Technical Manual

TECHNICAL MANUAL
For the Design, Construction and

Maintenance of Tennis Facilities
Compiled by the Tennis Queensland

Technical Services Advisory Group
TECHNICAL MANUAL
For the Design. Construction and Maintenance of Tennis Facilities
Compiled by
Tennis Queensland’s Technical Services Advisory Group
Published by
Tennis Queensland
Second Edition – June 2008
© Tennis Queensland, 2008. All rights reserved.
No part of this publication may be reproduced in any form, by Photostat, microfilm, xerography, or
any other means, or incorporated into any information retrieval system, electronic or mechanical,
without the written permission of the copyright owner.
All correspondence concerning this publication should be addressed to:-
The Technical Services Advisory Group
c/- Tennis Queensland
PO Box 2366
Graceville, QLD, 4075
Australia
Printed by Tennis Queensland, Brisbane, Australia
Technical Manual
ACKNOWLEDGEMENTS
First and foremost, the Tennis Queensland would like to thank the Queensland Government
Department of Local Government, Planning, Sport & Recreation for their assistance and support.
Without their financial contribution towards this project, the completion of this manual would remain
an unrealised dream.
The Tennis Queensland Technical Services Advisory Group wishes to thank all organisations and
individuals who have contributed information, diagrams, photographs, opinions and suggestions for
incorporation into this publication. Specific mentions should be made of the following organisations
and individuals who have made particularly significant contributions:
• Tennis Australia for their overall support of our ambitious project and sharing their visions
for the future of tennis in Australia
• The USTA for allowing us to reproduce a number of diagrams from their own publication
“Tennis Courts – A Construction and Maintenance Manual” and convert them into metric
measurements for use in Australian circumstances
• William Loud (Aust) Pty Ltd and Rebound Ace Sports Pty Ltd for their contributions in
relation to asphalt court construction and acrylic / cushioned acrylic court surfacing
• Both Jordin Sports and Rebound Ace Sports Pty Ltd for providing large galleries of
photographs showing a wide variety of tennis courts under construction or recently
completed to compliment our text and to assist the reader to visualise important
information and concepts
• RAW Courts for providing information in relation to the construction and maintenance of
natural clay courts and photographs of numerous pieces of equipment used to maintain of
these courts and also synthetic grass tennis courts
• En Tout Cas for information relating their clay court surfacing products
• Peter Cronin for his expert input into the construction and maintenance of natural grass
tennis courts (based on his skills in preparing grass tennis courts for major events, such as
Australia’s Davis Cup home tie against Russia in Brisbane in 1999)
Finally, the many hours of editing reviews undertaken by Alfred Edwards (a retired BBC and ABC
journalist with a number of commercial editorial credits to his name) is also greatly appreciated by
the members of the Technical Services Advisory Group.
Additional thanks is also passed onto all the members of the general public who provided
invaluable feedback to the initial draft version of this document that was placed on Tennis
Queensland’s web site for comment and review in December 2006. Special mention in this regard
is given to Mr Tim McSweeney, and Engineer from Central Queensland University, whose
extremely detailed review was way beyond the level of feedback we ever anticipated from a this
exercise.
The Tennis Queensland Technical Services Advisory Group members (past and present)
responsible for the preparation of this first edition of this Manual were:
Bruce Lynch (Chairman), Ashley Cooper, Maurice Philp, John Chivers, Paul Bull, Ross Jordin,
Colin Greeves, Michael Blomer and Cherie Murphy.
Technical Manual
INDEX
1 Introduction.................................................................................................................................. 7
1.1 How to use this manual........................................................................................................ 7
1.2 Purpose of the manual......................................................................................................... 7
1.3 Information sources, Standards and Codes. ....................................................................... 7
1.4 Where to get further help ..................................................................................................... 7
2 Facility planning and development.............................................................................................. 8
2.1 Definitions used in this section ............................................................................................ 8
2.2 Background.......................................................................................................................... 9
2.3 Planning ............................................................................................................................... 9
2.4 Choosing a site .................................................................................................................. 10
2.5 Budgeting........................................................................................................................... 11
2.6 Court construction on a “greenfield” site............................................................................ 12
2.6.1 Asphalt base – acrylic surface.................................................................................... 13
2.6.2 Concrete base ............................................................................................................ 16
2.6.3 Lighting ....................................................................................................................... 16
2.6.4 Landscaping ............................................................................................................... 17
3 Facilities development planning ................................................................................................ 18
3.1 Introduction ........................................................................................................................ 18
3.2 Definitions used in this section .......................................................................................... 18
3.3 Project Management.......................................................................................................... 18
3.4 Funding .............................................................................................................................. 19
3.5 Ongoing costs .................................................................................................................... 19
3.6 Information sources, Standards and Codes. ..................................................................... 19
4 General site and construction consideration............................................................................. 20
4.1 Introduction ........................................................................................................................ 20
4.3 Choice of site ..................................................................................................................... 20
4.4 High risk sites..................................................................................................................... 21
4.4.1 Slip areas.................................................................................................................... 21
4.4.2 Uncontrolled fill and other issues................................................................................ 21
4.4.3 Future growth.............................................................................................................. 21
4.5 Court planning.................................................................................................................... 21
4.5.1 Court dimensions........................................................................................................ 21
4.5.2 Court separation ......................................................................................................... 23
4.5.3 Dividing fences ........................................................................................................... 28
4.5.4 Orientation .................................................................................................................. 28
4.6 Vegetation.......................................................................................................................... 29
4.7 Overland flow of water and drainage ................................................................................. 29
4.7.1 Surface water.............................................................................................................. 29
Technical Manual 1
4.7.2 Subsurface water........................................................................................................ 29
4.8 Choice of contractor........................................................................................................... 30
5 Earthworks and subgrade ......................................................................................................... 31
5.1 Introduction ........................................................................................................................ 31
5.3 Site investigation................................................................................................................ 32
5.4 Soil report........................................................................................................................... 32
5.5 Underground flow of water and drainage........................................................................... 32
5.6 Compaction........................................................................................................................ 32
5.7 Retaining............................................................................................................................ 33
5.7.1 Types of walls ............................................................................................................. 33
5.8 Site maintenance ............................................................................................................... 38
5.8.1 Control of vegetation................................................................................................... 38
6 Base construction...................................................................................................................... 39
6.1 Introduction ........................................................................................................................ 39
6.3 Choice of base to suit site conditions, surface choice ....................................................... 41
6.4 Elements common to all bases.......................................................................................... 41
6.5 Asphalt bases .................................................................................................................... 41
6.5.1 Elements of an asphalt base ...................................................................................... 41
6.5.2 Construction process .................................................................................................. 42
6.5.3 Construction failures. .................................................................................................. 43
6.5.4 Deterioration failures................................................................................................... 44
6.5.5 Measures of quality..................................................................................................... 44
6.6 Concrete bases.................................................................................................................. 44
6.6.1 Types of concrete bases ............................................................................................ 44
6.6.2 Reinforced concrete bases......................................................................................... 45
6.6.3 Construction................................................................................................................ 46
6.6.4 Post Stressed concrete bases.................................................................................... 48
6.7 Compacted earth base....................................................................................................... 50
6.8 Proprietary base systems .................................................................................................. 51
6.8.1 Chemically bound systems......................................................................................... 51
6.9 Maintenance and repair of base structure ......................................................................... 51
6.10 Information sources, Standards and Codes................................................................... 51
7 Surface ...................................................................................................................................... 52
7.1 Introduction ........................................................................................................................ 52
7.1.1 Definitions used in this section ................................................................................... 52
7.1.2 Classification of surface systems ............................................................................... 52
7.1.3 Choice of surface........................................................................................................ 52
7.1.4 Advantages and disadvantages ................................................................................. 53
Technical Manual 2
7.1.5 Maintenance issues .................................................................................................... 53
7.1.6 Playing characteristics ................................................................................................ 56
7.2 Acrylic................................................................................................................................. 57
7.2.1 Acrylic hardcourts - types of systems ......................................................................... 57
7.2.2 Acrylic Application....................................................................................................... 58
7.2.3 Some dos and don’ts when coating acrylic tennis courts........................................... 62
7.2.4 Cushion Acrylic ........................................................................................................... 66
7.2.5 Choice of colours for acrylic surfaces......................................................................... 69
7.2.6 Maintenance and repair of acrylic surfaces................................................................ 69
7.2.7 Resurfacing................................................................................................................. 69
7.3 Synthetic grass .................................................................................................................. 71
7.3.1 Definitions used in this section ................................................................................... 71
7.3.2 What is Sand Filled Artificial Grass (SFAG)? ............................................................. 71
7.3.3 Player preferences...................................................................................................... 73
7.3.4 Selecting a synthetic grass product............................................................................ 73
7.3.5 Mineral infill sand ........................................................................................................ 75
7.3.6 SFAG installation ........................................................................................................ 76
7.3.7 SFAG maintenance .................................................................................................... 78
7.4 Synthetic Clay (outdoor carpet) surfaces........................................................................... 80
7.4.1 Introduction ................................................................................................................. 80
7.4.2 Construction................................................................................................................ 81
7.4.3 Synthetic Clay Surface ............................................................................................... 82
7.4.4 Maintenance ............................................................................................................... 82
7.5 Natural Grass Tennis Courts ............................................................................................. 83
7.5.1 Construction................................................................................................................ 83
7.5.2 Grass types................................................................................................................. 84
