References PDF

References
ACI Committee 302, Guide for Concrete Floor and Slab Construction, ACI 302.1R
96, American Concrete Institute, Detroit, MI, 1996.
Ad Hoc Committee 1986, Serviceability: A critical appraisal and research needs,
Journal of Structural Engineering, ASCE, vol. 112, no. 12, pp. 264664.
Adeli, H. 1988, Interactive Microcomputer-Aided Structural Steel Design, Prentice-
Hall, Englewood Cliffs, NJ.
Adluri, S.M.R. and M.K.S Madugula 1996, Development of column curves for single
angles, Journal of Structural Engineering, vol. 122, no. 3, pp. 31825.
Agarval, K.M. and A.P. Stafiej 1980, Calculation of effective length of stepped columns,
Engineering Journal, AISC, 1980, no. 4, pp. 96105.
Agerskov, H. 1979, High strength bolted connection subject to prying, Journal of
Structural Division, ASCE, vol. 102, no. ST1, pp. 161-175.
Agerskov, H. 2000, Fatigue in steel structures under random loading, Journal of
Constructional Steel Research, vol. 53, no. 3, pp. 283305.
AISC 809-97, Torsional Analysis of Steel Members, American Institute of Steel
Construction, Design Guide 9, Chicago, IL.
AISC 1993, Specification for Load and Resistance Factor Design of Singleangle
Members, American Institute of Steel Construction, Chicago, IL.
AISC 805-1991, Design of Low- and Medium-rise Steel Buildings, Design Guide 5,
American Institute of Steel Construction, Chicago, IL.
AISC 807-2004, Industrial Buildings: Roofs to Anchor Rods, 2nd edn, Design Guide 7,
AISC 810-1997, Erection Bracing of Low-rise Structural Steel Frames, Design Guide
10, American Institute of Steel Construction, Chicago, IL.
AISC 814-2002, Staggered Truss Framing Systems, Design Guide 14, American Institute
of Steel Construction, Chicago, IL.
AISC 819-2003, Fire Resistance of Structural Steel Framing, Design Guide 19,
AISC 325-05, Manual of Steel Construction, 13th edn, American Institute of Steel
Construction, Chicago.
AISC-LRFD 1999, Load and Resistance Factor Design Specification for Structural
Steel Buildings, American Institute of Steel Construction, Chicago, IL.
Alinia, M.M. and M. Dastfan 2006, Behaviour of thin plate shear walls regarding frame
members, Journal of Constructional Steel Research, vol. 62, pp. 7308.
R.2 Design of Steel Structures
Allen, D. 1978, MerchantRankine approach to member stability, Journal of Structural

Div., ASCE, vol. 104, no. ST12, pp. 190414.
Allen, D.E. 1972, Structural Safety, Division of Building Research, National Research
Council of Canada (CBD 147), Ottawa.
Allen, D.E. 1990, Building vibration from human activities, Concrete International,
vol. 12, no. 6, pp. 6673.
Allen, D.E. and T.M. Murray 1993, Design criteria for vibration due to walking,
Engineering Journal, AISC, vol. 30, no. 4, pp.11729.
Allen, E. and J. Iano 2001, The Architects Studio Companion: Rules of Thumb for
Preliminary Design, 3rd edn, John Wiley, NY, p. 416.
Allen, H.G. and P.S. Bulson 1980, Background to Buckling, McGraw-Hill, London, p.
582.
Alpsten, G.A. 1973, Variation in Mechanical and Cross-sectional Properties of Steel,
Swedish Institute of Steel Construction, no. 42.
Althouse, A.D., C.H. Turnquist, W. Bowditch, and K.E. Bowtich 2000, Modern Welding,
9th edn, The Good Heart-Willcox, IL, p. 779.
Ambrose, J. and D. Vergun 1995, Simplified Building Design for Wind and Earthquake
Forces, 3rd edn, Wiley-InterScience, NY, p. 368.
Aminmansour, A. 2004, Steel beam-column design: new, fast and practical approach,
Practice Periodical on Structural Design and Construction, ASCE, vol. 9, no. 2,
pp. 937.
Anderson, J.P., and J.H. Woodward 1972, Calculation of effective lengths and effective
slenderness ratios of stepped columns, Engineering Journal, AISC, vol. 9, no. 4,
pp. 15766.
ANSI/AISC 341-2005, Seismic Provisions for Structural Steel Buildings, American
Institute of Steel Construction, Chicago, IL, p. 333.
ANSI/AISC 360-2005, Specification for Structural Steel Buildings, American Institute
of Steel Construction, Chicago, IL, www.aisc.org, 25th July 06.
ANSI/ASCE 10-90, Design of Latticed Steel Transmission Structures, ASCE, NY, 1992.
ANSI/ASCE 8-90, Specification for the Design of Cold-formed Stainless Steel Structural
Members, ASCE, NY, 1991.
Arnold, C., and R. Reitherman 1982, Building Configuration and Seismic Design, John
Wiley, p. 310.
Arthi, N., S. Arul Jayachandran, and S. Seetharaman 2002, Numerical Analysis of
Semi-rigid Sway Frames using GaussSeidel Iterations, All India Seminar on
Modern Trends in Steel Structures, ACCE (I) and IE (I), Nagpur, February 8-9, pp.
5765.
Arul Jayachandran, S., S. Seetharaman, and I.V.K. Kishore 2004, Semi-rigid connections
in steel framesA note for the designers of structural steelwork, Steel in
Construction, INSDAG, vol. 5, no. 1, pp. 5763.
Arya, A.S. and J.L. Ajmani 1989, Design of Steel Structures, 4th edn, Nem Chand and
Bros, Roorkee, Uttaranchal, India, pp. 587609.
AS 4100-1998, Australian Standards-Steel Structures, Standards Association of
Australia, The Crescent, Homebush, NSW 2140.
ASCE Manual 1988, Guide for Design of Steel Transmission Towers, American Society
of Civil Engineers, Second ed., no. 52.
References R.3
ASCE Task Committee 1992, Design criteria for composite structures in steel and
concrete: Proposed specification for structural steel beams with web openings,
Journal of Structural Engineering, vol. 118, no. ST12, pp. 331549.
ASCE Technical Committee/SEI 1997, LRFD: Effective length and notional load
approaches for assessing frame stability: Implications for American steel design,
American Society of Civil Engineers, Reston,VA, p. 442.
ASCE/SEI/SFPE 29-99, Standard Calculation Methods for Structural Fire Protection,
2003, ASCE Press, Reston, VA, p. 72.
Astaneh-Asl, A. and Q. Zhao 2002, Cyclic Test of Steel Shear Walls, Final Report,
Dept. of Civil and Environmental Engg., University of California, Berkeley.
Astanesh, A. 1985, Procedure for design and analysis of hanger type connections,
Engineering Journal, AISC, vol. 22, pp. 636.
Astanesh, A., S.M. Call, and K.M. McMullin 1989, Design of single plate shear
connections, Engineering Journal, AISC, vol. 26, no. 1, pp. 2132 (also see
Discussion by R.M. Richard 1990, vol. 27, no. 3, pp. 121126).
Attala, M.N., G.G. Deierlein, and W. McGuire 1994, Spread of plasticity: Quasi-plastic
hinge approach, Journal of Structural Engineering, ASCE, vol. 120, no. 8, pp.
245173.
Austin, W.J. 1961, Strength and design of metal beamcolumns, Journal of the
Structural Div., ASCE, vol. 87, no. ST4, pp. 134.
Ayrton, W.E. and J. Perry 1866, On Struts, The Engineer, vol. 62, p. 464.
Bahia, C.S. and L.H. Martin 1981, Experiments on stressed and unstressed bolt groups
subject to torsion and shear, Proc. Conference of Joints in Structural Steelwork,
Teeside Polytechnic, UK.
Bailey, C.G. 2006, Advances in fire engineering design of steel structures, Proc.
Institution of Civil Engineers on Structures and Buildings, UK, vol. 159, issue 1,
pp. 2135.
Bakota, J.F. 1977, Mill building design procedure, Engineering Journal, AISC, vol.
14, pp. 1307.
Ballio, G. and C. Castiglioni 1995, A unified approach for the design of steel structures
under low and high cycles fatigue, Journal of Constructional Steel Research, vol.
34, pp. 75101.
Ballio, G. and F.M. Mazzolani 1983, Theory and Design of Steel Structures, Chapman
and Hall, London, pp. 505-506 (see also p. 632).
Bangash, M.Y.H. 2000, Structural Detailing in Steel, Thomas Telford, London, p. 240.
Bannantine, J.A., J.J. Comer, and J.L. Handrock 1990, Fundamentals of Metal Fatigue
Analysis, Prentice-Hall, Englewood Cliffs, NJ.
Barakat, M. and W.F. Chen 1990, Practical analysis of semi-rigid frames, Engineering
Journal, AISC, vol. 27, no. 2, pp. 5468.
Barker, M.G., A.M. Hurst, and D.W. White 2002, Tension field action in hybrid steel
girders, Engineering Journal, AISC, vol. 39, no.1, pp. 5262.
Barsom, J.M. and S.T. Rolfe 1999, Fatigue and Fracture Control in Structures:
Application of Fracture Mechanics, American Society for Testing Materials
(ASTM), USA.
Barth, K.E., J.G. Orbison, and R. Nukala 2002, Behaviour of steel tension members
subjected to uniaxial loading, Journal of Constructional Steel Research, vol. 58,
pp. 110320.
Basler, K. 1961, Strength of plate girders in shear, Journal of the Structural Div.,
Proc. ASCE, vol. 87, no. ST7, pp. 151180.
Basler, K. 1963, Strength of plate girders under combined bending and shear-Part II,
Transactions, ASCE, vol. 128, pp. 72035.
Basler, K. and B. Thürlimann 1963, Strength of plate girders in bending-Part II,
Bathon, L., W.H. Mueller III, and L. Kempner Jr. 1993, Ultimate load capacity of
single steel angles, Journal of Structural Engineering, ASCE, vol. 119, no. 1, pp.
279300.
Bazant, Z.P. and D.M. Frangopal 2002, Size effect hidden in excessive dead load factor,
Journal of Structural Engineering, vol. 128, no. 1, pp. 8086.
Becker, R. 1995, Seismic Design of Special Concentrically Braced Frames, Structural
Steel Education Council, Morga, CA.
Becker, R. and M. Ishler 1996, Seismic Design Practice for Eccentrically Braced Frames,
Structural Steel Education Council, Morga, CA.
Beedle, L.S. 1958, Plastic Design of Steel Frames, John Wiley & Sons, NY.
Beer, H. and G. Schultz 1970, Theoretical basis of the European column curves,
Construction Metallique, no. 3, pp. 3757.
Berman, J.W. and M. Bruneau 2004, Steel plate shear walls are not plate girders,
Engineering Journal, AISC, vol. 41, no. 3, pp. 95106.
Bhandari, N.M., P. Krishna, K. Kumar, and A. Gupta 2004, An Explanatory Hand book
on IS: 875 (Part 3) Wind Loads on Buildings and Structures, Dept. of Civil Engg.,
IIT Kanpur, p. 116, http://www.iitk.ac.in/nicee/IITK-GSDMA/W06.pdf, 20 March
2006.
Billington, D.P. 1983, The Tower and the Bridge, The New Art of Structural Engineering,
Princeton University Press, Princeton, NJ.
Bjorhovde, R. 1972, Deterministic and Probabilistic Approaches to the Strength of
Steel Columns, Ph D Dissertation, Lehigh University, Bethlehem, PA.
Bjorhovde, R. 1985, Effect of end restraint on column strength-practical applications,
Engineering Journal, AISC, vol. 21, no.1, pp. 4245.
Bjorhovde, R. and L. Tall 1971, The probabilistic characteristics of maximum column
strength, Proc. of the International Colloquium on Column Strength, Paris, pp.
2334.
Bjorhovde, R., A. Colson, and J. Brozzetti 1990, Classification system for beam-to-
column connections, Journal of Structural Engineering, ASCE, vol. 116, no. 11,
pp. 305976.
Bjorhovde, R., T.V. Galambos, and M.K. Ravindra 1978, LRFD criteria for steel beam
columns, Journal of the Structural Div., ASCE, vol. 104, no. ST9, pp. 137187.
Bleich, F. 1952, Buckling Strength of Metal Structures, McGraw Hill, NY.
Blodgett, O.W. 1966, Design of Welded Structures, The James P. Lincoln Arc Welding
Foundation, Cleveland, Ohio.
Boissonnade, N., J.P. Jaspart, J.P. Muzeau, and M. Villette 2002, Improvement of the
interaction formulae for beam-columns in Eurocode 3, Computers and Structures,
vol. 80, pp. 237585.
Boissonnade, N., J.P. Jaspart, J.P. Muzeau, and M. Villette 2004, New interaction
formulae for beam-columns in Eurocode 3: The FrenchBelgian approach, Journal
of Constructional Steel Research, vol. 60, pp. 42131.
References R.5
Bond, G.V.L. 1975, Fire and Steel Construction: Water Filled Hollow Columns,
Constrado, UK.
Borcherdt, R. 1994, Estimates of site dependent response spectra for design
(methodology and justification), Earthquake Spectra, vol.10, no. 4, pp. 61753.
Bowles, J.E. 1980, Structural Steel Design, McGraw Hill, NY, pp. 21753.
Bowles, J.E. 1995, Foundation Analysis and Design, 5th edn, McGraw Hill, NY.
Bozorgnia, Y. and V.V. Bertero 2004, Earthquake Engineering: From Engineering
Seismology to Performance-based Engineering, CRC Press, Boca Raton, Florida,
p. 1152.
Bradford, M.A. 1988, Stability of tapered I-beams, Journal of Constructional Steel
Research, vol. 9, pp. 195216.
Bradford, M.A. 1989, Inelastic buckling of tapered mono-symmetric I-beams,
Engineering Structures, vol. 11, no. 2, pp. 11926.
Bradford, M.A. 1992, Lateral-distorsional buckling of steel I-section members, Journal
of Constructional Steel Research, vol. 23, no. 13, pp. 97116.
Bradford, M.A. and D.J. Oehlers 2000, Elemental Behaviour of Composite Steel and
Concrete Structural Elements, ButterworthsHeinemann, London, p. 280.
Bradford, M.A. and N.S. Trahair 1981, Distortional buckling of I-beams, Journal of
Bradford, M.A. and P.E. Cuk 1988, Elastic buckling of tapered mono-symmetric I-
beams, Journal of Structural Engineering, ASCE, vol. 114, no. 5, pp. 977996.
Bradford, M.A. and Y.L. Pi 2006, Flexural torsional buckling of fixed arches under
uniform bending, Journal of Constructional Steel Research, vol. 62, no. 1-2, pp.
2026.
Bradford, M.A., P.E. Cuk, Gizejowski, and N.S. Trahair 1987, Inelastic lateral buckling
of beam-columns, Journal of Structural Engineering, ASCE, vol. 113, no. 11, pp.
225977.
BRE Digest 317-1986, Fire Resistant Steel Structures: Free Standing Blockwork Filled
Columns and Stanchions, Building Research Establishment, UK.
Bridge, R.Q. and D.J. Fraser 1987, Improved G-factor method for evaluating effective
lengths of columns, Journal of Structural Engineering, ASCE, vol. 113, no. 6, pp.
134156.
British Steel 1996, The Prevention of Corrosion on Structural Steelwork, British Steel
Corporation, Swinden, UK.
Brockenbrough, R.L. and F.S. Merritt 2006, Structural Steel Designers Handbook, 4th
edn, McGraw Hill, p. 800.
Brockmann, W. and T. Neeb 2001, Stand der klebtechnik im stahlbau, Der Stahlbau,
vol. 70, no. 2, pp. 10615.
Brown, C.B. and X. Yin 1998, Errors in structural engineering, Journal of Structural
Engineering, ASCE, vol. 114, no. 11, pp. 257593.
Brown, D.G. 1995, Modeling of Steel Structures for Computer Analysis, The Steel
Construction Institute, Ascot, UK, p. 52.
Bruneau, M., C.M. Uang, and A. Whittaker 1997, Ductile Design of Steel Structures,
McGraw Hill, NY, p. 485.
BS 476-1987, Fire Tests On Building Materials And StructuresPart 8: Test Methods
And Criteria for the Fire Resistance of Elements of Building Construction; Part
20: Methods for the Determination of the Fire Resistance of Elements of

Construction (General Principles); Part 21: Methods for the Determination of the
Fire Resistance of Load Bearing Elements of Constructions, British Standards
Institution, London, 1987.
BS 5950-1990, Structural Use of Steelwork in BuildingsPart 8: Code of Practice for
Fire Resistant Design, British Standards Institution, London, 1990.
BS 5950-2000, Structural Use of Steelwork in BuildingsPart 1: Code of Practice for
Design in Simple and Continuous ConstructionHot Rolled Section, British
Standards Institution, London, 2000, p. 213.
Buchanan, A.H. 2001, Structural Design for Fire Safety, John Wiley, Chichester, England,
p. 421.
Buchanan, R.A. 1972, Industrial Archeology in Britain, Penguin, London.
Burgett, L.B. 1973, Selection of a trial column section, Engineering Journal, AISC,
vol. 10, no. 2, pp. 549.
Burton, H.S. 1995, Proposed specifications for structural steel beams with web
openings, Journal of Structural Engineering, ASCE, vol. 121, no. 3, pp. 58997.
Bushev, V.P., et al. 1975, Fire Resistance of Buildings, Amerind Publishing Co. Pvt.
Ltd., New Delhi.
Butler, L.J., S. Pal, and G.L. Kulak 1972, Eccentrically loaded welded connections,
Journal of Structural Div., ASCE, vol. 98, no. ST5, pp. 9891005.
Byers, W.G., M.J. Marley, J. Mohammadi, R.J. Nielson, and S. Sarkani 1997, Fatigue
reliability reassessment procedures: State of the art paper, Journal of Structural
Byfield, M.P. 1997, Material and geometric properties of structural steel for use in
design, The Structural Engineer, vol. 75, pp. 3637.
Cabrero, J.M. and E. Bayo 2005, Development of practical design methods for steel
structures with semi-rigid connections, Engineering Structures, vol. 27, no. 8, pp.
11251302.
Caccese, V., M. Elgaaly, and R. Chen 1993, Experimental study of thin steel plate
shear walls under cyclic load and post buckling of steel plate shear walls under
cyclic loads, Journal of Structural Engineering, ASCE, vol. 119, no. 2, pp. 573
605.
Camfield, F. 1980, Tsunami Engineering, Coastal Engineering Research Center, US
Army Corps of Engineers, Special Report (SR-6), p. 222.
Camp, C.V. and B.J. Bichon 2004, Design of space trusses using ant colony
optimization, Journal of Structural Engg., ASCE, vol. 130, no. 5, pp. 74151.
CAN/CSA-S16.1M01, Limit States Design of Steel Structures, Canadian Standards
Association, Rexdale (Toronto), Ontario, Canada, 2001.
Causes and Prevention of Lamellar Tearing 1982, Civil Engineering, ASCE, vol. 52,
no. 4, pp. 74-75.
Chakraborty, G. and T.K. Bandyopadhyay 2005, Methods and Codal Provision for
Passive Fire Protection of Steel Structures, New Building Materials and
Construction World, vol. 10, No. 11, pp. 11020.
Chan, S.L. and P.P.T. Chui 2000, Non-linear Static and Cyclic Analysis of Steel Frames
with Semi-rigid Connections, Elsevier, UK.
References R.7
Chaudhari, B. and A.K. Samanta 2003, Corrosion Protection of Steel Structures by

