Pickled and Oiled Steel Coils

Pickled and Oiled
Steel Coils
Product Manual
CHINA STEEL SUMIKIN VIETNAM JOINT STOCK COMPANY

Contents
Page
1.Introduction----------------------------------------------------------- 2
2. Features of P/O Steel Coils ------------------------------------- 3
3.Manufacturing Process ------------------------------------------- 4
4.Specifications ------------------------------------------------------- 6
4.1 Chemical Composition and Mechanical Properties-- 6
4.2 Tolerances --------------------------------------------- 16
4.3 Classification of Quality ------------------------------------- 25
5. Product Availability ------------------------------------------------ 26
6. Marking and Packing --------------------------------------------- 27
7. Surface Quality Control ------------------------------------------ 28
8. Comparison Of Specifications ---------------------------------- 29
9. Application ---------------------------------------------------------- 30
10. Ordering Information ------------------------------------------- 31
11. Unit Conversion Tables ----------------------------------------- 32
12. Notification -------------------------------------------------------- 33
China Steel Sumikin Vietnam Joint Stock Company, a delicate

steel-manufacturing company, we commit to continually improve our Quality
Management System and provide good products, and will endeavor to pursue
both internal and external satisfactions.
-1-
1. Introduction
China Steel Sumikin Vietnam Joint Stock Company (abbreviated as CSVC) is
a joint stock company of Taiwanese and Japanese companies. The main
investors are China Steel Corporation (Taiwan, R.O. China) and Nippon Steel &
Sumitomo Metal Corporation (Japan). CSVC started its construction in
September 2011, and start commercial running in November 2013.
CSVC can provide P/O, Cold Rolled, ASCR, Galvanized (GI & GA), and
Electrical Steel product with high quality. The total annual production capacity is
1.2 million metric tons.
CSVC implemented its quality management system based on ISO 9001

requirement, we especially stress on meeting customer requirement and
continually improving products quality. That’s why it makes CSVC to be a
reliable and trustworthy supplier of steel products. Besides, in order to commit
our responsibility to the environment, CSVC also put much effort in reducing or
even eliminating of any hazardous substance to make our products eco-friendly.
CSVC achieves many certificates such as: ISO 9001, ISO 17025, SNI Mark,
SIRIM Mark…
ISO 9001 ISO 17025
SNI Mark SIRIM Mark
-2-
-2-
2. Features of P/O Steel Coils
Pickled and oiled steel sheets are widely used in modern society, such as
automobile parts, wheels, brackets, rack, sheathing and so on. To meet the
multiple requirements, the specification of P/O coil became more and more
diversified. Customers shall always need to choose appropriate specification
based on end usage. Brief introductions of products are as below.
JIS G3131 SPHC/D/E/F, JFS A1001 JSH270C/D/E

JIS/JFS standard of P/O products, grade from commercial quality to deep drawing
quality, which can be used in various applications, mainly focus on their deforming
properties.
JIS G3101 SS330~540, ASTM A1011/1018 SS Grade 30-80
P/O steel coils used for general structure with minimum tensile strength from 330
to 620 N/mm2, which are widely used in various structures or other
strength-required parts.
JIS G3113 SAPH310/370/400/440
JIS SAPH 310~440 products are specially designed for automobile structural use,
tensile strength from 310 to 440 N/mm2, which can be used in automobile
structural applications.
ASTM A1011/1018 HSLA
High strength low-alloy P/O steel coils mainly applicable to structural use such as
sections and stiffening plates.
JIS G3134 SPFH490/540(Y)/590(Y), JSH540Y~590Y
P/O steel coils with high strength, excellent stretchability, which are widely used in
automobile structural reinforce members to reduce vehicle.
EN10149-2 S315MC~S500MC
P/O steel coils with high yield strength from the range 315 to 500 N/mm2, mainly
applicable to cold forming used and yield strength-required parts.
-3-
3. Manufacturing Process
Pickled and oiled steel coils are produced from hot-rolled coil, the typical
manufacturing processes are described as Fig.1
Hot Roll coil Pickling and oiling P/O coil

Fig.1: Manufacturing process flow of P/O products
CSVC produce its P/O products by the picking line, which is a part of PLTCM
(abbreviated from Picking and Tandem cold-rolling Mill).
Some pictures of Pickled and Oiled line
Picture 1: Two Pay-Off Reel In The

Entry Section
Picture 2: Laser Beam Welder
-4-
Picture 3: Polypropylene Pickling
Tank
Picture 4: Electrostatic Oiler

Located In The Delivery Section
Picture 5: Tension Reel
-5-
4. Specifications
While much effort has been made to ensure the accuracy of the information contained
within this publication, the use of the information is at the user’s risk and no warranty is
implied or expressed by CSVC with respect to the use of information contained herein. The
information in this publication is subject to change without notice. Please contact CSVC
office for the latest information.
4.1 Chemical Compositions and Mechanical Properties

4.1.1 JIS G3131 Hot-Rolled Mild Steel Plate, Sheets and Strip
Tensile Test Bendability

Chemical Composition %
Elongation % Inside radius
Grade Tensile
Test Thickness (t) Test
Thickness (t) mm Angle of
Strength
peice mm peice
2 Bending
C Mn P S N/mm
t 1.6≦t 2.0≦t 2.5≦t 3.2≦t
t≧4.0 t＜3.2 t≧3.2
＜1.6 ＜2.0 ＜2.5 ＜3.2 ＜4.0
Flat
0.12 0.60 0.045 0.035 27 29 29 29 31 31
SPHC on 0.5 t
max. max. max. max. min. min. min. min. min. min.
itself
0.10 0.45 0.035 0.035 30 32 33 35 37 39 No.5, in No.3, in

SPHD ─ ─
max. max. max. max. min. min. min. min. min. min. rolling rolling
270 0
180 directi-
min. directi-
0.08 0.40 0.030 0.030 31 33 35 37 39 41
SPHE on ─ ─ on
0.08 0.35 0.025 0.025 37 38 39 39 40 42

