LM117, LM317-N Wide Temperature Three-Pin Adjustable Regulator

Product Sample & Technical Tools & Support &
Folder Buy Documents Software Community
LM117, LM317-N
SNVS774P – MAY 2004 – REVISED OCTOBER 2015
LM117, LM317-N Wide Temperature Three-Pin Adjustable Regulator

1 Features 3 Description
•
1 Typ. 0.1% Load Regulation The LM117 and LM317-N series of adjustable 3-pin
positive voltage regulators are capable of supplying in
• Typ. 0.01%/V Line Regulation excess of 1.5 A over a 1.25-V to 37-V output range
• 1.5-A Output Current and a wide temperature range. They are
• Adjustable Output Down to 1.25 V exceptionally easy to use and require only two
• Current Limit Constant With Temperature external resistors to set the output voltage. Further,
both line and load regulation are better than standard
• 80-dB Ripple Rejection fixed regulators.
• Short-Circuit Protected Output
The LM117 and LM317-N offer full overload
• −55°C to 150°C Operating Temperature Range protection such as current limit, thermal overload
(LM117) protection and safe area protection. All overload
protection circuitry remains fully functional even if the
2 Applications adjustment terminal is disconnected.
• Automotive LED Lighting Typically, no capacitors are needed unless the device
• Battery Chargers is situated more than 6 inches from the input filter
capacitors, in which case an input bypass is needed.
• Post Regulation for Switching Supplies An optional output capacitor can be added to improve
• Constant Current Regulators transient response. The adjustment terminal can be
• Microprocessor Supplies bypassed to achieve very high ripple rejection ratios
that are difficult to achieve with standard 3-terminal
Typical Application regulators.
LM317-N Because the regulator is floating and detects only the
input-to-output differential voltage, supplies of several
hundred volts can be regulated as long as the
maximum input-to-output differential is not exceeded.
That is, avoid short-circuiting the output.
By connecting a fixed resistor between the
adjustment pin and output, the LM117 and LM317-N
can be also used as a precision current regulator.
Supplies with electronic shutdown can be achieved
by clamping the adjustment terminal to ground, which
programs the output to 1.25 V where most loads draw
little current.
For applications requiring greater output current, see
data sheets for LM150 series (3 A), SNVS772, and
LM138 series (5 A), SNVS771. For the negative
*Needed if device is more than 6 inches from filter complement, see LM137 (SNVS778) series data
capacitors. sheet.
†Optional—improves transient response Device Information(1)
æ R2 ö
+ I ADJ (R2 )
PART NUMBER PACKAGE BODY SIZE (NOM)
VOUT = 1.25 V ç 1 +
†† è R1 ÷ø TO-3 (2) 38.94 mm x 25.40 mm
LM117
TO (3) 8.255 mm × 8.255 mm
TO-3 (2) 38.94 mm x 25.40 mm
TO-220 (3) 14.986 mm × 10.16 mm
TO-263 (3) 10.18 mm × 8.41 mm
LM317-N
SOT-223 (4) 6.50 mm × 3.50 mm
TO (3) 8.255 mm × 8.255 mm
TO-252 (3) 6.58 mm × 6.10 mm
(1) For all available packages, see the orderable addendum at
1
the end of the data sheet.
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM117, LM317-N
SNVS774P – MAY 2004 – REVISED OCTOBER 2015 www.ti.com
Table of Contents
1 Features .................................................................. 1 8.3 Feature Description................................................. 13
2 Applications ........................................................... 1 8.4 Device Functional Modes........................................ 13
3 Description ............................................................. 1 9 Application and Implementation ........................ 15
4 Revision History..................................................... 2 9.1 Application Information............................................ 15
9.2 Typical Applications ................................................ 15
5 Device Comparison Table..................................... 3
6 Pin Configuration and Functions ......................... 3 10 Power Supply Recommendations ..................... 27
7 Specifications......................................................... 5 11 Layout................................................................... 27
11.1 Layout Guidelines ................................................. 27
7.1 Absolute Maximum Ratings ...................................... 5
11.2 Layout Example .................................................... 27
7.2 ESD Ratings.............................................................. 5
11.3 Thermal Considerations ........................................ 28
7.3 Recommended Operating Conditions....................... 5
7.4 Thermal Information, LM117 ..................................... 5 12 Device and Documentation Support ................. 35
7.5 Thermal Information, LM317-N ................................. 6 12.1 Documentation Support ........................................ 35
7.6 LM117 Electrical Characteristics............................... 6 12.2 Related Links ........................................................ 35
7.7 LM317-N Electrical Characteristics........................... 7 12.3 Community Resources.......................................... 35
7.8 Typical Characteristics .............................................. 8 12.4 Trademarks ........................................................... 35
12.5 Electrostatic Discharge Caution ............................ 35
8 Detailed Description ............................................ 11
12.6 Glossary ................................................................ 35
8.1 Overview ................................................................. 11
8.2 Functional Block Diagram ....................................... 12 13 Mechanical, Packaging, and Orderable
Information ........................................................... 35
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision O (January 2014) to Revision P Page
• Added, updated, or renamed the following sections: Description; Pin Configuration and Functions; Specifications;
ESD Ratings table; Application and Implementation; Power Supply Recommendations; Layout; Mechanical,
Packaging, and Ordering Information .................................................................................................................................... 1
• Removed information regarding LM317A, formerly part of this data sheet. LM317A can now be found in the TI
catalog under literature number SNVSAC2 ........................................................................................................................... 1
Changes from Revision N (August 2013) to Revision O Page
• Deleted MDT Package (over Full Operating Temperature Range) ....................................................................................... 7

• Changed Current Limit MIN from 0.112 to 0.15 and TYP from 0.3 to 0.4 for (VIN – VOUT) = 40 V in the LM317A
and LM317-N Electrical Characteristics Section .................................................................................................................... 7
• Deleted MDT Package ........................................................................................................................................................... 7
2 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated
Product Folder Links: LM117 LM317-N

LM117, LM317-N
www.ti.com SNVS774P – MAY 2004 – REVISED OCTOBER 2015
5 Device Comparison Table
Table 1. LM317 Family Options