Thermal Spraying, Course on proposed revision of IS: 800, Institute for steel
development and growth (INSDAG), Chennai, December 19-20, pp. 14.111.
Chen, M.T. and D.E. Jolissaint Jr. 1983, Pure and warping torsion analysis of rigid
frames, Journal of Structural Engineering, ASCE, vol. 109, no. 8, pp. 1999
2003.
Chen, W.F. (ed.) 1987, Joint flexibility in steel frames, Journal of Constructional
Steel Research, Special Issue, vol. 8.
Chen, W.F. (ed.) 1988, Steel beam-to-column building connections, Journal of
Constructional Steel Research, Special Issue, vol. 10.
Chen, W.F. 1971, Further studies of inelastic beam-column-problem, Journal of the
Chen, W.F. and D.E. Newlin 1973, Column web strength in beam-to-column
connections, Journal of the Structural Div., ASCE, vol. 99, no. ST9, pp.1978-
1984.
Chen, W.F. and E.M. Lui (eds) 2005, Handbook of Structural Engineering, 2nd edn,
CRC Press, Boca Raton, Florida, p. 1768.
Chen, W.F. and E.M. Lui 1986, Stability design criteria for steel members and frames
in the United States and discussion by Vandepitte, Journal of Constructional Steel
Research, vol. 5 & 6, no. 1, pp. 3174, pp. 769.
Chen, W.F. and E.M. Lui 1987, Structural Stability: Theory and Implementations,
Elsevier, NY.
Chen, W.F. and E.M. Lui 1991, Stability Design of Steel Frames, CRC Press, Boca
Raton, Florida, p. 380.
Chen, W.F. and I.S. Sohal 1995, Plastic Design and Second-order Analysis of Steel
Frames, SpringerVerlag, NY.
Chen, W.F. and K.V. Patel 1981, Static behaviour of beam-to-column moment
connections, Journal of the Structural Div., ASCE, vol. 107, no. ST9, pp. 1815
39.
Chen, W.F. and N. Kishi 1989, Semi-rigid steel beam-to-column connections: Database
and modeling, Journal of Structural Engineering, ASCE, vol. 115, no. 1, pp. 105
19.
Chen, W.F. and S. Santathadaporn 1968, Review of column behavior under biaxial
loading, Journal of the Structural Div., ASCE, vol. 94, no. ST12, pp. 29993021.
Chen, W.F. and S. Toma (eds) 1994, Advanced Analysis of Steel Frames: Theory,
Software and Applications, CRC Press, Boca Raton, NY, p. 400.
Chen, W.F. and S. Zhou 1987, Cm factor in load and resistance factor design, Journal
of Structural Engineering, ASCE, vol. 113, no. 8, pp. 173854.
Chen, W.F. and S.E. Kim 1997, LRFD Steel Design using Advanced Analysis, CRC
Press, Boca Raton, NY, p. 441.
Chen, W.F. and T. Atsuta 1976, Theory of BeamColumnsvol. I: In-plane Behavior
and Design, McGraw Hill, NY.
Chen, W.F. and T. Atsuta 1977, Theory of BeamColumnsvol. II: Space Behavior
and Design, McGraw Hill, NY.
Chen, W.F., Y. Goto, and J.Y.R. Liew 1995, Stability Design of Semi-rigid Frames,
John Wiley, NY, p. 488.
Chen, X. and A. Kareem 2004, Equivalent static wind loads on buildings: New model,
Cheng, J.J.R. 1993, Design of steel beams with end copes, Journal of Constructional
Steel Research, vol. 25, no. 1-2, pp. 322.
Cheng, J.J.R., G.Y. Grondin, and M.C.H. Yam 2000, Design and Behaviour of Gusset
Plate Connections, Fourth International Workshop on Connections in Steel
Structures, Roanoke, VA, USA, October 2225, pp. 307317.
CheongSiatMoy 1974, General Analysis of laterally loaded beam-columns, Journal
of the Structural Div., ASCE, vol. 100, no. ST6, pp. 126378 (also May 1974, pp.
95370).
CheongSiatMoy 1999, An improved K-factor formula, Journal of Structural
Engineering, vol. 125, no. 2, pp. 169174.
Chern, C. and A. Ostapenko 1971, Strength of Longitudinally Stiffened Plate Girders
under Combined Loads, IABSE Colloquium on Design of Plate and Box Girders
for Ultimate Strength, London.
Chesson Jr, E., N.L. Faustino, and W.H. Munse 1965, High strength bolts subject to
tension and shear, Journal of the Structural Div., ASCE, vol. 91, no. ST5, pp.
15580.
Chopra, A.K. 2000, Dynamics of Structures: Theory and Applications to Earthquake
Engineering, 2nd edn, Prentice-Hall, Englewood Cliffs, NJ, p. 844.
Christopher, J.E. and R. Bjorhovde 1999, Semi-rigid frame design methods for practicing
engineers, Engineering Journal, AISC, 1st qtr, vol. 36, pp. 1228.
Chu, K.H. and H.L. Chow 1969, Effective column length in unsymmetrical frames,
Publication of IABSE, pp. 2941.
City and County of Honolulu Building Code, Department of Planning and Permitting of
Honolulu, Hawaii, Chapter 16 Article 11, July 2000.
Clark, J.W. and H.N. Hill 1960, Lateral buckling of beams, Journal of the Structural
Clarke, A.B. and S.H. Coverman 1987, Structural Steelwork Limit State Design,
Chapman and Hall, London, p. 282.
Clarke, M.J., W.F. Chen, and S. Toma (eds) 1994, Plastic-zone Analysis of Frames
Chapter 6 of Advance Analysis of Steel Frames: Theory, Software and Applications,
CRC Press, Boca Raton, Florida, pp. 259319.
Clough, R.W. and J. Penzien 1993, Dynamics of Structures, McGraw Hill, NY.
Coates, R.C., M.G. Coutie, and F.K. Kong 1988, Structural Analysis, Van Nostrand
Reinhold, NY, pp. 12731.
Cochrane, V.H. 1922, Rules for rivet hole deductions in tension members, Engineering
News Record, vol. 89, pp. 847-48.
Colombi, P. 2006, The ponding problem on flat steel roof grids, Journal of the
Constructional Steel Research, vol. 62, no.7, pp. 64755.
Comite Euro-International du Beton 1994, Fastenings to Concrete and Masonry
Structures, State-of-the-art Report, Thomas Telford, UK, p. 249.
Commentary on Highly Restrained Welded Connections 1973, Engineering Journal,
American Institute of Steel Construction, vol. 10, no. 3, 3rd qtr, pp. 6173.
Cook, N. 2002, Wind Loading: A Practical Guide to BS 6399-2, Thomas Telford,
London, p. 150.
References R.9
Cook, N.J. 1985, The Designers Guide to Wind Loading of Building StructuresPart
I, Butterworths, London.
Cook, R.A. 1999, Strength Design of Anchorage to Concrete, Portland Cement
Association, Skokie, IL, p. 86.
Cooper, P.B. 1967, Strength of longitudinally stiffened plate girders, Journal of the
Cooper, P.B. 1971, The Ultimate Bending Moment for Plate Girders, IABSE
Colloquium on Design of Plate and Box Girders for Ultimate Strength, London.
Corrosion 1987, Metals handbook, American Society for Metals International, Metals
park, vol. 13, OH.
Coulbourne, W.L., E.S. Tezak, and T.P. McAllister 2002, Design guidelines for
community shelters for extreme wind events, Journal of Architectural Engineering,
ASCE, vol. 8, no. 2, pp. 6977.
Crawford, S.F. and G.L. Kulak 1971, Eccentrically loaded bolted connections, Journal
of the Structural Div., ASCE, vol. 97, no. ST3, pp. 76583.
CSIRO 1993, Firecalc, Division of Building Construction and Engineering, CSIRO
North Ryde, NSW, Australia.
Culver, C.G. 1966, Exact solution of biaxial bending equations, Journal of the
Dafedar, J.B., Y.M. Desai, and M.R. Shiyekar 2001, Review of code provisions for
effective length of framed columns, The Indian Concrete Journal, vol. 75, no. 6,
pp. 4027.
Dames & Moore 1980, Design and Construction Standards for Residential Construction
in Tsunami-Prone Areas in Hawaii, Prepared for the Federal Emergency
Management Agency, USA.
Darwin, D. 1990, Design of Steel and Composite Beams with Web Openings (with
companion computer program WEBOPEN)AISC 802-90 Steel Design Guide
No. 2, American Institute of Steel Construction, Chicago, IL.
Davies, J.M. 1976, Calculation of steel diaphragm behaviour, Journal of the Structural
Davies, J.M. and B.A. Brown 1996, Plastic Design to BS 5950, Blackwell Science,
Oxford, England.
Davies, J.M. and E.R. Bryan 1982, Manual of Stressed Skin Diaphragm Design, Granada,
NY.
Davison, B., and G.W. Owens 2004, Steel Designers Manual, 6th edn, The Steel
Construction Institute, Blackwell Publishers, Ascot, London.
Davison, J.B., P.A. Kirby, and D.A. Nethercot 1987, Rotational stiffness characteristics
of steel beam-to-column connections, Journal of Constructional Steel Research,
vol. 8, pp. 1754.
Dawe, J.L. and G.L. Kulak 1974, Welded connections under combined shear and
moment, Journal of the Structural Div., ASCE, vol. 100, no. ST4, pp. 72741.
Day, R.W. 2006, Foundation Engineering Handbook, McGrawHill, NY/ASCE Press,
p. 930.
Dayaratnam, P. 1996, Design of Steel Structures, 2nd edn, Wheeler Publishing,
Allahabad, p. 868.
Deepti, C.E., M.G. Stewart, and D.V. Rosowsky 2002, Structural reliability of multi-
storey buildings during construction, Journal of Structural Engineering, vol. 128,
no. 2, pp. 20513.
DeLuca, A., F.M. Mazzolani, and V. Piluso 1991, Stability of Columns and Beam
Columns: Eurocode 3 vs. Other Codes, International Conf. on Steel and Aluminium
Structures, Singapore, May 2224, pp. 28897.
Derry, T.K. and T. Williams 1960, A Short History of Technology, Oxford University
Press, Oxford, U.K.
Detailing for Steel Construction 2002, 2nd edn, American Institute for Steel Construction,
(AISC 326-02) Chicago, IL.
Devenport, A.G. 1960, Wind Loads on Structures, Division of Building Research, Tech.
Paper 88, National Research Council of Canada.
DeWolf, J.T. and D.T. Ricker 2006, Column Base Plates, 2nd edn, (AISC 801-06) Steel
Design Guide Series no. 1, AISC, Chicago, IL.
DeWolf, J.T. and E.F. Sarisley 1980, Column base plates with axial loads and moments,
Journal of the Structural Div., ASCE, vol. 106, pp. 216784.
Dexter, R.J. and L.W. Lu 2002, The effects of a severe fire on the steel frame of an
office building, Engineering Journal, AISC, vol. 38, no. 4, pp. 16775.
Dexter, R.J. and S.A. Altstadt 2003, Strength and ductility of tension flanges in girders,
A.A. Balkema, Mahmoud, K.M. (ed.), Sweto & Zeitlinger, Lisse, The Netherlands,
pp. 6781.
Dhillon, B.S. and J.W. OMalley III 1999, Interactive design of semi-rigid steel frames,
Diaphragm Design Manual 1995, Steel Deck Institute, Fox River Grove, IL.
DIN 18230-1, Baulicher Brandschutz Im Industrialbau, Teil 1 (Structural Fire Protection
In Industrial Buildings Part 1: Analytically Required Fire Resistance Time),
Deutsches Institute Fuer Normung E.V., Berlin, 1996.
DIN 18800, Teil 2Stahlbauten: Stabilitätsfälle, Knicken von Stäben und Stabwerben,,
Deutsches Institut fur Normung E.V., Berlin, 1980.
Disque, R.O. 1973, Inelastic K-factor for column design, Engineering Journal, AISC,
vol. 10, no. 2, 2nd qtr, pp. 3335.
Donnelly, J.A. 1968, Determining the cost of welded joints, Engineering Journal,
AISC, vol. 5, no. 4, pp. 146-47.
Douty, R.T. and W. McGuire 1965, High strength bolted moment connections, Journal
Dowling, P.J., P. Knowles, and G.W. Owens 1988, Structural Steel Design, The Steel
Construction Institute, Butterworths, London, p. 399.
Downing, S.D. and D.F. Socie 1982, Simple rainflow counting algorithms, International
Journal of Fatigue, vol. 4, no. 1, pp. 3140.
Dowrick, D. 2003, Earthquake Risk Reduction, John Wiley, Chichester, England, UK.
Dowswell, B. 2004, Lateral-torsional buckling of wide-flange cantilever beams,
Engineering Journal, AISC, vol. 41, no. 3.
Dowswell, B. and S. Barber 2005, Shear Lag in Rectangular Hollow Structural Sections
Tension Members: Comparison of Design Equations to Test Data, Practice
Periodical on Structural Design and Construction, ASCE, vol. 10, no. 3, pp. 195
9.
References R.11
Drake, R.M. and S.J. Elkin 1999, Beam-column base-plate design: LRFD method,
Engineering Journal, AISC, vol. 36, no. 1, pp. 2938, Discussion by Doyle, J.M.,
and Fisher, J.M., vol. 42, no. 4, 2005, pp. 273-274.
Driscoll, G.C. 1976, Effective length of columns with semi-rigid connections,
Engineering Journal, AISC, 4th qtr, vol. 13, no. 4, pp. 10915.
Driver, R.G. and G.Y. Grondin 2001, Steel plate shear walls, now performing on the
main stage, Modern Steel Construction, AISC, vol. 41, no. 10, pp. 4858.
Driver, R.G., G.L. Kulak, D.J.L. Kennedy, and A.E. Elwi 1998, Cyclic test of a four
storey steel plate shear wall, Journal of Structural Engineering, ASCE, vol. 124,
no. 2, pp. 11120.
Driver, R.G., G.Y. Grondin, and G.L. Kulak 2006, Unified block shear equation for
achieving consistent reliability, Journal of Constructional Steel Research, vol.
62, pp. 21022.
Driver, R.G., H.H. Abbas, and R. Sause 2006, Shear behavior of corrugated web bridge
girders, Journal of Structural Engineering, ASCE, vol. 132, no. 2, pp. 195203.
Drysdale, D. 1998, An Introduction to Fire Dynamics, 2nd edn, John Wiley, Chichester,
UK.
Duan, L. and W.F. Chen 1988, Effective length factor for columns in braced frames,
Duan, L. and W.F. Chen 1989, Design interaction equation for steel beamcolumns,
Duan, L. and W.F. Chen 1989, Effective length factor columns in unbraced frames,
Dubas, P. and E. Gehri (ed.) 1986, Behaviour and Design of Steel Plated Structures,
ECCS, Publication no. 44, ETH Hönggerberg, Zürich.
Dudley, W.C. and M. Lee 1988, Tsunami, 2nd edn, University of Hawaii Press, Honolulu.
Duggal, S.K. 2000, Design of Steel Structures, 2nd edn, Tata McGraw Hill, New Delhi,
p. 821.
Durgesh, C.R., Draft Code with Commentary on Seismic Evaluation and Strengthening
of Existing Buildings, www.nicee.org.
Easley, J.T. 1977, Strength and stiffness of corrugated metal shear diaphragms, Journal
Easterling, W.S. and L.G. Giroux 1993, Shear lag effects in steel tension members,
Engineering Journal, AISC, 3rd qtr, pp. 7784.
ECCS 1983, European Recommendations for the Fire Safety of Steel Structures:
Calculation of the Fire Resistance of Load Bearing Elements and Structural
Assemblies Exposed to Standard Fire, Elsevier, Brussels (see also ECCS 1995,
Fire Design Information Sheets, no. 82).
ECCS 1998, Surface Protection, 1st edn, Technical Committee 4, no. 90 & 98, Brussels.
EI Darwish, I.A. and B.G. Johnston 1965, Torsion of structural shapes, Journal of the
Structural Division, vol. 91, no. ST1, pp. 20327 (Errata 1966, vol. 92, no. ST1,
pp. 471).
Elgaaly, M. 1983, Web design under compressive edge loads, Engineering Journal,
AISC, vol. 20, no. 4, pp. 15371.
Elgaaly, M. 1997, Plate and box girders, in Handbook of Structural Engineering,
W.F. Chen (ed.), CRC Press, Boca Raton, FL, pp. 19.119.23.
Elgaaly, M. and A. Seshadri 1997, Girders with corrugated webs under partial
compressive edge loading, Journal of Structural Engineering, ASCE, vol. 123,
no. 6, pp. 78391.
Elgaaly, M. and H. Dagher 1997, Beams and Girders with Corrugated Webs,
Proceedings of the SSRC Annual Technical Session, Lehigh University, Bethlehem,
PA, pp. 3753.
Elgaaly, M., A. Seshadri, and R.W. Hamilton 1997, Bending strength of steel beams
with corrugated webs, Journal of Structural Engineering, ASCE, vol. 123, no. 6,
pp. 77282.
Elgaaly, M., R.W. Hamilton, and A. Seshadri 1996, Shear strength of beams with
corrugated webs, Journal of Structural Engineering, ASCE, vol. 122, no. 4, pp.
3908.
Ellifritt, D.S., G. Wine, T. Sputo, and S. Samuel, 1991, Flexural strength of WT sections,
Ellingwood, B. 1989, Serviceability guidelines for steel structures, Engineering
Ellingwood, B. and A. Tullin 1984, Structural serviceability: Floor vibration, Journal
of Structural Engineering, ASCE, vol. 110, no. ST2, pp. 40118 (see also Disc,
vol. 111, no. ST5, 1985, pp. 115861).
Ellingwood, B. and D. Rosowsky 1996, Combining snow and earthquake loads for
limit states design, Journal of Structural Engineering, vol. 122, no. 11, pp. 1364
8.
Engelhardt, M.D. and T.A. Sabol 1998, Reinforcing of steel moment connections with
cover plates: Benefits and limitations, Engineering Structures, vol. 20, no. 46, p.
510.
Engesser, F. 1889, Über die knickfestigkeit gerader stäbe, Zeitschrift des Architekten-
und Ingenieur-Vereins, Hannover, Germany, vol. 35, pp. 45562.
English, G.W. and P.F. Adams 1973, Experiments on laterally loaded steel beam
ENV 1993-1-1, Eurocode 3: Design of Steel StructuresPart 1.1: General Rules and
Rules for Buildings, European Committee For Standardization, Brussels, 1992.
ENV 1993-1-2, Eurocode 3: Design of Steel StructuresPart 1.2: General Rules
Structural Fire Design, European Committee for Standardization, Brussels, 1995.
ENV 1993-1-4, Eurocode 3: Design of Steel StructuresPart 1.4: General Rules and
Supplementary Rules for Stainless Steels, CEN, 1992.
Epstein, H.I. 1992, An experimental study of block shear failure of angles in tension,
AISC Engineering Journal, vol. 29, pp. 7584.
Epstein, H.I. and B.H. Thacker 1990, The Effect of Bolt Stagger for Block Shear
Tension Failures in Angles, Computers and Structures, vol. 39, no. 5, pp. 57176.
Epstein, H.I. and F.S. Gulia 1992, Finite Element Studies of Bolt Stagger Effects in
Tension Members, Computers and Structures, vol. 48, pp. 11536.
Epstein, H.I. and M.J. McGinnis 2000, Finite Element Modeling of Block Shear in
Structural Tees, Computers and Structures, vol. 77, pp. 57182.
Epstein, H.I. and R. Chamarajanagar 1994, Finite Element Studies for Bolt Shear Tests,
Computers and Structures, vol. 61, no. 5, pp. 96774.
References R.13
Epstein, H.I., E.M. Smith, and J.D. Mitchell 1998, Analysis and Assumptions of Cold
Formed Purlins, Practice Periodical on Structural Design and Construction,
ASCE, vol. 3, no. 2, pp. 607.
Errera, S.J. and T.V.S.R. Apparao 1976, Design of I-shaped beams with diaphragm
bracing, Journal of the Structural Div., ASCE, vol. 102, no. ST4 & ST9, pp. 769
81 & 16851701.
Euler, L. 1959, Sur le Force de Colonnes, Memoires de lAcademie Royale des Sciences
et Belles, Lettres, Berlin, vol. 13 (English translation by J.A. Van den Broek 1947,
American Journal of Physics, vol. 15, pp. 309).
Euro Inox 1994, Design Manual for Structural Stainless Steel, European Stainless Steel
Development Group, Nickel Development Institute, Toronto, Canada.
European Coal and Steel Community 1982, Durability of Steel Structures, Paris.
Evans, H.R. 1983, Longitudinally and Transversely Reinforced Plate Girders, in Plated
Structures, Stability and Strength, R. Narayanan (ed.), Elsevier Applied Science
Publishers, London, pp. 138.
Evans, H.R. and K.H. Tang 1986, Longitudinal stiffeners for girder webs: Their
behaviour and design, Journal of Constructional Steel Research, vol. 2, pp. 173
98.
Faella, C., V. Piluso, and G. Rizzano 2000, Structural Steel Semi-rigid Connections:
Theory, Design, and Software, CRC Press, Florida.
Fan, Y.L., Y.L. Mo, and R.S. Herman 2006, Hybrid Bridge Girders: A Preliminary
Design Example, Concrete International, ACI, vol. 28, no. 1, pp. 659.
Feld, J. and K. Carper 1997, Construction Failures, 2nd edn, Wiley, NY.
FEMA-15 1981, Design Guildelines for Flood Damage Reduction, Federal Emergency
Management Agency, www.fema.gov/hazards/floods/pubs/lib1.shtm, 11 April 2006,
p. 106.
FEMA-267/SAC-95-02 and FEMA 267A/SAC-96-03 1995 & 1997, Interim Guidelines:
Evaluation, Repair, Modification and Design of Welded Steel Moment Frame
Structures, Federal Emergency Management Agency, Sacrament, CA.
FEMA-353, Recommended Specifications and Quality Assurance Guidelines for Steel
Moment Frame Construction for Seismic Application, www.fema.gov/plan/prevent/
earthquake/pdf/fema-353.pdf, 1 June 2000.
FEMA-450 2003, NEHRP Recommended Provisions for New Buildings and Other
StructuresPart 1: Provisions, Part 2 Commentary, Building Seismic Safety
Council, National Institute of Building Sciences, Washington DC,
www.bssconline.org/NEHRP2003/provisions/, 6 June 2006.
FEMA-55 2000, Coastal Construction Manual, Federal Emergency Management
Agency, www.fema.gov/hazards/floods/lib55.shtm, 15 February 2005, p. 500.
Fisher, J.M. 1981, Structural details in industrial buildings, Engineering Journal, AISC,
vol. 18, 3rd qtr, pp. 8389 (see also Discussions 1982, 2nd qtr, pp.139-40).
Fisher, J.M. 1983, The importance of tension chord bracing, Engineering Journal,
AISC, vol. 20, 3rd qtr, 1983, pp.1036 (also see Discussions 1984, 2nd qtr, pp.122-
123).
Fisher, J.M. 1984, Industrial buildings: Guidelines and criteria, Engineering Journal,
AISC, vol. 21, 3rd qtr, pp. 14953.
Fisher, J.M. 1991, Industrial buildings, in Constructional Steel Design: An International

