Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
83 views

How To Take An OSL Sample

This document provides instructions for taking luminescence dating samples from outcrops in 10 steps: 1) position the sampling tube at the target sediment; 2) pound the tube into the outcrop until full; 3) collect a sample for moisture content analysis; 4) collect surrounding sediment for dose rate analysis; 5) extract the full sampling tube; 6) cap and tape both ends of the tube; 7) label the tube and samples; 8) apply clear tape over the labels; 9) package the samples together for transport; and 10) record measurements like depth, location, and sediment observations.

Uploaded by

qzxv
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
83 views

How To Take An OSL Sample

This document provides instructions for taking luminescence dating samples from outcrops in 10 steps: 1) position the sampling tube at the target sediment; 2) pound the tube into the outcrop until full; 3) collect a sample for moisture content analysis; 4) collect surrounding sediment for dose rate analysis; 5) extract the full sampling tube; 6) cap and tape both ends of the tube; 7) label the tube and samples; 8) apply clear tape over the labels; 9) package the samples together for transport; and 10) record measurements like depth, location, and sediment observations.

Uploaded by

qzxv
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

HOW TO TAKE A SAMPLE FOR LUMINESCENCE DATING

Items to bring:
1. opaque metal conduit (DO NOT USE PVC)
purchased and cut at hardware store, 1.5” x 8”
ideally, may need end filed to sharpen
2. hammer to pound tube into outcrop
3. quart ziplock bags to collect dose-rate samples
4. film container (or other airtight) to collect
for water content
5. duct tape to cap sample tube
6. good luxuries = pounding caps (pipe ends),
styrofoam insulation plug in tube to prevent
mixing of sediment, plastic caps (Giddings core-
end caps), packing tape

Step 1: position
Target fine-medium sand with original sedimentary
structures, avoiding bioturbation and soils. If possible,
sample a thick unit, or at a point with relatively uniform
sediment within a foot radius. Also best if sample is
more than 1 m below the landform top to minimize
cosmogenic dose errors.
Place sharpened end of tube, with styrofoam plug, at
target point. Align tube at angle desired. Place
pounding cap over other end, using a round of duct tape
to hold it on during pounding.

Step 2: hammer
Pound sample tube into outcrop until you feel and
hear change indicating tube is full, or until tube is at
least flush with the outcrop face. Tube must be full and
packed tightly to avoid mixing during transport.
Step 3: moisture
Sample horizon for moisture content using an air-
tight container, such as a film canister. Fill completely.
Note evidence for ground or vadose water and describe
expected water content history of the sampled deposit.

Step 4: doserate
Sample for the environmental doserate into a 1-
quart ziplock freezer bag. Representatively capture
sediment from ~1 foot radius surrounding the sample,
being particularly complete nearer the tube. This effort
also provides headway towards digging out the sample
tube from cohesive sediment. Fill bag half full or more.

Step 5: extract tube


At some point before the tube falls out of its own
accord, stop excavating around it and gently turn tube
to loosen and extract. With open end of tube carefully
pointed up, pack any extra space with more sediment,
tamping it down lightly. Material at the ends of the
sampling tubes is discarded in the lab. If greater than 1
cm needs to be added, lay a strip of duct tape in to mark
beginning of sample before filling and tamping, record
this on sample sheet and notes.

Step 6: cap and tape


Place cap on end and tape both vertically and
horzontally with at least two layers of duct tape. Turn
tube over, remove pounding cap, fill and tamp if
necessary, cap and tape again.
Step 7: label
Mark tube, moisture sample, and doserate bag with
sharpie. Give samples individual labels, relatively
simple in scheme, that relate to your specific project.

Step 8: tape
Consider putting clear packaging tape over tube and
baggie labels to protect marker from wearing off and
becoming indecipherable.

Step 9: package
Also consider throwing the tube, moisture, and dose
rate sample components into a separate large ziplock
baggie for orderly transport.

Step 10: measurements


Stratigraphic context is important, of course. Depth
of burial below the landform surface is needed to
calculate cosmic doserate. If there has been recent
erosion or excavation, estimate the original depth. If
the sample was collected from a deposit indicating
incremental accumulation and burial, make notes of the
depth and significance of buried soils-surfaces.
Record the latitude, longitude, and elevation of the
sample, also for calculation of the cosmic doserate.
Finally, record any other sedimentological
observations of possible interest.

You might also like