PART NUMBER TEMPERATURE DESCRIPTION PRODUCT FOLDER
LM317-N 0°C to 125°C 40-V, 1.5-A Catalog device Click here
LM317A −40°C to 125°C 40-V, 1.5-A Industrial device Click here
LM317HV 0°C to 125°C 60-V, 1.5-A Catalog device Click here
LM317L-N −40°C to 125°C 40-V, 0.1-A, Industrial device Click here
LM117 −55°C to 150°C 40-V, 1.5-A Extended-temperature device Click here
LM117HV −55°C to 150°C 60-V, 1.5-A Extended-temperature device Click here
LM117HVQML −55°C to 125°C 60-V, 1.5-A Military-grade device per spec MIL-PRF-38535 Click here
LM117HVQML-SP −55°C to 125°C 60-V, 1.5-A Space-grade device Click here
LM117JAN −55°C to 125°C 40-V, 1.5-A Military-grade device per spec MIL-PRF-38510 Click here
LM117QML −55°C to 125°C 40-V, 1.5-A Military-grade device per spec MIL-PRF-38535 Click here
LM117QML-SP −55°C to 125°C 40-V, 1.5-A Space-grade device Click here
6 Pin Configuration and Functions
NDS Metal Can Package

2-Pin TO-3 NDT Metal Can Package
Bottom View 3-Pin TO
Bottom View
Case is Output
Case is Output
Pin Functions, Metal Can Packages

PIN
I/O DESCRIPTION
NAME TO-3 TO
ADJ 1 2 — Adjust pin
VOUT CASE 3, CASE O Output voltage pin for the regulator
VIN 2 1 I Input voltage pin for the regulator
Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 3

LM117, LM317-N
KTT Surface-Mount Package DCY Surface-Mount Package

3-Pin DDPAK/TO-263 4-Pin SOT-223
Top View Top View
NDP Surface-Mount Package

NDE Plastic Package 3-Pin TO-252
3-Pin TO-220 Front View
Front View
Pin Functions
PIN
I/O DESCRIPTION
NAME TO-263 TO-220 SOT-223 TO-252
ADJ 1 1 1 1 — Adjust pin
VOUT 2, TAB 2, TAB 2, 4 2, TAB O Output voltage pin for the regulator
VIN 3 3 3 3 I Input voltage pin for the regulator

LM117, LM317-N
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1) (2)
MIN MAX UNIT
Power dissipation Internally Limited
Input-output voltage differential −0.3 40 V
Metal package (soldering, 10 seconds) 300 °C
Lead temperature
Plastic package (soldering, 4 seconds) 260 °C
Storage temperature, Tstg −65 150 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
7.2 ESD Ratings

VALUE UNIT
Electrostatic (1)
V(ESD) Human-body model (HBM) ±3000 V
discharge
(1) Manufacturing with less than 500-V HBM is possible with the necessary precautions. Pins listed as ±3000 V may actually have higher
performance.
7.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted)
MIN MAX UNIT
Operating temperature (LM117) −55 150 °C
Operating temperature (LM317-N) 0 125 °C
7.4 Thermal Information, LM117

LM117
NDS NDT
THERMAL METRIC (1) UNIT
(TO-3) (TO)
2 PINS 3 PINS
RθJA Junction-to-ambient thermal resistance (2) 39 186 °C/W
RθJC(top) Junction-to-case (top) thermal resistance 2 21 °C/W
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
(2) No heatsink.

LM117, LM317-N
7.5 Thermal Information, LM317-N

LM317-N
(1) (2) KTT NDE DCY NDT NDP
THERMAL METRIC UNIT
(TO-263) (TO-220) (SOT-223) (TO) (TO-252)
3 PINS 3 PINS 4 PINS 3 PINS 3 PINS
(3)
RθJA Junction-to-ambient thermal resistance 41.0 23.3 59.6 186 54 °C/W
RθJC(top) Junction-to-case (top) thermal resistance 43.6 16.2 39.3 21 51.3 °C/W
RθJB Junction-to-board thermal resistance 23.6 4.9 8.4 — 28.6 °C/W
ψJT Junction-to-top characterization parameter 10.4 2.7 1.8 — 3.9 °C/W
ψJB Junction-to-board characterization parameter 22.6 4.9 8.3 — 28.1 °C/W
RθJC(bot) Junction-to-case (bottom) thermal resistance 0.9 1.1 — — 0.9 °C/W
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
(2) When surface mount packages are used (SOT-223, TO-252), the junction to ambient thermal resistance can be reduced by increasing
the PCB copper area that is thermally connected to the package. See Heatsink Requirements for heatsink techniques.
(3) No heatsink
7.6 LM117 Electrical Characteristics

Some specifications apply over full Operating Temperature Range as noted. Unless otherwise specified, TJ = 25°C, VIN −
VOUT = 5 V, and IOUT = 10 mA. (1) (2)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
3 V ≤ (VIN − VOUT) ≤ 40 V,
Reference voltage 1.2 1.25 1.3 V
10 mA ≤ IOUT ≤ IMAX (1) (over full operating temperature range)
TJ = 25°C 0.01 0.02
Line regulation 3 V ≤ (VIN − VOUT) ≤ 40 V (3) over full operating %/V
0.02 0.05
temperature range
TJ = 25°C 0.1% 0.3%
Load regulation 10 mA ≤ IOUT ≤ IMAX (1) (3) over full operating
0.3% 1%
temperature range
Thermal regulation 20-ms pulse 0.03 0.07 %/W
Adjustment pin current over full operating temperature range 50 100 μA
10 mA ≤ IOUT ≤ IMAX (1)
Adjustment pin current change 0.2 5 μA
3 V ≤ (VIN − VOUT) ≤ 40 V (over full operating temperature range)
Temperature stability TMIN ≤ TJ ≤ TMAX (over full operating temperature range) 1%
Minimum load current (VIN − VOUT) = 40 V (over full operating temperature range) 3.5 5 mA
TO-3 Package (over full
1.5 2.2 3.4
operating temperature range)
(VIN − VOUT) ≤ 15 V A
TO-39 Package (over full
Current limit 0.5 0.8 1.8
operating temperature range)
TO-3 package 0.3 0.4
(VIN − VOUT) = 40 V A
TO-39 package 0.15 0.2
RMS output noise, % of VOUT 10 Hz ≤ f ≤ 10 kHz 0.003%
VOUT = 10 V, f = 120 Hz, CADJ = 0 μF (over full operating
65 dB
temperature range)
Ripple rejection ratio
66 80 dB
temperature range)
Long-term stability TJ = 125°C, 1000 hrs 0.3% 1%
(1) IMAX = 1.5 A for the NDS (TO-3), NDE (TO-220), and KTT (TO-263) packages. IMAX = 1.0 A for the DCY (SOT-223) package.
IMAX = 0.5 A for the NDT (TO) and NDP (TO-252) packages. Device power dissipation (PD) is limited by ambient temperature (TA),
device maximum junction temperature (TJ), and package thermal resistance (θJA). The maximum allowable power dissipation at any
temperature is : PD(MAX) = ((TJ(MAX) – TA) / θJA). All Min. and Max. limits are ensured to TI's Average Outgoing Quality Level (AOQL).
(2) Specifications and availability for military and space grades of LM117/883 can be found in the LM117QML data sheet (SNVS356).
Specifications and availability for military and space grades of LM117 can be found in the LM117JAN data sheet (SNVS365).
(3) Regulation is measured at a constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to
heating effects are covered under the specifications for thermal regulation.