Guide, P.J. Dowling, J.E. Harding, and R. Bjorhovde (eds), Elsevier Applied
Science, London/NY, pp. 62744.
Fisher, J.M. and D.R. Buettner 1979, Light and Heavy Industrial Buildings, American
Institute of Steel Construction, Chicago, IL.
Fisher, J.W. 1978, Fatigue cracking in bridges from out-of-plane displacements,
Canadian Journal of Civil Engineering, vol. 5, no. 4.
Fisher, J.W. 1984, Fatigue and Fracture in Steel Bridges: Case Studies, Wiley
InterScience, NY.
Fisher, J.W. and D.R. Mertz 1985, Hundreds of Bridges-Thousands of Cracks, Civil
Fisher, J.W., G.L. Kulak, and Smith 1998, A Fatigue Primer for Structural Engineers,
National Steel Bridge Alliance, USA (see also www.nsbaweb.org).
Franssen, J.M., V.K.R. Kodur, and J. Mason 2000, User Manual For SAFIR, A Computer
Program for Analysis of Structures at Elevated Temperature Conditions, Report
Spec/2000-03, University of Liege, Belgium.
Fricke, W. 2003, Fatigue of Materials and Structures: Seminar Organized by Laboratory
for Mechanics of Materials, Technical University of Harburg, Germany (see also
http://www.Tu-Harburg.De/Skf/Fatiguecourse).
Frye, M.J. and G.A. Morris 1975, Analysis of flexibly connected steel frames, Canadian
Journal of Civil Engineering, vol. 2, no. 3, pp. 28091.
Fuchs, W., R. Eligehausen, and J.E. Breen 1995, Concrete capacity design (CCD)
approach for fastening to concrete, ACI Structural Journal, vol. 92, no. 1, pp. 73
94.
Fujii, T. 1971, A Comparison Between Theoretical Values and Experimental Results
for the Ultimate Shear Strength of Plate Girders, IABSE Colloquium on Design of
Plate and Box girders for Ultimate Strength, London.
Fukumoto, Y. and T.V. Galambos 1966, Inelastic lateral-torsional buckling of beam
Fukumoto, Y., D.A. Nethercot, and T.V. Galambos 1983, Experimental Data for the
Buckling of Steel Structures: NDSS Stability of Metal Structures, Proceedings,
Third International Colloquium, SSRC, Toronto, Canada, pp. 60930.
Fukumoto, Y., Y. Itoh, and M. Kubo 1980, Strength variation of laterally unsupported
beams, Journal of the Structural Div., ASCE, vol. 106, no. ST1, pp. 16582.
Galambos, T.V. (ed.) 1998, Guide to Stability Criteria for Metal Structures, 5th edn,
John Wiley, NY, p. 911.
Galambos, T.V. 1968, Structural Members and Frames, Prentice-Hall, NY.
Galambos, T.V. 1981, Load and resistance factor design, Engineering Journal, AISC,
3rd qtr, vol. 18, no. 3, pp. 7482.
Galambos, T.V. and B. Ellingwood 1986, Serviceability limit states: Deflection, Journal
of Structural Engineering, ASCE, vol. 112, no. 1 & 3, pp. 6784.
Galambos, T.V. and M.K. Ravindra 1978, Properties of steel for use in load and
resistance factor design, Journal of Structural Div., ASCE, vol. 104, no. ST9.
Galambos, T.V. and R.L. Ketter 1961, Columns under Combined Bending and Thrust,
Transactions, ASCE, vol. 126, Part I, pp. 125.
References R.15
Galambos, T.V., F.J. Lin, and B.G. Johnston 1996, Basic Steel Design with LRFD,
Prentice-Hall, NJ.
Galambos, T.V., Hajjar, J.F., Earls, C.J. and Gross, J.L., Required properties of High-
Performance Steel, www.fire.nist.gov/bfrlpubs/, May 1997, p. 98.
Galvery Jr, W.L. and F.M. Marlow 2001, Welding Essentials: Questions and Answers,
Expanded edn, Industrial Press, NY, p. 480.
Ganapathy Chettiar, C. 1975, Permissible Stresses in Axial Compression in IS: 800-
1962', ISI Bulletin, vol. 27, no. 7, pp. 2415.
Ganapathy, C. 1972, An Investigation on the Strength and Behaviour of Latticed Steel
Structures', Ph D thesis, IIT, Madras.
Ganapathy, C., and N. Subramanian 1977, A Computer Program for the Buckling
Analysis of Space Frames, Computer Society of India, Annual Convention, Pune,
India.
Garas F., K.S. Virdi, R. Mathews, and J.L. Clarke 2000, Abnormal Loading on Structures,
Spon Press, London, p. 384.
Gardner, L. and D.A. Nethercot 2004, Structural Stainless Steel Design: A New
Approach, The Structural Engineer, vol. 82, no. 21, pp. 218.
Gardner, L. and D.A. Nethercot 2005, Designers Guide to EN 1993-1-1Eurocode 3:
Design of Steel Structures: General Rules and Rules for Buildings, Thomas Telford,
Steel Construction Institute, London.
Gaylord, E.H., C.N. Gaylord, and J.E. Stallmeyer 1992, Design of Steel Structures, 3rd
edn, McGraw Hill International, NY, p. 792, pp. 11582, pp. 36772, & pp. 410
54.
Gaylord, E.H., C.N. Gaylord, and J.E. Stallmeyer 1996, Structural Engineering
Handbook, 4th edn, McGraw Hill, NY, p. 1248.
Gere, J.M. and W. Weaver 1969, Analysis of Framed Structures, Van Nostrand, NY.
Gerstle, K.H. and M.H. Ackroyd 1990, Behaviour and design of flexibility-connected
building frames, Engineering Journal, AISC, vol. 27, no. 1, pp. 229.
Ghosh, A. 2004, Modern approach of design of welded components subjected to fatigue
loading, Journal of Structural Engineering, ASCE, vol. 130, no. 5, pp. 81220.
Ghosn, A.A. and R.R. Sinno 1996, Load capacity of nested, laterally braced, cold-
formed steel Z-section beams, Journal of Structural Engineering, ASCE, vol.
122, no. 8, pp. 96871 (see also vol. 128, no. 11, 2002, pp. 14238).
Giddings, T.W. 1978, Fire Resistant Construction in SHSToday and Tomorrow,
Building Specifications, pp. 6572.
Gilvery, K.R. and R.J. Dexter 1997, Evaluation of Alternative Methods of Fire Rating
Structural Elements, National Institute of Standards and Technology, NIST-GCR-
97-718, Gaithersburg, USA.
Gioncu, V. and F.M. Mazzolani 2002, Ductility of Seismic Resistant Steel Structures,
Span Press, London and NY, p. 687.
Goda, Y. 2000, Random Seas and Design of Maritime Structures, World Scientific
Publishing Co., Singapore, p. 443.
Gordon, J.E. 1978, Structures (or Why Things Dont Fall Down), Penguin Books, NY.
Goto, Y. and W.F. Chen 1987, Second-order elastic analysis for frame design, Journal
of Structural Div., ASCE, vol. 113, no. 7, pp. 150119.
Gourd, L.M. 1980, Principles of Welding Technology, Edward Arnold, London.
Goyet, V.V., Fr. Frey, and Ch. Massonnet 1981, Ultimate Load of Trusses Buckling in
their Plane', IABSE Proceedings, P-47/81, November, pp. 14164.
Graham, J.D., A.N. Sherbourne, R.N. Khabbaz, and C.D. Jensen 1959, Welded Interior
Beam-to-Column Connections, American Institute of Steel Constructions, NY.
Greiner, R. and J. Lindner 2006, Interaction formulae for members subjected to bending
and axial compression in Eurocode 3: The method 2 approach, Journal of
Constructional Steel Research, vol. 62, no. 8, pp. 757-70.
Gross, J.M., J.G. Orbison, and R.D. Ziemian 1995, Block shear tests in high-strength
steel angles, AISC Engineering Journal, 3rd qtr, pp. 11722.
Grundy, P., I.R. Thomas, and I.D. Bennetts 1980, Beam-to-column moment
connections, Journal of the Structural Div., ASCE, vol. 106, no. ST1, pp. 31330
(see also Disc. by N. Krishnamurthy 1980, pp. 2573-2574).
Gupta, A.K. 1984, Buckling of coped steel beams, Journal of the Structural
Engineering, ASCE, vol. 110, no. 9, pp. 197787 (see also Disc. by J.J. Cheng and
Y.A. Yura 1986, vol. 112, no. 1, pp. 20104).
Gupta, T.N. (ed.) 1998, Building Materials in India: 50 yearsA Commemorative
Volume, Building Materials and Technology Promotion Council, New Delhi, p.
560.
Gurney, T.R. 1976, Fatigue Design Rules for Welded Steel Joints, The Welding Institute,
Cambridge, UK.
Gurney, T.R. 1979, Fatigue of Welded Structures, 2nd edn, Cambridge University Press,
England.
Haaijer, G. and B. Thürlimann 1960, On Inelastic Buckling in Steel, Transactions of
ASCE, vol. 125, pp. 30844.
Habenicht, G. 1997, Kleben-Grundlagen, Technologie, Anwendungen, 3rd edn, Springer-
Verlag, Berlin.
Hancock, G.J., J.P. Papangelis, and M.J. Clarke 1995, Plane Rigid Frame Structural
Analysis (PRFSA) User Manual, Centre for Advanced Structural Engineering,
University of Sydney, Australia (www.civil.usyd.edu.au/case/prfsa.php).
Handbook in Structural Steel Detailing, Institute of Steel Development and Growth,
Kolkata, Publication no. INS / PUB 018, 1998.
Harrison, H.B. 1990, Structural Analysis and DesignParts 1 and 2, 2nd edn, Pergamon
Press, Oxford.
Hartshorn (ed.) 1986, Structural Adhesives: Chemistry and Technology, Plenum Publ.
Corp, NY.
Hasan, R., N. Kishi, W.F. Chen, and M. Komuro 1997, Evaluation of extended end-
plate connections, Journal of Structural Engineering, ASCE, vol. 123, no. 12, pp.
15951602.
Haseltine, B.A. 1975, Comparison of energy requirements for buildings materials and
structures, The Structural Engineer, vol. 153, no. 9, pp. 35765.
Hatfield, F.J. 1992, Design chart for vibration of office and residential floors,
Engineering Journal, AISC, vol. 29, no. 4, 4th qtr, pp. 1414.
He, W. 1996, Stepped-Section Steel Angle, in Advances in Steel Structures, ICASS
96, Hong Kong, Proceedings Published by Penguin Press.
Helwig, T.A and K.H. Frank 1999, Stiffness requirements for diaphragm bracing of
beams, Journal of the Structural Engineering, vol. 125, No. 11, pp. 1249 56.
References R.17
Herzog, M. 1974, Ultimate strength of plate girders from tests, Journal of the Structural
Herzog, M.A.M. 1991, Unified design approach to steel beamcolumns, Journal of
Constructional Steel Research, vol. 20, no. 4, pp. 291303.
Hicks, J. 2000, Welded Joint Design, 3rd edn, Industrial Press, NY, p. 141.
Hill, H.N. 1954, Lateral buckling of channels and Z-beams, Transactions, ASCE, vol.
119, pp. 82941.
Höglund, T. 1973, Design of thin plate I-girders in shear and bending with special
reference to web buckling, Bulletin No. 94, Div. Building Statics and Structural
Engineering, Royal Inst. of Tech., Stockholm, p. 43.
Hollow Structural Section Connections Manual, AISC, Chicago, 1997.
Holmes, J.D. 2001, Wind Loading of Structures, Spon Press, London and NY, p. 356.
Holmes, M. and L.H. Martin 1983, Analysis and Design of Structural Connections,
Ellies Horwood Ltd., Chichester, West Sussex, England.
Horne, M.R. 1951, The Plastic Theory of Bending of Mild Steel Beams with Particular
Reference to the Effect of Shear Forces, Proc. Royal Society, vol. 207 (A), no.
216.
Horne, M.R. 1964, Safe Loads on I-section Columns in Structures Designed by Plastic
Theory, Paper no. 6794, Proc. of the Institution of Civil Engineers, vol. 29, pp.
13750.
Horne, M.R. 1975, An Approximate Method for Calculating the Elastic Critical Loads
of Multi-storey plane frames, The Structural Engineer, vol. 15, no. 6, pp. 2428.
Horne, M.R. 1979, Plastic Theory of Structures, Pergamon Press Ltd., Oxford.
Horne, M.R. and L.J. Morris 1981, Plastic Design of Low-rise Frames, Granada, London.
Hoshino, K. 2001, Market Development for Stainless Steel, Steel Today and Tomorrow,
no. 155, pp. 58.
Hotchkiss, J.G. 1966, Torsion of rolled steel sections in building structures, Engineering
http://www.civil.canterbury.ac.nz/fire/fe_resrch_reps.html, December 2005.
http://www.firepro.co.nz/datasheets/, November 2006.
http://www.structural-engineering.fsnet.co.uk/ (lists a number of free structural software
packages).
IRC 6-2000, Standard Specifications and Code of Practice for Road Bridges: Section
II, Loads and Stresses, The Indian Roads Congress, New Delhi, 2000.
IS: 1024-1999, Code of Practice for Use of Welding in Bridges and Structures Subjected
to Dynamic Loading, 2nd rev., Bureau of Indian Standards, New Delhi.
IS: 1149-1982, High Tensile Steel Rivet Bars for Structural Purposes, 3rd rev., Bureau
of Indian Standards, New Delhi.
IS: 11587-1986, Specification for Structural Weather Resistant Steel, Bureau of Indian
Standards, New Delhi.
IS: 1161-1998, Specification for Steel Tube for Structural Purposes, 4th edn, Bureau of
Indian Standards, New Delhi.
IS: 1261-1959, Code of Practice for Seam Welding in Mild Steel, Bureau of Indian
IS: 1278-1972, Specification for Filler Rods and Wires for Gas Welding, 2nd rev., Bureau
IS: 1323-1982, Code of Practice for Oxy-acetylene Welding for Structural Work in
Mild Steels, 2nd rev., Bureau of Indian Standards, New Delhi.
IS: 1363-2002, Part 1-3, Hexagon Head Bolts, Screws and Nuts of Product grade C,
4th rev., Bureau of Indian Standards, New Delhi.
IS: 1364-2002, Part 1-5, Hexagon Head Bolts, Screws and Nuts of Product Grades A
and B, 4th rev., Bureau of Indian Standards, New Delhi.
IS: 1367-1992 (Parts 118), Technical Supply Conditions for Threaded Steel Fasteners,
Bureau of Indian Standards, New Delhi.
IS: 1395-1982, Low and Medium Alloy Steel Covered Electrodes for Manual Metal Arc
Welding, 3rd rev., Bureau of Indian Standards, New Delhi.
IS: 1477-2000, Code of Practice for Painting of Ferrous Metals in BuildingsPart 1:
Pre-treatment, Part 2: Painting, 2nd rev., Bureau of Indian Standards, New Delhi.
IS: 158147-1976, Code of Practice for Use of Aluminium Alloys in Structures, Bureau
IS: 1641-1988, Code of Practice for Fire Safety of Buildings (General): General
Principles of Fire Grading and Classification, 1st rev., Bureau of Indian Standards,
New Delhi.
IS: 1642-1989, Code of Practice for Fire Safety of Buildings (General): Details of
Construction, 1st rev., Bureau of Indian Standards, New Delhi.
IS: 1643-1988, Code of Practice for Fire Safety of Buildings (General): Exposure
Hazard, 1st rev., Bureau of Indian Standards, New Delhi.
IS: 1644-1988, Code of Practice for Fire Safety of Buildings (General): Exit
Requirements and Personal Hazard, 1st rev., Bureau of Indian Standards, New
Delhi.
IS: 1852-1985, Rolling and Cutting Tolerances for Hot Rolled Steel Products, 4th rev.,
IS: 1893-2002, Criteria for Earthquake Resistant Design of StructuresPart 1: General
Provisions and Buildings, 5th rev., Bureau of Indian Standards, New Delhi.
IS: 1929-1982, Specification for Hot Forged Steel Rivets for Hot Closing (1236 mm
diameter), 1st rev., Bureau of Indian Standards, New Delhi.
IS: 2062-2006, Hot rolled low, medium and high tensile structural steel, 6th rev., Bureau
IS: 2155-1982, Specification for Cold Forged Solid Steel Rivets for Hot Closing (616
mm diameter), 1st rev., Bureau of Indian Standards, New Delhi.
IS: 3640-1982, Specification for Hexagon Fit Bolts, 1st rev., Bureau of Indian Standards,
New Delhi.
IS: 3757-1985, Specification for High Strength Structural Bolts, 2nd rev., Bureau of
Indian Standards, New Delhi.
IS: 4000-1992, Code of Practice for High Strength Bolts in Steel Structures, 1st rev.,
IS: 4759-1996, Hot-dip Zinc Coatings on Structural Steel and other Allied Products,
3rd rev., Bureau of Indian Standards, New Delhi.
IS: 4991-1968, Criteria for Blast Resistant Design of Structures for Explosions Above
Ground, Bureau of Indian Standards, New Delhi.
IS: 4923-1997, Standard Specification for Hollow Steel Sections for Structural Use,
2nd edn, Bureau of Indian Standards, New Delhi.
References R.19
IS: 5369-1975, General Requirements for Plain Washers and Lock Washers, 1st rev.,
IS: 5370-1969, Specification for Plain Washers with Outside Diameter-3 ´ Inside
Diameter, Bureau of Indian Standards, New Delhi.
IS: 5372-1975, Taper Washer for Channels (ISMC), 1st rev., Bureau of Indian Standards,
New Delhi.
IS: 5374-1975, Taper Washers for I-beams (ISMB), 1st rev., Bureau of Indian Standards,
New Delhi.
IS: 6419-1996, Welding Rods and Bare Electrodes for Gas Shielded Arc Welding of
Structural Steel, 1st rev, Bureau of Indian Standards, New Delhi.
IS: 6533-1989, Code of Practice for Design and Construction of Steel ChimneysPart
1: Mechanical Aspects; Part 2: Structural Aspects, 1st rev., Bureau of Indian
IS: 6603-2001, Specification for Stainless Steel Bars and Flats, Bureau of Indian
Standards, 1st rev., New Delhi, 1972.
IS: 6610-1972, Specifications for Heavy Washers for Steel Structures, Bureau of Indian
IS: 6623-2004, Specifications for High Strength Structural Nuts, 1st rev., Bureau of
Indian Standards, 1st rev., New Delhi.
IS: 6639-2005, Specifications for hexagonal bolts for steel structures, Bureau of Indian
Standards, 1st rev., New Delhi.
IS: 6649-1985, Specification for Hardened and Tempered Washers for High Strength
Structural Bolts and Nuts, 1st rev, Bureau of Indian Standards, New Delhi.
IS: 7280-1974, Specifications for Bare Wire Electrodes for Submerged Arc Welding of
Structural Steels, Bureau of Indian Standards, New Delhi.
IS: 800-2007, Indian Standard Code for General Construction in Steel, 3rd rev., Indian
Standards Institution, New Delhi, 2007.
IS: 801-1975, Code of Practice for Cold-formed Light Gauge Steel Structural Members
in General Building Construction, 1st rev., Bureau of Indian Standards, New Delhi.
IS: 802 (Part 1, Sec. 1)-1995, Use of Structural Steel in Overhead Transmission Line
Towers-Code of PracticePart 1: Material, Loads and Permissible Stresses, Sec.
1: Materials and Loads and Sec. 2: Permissible Stresses, (1992), 3rd rev., Bureau
IS: 806-1968, Code of Practice for Use of Steel Tubes in General Building Construction,
1st rev., Bureau of Indian Standards, New Delhi.
IS: 807-2006, Code of Practice for Design, Erection and Testing (Structural portion)
of Cranes and Hoists, Bureau of Indian Standards, New Delhi.
IS: 814-2004, Covered Electrodes for Manual Metal Arc Welding of Carbon and Carbon
Manganese Steel, 6th rev., Bureau of Indian Standards, New Delhi.
IS: 816-1969, Code of Practice for Use of Metal Arc Welding for General Construction
in Mild Steel, 1st rev., Bureau of Indian Standards, New Delhi.
IS: 819-1957, Code of Practice for Resistance Spot Welding for Light Assemblies in
Mild Steel, Bureau of Indian Standards, New Delhi.
IS: 8500-1991, Structural SteelMicro Alloyed (medium and high strength qualities):
Specifications, 1st rev., Bureau of Indian Standards, New Delhi.
IS: 875-1987, Code of Practice for Design Loads (other than earthquake) for Buildings
and Structures (Parts 15), 2nd rev., Bureau of Indian Standards, New Delhi.
IS: 9172-1979, Recommended Design Practice for Corrosion Protection of Steel
Structures, Bureau of Indian Standards, New Delhi.
IS: 9178-1979, Criteria for Design of Steel Bins for Storage of Bulk MaterialsPart 1:
General Requirements and Assessment of Loads; Part 2: Design Storage Criteria,
Iwankiw, N.R. 1987, Design for eccentric and inclined loads on bolt and weld groups,
AISC Engineering Journal, vol. 24, 4th qtr.
Iwankiw, N.R. 1997, Ultimate strength considerations for seismic design of the reduced
beam section (internal plastic hinge), Engineering Journal, AISC, vol. 34, no. 1,
pp. 316.
Iwankiw, N.R. and C.J. Carter 1996, The Dogbone: A New Idea to Chew On, Modern
Steel Construction, AISC, vol. 36, no. 4, pp. 1823.
Jain, S.K. 1995, A proposed draft of IS: 1893 provisions on seismic design of
buildingsPart II: Commentary and examples, Journal of Structural Engineering,
SERC, vol. 22, no. 2, pp. 7390.
Jain, S.K. 2004, Explanatory Examples on Indian Seismic Code IS: 1893 (Part 1),
www.nicee.org/IITK-GSDMA/EQ21.pdf, 30 December 2004.
Jain, S.K. and C.V.R. Murty 2004, Proposed Draft Provisions and Commentary on
Indian Code IS: 1893 (Part 1), www.nicee.org/IITK-GSDMA/EQ05.pdf, 30
December 2004.
Jamshidi, M., S. Fallaha, A. Azizinamini, K. Price, and M. Cress 1997, Application of
High Performance Steel in Steel Bridge Construction Proceeedings of Building to
Last Structures Congress, vol. 1, ASCE, NY.
Jeffus, L. 2002, Welding: Principles and Applications, 5th edn, Thomson Delmar
Learning, p. 944.
Jiang, X.M., H. Chen, and J.Y.R. Liew 2002, Spread of plasticity analysis of three
dimensional steel frames, Journal of Constructional Steel Research, vol. 58, pp.
193212.
Johnson, B.G. (ed.) 1960, Guide to Design Criteria for Metal Compression Members,
Column Research Council and John Wiley & Sons, NY.
Johnson, R.P. 1994, Composite Structures in Steel and Concrete: Beams, Columns,
Frames and Applications in Buildings, vol. 1, Blackwell Scientific Publications,
London, 1994.
Johnston, B.G. (ed.) 1976, Guide to Stability Design Criteria for Metal Structures, 3rd
edn, John Wiley, NY.
Johnston, B.G. 1982, Design of W-shapes for combined bending and torsion,
Joint Committee of Welding Research Council and the American Society of Civil
Engineers 1971, Commentary on Plastic Design in Steel, 2nd edn, ASCE Manual
and Reports on Practice, no. 41, NY.
Jones, D.R.H. 1998, Failure Analysis: Case Studies, Elsevier Science, p. 444.
Jones, S.W., P.A. Kirby, and D.A. Nethercot 1981 Modeling of Semi-rigid Connection
Behaviour and its Influence on Steel Column Behaviour, Joints in Structural Steel
Work, J.H. Howlett, W.M. Jenkins, and R. Stainby (eds), Pentech Press, pp. 5.73
5.78.
References R.21
Journal of Structural Engineering, ASCE, vol. 128, no. 4, 2002, Special issue on Steel
Moment Frames after Northridge, pp. 413555.
Julicher, A.J. 1981, Welding fundamentals for structural engineers, Civil Engineering,
ASCE, vol. 51, no. 1, pp. 60-61.
Kalyanaraman, V., T. Pekoz, and G. Winter 1977, Unstiffened compression elements,
Journal of the Structural Div., ASCE, vol. 103, no. ST9, pp. 183348.
Kaminetzky, D. 1991, Design and Construction Failures: Lessons from Forensic
Investigations, McGraw Hill, NY.
Kanchanalai, T. 1977, The Design and Behaviour of Beam-columns in Unbraced Steel
Frames, AISI Project no. 189, Report no. 2, Civil Engineering/Structures Research
Lab., University of Texas, Austin, p. 300.
Kato, B., W.F. Chen, and M. Nakao 1988, Effects of joint-panel shear deformation on
frames, Journal of Constructional Steel Research, vol. 10, pp. 269320.
Kavanagh, T. 1975, Some aesthetic considerations in steel design, Journal of the
Structural Division, ASCE, vol. 101, no. 11, pp. 225775.
Kavanagh, T.C. 1962, Effective length of framed columns, Transactions, ASCE, vol.
127, Part II, pp. 81101.
Keating, P.B. 1994, Focussing on fatigue, Civil Engineering, ASCE, vol. 64, no. 11,
pp. 547.
Kennedy, D.J.L., A. Picard, and D. Beaulieu 1990, New Canadian provisions for the
design of steel beam-columns, Canadian Journal of Civil Engineering, vol. 17,
pp. 87393.
Kennedy, D.J.L., A. Picard, and D. Beaulieu 1993, Limit states design of beam-columns:
The Canadian approach and some comparisons, Journal of Constructional Steel
Research, vol. 25, no. 1-2, pp. 14164.
Kerdal, D. and D.A. Nethercot 1984, Failure modes of castellated beams, Journal of
Constructional Steel Research, vol. 4, pp. 295315.
Kerensky, O.A., A.R. Flint, and W.C. Brown 1956, The Basis for Design of Beams and
Plate Girders in the Revised British Standard 153, Proceedings of the Institution
of Civil Engineers (London), vol. 5, no. Part III, pp. 396461.
Ketter, R.L. 1961, Further studies of the strength of beamcolumns, Journal of the
Kevin, L.R., M. Clark, and A.W. Knott 2000, Failure analysis case information
disseminator, Journal of Performance of Constructed Facilities, ASCE, vol. 16,
no. 3, pp. 12731.
Khalil, S.H. and C.H. Ho 1979, Black bolts under combined tension and shear, The
Structural Engineer, vol. 57B, pp. 6976.
Khanna, A.S. 1999, Corrosion resistant steel: Is it moneys worth?, Construction World,
vol. 2, no. 2, pp. 368.
Kim, Y. and W.F. Chen 1998, Practical analysis for partially restrained frame design,
Kindmann, R. and R. Muszkiewicz 2004, Biegedrillknickmomente und eigenformen
von biegeträgern unter berücksichtigung der drehbettung, Stahlbau, vol. 73, no. 2,
pp. 98106.
King, C.M. 2005, Design of Steel Portal frames for Europe, Steel Construction Institute,
Ascot, London.
Kirby, B.R. 1986, Recent developments in structural fire engineering design, Fire
Safety Journal, vol. 11, pp. 14179.
Kirby, B.R., and R.R. Preston 1988, High temperature properties of hot-rolled structural
steels for use in fire engineering design studies, Fire Safety Journal, vol. 13, pp.
2737.
Kirby, P.A. and D.A. Nethercot 1979, Design for Structural Stability, Granada Publishing,
London.
Kishi, N., and W.F. Chen 1990, Moment-rotation relation of semi-rigid connections
with angles, Journal of Structural Engineering, ASCE, vol. 116, no. 7, pp. 1813
34.
Kishi, N., R. Hasan, W.F. Chen, and Y. Goto 1997, Study of Eurocode 3 Steel Connection
Classification, Engineering Structures, vol. 19, no. 9, pp. 7729.
Kishi, N., W.F. Chen, and Y. Goto 1997, Effective length factor of columns in semi-
rigid and unbraced frames, Journal of Structural Engineering, ASCE, vol. 123,
no. 3, pp. 31320.
Kishi, N., W.F. Chen, Y. Goto, and K.G. Matsuoka 1994, Analysis Program for the
Design of Flexibly Jointed Frames, Computers and Structures, vol. 49, no. 4, pp.
70513.
Kishi, N., W.F. Chen, Y. Goto, and K.G. Matsuoka 1995, Design aid of semi-rigid
frame design, Engineering Journal, AISC, vol. 32, no. 3, pp. 90107.
Kitipornchai, S. and H.W. Lee 1986, Inelastic buckling of single angle, tee and double
angle struts, Journal of Constructional Steel Research, London, vol. 6, no. 1, pp.
320 (see also vol. 6, no. 3, pp. 21936).
Kitipornchai, S. and N.S. Trahair 1980, Buckling properties of mono-symmetric I-
Kitipornchai, S., C.M. Wang, and N.S. Trahair 1986, Buckling of mono-symmetric I-
beams under moment gradient, Journal of the Structural Div., ASCE, vol. 112,
no. 4, pp. 78199.
Kitipornchai, S., P.F. Dux, and N.J. Richter 1984, Buckling and bracing of cantilevers,
Kloiber, L. 2001, Connections for Hollow Structural Sections, Structure, SEI/ASCE,
pp. 4043.
Klöppel, K. and E. Winkelmann 1962, Experimentalle und theoretische untersuchungen
über die traglast von zweiachsig aüßermittig gedrückten Stahlstäben, Stahlbau,
vol. 31, pp. 3347, 7887, & 10919.
Knowles, P.1987, Design of Structural Steelwork, 2nd edn, Surrey University Press,
Guildford, UK.
Knowles, P.R. 1985, Design of Castellated Beams, Steel Construction Institute, Ascot,
UK.
Komatsu, S. 1971, Ultimate Strength of Stiffened Plate Girders subjected to Shear,
IABSE Colloquium, Design of Plate and Box Girders for Ultimate Strength, London.
Kosteski, N. and J.A. Packer 2003, Longitudinal plate and through plate-to-hollow
structural section welded connections, Journal of Structural Engineering, ASCE,
vol. 129, no. 4, pp. 47886.
Krawinkler, H. 1978, Shear in beam-column joints in seismic design of steel frames,
References R.23
Krawinkler, H. and S. Mohasseb 1987, Effect of panel zone deformation on seismic

