steam sensor
pressing [Start] pad 2. DPC
(Auto sensor cooking) 3. Open or loose wiring of sensor terminal
from connector CN2 on DPC
2. No display and no operation at all. Most probably loose connection of connectors, or 1. Allign door, Door Latch Switches
Fuse is blown. door latch mechanism is not adjusted properly 2. Loose wiring connectors
19

8.2. (Troubleshooting) Other problems

SYMPTOM CAUSE CORRECTIONS
1. Oven is dead. 1. Open or loose lead wire harness
Fuse is OK. 2. Open thermal cutout / thermistor Check thermal cutout is defective.
No display and no operation at all. 3. Open low voltage transformer
4. Defective DPC
2. No display and no operation at all. 1. Shorted lead wire harness Check adjustment of primary, secondary latch
Fuse is blown. 2. Defective primary latch switch (NOTE 1) switch and monitor interlock switch including
3. Defective monitor interlock switch (NOTE 1) door.
4. Defective Inverter Power Supply (U)
NOTE 1:
All of these switches must be replaced at the same time.
Check continuity of power relay RY1 contacts (between 1 and 2) and if it has continuity, replace
power relay RY1 also.
3. Oven does not accept key input 1. Key input is not in proper sequence Refer to operation procedure.
(Program) 2. Open or loose connection of membrane key
pad to DPC (Flat cable)
3. Shorted or open membrane key board
4. Defective DPC Refer to DPC troubleshooting.
4. Fan motor turns on when oven is 1. Misadjustment or loose wiring of secondary Adjust door and latch switches.
plugged in with door closed. latch switch
2. Defective secondary latch switch
3. Door switch CN3
5. Timer starts count down but no 1. Off-alignment of primary latch switch Adjust door and latch switches.
microwave oscillation. 2. Open or loose connection of high voltage
(No heat while oven lamp and fan circuit especially magnetron filament circuit
motor turn on) NOTE:
Large contact resistance will cause lower
magnetron filament voltage and cause
magnetron to have lower output and/or be
intermittent.
3. Defective high voltage component Check high voltage component according to
H.V. Inverter Power Supply (U) component test procedure and replace if it is
Magnetron defective.
4. Open or loose wiring of power relay RY1
5. Defective primary latch switch
6. Defective DPC or power relay RY1 Refer to DPC troubleshooting
6. Oven can program but timer does not 1. Open or loose wiring of secondary latch switch
start countdown. 2. Off-alignment of secondary latch switch
3. Defective secondary latch switch
7. Microwave output is low. Oven takes 1. Decrease in power source voltage Consult electrician
longer time to cook food. 2. Open or loose wiring of magnetron filament
circuit.(Intermittent oscillation)
3. Aging change of magnetron
8. Fan motor turns on and turntable 1. Low voltage transformer on DPC.
motor rotates when door is opened.
9. Oven does not operate and return to 1. Defective DPC Check grounding connector on escutcheon
plugged in mode as soon as [Start] base.
pad is pressed.
10. Loud buzzing noise can be heard. 1. Loose fan and fan motor
11. Turntable motor does not rotate. 1. Open or loose wiring of turntable motor
2. Defective turntable motor
12. Oven stops operation during cooking. 1. Open or loose wiring of primary and Adjust door and latch switches.
secondary latch switch
2. Operation of thermal cutout
20

8.3. Troubleshooting of inverter circuit (U) and magnetron

This oven is programmed with a self diagnostics failure code system which will help for troubleshooting. H95, H97, H98 and H99
are the provided failure codes to indicate magnetron and inverter circuit problem areas. This section explains failure codes of H95,
H97, H98 and H99. First, you must program the DPC into TEST MODE, press Timer/Clock pad twice → Press Start pad once
→ press Power Level pad once. Program unit for operation. H95, H97, H98, H99 appears in display window a short time after
[Start] pad is pressed and there is no microwave oscillation.
Alternate way to troubleshoot oven with AC Ampere meter used
H95, H97, H98, H99 appears in display window a short time after [Start] pad is pressed and no microwave oscillation with AC
Ampere meter used for troubleshooting.
21

