AMS1117

1A Adjustable/Fixed Low Dropout Linear Regulator

General Description Key Features

The AMS1117-ADJ and AMS1117-1.2,-1.5,-1.8,-2.5,-2.85, - Low dropout voltage
-3.3 and-5 are low dropout three-terminal regulators with - Load regulation: 0.2% typical
1A output current capability. These devices have been - Optimized for Low Voltage
optimized for low voltage where transient response and - On-chip thermal limiting
minimum input voltage are critical. The 2.85V version is - Standard SOT-223 and TO-252 packages
designed specifically to be used in Active Terminators for - Three-terminal adjustable or fixed low dropout
SCSI bus. 1.2V,1.5V,1.8V, 2.5V, 2.85V, 3.3V, 5V. Regulators

On-chip thermal limiting provides protection against any

combination of overload and ambient temperatures that Applications
would create excessive junction temperatures.
- Active SCSI terminators
- High efficiency linear regulators
Unlike PNP type regulators where up to 10% of the output
- Post regulators for switching supplies
current is wasted as quiescent current, the quiescent cur-
rent of the AMS1117 flows into the load, increasing effi- - Battery chargers
ciency. - 12V to 5V linear regulators
-Motherboard clock supplies
The AMS1117 series regulators are available in the indus-
try-standard SOT-223 and TO-252 power packages.

Typical Application

Figure 1. Typical Applications of AMS1117

Notice: The distance between Vout pin and Capacitor should not exceed 4cm for excellent performance

1
Advanced Monolithic Systems http://www.ams-semitech.com
 AMS1117
1A Adjustable/Fixed Low Dropout Linear Regulator
Pin Assignments

Figure 2. Pin Assignments of AMS1117

*With package soldered to 0.5 square inch copper area over backside ground plane or internal power plane, ΘJA can vary from 30°C/W to
more than 50°C/W. Other mounting techniques may provide better thermal resistance than 30°C/W.

Absolute Maximum Ratings

Parameter Min. Max. Unit

VIN 18 V

(VIN – VOUT) * IOUT See Figure 3

Operating Junction Temperature Range -20 125 °C

Storage Temperature Range -65 150 °C

Lead Temperature (Soldering, 10 sec.) 300

°C

2
Advanced Monolithic Systems http://www.ams-semitech.com
 AMS1117
1A Adjustable/Fixed Low Dropout Linear Regulator
Block Diagram
VIN

Thermal
Limit

Current
Limit

VOUT

Substrate
GND (fixed output)
ADJ. (adjustable output)

Figure 3. Block Diagram of AMS1117

Electrical Characteristic
Typicals and limits appearing in normal type apply for TJ=25℃.Limits appearing in Boldface type apply over the entire junction temperature for
operation, -20℃to 125℃.

Min Typ Max

Symbol Parameter Conditions Units
(Note 2) (Note 1) (Note 2)

Reference AMS1117
VREF 1.225 1.250 1.275 V
Voltage 1.5V<=(VIN-VOUT)<=7V,10mA<=IOUT<=1A

IOUT = 10mA, VIN = 3.2V 1.176 1.200 1.224

V
AMS1117-1.2 ,2.7V<= VIN<=8.2V 1.152 1.200 1.248

AMS1117-1.5 ,3.0V<= VIN<=8.5V 1.470 1.500 1.530 V

AMS1117-1.8 ,3.3V<= VIN<=8.8V 1.764 1.800 1.836 V

10mA<=
VOUT Output Voltage AMS1117-2.5 ,4V<= VIN<= 9.5V 2.450 2.500 2.550 V
IOUT<=1A

AMS1117-2.85 , 4.35V <= VIN<= 9.85V 2.793 2.850 2.907 V

AMS1117-3.3 , 4.8V<= VIN <=10.3V 3.234 3.300 3.366 V

AMS1117-5.0,6.5V<=VIN <= 12V 4.900 5.000 5.100 V

3
Advanced Monolithic Systems http://www.ams-semitech.com
 AMS1117
1A Adjustable/Fixed Low Dropout Linear Regulator
Electrical Characteristic (Continued)
Typicals and limits appearing in normal type apply for TJ=25℃.Limits appearing in Boldface type apply over the entire junction temperature for
operation, -20℃ to 125℃.