response, in Special Issue on Joint Flexibility in Steel Frames, W.F. Chen (ed.),
Journal of Constructional Steel Research, vol. 8, pp. 23350.
Krishna, P. and R. Gupta 1992, Studies on structures using wind tunnel, The Indian
Concrete Journal, vol. 66, no. 11.
Krishna, P., K. Kumar, N.M. Bhandari, and A.K. Ahuja 1987, Review of Indian Wind
Code, IS: 875 (Part 3)-1987, www.nicee.org/IITK-GSDMA/W01.pdf.
Krishnamurthy, N. 1978, A fresh look at bolted end-plate behaviour and design,
Engineering Journal, AISC, vol. 15, no. 2, 2nd qtr, pp. 3949 (see also Discussions,
1979, vol. 16, no. 2, pp. 5464).
Krishnamurthy, N., H.T. Huang, P.K. Jefferey, and L.K. Avery 1979, Analytical M-G
curves for end-plate connections, Journal of Structural Div., ASCE, vol. 105, no.
ST1, pp. 13345.
Kuhn, G. and H.R. Lundgren 1977, An Appraisal of the Effective Length Alignment
Charts, International Colloquium on Stability of Structures under Static and
Dynamic Loads, Washington DC, ASCE, pp. 21242.
Kulak, G.L. and E.Y. Wu 1997, Shear lag in bolted angle tension members, ASCE,
Kulak, G.L. and G.Y. Grondin 2000, Block Shear Failure in Steel Members: A Review
of Design Practice, Fourth International Workshop on Connections in Steel
Structures, October 2225, Roanoke, VA, pp. 32939.
Kulak, G.L. and G.Y. Grondin 2002, Limit States Design in Structural Steel, 7th edn,
Canadian Institute of Steel Construction, Toronto, Ontario.
Kulak, G.L., J.W. Fisher, and J.H.A. Struik 1987, Guide to Design Criteria for Bolted
and Riveted Joints, 2nd edn, John Wiley, NY, p. 309.
Kulak, G.L., L. Kennedy, R.G. Driver, and M. Medhekar 2001, Steel plate shear walls:
An overview, Engineering Journal, AISC, vol. 39, no. 1, pp. 5062.
Kulicki, J.M. 2000, The Shape of Things to Come, Civil Engineering, ASCE, vol. 70,
no. 2, pp. 40-41.
Kumar, K., N.M. Bhandari, and P. Krishna 2004, Wind Loads on Buildings and
Structures: Proposed Draft and Commentary, IS: 875 (Part 3), www.nicee.org/
IITK-GSDMA/W02. pdf, p. 104.
Kumar, P. 2005, Structural Fire Safety, New Building Materials and Construction
World, vol. 11, no. 2, pp. 90102.
Kumar, S. 2002, Live loads in residential buildingsPart I: The results of the survey,
Indian Concrete Journal, vol. 76, no. 3, pp 157-163.
Kumar, S. 2002, Live loads in residential buildingsPart II: Life time maximum loads,
Indian Concrete Journal, vol. 76, no. 4, pp. 244-250
Kumar, S. and C.V.S. Kameswara Rao 1994, Live loads in residential buildings in
urban and rural areas, The Indian Concrete Journal, vol. 68, no. 10, pp. 541-548.
Kumar, S. and C.V.S.K. Rao 1997, Fire loads in office buildings, Journal of Structural
LaBoube, R.A. 1992, Estimating uplift capacity of light steel roof system, Journal of
Structural Engineering, ASCE, vol. 118, no. 3, pp. 84852.
Lamont, S., B. Lane, A. Usmani, and D. Drysdale 2003, Assessment of the fire resistance
test with respect to beams in real structures, Engineering Journal, AISC, vol. 40,
no. 2, pp. 6375.
Lathan, D.J., B.R. Kirby, and G. Thomson 1987, The temperatures attained by
unprotected steelwork in experimental natural fires, Fire Safety Journal, vol. 12,
pp. 13952.
Law, M. 1983, 'A Basis for the Design of Fire Protection for Building Structures, The
Structural Engineer, vol. 61a, no. 1, pp. 2533.
Lawson, R.M. 1985, Fire Resistance of Ribbed Concrete Floors, Report 107,
Construction Industry Research and Information Association, UK.
Lawson, R.M. 1989, Design of Composite Beams and Slabs with Steel Decking, The
Steel Construction Institute, p. 55.
Lawson, R.M. and G.M. Newman 1990, Fire Resistant Design of Steel StructuresA
Handbook To BS 5950: Part 8, The Steel Construction Institute, Publication no.
80.
Lawson, R.M. et al. 1999, Slim-floor and slimdeck construction: European
developments, The Structural Engineer, vol. 77, no. 8, pp. 2250.
Lay, M.G. and T.V. Galambos 1966, Bracing requirements for inelastic steel beams,
Lee, S.C., C.H. Yoo, and D.Y. Yoon 2003, New design rules for intermediate transverse
stiffeners attached on web panels, Journal of Structural Engineering, ASCE, vol.
129, no. 12, pp. 160714 (Errata, 2004, vol. 130, pp. 693).
LeMessurier, W.J. 1972, A practical method of second order analysisPart 2: Rigid
frames, Engineering Journal, AISC, vol. 14, no. 2, 2nd qtr, pp. 4967.
Lescouarch, Y. and A. Colson 1992, Column Bases, in Constructional Steel Design:
An International Guide, P.J. Dowling, J.F. Harding, and R. Bjorhovde (eds), Elsevier
Applied Science, London, pp. 37996.
Lesik, D.F. and D.J.L. Kennedy 1990, Ultimate strength of fillet welded connections
loaded in plane, Canadian Journal of Civil Engineering, vol. 17, pp. 5567.
Levy, M. and M. Selvadori 1992, Why Buildings Fall Down: How Structures Fail,
W.W. Norton, NY.
Lewis, K.R. 2000, Fire Design of Steel Members, Fire Engineering Research Report
2000/07, University of Canterbury, Christchurch, NZ.
Li, J.J. and G.Q. Li 2002, Large scale testing of steel portal frames comprising tapered
beams and columns, Advances in Structural Engineering, vol. 5, no. 4, pp. 259
69.
Liew, J.Y.R., D.W. White, and W.F. Chen 1991, Beam-column design in steel
frameworks: Insights on current methods and trends, Journal of Constructional
Steel Research, vol. 18, no. 4, pp. 259308.
Liew, J.Y.R., D.W. White, and W.F. Chen 1994, Notional load plastic hinge method for
frame design, Journal of Structural Engineering, ASCE, vol. 120, no. 5, pp. 1434
54.
Liew, T.Y.R., D.W. White, and W.F. Chen 1993, Second-order refined plastic hinge
analysis for frame design, Parts I and II, Journal of Structural Engineering, ASCE,
vol. 119, no. 11, pp. 31963216 & 321737.
Lindner, J. 1972, Mindeststeifigkeiten für den kippsicherheitsnachweis beim
traglastverfahren, Der Bauingenieur, vol. 47, H. 7, pp. 23840.
Lindner, J. 1978, Näherungen fur die Europäischen Knickspannungskurven, Die
Bautechnik, vol. 55, no. 10, pp. 3447.
References R.25
Lindner, J. 1980, Biegedrillknicken in Theorie, Versuch und Praxis, Berischte am