LM117, LM317-N
7.7 LM317-N Electrical Characteristics (1)

Some specifications apply over full Operating Temperature Range as noted. Unless otherwise specified, TJ = 25°C, VIN −
VOUT = 5 V, and IOUT = 10 mA.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
TJ = 25°C 1.25 V
Reference voltage 3 V ≤ (VIN − VOUT) ≤ 40 V,
10 mA ≤ IOUT ≤ IMAX (1) (over Full Operating Temperature 1.2 1.25 1.3 V
Range)
TJ = 25°C 0.01 0.04
Line regulation 3V ≤ (VIN − VOUT) ≤ 40 V (2) (over full operating %/V
0.02 0.07
temperature range)
TJ = 25°C 0.1% 0.5%
Load regulation 10 mA ≤ IOUT ≤ IMAX (1) (2) (over full operating
0.3% 1.5%
temperature range)
Thermal regulation 20-ms pulse 0.04 0.07 %/W
Adjustment pin current (over full operating temperature range) 50 100 μA
(1)
10 mA ≤ IOUT ≤ IMAX (over full operating
Adjustment pin current change 0.2 5 μA
3V ≤ (VIN − VOUT) ≤ 40V temperature range)
(over full operating
Temperature stability TMIN ≤ TJ ≤ TMAX 1%
temperature range)
(over full operating
Minimum load current (VIN − VOUT) = 40 V 3.5 10 mA
temperature range)
TO-3, TO-263 Packages
(over full operating 1.5 2.2 3.4
temperature range)
SOT-223, TO-220
Packages (over full
(VIN − VOUT) ≤ 15 V 1.5 2.2 3.4 A
operating temperature
range)
Current limit
TO, TO-252 Package (over
full operating temperature 0.5 0.8 1.8
range)
TO-3, TO-263 packages 0.15 0.4
(VIN − VOUT) = 40 V SOT-223, TO-220 packages 0.15 0.4 A
TO, TO-252 package 0.075 0.2
RMS output noise, % of VOUT 10 Hz ≤ f ≤ 10 kHz 0.003%
65 dB
temperature range)
Ripple rejection ratio
VOUT = 10V, f = 120 Hz, CADJ = 10 μF (over full operating
66 80 dB
temperature range)
Long-term stability TJ = 125°C, 1000 hrs 0.3% 1%
(1) IMAX = 1.5 A for the NDS (TO-3), NDE (TO-220), and KTT (TO-263) packages. IMAX = 1.0 A for the DCY (SOT-223) package.
IMAX = 0.5 A for the NDT (TO) and NDP (TO-252) packages. Device power dissipation (PD) is limited by ambient temperature (TA),
device maximum junction temperature (TJ), and package thermal resistance (θJA). The maximum allowable power dissipation at any
temperature is : PD(MAX) = ((TJ(MAX) – TA) / θJA). All Min. and Max. limits are ensured to TI's Average Outgoing Quality Level (AOQL).
(2) Regulation is measured at a constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to
heating effects are covered under the specifications for thermal regulation.

LM117, LM317-N
7.8 Typical Characteristics

Output Capacitor = 0 μF, unless otherwise noted.
Figure 1. Load Regulation

Figure 2. Current Limit
Figure 3. Adjustment Current Figure 4. Dropout Voltage
Figure 5. VOUT vs VIN, VOUT = VREF Figure 6. VOUT vs VIN, VOUT = 5 V

LM117, LM317-N
Typical Characteristics (continued)

Figure 7. Temperature Stability Figure 8. Minimum Operating Current
Figure 9. Ripple Rejection Figure 10. Ripple Rejection
Figure 11. Ripple Rejection Figure 12. Output Impedance

LM117, LM317-N
Typical Characteristics (continued)

Figure 13. Line Transient Response Figure 14. Load Transient Response

LM117, LM317-N
8 Detailed Description
8.1 Overview
In operation, the LM317-N develops a nominal 1.25-V reference voltage, VREF, between the output and
adjustment terminal. The reference voltage is impressed across program resistor R1 and, because the voltage is
constant, a constant current I1 then flows through the output set resistor R2, giving an output voltage calculated
by Equation 1:
æ R2 ö
VOUT = 1.25 V ç 1 + + I ADJ (R2 )
è R1 ÷ø (1)
LM317-N
Figure 15. Setting the VOUT Voltage
Because the 100-μA current from the adjustment terminal represents an error term, the LM317-N was designed
to minimize IADJ and make it very constant with line and load changes. To do this, all quiescent operating current
is returned to the output establishing a minimum load current requirement. If there is insufficient load on the
output, the output will rise.

LM117, LM317-N
8.2 Functional Block Diagram

LM117, LM317-N
8.3 Feature Description

8.3.1 Load Regulation
The LM317-N is capable of providing extremely good load regulation but a few precautions are needed to obtain
maximum performance. The current set resistor, R1, must be connected near the output terminal of the regulator
rather than near the load. If R1 is placed too far from the output terminal, then the increased trace resistance, RS,
will cause an error voltage drop in the adjustment loop and degrade load regulation performance. Therefore, R1
must be placed as close as possible to the output terminal to minimize RS and maximize load regulation
performance.
Figure 16 shows the effect of the trace resistance, RS, when R1 is placed far from the output terminal of the
regulator. It is clear that RS will cause an error voltage drop especially during higher current loads, so it is
important to minimize the RS trace resistance by keeping R1 close to the regulator output terminal.
LM317-N
Figure 16. Regulator With Line Resistance in Output Lead
With the TO-3 package, it is easy to minimize the resistance from the case to the set resistor, by using two
separate leads to the case. However, with the TO package, care must be taken to minimize the wire length of the
output lead. The ground of R2 can be returned near the ground of the load to provide remote ground sensing
and improve load regulation.
8.4 Device Functional Modes

