LM117HV/LM317HV 3-Terminal Adjustable Regulator

April 2000

LM117HV/LM317HV
3-Terminal Adjustable Regulator
General Description Also, it makes an especially simple adjustable switching
regulator, a programmable output regulator, or by connecting
The LM117HV/LM317HV are adjustable 3-terminal positive a fixed resistor between the adjustment and output, the
voltage regulators capable of supplying in excess of 1.5A LM117HV can be used as a precision current regulator. Sup-
over a 1.2V to 57V output range. They are exceptionally plies with electronic shutdown can be achieved by clamping
easy to use and require only two external resistors to set the the adjustment terminal to ground which programs the out-
output voltage. Further, both line and load regulation are bet- put to 1.2V where most loads draw little current.
ter than standard fixed regulators. Also, the LM117HV is
The LM117HVK STEEL and LM317HVK STEEL are pack-
packaged in standard transistor packages which are easily
aged in standard TO-3 transistor packages, while the
mounted and handled.
LM117HVH and LM317HVH are packaged in a solid Kovar
In addition to higher performance than fixed regulators, the base TO-39 transistor package. The LM317HVT uses a TO-
LM117HV series offers full overload protection available only 220 plastic package. The LM117HV is rated for operation
in IC’s. Included on the chip are current limit, thermal over- from −55˚C to +150˚C, and the LM317HV from 0˚C to
load protection and safe area protection. All overload protec- +125˚C.
tion circuitry remains fully functional even if the adjustment
terminal is disconnected.
Normally, no capacitors are needed unless the device is situ-
Features
ated more than 6 inches from the input filter capacitors in n Adjustable output down to 1.2V
which case an input bypass is needed. An optional output n Guaranteed 1.5A output current
capacitor can be added to improve transient response. The n Line regulation typically 0.01%/V
adjustment terminal can be bypassed to achieve very high n Load regulation typically 0.1%
ripple rejections ratios which are difficult to achieve with n Current limit constant with temperature
standard 3-terminal regulators. n 100% electrical burn-in
Besides replacing fixed regulators, the LM117HV is useful in n Eliminates the need to stock many voltages
a wide variety of other applications. Since the regulator is n Standard 3-lead transistor package
“floating” and sees only the input-to-output differential volt- n 80 dB ripple rejection
age, supplies of several hundred volts can be regulated as
n Output is short-circuit protected
long as the maximum input to output differential is not ex-
n P+ Product Enhancement tested
ceeded, i.e. do not short the output to ground.

Typical Applications
1.2V-45V Adjustable Regulator

DS009062-1

Full output current not available at high input-output voltages

†Optional — improves transient response. Output capacitors in the range of 1 µF to 1000 µF of aluminum or tantalum electrolytic
are commonly used to provide improved output impedance and rejection of transients.
*Needed if device is more than 6 inches from filter capacitors.

© 2000 National Semiconductor Corporation DS009062 www.national.com

LM117HV/LM317HV
Typical Applications (Continued)

Digitally Selected Outputs 5V Logic Regulator with

Electronic Shutdown*

DS009062-3

*Min. output ≈ 1.2V

DS009062-2

*Sets maximum VOUT

www.national.com 2
 LM117HV/LM317HV
Absolute Maximum Ratings (Note 1) Operating Junction Temperature Range
If Military/Aerospace specified devices are required, LM117HV −55˚C to +150˚C
please contact the National Semiconductor Sales Office/ LM317HV 0˚C to +125˚C
Distributors for availability and specifications. Storage Temperature −65˚C to +150˚C
(Note 4) Lead Temperature (Soldering, 10 sec.) 300˚C
Power Dissipation Internally limited ESD Tolerance (Note 5) 2000V
Input — Output Voltage Differential +60V, −0.3V

Electrical Characteristics (Note 2)