Forschung und Entwicklun, Deutscher Ausschuss für Stahlbau (DASt), Stahlbau
Verlag, Köln, pp. 719.
Lindner, J. 1988, Grenzschubtragfähigheit von I trägern mit trapaezförmig profilierten
stegen, Der Stahlbau, vol. 57, no. 12, pp. 37780.
Lindner, J. 1995, Influence of constructional detailing on the lateral torsional buckling
capacity of beam columns, in Structural Stability and Design, A.A. Balkema,
Rotterdam, pp. 616.
Lindner, J. 1997, Design of steel beams and beam columns, Engineering Structures,
vol. 19, no. 5, pp. 37884.
Lindner, J. 2003, Design of beams and beam columns, Progress in Structural
Engineering and Materials, vol. 5, no. 1, pp. 3847.
Lindner, J. and B. Huang 1995, Beulwerte für trapezförmig profilierte Bleche under
Schubbeanspruchung, Der Stahlbau, vol. 61, no. 12, pp. 3704.
Lindner, J. and N. Subramanian 1982, Allowable stress provisions of IS: 800-1962,
Journal of the Institution of Engineers (India), vol. 62, pt CI4, pp. 2468.
Lindner, J. and R. Gietzelt 1980, Biegedrillknicken Erläuterungen, Versuche,
Beispiele, DASt, 10/1980, Stahlbau Verlag, Köln.
Lindner, J. and R. Gietzelt 1985, Zweiachsige Biegung and Längskraft-ein ergänzter
Bemessungsvorschlag, Stahlbau, vol. 54, pp. 26571.
Lindner, J. and T. Glitsch 2004, Vereinfachter Nachweis für I und U Träger-
beansprucht durch dopplete biegung und torsion, Stahlbau, vol. 73, no. 9, pp.
70415.
Lindner, J., J. Scheer, and H. Schmidt 1994, Stahlbauten, Erläuterungen zu DIN 18800,
Teil 1 bis Teil 4, 2nd edn, Beuth und Ernst & Sohn, Berlin.
Livesley, R.K. 1975, Matrix Methods of Structural Analysis, 2nd edn, Pergamon Press,
UK.
Livesley, R.K. and D.B. Chandler 1956, Stability Functions for Structural Frameworks,
Manchester University Press, Manchester, UK.
Llewellyn, D.T. and R.C. Hudd 1998, Steels: Metallurgy and Application, 3rd edn,
ButterworthsHeineman, p. 400.
Loov. R. and N. Parthasarathi 2004, Study of shear provisions for stiffened plate girders,
Canadian Journal of Civil Engg., vol. 31, pp. 1607.
Lu, L.W., H. Kamalvand 1968, Ultimate strength of laterally loaded columns, Journal
Lu, W. and P. Maekelaeinen 2003, Advanced Steel Structures (1. Structural Fire Design,
2. Fatigue Design), Laboratory of Steel Structures, Publication no. TKK TER
29, Helsinki University of Technology, Finland, p. 116.
Lui, E.M. 1992, A novel approach to K-factor determination, Engineering Journal,
AISC, vol. 29, no. 3, 3rd qtr, pp. 1509.
Lui, E.M. and W.F. Chen 1986, Frame analysis with panel zone deformation,
International Journal of Solids and Structures, vol. 22, no. 12, pp. 15991627.
Lwin, M.M. 2002, High Performance Steel -Designers Guide, 2nd edn, Department of
Transportation, San Francisco, USA, http://www.steel.org/infrastructure/bridges/
high-performance/hps-designersguide/intro.htm), 30 November 2004.
Lynn, B.A. and Stathopoulos 1995, Wind induced fatigue on low metal buildings,
MacGinley, T.J. 1997, Steel Structures: Practical Design Studies, 2nd edn, E&FN Spon,
London.
MacGinley, T.J. and P.T.C. Ang 1992, Structural Steelwork: Design to Limit State Theory,
ButterworthsHeinemann, Oxford, UK.
Machacek, J. and M. Tuma 2006, Fatigue life of girders with undulating web, Journal
of Constructional Steel Research, vol. 62, pp. 16877.
MacLeod, I.A. 1990, Analytical Modeling of Structural Systems: An Entirely New
Approach with Emphasis on Behaviour of Building Structures, Ellis Horwood,
NY, p. 222.
Maddox, S.J. 2005, Fatigue Strength of Welded Structures, 3rd edn, Abington Publishing,
Cambridge, England.
Madhu Mohan, V., P. Devadas Manoharan, and A.R. Santhakumar 2002, Towards a
Consistent Design Criteria for the Transforming Indian Structural Steel Design
Methodology, All India Seminar on Modern Trends in Steel Structures, February
8-9, Nagpur, pp. 92101.
Madsen, H.O., S. Krenk, and N.C. Lind 1986, Methods of Structural Safety, Prentice-
Hall, Englewood Cliffs, NJ.
Madugula, M.K.S. and S. Mohan 1988, Angles in eccentric tension, Journal of
Structural Engineering, ASCE, vol. 114, no. 10, pp. 238796.
Madugula, M.K.S., and J.B. Kennedy 1985, Single and Compound Angle Members:
Structural Analysis and Design, Elsevier Applied Science, London, England.
Mahadevan, K., B.N. Sridhara, and V. Kalyanaraman 1995, Buckling strength of core
loaded sleeved column systems in water tank staging, International Conference
on Stability of Structures, ICSS 95, Coimbatore, India, pp. 44151.
Mahendran, M. and C. Moor 1999, Three-dimensional modeling of steel portal frame
buildings, Journal of Structural Engineering, ASCE, vol. 125, no. 8, pp. 8708.
Manuel, T.J. and G.L. Kulak 2000, Strength of joints that combine bolts and welds,
Journal of Structural Engg., ASCE, vol. 126, no. 3, pp. 27987.
Maquoi, R. 1992, Plate Girders in Constructional Steel: DesignAn International
Guide, P.J. Dowling, J.E. Harding, and R. Bjorhovde (eds), Elsevier Applied
Science, London, pp. 13373.
Maquoi, R. and J. Rondal 1978, Mise en equation des nouvelles courbes europeennes
de flambement, Construction Metallique, Paris, no. 1.
Maquoi, R. and M. Skaloud 2000, Stability of plates and plated structures: General
report, Journal of Constructional Steel Research, vol. 55, no. 13, pp. 4568.
Marino, F.J. 1966, Ponding of two-way roof systems, Engineering Journal, AISC,
vol. 3, no. 3, pp. 93100.
Marshall, P.W. 1991, Design of Welded Tubular Connections: Basis and Use of AWS
Code Provisions, Elsevier, p. 412.
Marshall, W.T. and H.M. Nelson 1990, Structures, Longman, Essex, UK, pp. 79106.
Martin, L.H. and J.A. Purkiss 1992, Structural Design of Steel Work to BS 5950, Edward
Arnold, A division of Hodder and Stoughton, London, p. 468.
Massonet, C. 1959, Stability considerations in the design of steel columns, Journal of
Structural Div., ASCE, vol. 85, pp. 75111.
Massonnet, Ch. 1976, Forty Years of Research on BeamColumns in Steel, SM
Archives, North Holland Publishing Co., Amsterdam, vol. 1, pp. 27157.
References R.27
Massonnet, Ch. and R. Maquoi 1978, Recent Progress in the Field of Structural Stability
of Steel Structures, IABSE Surveys S-5/78, IABSE Periodica, pp. 140.
Mathews, M.S. and P.S. Rao 1979, Corrugated Ferrocement Sheets, ACI SP-61,
American Concrete Institute, Detroit, MI.
Mathews, M.S., M.S. Venugopal, and N. Subramanian 1977, Planning and Design of
Houses in Disaster Areas, International Conference on Disaster Area Housing,
Turkey.
Mathur, N.C. 2000, Stainless Steel in Architecture, Building and Construction, Steel
in Construction 2000, Joint Plant Committee, Govt. of India, pp.17993.
Matsushima, I. 1997, Corrosion Protection of Steel Bridge, Steel Today & Tomorrow,
no. 139, pp. 9-10.
Mazzolani (ed.) 2000, Moment Resistant Connections of Steel Frames in Seismic Areas:
Design and Reliability, E & FN Spon, London, p. 644.
Mazzolani, F.M. and V. Piluso 1996, Theory and Design of Seismic Resistant Steel
Frames, E & FN Spon, p. 544.
McCormac, J.C. and J.K. Nelson 2002, Structural Steel Design: LRFD Method, 3rd
edn, Prentice-Hall, Englewood Cliffs, NJ, p. 736.
McGuire, W. 1968, Steel Structures, Prentice-Hall, Englewood Cliffs, NJ, p. 31028.
McGuire, W., R.H. Gallagher, and R.D. Ziemian 2000, Matrix Structural Analysis, 2nd
edn, John Wiley, NY, p. 460.
Mehta, K.C. and J. Delahay 2003, Guide to the Use of the Wind Load Provisions of
ASCE 7-02, ASCE Press, Reston, VA.
Melinek, S.J. 1989, Prediction of the fire resistance of insulated steel, Fire Safety
Journal, vol. 14, pp. 12734.
Melinek, S.J. and P.H. Thomas 1987, Heat flow to insulated steel, Fire Safety Journal,
vol. 12, pp. 18.
Minor, J.E. 1982, Tornado technology and professional practice, Journal of Structural
Div., ASCE, vol. 108, no. 11, pp. 241122.
Mohammadi, J. (ed.) 2004, NDT Methods Applied to Fatigue Reliability Assessment of
Structures, ASCE/SEI, Reston, VA, p. 159.
Morris, L.J. 1981, A commentary on portal frame design, The Structural Engineer,
vol. 59A, no. 19, pp. 394402.
Morris, L.J. and D.R. Plum 1996, Structural Steelwork Design to BS 5950, 2nd edn,
Addison Wesley Longman, Essex, UK.
Morris, W.A., R.E.H. Read, and G.M.E. Cooke 1988, Guidelines for the Construction
of Fire Resisting Structural Elements, Building Research Establishment, UK.
Mullett, D.L. 1991, Slim-Floor Construction, The Steel Construction Institute, UK, p.
100.
Munse, W.H. 1956, Research on bolted connections, Transactions, ASCE, vol. 121,
pp. 125566.
Munse, W.H. and E. Chesson Jr. 1963, Riveted and bolted joints: Net section design,
Murray, T.M. 1990, Extended End-plate Moment Connections, Steel Design Guide
Series 4, American Institute of Steel Construction, Chicago.
Murray, T.M. 1991, Building Floor Vibrations, Engineering Journal, AISC, vol. 28,
no. 3, 3rd qtr, pp. 10209 (Errata, vol. 28, no. 4, 4th qtr, p. 176).
Murray, T.M., D.E. Allen, and E.E. Ungar 1997, Floor Vibrations due to Human Activity,
Steel Design Guide no. 11, American Institute of Steel Construction, Chicago, IL.
Murthy, A.R.C., G.S. Palani, and N.R. Iyer 2004, State of-the-art review on fatigue
crack growth analysis under variable amplitude loading, Journal of the Institution
of Engineers (India), Civil Engg. Div., vol. 85, pp. 11829.
Murty, C.V.R. 2004, IITK-BMTPC Earthquake Tips, www.nicee.org/EQTips/.php, 20
March 2006.
Naeim, F. and J.M. Kelly 1999, Design of Seismic Isolated Structures: From Theory
to Practice, John Wiley, NY, p. 304.
Nagoya T. 1998, Stainless Steel as Exterior Construction Material, Steel Today &
Tomorrow, no. 141, p. 58.
Narayanan, R,et.al, Plate girders I and II, Chapters 15,16 and 28, Teaching resources
for structural steel design, INSDAG, Kolkata, 2000.
Narayanan, R. (ed.) 1982, Axially Compressed Structures: Stability and Strength, Elsevier
Applied Science Publishers, Essex, England.
Narayanan, R. (ed.) 1983, Beams and Beam Columns: Stability and Strength, Applied
Science Publishers, Barking, Essex, England.
Narayanan, R. (ed.) 1983, Plated Structures: Stability and Strength, Elsevier Applied
Science Publishers, London.
Narayanan, R. and N.G.V Avanessian 1985, Design of slender webs having rectangular
holes, Journal of Structural Engineering, ASCE, vol. 111, no. 4, pp. 77787.
Narayanan, R. and T.M. Roberts (eds) 1990, Structures Subjected to Repeated Loading:
Stability and Strength, Spon Press, UK, p. 291.
Narayanan, R., P. Usha, and S.S. Rao 2003, Design of hot-rolled steel I-beams subjected
to torsion and bending, Paper circulated at IS: 800 review committee meeting, IIT
Madras.
Narayanan, S. and M.S. Mathews 2003, Behaviour of roofing sheet system under static
uplift loads, Journal of Institution of Engineers (India), Civil Engg. Div., vol. 84,
pp. 21622.
Nash, P. and R.A. Young 1978, Sprinklers in High Rise Buildings, BRE Current Paper,
CP 29/78, Building Research Establishment, Watford, UK.
National Building Code of India Part IV, Fire Protection, Indian Standards Institution,
New Delhi, 2005, www.iitk.ac.In/nicee/iitk-Gsdma/F03.pdf, 20 March 2006.
NAVFAC 1982, Foundations and Earth Structures, Design Manual 7.2, Naval Facilities
Engineering Command, Dept. of Navy, Alexandria, Virginia, USA.
Nazir, C.P. 2003, Prestressed steel arch bridge, Journal of the Institution of Engineers
(India), Civil Engg. Div., vol. 84, pp. 726.
Neal, B.G. 1977, The Plastic Methods of Structural Analysis, 3rd edn, Chapman &
Hall, London, p. 358.
Neis, V.V. 1985, New constitutive law for equal leg fillet welds, Journal of the Structural
Nethercot, D.A. 1973a, Lateral Buckling of Tapered Beams, Publications, IABSE,
vol. 33, part-II, pp. 17392.
Nethercot, D.A. 1973b, The Effective Lengths of Cantilevers as Governed by Lateral
Buckling, The Structural Engineer, vol. 51, pp. 1618.
Nethercot, D.A. 1974, Imperfections and the Design of Steel Beams, Proc., Institution
of Civil Engineers, vol. 57, pp. 291306.
References R.29
Nethercot, D.A. 1983, Elastic lateral buckling of beams, in Beams and Beam Columns:
Stability and Strength, R. Narayanan (ed.), Applied Science Publishers, Essex,
England.
Nethercot, D.A. 1992, Beams, in Constructional Steel Design: An International Guide,
P.J. Dowling, J.E. Harding, and R. Bjorhovde (eds), Elsevier Applied Science,
London/NY, pp. 4565.
Nethercot, D.A. 2001, Limit States Design of Structural Steelwork, 3rd edn, Spon Press,
London, p. 270.
Nethercot, D.A. and D. Kerdal 1982, Lateral Torsional Buckling of Castellated Beams,
The Structural Engineer, vol. 60B, no. 3, pp. 5361.
Nethercot, D.A. and K.C. Rockey 1972, A unified approach to the elastic lateral buckling
of beams, Engineering Journal, AISC, vol. 9, no. 3, pp. 96107.
Nethercot, D.A. and N.S. Trahair 1975, Design of diaphragm-braced I-beams, Journal
Nethercot, D.A. and N.S. Trahair 1976, Lateral Buckling Approximations for Elastic
Beams, The Structural Engineer, vol. 56, no. 6, pp. 197204.
Nethercot, D.A., P.R. Salter, and A.S. Malik 1989, Design of Members Subjected to
Torsion and Bending, The Steel Construction Institute, Ascot, England.
Newman, A. 2004, Metal Building Systems: Design and Specifications, 2nd edn,
Newman, G.M. 1990, Fire and Steel Construction: The Behaviour of Steel Portal Frames
with different Boundary Conditions; 2nd edn, The Steel Construction Institute,
Publication no. 87, Ascot, England.
Newmark, N.M. and E. Rosenbleuth 1971, Fundamentals of Earthquake Engineering,
Prentice-Hall, Upper Saddle River, NJ.
NZS 3404-1997, Steel Structures Standard, Parts 1 and 2, Standards New Zealand,
Wellington, 1997.
OCorner, M.A. and D.M. Martin 1998, Behaviour of a Multi-storey Steel Framed
Building Subjected to Fire Attack, Journal of Constructional Steel Research, vol.
46, no. 13.
ORourke, M. and C. Downey 2001, RainonSnow Surcharge for Roof Design,
ORourke, M. and M. Auren 1997, Snow Loads on Gable Roofs, Journal of Structural
ORourke, M. and P.D. Wrenn 2004, Snow loads: A Guide to the Use and Understanding
of Snow Load Provision of ASCE 7-02, ASCE Press, Reston, VA, p. 128.
Oehlers, D.J. and M.A. Bradford 1995, Composite Steel and Concrete Structural
Members, Fundamental Behaviour, Pergamon Press, Elmsord, NY.
Ojalvo, M. and R.S. Chambers 1977, Effect of warping restraints on I-beam buckling,
Orbison, J.G. and R.D. Ziemian 1995, Assessment of American block shear load capacity
predictions, Journal of Constructional Steel Research, vol. 35, pp. 32338.
Owens, G.W. and B.D. Cheal 1989, Structural Steelwork Connections, Butterworths,
London, p. 330.
Owens, G.W., P.J. Driver, and G.J. Kriege 1981, Punched holes in structural steel-
work, Journal of Constructional Steel Research, vol. 1, no. 3.
Packer, J.A. and J.E. Henderson 1997, Hollow Structural Section Connections and
Trusses: A Design Guide, 2nd edn, Canadian Institute of Steel Construction, Toronto,
Canada, p. 464.
Paik, J.K. and A.K. Thayamballi 2003, Ultimate Limit State Design of Steel Plated
Structures, John Wiley, England, p. 544.
Pandia Raj, R. and V. Kalyanaraman 2005, GA based optimal design of steel truss
bridge, 6th World Congress of Structural and Multi-disciplinary Optimization,
Rio de Janeiro, 30 May3 June, Brazil.
Pannel, J.P.M. 1964, An Illustrated History of Civil Engineering, Thames and Hudson,
London, UK.
Papangelis, J.P. and N.S. Trahair 1987, Flexural torsional buckling of arches, Journal
of Structural Engg., ASCE, vol. 113, no. ST7, pp. 143343.
Parfitt, J. Jr. and W.F. Chen 1976, Tests of welded steel beam-to-column connections,
Pasternak, H., A. Schwarzlos, and N. Schimmack 2004, The application of adhesives
to connect steel members, Journal of Constructional Steel Research, vol. 60, pp.
64958.
Paul, D.K. 2006, IIT Roorkee, private communication.
Paulay, T. and M.J.N. Priestley 1992, Seismic Design of Reinforced Concrete and
Masonry Buildings, John Wiley, NY, p. 744.
Paz, M. 1991, Structural Dynamics: Theory and Computations, 3rd edn, Van Nostrand
Reinhold, NY.
Petersen, Ch. 1980, Statik und Stabilität der Baukonstruktionen, Friedr. Vieweg & Sohn,
Braunschweig/Wiesbaden, Germany, p. 960.
Petersen, Ch. 1990, Stahlbau-Grundlagen der Berechnung und baulichen Ausbuildung
von Stahlbauten, 2nd edn, Vieweg Verlag, Braunschweig, p. 1413.
Petterson, O. 1973, Principles of Fire Engineering Design and Fire Safety of Tall
Buildings, Lund Institute of Technology Bulletin 31, Lund Sweden.
Petterson, O., S.E. Magnusson, and J. Thor 1976, Fire Engineering Design of Steel
Structures, Swedish Institute Of Steel Construction, Stockholm, Sweden, Publication
no. 50.
Pi, Y.L. and N.S. Trahair 1994, Inelastic bending and torsion of steel I-beam, Journal
of Structural Engineering, ASCE, vol. 120, no. 1, pp. 33973417.
Pi, Y.L. and N.S. Trahair 1994, Nonlinear inelastic analysis of steel beam-columns
Part I: Theory, Journal of Structural Engineering, ASCE, vol. 120, no. 7, pp.
204161 (see also Part II: Applications, pp. 206285).
Pi, Y.L. and N.S. Trahair 1995, Inelastic torsion of steel I-beams, Journal of Structural
Pillai, U. 1981, An assessment of CSA Standard equation for beam-column design,
Canadian Journal of Civil Engineering, vol. 8.
Pimple, P.K., A.C. Anturkar, and G.N. Ronghe 2002, Structural Steel Corrosion and its
Prevention, All India Seminar on Modern Trends in Steel Structures, Nagpur,
February 8-9, pp.12937.
Porter, D.M., K.C. Rockey, and H.R. Evans 1975, The Collapse of Plate Girders Loaded
in Shear, The Structural Engineer, vol. 53, no. 8, pp. 31325.
References R.31
Proe, D.J., I.D. Bennets, and I.R. Thomas 1968a, Simulation of the Fire Testing of
Structural Steel Elements by Calculation-Mechanical Response, Steel Construction,
vol. 19, no. 4, pp. 218.
Proe, D.J., I.D. Bennets, and I.R. Thomas 1986b, Simulation of the Fire Testing of
Structural Steel Elements by Calculation-Overall Behaviour, Steel Construction,
vol. 19, no. 4, pp. 1932.
Purkiss, J.A. 1996, Fire Safety Engineering Design of Structures, Butterworth
Heinemann, Oxford, England, p. 342.
Radaj, D. 1990, Design and Analysis of Fatigue Resistant Welded Structures, Abington
Publishing, Woodhead Publishing Ltd., in association with the Welding Institute
Cambridge, England.
Radhakrishnan, R. and N. Subramanian 1978, Dynamic Analysis of Multi-storey Frames
(A comparison of various methods), Bulletin, Indian Society of Earthquake
Technology, vol. 15, no. 3, pp. 3949.
Radhakrishnan, R., N. Subramanian, and C.R. Amalnarayanan 1979, Dynamic Analysis
of Offshore Structures, Journal of Structural Engineering, vol. 6, no. 4, pp. 213
8.
Ragupathi, M. 1995, Design of Steel Structures, Tata-McGraw Hill, New Delhi, p. 727.
Rains, N.A. 1976, A New Era of Fire Protective Coatings for Steel, Civil Engineering,
ASCE, pp. 803.
Rajeev, S. and C.S. Krishnamoorthy 1997, Generic algorithms-based methodology for
design optimization of trusses, Journal of Structural Engg., ASCE, vol. 123, no.
3, pp. 3508.
Ramachandra Murthy, D.S. et al. 1994, Corrosion fatigue of stiffened offshore steel
tubular joints, Journal Of Structural Engineering, ASCE, vol. 120, no. 7, pp.1991
2010.
Ramachandra Murthy, D.S. 1998, Fatigue Resistant Design of Steel Structures, Advance
Course on Design of Steel Structures, The Structural Engineering Research Centre,
Chennai, India.
Ramachandra Murthy, D.S. and S. Seetharaman (ed.) 1997, Advance Course on Fatigue
Resistant Design of Components and Structures, SERC, Madras, December 17
19.
Ramasamy, J.V. and S. Rajasekaran 1996, Artificial Neural Network and Generic
Algorithm for the Design Optimization of Industrial RoofsA Comparison,
Ramsden, J.D. 1993, Tsunamis: Forces on a Vertical Wall Caused by Long Waves,
Bores, and Surges on a Dry Bed, Report no. KH-R-54, W.M. Keck Laboratory,
California Institute of Technology, Pasadena, California, p. 251.
Ranganathan, R. 1990, Reliability Analysis and Design of Structures, Tata-McGraw
Hill, New Delhi.
Rangwala, S.C., K.S. Rangwala, and P.S. Rangwala 1997, Engineering Materials, 22nd
edn, Charotar Publishing House, Anand.
Rasmussen, K. Jr. 2001, Full Range Stress-Strain Curves for Stainless Steel Alloys,
Research Report no. R811, Department of Civil Engineering, The University of
Sydney, p. 45.
Ravindra, M.K. and T.V. Galambos 1978, Load and resistant factor design for steel,
Redwood, R. and S.H. Cho 1993, Design of steel and composite beams with web
openings, Journal of Constructional Steel Research, vol. 25, pp. 2341.
Reese, L.C., W.M. Isenhower, and S.T. Wang 2005, Analysis and Design of Shallow
and Deep Foundations, John Wiley, NY, p. 608.
Regan and Salter 1984, Tests on welded-angle tension members, The Structural
Engineer, vol. 62B, no. 2, pp. 2530.
Rentschler, G.P., W.F. Chen, and G.C. Driscoll 1982, Beam-to-column web connection
details, Journal of the Structural Div., ASCE, vol. 108, no. ST2, pp. 303409.
Richard, R.M., J.D. Kriegh, and D.E. Hormby 1982, Design of single plate framing
connections with A307 bolts, Engineering Journal, AISC, vol. 19, no. 4, pp. 209
13.
Richard, R.M., P.E. Gillett, J.D. Kriegh, and A. Lewis 1980, The analysis and design
of single plate framing connections, Engineering Journal, AISC, vol. 17, no. 2,
pp. 3851.
Ricker, D.T. 1982, Tips for avoiding crane runway problems, Engineering Journal,
AISC, vol. 19, no. 4, pp. 181205.
Ricker, D.T. 1989, Cambering steel beams, Engineering Journal, AISC, vol. 26, no.
4, pp. 13642.
Ricker, D.T. 1989, Some practical aspects of column base selection, Engineering
Journal, AISC, vol. 26, no. 3, 3rd qtr, 1989, pp. 819.
Righiniotis, T.D., E.R. Lancaster, and R.E. Hobbs 2000, Fracture strength of a moment
resisting welded connection under combined loadingPart I: Formulation, Journal
of Constructional Steel Research, vol .56, pp. 1730 (see also Part II, Results,
2000, vol. 56, pp. 3145).
Roark, J.R. and W.C. Young 1975, Formulae for Stress and Strain, 5th edn, McGraw
Hill, NY.
Roberts, R. and A.W. Pense 1980, Basics in Failure Analysis of Large Structures,
Civil Engineering, ASCE, vol. 50, no. 7, pp. 6062.
Roberts, T.M. 1981, Slender Plate Girders Subjected to Edge Loading, Proceedings,
Institution of Civil Engineers, Part 2, vol. 71, pp. 80519.
Roberts, T.M. and A.C.B. Newark 1997, Strength of webs subjected to compressive
edge loading, Journal of Structural Engineering, ASCE, vol. 123, no. 2, pp. 176
83.
Robertson, A. 1925, The Strength of Struts, ICE Selected Engineering Paper 28.
Rockey, K.C. and M. Skaloud 1971, The Ultimate Load Behaviour of Plate Girders
Loaded in Shear, IABSE Colloquium, Design of Plate and Box Girders for Ultimate
Strength, vol. II, London, pp. 119.
Rockey, K.C., G. Valtinat, and K.H. Tang 1981, The Design of Transverse Stiffeners
on Webs Loaded in ShearAn Ultimate Load Approach, Proceedings Institution
of Civil Engineers, Part 2, vol. 71, no. 2, pp. 106999.
Rockey, K.C., H.R. Evans, and D.M. Porter 1978, A Design Method for Predicting
Collapse Behaviour of Plate Girders, Proceedings of the Institution of Civil
Engineers, vol. 65, pp. 85112.
Roeder, C.W. and R.H. Dailey 1989, The results of experiments on seated beam
connections, Engineering Journal, AISC, vol. 26, no. 3, 3rd qtr, pp. 9095.
Roik, K. and R. Bergmann 1992, Composite columns in Constructional Steel Design,
P.J. Dowling et al. (eds), Elsevier Science Publishing, NY, pp. 44370.
References R.33
Roik, K., J. Carl, and J. Lindner 1972, Biege Torsions Probleme Gerader Dünnwandiger
Stäbe, Verlag von Wilhelm Ernst & Sohn, Berlin.
Rondal, J. and R. Maquoi 1979, Single equation for SSRC column-strength curves,
Roufaiel, M.S.L. and F.F. Monasa 1989, Microcomputer-aided analysis and design of
steel frames, Journal of Computing in Civil Engineering, ASCE, vol. 3, no. 2, pp.
12742.
Roytman, M.Ya. 1975, Principles of Fire Safety Standards for Building Construction,
Amerind Publishing, New Delhi, p. 429.
Ruddy, J. 1983, Economics of low-rise steel framed structures, Engineering Journal,
AISC, vol. 20, 3rd qtr, pp.10718.
Ruddy, J.L. 1986, Ponding of concrete deck floors, Engineering Journal, AISC, vol.
23, no. 3, pp. 10715.
Ruiz, S.E. and A.S. Trujillo 1997, Design live loads for classrooms in United States
and Mexico, Journal of Structural Engineering, ASCE, vol. 123, no. 12, pp. 1652
7.
Ruiz, S.E. and J.A. Soriano 1997, Design live loads for office buildings in Mexico and
USA, Journal of Structural Engineering, ASCE, vol. 123, no. 6, pp. 81622.
Rumpf, J.L. and J.W. Fisher 1963, Calibration of A325 bolts, Journal of the Structural
Sakimoto, T. and S. Komatsu 1983, Ultimate strength of arches with bracing systems,
Journal of Structural Div., ASCE, vol. 109, no. 3, pp. 61327.
Sakimoto, T. and T. Sakata 1982, Ultimate strength of arches with bracing systems,
Journal of Structural Div., ASCE, vol. 108, no. ST5, pp. 106476.
Sakimoto, T. and T. Sakata 1990, The out-of-plane buckling strength of through-type
arch bridges, Journal of Constructional Steel Research, vol. 16, pp. 30718.
Salem Steel Users Guide, Steel Authority of India, Salem Steel Plant, Salem, India,
1998, p. 48.
Salmon, C.G. and J.E. Johnson 1996, Steel Structures, Design and Behavior, 4th edn,
Harper Collins, NY, 1996, p. 1024.
Salmon, C.G., D.R. Buettner, and T.C. OSheridan 1964, Laboratory investigation of
unstiffened triangular bracket plates, Journal of the Structural Division, ASCE,
vol. 90, no. ST4, pp. 25778.
Salvadori, M.G. 1955, Lateral Buckling of I Beams, Transactions of the American
Society of Civil Engineers, vol. 120, pp. 116577.
Salvadori, M.G. 1956, Lateral Buckling of Eccentrically Loaded I-columns,
Samanta, A.K. 2003, Cathodic Protection of Steel Structures, in Course on Proposed
Revision of IS: 800, Institute for Steel Development and Growth (INSDAG),
Chennai, December 19-20, pp. 15.115.9.
Samanta, A.K. 2003b, Surface Protection of Steel Structures from Corrosion, in Course
on Proposed Revision of IS: 800, Institute for Steel Development and Growth
(INSDAG), Chennai, December 19-20, pp. 13.113.9.
Sarma, B.S. and N. Lakshmanan 1990, Evaluation of channel and tube purlins under
biaxial loading, Journal of Institution of Engineers, India, Civil Engg. Div., vol.
70, pp. 1539.
Sause, R., H.H. Abbas, R.G. Driver, K. Anami, and J.W. Fisher 2006, Fatigue life of
girders with trapezoidal corrugated webs, Journal of Structural Engineering,
ASCE, vol. 132, no. 7, pp. 10708.
Scawthorn, C., I. Eidinger, and A. Sehiff (ed.) 2005, Fire Following Earthquake, TCLEE
Monograph 26, American Society of Civil Engineers, Reston, VA, p. 352.
Schechter, M.M., E. Schechter, and E. Simiu 1995, Developmental computer-based
version of ASCE 7-95 Standard Provision for Wind Loads, NIST Tech. Note 1415,
National Institute of Standards and Technology, Gaithersburg, MD.
Schilling, C.G. 1968, Design of hybrid steel beams, Report of the Subcommittee 1 on
Beams and Girders, Joint ASCE-AASHO Committee on Flexural Members, Journal
Schilling, C.G. 1974, Optimum proportions for I-shaped beams, Journal of the
Schittich, C. 2001, In Detail: Building Skins, Concepts, Layers, Materials, Birkhouser,
Switzerland, p. 120.
Schodek, D.L. 2001, Structures, 4th edn, Prentice-Hall, Upper Saddle River, NJ, p.
581.
SEAOC 1980, Recommended Lateral Force Requirements and Commentary, Structural
Engineers Association of California.
Seetharaman, S., N. Pandian, and A. Jayachandran 2003, Advanced Analysis Techniques
for Steel FramesAn Overview, Proceeding of the Structural Engg. Convention,
IIT Kharagpur, pp. 8594.
Segui, W.T. 1999, LRFD Steel Design, 2nd edn, PWS Publishing, NY.
SEI/ASCE 24-98, Flood Resistant Design and Construction, Structural Engineering
Institute/American Society of Civil Engineering, Reston, VA, 2000, p. 72.
SEI/ASCE 37-02, Design Loads on Structures during Construction, Structural
Engineering Institute/American Society of Civil Engineers, Reston, VA, 2002.
SEI/ASCE 7-05, Minimum Design Loads for Buildings and Other Structures, American
Society of Civil Engineers, Reston, VA, 2006, p. 376.
Seilie, I.F. and J.D. Hooper 2005, Steel plate shear walls: Practical design and
construction, Modern Steel Construction, AISC, vol. 45, no. 4, pp. 3742.
Serna, M.A., A. Lopez, I. Puente, and D.J. Yong 2006, Equivalent uniform moment
factors for lateral torsional buckling of steel members, Journal of the Constructional
Steel Research, vol. 62, no. 6, pp.56680.
Sfintesco, D. 1970, Experimental Basis of the European Column Curves, Construction
Metallique, no. 3, p. 5.
Shanley, F.R. 1946, The column paradox, Journal of the Aeronautical Sciences, vol.
13, no. 12, p. 678.
Shanley, F.R. 1947, Inelastic column theory, Journal of the Aeronautical Science,
vol. 14, no. 5, pp. 2614.
Shanmugam, N.E. and C.M. Wang 2006, Analysis and Design of Plated Structures
Vol. 1: Stability, CRC Press, UK, p. 498.
Shanmugam, N.E., J.Y.R Liew, and S.L. Lee 1993, Ultimate strength design of biaxially
loaded steel box beam-columns, Journal of Constructional Steel Research, vol.
26, no. 2&3, pp. 99123.
Sharp, M.L. and J.W. Clark 1971, Thin aluminum, shear webs, Journal of the Structural
References R.35
SHS Design Manual for Concrete Filled Columns: Part 2: Fire Resistant Design, British
Steel, UK, 1996.
Simiu, E. and R.H Scanlan 1996, Wind Effects on Structures: Fundamentals and
Applications to Design, 3rd edn, Wiley InterScience, NY, p. 704.
Sivakumaran, K.S. 1988, Seismic Response of Multi-storey Steel Building with Flexible
Connections, Engineering Structures, vol. 10, pp. 23948.
Skinner, R.I., W.H. Robinson, and G.H. McVerry 1993, An Introduction to Seismic
Isolation, John Wiley, NY, p. 376.
Smith, B.S. and A. Coull 1991, Tall Building Structures: Analysis and Design, Wiley
Inter Science Publication, NY.
Socie, F. and G.B. Marquis 2000, Multiaxial Fatigue, Society of Automotive Engineers
(SAE) Inc., Warrendale, PA.
Soong, T.T. and G.F. Dargush 1997, Passive Energy Dissipation Systems in Structural
Engineering, John Wiley, NY, p. 368.
Sputo, T. 1993, History of steel beam-column design, Journal of Structural
Sree Ramachandra Murthy, D., D. Bhanu Prasad, K.V. Ramesh, and D.L. Narasimha
Rao 2004, Economical Aspects in the Design of Steel Trusses, Civil Engineering
and Construction Review, vol. 17, no.1, pp. 3038.
Sreevidya, S. and N. Subramanian 2003, Aesthetic appraisal of antenna towers, Journal
of Architectural Engineering, ASCE, vol. 9, no. 3, pp. 1038.
Sridhara, B.N. 1991, Design of Optimum Weight Compression Members, International
Conference on Steel and Aluminium Structures, Singapore, pp. 298307.
Srinivasa Rao, P. and G.S. Krishnamurthy 1993, Imposed loads on floors of office
buildings: Results of load survey, Indian Concrete Journal, vol. 67, no. 11, pp.
53844.
Standard Specifications for Open Web Steel Joists: K-Series, 41st edn, Steel Joist
Institute, Myrtle Beach, SC, 2002.
Steel Construction Guide book: Building Construction and Civil Engineering, The Kozai
Club, Japan, 1983.
Steel Today and Tomorrow, News of Japanese steel, No.43-46, Sept 82, Dec 82, Mar.,
83 and June 83, No.107, Oct-Dec 1989.
Steinhardt, O. and W. Schröter 1971, Post Critical Behaviour of Aluminium Plate Girders
with Transverse Stiffeners, IABSE Colloquium, Design of Plate and Box girders
for Ultimate Strength, London.
Structural Fire Design: Off-Site Applied Thin Film Intumescent Coatings, Report no.
433, Steel Construction Institute, UK, 1996.
Struik, J.H.A., A.O. Oyeledun, and J.W. Fisher, 1973, Bolt tension control with a direct
tension indicator, Engineering Journal, AISC, vol. 10, no. 1, 1st qtr, pp. 15.
Subramanian, N. (ed.) 1983, First National Seminar on Computers and Civil
Engineering, November 26, Organized by Computer Design Consultants, Madras.
Subramanian, N. (ed.) 1991, National Seminar on Computers in Civil Engineering,
Organized by the Association of Consulting Civil Engineers, Chennai.
Subramanian, N. 1974, Plastic Design of Minimum Weight Frames by Moment
Distribution, M. Sc. Thesis, University of Madras, p. 164.
Subramanian, N. 1974, Safety in Engineering Structures, Fourth National Conference
on Industrial Safety, College of Engineering, Guindy, Chennai.
Subramanian, N. 1982, Lateral Torsional Buckling Problem of Cold-formed Members