Min Typ Max

Symbol Parameter Conditions Units
(Note 2) (Note 1) (Note 2)
Line Regultion
IOUT=10mA ,(VOUT+1.5V)<=VIN<=12V 0.035 0.2 %
(Note 3)

△VOUT VIN-VOUT=2V,10mA<= IOUT<=1A, 0.2 0.7 %

Load Regultion
AMS1117-1.2
(Note 3) 0.2 1 %
VIN-VOUT=2V,10mA<= IOUT<=1A,

VIN-VOUT Dropout Volage IOUT=1A,△VREF=1% 1.100 1.250 V

Current Limit VIN-VOUT= 2V, TJ=25℃ 1.1 1.5 A

Minimum Load AMS1117-ADJ

10 mA
Current (Note 4) 1.5V<=(VIN-VOUT)<=10V
Quiescent Curent VIN=VOUT+1.25V 5 13 mA

Thermal
TA = 25°C, 30ms pulse 0.01 0.1 %/W
Regulation
Ripple
f=120Hz,VIN-VOUT=3V, VRipple=1VPP 60 72 dB
ILimit Rejection

Adjust Pin Current 50 120 µA

Adjust Pin Current

1.5V<=VIN-VOUT<=7V, 10mA<=IOUT<=1A 0.2 5 µA
Change

Temperature
0.5 %
Stability
Long Term
TA = 125°C, 1000hrs. 0.3 %
Stability

4
Advanced Monolithic Systems http://www.ams-semitech.com
 AMS1117
1A Adjustable/Fixed Low Dropout Linear Regulator
Electrical Characteristic (Continued)
Typicals and limits appearing in normal type apply for TJ=25℃.Limits appearing in Boldface type apply over the entire junction temperature for
operation, -20℃to 125℃.

Min Typ Max

Symbol Parameter Conditions Units
(Note 2) (Note 1) (Note 2)
RMS Output Noise(% of
TA = 25°C, 10Hz<= f <=10kHz 0.003 %
VOUT)
Thermal Resistance, Junction SOT-223 15 ℃/W
ILimit to Case TO-252 3 ℃/W
Thermal Shutdown Junction Temperature 155 ℃
Thermal Shutdown Hysteresis 25 ℃
Note 1: Typical Values represent the most likely parametric norm.
Note 2: All limits are guaranteed by testing or statistical analysis.
Note 3: Load and line regulation are measured at constant junction room temperature.
Note 4: The minimum output current required to maintain regulation.

Typical Performance Characteristics

1.5
1.4
1.3
Dropout Voltage ( V )

1.2
1.0
0.9
0.8
0.7
0.6
0.5
0
0 0.2 0.4 0.6 0.8 1.0
Output Current ( A )

Figure 4. Dropout Voltage VS. Output Current

5
Advanced Monolithic Systems http://www.ams-semitech.com
 AMS1117
1A Adjustable/Fixed Low Dropout Linear Regulator

Typical Performance Characteristics (Continued)

0.260
3.70
1.255 3.65
1.250 3.60
ReferenceVoltage( V )

Output Voltage( V )
1.245 3.55
1.240 3.50

1.235 3.45
3.40
1.225
3.35
1.220
3.30
1.215 3.25
1.210 3.20
-75 –50 –25 0 25 50 75 100 125 150 175 -75 –50 –25 0 25 50 75 100 125 150 175
Junction Temperature ( ℃ ) Junction Temperature ( ℃ )

Figure 5. Reference Voltage VS. Temperature Figure 6. Output Voltage VS. Temperature

5 100
Note:
90 AMS1117 Only
Minimum Load Current( mA )

4 80
ADJ Pin Current( µA )

70
3 60
50
2 40
30
1 20
10
0 0
-75 –50 –25 0 25 50 75 100 125 150 175 -75 –50 –25 0 25 50 75 100 125 150 175
Junction Temperature ( ℃ )
Junction Temperature ( ℃ )

Figure 7. Minimum Load Current VS. Temperature Figure 8. ADJ Pin Current VS. Temperature

6
Advanced Monolithic Systems http://www.ams-semitech.com
 AMS1117
1A Adjustable/Fixed Low Dropout Linear Regulator
Mechanical Dimensions
4-Lead SOT-223 Package

Inches Millimeters
Symbol Notes
Min. Max. Min. Max.
A Ñ .071 Ñ 1.80

A1 Ñ .181 Ñ 4.80

B .025 .033 .064 .840

c Ñ 0.90 Ñ 2.29

D .248 .264 6.30 6.71

E .130 .148 3.30 3.71

e .115 .124 2.95 3.15

F .033 .041 .840 1.04

H .264 .287 6.71 7.29

I .0121 Ñ .310 Ñ

J Ñ 10° Ñ 10°
K 10° 16° 10° 16°
L .0008 .0040 .0203 .1018
M 10° 16° 10° 16°
N .010 .014 .250 .360

Figure 9. 4-Lead SOT-223 Package

7
Advanced Monolithic Systems http://www.ams-semitech.com
 AMS1117
1A Adjustable/Fixed Low Dropout Linear Regulator

Mechanical Dimensions (Continued)