Parameter Conditions LM117HV LM317HV Units
Min Typ Max Min Typ Max
Line Regulation TJ = 25˚C, 3V ≤ VIN − VOUT ≤ 60V 0.01 0.02 0.01 0.04 %/V
(Note 3) IL = 10 mA
Load Regulation TJ = 25˚C, 10 mA ≤ IOUT ≤ IMAX 0.1 0.3 0.1 0.5 %
Thermal Regulation TJ = 25˚C, 20 ms Pulse 0.03 0.07 0.04 0.07 %/W
Adjustment Pin Current 50 100 50 100 µA
Adjustment Pin Current Change 10 mA ≤ IL ≤ IMAX 0.2 5 0.2 5 µA
3.0 V ≤ (VIN − VOUT) ≤ 60V
Reference Voltage 3.0 V ≤ (VIN − VOUT) ≤ 60V, (Note 4) 1.20 1.25 1.30 1.20 1.25 1.30 V
10 mA ≤ IOUT ≤ IMAX, P ≤ PMAX
Line Regulation 3.0V ≤ (VIN − VOUT) ≤ 60V, 0.02 0.05 0.02 0.07 %/V
IL = 10 mA, (Note 3)
Load Regulation 10 mA ≤ IOUT ≤ IMAX (Note 3) 0.3 1 0.3 1.5 %
Temperature Stability TMIN ≤ TJ ≤ TMAX 1 1 %
Minimum Load Current (VIN − VOUT) = 60V 3.5 7 3.5 12 mA
Current Limit (VIN − VOUT) ≤ 15V
K, T Packages 1.5 2.2 3.5 1.5 2.2 3.7 A
H Package 0.5 0.8 1.8 0.5 0.8 1.9 A
(VIN − VOUT) ≤ 60V
K, T Packages 0.3 0.3 A
H Package 0.03 0.03 A
RMS Output Noise, % of VOUT TJ = 25˚C, 10 Hz ≤ f ≤ 10 kHz 0.003 0.003 %
Ripple Rejection Ratio VOUT = 10V, f = 120 Hz 65 65 dB
CADJ = 10 µF 66 80 66 80 dB
Long-Term Stability TJ = 125˚C 0.3 1 0.3 1 %
Thermal Resistance, H Package 12 15 12 15 ˚C/W
Junction to Case T Package 4 5 ˚C/W
K Package 2.3 3 2.3 3 ˚C/W
Thermal Resistance, H Package 140 140 ˚C/W
Junction to Ambient T Package 50 ˚C/W
(no heat sink) K Package 35 35 ˚C/W
Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits.
Note 2: Unless otherwise specified, these specifications apply: −55˚C ≤ TJ ≤ +150˚C for the LM117HV, and 0˚C ≤ TJ ≤ +125˚C for the LM317HV; VIN − VOUT = 5V
and IOUT = 0.1A for the TO-39 package and IOUT = 0.5A for the TO-3 and TO-220 packages. Although power dissipation is internally limited, these specifications are
applicable for power dissipations of 2W for the TO-39 and 20W for the TO-3 and TO-220. IMAX is 1.5A for the TO-3 and TO-220 and 0.5A for the TO-39 package.
Note 3: Regulation is measured at constant junction temperature. Changes in output voltage due to heating effects must be taken into account separately. Pulse test-
ing with low duty cycle is used.
Note 4: Refer to RETS117HVH for LM117HVH or RETS117HVK for LM117HVK military specificatioins.
Note 5: Human body model, 1.5 kΩ in series with 100 pF.

3 www.national.com
LM117HV/LM317HV
Typical Performance Characteristics Output capacitor = 0 µF unless otherwise noted.

Load Regulation Current Limit Adjustment Current

DS009062-32 DS009062-33 DS009062-34

Dropout Voltage Temperature Stability Minimum Operating Current

DS009062-35 DS009062-36 DS009062-37

Ripple Rejection Ripple Rejection Ripple Rejection

DS009062-38 DS009062-40
DS009062-39

Output Impedance Line Transient Response Load Transient Response

DS009062-41 DS009062-42 DS009062-43

www.national.com 4
 LM117HV/LM317HV
Application Hints insures stability. Any increase of load capacitance larger
than 10 µF will merely improve the loop stability and output
In operation, the LM117HV develops a nominal 1.25V refer- impedance.
ence voltage, VREF, between the output and adjustment ter-
minal. The reference voltage is impressed across program Load Regulation
resistor R1 and, since the voltage is constant, a constant
The LM117HV is capable of providing extremely good load
current I1 then flows through the output set resistor R2, giv-
regulation but a few precautions are needed to obtain maxi-
ing an output voltage of
mum performance. The current set resistor connected be-
tween the adjustment terminal and the output terminal (usu-
ally 240Ω) should be tied directly to the output of the
regulator rather than near the load. This eliminates line
drops from appearing effectively in series with the reference
and degrading regulation. For example, a 15V regulator with
0.05Ω resistance between the regulator and load will have a
load regulation due to line resistance of 0.05Ω x IL. If the set
resistor is connected near the load the effective line resis-
tance will be 0.05Ω (1 + R2/R1) or in this case, 11.5 times
worse.
Figure 2 shows the effect of resistance between the regula-
tor and 240Ω set resistor.