7.5.3 Equipment................................................................................................................... 84
7.5.4 General Maintenance ................................................................................................. 85
7.5.5 Usage ......................................................................................................................... 85
7.5.6 Preparation - social/competition ................................................................................. 85
7.5.7 Renovations................................................................................................................ 86
7.5.8 Drop in courts ............................................................................................................. 86
7.5.9 Irrigation...................................................................................................................... 86
7.5.10 Grass court maintenance ........................................................................................... 87
7.6 Compacted earth bases..................................................................................................... 89
7.6.1 European Clay ............................................................................................................ 89
7.6.2 Introduction ................................................................................................................. 89
7.6.3 Construction of a European clay court ....................................................................... 90
7.6.4 Choosing a constructor............................................................................................... 90
Technical Manual 3
7.6.5 Equipment for surface maintenance........................................................................... 90
7.6.6 General Maintenance ................................................................................................. 91
7.6.7 Using Maintenance Equipment................................................................................... 92
7.6.8 Decomposed granite................................................................................................... 94
7.7 Information sources, Standards and Codes. ..................................................................... 95
8 Fencing...................................................................................................................................... 96
8.1 Introduction ........................................................................................................................ 96
8.3 Metal fencing...................................................................................................................... 97
8.3.1 Fence height ............................................................................................................... 98
8.3.2 Post installation........................................................................................................... 98
8.3.3 Post size and spacing................................................................................................. 99
8.3.4 Rails and bracing ........................................................................................................ 99
8.3.5 Bracing and strainer wires ........................................................................................ 100
8.3.6 Access ...................................................................................................................... 100
8.3.7 Fence finishing.......................................................................................................... 100
8.3.8 Mesh size (diamond and wire).................................................................................. 101
8.3.9 Dividing fences. ........................................................................................................ 101
8.3.10 Draw back curtains ................................................................................................... 102
8.4 Timber fencing ................................................................................................................. 102
8.5 Attachments to fencing .................................................................................................... 102
8.5.1 Wind screens ............................................................................................................ 102
8.5.2 Sight screens ............................................................................................................ 102
8.6 Maintenance and repair of fencing .................................................................................. 103
8.7 Information sources, Standards and Codes. ................................................................... 103
9 Lighting.................................................................................................................................... 104
9.1 Introduction ...................................................................................................................... 104
9.2 Definitions used in this section ........................................................................................ 104
9.3 Types of lighting systems................................................................................................. 105
9.3.1 Lamp types. .............................................................................................................. 106
9.4 Pole configuration and heights ........................................................................................ 106
9.5 Choice of lighting systems ............................................................................................... 107
9.5.1 Colour temperature................................................................................................... 107
9.5.2 Illuminance................................................................................................................ 107
9.5.3 Uniformity.................................................................................................................. 108
9.5.4 Light Loss Factors .................................................................................................... 108
9.5.5 Glare ......................................................................................................................... 109
9.5.6 Circuit switching........................................................................................................ 109
9.6 Council regulations .......................................................................................................... 109
9.7 Maintenance of lighting .................................................................................................... 110
Technical Manual 4
9.7.1 Lamp maintenance ................................................................................................... 110
9.7.2 Luminaires ................................................................................................................ 110
9.7.3 Light towers .............................................................................................................. 110
9.8 Information sources, Standards and Codes. ................................................................... 110
9.9 Typical Suppliers.............................................................................................................. 111
10 Accessories and amenities.................................................................................................. 112
10.1 Net posts ...................................................................................................................... 112
10.2 Nets .............................................................................................................................. 113
10.3 Centre straps and anchors........................................................................................... 114
10.4 Umpires chairs ............................................................................................................. 114
10.5 Court numbers.............................................................................................................. 114
10.6 Ball machine................................................................................................................. 115
10.7 Ball retrievers ............................................................................................................... 115
10.8 Coaching baskets......................................................................................................... 115
10.9 Hit walls and rebound nets........................................................................................... 115
10.10 Other court accessories ............................................................................................... 115
10.11 Off court accessories.................................................................................................... 116
10.12 Security and safety....................................................................................................... 116
10.13 Suppliers of tennis court accessories........................................................................... 116
10.14 Information sources, Standards and Codes................................................................. 117
11 Indoor tennis, enclosures and roof structures ..................................................................... 118
11.1 Introduction................................................................................................................... 118
11.2 Court enclosures. ......................................................................................................... 118
11.3 Requirements of the rules ............................................................................................ 118
11.3.1 ITF Recommendation on ceiling heights .................................................................. 118
11.3.2 Construction Manual – USTA ................................................................................... 118
11.3.3 Guidance Notes – LTA (Britain)................................................................................ 119
11.4 Types of roof structures................................................................................................ 119
11.4.1 Rigid structures......................................................................................................... 119
11.4.2 Membrane structures................................................................................................ 119
11.4.3 Inflatable structures .................................................................................................. 119
11.5.1 Rules and guidelines ................................................................................................ 120
11.5.2 Suppliers on the Internet. ......................................................................................... 120
12 Club facilities ....................................................................................................................... 121
12.1 Introduction................................................................................................................... 121
12.1.1 Layout ....................................................................................................................... 121
12.1.2 Size requirements..................................................................................................... 121
12.1.3 Other provisions........................................................................................................ 122
Technical Manual 5
13 Managing a project .............................................................................................................. 123
13.1 Introduction................................................................................................................... 123
13.2 Definitions used in this section..................................................................................... 123
13.3 Obtaining technical guidance ....................................................................................... 123
13.4 Site investigation .......................................................................................................... 124
13.5 Preparing a technical specification............................................................................... 124
13.6 Inviting tenders from the construction industry ............................................................ 124
13.7 Choosing between tenders .......................................................................................... 126
13.8 Contracts and project acceptance................................................................................ 126
13.9 Project supervision ....................................................................................................... 127
13.10 Progress payments and retentions .............................................................................. 127
13.11 Repairs under warranty ................................................................................................ 128
14 Care and maintenance of tennis courts............................................................................... 130
14.1 General maintenance ................................................................................................... 130
14.2 Hard court and cushioned hard court maintenance ..................................................... 130
14.3 Indoor acrylic surfaces ................................................................................................. 131
14.4 Hard court maintenance equipment ............................................................................. 131
14.5 Sand filled synthetic grass maintenance...................................................................... 131
14.6 Grass court maintenance ............................................................................................. 132
14.7 Clay court maintenance................................................................................................ 132
14.8 Court equipment maintenance ..................................................................................... 132
14.8.1 Installing a tennis net. ............................................................................................... 132
14.8.2 Net maintenance....................................................................................................... 132
14.8.3 Net post maintenance............................................................................................... 132
14.9 Windscreens and windscreen maintenance ................................................................ 133
14.10 Landscape maintenance .............................................................................................. 134
15 Document control ................................................................................................................ 136
15.1 Date of preparation....................................................................................................... 136
15.2 Review date.................................................................................................................. 136
15.3 Disclaimers................................................................................................................... 136
16 APPENDICES ..................................................................................................................... 137
Technical Manual 6
1 Introduction
1.1 How to use this manual
This manual has been prepared by the Tennis Queensland Technical Services
Committee to assist affiliated clubs and associations, Local Government, educational
institutions and others from the tennis community to make sound choices when
constructing or maintaining tennis facilities.
It is not intended that this manual will replace advice provided by professionals such as
engineers, architects and registered court builders. Nor is it meant to be used as a “do it
yourself” manual for prospective court owners, clubs, associations or other organisations
in lieu of engaging professional project managers and design consultants. Rather, it
provides a framework that will permit those in the tennis community to communicate with
service providers and make informed decisions on options offered.
Tennis Queensland cannot be held liable for any loss or damage incurred as a result of
any person who relies upon the information contained within this publication. Advice
should always be sought from qualified design professionals with the specific expertise
relating to the any proposed works.
Members of the tennis community are encouraged to study this manual at the earliest
conceptual stage of a project so that they can go to the market in an informed manner.
1.2 Purpose of the manual

This manual has been prepared by Tennis Queensland to provide assistance to affiliated
clubs and associations, local government, educational institution, and members of the
public to assist them to understand technical aspects of tennis court construction and
maintenance.
1.3 Information sources, Standards and Codes.