SPHF ─ ─
Remark:
1) Grade SPHF is manufactured by a special process, such as made of killed steel to improve
draw ability.
2) The values specified shall not apply to the irregular portions at both ends of steel strip.
3) The bend test may be omitted by the manufacturer’s decision, but the bendability shall
satisfy the specification. However, when the purchaser designates, the test shall be
performed.
-6-
4.1.2 JIS G3101 Rolled Steel for General Structure
Chemical Composition
%
Elongation % Inside radius
No.5 No.1A
Grade Yield Tensile
Test Test Angle of
C Mn P S Strength Strength Test
Piece Piece Bending
2 2
N/mm N/mm Thickness(t) Piece
Thickness(t)
t≦5 5＜t
330 - 26 21
SS330 205 min 0.5 t
430 min min
0.050 0.050 400 - 21 17
SS400 ─ ─ 245 min 1.5 t
max. max. 510 min min
0
490 - 19 15 180
SS490 285 min 2.0 t
610 min min
0.30 1.60 0.040 0.040 No.1
16 13
SS540 400 min 540 min 2.0 t
max. max. max. max. min min
Remark:
1) Alloy elements other than those shown in the above table may be added if necessary.
performed.
4.1.3 JIS G3113 Hot-Rolled Steel Plates, Sheets and Strip for Automobile
Structural Uses
Yield Point
2
Elongation % (rolling direction) Inside radius
N/mm
Test
Thickness (t) Thickness (t) mm piece
Tensile Thickness (t) mm
Grade mm Test Angle of
Strength
2 piece Bending
N/mm
t＜ 3.15 t≧
6.0≦t 1.6＜ 2.0＜ 2.5＜ 4.0＜
＜ t≧6.3 t＜2.0
6.0 ＜8.0 t≦2.0 t≦2.5 t≦3.15 t≦6.3 2.0
t≦4.0
No.3 test
No.5 test piece in
310 (185) (185) 33 34 36 38 40 41 piece in 0
Flat on 1.0 t transverse
SAPH310 180
min. min. min. min. min. min. min. min. min. rolling itself rolling
direction direction
-7-
370 225 225 32 33 35 36 37 38
SAPH370 0.5 t 1.0 t
min. min. min. min. min. min. min. min. min.
400 255 235 31 32 34 35 36 37

SAPH400 1.0 t 1.0 t
440 305 295 29 30 32 33 34 35

SAPH440 1.0 t 1.0 t
Remark:
1) Values in parentheses mean reference values.
performed.
4.1.4 JIS G3132 Hot-Rolled Carbon Steel Strip for Pipes and Tubes
Elongation % Test Inside radius
peice
Tensile Angle Thickness (t)
Thickness (t)mm Test
Grade Strengt of
mm peice
C Si Mn P S h Bendin
2
N/mm g
1.6≦t 3.0≦t
t＜1.6 t≧6.0
＜3.0 ＜6.0
Flat
0.10 0.35 0.50 270 30 32 35 37
SPHT1 on 0.5 t
max. max. max. min. min. min. min. min.
itself
0.18 0.60 340 25 27 30 32 No.5 No.3
SPHT2 1.0 t 1.5 t
max. max. 0.04 0.04 min. min. min. min. min. in in
0
0.30 0 0 rolling 180 rolling
0.25 410 (20 22 25 27
SPHT3 0.35 ︱ max. max. directio 1.5 t 2.0 t directio
max. min. min). min. min. min.
max. 0.90 n n
0.30
0.30 490 30 32 35 37
SPHT4 ︱ 1.5 t 2.0 t
max. min. min. min. min. min.
1.00
Remark：
1) The Si content of SPHT1 can be modified to 0.04% max. upon agreement.
performed.
-8-
4.1.5 JIS G3134 Hot-Rolled High Strength Steel Sheets with Improved Formability
for Automobile Structural Uses
Elongation %
Yield
Inside radius
Tensile Point or
Grade Thickness(t) mm Test peice Angle of Thickness(t) Test peice
Strength Proof
2
Bending mm
N/mm Stress
2 1.6≦t 2.0≦t 2.5≦t 1.6≦t＜
N/mm 3.25≦t 3.25≦t
＜2.0 ＜2.5 ＜3.25 3.25
SPFH
490min. 325min. 22min. 23min. 24min. 25min. 0.5 t 1.0 t
490
SPFH No.5
540min. 355min. 21min. 22min. 23min. 24min. 1.0 t 1.5 t No.3
540 transverse transverse
SPFH 0
590min. 420min. 19min. 20min. 21min. 22min. to 180 1.5 t 1.5 t to
590
rolling rolling
SPFH
540min. 295min. ─ 24min. 25min. 26min. 1.0 t 1.5 t direction
540Y direction
SPFH
590min. 325min. ─ 22min. 23min. 24min. 1.5 t 1.5 t
590Y
Remark:
1) The chemical composition shall be agreed upon by the purchaser and supplier, if necessary.
performed.
4.1.6 JIS G4051 Carbon Steels for Machine Structural Use

Chemical Composition ％
Grade C Si Mn P S
S10C 0.08─0.13 0.30─0.60
S12C 0.10─0.15 0.30─0.60
S15C 0.13─0.18 0.30─0.60
S17C 0.15─0.20 0.30─0.60
S20C 0.18─0.23 0.15~0.35 0.30─0.60 0.030max. 0.035max.
S22C 0.20─0.25 0.30─0.60
S25C 0.22─0.28 0.30─0.60
S28C 0.25─0.31 0.60─0.90
S30C 0.27─0.33 0.60─0.90
-9-
S33C 0.30─0.36 0.60─0.90
S35C 0.32─0.38 0.60─0.90
S38C 0.35─0.41 0.60─0.90
S40C 0.37─0.43 0.60─0.90
S45C 0.42─0.48 0.60─0.90
S48C 0.45─0.51 0.60─0.90
S50C 0.47─0.53 0.60─0.90
4.1.7 JFS A1001 Hot Rolled Steel Sheet and Strip for Automobile Use
(1) Mild steel, commercial steel, high yield ratio type and low yield ratio type steel.

