Globe Valve

BOA-H/HE/HV/HEV
PN 25/40
DN 10-350
Bellows
Flanged/Butt Weld Ends
or Socket Weld Ends

Type Series Booklet

Legal information/Copyright
Type Series Booklet BOA-H/HE/HV/HEV

All rights reserved. The contents provided herein must neither be distributed, copied, reproduced,
edited or processed for any other purpose, nor otherwise transmitted, published or made available to
a third party without the manufacturer's express written consent.

Subject to technical modification without prior notice.

© KSB Aktiengesellschaft, Frankenthal 04.07.2016

 Globe Valves
Bellows-type globe valves to DIN/EN

Globe Valves Design details

Design

Bellows-type globe valves to DIN/EN

▪ Straight-way pattern
▪ On/off disc
BOA-H/HE/HV/HEV ▪ Seat/disc interface made of wear-resistant and corrosion-
proof chrome (Cr) steel or chrome nickel (CrNi) steel
▪ Outside screw
▪ Back seat
▪ Stem sealed by double-walled bellows and back-up gland
packing
▪ EC type-tested (Module B), component mark TÜ.A./AR-291
▪ Exterior coating: blue RAL 5002
▪ The valves meet the requirements specified in TA-Luft
(German Technical Guidelines on Air Quality Control,
VDI 2440).
▪ The valves satisfy the safety requirements of Annex I of
the European Pressure Equipment Directive 97/23/EC (PED)
for fluids in Groups 1 and 2.
▪ The valves do not have a potential internal source of
ignition and can be used in potentially explosive
atmospheres, Group II, category 2 (zones 1+21) and
category 3 (zones 2+22) to ATEX 2014/34/EU.

Variants
▪ Throttling plug

Main applications ▪ Balanced plug for DN 250-350 (for DN 125-200 NORI 40)

▪ Process engineering ▪ Position indicator (standard for DN 250-350)

▪ Chemical industry ▪ Studs and nuts of A4-70 (low-temperature steel)

▪ Petrochemical industry ▪ Cap

▪ Sugar industry ▪ Oil and grease-free (wetted parts)

▪ Heat recovery systems ▪ Other flange designs or butt weld end designs

▪ Boiler recirculation ▪ Inspections to technical codes such as TRD/TRB/AD2000 –

German Steam Boiler / Pressure Vessel Regulations – or to
▪ Boiler feed applications customer specification

Fluids handled Body materials

▪ Water Overview of available materials
▪ Steam Material Material number Temperature limit
▪ Thermal oil P 250 GH 1.0460 Up to 450 ℃
▪ Other non-aggressive fluids such as gas or oil on request. GP 240 GH+N 1.0619+N Up to 450 ℃

Operating data Product benefits

Operating properties ▪ Reliable sealing: bonnet gasket fully confined to prevent
creep.
Characteristic Value
▪ Improved energy efficiency of the system. Short, easy-to-
Nominal pressure PN 25/40
insulate bonnet minimises heat losses.
Nominal size DN 10 - 3501)
▪ Additional stem seal for emergency operation and blow-
Max. permissible pressure 40 bar
out protection by standard back seat as well as back-up
Min. permissible temperature -10 °C gland packing made of pure graphite.
Max. permissible temperature +450 °C
▪ Hard-faced valve seat made of wear-resistant and
Selection as per pressure/temperature ratings (⇨ Page 4) corrosion-proof materials for long service life and high
functional reliability.