Resource material is available from the following sources:
Standards Australia building codes at www.standards.org.au
International Tennis Federation www.itftennis.com
Tennis Australia www.tennis.com.au
Tennis Queensland www.tennisqueensland.com.au or via www.tennis.com.au and select
Queensland from the States menu option
United States Tennis Association www.usta.com
1.4 Where to get further help

The Tennis Queensland Technical Services Committee can provide initial technical
advice to affiliated clubs and associations at no cost. More detailed advice, ranging from
site inspections, preparation of technical specifications, management of tendering
processes through to full project management can be provided on a fee for service basis.
The fee for service project management can also be provided to non-affiliated bodies,
companies and individuals. Services can range from inspection and report on existing
facilities, project evaluation, preparation of technical specifications, calling and evaluation
of tenders and full project management.
Please contact Tennis Queensland if you would like further information on the services
provided.
Technical Manual 7
2 Facility planning and development
2.1 Definitions used in this section
25MPa This is a measure of the strength of concrete.
95% standard The specification for a measure of compaction. This term may be
used by an engineer when determining how a fill platform will be
constructed.
Asphalt Plant Manufacturing facility at which raw asphalt is produced.
Cut to fill The act of cutting material from the high side of a slope and placing
it in compacted layers at the low side to create a level platform.
Drainage falls The parameter of a platform wherein a specific slope is designed
into the court surface so that surface water will drain away from the
playing area.
F72 mesh This is a measure of the size/strength of the reinforcing mesh used
in the construction of concrete platforms.
Fill embankment The embankment created when filling the low side of a cut to fill
site.
Geotechnical A report on the ground condition prepared by an appropriately
report qualified engineer. This will report such factors as compaction,
moisture levels, the potential for the ground to swell or shrink as
moisture levels change, etc.
Geotextile Material used to strengthen compacted ground, provide a filter
barrier around rubble drains, etc.
Granular/clay A general description of courts constructed of decomposed granite,
clay, ant bed, etc.
Ground water Subterranean water that can change subsoil moisture conditions.
Hard courts A generic description of courts constructed of concrete, asphalt and
similar hard surfaces. Hard courts are characterized by a high
bounce.
Post- tensioned A form of construction for a concrete platform wherein conduits are
concrete placed in the platform when it is cast and reinforcing ‘cables’ are
subsequently tensioned to give the platform its strength
Reactive The property of soil that causes it to swell when moisture content
increases and shrink when moisture content reduces. The
resulting ground movement may cause damage to a poorly
designed court.
Soft spots Areas of ground that have different compaction. Typically, these
could be areas where tree roots have been removed and
insufficient attention has been paid to compaction when the holes
were filled. Soft spots may also be caused by moisture collecting.
Spoon drains Surface drains designed to collect water and direct that water to
collection points
Subsoil That stratum of ground located under the court platform.
Sub-soil trenches Trenches of granular material, usually including slotted drainage
pipe, designed to collect underground water and direct it to
drainage points.
Surface lamination A situation where the acrylic surface bubbles or peels off the base
structure
Technical Manual 8
Swale Raised earth mound designed to divert the overland flow of water
in a particular direction.
Swell / shrink A measure of the amount of change in volume of soil with changes
characteristics to the moisture content.
Uncontrolled fill Fill that has been placed on the site without the supervision of an
engineer. The characteristics of this fill are therefore unknown and
construction should not proceed without appropriate testing of the
compaction, etc
Water table Naturally occurring (usually) water that lies below the surface. The
level of this water may vary with the seasons.
Wind loadings This is the pressure created by the wind hitting the court
windscreens. This is an important design parameter and must be
considered when attaching wind screens to existing structures such
as court fences.
Windscreens Screens erected to divert wind away from a tennis court.
2.2 Background
Tennis is an integral part of community life throughout Australia, and forms an important
part of our social structure. Competition within the leisure and sports market is now much
broader and more fiercely contested than in years gone by, with today’s consumers
becoming more demanding and discerning. Therefore, it is in every club’s best interest to
provide quality facilities that are clearly being well maintained.
Unfortunately, however, many of our tennis facilities need significant upgrading or even
complete rebuilding. There are also a number of regions throughout the state that have,
and will continue to experience, substantial population growth. Many of these areas are
subsequently suffering from a shortage of tennis facilities, requiring the construction of a
number of major new centres to cater for this community demand.
The vast majority of current facilities are managed by ‘not for profit’ organizations, and
have been built on council owned land. These clubs and associations, in the main, rely
on government and council funding grants to maintain their facilities. There are some
exceptions, most notably Brisbane, where privately owned tennis centres provide the
backbone for the sport. These centres are also under threat as operating costs and the
capital value of land occupied offer more attractive re-development options to facility
owners.
Both these groups of management are currently under pressure to maintain their facilities
in top condition. The ‘not for profit’ organizations are competing with ever increasing
demands on council and state/ federal governments resources for funding. The private
court owner faces escalating land valuations, and consequently increased rates and
taxes. The net result of this is that tennis facilities are deteriorating, and becoming less
attractive to the paying public. In addition, a great many of these facilities have not been
properly designed and have been built by accepting the cheapest quote. In many cases,
the only real alternative is to demolish them and start again.
With that in mind, let’s go through the stages that should be taken in building or re-
building a tennis facility.
2.3 Planning
First we must establish the market and the availability of a suitable site. Existing facility
operators should know their market well, but additional factors can emerge. Would
leasing or hiring some of their courts to a professional coach increase the number of
players using the facility? A number of case histories show that a professional operator
increases use by a substantial amount.
Technical Manual 9
Consideration should be given to realistic membership numbers and the likely long term
requirements of these members with regards to the facilities to be provided. A good
source of such information is any other clubs that you may know of that have recently
gone through a similar process. The best and most up to date advice is likely to be
available by contacting the Tennis Australia member association in your state or territory,
e.g. in Queensland contact Tennis Queensland. These member associations have a
Technical Services group who can offer expert advice on all facets of developing tennis
facilities.
In establishing the market, take into account all of the community groups who could
potentially utilise the facility. Tennis coaching, organised fixtures and social activities play
a major role in establishing a vibrant tennis club.
To assist with establishing the number of courts on a population basis, the following
tables can be used as a guide:
Population No of courts
15,000 20
25,000 30
50,000 50
100,000 80
250,000 130
500,000 210
750,000 270
1,000,000 320
Studies also indicate that facilities should be planned based on population within 15 – 20
minutes driving time from the site.
2.4 Choosing a site