Designation Yield strength N/mm
2
Elongation Inside radius
Tensile
Test Angle of Test
strength 2.5 ≦t＜
2 t＜2.5 6.3 ≦t t≦6.5 Piece Bending 2.6≦t≦3.2 3.2＜t Piece
N/mm 6.3
Flat on
JSH270C 270min. 185~325 175~305 165~285 35~52 0.5t
itself
JIS No 3
Flat on
JSH270D 270min. 175~305 165~285 155~265 37~55 0.5t Rolling
itself
JIS No 5 direction
Flat on
JSH270E 270min. 155~275 145~255 - 40~56 Rolling 0.5t
itself
direction
JSH370W 370min. 215~355 205~335 195~315 33~50 1.0t 1.0t
JSH400W 400min. 235~375 225~355 215~335 31~49 1.0t 1.0t
JSH440W 440min. 275~410 265~390 255~370 28~47 0 1.0t 1.0t
180
JIS No 5 JIS No 3
JSH490W 490min. 325~460 315~450 305~430 25~41 Perpendi- 1.0t 1.0t Perpendi-
cular to cular to
JSH540W 540min. 365~510 355~500 345~480 22~38 Rolling 1.0t 1.5t Rolling
direction direction
JSH440R 440min. 325~450 315~440 305~420 26~41 1.0t 1.0t
IS No 5
JSH590R 590min. 470~630 450~620 450~610 17~33 Rolling 1.5t 1.5t
direction
JSH590Y 590min. 325~500 325~490 - 22~39 1.5t 1.5t
Remark：The bend test may be omitted by the manufacturer’s decision, but the bendability shall
performed.
4.1.8 ASTM A1011 Carbon, structural, High-Strength Low-Alloy Steel and

High-Strength Low-Alloy with Improved Formability.
a. Chemical composition
- 10 -
Grade
C Mn P S Al Cu Ni Cr Mo V Nb Ti
CS Type
0.10max.
A
0.030max.
CS Type
0.02/0.15 0.60max.
B 0.025max.
0.035max. ─
CS Type
0.08max. 0.10max.
C
(1)
0.15max
CS Type
0.10max. 0.70max. 0.030max. 0.008max.
D
DS Type
0.08max.
A
0.50max. 0.020max. 0.030max. 0.01min. 0.025max.
DS Type
0.02/0.08
B
SS Gr. 30
SS Gr. 33 0.90max.
SS Gr.36
0.20max. 0.20max. 0.06max. 0.008max. 0.008max.
Type 1
SS Gr. 36
1.35max.
Type 2
SS Gr. 40 0.90max.
0.25max. 0.035max. 0.04max. ─ 0.15max. 0.025max.
SS Gr. 45
Type 1
SS Gr. 50
1.35max.
SS Gr. 55
SS Gr. 60
SS Gr. 70
- 11 -
HSLAS
Gr.45
0.22max.
C1ass 1
HSLAS
Gr.45
0.15max.
C1ass 2
HSLAS
Gr.50
0.23max.
C1ass 1
HSLAS 1.35max.
Gr.50
0.15max.
C1ass 2
HSLAS
Gr.55
0.25max.
C1ass 1
HSLAS
Gr.55
0.15max.
C1ass 2
HSLAS 0.04max.
Gr.60
0.26max.
C1ass 1
HSLAS
Gr.60
0.15max.
C1ass 2
HSLAS 1.50max. 0.005min. 0.005min. 0.005min.
Gr.65
0.26max.
C1ass 1
HSLAS
Gr.65
0.15max.
C1ass 2
HSLAS
Gr.70
0.26max.
C1ass 1
HSLAS 0.16max.
Gr.70
0.15max.
C1ass 2
HSLAS-F
Gr.50 1.65max.
0.16max.
HSLAS-F
0.15max. 0.020max. 0.025max.
Gr.60
HSLAS-F
0.16max.
Gr.70
Remark：1) Cr is 0.25% maximum when C≦0.05%. Ti is permitted, to the less of 3.4N+1.5S or
0.025% maximum, when C≧0.02%.
2) Nb, Ti and V is 0.005% min. when specified.
b. Mechanical properties
Yield
Grade Tensile Strength Elongation ﹪ G.L.=2 inch （Inside Radius）
Test Test
Strength Mpa
Piece Piece
MPa 2.5mm<t
t<6.0mm t<1.6mm 1.6mm≦t<2.5mm t=2.5mm t<6.0mm
<6.0mm
CS Type A ─ 205/340 25min. 25min. 25min. 25min. ─ Transverse

in
CS Type B ─ 205/340 25min. 25min. 25min. 25min. ─ to
rolling
CS Type C ─ 205/340 25min. 25min. 25min. 25min. ─ rolling
direction
CS Type D ─ 205/340 25min. 25min. 25min. 25min. ─ direction
- 12 -
DS Type A ─ 205/310 28min. 28min. 28min. 28min. ─
DS Type B ─ 205/310 28min. 28min. 28min. 28min. ─
SS Gr. 30 340min. 205min. 21min. 24min. 25min. 25min. 1.0t
SS Gr. 36
365min. 250min. 17min. 21min. 22min. 22min. 1.5t
Type1
SS Gr. 36
400/550 250min. 16min. 20min. 21min. 21min. 2.0t
Type2