8.4. SIMPLE WAY OF H.V. INVERTER/MAGNETRON TROUBLESHOOTING

Purpose:
Simple way (3/37 seconds rule) of identifying whether it’s Magnetron, Inverter or others.
Set-up:
The unit under question is connected through the Ammeter as shown below.
Procedure:
Follow the matrix table below to identify the problem source.
Note:
Do not replace both Inverter board and Magnetron simultaneously and automatically without going through this
procedure.
Power will: Ammeter reading is: To do: Remedy:
Shut off in 37 seconds 1. Between 0.5A and 1.0A. Check and repair open magnetron circuit Open magnetron wiring between Inverter
after “Start”. and magnetron terminal.
2. Between 1.0A and 2.0A. Check continuity of D702 in Inverter PCB.
1. D702 shorted Replace H.V.Inverter(F606Y8M00AP)

2. D702 is OK Replace magnetron
Shut off in 3 seconds 1. Less than 0.5A Check open circuit: Latch Switch, DPC, Replace defective component(s), or
after “Start” Power Relay and CN701 correct switch, cables and connectors.
8.5. H.V.INVERTER BOARD MAIN PARTS LIST (F606Y8M00AP)

Ref. No. Part No. Part Name & Description Pcs/Set Remarks
DB701 B0FBBS000001 BRIDGE DIODE 1 20A, 600V
L701 F50206G00AP CHOKE COIL 1
Q701 B1JAGV000015 TRANSISTOR SI 1 1000V
T701 A609A8M00AP H.V. TRANSFORMER 1 (INCLUDING D701,D702,C706,C707)
C701 ECWF5284N300 CAPACITOR 1 0.28µF/500V
C702 ECWF2455N644 CAPACITOR 1 4.5µF/250V
22

8.6. How to check the semiconductors using an OHM meter
23

9 EXPLODED VIEW AND PARTS LIST

9.1. EXPLODED VIEW
24

9.2. PARTS LIST

NOTE:
1. When ordering replacement part(s), please use part number(s) shown in this part list.
Do not use description of the part.
2. Important safety notice:
Components identified by mark have special characteristics important for safety.
When replacing any of these components, use only manufacture’s specified parts.
1 F00069660AP CAUTION LABEL 1
2 F00078X00SRP NAME PLATE 1 SD698S RPH
2 F00078X00SRU NAME PLATE 1 SD698S RUH
2 F00078V60SRP NAME PLATE 1 ST678S RPH
2 F00078V60SRU NAME PLATE 1 ST678S RUH
2 F00078V70HRP NAME PLATE 1 ST658W RPH
2 F00078V70HRU NAME PLATE 1 ST658W RUH
3 F00338F00RP FUSE LABEL 1
4 F10016K10APG BASE 1
5 F10084T00AP RUBBER FOOT 4
6 F110D5Y00SAP CABINET BODY(U) 1 SD698S

6 F110D5Y30SAP CABINET BODY(U) 1 ST678S
6 F110D5Y30HAP CABINET BODY(U) 1 ST658W
7 F200A8F00AP OVEN(U) 1 SD698S
7 F200A8F40AP OVEN(U) 1 ST678S,ST658W
8 F20555L00AP COVER 1
9 F21315Y00AP PULLY SHAFT 1
10 F2177-F80 WASHER 1
11 F290D9330AP ROLLER RING(U) 1

12 F30206G30AP DOOR HOOK 1 SD698S,ST678S
12 F30206K50AP DOOR HOOK 1 ST658W
13 F3097-5L00 LATCH SPRING 1 ST658W
14 F31366G30AP HOOK LEVER A 1 SD698S,ST678S
14 F31366K50AP HOOK LEVER A 1 ST658W
15 F31376G30AP HOOK LEVER B 1 SD698S,ST678S
15 F31376K50AP HOOK LEVER B 1 ST658W
16 F31386G30AP HOOK LEVER C 1 SD698S,ST678S