Site selection is critical, and a thorough investigation
of subsoil and drainage conditions is mandatory.
More often than not, a site set aside by local councils
for recreational activities is leftover land not suitable
for construction of buildings. In the past this was not
a huge problem for tennis courts, as the surfaces
used were grass or variations of a granular porous
surface [decomposed granite, loam, ant-bed,
en-tout-cas etc]. These courts could cope with
ground movements as they were constantly being
well maintained, and in a great number of instances,
by volunteer labour.
Today, maintenance costs have become a huge factor and the shift has been to hard
courts, and variations of synthetic grass carpets. These types of courts require a well-
engineered and constructed base, as ground movements and poor drainage can make
them unplayable.
Often, sites set aside for recreational purposes will have the following problems in one
form or another:
1] Area contains uncontrolled fill
2] Has a high water table
3] Has an extremely poor soil condition
4] Has bad drainage
5] Is flood prone.
Careful analysis of costs in constructing a long lasting base on sites having any of the
above characteristics should be carried out prior to proceeding. On no account should
any construction proceed on any site without taking measures to prevent short-term
Technical Manual 10
failure in the base. A comprehensive geotechnical report and cost estimates based on
this report must be carried out.
The best solution is to avoid sites with soil and drainage problems. The land may be
cheap and / or available, but there is always good reason for this situation.
As a minimum, a suitable site should meet the following requirements:
• Recommended court size is 36.6m x 18.3m. However with vegetation removed,
drainage, and the fact that the finished court platform should finish higher than any
immediate surrounding land, an area of 44m x 25m should be set aside for each
court. This also allows for walkways etc.
• Compactable soil is preferred. Highly reactive clays should be avoided.
• Ideally the site should be away from traffic noise and sheltered from prevailing winds.
• Site should have no large trees within 20m of the fence line.
Recommended court size (ITF full size court)
2.5 Budgeting
In preparing a budget once a suitable site has been located, and the demand for tennis
courts has been determined, allow for full sized courts with the recommended
International Tennis Federation distances between baselines and sidelines. These
dimensions are demonstrated in Section 4.5.1 of this manual.
Be aware that court sizes less than 36.6m x 18.3m are not considered suitable for
professional or elite junior tournament play. In the future this requirement may become
more important, so budget for full size tennis courts where possible.
In addition, funding for the following activities should be included in the budget:
• Feasibility study
• Site acquisition and any associated legal costs
• Planning and design
• Design contingency and construction contingency allowances
• Local authority permits and fees
• Other statutory fees and charges
• Site investigation and soil testing
• Site preparation
• Site drainage and grading
• Site utilities
Technical Manual 11
• Court construction, including base construction and surface construction
• Fencing
• Court lighting and site lighting
• Construction of related facilities [service building, seating, shade structures, pro shop,
clubhouse, maintenance storage etc]
• Car parking [check local authority requirements]
• Accessories and amenities, including any loose furniture and equipment
• Landscaping, walkways
• Operations and disabled access requirements.
• Any site factors that may result in potential public liability insurance issues
2.6 Court construction on a “greenfield” site

Let us assume that all the planning, feasibility studies, council permits etc have been
carried out, and the chosen site is ready to go. If the choice of surface is other than
natural grass or a granular/clay, then the following steps should be taken.
Once plans for the layout of the courts, clubhouse, pathways, car-parking and drainage
system have been established, then a thorough geotechnical analysis of the existing soil
condition should be undertaken. Site history may give an indication of what to expect, but
a geotechnical report should be mandatory so that the base may be designed to stand
the test of time.
If the geotechnical report indicates good sub-grade materials, with little swell / shrink
characteristics and materials that can be compacted, then an asphalt base may be
chosen. The choice of asphalt will become more attractive if a number of factors are
present:
Technical Manual 12
1] Non-reactive soil
2] Asphalt plant within easy access
3] More than 1 or 2 courts being constructed.
If a single or double court is to be constructed, then reinforced concrete may be the better
alternative. Concrete is probably the only choice if the soil condition indicates high
reactivity, or the site could be subjected to periodic flooding. In some cases post-
tensioned concrete should be the choice. Many areas in Australia have highly reactive
soils. Courts built in these areas with under-designed bases have failed within a short
period of time. This decision must only be made with assistance from a geotechnical
engineer.
2.6.1 Asphalt base – acrylic surface

Let us assume the site we have chosen has good subgrade characteristics, and we are
constructing a 6-8 court complex with access to an asphalt plant.
The site should first be cleared of all vegetation and topsoil, and court platforms
established. Topsoil can be stockpiled for later use. If trees are to be cleared, then the
tree roots must also be removed. If tree roots and/or topsoil are left on site, then fungal
growth and settlement can occur under the courts some time in the future.
Holes left by tree root removal should be filled with crushed rock material compacted in
layers.
More information on site preparation is contained in Section 4.
The court platforms should be cut to provide the required drainage falls in one plane.
This can be end to end, side to side, or diagonally. The fall should be a minimum of 1%
in the one plane. In most cases, the platform is cut with a 1% slope end to end, and a
0.5% slope side to side. This delivers a diagonal fall of approximately 1.1%.
Each court or multiple court platforms should be constructed so that it is at least 150mm
higher than any immediately surrounding land. This ensures that, in combination with
sub-surface drainage, no ground water can seep under the court platform.
The courts should be aligned north-south, but may be a few degrees off this alignment if
site conditions favour this alternative. In Australia the western sun causes the most
discomfort for playing, so a court may be aligned a few degrees east of north to
compensate for this factor.
The platform should also be cut so that surface drainage can be adequately disposed of.
It is not desirable to have surface water drain across more than three courts, as drying
time can be delayed, and cause problems in conducting fixtures and tournaments.
In addition, for Australian conditions, it is preferable to have the courts drain from north to
south, or diagonally to the southeast or southwest. This will facilitate drying in the winter
months.
Proper drainage is most important, and must be catered for in the initial cutting out or
establishing the court platform. Ground water seeping under the court surface or water
tables rising to just beneath the playing surface will cause problems in the future. Sub-
soil drainage should not be installed beneath the court base. Water getting under the
base can cause movement of lighting poles, net posts and fence post foundations,
surface lamination and heaving of the surface. Further information is provided in
Section 4.7.
Drainage can be a combination of swales, spoon drains and sub-soil trenches around the
exterior of the courts. In some cases, a grated drain [not a spoon drain] may be
necessary to prevent surface water running across a battery of more than three courts.
Before proceeding with base construction, the platforms should be proof rolled, and any
‘soft spots’ cut out and replaced and compacted with suitable fill. If the platform consists
of a ‘cut to fill’ construction, then all fill must be compacted in layers of not more than
150mm. The platform thus created should be at least 2metres longer and 2metres wider
Technical Manual 13
than the court fence line dimensions, i.e. 38.6metres x 20.3 metres. Further detail on
compaction is provided in Section 5.6.
Beyond this platform the ground should slope away in all directions so that the entire
platform is at least 150mm above the swale or slope thus created.
Wherever possible it is best to create the platform slope back into the cut location. This
prevents any surface run-off water running over the filled slope and causing erosion. The
surface run-off water must then be collected and disposed of so that it does not run back
under the court.
If it is not possible to slope the court back into the cut because of site constraints, then
surface water must be channelled away from the fill embankment. This can be done by
way of a spoon drain or upright kerb outside the fence line. The water must then be
collected in a sump and piped away to an appropriate discharge point.
Some sites will require retaining walls to
stabilise cut and fill. There are many
types of retaining walls, and generally
the site will be the major factor in choice
of wall. Information on retaining walls is
provided in Section 5.7. Appropriate
drainage both behind and in front of the
wall is important in achieving a stable,
long lasting result. Diagrams indicating
types of walls and the required drainage
systems are included in this section.
It is not desirable to have an uphill retaining wall form part of the fencing base, as balls
will rebound off the wall and back into play. The fence should be placed inside the wall,
with the appropriate seepage drain outside the fence line.
Once the court platform has been cut, compacted, and conforms to the designed falls, the
construction of the asphalt pavement can begin.
Prior to placement of the crushed rock, any lighting conduits required to be under the
court surface should be put into place. All residue from the conduit trenches should be
removed from the platform so that it does not get mixed in with the crushed rock.
The thickness of the crushed rock base will be determined by the geotechnical survey,
but in most cases should not be less than 150mm. In some cases a geotextile
membrane may be specified to be placed over the subgrade prior to the placement of the
gravel.
Prior to the gravel placement, an edging strip of either reinforced concrete or treated
timber should be placed to contain the crushed rock and asphalt surface, and to provide a
neat finish. This must be constructed to reflect accurately the falls incorporated in the
court surface. One section of the perimeter edging can be left out and placed after the
asphalt layer has been completed. This will allow construction machinery to enter and
exit the platform.
The crushed rock-base should be rolled
and compacted to not less than 95%
standard, and trimmed so that the design
fall in one plane does not exceed + or
−10mm in any 3 metre section in any
direction.
Before proceeding with the placement and
compaction of the crushed rock pavement,
any light-pole foundations that may be
designed to be placed between courts, i.e.
interior light poles in a battery of two or
more courts, should be put in place. The
Technical Manual 14
appropriate foundation design for the choice of lighting is dealt with in Section 9.
Once the light pole foundations with the rag-bolt assembly have been installed, the
protruding bolts should be wrapped and protected from damage that may be done by the
asphalt paving machine and roller.
Any residue from the excavations for the light-pole foundations must be totally removed
from the platform before placing the crushed rock.
The crushed rock base should then be primed with hot-cut-back bitumen prior to the
laying of the asphalt. This should be allowed to dry for a period of 48 hours. The asphalt
can then be placed in the design thickness [not less than 25mm] by an asphalt paving
machine.
Great care should be taken with the joins in the asphalt strips. Too often close attention
is not paid in this area, resulting in settlement along the joins within a short period. The
asphalt density must be maintained along every joint.
Rolling is also important. Each “run" of asphalt will be initially rolled in the direction of the
paver run, but it should also be thoroughly rolled across the runs at the completion of the
job. Further detail on asphalt construction techniques is contained in Section 6.5 of this
manual.
If the surface is to be an acrylic or cushioned acrylic, then the asphalt must be cured for a
minimum period of 28 days prior to commencing the surface application. The application
of acrylics is detailed further in Section 7.2 of this manual.
While the asphalt is curing is a good time to install the fencing, net-posts and net-strap
holders, lighting poles etc. Care must be taken with equipment on the asphalt surface. A
crane operating outside the constructed court area should install lighting poles.
Net-post and fencing-post foundation excavation should not be made with a motorised
boring machine, as this will cause mounding in the asphalt pavement. The foundations
for net-posts and net-strap holders should be installed by hand, using an electric Kanga
Hammer and attachments. Positioning of the posts is critical, as the court set-out and
line marking will be dictated by the net-post positions.
Foundation holes should be widened at the bottom, and the suggested dimensions are
600mm wide at the top, 900mm deep, and 750mm wide at the bottom. There is
sometimes a tendency for contractors to dig the foundation hole just deep enough to
accept the net-post sleeve, with the hole narrowing at the bottom. This will result in the
net-post leaning inwards a few years down the track. The only remedy for this is to dig
out the foundation, and start again.
Rather than set the post directly into the foundation, a net-post sleeve should be installed
with the top of the sleeve some 6mm above the finished court surface. This will prevent
the sleeve filling up with water during rain.
There is a variety of net-posts available, however it is best to choose one with an internal
winding mechanism, with winding handles that fold flat against the post when not in use.
Protruding handles are not desirable.
Fence-post foundations should be excavated in a similar manner to the net-posts. If the
use of windscreens is contemplated, then the fence must be designed to cope with
increased wind loadings. This can be done either by additional bracing of the fence, or
by using increased diameter posts where windscreens are to be installed.
Fencing is usually designed to be 3m or 3.6m high, and at least a bottom rail is
recommended. Both top and bottom rails are preferred, as this will hold the shape of the
mesh.
A bottom rail prevents the mesh becoming misshapen with use, and will eliminate tennis
balls being lost under the fence. The bottom rail must be positioned about 25mm above
the finished court surface. This will prevent balls escaping, but will allow drainage and
prevent leaves and debris building up against the fence.
Technical Manual 15
If courts are constructed side by side or in a battery, then the dividing fence may be
lowered to 1.2m high through the central section. Positioning of light poles may dictate
the lower area, and some examples of fencing configuration are shown on the following
pages.
Wind-screening to the perimeter of the court[s] is desirable. Allowances should be made
in the court design for spectator viewing.
There are several types of fencing available, and they include galvanised, powder coated
or PVC coated.
Installation of the fence-post footings should be by hand, and designed to cope with the
prevailing ground conditions and wind loadings. If wind-screens are used, then the fence
posts must be upgraded or braced to withstand the wind loading. The fencing can be
designed with either square or cut-off corners. If truncated corners are used on a full
sized court, then allow for 3 metre truncations. The truncated corners allow for a few
desirable factors –
• More aesthetic appearance
• Gate entrance to each court at corner of court
• Elimination of ‘dead ball’ corners.
The wire mesh should always be hung on the inside of the court, with care taken not to
damage the asphalt surface during this procedure.
More information and detail of fence construction is available in Section 8 of this manual.
2.6.2 Concrete base