HSLAS
Gr.45
C1ass 1 410min. 310min. 23min. 23min. 23min. 25min. 1.5t
HSLAS
Gr.45
HSLAS
Gr.50
HSLAS
Gr.50
HSLAS
Gr.55
HSLAS
Gr.55
HSLAS
Gr.60
HSLAS
Gr.60
HSLAS
Gr.65
HSLAS
Gr.65
HSLAS
Gr.70
HSLAS
Gr.70
HSLAS-F
Gr.50
- 13 -
HSLAS-F
480min. 410min. 20min. 20min. 20min. 22min. 1.5
Gr.60
HSLAS-F
Gr.70
4.1.9 EN 10149-2 Hot-rolled flat products made of high yield strength steels for
cold forming
a. Chemical composition
Steel
Grade Al
No. C Mn Si P S Nb V Ti Mo B
total
1.30
S315MC 1.0972
max. 0.020
1.50 max.
S355MC 1.0976
max.
1.60
S420MC 1.0980 0.015 0.09 0.20 0.15 －－
0.12 max. 0.50 0.25
max. 1.60 max. max. min. max. max. max.
S460MC 1.0982 0.015
max.
1.70 max.
S500MC 1.0984
max.
1.80
S550MC 1.0986
max.
Remark :
1) Nb＋V＋Ti≦0.22
2) If agreed at the time of enquiry and order, the sulfur content shall be 0.010% max.
b. Mechanical properties
Elongation% Bend Test

（Inside
Tensile thickness(t) mm
Yield Strength diameter）
Grade Steel No. 2 Strength
N/mm
N/mm
2 3≦t 180˚
t＜3
(in transverse
G.L.=80mm G.L.= 5.65 S 0
rolling direction
S315MC 1.0972 315min. 390-510 20min. 24min. Flat on itself
S355MC 1.0976 355min. 430-550 19min. 23min. 0.5t
S420MC 1.0980 420min. 480-620 16min. 19min. 0.5t
S460MC 1.0982 460min. 520-670 14min. 17min. 1.0t
S500MC 1.0984 500min. 550-700 12min. 14min. 1.0t
S550MC 1.0986 550min. 600-760 12min. 14min. 1.5t
Remark：”S0” Test piece section area.
- 14 -
4.1.10 SAE J403 Carbon Steel
Grade
C Si Mn P S
(1)
1005 0.06max. 0.35max.
(1) (2)
1006 0.08max. 0.25~0.40
(1) (2)
1008 0.10max. 0.30~0.50
1010 0.08~0.13 0.30~0.60
1012 0.10~0.15 0.30~0.60
1015 0.13~0.18 0.30~0.60
1016 0.13~0.18 0.60~0.90
1017 0.15~0.20 0.30~0.60
1018 0.15~0.20 0.60~0.90
1019 0.15~0.20 0.70~1.00
1020 0.18~0.23 0.30~0.60
1021 0.18~0.23 0.60~0.90
1022 0.18~0.23 --- 0.70~1.00 0.030max. 0.050max.
1023 0.20~0.25 0.30~0.60
1026 0.22~0.28 0.60~0.90
1030 0.28~0.34 0.60~0.90
1033 0.30~0.36 0.70~1.00
1035 0.32~0.38 0.60~0.90
1038 0.35~0.42 0.60~0.90
1040 0.37~0.44 0.60~0.90
1045 0.43~0.50 0.60~0.90
1049 0.46~0.53 0.60~0.90
1050 0.48~0.55 0.60~0.90
1055 0.50~0.60 0.60~0.90
1060 0.55~0.65 0.60~0.90
Remark:
1) Ultra low carbon, interstitial free stabilized and non-stabilized steel may be supplied for
these grades.
2) MANGANESE{For grades G10060 applicable to Structural Shapes, Plates, Strip, Sheets
and Welded Tubing, the manganese limit is 0.45% maximum and 0.50% maximum,
respectively, with no minimum.
- 15 -
4.2 Tolerances
4.2.1 Thickness Tolerances
(1) JIS G3113 Thickness Tolerances
Unit：mm
Width(w)
w＜1200 1200≦w＜1500 1500≦w≦1600
Thickness(t)
1.60≦t＜2.00 ±0.16 ±0.17 ±0.18
2.00≦t＜2.50 ±0.17 ±0.19 ±0.21
2.50≦t＜3.15 ±0.19 ±0.21 ±0.24
3.15≦t＜4.00 ±0.21 ±0.23 ±0.26
4.00≦t＜5.00 ±0.24 ±0.26 ±0.28
5.00≦t＜6.00 ±0.26 ±0.28 ±0.29
t=6.00 ±0.29 ±0.30 ±0.31
Remark:
1) The positions where the thickness is to be measured shall be as follows:
(A) For mill-edged products, any point 25mm and over inward from the edge.
(B) For cut-edged products, any point 15mm and over inward from the edge.
2) The values specified shall not apply to the irregular portions at both ends of steel coils.

Unit：mm
Width(w)
w＜1200 1200≦w＜1500 1500≦w≦1600
Thickness (t)
t＜1.60 ±0.14 ±0.15 ±0.16a
1.60≦t＜2.00 ±0.16 ±0.17 ±0.18
2.00≦t＜2.50 ±0.17 ±0.19 ±0.21
2.50≦t＜3.15 ±0.19 ±0.21 ±0.24
3.15≦t＜4.00 ±0.21 ±0.23 ±0.26
4.00≦t＜5.00 ±0.24 ±0.26 ±0.28
- 16 -
Width(w)
w＜1200 1200≦w＜1500 1500≦w≦1600
Thickness (t)
5.00≦t＜6.00 ±0.26 ±0.28 ±0.29
t=6.00 ±0.29 ±0.30 ±0.31
Remark:
1) The above table applies to SPHC, SPHD, SPHE and SPHF grades.
2) Thickness shall be measured at any point of 20mm and over inside the edges.
4) The value shall be applied to the steel strip under 1600mm in width.