16 F31386K50AP HOOK LEVER C 1 ST658W
17 F400A5Y00AP FAN MOTOR 1 AC120V,SINGLE PHASE,60Hz
18 F40084T00AP FAN BLADE 1
19 F40257D00APG AIR GUIDE A 1
20 F41445Y00AP ORIFICE 1
21 J607S4T00AP STEAM SENSOR 1 SD698S

22 F64508660AP SENSOR COVER B 1 SD698S
24 F65434W00AP SENSOR COVER C 1 SD698S
25 F612E5U40AP INCANDESCENT LAMP (U) 1
26 J61415G10XN MICRO SWITCH 1 (PRIMARY LATCH SWITCH) (V-15G-3C25)

27 J61414T00AP MICRO SWITCH 1 (SECONDARY LATCH SWITCH) (D3V-16G-3C25)
28 F61456N60AP THERMAL CUTOUT 1
30 F61785U30XN MICRO SWITCH 1 (MONITOR INTERLOCK SWITCH) (D3V-1G-2C25)
31 F606Y8M00AP H.V.INVERTER (U) 1

32 2M261-M32KLP MAGNETRON 1
33 F62308F20AP FUSE 1
35 F66626K50AP GROUNDING PLATE 1
36 F63265G60AP TURNTABLE MOTOR 1

37 F900C4T00AP AC CORD W/PLUG 1
38 F62315G10XN FUSE HOLDER 1
39 XTWFL4+12T SCREW 4 FOR MAGNETRON
40 XTTFL4+6BN SCREW 1 FOR COVER
42 XTCAFA4+12AFM SCREW 1 FOR CABINET BODY SIDE (SD698S)

42 XTCAFA4+12AFS SCREW 1 FOR CABINET BODY SIDE (ST678S)
42 XTCAFA4+12AFW SCREW 1 FOR CABINET BODY SIDE (ST658W)
43 XTTBFE4T12A0 SCREW 4 FOR CABINET BODY
25

45 F65856K50AP INVERTER BRACKET 1
46 F03347D00RP MENU LABEL 1 SD698S

46 F03347G50RP MENU LABEL 1 ST678S,ST658W
48 F40264T60APG AIR GUIDE B 1

52 F00066G00RP CAUTION LABEL 1 SD698S RPH,ST678S RPH
26

9.3. WIRING MATERIALS
W1 F030A7D00RP LEAD WIRE HARNESS 1
W2 F030E5L00AP H.V.LEAD WIRE 1
W3 F03537D00AP LEAD WIRE HARNESS U 1 (INCLUDING THERMISTOR)
27

9.4. DOOR ASSEMBLY
D1 F30186P40AG DOOR KEY A 1 SD698S,ST678S
D1 F30184Y30XN DOOR KEY A 1 ST658W
D2 F301A8X00SCP DOOR A (U) 1 SD698S
D2 F301A8M00SAP DOOR A (U) 1 ST678S
D3 F302K5L00AP DOOR E (U) 1
D4 F30215G10XN DOOR KEY SPRING 1
D5 F30854T00AP DOOR C 1
D6 F31454T00AP DOOR SCREEN A 1

D7 F31468F50HCP DOOR SCREEN B 1 ST658W
D8 F30016K50HAP DOOR A 1 ST658W
D10 F02459660AP DHHS LABEL 1 SD698S,ST678S
28

9.5. ESCUTCHEON BASE ASSEMBLY

9.5.1. NN-SD698S
E1 F603L8X00RP D.P.CIRCUIT (AU) 1 SD698S
E2 F603Y8X00RP D.P.CIRCUIT (DU) 1 SD698S
E3 F800L8X00SRP ESCUTCHEON BASE (U) 1 SD698S
E4 F66164W20AP FLAT CABLE 1 SD698S
E5 F82988X00SAP BUTTON 1 SD698S
E6 F80725Y00SAP DOOR OPENING BUTTON (U) 1 SD698S
E7 F82566K10AP DOOR OPENING LEVER 1 SD698S
E8 F80375K00AP COOK BUTTON SPRING 1 SD699S
E10 F90095X00AP GROUNDING PANEL 1 SD698S
E11 F83928P00KAP DIAL 1 SD698S
29

