Öhlins Front Fork Road & Track

FG 43
Owner’s Manual
 Öhlins Headquarters Upplands Väsby, Sweden

Öhlins Racing AB - The Story

It was the 1970’s, a young man named Kenth Congratulations! You are now the owner of an
Öhlin spent most of his spare time pursuing his Öhlins product. More than two hundred World
favourite sport: motocross. Championships and other major world titles are
Being a careful observer, Kenth’s attention was definitive proof that Öhlins products offer out-
continuously drawn to one specific detail - moto- standing performance and reliability.
cross bikes had more engine power than their Every product has gone through rigorous test-
suspension could handle. It was not long before ing and engineers have spent thousands of
Kenth realised that better performance could be hours, doing their very best to use every possi-
achieved by improved wheel suspension. ble experience from our 35 years within the rac-
Öhlins Racing was established in 1976, and ing sport.
just two years later the company won its first The product that you now have in your pos-
World Championship title. Despite being in the session is pure racing breed that is built to
business for 35 years, the search for perfection withstand.
and new functions is still the main focus of the By installing this product on your vehicle you
company. have made a clear statement… you are a seri-
ous rider or driver with a focus on getting the
maximal handling ability and outstanding feed-
back from your vehicle. Along comes the fact
that your Öhlins product will be a long lasting
friend, delivering the very best of comfort and
performance every time you go for a ride. Go
explore!
safety precautions
General Warnings SAFETY SYMBOLS
11 Note! In this manual, mounting instructions and other techni-
The shock absorber/front fork/steering damper is an impor- cal documents, important information concerning safety
tant part of the vehicle and will affect the stability. is distinguished by the following symbols:

11 Note! The Safety Alert Symbol means: Warning! Your safety

Read and ensure you understand the information in this is involved.
manual and other technical documents provided by Öhlins,
before using the product. ⚠⚠ Warning!
The Warning Symbol means: Failure to follow warning
11 Note! instructions can result in severe or fatal injury to any-
Öhlins Racing AB can not be held responsible for any dam- one working with, inspecting or using the product, or
age to the shock absorber/front fork/steering damper, vehi- to bystanders.
cle, other property or injury to persons, if the instructions
for mounting, usage and maintenance are note followed ✋✋ Caution!
exactly. The Caution Symbol means: Special precautions must be
taken to avoid damage to the product
⚠⚠ Warning!
After installing the Öhlins product, take a test ride at low 11 Note!
speed to ensure your vehicle has maintained stability. The Note Symbol indicates information that is important
regarding procedures.
⚠⚠ Warning!
If the suspension makes an abnormal noise, or the func-
tion is irregular, or if you notice any leakage from the prod-
uct, stop the vehicle immediately and return the product to
an Öhlins dealer. Product Specific Warnings

⚠⚠ Warning! ⚠⚠ Warning!
The product warranty shall only apply if the product has This product was developed and designed exclusively for
been operated and maintained in accordance with rec- a specific vehicle model and shall only be installed on the
ommendations in this manual. If you have any questions intended vehicle model in its original condition as delivered
regarding usage, service, inspection and/or maintenance from the vehicle manufacturer.
please contact Öhlins.

11 Note!
When working with the Öhlins product, always read the
vehicle service manual.

11 Note!
This manual shall be considered as a part of the product
and shall accompany the product throughout its life cycle.

© Öhlins Racing AB. All rights reserved.

Any reprinting or unauthorized use without the written permission of Öhlins Racing AB is prohibited.

3
contents
1 Design.......................................................... 4
2 Adjusters...................................................... 5
3 Setting up..................................................... 6
4 Change spring............................................. 8
5 Oil level........................................................ 9
6 Technical Information................................... 10
7 Inspection and maintenance........................ 11

1 Design

Öhlins Front Fork FG43

The Öhlins front fork uses a cartridge system gives progressive action of the front forks. For
for damping. This gives a damping force which better understanding, please see the oil level
depends on the speed of the piston in the car- chart later in this manual. A telescopic front fork
tridge system. The combination of spring and air depends on smooth friction free action. Make
volume (oil level) offers a possibility to adjust the sure to service your front forks regularly. See
characteristics of the fork to suit different tracks chapter Inspection and maintenance later in this
and riders. For example, a soft spring in com- manual.
bination with a small air volume (high oil level)

4
2 Adjusters
Spring preload adjuster
Use a 17 mm wrench to turn the upper adjust-
ment screw. Maximum adjustment range is
15 mm. One turn of the adjustment screw will
cause 1 mm change in spring preload. Increase
by turning clockwise, decrease by turning
counter-clockwise.