unit：mm
Width(w)
w＜1200 1200≦w＜1500 1500≦w≦1600
Thickness (t)
t＜1.60 (±0.14) ±0.15 ±0.16
1.60≦t＜2.00 ±0.16 ±0.17 ±0.18
2.00≦t＜2.50 ±0.17 ±0.19 ±0.21
2.50≦t＜3.15 ±0.19 ±0.21 ±0.24
3.15≦t＜4.00 ±0.21 ±0.23 ±0.26
4.00≦t＜5.00 ±0.24 ±0.26 ±0.28
5.00≦t＜6.00 ±0.26 ±0.28 ±0.29
t=6.00 ±0.29 ±0.30 ±0.31
Remark:
1) The above table applies to SPHC, SPHD, SPHE and SPHF grades.
2) Thickness shall be measured at any point of 20mm and over inside the edges.
- 17 -
unit：mm
Width(w)
w＜1200 1200≦w＜1500 1500≦w≦1600
Thickness (t)
t＜1.60 (±0.14) ±0.15 ±0.16
1.60≦t＜2.00 ±0.16 ±0.19 ±0.20
2.00≦t＜2.50 ±0.18 ±0.22 ±0.23
2.50≦t＜3.15 ±0.20 ±0.24 ±0.26
3.15≦t＜4.00 ±0.23 ±0.26 ±0.28
4.00≦t＜5.00 ±0.26 ±0.29 ±0.31
5.00≦t＜6.00 ±0.29 ±0.31 ±0.32
t=6.00 ±0.32 ±0.33 ±0.34
Remark:
1) The above table applies to SPHT4 grades.
2) Thickness shall be measured at any point 20mm and over inside the edges.

Unit：mm
Width(w)
w＜1200 1200≦w＜1500 1500≦w≦1600
Thickness (t)
1.60≦t＜2.00 ±0.16 ±0.19 ±0.20a
2.00≦t＜2.50 ±0.18 ±0.22 ±0.23a
2.50≦t＜3.15 ±0.20 ±0.24 ±0.26a
3.15≦t＜4.00 ±0.23 ±0.26 ±0.28
4.00≦t＜5.00 ±0.26 ±0.29 ±0.31
5.00≦t＜6.00 ±0.29 ±0.31 ±0.32
t = 6.00 ±0.32 ±0.33 ±0.34
- 18 -
Remark:
1) The positions where the thickness is to be measured shall be as follows:
(A) For mill-edged products, any point 25mm and over inward from the edges.
(B) For cut-edged products, any point 15mm and over inward from the edges.
3) The values are applicable to the steel sheets and coils under 1600 mm in width.
6) JIS G3193 Thickness Tolerances

Unit：mm
Width(w)
w＜1600 W=1600
Thickness (t)
t＜1.25 ±0.16 ─
1.25≦t＜1.60 ±0.18 ─
1.60≦t＜2.00 ±0.19 ±0.23
2.00≦t＜2.50 ±0.20 ±0.25
2.50≦t＜3.15 ±0.22 ±0.29
3.15≦t＜4.00 ±0.24 ±0.34
4.00≦t＜5.00 ±0.45 ±0.55
5.00≦t＜6.00 ±0.50 ±0.60

Remark:
1) The above table applies to SS, SPA-H, and SXXC grades.
2) The positions where the thickness is to be measured shall be as follows：
(A) For mill-edged products, any point 25mm and over inward from the edges.
(B) For cut-edged products, any point 15mm and over inward from the edges.
3) Tolerance given in the table may be limited to either plus side or minus side upon the
agreement between the purchaser and the supplier.
The total tolerance range in this case shall be equal to that given in this table.
- 19 -
(7) JFS A1001 Thickness Tolerances (Class A)
unit：mm
Width (w)
Specified minimum
w<1200 1200≦w<1500 1500≦w≦1800
tensile strength
Thickness (t)
1.40≦t<1.60 ±0.14 ±0.15 ±0.16

1.60≦t<2.00 ±0.16 ±0.17 ±0.18
2.00≦t<2.50 ±0.17 ±0.19 ±0.21
TS ≤ 440 2.50≦t<3.15 ±0.19 ±0.21 ±0.24

N/mm2 3.15≦t<4.00 ±0.21 ±0.23 ±0.26
4.00≦t<5.00 ±0.24 ±0.26 ±0.28
5.00≦t<6.00 ±0.26 ±0.28 ±0.29
t=6.00 ±0.29 ±0.30 ±0.31
1.60≦t<2.00 ±0.16 ±0.19 ±0.20
2.00≦t<2.50 ±0.18 ±0.22 ±0.23
2.50≦t<3.15 ±0.20 ±0.24 ±0.26
TS＞440
3.15≦t<4.00 ±0.23 ±0.26 ±0.28
N/mm2
4.00≦t<5.00 ±0.26 ±0.29 ±0.31
5.00≦t<6.00 ±0.29 ±0.31 ±0.32
6.00≦t<8.00 ±0.32 ±0.33 ±0.34
Remark: Thickness shall be measure at any point not less than 25mm from a side edge in the
case if mill edge, and not less than 15mm from a side edge in the case of cut edge
(8) ASTM A568 Thickness Tolerances (Carbon Steel)

Unit：mm
Width(w)
850≦w＜1016 1016≦w＜1220 1220≦w＜1524 1524≦w≦1600
Thickness (t)
1.2≦t＜1.30 ±0.10 ±0.10 ─ ─
1.30≦t＜1.45 ±0.10 ±0.11 ±0.11 ±0.12
1.45≦t＜1.81 ±0.11 ±0.11 ±0.12 ±0.12
1.81≦t＜2.49 ±0.12 ±0.12 ±0.12 ±0.15
2.49≦t＜4.58 ±0.12 ±0.15 ±0.15 ±0.15
4.58≦t≦5.84 ±0.15 ±0.17 ±0.19 ±0.20
Remark:
1) The above table applies to ASTM A1011and A1018 specifications.
2) The values in the above table are converted from inch-pound units.
- 20 -
3) Thickness shall be measured at any point across the width not less than 9.5mm from a cut
edge and not less than 19mm from a mill edge.
(9) ASTM A568 Thickness Tolerances (High-Strength Low-Alloy Steel)

Unit：mm
Width(w)
1017≦w＜ 1220≦w＜
850≦w＜1017 1525≦w≦1600
1220 1525
Thickness(t)
1.2≦t＜1.30 ±0.11 ±0.11 ─ ─