8.4.1 External Capacitors
An input bypass capacitor is recommended. A 0.1-μF disc or 1-μF solid tantalum on the input is suitable input
bypassing for almost all applications. The device is more sensitive to the absence of input bypassing when
adjustment or output capacitors are used, but the above values will eliminate the possibility of problems.
The adjustment terminal can be bypassed to ground on the LM317-N to improve ripple rejection. This bypass
capacitor prevents ripple from being amplified as the output voltage is increased. With a 10-μF bypass capacitor,
80-dB ripple rejection is obtainable at any output level. Increases over 10 μF do not appreciably improve the
ripple rejection at frequencies above 120 Hz. If the bypass capacitor is used, it is sometimes necessary to
include protection diodes to prevent the capacitor from discharging through internal low current paths and
damaging the device.
In general, the best type of capacitors to use is solid tantalum. Solid tantalum capacitors have low impedance
even at high frequencies. Depending upon capacitor construction, it takes about 25 μF in aluminum electrolytic to
equal 1-μF solid tantalum at high frequencies. Ceramic capacitors are also good at high frequencies. However,
some types have a large decrease in capacitance at frequencies around 0.5 MHz. For this reason, 0.01-μF disc
may seem to work better than a 0.1-μF disc as a bypass.
Although the LM317-N is stable with no output capacitors, like any feedback circuit, certain values of external
capacitance can cause excessive ringing. This occurs with values between 500 pF and 5000 pF. A 1-μF solid
tantalum (or 25-μF aluminum electrolytic) on the output swamps this effect and insures stability. Any increase of
the load capacitance larger than 10 μF will merely improve the loop stability and output impedance.

LM117, LM317-N
Device Functional Modes (continued)

8.4.2 Protection Diodes
When external capacitors are used with any IC regulator, it is sometimes necessary to add protection diodes to
prevent the capacitors from discharging through low current points into the regulator. Most 10-μF capacitors have
low enough internal series resistance to deliver 20-A spikes when shorted. Although the surge is short, there is
enough energy to damage parts of the IC.
When an output capacitor is connected to a regulator and the input is shorted, the output capacitor will discharge
into the output of the regulator. The discharge current depends on the value of the capacitor, the output voltage
of the regulator, and the rate of decrease of VIN. In the LM317-N, this discharge path is through a large junction
that is able to sustain 15-A surge with no problem. This is not true of other types of positive regulators. For
output capacitors of 25 μF or less, there is no need to use diodes.
The bypass capacitor on the adjustment terminal can discharge through a low current junction. Discharge occurs
when either the input, or the output, is shorted. Internal to the LM317-N is a 50-Ω resistor which limits the peak
discharge current. No protection is needed for output voltages of 25 V or less and 10-μF capacitance. Figure 17
shows an LM317-N with protection diodes included for use with outputs greater than 25 V and high values of
output capacitance.
LM317-N
æ R2 ö
VOUT = 1.25 V ç 1 + + I ADJ (R2 )
è R1 ÷ø
D1 protects against C1
D2 protects against C2
Figure 17. Regulator With Protection Diodes

LM117, LM317-N
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers must
validate and test their design implementation to confirm system functionality.
9.1 Application Information

The LM117 and LM317-N are versatile, high performance, linear regulators with high accuracy and a wide
temperature range. An output capacitor can be added to further improve transient response, and the ADJ pin can
be bypassed to achieve very high ripple-rejection ratios. Its functionality can be utilized in many different
applications that require high performance regulation, such as battery chargers, constant current regulators, and
microprocessor supplies.
9.2 Typical Applications

9.2.1 1.25-V to 25-V Adjustable Regulator
The LM117 can be used as a simple, low-dropout regulator to enable a variety of output voltages needed for
demanding applications. By using an adjustable R2 resistor, a variety of output voltages can be made possible
as shown in Figure 18.
LM317-N
NOTE: Full output current not available at high input-output voltages

*Needed if device is more than 6 inches from filter capacitors.
†Optional—improves transient response. Output capacitors in the range of 1 μF to 1000 μF of aluminum or tantalum
electrolytic are commonly used to provide improved output impedance and rejection of transients.
Figure 18. 1.25-V to 25-V Adjustable Regulator
9.2.1.1 Design Requirements

The device component count is very minimal, employing two resistors as part of a voltage divider circuit and an
output capacitor for load regulation. An input capacitor is needed if the device is more than 6 inches from filter
capacitors. An optional bypass capacitor across R2 can also be used to improve PSRR.
9.2.1.2 Detailed Design Procedure

The output voltage is set based on the selection of the two resistors, R1 and R2, as shown in Figure 18. For
details on capacitor selection, refer to External Capacitors.

LM117, LM317-N
Typical Applications (continued)

9.2.1.3 Application Curve
As shown in Figure 19, VOUT will rise with VIN minus some dropout voltage. This dropout voltage during startup
will vary with ROUT.
Figure 19. VOUT vs VIN, VOUT = 5V
9.2.2 5-V Logic Regulator With Electronic Shutdown

Figure 20 shows a variation of the 5-V output regulator application uses the L117 along with an NPN transistor to
provide shutdown control. The NPN will either block or sink the current from the ADJ pin by responding to the
TTL pin logic. When TTL is pulled high, the NPN is on and pulls the ADJ pin to GND, and the LM117 outputs
about
1.25 V. When TTL is pulled low, the NPN is off and the regulator outputs according to the programmed
adjustable voltage.
LM317-N
NOTE: Min. output ≊ 1.2 V
Figure 20. 5-V Logic Regulator With Electronic Shutdown

LM117, LM317-N

9.2.3 Slow Turnon 15-V Regulator
An application of LM117 includes a PNP transistor with a capacitor to implement slow turnon functionality (see
Figure 21). As VIN rises, the PNP sinks current from the ADJ rail. The output voltage at start up is the addition of
the 1.25-V reference plus the drop across the base to emitter. While this is happening, the capacitor begins to
charge and eventually opens the PNP. At this point, the device functions normally, regulating the output at 15 V.
A diode is placed between C1 and VOUT to provide a path for the capacitor to discharge. Such controlled turnon
is useful for limiting the in-rush current.
LM117
Figure 21. Slow Turnon 15-V Regulator

LM117, LM317-N

9.2.4 Adjustable Regulator With Improved Ripple Rejection
To improve ripple rejection, a capacitor is used to bypass the ADJ pin to GND (see Figure 22). This is used to
smooth output ripple by cleaning the feedback path and stopping unnecessary noise from being fed back into the
device, propagating the noise.
LM317-N
NOTE: †Solid tantalum