1) DN 250-350 Type BOA-HV/HEV

BOA-H/HE/HV/HEV 3
 Globe Valves
Bellows-type globe valves to DIN/EN

▪ Corrosion-resistant and easy to repair due to olive- 2. Nominal pressure

chromated nuts and bolts/screws.
3. Nominal size
4. Operating pressure
Related documents 5. Differential pressure
▪ We recommend using our maintenance-free DN 10-200 6. Operating temperature
NORI 40 globe valves, types ZXLB and ZXSB, if actuators
7. Fluid handled
are to be mounted (see type series booklet 7165.1).
8. Pipe connection
▪ Operating manual 0570.82
9. Variants
10. Number of type series booklet
On all enquiries/orders please specify
1. Type

Pressure/temperature ratings
Permissible operating pressures in bar at temperatures in °C (to EN 1092-1)2)
Nominal pressure Material RT3) 100 150 200 250 300 350 400 450
PN
25 P 250 GH - 1.0460 25,0 23,2 22,0 20,8 19,0 17,2 16,0 14,8 8,2
40 GP 240 GH+N - 40,0 37,1 35,2 33,3 30,4 27,6 25,7 23,8 13,1
40 DN 250-3504) 1.0619+N 27,0 27,0 23,0 22,0 21,0 19,0 18,0 17,0 13,0

2) Operating pressures to DIN 2401 are also permissible

3) RT: room temperature (-10 °C to +50 °C)
4) Values deviating from EN 1092-1

4 BOA-H/HE/HV/HEV
 Globe Valves
Bellows-type globe valves to DIN/EN

Materials
BOA-H BOA-HE

DN 10-505) DN 10-50

BOA-H BOA-HE

DN 65-200 DN 65-200

BOA-HV BOA-HEV
961
961
544 544
200 200
461 461 166
166 513
513
920 411
920 411 902
902 350
442
442 350 100 131
100

DN 250-350 DN 250-350

Overview of available materials

Part No. Description Material Material number Note
100 Body P 250 GH 1.0460 Hard-faced with stainless
GP 240 GH+N 1.0619+N BOA-H ≥ DN 50, BOA- steel (1.4370)
HE ≥ DN 65
131 Connection branch P 235 GH 1.0305 ≥ DN 65
166 Yoke P 250 GH 1.0460 DN 250

5) DN 10 to 40 with forged body

BOA-H/HE/HV/HEV 5
 Globe Valves
Bellows-type globe valves to DIN/EN

Part No. Description Material Material number Note

P 265 GH 1.0425 ≥ DN 300
172 Bonnet P 250 GH 1.0460
2006) Stem X 20 Cr 13 1.4021 Nitrided (DN 10-100)
3506) Valve disc X 20 Cr 13 1.4021
P 250 GH 1.0460 ≥ DN 125 Hard-faced (1.4115)
4426) Bellows X 6 CrNiMoTi 17-12-2 1.4571
5446) Threaded bush 11 SMn 30+C 1.0715 Nitrided
X 39 CrMo 17-1 1.4122 Nitrided, ≥ DN 250
4116) Joint ring CrNi steel/graphite
4616) Gland packing Graphite
513 Insert ring P 250 GH 1.0460 ≥ DN 250
902 Stud 21 CrMoV 5-7 1.7709 Olive-chromated
920 Hexagon nut 25 CrMo 4 1.7218
961 Handwheel JL1030 0.6020