1.30≦t＜1.50 ±0.11 ±0.12 ±0.12 ─
1.50≦t＜1.78 ±0.12 ±0.12 ±0.12 ±0.15
1.78≦t＜2.09 ±0.12 ±0.12 ±0.12 ±0.15
2.09≦t＜2.49 ±0.15 ±0.15 ±0.15 ±0.17
2.49≦t＜4.58 ±0.15 ±0.19 ±0.19 ±0.20
4.58≦t≦5.84 ±0.17 ±0.19 ±0.19 ±0.20
Remark:
3) Thickness shall be measured at any point across the width not less than 9.5mm from a cut
edge and not less than 19mm from a mill edge.
(10) ASTM A635 Thickness Tolerances

Unit：mm
Width(w)
850≦w＜1017 1017≦w＜1220 1220≦w＜1525 1525≦w≦1600
Thickness(t)
5.84≦t＜6.00 ±0.20 ±0.22 ±0.22 ±0.25
Remark:
3) Thickness shall be measured at any point across the width not less than 9.5mm from a cut edge
and not less than 19mm from a mill edge.
- 21 -
4.2.2 Width, Camber and Flatness Tolerances
(1) JIS G3193 Width Tolerances
unit：mm
Tolerances
Cut edge（by ordinary
Width (w) Thickness (t) Mill edge
cutting）
max. min. max. min.
850≦w＜1000 1.20≦t＜20.0 25 0 10 0
t＜6.00 10
1000≦w＜1250 30 0 0
6.00≦t 15
t＜6.00 10
1250≦w＜1600 35 0 0
6.00≦t 15
t＜6.00 10
w=1600 40 0 0
6.00≦t 20
(2) JIS G3193 Camber Tolerances

Unit：mm
Width (w) Maximum value
w≧850 5 in any 2000 length
(3) JIS G3193 Flatness Tolerances

Unit：mm
Width(w)
w＜1250 1250≦w＜1600 w =1600
Thickness (t)
t＜1.60 18max. 20max. ─
1.60≦t＜3.15 16max. 18max. 20max.
3.15≦t＜4.00 16max.
4.00≦t＜5.00 14max.
5.00≦t＜6.00 13max.
Remark: 1) The table is not applicable by the plate and sheet leveling done after leveling
machine.
2) Values in this table shall be applied to any 2000 mm length. For the steel plate
and sheet under 2000 mm in length, the values shall be applied to the full length.
For the steel plate and sheet over 2000 mm in wave pitch, the values in this
- 22 -
table shall be applied to any pitch of the wave. For those over 4000 mm in wave
pitch, however, the above values shall be applied to any 4000 mm length.
3) Unless otherwise specified, 1.5 times the maximum deviation from flatness
specified in this table shall be applied to the steel plate and sheet of which the
lower limit of yield point or proof strength in tensile test is at least 460N/mm2, or
chemical position on hardness is equivalent to.
4) The table does not apply to rolled edge (mill edge) steel plate.
(4) JFS A1001 Width Tolerances (Class A)

unit：mm
Tolerance
Width (w) Thickness (t) Mill edge Cut edge
max. min. max. min.
t＜6.0
850≦w＜1000 25 0 10 0
6.0≦t
1000≦w＜ t＜6.0 10
30 0 0
1250 6.0≦t 15
t＜6.0 10
1250≦w＜
35 0 0
1600 6.0≦t 15
t＜6.0 10
1600≦w 40 0 0
6.0≦t 15
(5) JFS A1001 Flatness Tolerances (Class B)

unit：mm
Width (w)
Specified minimum
w<1250 1250≦w<1600 1600≦w
tensile strength
Thickness (t)
1.20≦t<1.60 11 12 13
1.60≦t<3.15 10 11 12
TS ≤ 440 3.15≦t<4.00 10 10 10
4.00≦t<6.00 8 8 8
6.00≦t 8 8 8
1.60≦t<3.15 10 11 12
3.15≦t<4.00 10 11 12
440<TS<590
4.00≦t<6.00 8 10 11
6.00≦t 8 9 10
- 23 -
(6) JFS A1001 Camber Tolerances
Unit：mm
Width (w) Maximum value
All 5mm in any 2000mm length
(7) ASTM A568 Width Tolerances

Unit：mm
Tolerances
Mill edge
Width(w)
High strength low Cut Edge
Carbon Steel
alloy Steel
＋23 ＋28 ＋3.1
660≦w＜763
－0 －0 －0
＋28 ＋28 ＋4.7
763≦w＜890
－0 －0 －0
＋28 ＋31 ＋4.7
890≦w＜1220
－0 －0 －0
＋28 ＋31 ＋6.3
1220≦w＜1270
－0 －0 －0
＋38 ＋38 ＋6.3
1270≦w＜1525
－0 －0 －0
＋38 ＋41 ＋7.9
1525≦w＜1651
－0 －0 －0
Remark: 1) The above table applies to ASTM A1011 and A1018 specifications.
3) The above table does not apply to the uncropped ends of mill-edged coils.
- 24 -
(8) ASTM A635 Width Tolerances
Unit：mm
Tolerances
Width (w)
Mill Edge Cut Edge
＋3.1
720≦w＜763
＋28 －0
－0
763≦w＜890
＋4.7
－0
890≦w＜1220
＋31
－0
1220≦w＜1271
＋6.3
+38 －0
1271≦w＜1525
－0
＋41 ＋7.9
1525≦w=1600
－0 －0
Remark: 1) The above table applies to ASTM A659 and A1011, 11018 specifications.
3) The above table does not apply to the uncropped ends of mill-edged coils.
4.3 Classification of Quality