*Discharges C1 if output is shorted to ground
Figure 22. Adjustable Regulator With Improved Ripple Rejection
9.2.5 High Stability 10-V Regulator

Using a high stability shunt voltage reference in the feedback path, such as the LM329, provides damping
necessary for a stable, low noise output (see Figure 23).
LM117
VIN VIN VOUT VOUT
15 V ADJ 10 V
R1
C1 2k
5% R2
0.1 µF
1.5 k
1%
LM329
R3
267
1%
Figure 23. High Stability 10-V Regulator

LM117, LM317-N

9.2.6 High-Current Adjustable Regulator
Using the LM195 power transistor in parallel with the LM117 can increase the maximum possible output load
current (see Figure 24). Sense resistor R1 provides the 0.6 V across base to emitter to turn on the PNP. This on
switch allows current to flow, and the voltage drop across R3 drives three LM195 power transistors designed to
carry an excess of 1 A each.
NOTE
The selection of R1 determines a minimum load current for the PNP to turn on. The higher
the resistor value, the lower the load current must be before the transistors turn on.
three LM195 devices in parallel
LM117
NOTE: ‡Optional—improves ripple rejection

†Solid tantalum
*Minimum load current = 30 mA
Figure 24. High-Current Adjustable Regulator

LM117, LM317-N

9.2.7 Emitter-Follower Current Amplifier
The LM117 is used as a constant current source in the emitter follower circuit (see Figure 25). The LM195 power
transistor is being used as a current gain amplifier, boosting the INPUT current. The LM117 provides a stable
current bias than just using a resistor.
LM117
Figure 25. Emitter-Follower Current Amplifier
9.2.8 1-A Current Regulator

A simple, fixed current regulator can be made by placing a resistor between the VOUT and ADJ pins of the LM117
(see Figure 26). By regulating a constant 1.25 V between these two terminals, a constant current is delivered to
the load.
LM117
Figure 26. 1-A Current Regulator

LM117, LM317-N

9.2.9 Common-Emitter Amplifier
Sometimes it is necessary to use a power transistor for high current gain. In this case, the LM117 provides
constant current at the collector of the LM195 in this common emitter application (see Figure 27). The 1.25-V
reference between VOUT and ADJ is maintained across the 2.4-Ω resistor, providing about 500-mA constant bias
current into the collector of the LM195.
LM117
Figure 27. Common-Emitter Amplifier

LM117, LM317-N

9.2.10 Low-Cost 3-A Switching Regulator
The LM317-N can be used in a switching buck regulator application in cost sensitive applications that require
high efficiency. The switch node above D1 oscillates between ground and VIN, as the voltage across sense
resistor R1 drives the power transistor on and off. Figure 28 exhibits self-oscillating behavior by negative
feedback through R6 and C3 to the ADJ pin of the LM317-N.
LM317-N
NOTE: †Solid tantalum

*Core—Arnold A-254168-2 60 turns
Figure 28. Low-Cost 3-A Switching Regulator

LM117, LM317-N

9.2.11 Current-Limited Voltage Regulator
A maximum limit on output current can be set using the circuit shown in Figure 29. The load current travels
through R3 and R4. As the load current increases, the voltage drop across R3 increases until the NPN transistor
is driven, during which the ADJ pin is pulled down to ground and the output voltage is pulled down to the
reference voltage of 1.25 V.
LM317-N
600 mV
-Short circuit current is approximately , or 210 mA
R3
(Compared to LM117's higher current limit)
—At 50 mA output only ¾ volt of drop occurs in R3 and R4
Figure 29. Current-Limited Voltage Regulator
9.2.12 Adjusting Multiple On-Card Regulators With Single Control

Figure 30 shows how multiple LM117 regulators can be controlled by setting one resistor. Because each device
maintains the reference voltage of about 1.25 V between its VOUT and ADJ pins, we can connect each ADJ rail to
a single resistor, setting the same output voltage across all devices. This allows for independent outputs, each
responding to its corresponding input only. Designers must also consider that by the nature of the circuit,
changes to R1 and R2 will affect all regulators.
LM117
NOTE: *All outputs within ±100 mV

†Minimum load—10 mA
Figure 30. Adjusting Multiple On-Card Regulators With Single Control

LM117, LM317-N

9.2.13 AC Voltage Regulator
In Figure 31, the top regulator is +6 V above the bottom regulator. It is clear that when the input rises above +6 V
plus the dropout voltage, only the top LM317-N regulates +6 V at the output. When the input falls below –6 V
minus the dropout voltage, only the bottom LM317-N regulates –6 V at the output. For regions where the output
is not clipped, there is no regulation taking place, so the output follows the input.
LM317-N
LM317-N
Figure 31. AC Voltage Regulator
9.2.14 12-V Battery Charger

The LM317-N can be used in a battery charger application shown in Figure 32, where the device maintains either
constant voltage or constant current mode depending on the current charge of the battery. To do this, the part
senses the voltage drop across the battery and delivers the maximum charging current necessary to charge the
battery. When the battery charge is low, there exists a voltage drop across the sense resistor RS, providing
constant current to the battery at that instant. As the battery approaches full charge, the potential drop across RS
approaches zero, reducing the current and maintaining the fixed voltage of the battery.
LM317-N
Use of RS allows low charging rates with fully charged battery.
Figure 32. 12-V Battery Charger

LM117, LM317-N

9.2.15 Adjustable 4-A Regulator
Using three LM317-N devices in parallel increases load current capability (Figure 33). Output voltage is set by
the variable resistor tied to the non-inverting terminal of the operational amplifier, and reference current to the
transistor is developed across the 100 Ω resistor. When output voltage rises, the operational amplifier corrects by
drawing current from the base, closing the transistor. This effectively pulls ADJ down and lowers the output
voltage through negative feedback.
LM317-N
LM317-N
LM317-N
Figure 33. Adjustable 4-A Regulator

LM117, LM317-N

9.2.16 Current-Limited 6-V Charger
The current in a battery charger application is limited by switching between constant current and constant voltage
states (see Figure 34). When the battery pulls low current, the drop across the 1 Ω resistor is not substantial and
the NPN remains off. A constant voltage is seen across the battery, as regulated by the resistor divider. When
current through the battery rises past peak current, the 1 Ω provides enough voltage to turn the transistor on,
pulling ADJ close to ground. This results in limiting the maximum current to the battery.
LM317-N
*Sets peak current (0.6A for 1Ω)