Variants

BOA-H/HE

D N 1 0 -5 0 D N 6 5 -2 0 0

DN 10-200
Throttling plug Position indicator

BOA-HV/HEV

Balanced plug Throttling plug

6) Recommended spare parts

6 BOA-H/HE/HV/HEV
 Globe Valves
Bellows-type globe valves to DIN/EN

Dimensions

BOA-H dimensions

Dimensions in mm
PN DN l øD øk No. of bolt Bolt hole ø d4 x f b h17) h48) Travel ø d [kg]
holes dia. i
z
25/40 10 130 90 60 4 14 40 x 2 16 140 210 4,0 125 3.8
15 130 95 65 4 14 45 x 2 16 140 210 4,0 125 3.3
20 150 105 75 4 14 58 x 2 18 165 260 6,5 125 4.8
25 160 115 85 4 14 68 x 2 18 165 260 6,5 125 5.4
32 180 140 100 4 18 78 x 2 18 190 290 8,0 160 9.1
40 200 150 110 4 18 88 x 3 18 200 300 10,0 160 10.2
50 230 165 125 4 18 102 x 3 20 220 330 12,5 160 13.2
65 290 185 145 8 18 122 x 3 22 270 420 16,5 200 19.8
80 310 200 160 8 18 138 x 3 24 305 480 20,0 200 27
100 350 235 190 8 22 162 x 3 24 345 550 25,0 250 41.7
125 400 270 220 8 26 188 x 3 26 395 580 31,5 315 66
150 480 300 250 8 26 218 x 3 28 430 620 37,5 315 88
25 200 600 360 310 12 26 278 x 3 30 500 760 47,5 400 144.6
40 200 600 375 320 12 30 285 x 3 34 500 760 47,5 400 175

Mating dimensions - Standards Other flange designs

▪ E.g. groove (type D), tongue (type C), recess (type F),
Face-to-face lengths: EN 558-1/1, ISO 5752/1
spigot (type E) to EN 1092-1 at both ends
Flanges: Mating dimensions to DIN EN 1092,
ISO 7005 ▪ Other flange designs on request
Flange facing: DIN EN 1092-2, type B

7) Open
8) Vertical clearance for removal

BOA-H/HE/HV/HEV 7
 Globe Valves
Bellows-type globe valves to DIN/EN

BOA-HE dimensions

1)

2)

1) Socket weld end 2) Butt weld end

Dimensions in mm
PN DN l Butt weld ends, Butt weld ends to Socket weld ends to h19) h410) Travel ø d [kg]
unmachined DIN EN 12627 DIN EN 12760
ø Amax. øB min ø d2 ø d3 Associated ø D-0,5 ø C+0.2 bmin.
pipe
dimensions
25/40 10 130 37 10 18 13 17,2 x 2,0 25 17,6 10 165 260 4,0 125 3
15 130 37 15 22 17 21,3 x 2,0 30,5 21,7 10 165 260 4,0 125 2.9
20 130 37 20 28 22 26,9 x 2,3 36,5 27,1 13 165 260 6,5 125 3.3
25 130 37 24 34 28,5 33,7 x 2,6 44,5 33,8 13 165 260 6,5 125 3.2
32 160 60 33 43 37 42,4 x 2,6 53,5 42,5 13 200 290 8,0 160 5.5
40 180 60 38 49 43 48,3 x 2,6 60,5 48,7 13 200 300 10,0 160 5.5
50 210 73 48 61 54 60,3 x 3,2 73,5 61,1 16 220 330 12,5 160 8.3
65 290 76,1 64,9 76,1 69 76,1 x 3,6 270 420 16,5 200 17
80 310 88,9 79,9 88,9 81 88,9 x 4,0 305 480 20,0 200 30
100 350 114,3 100,1 114,3 104 114,3 x 5,0 345 550 25,0 250 40
125 400 139,7 125,5 139,7 130,5 139,7 x 4,5 395 580 31,5 315 60
150 480 168,3 148,3 168,3 156,5 168,3 x 5,6 430 620 37,5 315 80
200 600 219,1 199,1 219,1 204,5 219,1 x 7,1 500 760 47,5 400 130

Mating dimensions - Standards Different designs of butt weld ends, socket weld ends and
welding groove types are possible, but only within the
Face-to-face lengths: EN 12982/64 dimensions Amax. and Bmin..
Butt weld ends: DIN EN 12627 Fig. 2
Butt weld ends to DIN 3239, type 1, or socket weld ends to
Socket weld ends: DIN EN 12760 ASME B16.11/DIN 3239/2 possible.