Common
Classification Property and purpose
specifications
Appropriate for normal forming, bending and welding,
Commercial JIS G3131 SPHC
such as water pipe, electric wire pipe, parts with
Quality(CQ) SAE 1008~1023 CQ
non-strength demand, cover, etc...
JIS G3131 SPHD
Drawing Appropriate for drawing work or forming, such as
JSH 270D 270E
Quality(DQ) bicycle bead, handle grip, 5-way pipe, etc...
SAE 1006~1008 DQ
Appropriate for simple bending work, welding and
SS400~SS490
Structure rivet
SM400~SM490
Quality(SQ) joint with strength demand, such as ship hull, bridge,
ASTM A36
scaffold, etc...
Appropriate for automobile parts, with strict inner
JIS G3113
Automobile quality
SAPH310~SAPH440
Structure and forming demand, normally used for automobile
JIS G3134
Quality (ASQ) wheel rim, suspension system, chassis beam, brake
SPFH490~SPFH590
back panel, etc…
- 25 -
Strength, low temperature toughness, welding,
Line Pipe JIS G3132
formability, inner quality is all strictly demanded. Mainly
Steel(LPS) SPHT1~ SPHT4
used for gasoline, gas vapor, liquid transportation.
SAE1006 Such steel is designed according to customer quality
Re-Rolling
(RRQ)~SAE1022 demand and process ability. It can be produced to cold
Quality(RRQ)
(RRQ) rolling steel, galvanizing steel, color steel.
5. Product Availability
5.1 Unit mass
Item Product Type Maximum Unit Mass

Pickled and Oiled, Mill Edge
Coil 20MT ／Coil
Pickled and Oiled, Cut Edge
5.2 Available Sizes

Unit：mm
HR Product Thickness Range Mill Edge/Cut Edge Inner Diameter
Pickled and
1.40~6.0 850~1600 610
Oiled Coil
Remark: The above data is reference only. Actual available sizes range shall be
confirmed with CSVC sales department.
- 26 -
6. Marking and Packing
6.1 Marking for pickled and oiled steel
(The label is a sample and just for reference)
6.2 Packing for pickled and oiled steel
Case1
Film/Paper wrapping + Paper edge
protector + Metal edge protector +
Hard board paper + Metal
protector + Circumferential
strapping + Eye strapping
Case 2
Film/Paper wrapping +Paper edge
Protector + Hard Board paper +
Circumferential strapping + Eye
Strapping
- 27 -
7. Surface Quality Control
The surface quality controls for hot rolled products when producing are based on the
requirements of downstream uses. Such controls are roughly classiﬁed as Un-Exposed
(UE), General Purposes (GP), and General Exposed (GE), as follows:
Hot rolled surface, quality and suitable application recommendation

GE
GP UE
Class (General
(General Purposes) (Unexposed)
Exposed)
Bicycle Parts, Bicycle Gear Hanger, Jack, Container
Elevator Panel, Square Pipe Angle Plate
Brake Compressor Case, Tubes For
Backing Plate, Motorcycle Structural Use
ERW Pipe Tube, Drawing Tube, Chain Plate
for Tubes for Black or
Electro-coating, Automobile Cushion, Hot-Dipped ERW
Ceiling Fan Parts, Automobile Pipe
Jack(electrostatic Parts, Automobile Rear Chain
coated), Axle, Retaining Wall
Automobile Drive Shaft, Boiler Parts Spiral Pipe
Backing Parts, Water Stop of Slurry Fence Parts
Oil Drum Nozzle Wall For LNG Tank Guardrail of
Motorcycle, Oil Drum, Oil Tank, Highway
Application
Sprocket(Cr- Gardening Dust Tube for
Coating), Wheel Tool, Gas Cylinder, Hand Thermal
Disk and Wheel Tool –SxxC, Cold Re- Power Plant
Rim Rolling, Warehouse, Non- Chain
(Electrical Expanded Welded Line Plate(Re-Rolling)
Galvanized or Pipe, Speaker Washer
Electrostatic Free Wheel For
Coated), Motorcycle,
Bumpers. Bicycle Tube ,Container
Trailer
Chassis, Container Locking
Rod , Wheel Disk or Wheel
Rim ( For Painting)
- 28 -
8. COMPARISON OF SPECIFICATIONS
Steel Type JIS JFS EN ASTM SAE
A1011
CQ G3131 SPHC A1001 JSH270C - -
Commercial CS
and A1011
DQ G3131 SPHD A1001 JSH270D - -
drawing DS
steel DDQ G3131 SPHE A1001 JSH270E - - -
EDDQ G3131 SPHF - - - -
Steel for General
G3101 SS400 - - - -
Structure
High Strength Steel
for G3134 A1001 10149
- -
Automobile SPFH490~590 JSH490~590R/W S420MC~S550MC
Structural Uses
G4051 S10C ~ J403
Carbon Steel - - -
S50C 1005~1050
- 29 -
9. Applications
Rims and disks Sprocket
Bicycle parts Automobile parts
Wrench Hydraulic jack
- 30 -
10. Ordering Information
For promptly and properly processing of your orders, please clearly specify the
items as shown in the table below. If you need to confirm any information about
CSVC’s products or services, please feel free to contact with CSVC’s sales or
QC/QA department.
Required Ordering Data Example
Product
1 P/ O Co i l P ic k le d a n d O i l ed C o i l P/ O Co i l
Name
2 Specification and Designation of Grade JIS G3131 SPHC
3 Cut Edge or Mill Edge Mill Edge
4 Surface Quality General Expose
5 Dimensions (Thickness × Width× coil) 1.0mm×1219mm×Coil
6 Inner Diameter 610

