Apu8836 3
Apu8836 3
Typical Application
SD Enable EN Adj
Ordering information
These products are shipped on tape and reel, 3000 pieces per reel. The device is rated MSL3
for moisture sensitivity, and the reel is shipped sealed inside a moisture barrier bag.
Pin Configuration
APU8836Y5 Alternate Pin-out APU8836Y5R
TOP VIEW TOP VIEW
VIN GND EN EN GND VIN
SOT-23-5 SOT-23-5
Electrical Specifications
Unless otherwise specified, these specifications apply over C IN=CO=2.2F, IO=100uA, VIN(MIN)=2.5V, VOUT = VFB
V EN= 2V and TA=25oC. Typical values refer to T A=25oC.
Low duty cycle pulse testing is used to keep junction and case temperatures equal to the ambient temperature.
Note 1: Low duty cycle pulse testing with Kelvin connections is required in order to maintain accurate data.
Note 2: Dropout voltage is defined as the minimum differential voltage between VIN and VOUT required to maintain regulation at VOUT.
It is measured when the output voltage drops 1% below its nominal value.
Note 3: Ground current is the regulator quiescent current plus the pass transistor current. The total current from the supply is the sum
of the load current plus the ground pin current.
Gnd Ground pin. This pin must be connected to the lowest potential in the system and all
other pins must be at higher potential with respect to this pin.
En Enable pin. A low signal or left open on this pin shuts down the output. This pin must
be tied HI or to VIN for normal operation.
Adj A resistor divider from this pin to the VOUT pin and ground sets the output voltage. To
minimize the error due to the error amplifier, select the values of the resistor dividers
to be less than 10kΩ .
VOUT The output of the regulator. A capacitor with a minimum value of 2.2µF and max ESR
of 1Ω must be connected from this pin to ground to ensure stability.
Block Diagram
VIN VOUT
Adj
THERMAL
SHUTDOWN
+ CURRENT
0.8V
LIMIT
Gnd En
VOUT
VOUT
IOUT
IOUT
Power Sequence
Power ON (RL=16Ω) Power OFF (RL=16Ω)
VIN
VEN
VIN
VOUT
VEN
VOUT IOUT
IOUT
Power Sequence
Power ON (RL=8Ω) Power OFF (RL=8Ω)
VIN
VEN
VIN
VOUT
VEN
IOUT
VOUT
IOUT
VIN VIN
VEN
VEN
VOUT
VOUT IOUT
IOUT
VIN VIN
VEN
VEN
VOUT
IOUT
VOUT
IOUT
SYMBOLS Millimeters
MIN NOM MAX
A 1.00 1.10 1.30
A1 0.00 --- 0.10
A2 0.70 0.80 0.90
b 0.35 0.40 0.50
C 0.10 0.15 0.25
D 2.70 2.90 3.10
E 1.50 1.60 1.80
e --- 1.90(TYP) ---
H 2.60 2.80 3.00
L 0.37 --- ---
θ1 1° 5° 9°
e2 --- 0.95(TYP) ---
Note 1: Package body sizes exclude mold flash protrusions or gate burrs.
Note 2: Tolerance ± 0.1000 mm (4mil) unless otherwise specified.
Note 3: Coplanarity:0.1000 mm
Note 4: Dimension L is measured in gage plane.
Marking Information
Product: RS = APU8836Y5-HF-3TR
rS = APU8836Y5R-HF-3TR
RSSS
Date/lot code
For details of how to convert this
to standard YYWW date code format,
please contact us directly.