Rebound damping adjuster

Use a hexagon screwdriver (00794-01) or a
3 mm Allen key. Adjustment range from fully
closed valve (clockwise) to fully open valve
(counter-clockwise) is about 20 clicks.

Compression damping adjuster

Use a 3 mm Allen key with a spherical head
(tool 00794-01). Adjustment range from closed
valve (clockwise) to maximum open valve (coun-
ter-clockwise) is 20 clicks.

Rebound and Compression

Recommended setup according to the Mounting
Instructions. Normal adjustment range from orig-
inal position is +/-4 clicks.

✋✋ Caution!
When adjusting, turn carefully not to damage delicate
sealing surfaces.

5
3 Setting up
Below you will find some basic guidelines for
setting up your Öhlins front forks. However, Static sag
you must remember that the front forks are just
one part of your motorcycle and to get it to work
properly, the whole motorcycle has to be set up
according to the vehicle manual.

1
Put your bike on a front stand so you can install
the front forks.
Maximum torque on the bottom triple clamp and A B
steering damper bracket (if it is located on the
diameter of the outer tube) is 15-18 Nm.
Remove the front wheel and brakes.

2
Unscrew the adjustment housing on top of the
fork (use tool 00797-04) on both upper tubes.
Slide the fork up and down gently to make sure
everything works correctly.

3
Make sure the fork is fully extended. Assemble
the adjustment housing again and set your initial
preload of the spring by using a 17 mm wrench
until you achieve a static sag of 25-30 mm.
Each turn gives 1 mm in preload.
Maximum preload: 15 mm

4
The clicks are a bleed function, separate for
rebound and compression damping. Adjust
rebound from the top centre of the fork and com-
pression from the bottom part of the fork. Start
to count from fully closed (clockwise) and set to
the recommended number of clicks (use a 3 mm
Allen key). For recommended setup see the
Mounting Instructions or contact Öhlins.

✋✋ Caution!
When adjusting, turn carefully not to damage delicate
sealing surfaces.

6
3 Setting up
Step 1 - Measure the sag Recommended Measures
Spring preload is a crucial part of setting your If no other recommendations are given
motorcycle since it affects the height of the in the Mounting Instructions follow these
motorcycle and the fork angle. Measure the sag recommended measures:
before setting the spring preload.
Free sag
Rear (R1-R2) 10-20 mm
1. Make sure you are working on a flat surface.
Front (F1-F2) 15-30 mm
Put the motorcycle on a work stand so that
both wheels are off the ground and the Ride height
suspension is unloaded. Rear (R1-R3) 25-40 mm
2. Mark, e.g. with a piece of tape, a point Front (F1-F3) 35-50 mm
immediately above the rear wheel axle.
3. Measure the distance from the marked point Note!
to a fixed point, e.g. the wheel axle (R1). Always check on the Öhlins web site
4. Measure the distance from the bottom of the www.ohlins.com or with your Öhlins dealer for
upper triple clamp to a fixed point, e.g. the latest updates.
front wheel axle (F1).
Step 2
5. Put the motorcycle on the ground so that
the front and the rear suspensions are Adjust spring preload
slightly compressed. Repeat the measuring 1. If your sag measures differ significantly
procedures (R2 and F2). from the recommendations in the Mounting
6. Sit on the motorcycle in normal riding Instructions or the table, adjust the spring
position, properly outfitted in full riding preload. (See chapter Spring Preload in this
gear. Repeat the measuring procedure (R3 manual).
and F3). 2. If the ride height still differs from the
recommendations, you may need to change
to softer/harder spring. Contact an Öhlins
dealer for advice.

Warning!
Incorrect spring rate may result in a front geometry
that is either too steep or too flat. This can result
in a tendency of under or over steering, that could
seriously affect the handling characteristics of the
motorcycle.

7
4 Change spring
Service Tools
Description Part no
Clamp tool 00786-05
Clamp tool 00787-03
Top nut tool 00797-04
Cartridge tool 04702-02
Top nut holder 04705-01

4.1
Loosen the screws that hold the fork legs in the
upper triple clamps. 4.2

4.2
Loosen the top nut assembly approximately 2
turns, use top nut tool (00797-04).

4.3
Remove the fork legs from the motorcycle.

4.4
Put one fork leg in a vice with soft jaws.

4.5
Release the spring preload completely. Use a
17 mm wrench.

✋✋ Caution! 4.6
Do not damage the O-ring. Carefully remove the adjust-
ment housing.