Maximum Mass 10 MT
7 Mass Order Mass 150 MT
8 Application and Fabricating Methods Automobile parts
9 Oil Amount 800-1200 mg/mm2
10 Special Requirements(if Required) Show hardness test
Notes:
(1) The contents of this catalog are for reference only. Customers are recommended to
consult the specifications published by the corresponding associations.
(2) Information of the available steel grades, sizes, marking and packing as shown herein
may be updated without notice to comply with actual production situations.
(3) Customers are recommended to confirm with CSVC, should you have any questions
concerning steel specifications or ordering requirements.
- 31 -
11. Unit Conversion Tables
ft in mm m
1 12 304.8 0.3048
Length
0.08333 1 25.4 0.0254
0.003281 0.03937 1 0.001
Weight 1kg=2.20462 lb
Force 1kgf=9.80665 N
ksi（=1000psi） psi kgf/mm2 N/mm2(MPa)
1 1000 0.703070 6.89476
Stress 0.001 1 0.703070×10-4 6.89476×10-3
1.42233 1422.33 1 9.80665
0.145038 145.038 0.101972 1
ft-lbf kgf-m N-m（=Joule）
Absorbed 1 0.138255 1.35582
Energy 7.23301 1 9.80665
0.737562 0.101972 1
- 32 -
12. Notification
(1) If the sides of PO product are mill edge, they will have the potential dangers of
scratching hands.
(2) PO coil has been packed by steel straps, customers are reminded to be careful
when unpack the coil.
(3) For rust prevention, customer can choose oil amount based on application. Even
though steel sheets were applied rust preventive oil, we still recommend that
customers should use product as soon as possible, because rust could be
occurred due to environment condition ( Ex: humidity, acid,…).
- 33 -
--------------------------------------------------------------------------------------------------------------
China Steel Sumikin Vietnam Joint Stock Company
Head Office：My Xuan A2 Industrial Zone, My Xuan Commune, Tan Thanh District,
Ba Ria -Vung Tau Province
Ho Chi Minh Office：Petroland 9F, 12 Tan Trao St., Tan Phu ward, dist.7, Ho Chi Minh
city
1. Technical Service-QC/QA Department

TEL：+84-(0)64-389-2888 Ext. 351, 355
FAX：+84-(0)64-393-2188
2. Sales Services-Sales Department
TEL：+84-(0)85-416-1040 Ext.115, 106
FAX：+84-(0)85-416-1029 or +84-(0)85-416-1030
- 34 -
CHINA STEEL SUMIKIN VIETNAM JOINT STOCK COMPANY
OUR QUALITY, YOUR BETTER LIFE
Feb - 2015

Pickled and Oiled Steel Coils

Uploaded by

Copyright:

Available Formats

Pickled and Oiled Steel Coils

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Pickled and Oiled Steel Coils

Uploaded by

Copyright:

Available Formats

Pickled and Oiled

CHINA STEEL SUMIKIN VIETNAM JOINT STOCK COMPANY

China Steel Sumikin Vietnam Joint Stock Company, a delicate

CSVC implemented its quality management system based on ISO 9001

ISO 9001 ISO 17025

SNI Mark SIRIM Mark

JIS G3131 SPHC/D/E/F, JFS A1001 JSH270C/D/E

Hot Roll coil Pickling and oiling P/O coil

Some pictures of Pickled and Oiled line

Picture 1: Two Pay-Off Reel In The

Picture 2: Laser Beam Welder

Picture 4: Electrostatic Oiler

Picture 5: Tension Reel

4.1 Chemical Compositions and Mechanical Properties

Tensile Test Bendability

0.10 0.45 0.035 0.035 30 32 33 35 37 39 No.5, in No.3, in

0.08 0.35 0.025 0.025 37 38 39 39 40 42

400 255 235 31 32 34 35 36 37

440 305 295 29 30 32 33 34 35

4.1.6 JIS G4051 Carbon Steels for Machine Structural Use

S10C 0.08─0.13 0.30─0.60

S12C 0.10─0.15 0.30─0.60

S15C 0.13─0.18 0.30─0.60

S17C 0.15─0.20 0.30─0.60

S20C 0.18─0.23 0.15~0.35 0.30─0.60 0.030max. 0.035max.

S22C 0.20─0.25 0.30─0.60

S25C 0.22─0.28 0.30─0.60

S28C 0.25─0.31 0.60─0.90

S30C 0.27─0.33 0.60─0.90

S35C 0.32─0.38 0.60─0.90

S38C 0.35─0.41 0.60─0.90

S40C 0.37─0.43 0.60─0.90

S45C 0.42─0.48 0.60─0.90

S48C 0.45─0.51 0.60─0.90

S50C 0.47─0.53 0.60─0.90

Tensile Test Bendability

4.1.8 ASTM A1011 Carbon, structural, High-Strength Low-Alloy Steel and

0.25max. 0.035max. 0.04max. ─ 0.15max. 0.025max.

CS Type A ─ 205/340 25min. 25min. 25min. 25min. ─ Transverse

DS Type B ─ 205/310 28min. 28min. 28min. 28min. ─

SS Gr. 30 340min. 205min. 21min. 24min. 25min. 25min. 1.0t

SS Gr. 33 360min. 230min. 18min. 22min. 23min. 23min. 1.0t

SS Gr. 40 380min. 275min. 15min. 20min. 21min. 21min. 2.0t

SS Gr. 45 410min. 310min. 13min. 18min. 19min. 19min. 2.0t

SS Gr. 50 450min. 340min. 11min. 16min. 17min. 17min. 2.5t

SS Gr. 55 480min. 380min. 9min. 14min. 15min. 15min. 3.0t

SS Gr. 60 520min. 410min. 8min. 13min. 14min. 14min. 3.5t

SS Gr. 70 585min. 480min. 7min. 12min. 13min. 13min. 4.0t

Elongation% Bend Test

1.60≦t＜2.00 ±0.16 ±0.17 ±0.18

2.00≦t＜2.50 ±0.17 ±0.19 ±0.21

2.50≦t＜3.15 ±0.19 ±0.21 ±0.24

3.15≦t＜4.00 ±0.21 ±0.23 ±0.26

4.00≦t＜5.00 ±0.24 ±0.26 ±0.28

5.00≦t＜6.00 ±0.26 ±0.28 ±0.29

t=6.00 ±0.29 ±0.30 ±0.31

(2) JIS G3131 Thickness Tolerances

(3) JIS G3132 Thickness Tolerances

(5) JIS G3134 Thickness Tolerances