DS009062-5

FIGURE 1.

Since the 100 µA current from the adjustment terminal repre-

sents an error term, the LM117HV was designed to minimize
IADJ and make it very constant with line and load changes.
To do this, all quiescent operating current is returned to the
DS009062-6
output establishing a minimum load current requirement. If
there is insufficient load on the output, the output will rise. FIGURE 2. Regulator with Line
Resistance in Output Lead
External Capacitors
With the TO-3 package, it is easy to minimize the resistance
An input bypass capacitor is recommended. A 0.1 µF disc or from the case to the set resistor, by using two separate leads
1 µF solid tantalum on the input is suitable input bypassing to the case. However, with the TO-5 package, care should be
for almost all applications. The device is more sensitive to taken to minimize the wire length of the output lead. The
the absence of input bypassing when adjustment or output ground of R2 can be returned near the ground of the load to
capacitors are used but the above values will eliminate the provide remote ground sensing and improve load regulation.
possiblity of problems.
The adjustment terminal can be bypassed to ground on the Protection Diodes
LM117HV to improve ripple rejection. This bypass capacitor When external capacitors are used with any IC regulator it is
prevents ripple from being amplified as the output voltage is sometimes necessary to add protection diodes to prevent
increased. With a 10 µF bypass capacitor 80 dB ripple rejec- the capacitors from discharging through low current points
tion is obtainable at any output level. Increases over 10 µF into the regulator. Most 10 µF capacitors have low enough
do not appreciably improve the ripple rejection at frequen- internal series resistance to deliver 20A spikes when
cies above 120 Hz. If the bypass capacitor is used, it is shorted. Although the surge is short, there is enough energy
sometimes necessary to include protection diodes to prevent to damage parts of the IC.
the capacitor from discharging through internal low current
When an output capacitor is connected to a regulator and
paths and damaging the device.
the input is shorted, the output capacitor will discharge into
In general, the best type of capacitors to use are solid tanta- the output of the regulator. The discharge current depends
lum. Solid tantalum capacitors have low impedance even at on the value of the capacitor, the output voltage of the regu-
high frequencies. Depending upon capacitor construction, it lator, and the rate of decrease of VIN. In the LM117HV, this
takes about 25 µF in aluminum electrolytic to equal 1 µF discharge path is through a large junction that is able to sus-
solid tantalum at high frequencies. Ceramic capacitors are tain 15A surge with no problem. This is not true of other
also good at high frequencies; but some types have a large types of positive regulators. For output capacitors of 25 µF or
decrease in capacitance at frequencies around 0.5 MHz. For less, there is no need to use diodes.
this reason, 0.01 µF disc may seem to work better than a 0.1
The bypass capacitor on the adjustment terminal can dis-
µF disc as a bypass.
charge through a low current junction. Discharge occurs
Although the LM117HV is stable with no output capacitors, when either the input or output is shorted. Internal to the
like any feedback circuit, certain values of external capaci- LM117HV is a 50Ω resistor which limits the peak discharge
tance can cause excessive ringing. This occurs with values current. No protection is needed for output voltages of 25V
between 500 pF and 5000 pF. A 1 µF solid tantalum (or 25 µF
aluminum electrolytic) on the output swamps this effect and

5 www.national.com
LM117HV/LM317HV
Application Hints (Continued)

or less and 10 µF capacitance. Figure 3 shows an LM117HV

with protection diodes included for use with outputs greater
than 25V and high values of output capacitance.

Current Limit
Internal current limit will be activated whenever the output
current exceeds the limit indicated in the Typical Perfor-
mance Characteristics. However, if during a short circuit con-
dition the regulator’s differential voltage exceeds the Abso-
lute Maximum Rating of 60V (e.g. VIN ≥ 60V, VOUT = 0V),
internal junctions in the regulator may break down and the DS009062-7

device may be damaged or fail. Failure modes range from an FIGURE 3. Regulator with Protection Diodes
apparent open or short from input to output of the regulator,
to a destroyed package (most common with the TO-220
package). To protect the regulator, the user is advised to be
aware of voltages that may be applied to the regulator during
fault conditions, and to avoid violating the Absolute Maxi- Note: D1 protects against C1
mum Ratings. D2 protects against C2

Schematic Diagram

DS009062-8

Typical Applications
Slow Turn-On 15V Regulator Adjustable Regulator with Improved
Ripple Rejection