3-Lead TO-252 Package

Notes:
Inches Millimeters 1. Dimensions are exclusive of mold flash, metal burrs
Symbol Notes or interlead protrusion.
Min. Max. Min. Max. 2. Stand off-height is measured from lead tip with ref. to
A .086 .094 2.19 2.39 Datum –B-.
3. Foot length is measured with ref. to Datum –A– with
b .025 .035 0.64 0.89
lead surface.
b2 .030 .045 0.76 1.14 4. Thermal pad contour optional within dimension b3
b3 .205 .215 5.12 5.46 4 and L3.
5. Formed leads to be planar with respect to one another
c .018 .024 0.46 0.61
at seating place –C-.
c2 .018 .023 0.46 0.58 6. Dimensions and tolerances.
D .210 .245 5.33 6.22 1
E .250 .265 6.35 6.73 1
e .090 BSC 2.29 BSC
H .370 .410 9.40 10.41
L .055 .070 1.40 1.78 3
L1 .108 REF 2.74 REF
L3 .035 .080 0.89 2.03 4
L4 .025 .040 0.64 1.02

Figure 10. 3-Lead TO-252 Package

8
Advanced Monolithic Systems http://www.ams-semitech.com
 AMS1117
1A Adjustable/Fixed Low Dropout Linear Regulator

Ordering Information

Package Temperature Range Part Number Output Voltage Packing Marking Transport Media

－２０℃ - +125℃　　　　　　　AMS1117-1.2 1.2V AMS1117 1.2 2.5K Tape and Reel

－２０℃ - +125℃　　　　　　　AMS1117-1.5 1.5V AMS1117 1.5 2.5K Tape and Reel

-20℃ - +125℃　　　　　　　AMS1117-1.8 1.8V AMS1117 1.8 2.5K Tape and Reel
-20℃ - +125℃　　　　　　　AMS1117-2.5 2.5V AMS1117 2.5 2.5K Tape and Reel
SOT－223
-20℃ - +125℃　　　　　　　AMS1117-2.85 2.85V AMS1117 2.8 2.5K Tape and Reel
-20℃ - +125℃　　　　　　　AMS1117-3.3 3.3V AMS1117 3.3 2.5K Tape and Reel
-20℃ - +125℃　　　　　　　AMS1117-5 5V AMS1117 5 2.5K Tape and Reel
-20℃ - +125℃　　　　　　　AMS1117 Adjust AMS1117 2.5K Tape and Reel
-20℃ - +125℃　　　　　　　AMS1117-1.2 1.2V AMS1117 1.2 2.5K Tape and Reel
-20℃ - +125℃　　　　　　　AMS1117-1.5 1.5V AMS1117 1.5 2.5K Tape and Reel
-20℃ - +125℃　　　　　　　AMS1117-1.8 1.8V AMS1117 1.8 2.5K Tape and Reel
-20℃ - +125℃　　　　　　　AMS1117-2.5 2.5V AMS1117 2.5 2.5K Tape and Reel
TO－252
-20℃ - +125℃　　　　　　　AMS1117-2.85 2.85V AMS1117 2.8 2.5K Tape and Reel
-20℃ - +125℃　　　　　　　AMS1117-3.3 3.3V AMS1117 3.3 2.5K Tape and Reel
-20℃ - +125℃　　　　　　　AMS1117-5 5.0V AMS1117 5 2.5K Tape and Reel
-20℃ - +125℃　　　　　　　AMS1117CD Adjust AMS1117CD 2.5K Tape and Reel

Advanced Monolithic Systems

http://www.ams-semitech.com
Disclaimer:
• AMS reserves the right to make changes to the information herein for the improvement of the design and performance
without further notice! Customers should obtain the latest relevant information before placing orders and should verify
that such information is complete and current.
• All semiconductor products malfunction or fail with some probability under special conditions. When using AMS products
in system design or complete machine manufacturing, it is the responsibility of the buyer to comply with the safety
standards strictly and take essential measures to avoid situations in which a malfunction or failure of such AMS products
could cause loss of body injury or damage to property.
• AMS will supply the best possible product for customers!

The " " logo is a registered trademark of Advanced Monolithic Systems.

All other company and product names are trademarks of their respective owners

9
Advanced Monolithic Systems http://www.ams-semitech.com