**The 1000-μF is recommended to filter out input transients
Figure 34. Current-Limited 6-V Charger
9.2.17 Digitally Selected Outputs

Figure 35 demonstrates a digitally selectable output voltage. In its default state, all transistors are off and the
output voltage is set based on R1 and R2. By driving certain transistors, the associated resistor is connected in
parallel to R2, modifying the output voltage of the regulator.
LM317-N
*Sets maximum VOUT
Figure 35. Digitally Selected Outputs
(2)

LM117, LM317-N
10 Power Supply Recommendations

The input supply to the LM117 and LM317-N must be kept at a voltage level such that its maximum input to
output differential voltage is not exceeded. The minimum dropout voltage must also be met with extra headroom
when possible to keep the LM117 and LM317-N in regulation. An input capacitor is recommended, especially
when the input pin is located more than 6 inches away from the power supply source. For more information
regarding capacitor selection, refer to External Capacitors.
11 Layout
11.1 Layout Guidelines

Some layout guidelines must be followed to ensure proper regulation of the output voltage with minimum noise.
Traces carrying the load current must be wide to reduce the amount of parasitic trace inductance and the
feedback loop from VOUT to ADJ must be kept as short as possible. To improve PSRR, a bypass capacitor can
be placed at the ADJ pin and must be located as close as possible to the IC. In cases when VIN shorts to ground,
an external diode must be placed from VOUT to VIN to divert the surge current from the output capacitor and
protect the IC. Similarly, in cases when a large bypass capacitor is placed at the ADJ pin and VOUT shorts to
ground, an external diode must be placed from ADJ to VOUT to provide a path for the bypass capacitor to
discharge. These diodes must be placed close to the corresponding IC pins to increase their effectiveness.
11.2 Layout Example
Figure 36. Layout Example (SOT-223)

LM117, LM317-N
Layout Example (continued)
Figure 37. Layout Example (TO-220)
11.3 Thermal Considerations
11.3.1 Heatsink Requirements

The LM317-N regulators have internal thermal shutdown to protect the device from over-heating. Under all
operating conditions, the junction temperature of the LM317-N must not exceed the rated maximum junction
temperature (TJ) of 150°C for the LM117, or 125°C for the LM317-N. A heatsink may be required depending on
the maximum device power dissipation and the maximum ambient temperature of the application. To determine if
a heatsink is needed, the power dissipated by the regulator, PD, must be calculate with Equation 3:
PD = ((VIN − VOUT) × IL) + (VIN × IG) (3)
Figure 38 shows the voltage and currents which are present in the circuit.
The next parameter which must be calculated is the maximum allowable temperature rise, TR(MAX) in Equation 4:
TR(MAX) = TJ(MAX) − TA(MAX) (4)
where TJ(MAX) is the maximum allowable junction temperature (150°C for the LM117, or 125°C for the LM317-N),
and TA(MAX) is the maximum ambient temperature that will be encountered in the application.
Using the calculated values for TR(MAX) and PD, the maximum allowable value for the junction-to-ambient thermal
resistance (θJA) can be calculated with Equation 5:
θJA = (TR(MAX) / PD) (5)

LM117, LM317-N
Thermal Considerations (continued)
Figure 38. Power Dissipation Diagram
If the calculated maximum allowable thermal resistance is higher than the actual package rating, then no
additional work is needed. If the calculated maximum allowable thermal resistance is lower than the actual
package rating either the power dissipation (PD) needs to be reduced, the maximum ambient temperature TA(MAX)
needs to be reduced, the thermal resistance (θJA) must be lowered by adding a heatsink, or some combination of
these.
If a heatsink is needed, the value can be calculated from Equation 6:
θHA ≤ (θJA – (θCH + θJC))
where
• θCH is the thermal resistance of the contact area between the device case and the heatsink surface
• θJC is thermal resistance from the junction of the die to surface of the package case (6)
When a value for θHA is found using the equation shown, a heatsink must be selected that has a value that is
less than, or equal to, this number.
The θHA rating is specified numerically by the heatsink manufacturer in the catalog, or shown in a curve that plots
temperature rise vs power dissipation for the heatsink.
11.3.2 Heatsinking Surface Mount Packages

The TO-263 (KTT), SOT-223 (DCY) and TO-252 (NDP) packages use a copper plane on the PCB and the PCB
itself as a heatsink. To optimize the heat sinking ability of the plane and PCB, solder the tab of the package to
the plane.
11.3.2.1 Heatsinking the SOT-223 (DCY) Package

Figure 39 and Figure 40 show the information for the SOT-223 package. Figure 40 assumes a θJA of 74°C/W for
1-oz. copper and 59.6°C/W for 2-oz. copper and a maximum junction temperature of 125°C. See AN-1028
(SNVA036) for thermal enhancement techniques to be used with SOT-223 and TO-252 packages.

LM117, LM317-N
Figure 39. θJA vs Copper (2-oz.) Area for the SOT-223 Figure 40. Maximum Power Dissipation vs TAMB for the
Package SOT-223 Package
11.3.2.2 Heatsinking the TO-263 (KTT) Package

Figure 41 shows for the TO-263 the measured values of θJA for different copper area sizes using a typical PCB
with 1-oz. copper and no solder mask over the copper area used for heatsinking.
As shown in Figure 41, increasing the copper area beyond 1 square inch produces very little improvement. It
must also be observed that the minimum value of θJA for the TO-263 package mounted to a PCB is 32°C/W.
Figure 41. θJA vs Copper (1-oz.) Area for the TO-263 Package
As a design aid, Figure 42 shows the maximum allowable power dissipation compared to ambient temperature
for the TO-263 device (assuming θJA is 35°C/W and the maximum junction temperature is 125°C).

LM117, LM317-N
Figure 42. Maximum Power Dissipation vs TAMB for the TO-263 Package
11.3.2.3 Heatsinking the TO-252 (NDP) Package

If the maximum allowable value for θJA is found to be ≥ 54°C/W (typical rated value) for the TO-252 package, no
heatsink is needed because the package alone will dissipate enough heat to satisfy these requirements. If the
calculated value for θJA falls below these limits, a heatsink is required.
As a design aid, Table 2 shows the value of the θJA of NDP the package for different heatsink area. The copper
patterns that we used to measure these θJAs are shown in Figure 47. Figure 43 reflects the same test results as
what are in Table 2.
Figure 44 shows the maximum allowable power dissipation versus ambient temperature for the TO-252 device.
Figure 45 shows the maximum allowable power dissipation versus copper area (in2) for the TO-252 device. See
AN-1028 (SNVA036) for thermal enhancement techniques to be used with SOT-223 and TO-252 packages.