4.6
Remove the adjustment driver, preload tube and
the spring. Note the positions of the parts.

4.7
Pull out the piston rod as far as possible and
turn the compression adjuster screw fully clock-
wise. This will keep the piston rod in top position
which facilitates the installation procedure.

4.8
Install the new spring, adjustment driver and
preload tube. Make sure to put all parts back in the
same position as they were before the removal.

4.9
Reinstall the top nut assembly.

8
4 Change spring
4.10
Fasten the adjustment housing in the fork leg.
Make sure that the fork leg is fully extended
when tightening the adjustment housing.

4.11
Install the fork legs on the motorcycle and set
the preload, compression and rebound accord-
ing to recommended setup data in the Mounting
Instructions or contact an Öhlins dealer for advice.

5 Oil level
Compared to conventional type of front forks, a general card description to facilitate under-
the upside down front forks are very sensitive standing of the difference when the oil level is
to variations in oil level. Therefore, adjust the changed.
oil level with special care. A change in the fork
11 Note!
oil level will not affect damping force in the early
Adjust the oil level in mm according
stage of fork travel, but will have a great effect in
to the figure with the fork fully com-
the later stage. pressed and with the spring and
When the oil level is raised: the pre-load tube removed. For the
The air spring in the later half stage of travel is right recommended level, please
stronger, and thus the front forks harder. see the mounting instruction.
When the oil level is lowered:
The air spring in the later half stage of travel is
reduced thus the front forks are softer. The oil
level works most effectively at the end of the fork
travel. Air spring characteristics shown, refer to

9
6 Technical Information
Fork length Oil Level
See Mounting instructions Please see Mounting instructions for the specif-
ic front fork.
Stroke
See Mounting instructions ✋✋ Caution!
Free spring length Use only Öhlins high performance front fork fluid
(1309-01).
See Mounting instructions
Loctite glue
Rebound adjustment
542 on Fork bottom thread
Basic setting 9-12 clicks
Maximum open valve 20 clicks Tightening torque
Triple clamp bolt 15-18 Nm
Compression adjustment
Basic setting 6-16 clicks Grease
Maximum open valve 20 clicks Öhlins front fork grease 00146-01 (red grease).

Spring preload adjustment

0-15 mm (0-15 turns)

Spring rate
See Mounting instructions.
Optional springs and rates:
Part no Rate (N/mm)

08790-80 8.0
08790-85 8.5
08790-90 9.0
08790-95 9.5
08790-10 10.0
08790-05 10.5
08790-11 11.0
08790-15 11.5

10
7 Inspection and maintenance
Preventive maintenance and regular inspection reduces
the risk of functional disturbance. If there is any need for
Inspection points
additional service, please contact an authorized Öhlins
Service Centre.
4
Clean the front fork externally with a soft deter-
gent. Use compressed air. Be careful that all dirt
and debris is removed. Keep the front fork clean
and always spray it with oil (QS 14, WD40 or
CRC 5-56 or similar) after washing the vehicle.
2
✋✋ Caution!
Never use detergents that can damage the surfaces of the
front fork. Use of thinner and brake cleaner will dry the sur-
faces too much.

11 Note!
Make certain that your front fork is always filled with Öhlins
High Performance Front Fork Oil (1309-01).

Inspection points 1
1. Check the front fork for leakage.
2. Check the front fork tubes for external
damages. 3
3. Check the attachment points of the caliper
bracket and fender bracket.
4. Check the attachment points to the vehicle.

Inspection intervals
Normal use: Once a year or every 5000 km
Race track: Every ten hours

Once every 2nd year (or 20 000 km), general:

Change front fork oil,

11 Note!
Use Öhlins Front fork oil (01309-01) only.

11 Note!
Discarded Öhlins products should be handed over to an
authorized work shop or distributor for proper disposal.

11
 Owner’s Manual | Part No. 07282-04_1 | Issued 2013-09-24 | © Öhlins Racing AB

Your Öhlins retailer:

Öhlins Racing AB
Box 722 Phone: +46 (0)8 590 025 00
SE-194 27, Upplands Väsby Fax: +46 (0)8 590 025 80
Sweden www.ohlins.com