with Section Deformation, Report No. VR 2039, Technical University of Berlin,
Germany, p. 74.
Subramanian, N. 1983, Recent Progress in the Field of Lateral Instability of Steel
Beams, The Bridge and Structural Engineer, vol. 13, no. 1, pp. 1747 (see also
no. 2, pp. 113).
Subramanian, N. 1984, Why Buildings Collapse?, Science Reporter, vol. 24, no. 5 &
6, pp. 2328.
Subramanian, N. 1984, Versuche an geschraubten Flanchverbindungen in L-Form,
Unpublished report, Lehrstuhl fuer Stahlbau, Der Universitaet Bundeswehr, Munich,
Germany.
Subramanian, N. 1986, P-Frame-User Manual for Plane Frame, Computer Design
Consultants, Chennai, India.
Subramanian, N. 1987, Aesthetics of Non-habitat Structures, The Bridge and Structural
Engineer, Journal of ING/IABSE, vol. 17, no. 4, pp. 75100.
Subramanian, N. 1989, Diagnosis of the Causes of Failures, The Bridge and Structural
Engineer, vol. 19, no. 1, pp. 2442.
Subramanian, N. 1990, Wind Loads on Industrial Buildings, Civil Engineering and
Construction Review, vol. 3, no. 12, pp. 4450.
Subramanian, N. 1991, Wind Load of Steel Microwave Towers: A Comparison of
Codes, Engineering Design, vol. XX, No. 182, pp. 1822.
Subramanian, N. 1992, Composite Floors Speed up Construction, Civil Engineering
and Construction Review, vol. 5, no. 1, pp. 18.
Subramanian, N. 1992, Design of Antenna Towers, The Bridge and Structural Engineer,
vol. XXII, no. 2, pp. 1532.
Subramanian, N. 1992, New Steel Beams Increase Efficiency and Reduce Costs, Civil
Engineering and Construction Review, vol. 5, no. 7, p. 29.
Subramanian, N. 1994, How to Build Earthquake Proof Structures, Civil Engineering
and Construction Review, vol. 7, no. 4, pp. 3941.
Subramanian, N. 1995, Computer Analysis and Design of Tall Structures, Civil
Engineering and Construction Review, vol. 8, no. 4, pp. 426.
Subramanian, N. 1995, Distorsional Buckling of Lipped Channel Beams, International
Conference on Stability of Structures, June 79, PSG College of Tech., Coimbatore.
Subramanian, N. 1998, Rehabilitation of Steel Structures: Some Case Studies, Advance
course on Design of Steel Skeletal Structures, December 1618, SERC, Chennai.
Subramanian, N. 1999, Improper detailing results in delayed commissioning, Journal
of Performance of Constructed Facilities, ASCE, vol. 13, no. 1, pp. 2933.
Subramanian, N. 1999, Principles of Space Structures, 2nd edn, Wheeler Publishing,
Allahabad, p. 666.
Subramanian, N. 2000, Corrosion Protection of Steel Structures, The Master Builder,
vol. 2, no. 1, pp. 636 (see also no. 2, pp. 147).
Subramanian, N. 2000, Recent developments in the design of anchor bolts, The Indian
Concrete Journal, vol. 74, no. 7, pp. 40714.
Subramanian, N. 2000, Restoration of Cold Storage Factory Building, Journal of
Performance of Constructed Facilities, ASCE, vol. 14, no. 4, pp. 1559.
References R.37
Subramanian, N. 2002, Collapse of WTC: Its impact on skyscraper construction, The