Construction of a concrete base is provided in detail in Section 6.6 of this manual. As
previously stated, concrete should be the choice if a single or double court installation is
contemplated, or existing sub-grade conditions dictate an asphalt base would not be
suitable. A geotechnical investigation must be carried out on any site that may have
potential problems – expansive soils or uncontrolled fill etc.
Once this report is available, the concrete base can be designed to cope with prevailing
conditions. In some cases, the only course of action would be to construct a post-
tensioned slab. Using a basic concrete specification of 100mm of 25MPA concrete and
F72 mesh on ground with high plasticity will not work. Within a few years the court may
be unfit for play.
Apart from the base material chosen, the other aspects of the tennis facility design and
construction would be the same as for an asphalt base.
2.6.3 Lighting
Lighting design and lighting levels are covered in more detail in Section 9 of this manual.
Lighting levels should be determined by the proposed use of the courts. As a guide, the
following levels are deemed the minimum for varying uses:
Standard Average Uniformity

Tennis Club Residential. 300 lux 2.0
Social Play
Tennis Club Advanced 500 lux 2.0
Fixture play
Satellite Challenger 750 lux 1.7
International Satellite 1,250 lux 1.5
Challenger
When designing the lighting levels and lighting-pole layout, take into account the wind-
load ratings for the locality and type of fittings used. A lighting engineer or qualified
contractor will be able to provide recommendations for the appropriate foundations to suit
the location. The lighting installation and aiming of the lights should be completed prior to
Technical Manual 16
applying the court surface. All construction and erection of fences, light poles, net-post
sleeves etc should be completed before the court surface is laid.
2.6.4 Landscaping
A very important part in the general appearance and attractiveness of a tennis complex is
the landscaping. Incorporated with the landscaping should be an irrigation system
carefully installed so that no water from the equipment sprays onto the court surfaces.
Additionally, there should be hose fitting placed so that each court surface can be
washed without having to resort to long lengths of hose.
Drinking fountains placed at strategic positions and connected to appropriate drainage
should be incorporated. Shade structures for the comfort of players and spectators
should be placed adjacent to the courts. It is not recommended that they be between the
courts, as competition rules do not allow spectators or supporters to be on court. A
couple of simple shade structures or umbrellas may be placed between courts for the use
of players only.
In choosing the landscaping bushes and shrubs, be very selective. Do not plant large
trees or plants that have invasive root systems. Keep all planting away from the court
fencing. Leaf drop will become a maintenance problem, and large trees in any type of
wind will deposit a great deal of debris onto the court surface.
Look for attractive small bushes and shrubs that are compatible with the soil and climatic
conditions of the locality. Low maintenance and low water dependant plants are
desirable. Have some grassed areas incorporated, as these can be used on various
occasions.
An attractively landscaped tennis centre will attract players. A weekly inspection will
detect areas that need attention or replacement. A daily walk around the facility will be
necessary to pick up dropped paper cups, food wrappers etc. If the area is kept in a
clean and tidy, patrons will be encouraged to reciprocate and do the work for you.
Technical Manual 17
3 Facilities development planning
3.1 Introduction
Having established the feasibility of a refurbishing, expanding rebuilding or constructing a
new facility, there are still many steps yet to be taken before we arrive at a well finished
and fully operational tennis facility. This process is generally best controlled by an
experienced Project Manager, preferably with a solid understanding of the intricacies of
developing a tennis facility.