9.5.2. NN-ST678S
E21 F603L8V60RP D.P.CIRCUIT (AU) 1 ST678S
E23 F800L8V60SRP ESCUTCHEON BASE (U) 1 ST678S
E26 F80725Y00SAP DOOR OPENING BUTTON (U) 1 ST678S
E27 F82565Y00AP DOOR OPENING LEVER 1 ST678S
E28 F80375K00AP COOK BUTTON SPRING 1 ST678S
E29 F630Y8V60BRP MEMBRANE SWITCH (U) 1 ST678S
E30 F90095X00AP GROUNDING PANEL 1 ST678S
30

9.5.3. NN-ST658W
E41 F603L7G50RP D.P.CIRCUIT (AU) 1 ST658W
E43 F80346K50HAP ESCUTCHEON BASE 1 ST658W
E49 F630Y8V70HRP MEMBRANE SWITCH (U) 1 ST658W
E50 L5AAAEC00056 DISPLAY 1 ST658W
E51 F66175L00AP DISPLAY TUBE COVER 1 ST658W
E52 F67005U40XN RUBBER CONNECTOR 1 ST658W
31

9.6. PACKING AND ACCESSORIES
P1 F00038X00RP INSTRUCTION MANUAL 1 SD698S
P1 F00038V60RP INSTRUCTION MANUAL 1 ST678S,ST658W
P2 F01028X00SRP PACKING CASE,PAPER 1 SD698S RPH
P2 F01028V60SRP PACKING CASE,PAPER 1 ST678S RPH
P2 F01028V70HRP PACKING CASE,PAPER 1 ST658W RPH
P3 F01046K50AP UPPER FILLER 1
P4 F01055L00AP LOWER FILLER 1
P5 F01067F00AP P.E.BAG 1 SD698S,ST678S
P5 F01068100XN P.E.BAG 1 ST658W
P6 F01078J00XN DOOR SHEET 1

P8 F06014T00AP COOKING TRAY 1
P9 F01924T00AP SHEET 1
P10 F00065G40AP CAUTION LABEL 1
P12 F00166H70RP NOTICE 1 SD698S,ST678S
32

10 DIGITAL PROGRAMMER CIRCUIT

10.1. NN-SD698S
33

34

10.2. NN-ST678S
35

36

10.3. NN-ST658W
37

38

10.4. PARTS LIST

10.4.1. NN-SD698S
BZ310 L0DDEA000014 BUZZER 1 2.0KHz
C10 AECETK1V471B AL CHEM CAPACITOR 1 470µF/35V
C13,C16 AECETS1C220B AL CHEM CAPACITOR 2 22µF/16V
C482 AECETS1H010B AL CHEM CAPACITOR 1 1µF/50V
C483 AECETS1HR47B AL CHEM CAPACITOR 1 0.47µF/50V
C485 AECETS1H2R2B AL CHEM CAPACITOR 1 2.2µF/16V
CX320 H2B800400007 CERAMIC RESONATOR 1 8.0MHz
DISP110 L5AAAEC00061 LCD 1
DISP HOLDER F66177D60AP LCD HOLDER 1
D40,D220,D221,D226,D227 MA2C19600E DIODE 5
D10-D13 B0EAKT000025 DIODE 4
D480 MA2C700A0F DIODE 1
IC1 MN101C78AEG L.S.I. 1
IC350 C0EBE0000401 IC 1
IC480 C0ABBA000230 IC 1
Q10,Q180 B1BAAJ000003 TRANSISTOR 2
D25 D4EAY271A036 ZENER RESISTOR 1 270V
D26,D27 D4EAY112A036 ZENER RESISTOR 2 1100V
RY1 AEBGJQC25F18 POWER RELAY 1
T10 G4C2AAD00005 LOW VOLTAGE TRANSFORMER 1 120V
SW1,SW2,SW6,SW7,SW8,SW9,SW10, EVQ11L05R SWITCH 11
SW11,SW12,SW13, SW14
RE80 EVEJ1HF2224B REVOLVING ENCODER 1
ZD10 B0BA5R600016 ZENER DIODE 1
10.4.2. NN-ST678S
C13,C16 AECETS1C220B AL CHEM CAPACITOR 2 22µF/16V
DISP110 L5AAAEC00057 LCD 1
DISP HOLDER F66174U20AP LCD HOLDER 1
D220-D222,D224,D227 MA2C19600E DIODE 5
IC1 MN101C78AEH L.S.I. 1
IC350 C0EBE0000401 IC 1
VZ1 D3CA6103A017 VARISTOR 1 10KΩ
39