LM117, LM317-N

Table 2. θJA Different Heatsink Area
LAYOUT COPPER AREA THERMAL RESISTANCE
Top Side (in2) (1) Bottom Side (in2) (θJA°C/W) TO-252
1 0.0123 0 103
2 0.066 0 87
3 0.3 0 60
4 0.53 0 54
5 0.76 0 52
6 1.0 0 47
7 0.066 0.2 84
8 0.066 0.4 70
9 0.066 0.6 63
10 0.066 0.8 57
11 0.066 1.0 57
12 0.066 0.066 89
13 0.175 0.175 72
14 0.284 0.284 61
15 0.392 0.392 55
16 0.5 0.5 53
(1) Tab of device attached to topside of copper.
Figure 43. θJA vs 2-oz. Copper Area for TO-252 Figure 44. Maximum Allowable Power Dissipation vs
Ambient Temperature for TO-252

LM117, LM317-N
Figure 45. Maximum Allowable Power Dissipation vs 2-oz. Copper Area for TO-252
Figure 46. Top View of the Thermal Test Pattern in Actual Scale

LM117, LM317-N
Figure 47. Bottom View of the Thermal Test Pattern in Actual Scale

LM117, LM317-N
12 Device and Documentation Support
12.1 Documentation Support

12.1.1 Related Documentation
• For applications requiring greater output current, see LM150 series (3A) (SNVS772) and LM138 series (5A)
(SNVS771) data sheets.
• For the negative complement, see LM137 (SNVS778) series data sheet.
• For specifications and availability for military and space grades of LM117/883, see the LM117QML data sheet
(SNVS356).
• Specifications and availability for military and space grades of LM117JAN can be found in the LM117 data
sheet (SNVS365).
• For thermal enhancement techniques to be used with SOT-223 and TO-252 packages, see AN-1028,
Maximum Power Enhancement Techniques for Power Packages (SNVA036).
12.2 Related Links

The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 3. Related Links

TECHNICAL TOOLS & SUPPORT &
PARTS PRODUCT FOLDER SAMPLE & BUY
DOCUMENTS SOFTWARE COMMUNITY
LM117 Click here Click here Click here Click here Click here
LM317-N Click here Click here Click here Click here Click here
12.3 Community Resources

The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.

PACKAGE OPTION ADDENDUM
www.ti.com 18-Oct-2017
PACKAGING INFORMATION
Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) (6) (3) (4/5)
LM117H ACTIVE TO NDT 3 500 Green (RoHS AU | Call TI Level-1-NA-UNLIM -55 to 150 ( LM117HP+, LM117H
& no Sb/Br) P+)
LM117H/NOPB ACTIVE TO NDT 3 500 Green (RoHS AU | Call TI Level-1-NA-UNLIM -55 to 150 ( LM117HP+, LM117H
& no Sb/Br) P+)
LM117K ACTIVE TO-3 NDS 2 50 TBD Call TI Call TI -55 to 125 LM117K
STEELP+
LM117K STEEL ACTIVE TO-3 NDS 2 50 TBD Call TI Call TI -55 to 150 LM117K
STEELP+
LM117K STEEL/NOPB ACTIVE TO-3 NDS 2 50 Green (RoHS Call TI Level-1-NA-UNLIM -55 to 150 LM117K
& no Sb/Br) STEELP+
LM317EMP NRND SOT-223 DCY 4 1000 TBD Call TI Call TI 0 to 125 N01A
LM317EMP/NOPB ACTIVE SOT-223 DCY 4 1000 Green (RoHS CU SN Level-1-260C-UNLIM 0 to 125 N01A
& no Sb/Br)
LM317EMPX/NOPB ACTIVE SOT-223 DCY 4 2000 Green (RoHS CU SN Level-1-260C-UNLIM 0 to 125 N01A
& no Sb/Br)
LM317MDT/NOPB ACTIVE TO-252 NDP 3 75 Green (RoHS CU SN Level-2-260C-1 YEAR 0 to 125 LM317
& no Sb/Br) MDT
LM317MDTX/NOPB ACTIVE TO-252 NDP 3 2500 Green (RoHS CU SN Level-2-260C-1 YEAR 0 to 125 LM317
& no Sb/Br) MDT
LM317S/NOPB ACTIVE DDPAK/ KTT 3 45 Pb-Free (RoHS CU SN Level-3-245C-168 HR 0 to 125 LM317S
TO-263 Exempt) P+
LM317SX/NOPB ACTIVE DDPAK/ KTT 3 500 Pb-Free (RoHS CU SN Level-3-245C-168 HR 0 to 125 LM317S
TO-263 Exempt) P+
LM317T NRND TO-220 NDE 3 45 TBD Call TI Call TI LM317T P+
LM317T/LF01 ACTIVE TO-220 NDG 3 45 Pb-Free (RoHS CU SN Level-4-260C-72 HR LM317T P+
Exempt)
LM317T/NOPB ACTIVE TO-220 NDE 3 45 Green (RoHS CU SN Level-1-NA-UNLIM 0 to 125 LM317T P+
& no Sb/Br)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com 18-Oct-2017
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com 30-Sep-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal

Device Package Package Pins SPQ Reel Reel A0 B0 K0 P1 W Pin1
Type Drawing Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LM317EMP SOT-223 DCY 4 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3
LM317EMP/NOPB SOT-223 DCY 4 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3
LM317EMPX/NOPB SOT-223 DCY 4 2000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3
LM317MDTX/NOPB TO-252 NDP 3 2500 330.0 16.4 6.9 10.5 2.7 8.0 16.0 Q2
LM317SX/NOPB DDPAK/ KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
TO-263
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com 30-Sep-2015
*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM317EMP SOT-223 DCY 4 1000 367.0 367.0 35.0
LM317EMP/NOPB SOT-223 DCY 4 1000 367.0 367.0 35.0
LM317EMPX/NOPB SOT-223 DCY 4 2000 367.0 367.0 35.0
LM317MDTX/NOPB TO-252 NDP 3 2500 367.0 367.0 38.0
LM317SX/NOPB DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0
Pack Materials-Page 2
MECHANICAL DATA
NDE0003B
www.ti.com
MECHANICAL DATA
KTT0003B
TS3B (Rev F)
BOTTOM SIDE OF PACKAGE
www.ti.com
MECHANICAL DATA
NDS0002A
www.ti.com
MECHANICAL DATA
MPDS094A – APRIL 2001 – REVISED JUNE 2002
DCY (R-PDSO-G4) PLASTIC SMALL-OUTLINE
6,70 (0.264)
6,30 (0.248)
3,10 (0.122)
2,90 (0.114)
4
0,10 (0.004) M
7,30 (0.287) 3,70 (0.146)