DS009062-9 DS009062-10

†Solid tantalum
*Discharges C1 if output is shorted to ground

www.national.com 6
 LM117HV/LM317HV
Typical Applications (Continued)

High Stability 10V Regulator High Current Adjustable Regulator

DS009062-11

DS009062-12

†Solid tantalum
*Minimum load current = 30 mA
‡ Optional — improves ripple rejection

0 to 30V Regulator Power Follower

DS009062-13
DS009062-14
Full output current not available at high input-output voltages

7 www.national.com
LM117HV/LM317HV
Typical Applications (Continued)

5A Constant Voltage/Constant Current Regulator

DS009062-15

†Solid tantalum
*Lights in constant current mode

1A Current Regulator 1.2V–20V Regulator with

Minimum Program Current

DS009062-16

DS009062-17

*Minimum load current ≈ 4 mA

www.national.com 8
 LM117HV/LM317HV
Typical Applications (Continued)

High Gain Amplifier Low Cost 3A Switching Regulator

DS009062-18
DS009062-19

†Solid tantalum
*Core — Arnold A-254168-2 60 turns

4A Switching Regulator with Overload Protection

DS009062-20

†Solid tantalum
*Core — Arnold A-254168-2 60 turns

9 www.national.com
LM117HV/LM317HV
Typical Applications (Continued)

Precision Current Limiter Tracking Preregulator

DS009062-21

* 0.8Ω ≤ R1 ≤ 120Ω

DS009062-22

Adjustable Multiple On-Card Regulators

with Single Control*

DS009062-23

*All outputs within ± 100 mV

†Minimum load — 10 mA

AC Voltage Regulator 12V Battery Charger

DS009062-25

Use of RS allows low charging rates with fully charged battery.

**The 1000 µF is recommended to filter out input transients
DS009062-24

www.national.com 10
 LM117HV/LM317HV
Typical Applications (Continued)
Current Limited 6V Charger

50 mA Constant Current Battery Charger

DS009062-26

Adjustable 4A Regulator

DS009062-28

*Sets peak current (0.6A for 1Ω)

**The 1000 µF is recommended to filter out input transients

DS009062-27

11 www.national.com
LM117HV/LM317HV
Connection Diagrams (See Physical Dimension section for further information)

(TO-3)
Metal Can Package (TO-39)
Metal Can Package (TO-220)
Plastic Package

DS009062-30

DS009062-29
Case is Output
Bottom View
Case is Output Order Number LM117HVH,
Bottom View LM117HVH/883
Order Number LM117HVKSTL/883 or LM317HVH
See NS Package Number K02C See NS Package Number H03A
Order Number LM317HVK STEEL
See NS Package Number K02A

DS009062-31

Front View
Order Number LM317HVT
See NS Package Number T03B

www.national.com 12
 LM117HV/LM317HV
Physical Dimensions inches (millimeters) unless otherwise noted

Order Number LM117HVH, LM117HVH/883, or LM317HVH

NS Package Number H03A

Metal Can Package (K)

Order Number LM317HVK STEEL
NS Package Number K02A

13 www.national.com
LM117HV/LM317HV
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)

Metal Can Package (K)

Mil-Aero Product
Order Number LM117HVKSTL/883
NS Package Number K02C

Order Number LM317HVT

NS Package Number T03B

www.national.com 14
 LM117HV/LM317HV 3-Terminal Adjustable Regulator
Notes

LIFE SUPPORT POLICY

NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or 2. A critical component is any component of a life
systems which, (a) are intended for surgical implant support device or system whose failure to perform
into the body, or (b) support or sustain life, and can be reasonably expected to cause the failure of
whose failure to perform when properly used in the life support device or system, or to affect its
accordance with instructions for use provided in the safety or effectiveness.
labeling, can be reasonably expected to result in a
significant injury to the user.
National Semiconductor National Semiconductor National Semiconductor National Semiconductor
Corporation Europe Asia Pacific Customer Japan Ltd.
Americas Fax: +49 (0) 180-530 85 86 Response Group Tel: 81-3-5639-7560
Tel: 1-800-272-9959 Email: europe.support@nsc.com Tel: 65-2544466 Fax: 81-3-5639-7507
Fax: 1-800-737-7018 Deutsch Tel: +49 (0) 69 9508 6208 Fax: 65-2504466
Email: support@nsc.com English Tel: +44 (0) 870 24 0 2171 Email: ap.support@nsc.com
www.national.com Français Tel: +33 (0) 1 41 91 8790

National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.