10.4.3. NN-ST658W
C13 AECETS1C220B AL CHEM CAPACITOR 2 22µF/16V
D220-D222,D224,D227 MA2C19600E DIODE 5
IC1 MN101C78ADD L.S.I. 1
IC350 C0EBE0000401 IC 1
VZ1 D3CA6103A017 VARISTOR 1 10KΩ
01/08
S-8X0
S-8V6
S-8V7
40 Printed in China

NNSD 698 S

Uploaded by

Copyright:

Available Formats

NNSD 698 S

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

NNSD 698 S

Uploaded by

Copyright:

Available Formats

ORDER NO.

© 2008 Panasonic Home Appliances Microwave

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

2 DESCRIPTION OF OPERATING SEQUENCE

Downloaded from www.Manualslib.com manuals search engine

Explanation of the Auto Sensor Cooking process 2.5. Sensor reheat

Downloaded from www.Manualslib.com manuals search engine

3 CAUTIONS TO BE OBSERVED WHEN

3.1. Check the grounding

3.2. Inverter warnings

H.V. Inverter warning

Downloaded from www.Manualslib.com manuals search engine

Discharging the high voltage capacitors 3.6. Verification after repair

WARNING 3. Check for microwave energy leakage. (Refer to procedure

Downloaded from www.Manualslib.com manuals search engine

4 DISASSEMBLY AND PARTS REPLACEMENT

Downloaded from www.Manualslib.com manuals search engine

4.3. Low voltage transformer 4.5. Door assembly

Downloaded from www.Manualslib.com manuals search engine

4.6. Turntable motor 4.7. Steam sensor

Downloaded from www.Manualslib.com manuals search engine

1. Discharge high voltage charge.

7. Remove 1 screw holding H.V.Inverter to Inverter bracket.

5. Bend back 1 locking metal tab on the base.

8. Remove 1 screw holding grounding plate to H.V. Inverter.

9. Seperate H.V. Inverter from Inverter bracket by freeing 3

Downloaded from www.Manualslib.com manuals search engine

5 COMPONENT TEST PROCEDURE

1. Unplug lead connectors to Power Relay RY1 and verify

5.2. Monitor Interlock Switch

Downloaded from www.Manualslib.com manuals search engine

5.5. Inverter power supply (U)

5.6. Temperature thermistor

If the resistance reading is out of the range stated here, the

Downloaded from www.Manualslib.com manuals search engine

6 MEASUREMENTS AND ADJUSTMENTS

6.1. Adjustment of primary latch

Downloaded from www.Manualslib.com manuals search engine

7 PROCEDURE FOR MEASURING MICROWAVE ENERGY

Downloaded from www.Manualslib.com manuals search engine

7.4. At least once a year, have the

Downloaded from www.Manualslib.com manuals search engine

8.1. (Troubleshooting) Oven stops operation during cooking

Downloaded from www.Manualslib.com manuals search engine

8.2. (Troubleshooting) Other problems

Downloaded from www.Manualslib.com manuals search engine

8.3. Troubleshooting of inverter circuit (U) and magnetron

Alternate way to troubleshoot oven with AC Ampere meter used

Downloaded from www.Manualslib.com manuals search engine

8.4. SIMPLE WAY OF H.V. INVERTER/MAGNETRON TROUBLESHOOTING

1. D702 shorted Replace H.V.Inverter(F606Y8M00AP)

8.5. H.V.INVERTER BOARD MAIN PARTS LIST (F606Y8M00AP)

Downloaded from www.Manualslib.com manuals search engine

8.6. How to check the semiconductors using an OHM meter

Downloaded from www.Manualslib.com manuals search engine