Life Cycle Costing Study undertaken to compare not only the initial installation costs
but also the ongoing costs to maintain the serviceability of a facility
or an element of that facility (i.e. the playing surface of a tennis
court) over a fixed period of time with other available alternatives
Orientation Axis upon which the length of a tennis court is placed (i.e. North-
South or East-West)
Project Suitably qualified expert who is engaged by a client to oversee the
Management design and construction processes of a project (in this instance,
tennis related facilities).
3.3 Project Management

Many club’s and tennis centre owners have tried to manage the design and construction
processes of their new or improved facilities with varying degrees of success. Some
clubs are fortunate enough to have had a committee and/or club member/s with sufficient
skills to manage this task, which can take anything from a few months to a few years to
progress from the feasibility stages right through to the completion of construction. At
times this can be a very time consuming role, and given most clubs rely on volunteers,
this can impact on the ability of these people to maintain control and progress of the
development through to completion.
Whilst many of these people are familiar with the basic requirements of a tennis court and
associated ancillary structures, many have very little comprehension of the specialist
engineering knowledge that is required in the design of such structures. Some of these
design considerations will be discussed in detail throughout this manual to give the
average club member at least a rudimentary understanding of these requirements.
There are all too many horror stories of courts that have been built without taking into
account the prevailing soil conditions, insufficient provisions for site drainage, using the
wrong materials, poor construction practices or even something as simple as the
incorrect court orientation in relation to the sun. A failure to take some or all of these
sorts of issues into account can lead to substantial or even catastrophic failures of the
courts themselves, all in a relatively short space of time.
Significant ongoing maintenance costs or rectification works could end up being as
expensive as the original installation costs or more, especially if it means demolition and
starting again. In many instances, these bodies would have been far better off engaging
a specialist Project Manager to oversee their project to ensure clubs are not exposing
themselves to such risks. This is particularly relevant to smaller clubs who struggle for
many years to raise the capital required to undertake such relatively major works.
For the sake of a small proportion of the overall development costs, the engagement of a
well qualified Project Manager should considerably minimise their client’s risk exposure.
Not only could a good Project Manager save these bodies from costly mistakes during
design and construction, they should also be able to provide advice regarding life cycle
costing issues, which are equally important to all court owners. (Life cycle costing is
discussed in more detail a little later in this Section of the manual.) The last thing a client
wants, after outlaying good money for their facility, is to be burdened with the heartache
Technical Manual 18
of considerable ongoing maintenance costs for many years to come due to decisions
made during design development without such forethought.
As previously stated in the previous section of this manual, the best and most up to date
advice is likely to be available by contacting the Tennis Australia member association in
you state or territory, e.g. in Queensland contact Tennis Queensland. These member
associations have a Technical Services group who can offer services from expert advice
on simple issues right through to full Project Management of major capital works projects.
3.4 Funding
Funding grants for sporting clubs are available from all levels of government, Federal,
State and Local. Further information can be obtained from these bodies or by contacting
Tennis Queensland.
Tennis Australia and Tennis Queensland offer facility development loans at very
competitive rates for affiliated clubs and associations. Further information can be
obtained by contacting Tennis Queensland
3.5 Ongoing costs

Whole of life or life cycle costing.
When choosing elements of a facility the ongoing maintenance costs need to be
considered as part of the establishment cost. For example, choosing a budget priced
acrylic surface with a shorter service life may cost more in the long run than a quality
product. Replacing a budget product may also introduce problems as the lesser product
may require significant effort and expense to remove prior to replacing it with a quality
product.
Similar issues apply for other surface products, fencing, lighting and particularly base
construction.

Not applicable.
Technical Manual 19
4 General site and construction considerations
4.1 Introduction
Choice of site is important. In addition to location, access and those other factors that
provide access to members and therefore membership growth, the geotechnical
conditions of the site have a significant effect on construction and maintenance costs.

Cut-off drains Trenches of granular material, usually including slotted drainage
drainage points.
ITF International Tennis Federation. The ITF is the governing body of
the sport of tennis. The ITF publish the rules of tennis on their web
site at www.itftennis.com.
Overland flow of Water flowing across the surface of the ground caused by rain etc.
water This may be greater than expected where rainfall is collected by
large impervious areas such as car parks and roofs of structures.
Reactive The property of soil that causes it to swell when moisture content
designed court.
Shrink/swell A measure of the amount of change in volume of soil with changes
to the moisture content.
Subgrade Describes the earth structure underneath the court base.
Uncontrolled fill Material that has been used to fill depressions, valleys etc that has
not been selected and/or placed under appropriate supervision.
Uncontrolled fill presents as a major future risk to construction
work.
4.3 Choice of site

Generally, sporting clubs seize the opportunity to take any land made available to them.
As expected, this is often land that is not suitable for other purposes due to location,
instability etc. These high risk sites need careful assessment by appropriate
professionals before construction of development is contemplated.
Technical Manual 20
4.4 High risk sites
4.4.1 Slip areas

Areas close to hillsides where instability occurs require particular engineering
approaches. These areas are often subject to Local Government regulation regarding
type of building work that can be carried out and engineering required for that building
work. These engineering requirements can add significantly to construction costs but
must not be compromised.
4.4.2 Uncontrolled fill and other issues

“Uncontrolled fill” refers to sites that have been re-profiled, usually by the introduction of
imported material, without appropriate engineering supervision or treatment.
Imported fill must be carefully selected to ensure it does not contain material that will
change its characteristics over time or with changes to environmental conditions, such as
moisture content.
Sound engineering requires that fill be
compacted in layers as it is built up to the
final levels. If this is not done it may settle
unevenly over time. This settlement can
destroy all building work that has been
performed, including tennis courts. There
are many examples of tennis courts in
Queensland that have become unplayable
due to uneven settlement of the ground
(Subgrade) under the court. The cost of
rectification of a court damaged in this way
may exceed initial construction costs.
Often, a former dump site may be covered by compacted earth and made available to
sporting clubs. The dump material may include chemical drums, refrigerators, old car
bodies, tyres, logs and tree stumps, etc. These degenerate over time and collapse
leaving a void underground. As the earth settles to fill the void, building construction
above, including tennis courts, collapses.
4.4.3 Future growth

Consider future growth when committing to a site. This includes future courts, car parks,
club facilities etc. Careful planning when constructing the first one or two courts will avoid
costly future problems as a club outgrows a site and seeks to relocate. Relocation of a
club lays waste all that has been done in the past.
4.5 Court planning

The following issues need to be considered when planning a facility.
4.5.1 Court dimensions

The standard dimensions of a court (fenced area) are laid out in the ITF Rules of Tennis.
Although the game is best played on a full sized court (36.6m x 18.3m) the ITF provides
for a minimum recommended size (34.77m x 17.07m).
Additional space requirements exist for stadium courts. This allows room for the
additional umpiring staff and ball persons. The provision of a minimum size allows
compromise where site or financial constraints prevent full size courts from being
constructed.
Construction of courts below the ITF minimum recommended size is not recommended.
In addition to corrupting the game and thereby reducing enjoyment for the players,
smaller courts may present a safety risk for players and expose the court owner/operator
to risk of litigation for injuries incurred from collision with fences or other obstructions
placed inside the recommended playing area.
Technical Manual 21
Where sufficient space is available, courts smaller than the ITF minimum recommended
size is not encouraged.
Of the three court sizes above, Tennis Queensland recommends all new courts should be
constructed per the middle plan (approx. 36.6m x 18.3m) which is the ITF recommended
full size court dimensions. As previously state, this size will allow for professional and
elite junior tournament play as well as provide maximum social and competition player
enjoyment and minimise the risk of potential litigation.
Technical Manual 22
4.5.2 Court separation
The ITF rules are silent on separation of courts where no dividing fence exists (banked
courts). Tennis Australia has published a standard for separation of unfenced banked
courts. This recommends as follows:
Technical Manual 23
Technical Manual 24
Technical Manual 25
Technical Manual 26
Technical Manual 27
4.5.3 Dividing fences
Dividing fences separate courts
where banked court arrangements
exist. The inclusion of a dividing
fence increases the size of the base
structure as the run-off from the
sideline to the fence (doubled) is
greater than the distance between
sidelines on courts without dividing
fences. This increases the total
court area and consequently the cost
of construction and maintenance.
However, dividing fences, even if low height (say 1200mm) or partial fences, improve
enjoyment of players as they contain balls on the court. They reduce the need to fetch
stray balls, and subsequently the incidence of a ball from one court disrupting play on an
adjoining court. Stray balls may also lead to trip injuries to players, and therefore presents
an additional risk factor that could lead to litigation costs.
Tennis Queensland recommends the inclusion of dividing fences on banked courts.
Further detail of court dividing fences is provided in Section 8.
4.5.4 Orientation
(NOTE: The diagram at
right is for the Northern
Hemi-sphere only and is
yet to be reproduced to
reflect Southern
Hemisphere requirements)
Court orientation is
planned to minimize glare
from a rising or setting sun
shining into players’ eyes.
Orientation is determined
to minimize this
inconvenience for the
particular
latitude/longitude of the
court taking account the
periods of the year during
which play cannot occur
during early morning due
to climatic conditions.
The optimum angle is
found by determining the
azimuth for sunrise and
sunset at the time of the
summer and winter
solstice and bisecting this
angle. This can be
complicated in areas
where play cannot occur
at early morning or late
afternoon due to climatic
conditions. However,
across Australia, play is
reasonably possible at any
time during the year.
Technical Manual 28
Therefore, the optimum alignment for a court is within a few degrees of true north,
although given our western sun causes the most discomfort for playing, courts may be
aligned a few degrees east of north to compensate for this factor. To simplify
unnecessary calculations a line of true north-south should be adopted as the ideal
orientation for tennis courts in this country.
4.6 Vegetation
Vegetation presents a risk to the tennis facility both above and below ground level.
Above ground level, vegetation can contaminate courts with droppings that discolour the
surface, damage surface material and generally make the surface uncomfortable to play
on. These contaminations may encourage the growth of algae.
In addition to this, contaminations such as pine needles, twigs, leaves etc may present a
slip hazard for players and should be avoided.
Below the surface, root systems can change moisture content leading to shrink/swell of
reactive soils that can ultimately cause cracking of asphalt or concrete surfaces. The
roots themselves also invade base structures causing heaving, cracking and other
problems.
4.7 Overland flow of water and drainage