6,70 (0.264) 3,30 (0.130)
Gauge Plane
1 2 3
0,25 (0.010)
0,84 (0.033) 0°–10°
2,30 (0.091)
0,66 (0.026)
0,10 (0.004) M
4,60 (0.181) 0,75 (0.030) MIN
1,70 (0.067)
1,80 (0.071) MAX 1,50 (0.059)
0,35 (0.014)
0,23 (0.009)
Seating Plane
0,10 (0.0040) 0,08 (0.003)

0,02 (0.0008)
4202506/B 06/2002
NOTES: A. All linear dimensions are in millimeters (inches).

B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion.
D. Falls within JEDEC TO-261 Variation AA.
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

MECHANICAL DATA
NDG0003F
T03F (Rev B)
www.ti.com
PACKAGE OUTLINE
NDP0003B SCALE 1.500
TO-252 - 2.55 mm max height
TRANSISTOR OUTLINE
10.42
9.40
6.22 1.27
B
5.97 0.88 A
(2.345)
2.285 (2.5)
2 5.46 6.73
4.57
4.96 6.35
3
0.88
3X 1.02 PKG
0.64 OPTIONAL
0.25 C A B 0.64
8 8
TOP & BOTTOM
1.14
0.89 C
2.55 MAX
SEATING PLANE
0.17 0.60 0.88

0.46 0.46
0.51 MIN
4.32 MIN
2 4
4219870/A 03/2018
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Reference JEDEC registration TO-252.
www.ti.com
EXAMPLE BOARD LAYOUT
NDP0003B TO-252 - 2.55 mm max height
TRANSISTOR OUTLINE
SEE SOLDER MASK

DETAIL
2X (2.15)
2X (1.3) (5.7)
4 SYMM
(4.57) (5.5)
(R0.05) TYP
(4.38) (2.285)
PKG
LAND PATTERN EXAMPLE

EXPOSED METAL SHOWN
SCALE: 8X
METAL EDGE 0.07 MIN

0.07 MAX ALL AROUND
ALL AROUND
METAL UNDER
EXPOSED SOLDER MASK
METAL
EXPOSED
METAL
SOLDER MASK SOLDER MASK
OPENING OPENING
NON SOLDER MASK SOLDER MASK DEFINED
DEFINED
(PREFERRED)
SOLDER MASK DETAIL
4219870/A 03/2018
NOTES: (continued)
4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature numbers
SLMA002(www.ti.com/lit/slm002) and SLMA004 (www.ti.com/lit/slma004).
5. Vias are optional depending on application, refer to device data sheet. It is recommended that vias under paste be filled, plugged or tented.
www.ti.com
EXAMPLE STENCIL DESIGN
NDP0003B TO-252 - 2.55 mm max height
TRANSISTOR OUTLINE
(1.35) TYP
2X (2.15)
(0.26)
2X (1.3) (R0.05) TYP
(1.32) TYP
(4.57)
16X (1.12)
16X (1.15)
(4.38)
PKG
SOLDER PASTE EXAMPLE

BASED ON 0.125 MM THICK STENCIL
SCALE: 8X
4219870/A 03/2018
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
7. Board assembly site may have different recommendations for stencil design.
www.ti.com
MECHANICAL DATA
NDT0003A
H03A (Rev D)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-
compliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated

LM117, LM317-N Wide Temperature Three-Pin Adjustable Regulator

Uploaded by

Copyright:

Available Formats

LM117, LM317-N Wide Temperature Three-Pin Adjustable Regulator

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LM117, LM317-N Wide Temperature Three-Pin Adjustable Regulator

Uploaded by

Copyright:

Available Formats

Product Sample & Technical Tools & Support &

Folder Buy Documents Software Community

LM117, LM317-N Wide Temperature Three-Pin Adjustable Regulator

Changes from Revision O (January 2014) to Revision P Page

Changes from Revision N (August 2013) to Revision O Page

• Deleted MDT Package (over Full Operating Temperature Range) ....................................................................................... 7

2 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated

Product Folder Links: LM117 LM317-N

5 Device Comparison Table

Table 1. LM317 Family Options

6 Pin Configuration and Functions

NDS Metal Can Package

Pin Functions, Metal Can Packages

Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 3

KTT Surface-Mount Package DCY Surface-Mount Package

NDP Surface-Mount Package

4 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated

Product Folder Links: LM117 LM317-N

7.2 ESD Ratings

7.3 Recommended Operating Conditions

7.4 Thermal Information, LM117

Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 5

7.5 Thermal Information, LM317-N

7.6 LM117 Electrical Characteristics

6 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated

Product Folder Links: LM117 LM317-N

7.7 LM317-N Electrical Characteristics (1)

Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 7

7.8 Typical Characteristics

Figure 1. Load Regulation

Figure 3. Adjustment Current Figure 4. Dropout Voltage

Figure 5. VOUT vs VIN, VOUT = VREF Figure 6. VOUT vs VIN, VOUT = 5 V

8 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated

Product Folder Links: LM117 LM317-N

Typical Characteristics (continued)

Figure 7. Temperature Stability Figure 8. Minimum Operating Current

Figure 9. Ripple Rejection Figure 10. Ripple Rejection

Figure 11. Ripple Rejection Figure 12. Output Impedance

Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 9

Typical Characteristics (continued)

10 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated

Product Folder Links: LM117 LM317-N

Figure 15. Setting the VOUT Voltage

Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 11

8.2 Functional Block Diagram

12 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated

Product Folder Links: LM117 LM317-N

8.3 Feature Description

Figure 16. Regulator With Line Resistance in Output Lead

8.4 Device Functional Modes

Copyright © 2004–2015, Texas Instruments Incorporated Submit Documentation Feedback 13

Device Functional Modes (continued)

Figure 17. Regulator With Protection Diodes

14 Submit Documentation Feedback Copyright © 2004–2015, Texas Instruments Incorporated

Product Folder Links: LM117 LM317-N

9 Application and Implementation

9.1 Application Information

9.2 Typical Applications

NOTE: Full output current not available at high input-output voltages