Indian Concrete Journal, vol. 76, no. 3, pp. 1659.
Subramanian, N. 2007, Space Structures: Principles and Practice, Multi-Science
Publishing Co. Ltd., Essex, UK.
Subramanian, N. and C. Ganapathy 1980, Computer Analysis of Space Frames with
Offset Members, Computers and Structures, vol. 11, pp. 297303.
Subramanian, N. and C. Petersen 1987, Behaviour of HSFG Bolts in Chimney Joints,
Third International Conference on Steel Structures, Singapore.
Subramanian, N. and C.C. Sampath 2002, Indias First Stainless Steel Space Frame
Roof, Fifth International Conference on Space Structures, University of Surrey,
England.
Subramanian, N. and M.R. Pranesh 1982, Fixed Pile Supported Steel Offshore
PlatformsOverview, Journal of Institution of Engineers (India), vol. 63, pt CI3,
pp. 1518.
Subramanian, N. and M.S. Venugopal 1976, Partial failures of some industrial sheds-
A case study, The Indian Concrete Journal, vol. 50, no. 5, pp. 143-4 & p. 159.
Subramanian, N. and M.S. Venugopal 1984, Fire Safety of Multi-Storied Buildings,
National Symposium On Building Services, March 1-2, Vigyan Bhavan, New Delhi.
Subramanian, N. and M.S. Venugopal 1998, Rehabilitation of a Fire Damaged Factory
Building, New Building Materials and Construction World, vol. 3, no. IX, pp. 15-
23.
Subramanian, N. and R.A. Cook 2002, Installation, behaviour and design of bonded
anchors, The Indian Concrete Journal, vol. 76, no. 1, pp. 4756.
Subramanian, N. and R.A. Cook 2004, Behaviour of grouted anchors, The Indian
Concrete Journal, vol. 78, no. 4, pp. 1421.
Subramanian, N. and S. Mangalam 1997, Distress to green houses due to improper
execution, Civil Engineering and Construction Review, vol. 10, no. 8, pp. 458.
Subramanian, N. and S. Mangalam 1998, Restoration of a factory building, Journal of
the Institution of Engineers (India), vol. 79, pp. 147.
Subramanian, N. and V. Vasanthi 1991, Design of Anchor Bolts in Concrete, The
Bridge and Structural Engineer, vol. XXI, no. 3, pp. 4773.
Suresh, S. 1998, Fatigue of Materials, 2nd edn, Cambridge University Press, Cambridge,
UK.
Swannel 1981, Rational design of fillet weld groups, Journal of the Structural Div.,
ASCE, vol. 107, no. ST5, pp. 789802.
Swiatek, D. and E. Whitbeck 2004, Anchor Rods, Modern Steel Construction, vol.
44, no. 12, pp. 313.
Szewczak, R.M., E.A. Smith, and J.T. DeWolf 1983, Beams with torsional stiffeners,
Takeuchi, T. 1964, Investigation of the Load Carrying Capacity of Plate Girders, M.S.
Thesis, University of Kyoto, Japan.
Tall, L. 1974, Structural Steel Design, Ronald Press, NY.
Tamboli, A.R. 1999, Handbook of Structural Steel Connection Design and Details,
Taranath, B.S. 1988, Structural Analysis and Design of Tall Buildings, Intl. edn, McGraw
Hill, NY.
Taranath, B.S. 1998, Steel, Concrete and Composite Design of Tall Buildings, 2nd edn,
Task Committee on Longitudinally Stiffened Plate Girders of the ASCE AASHTO
Committee on Flexural Members of the Committee on Metals of the Structural
Div. 1978, Theory and design of longitudinally stiffened plate girders, Journal of
the Structural Div., ASCE, vol. 104, no. ST4, pp. 697716.
Tebedge, N. and W.F. Chen 1974, Design criteria for H-columns under biaxial loading,
Temple, M.E. and S.S.S. Sakla 1994, Balanced and unbalanced welds for angle
compression members, Canadian Journal of Civil Engg., vol. 21, pp. 396403.
Thambiratnam, D.P. and P. Paramasivam 1986, Base plates under axial loads and
moments, Journal of Structural Engineering, ASCE, vol. 112, no. 5, pp. 1166
81.
Thandavamoorthy, T.S. 2005, Analysis of Structures: Strength and Behaviour, Oxford
University Press, New Delhi, p. 860.
The European Steel Design Education Programme (ESDEP), Lectures http://
www.kuleuven.be/bwk/materials/teaching/master/toc.htm, Katholieke Universiteit,
Department of Building Materials and Building Technology, Nederlands, 15 April
2006.
The Fire Resistance of Shelf Angle Floor Beams To BS: 5950 Part 8, Steel Construction
Institute, Ascot, UK, 1993.
The Fire Resistance Of Web Infilled Steel Columns, Steel Construction Institute, Ascot,
UK, 1992.
Theling, K.E. 1984, Steel and its Heat Treatment, Butterworths, London, UK.
Thornton, C.H. 1973, Quality control in design and supervision can eliminate lamellar
tearing, Engineering Journal, AISC, vol. 10, no. 4, 4th qtr, pp. 1126.
Thornton, W.A. 1985, Prying action: A general treatment, Engineering Journal, AISC,
vol. 22, 2nd qtr, pp. 6775.
Thornton, W.A. 1992, Strength and serviceability of hanger connections, Engineering
Journal, AISC, vol. 29, 4th qtr, pp. 1459.
Thornton, W.A. 1995, Connections-Art, Science and Information into the quest for
economy and safety, Engineering Journal, AISC, vol. 32, no. 4, 4th qtr, pp. 132
44.
Timoshenko, S.P. 1953, History of the Strength of Materials, McGraw Hill, NY.
Timoshenko, S.P. and J.M. Gere 1961, Theory of Elastic Stability, 2nd edn, McGraw
Hill, NY.
Timoshenko, S.P. and J.N. Goodier 1970, Theory of Elasticity, 3rd edn, McGraw Hill,
NY.
Timoshenko, S.P. and S.W. Krieger 1968, Theory of Plates and Shells, 2nd edn, McGraw
Hill, NY.
Trahair, N.S. 1993, Flexural-torsional Buckling of Structures, CRC Press, Boca Raton,
FL.
Trahair, N.S. 2001, Moment Capacities of Steel Angle Sections, Research Report no.
R809, Dept. of Civil Engineering, The University of Sydney, http://
www.civil.usyd.edu.au/, 29 November 2006.
References R.39
Trahair, N.S. and S.L. Chan 2003, Out-of-plane advanced analysis of steel structures,
Engineering Structures, vol. 25, pp. 162737.
Trahair, N.S. and Y.L. Pi 1996, Simplified Torsion Design of Compact I-beams, Steel
Construction, AISC, vol. 30, no. 1, pp. 219.
Trahair, N.S., M.A. Bradford, and D.A. Nethercot 2001, The Behaviour and Design of
Steel Structures to BS 5950, 3rd edn, Spon Press, London and NY, p. 448.
Troitsky, M.S. 1990, Prestressed Steel Bridges: Theory and Design, Von Nostrand
Reinhold Co., NY.
Twilt, L. et al. 1994, Design Guide for Structural Hollow Section Columns Exposed to
Fire, CIDECT, Paris.
Twilt, L., P. Van De Leur, L.G. Cajot, J.B. Schleich, D. Joyeux, and J. Kruppa 1996,
Input Data for the Natural Fire Design of Building Structures, IABSE Report:
Basis of Design and Actions on Structures, Background and Application of Eurocode
1, Switzerland.
Uang, C.W., S.W. Wattar, and K.M. Leet 1990, Proposed revision of the equivalent
axial load method for LRFD steel and composite beam-column design, Engineering
Unnikrishna Pillai, S. and P. Menon 2003, Reinforced Concrete Design, 2nd edn, Tata-
McGraw Hill, New Delhi.
Usha 2003, Analytical Study of Nonlinear Behaviour of Steel Angle Tension Members,
M.S. Thesis, IIT Madras.
Usha and V. Kalyanaraman 2002, Strength of Steel Tension Members, Proc. All India
Seminar on Modern Trends in Steel Structures, Nagpur, February 8-9, pp. 219.
Vacharajittiphan, P. and N.S. Trahair 1974, Warping and distortion at I-section joints,
Valitnat, G. 1982, Tragsicherheitsnachweise für spezielle trägerformen-vollwandträger
mit schlanken stegen und vertikalsteifen, Stahlbau Handbuch für Studium und
Praxis, Band 1, Stahlbau-Verlags GMBH, Köln, pp. 53142.
Varghese, P.C. and C. Ganapathy Chettiar 1974, Lateral stability of open web structures,
Vayas, I., A. Ciutina and A. Spiliopoulos 1999, Low cycle fatigue gesttzter erdbeben-
nachweis von rahmen aus stahl, Bauingenieur, vol. 74, pp. 44857.
Vayas, I., A. Sophocleous, and F. Dinu 2003, Fatigue analysis of moment resisting
steel frames, Journal of Earthquake Engineering, vol. 7, no. 4, pp. 63554.
Veljkovic, M. and B. Johansson 2004, Design of hybrid steel girders, Journal of
Constructional Steel Research, vol. 60, pp. 53547.
Venugopal, M.S. and N. Subramanian 1977, Differential Movements in Soils, Seminar
on Problems of Building Foundations, February 20, Chennai.
Vickery, P.J. and P.F. Skerlj 2005, Hurricane gust factors revisited, Journal of Structural
Viest, I.M., J.P. Cotaco, R.W. Furlong, L.G. Griffis, R.T. Leon, and L.A. Wyllie 1996,
Composite Construction: Design for Buildings, ASCE, McGraw Hill, NY.
Villettee, M., N. Boissonnade, J.P. Muzeau, J.P. Jaspart 2000, Development of
Comprehensive Formula for the Design of Beam-columns, Internal report, Baudin
Chateauneuf, LERMES-CUST, University of Liege, Netherlands.
Vinnakota, S. 1977, Inelastic stability of laterally unsupported beams, Computers and
Structures, vol. 7, no. 3.
Vinnakota, S. 2006, Steel Structures: Behavior and LRFD, McGraw Hill, NY, pp. 593
688.
Vinnakota, S. and P. Aysto 1974, Inelastic spatial stability of restrained beam- columns,
Vinnakota, S. and Y. Aoshima 1974, Spatial Behaviour of Rotationally and Directionally
Restrained Beam-columns, Publications of IABSE, vol. 34-II, pp. 16994.
Vogel, U. 1985, Calibrating frames, Der Stahlbau, vol. 10, pp. 17.
Vogel, U. and J. Lindner 1980, Kommentar zu DIN: 18800, Teil 2 (Gelbdruck),
Stabilitatsfalle im Stahlbau, Knicken von Staben und Stabwerken, DASt. H.11,
Stahlbau Verlag, Köln.
Von Karman, T. 1908, Die knickfestigkeit gerader Stäbe, Physicalische zeitschrift,
vol. 9, pp. 136.
Von Wingerde, A.M., J.A. Packer, and J. Wardenier 1995, Criteria for the fatigue
assessment of hollow structural section connections, Journal of Steel Research,
vol. 35, no. 1, pp. 71115.
Wainman, D.E. and B.R. Kirby 1988, Compendium of UK Standard Fire Test Data,
Unprotected Steel-1, British Steel Corporation, Swinden, UK.
Walpole, R.E. and R.H. Myers 1978, Probability and Statistics for Engineers and
Scientists, MacMillan, NY.
Walton, C. 1984, Cases of Structural Damage Attributed to Snow on Roofs in the UK,
Building Research Establishment, Note N 57/90, Watford, England.
Wang, C.K. 1973, Computer Methods in Advanced Structural Analysis, Intext
Educational Publishers, NY.
Wang, C.M. and S. Kitipornchai 1986, Buckling capacities of mono-symmetric I beams,
Journal of the Structural Div., ASCE, vol. 112, no. 11, pp. 237391.
Wang, M.B. 2005, Universal design charts for insulation of steel members in fire,
Journal Of Constructional Steel Research, vol. 61, no. 10, pp. 144756.
Wang, M.B. and N. Patterson 1996, Unit load factor method for limiting temperature
analysis of steel frames with elastic buckling failure mode, Fire Safety Journal,
vol. 27, pp. 11322.
Warner, J. 2004, Practical Handbook of Grouting: Soil, Rock and Structures, John
Wiley, NY, p. 720.
Weaver, W.M. 1979, Crane Handbook: Design, Data and Engineering Information
used in the Manufacture and Application of Overhead and Gantry Cranes, 4th
edn, Whiting Corporation, Harvey, IL.
Wen, Y.K. and G.L. Yeo 2001, Design live loads for passenger cars parking garages,
West, M.A., J.M. Fisher, and L.A. Griffis 2003, Serviceability Design considerations
for Steel Buildings, Steel Design Guide no. 3, 2nd edn, American Institute of Steel
Construction, Chicago, IL.
Whalen, T.M., S. Gopal, and D.M. Abraham 2004, Cost-benefit Model for the
Construction of Tornado Shelters, Journal of Construction Engineering and
Management, ASCE, vol. 130, no. 6, pp. 7729.
White, D.W. and J.F. Hajjar 1987, Application of second-order elastic analysis in LRFD:
research to practice, Engineering Journal, AISC, vol. 24, no. 4, pp. 13348.
References R.41
White, D.W. and M.J. Clarke 1997, Design of beam-columns in steel framesPart I:
Philosophies and procedures and Part II: Comparison of standards, Journal of
Structural Engineering, ASCE, vol. 123, no. 12, pp. 155664, pp. 156575.
White, D.W. and W.F. Chen 1990, Second-order Inelastic Analysis for Frame Design,
V. Kalyanaraman (ed.), Proc. of the National Symposium on Advances on Steel
Structures, February 79, IIT Madras, Tata-McGraw Hill.
Whitmore, R.E. 1952, Experimental Investigation of Stresses in Gusset Plates, Bulletin
No. 16, Engineering Experiment Station, University of Tennessee, USA.
Wiegel, R.L. 1964, Oceanographical Engineering, Prentice-Hall, Englewood Cliffs,
NJ, p. 532.
Williams, A. 2004, Seismic Design of Building and Bridges, 3rd edn, Engineering Press,
California.
Winter, G. 1947, Strength of Thin Steel Compression Flanges, Transactions of ASCE,
vol. 112, p. 527.
Winter, G. 1960, Lateral Bracing of Columns and Beams, Transactions of ASCE, vol.
125, pt 1, pp. 80925.
Witteveen, J., J.W.B. Stark, F.S.K. Bijlaard, and P. Zoetemeijer 1982, Welded and
bolted beam-to-column connections, Journal of the Structural Div., ASCE, vol.
108, no. ST2, pp. 43355.
Wolmuth, B. and J. Surtess 2004, Crowd Related Failures of Bridges, Civil Engineering
Proceedings of ICE, vol. 156, Issue 3, pp. 11623.
Wood, R.H. 1974, Effective Lengths of Columns in Multistory Frames, The Structural
Engineer, vol. 52, no. 7, pp. 23544 (see also no. 8, pp. 295302 and no. 9, pp.
3416).
Wood. R.H. 1973, Rigid-jointed Multi-storey Steel Frame Design: A State of the Art
Report, Building Research Establishment, Current Paper CP 25/73, Watford,
England.
Woolcock, S.T. and S. Kitipornchai 1987, Design of single angle web struts in trusses,
www.Corrosion-doctors.org , 15 Dec 2004.
www.dot.ca.gov/hq/esc/construction/manuals/trenching and shoring/Ch3_soil.pdf
www.engineersedge.com/weld_design_menu.shtml (provides welded joint design
equations and calculations).
www.euro-inox.org, 6 July 2006.
www.fatiguecalculator.com, May 2006.
www.ushamartin.com
Xu, Y.L. 1995, Fatigue performance of screw-fastened light-gauge steel roof sheets,
Journal of Structural Engineering, ASCE, vol. 121, no. 3, pp. 38998 (see also
Discussions 1996, vol. 122, no. 12, pp. 147583).
Yang, Y.B. and S.R. Quo 1994, Theory and Analysis of Nonlinear Framed Structures,
Prentice Hall, Upper Saddle River, NJ.
Yang, Y.B. and W. McGuire 1986, Stiffness matrix for geometric nonlinear analysis,
Journal of Structural Div., ASCE, vol. 112, no. 4.
Yeh, H., I. Robertson, and J. Preuss 2005, Development of Design Guidelines that
serve as Tsunami Vertical Evacuation sites, Report 2005-4, Washington State
Department of Natural Resources, Division of Geology and Earth Resources.
Young, T. 1807, A Course of Lectures on Natural Philosophy and Mechanical Arts, J.