Drainage issues are covered in greater detail in Section 5 of this manual.
4.7.1 Surface water.

In considering the impact of water on a potential tennis court site, the flow of water over
the surface and underground must be considered.
Overland flow includes water flowing from higher ground over the natural contours of the
ground, water collected from
hardstand areas and water flowing
from roofs etc.
Floodwater must also be
considered. Nearby streams may
produce flash flooding that can
inundate a court.
Problems caused by surface water
include:
• Carriage of debris onto the
court
• Silting up of synthetic grass
surfaces
• Lifting of synthetic grass
surfaces resulting in
movement of the surface
when the flooding abates.
4.7.2 Subsurface water

Subsurface moisture flow varies
the moisture content under a
court. Where the subgrade
conditions are reactive, changes in
moisture content lead to
swell/shrink of the subgrade. This
seldom applies uniformly under a
court and differential movement
occurs.
Technical Manual 29
Over a single cycle subsurface moisture changes can lead to unevenness of the surface.
Over multiple cycles, damage to the base structure can occur.
Treatment of subsurface water is a design element of the court construction. Cut-off
drains and similar treatments are recommended.
4.8 Choice of contractor

Tennis Queensland cannot make recommendations regarding the worth or otherwise of
individual tennis court builders. To do this would require a monitoring of every court
builders’ ongoing performance and resources are clearly not available to do this.
However, Tennis Queensland has sought and obtained assurances from the Sports
Constructors’ Association regarding the performance of their builder members. Tennis
Queensland has influence with this association.
While one cannot assume that builders who are not members of that association will not
provide quality of service, affiliated clubs and associations are encouraged to invite
quotes from members of the Sports Constructors Association. A list of their members is
available on the web site at www.sportscontractors.com.au
Technical Manual 30
5 Earthworks and subgrade
5.1 Introduction
Earthworks and subgrade issues are, without doubt,
the most critical considerations when constructing a
court. If a poor decision is made during the phase of
construction, the entire court may need to be
demolished for future repairs. The importance of
obtaining geotechnical advice from a qualified
engineer is repeated throughout this manual for very
good reasons. Many courts have been constructed
without appropriate regard for the existing subgrade
conditions and the result has been a disaster for
clubs.
A geotechnical engineer can test the existing ground conditions and provide advice on
how the court should be constructed. There are no shortcuts in this phase of
construction.

Base That part of the court structure on which the playing surface is
applied. Typically, this may be a concrete slab or an asphalt
pavement inclusive of the ‘roadbase’ structure on which the asphalt
is applied.
Batter The method of retaining an earth structure that involves
compacting fill (or the embankment at the end of an excavation)
and tapering it away to natural ground. This is generally preferred
for relatively low depths of cut for reasons of economics when
compared to retaining walls.
Buried waste Material that has been disposed of on site and covered with earth.
Buried waste may include broken bricks or concrete, car bodies,
vegetable matter, etc.
Cut off drains Trenches of granular material, usually including slotted drainage
drainage points.
Cut/fill The act of cutting material from the high side of a slope and placing
it in compacted layers at the low side to create a level platform.
Deleterious Material that may cause future problems for construction, such as
material vegetation that may rot away, etc.
Geotechnical A Specialist Engineer qualified to measure, analyse and provide
Engineer advice on matters pertaining to soil conditions. Typically, this
expert may have a Civil Engineering background.
Ground slip Unstable ground at or near the edge of an embankment that may
give way due to climatic or other influences.
Optimum moisture A measure of the moisture content in the compactable material at
content which maximum compaction occurs.
Overland flow of Water flowing across the surface of the ground caused by rain etc.
water This may be greater than expected where rainfall is collected by
large impervious areas such as car parks and roofs of structures.
Piles One of a number of posts driven (or poured) into the ground on
which a structure is constructed.
Plastic Able to be moulded or shaped.
Technical Manual 31
Reactivity The property of soil that causes it to swell when moisture content
designed court.
Sight screen A screen erected (or foliage grown) to provide an even background
that prevents interference in sighting the moving tennis ball.
Subgrade Describes the earth structure underneath the court base.
Underground flow Water seeping underground that may penetrate the court precinct.
of water
5.3 Site investigation

The site investigation involves an examination of all site issues that must be considered
before construction is planned. Examples of issues may include but not be limited to:
• Overland flow of storm water, underground flow, etc.
• Condition of subgrade, including soil reactivity, existence of fill, buried waste,
potential ground slip, etc.
• Existing services under or over the site including power, water, sewerage,
stormwater, telecommunications, etc.
• Vegetation, including buried tree roots from previous clearing activities
• Slope, cut/fill requirements,
• Access for construction machinery
• Existing and future urban or infrastructure development at or near the site could
potentially affect or be affected by the courts, lighting, traffic, etc.
5.4 Soil report

No major construction should ever be considered without first obtaining a site report from
a geotechnical engineer. The site report determines the stability of the site and allows
sound engineering decisions to be made on the design of the court base and other
structures. Tennis Queensland Technical Services Committee recommends a soil report
for all activities.
5.5 Underground flow of water and drainage

Underground flow of water refers to seepage across a court site that is difficult to detect
but affects the moisture content in the subgrade. Changes in moisture content in the
subgrade is important as it can lead to expansion/contraction of the soil under the base
and ultimately lead to base cracking and court failure.
The changes in moisture content are most damaging. If moisture existing under a
platform is stable then shrink/swell does not occur.
Treatment for underground flow of water will usually involve cut off drains of sufficient
depth to intercept the moisture flow and carry it away. Alternatively, vertical walls are
constructed underground to prevent moisture change under the court.
Surface drainage is equally important. Flow of water across the surface of a court may
limit play in wet conditions at a minimum and carry debris on to a court at worst.
Surfaces such as synthetic grass are susceptible to pollutants such as silt.
5.6 Compaction
Compaction refers to the process of placing earth in a manner that causes it to behave
like natural ground over time and given variable environmental conditions. The most
frequent situation when compaction forms a major part of the construction process is “cut-
to-fill” sites where earth is removed from the high side/end of the court area and placed at
the low side/end to create a level platform. Another situation is where trees or other
Technical Manual 32
deleterious material is removed from the court subgrade. In these situations the earth
placed in the void must be compacted to ensure ground conditions match the natural
ground.
When a void is filled under the supervision of an engineer or other suitably qualified
person the filled area will be built up in layers with each layer compacted as it is placed.
The thickness (depth) of each of these layers will depend on the type of compaction
equipment used. Generally, the layers will be limited to 150mm thick although there are
types of equipment, such as impact rollers, that can compact thicker depths. If lighter
equipment is used, such as a vibrating plate or pedestrian roller, the layers may be
limited to 100mm or less.
Another important element of compaction is moisture content of the fill material. Each
different type of material will have its own optimum moisture content. This moisture
content provides the lubrication that permits particles to pack together tightly. However, if
the moisture content is too high the material will become too plastic and compaction will
be impossible.
If a site has been filled without appropriate supervision it is described as “uncontrolled
fill”. An example of this may occur when a gully is filled and handed over to a sporting
body to use as a sports site. There has been many a former tip given to a sporting club
for development.
Where fill is uncontrolled, several options are available. Small depths of fill may be
excavated and refilled in layers with appropriate compaction methods. A geotechnical
engineer may recommend the use of an impact roller as a suitable treatment.
Alternatively, construction techniques may require poured or driven piles, beams,
platforms of compactable material etc. These decisions can only be made by a qualified
engineer following appropriate testing of the ground.
If the site is being converted into a football field or parkland this may be satisfactory as
surface levels can be adjusted at a later time with the importation of additional fill or
topsoil to re-establish levels. However, if a concrete or asphalt structure is constructed,
and subsequent ground movement occurs, the sporting facility may need to be
demolished. This is a major problem for sports such as tennis, netball, basketball etc. It
may be better to reject such a site rather than attempt to construct a facility on uncertain
ground. Where the site does have uncontrolled fill, the cost of constructing a facility may
be uneconomic.
5.7 Retaining
5.7.1 Types of walls