9) Open
10) Vertical clearance for removal

8 BOA-H/HE/HV/HEV
 Globe Valves
Bellows-type globe valves to DIN/EN

BOA-HV dimensions

Dimensions in mm
PN DN l øD øk No. of bolt Bolt hole ø d4 x f b h111) h412) ød [kg]
holes dia. i
z
25 250 730 425 370 12 30 335 x 3 32 705 1035 500 270
300 850 485 430 16 30 395 x 4 34 785 1145 630 385
350 980 555 490 16 33 450 x 4 38 950 1400 800 630
40 250 730 450 385 12 33 345 x 3 38 705 1035 500 300
300 850 515 450 16 33 410 x 4 42 785 1145 630 430
350 980 580 510 16 36 465 x 4 46 950 1400 800 660

Mating dimensions - Standards Other flange designs

▪ E.g. groove (type D), tongue (type C), recess (type F),
Face-to-face lengths: EN 558-1/1, ISO 5752/1
spigot (type E) to EN 1092-1 at both ends
Flanges: Mating dimensions to DIN EN 1092,
ISO 7005 ▪ Other flange designs on request
Flange facing: DIN EN 1092-2, type B

11) Open
12) Vertical clearance for removal

BOA-H/HE/HV/HEV 9
 Globe Valves
Bellows-type globe valves to DIN/EN

BOA-HEV dimensions

1)

1) Butt weld end

Dimensions in mm
PN DN l Butt weld ends, Butt weld ends to h113) h414) ød [kg]
unmachined DIN EN 12627
ø Amax. øBmin. ø d2 ø d3 Associated
pipe dimensions
25/40 250 730 273 251 273 256,5 273,0 x 8,0 705 1035 500 260
300 950 345 305 323,9 306,5 323,9 x 8,8 785 1145 630 290
350 1100 385 335 355,6 336,5 355,6 x 10,0 950 1400 800 600

Mating dimensions - Standards Different designs of butt weld ends, socket weld ends and
welding groove types are possible, but only within the
Face-to-face lengths: EN 12982/64 (for DN 250) dimensions Amax. and Bmin..
or as per table (for DN 300, 350)
Butt weld ends: DIN EN 12627 Fig. 2

13) Open
14) Vertical clearance for removal

10 BOA-H/HE/HV/HEV
 Globe Valves
Bellows-type globe valves to DIN/EN

Dimensions of lead-sealable cap

Lead-sealable cap (prevents unauthorised closing)

Dimensions in mm
Nominal size d3 d4 h3 [kg]
DN
BOA-H BOA-HE
10 165 130 185 205 0,8
15 165 130 185 205 0,8
20 165 130 205 205 0,8
25 165 130 205 205 0,8
32 205 170 265 275 1,6
40 205 170 275 275 1,6
50 205 170 295 295 1,6
65 256 220 385 385 2,5
80 256 220 415 415 2,5
100 390 340 455 455 6,5
125 390 340 495 495 6,5
150 390 340 520 520 6,5
200 470 420 550 550 9,0

Installation instructions If a balanced plug design is required for DN 125 to 200, a

NORI 40 ZXLBV/ZXSBV or ZXLB/ZXSB shut-off valve must be
Shut-off globe valves must be installed in the line so as to used.
ensure that the fluid enters the valve beneath the valve disc
and flows out above the valve disc. They can also be installed Differential pressures in bar (standard valve disc)
in lines with alternating flow. DN 125 150 200 250 300 350
If the max. permissible differential pressures for shut-off are Δp [bar] 33 21 14 9 6 4,5
exceeded for valves from DN 125 to 350, a balanced plug
design is required. In this case the valve must be installed in For globe valves with throttling plug, detailed information
such a way that the pressure to be sealed off lies above the about the operating mode is required for optimum valve
valve disc. selection.

The balanced plug works on the bypass principle and can only
serve its purpose if backpressure builds up after opening, so
that the max. permissible differential pressures for shut-off
(see table) are not exceeded.

BOA-H/HE/HV/HEV 11
 04.07.2016
7161.1/23-EN

KSB Aktiengesellschaft
Bahnhofplatz 1 • 91257 Pegnitz (Deutschland)
Tel. +49 9241 71-0 • Fax +49 9241 71-1795
E-Mail: valves@ksb.com • www.ksb.de