Johnson, London, England.
Young, W.C. and R. Budynas 2001, Roarks Formulas for Stress and Strain, 7th edn,
McGraw-Hill Professional, NY, p. 832.
Yu, C.H. and N.E. Shanmugam 1986, Stability of Frames with Semi-rigid Joints,
Yu, C.K. and L. Tall 1971, Significance and application of stub column test results,
Yu, Q.S., S. Noel, and C.M. Uang 1997, Experimental and Analytical Studies on Seismic
Rehabilitation of Pre-Northridge Steel Moment Connections: RBS and Haunch
Approaches, Structural Engg. Div., Report no. SSRP-97/08, University of California,
San Diego.
Yu, W.W. 2000, Cold Formed Steel Design, 3rd edn, Inter Science, N.Y., p. 848.
Yura, J. 2001, Fundamental of beam bracing, Engineering Journal, AISC, vol. 38, no.
1, pp. 1126.
Yura, J.A. 1971, The effective length of columns in unbraced frames, Engineering
Journal, AISC, vol. 8, no. 2, pp. 3742 (see also Discussions 1972, vol. 9, no. 1,
pp. 40-41, 46, & pp. 167-8).
Yura, J.A. 1998, Elements for Teaching Load and Resistance Factor Design, University
of Texas at Austin, Texas, pp. 5571.
Yura, J.A., P.C. Birkemoe, and J.M. Ricles 1982, Beam web shear connections: An
Experimental study, Journal of the Structural Div., ASCE, vol. 108, no. ST2, pp.
31125.
Yura, J.A., T.V. Galambos, and M.K. Ravindra 1978, The bending resistance of steel
Zahn, C.J. 1987, Plate girder design using LRFD, Engineering Journal, AISC, vol.
24, no. 1, pp. 1120.
Zhao, X.L. et al. 2001, Design Guide for Circular and Rectangular Hollow Section
Welded Joints under Fatigue Loading, CIDECT and Verlag TÜV Rheiland GMBH,
Köln, Germany, p. 121.
Zhou, Y., T. Kijewski, and A. Kareem 2002, Along wind load effects on tall buildings:
Comparative study of major international codes and standards, Journal of Structural
Zicherman, J. 2003, Fire performance of foam-plastic building insulation, Journal of
Architectural Engineering, ASCE, vol. 9, no. 3, pp. 97101.
Ziemian, R.D., W. McGuire, and G.G. Deierlein 1992, Limit states steel design using
second-order inelastic analysis: Planar frame studies, and 3-D high rise frame study,
Zirakian, T. and H. Showkati 2006, Distortional buckling of castellated beams, Journal
of the Constructional Steel Research, vol. 62, no. 8.
Zum Brandverhalten Von Gesamtkonstruktionen Des Stahl-Und Stahlverbundbaus
Teil 1- 4, Der Stahlbau, vol. 62, JanuaryApril 1983.

References PDF

Uploaded by

Copyright:

Available Formats

References PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

References PDF

Uploaded by

Copyright:

Available Formats

References

Allen, D. 1978, MerchantRankine approach to member stability, Journal of Structural

20: Methods for the Determination of the Fire Resistance of Elements of

Chaudhari, B. and A.K. Samanta 2003, Corrosion Protection of Steel Structures by

Fisher, J.M. 1991, Industrial buildings, in Constructional Steel Design: An International

Krawinkler, H. and S. Mohasseb 1987, Effect of panel zone deformation on seismic

Lindner, J. 1980, Biegedrillknicken in Theorie, Versuch und Praxis, Berischte am

Subramanian, N. 1982, Lateral Torsional Buckling Problem of Cold-formed Members

Subramanian, N. 2002, Collapse of WTC: Its impact on skyscraper construction, The

Young, T. 1807, A Course of Lectures on Natural Philosophy and Mechanical Arts, J.

You might also like

References PDF

Uploaded by

Copyright:

Available Formats

References PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

References PDF

Uploaded by

Copyright:

Available Formats

References

Allen, D. 1978, MerchantRankine approach to member stability, Journal of Structural

20: Methods for the Determination of the Fire Resistance of Elements of

Chaudhari, B. and A.K. Samanta 2003, Corrosion Protection of Steel Structures by

Fisher, J.M. 1991, Industrial buildings, in Constructional Steel Design: An International

Krawinkler, H. and S. Mohasseb 1987, Effect of panel zone deformation on seismic

Lindner, J. 1980, Biegedrillknicken in Theorie, Versuch und Praxis, Berischte am

Subramanian, N. 1982, Lateral Torsional Buckling Problem of Cold-formed Members

Subramanian, N. 2002, Collapse of WTC: Its impact on skyscraper construction, The

Young, T. 1807, A Course of Lectures on Natural Philosophy and Mechanical Arts, J.

You might also like

Allen, D. 1978, MerchantRankine approach to member stability, Journal of Structural

Chaudhari, B. and A.K. Samanta 2003, Corrosion Protection of Steel Structures by

Fisher, J.M. 1991, Industrial buildings, in Constructional Steel Design: An International

Krawinkler, H. and S. Mohasseb 1987, Effect of panel zone deformation on seismic

Lindner, J. 1980, Biegedrillknicken in Theorie, Versuch und Praxis, Berischte am

Subramanian, N. 2002, Collapse of WTC: Its impact on skyscraper construction, The