As a general rule, if any form of construction
(from tennis courts to buildings) can be
undertaken without the need for retaining walls,
than this will always be the best way to go.
However, there will be instances such as
extremes of natural topography or space
restrictions, where retaining walls will be
required.
There is a wide variety - in terms of structural capacity, cost and appearance - of retaining
wall systems available. What may be perfect for one site might be completely
inappropriate for another. The choice may be dictated by purpose, soil conditions,
retaining wall height, available working space, cost and aesthetics. Simple retaining walls
less than 600mm high do not generally require major structural design input, however
walls of greater height should be designed by a certified Civil or Structural Engineer.
What most people fail to understand is that not only is a retaining wall holding back earth,
it is also holding back the flow of sub-surface water, which is more dynamic and
potentially more destructive. All retaining walls should have a drainage system behind
them unless the wall is specifically designed to allow for water to pass through this wall
Technical Manual 33
and be collected via spoon or surface drains on the exposed side. These drainage
systems are vital to relieve soil movement and the pressures generated by the presence
of water. This system is also needed to remove these waters from either under the court
or to prevent them from soaking into soils adjacent to the court.
Of equal importance is the waterproofing to the rear face of the wall if the front side of the
wall is to be exposed to view. Water which seeps through the concrete carries with it
chemicals from the concrete that will discolour the wall. In addition to traditional bitumen
or polyurethane based membranes applied to these walls, there is also a water
impermeable rolled material that has little tunnels of vertical drain lines protected by a
filter fabric (so they don’t clog up) which works exceedingly well.
A retaining wall (excluding natural stone/rock or any specially faced products) that is
exposed to the court should be painted, normally the same colour as the inner playing
surface colour, so it looks like it belongs there and it is a part of the court.
A correctly designed and constructed retaining wall that is regularly monitored should
present few problems and relatively minimal on-going maintenance costs. Retaining walls
that have been inadequately designed or constructed poorly generally do not take long to
show signs of inadequacy or even impending failure. Typically, these failures are due to:
• underestimation of the size and strength of the footings required to support
and/or anchor this wall into the ground (where footings are required)
• insufficient ties between these footings and the wall structure itself, resulting in
failures at this point
• inadequate or poorly installed (and in some cases, the complete lack of) drainage
lines and associated backfill materials behind these walls
• incorrectly selected or applied waterproofing membranes to the rear of these
walls as discussed above
• undersized wall thickness or incorrect materials selection to be capable of holding
back the volume of earth material being retained
• poor construction practices and/or
incompetent supervision of
construction works
Some examples of commonly used retaining
wall types include:
• boulders or rocks (with or without
mortar infilling)
• timber or pre-cast concrete sleepers
• brickwork
• concrete blockwork
• proprietary brand “link block” or
“keystone” concrete block products
(e.g. Hanson, Boral, etc)
• pre-cast concrete crib walls
• cast in-situ concrete
• ground or rock anchor system with
sprayed concrete
Technical Manual 34
Technical Manual 35
Technical Manual 36
Technical Manual 37
5.8 Site maintenance
5.8.1 Control of vegetation

Vegetation can cause major problems for tennis court structures. While they may be
aesthetically pleasing, provide shade for spectators and can act as a sight screen or wind
break, tree roots can cause significant damage to the court base.
Tree roots are attracted to the court base as the moisture content below the court is
maintained at a higher rate than surrounding ground as evaporation is limited.
When tree roots penetrate the court subgrade they increase in size and provide upward
pressure under the court base. Tree roots can be observed under an asphalt court as
irregular cracks radiating from the tree. Concrete courts are also lifted and crack under
the differential pressures resulting from the upward pressure of the tree root and the
voids either side. Often, this leads to a trip hazard occurring along the line of the
construction joint, saw cut joint, etc.
The planting of nearby trees should be avoided where the root system can reach the
court platform. Each variety has a reasonably predictable root distance. This information
is available from appropriately qualified persons.
Technical Manual 38
6 Base construction
6.1 Introduction
Asphalt batching Manufacturing facility at which asphalt is produced prior to delivery

plant to site and laying.
Asphaltic cement Manufactured asphalt product used for the wearing surfaces on
(AC) tennis courts, car parks, roadways etc. Often referred to as
“bitumen”.
Bedding sand Graded river sand placed under a concrete slab.
Bobcat Small to medium sized (skid-steer) machine used in earthmoving.
Cement stabilized A process where cement is mixed with earth material in smaller
quantities to provide greater binding power and hence strength.
Cementitous fillers. Rigid fillers used for repairs to hard surfaces such as asphalt or
concrete. These are usually cement based.
Elastomeric Flexible polymer based fillers used to repair asphalt or concrete
(flexible) fillers that allows some movement without breaking out.
Cold joints Term used in asphalt construction to describe the joins between
successive passes of the asphalt laying machine where adhesion
between the rows is unsatisfactory. In concrete construction, it
describes the joins between separate batches of concrete where
adhesion is incomplete.
Compressive The strength of a product to resist construction by compression.
strength
Construction film Often called “builders’ film” or “visqueen”, this plastic film is
delivered in rolls and used to provide a barrier between concrete
being placed and the earth below.
Construction joints Joints intentionally placed in a concrete slab to localize cracking
caused by concrete shrinkage during curing.
Crack control joints Refer to “construction joints” above.
Crusher dust Sand sized particles that are a by-product of crushing rock.
Curing The process during which concrete undergoes the chemical
reaction causing it to harden and achieve full strength.
Curing agents Chemical agents that control the curing process of concrete to
increase the strength of the slab.
Defects liability Period during which the constructor is responsible for failure.
period
De-lamination Failure of a product that results in it flaking off in layers.
Dowel joints A form of construction joint in which a number of steel rods or
“dowels” are used to connect two separate slabs. One end of the
dowel is usually cast in the first slab and the other end greased or
placed in a sheath to allow it to slip in and out of the other portion
of the slab. The function of the dowel is to allow horizontal
movement but prevent vertical movement of the two sections of
slab that may produce a slip hazard.
Edge beam A rigid beam, usually reinforced concrete providing strength to the
Technical Manual 39
edge of an asphalt or concrete slab.
Elastomeric Flexible. Used to describe flexible fillers.
Plane The description of the surface indicating that it is not bowed, or
humped.
Falls A measure of the slope of the surface.
Boxing (formwork) Removable former used to contain concrete until it has hardened.
Granular layer Layer of base material under asphalt formed by compacting
granular material such as crushed rock that provides the strength
of the base.
Helicopter Mechanical trowel used to achieve planarity in a concrete slab, so
named because of the rotating blades.
Light broom” finish A method of achieving a finely textured finish on concrete by lightly
drawing a fine broom across the surface as the concrete is
hardening.
Pavers or Paving Machine used to place asphalt that includes rollers.
machine
Ponding In a finished court this refers to defects in the surface in which
water lies rather than draining away. In concrete curing, it refers to
the intentional creation of dams to trap water over the surface and
slow the curing process.
Portland cement Pure cement, without additives.
Post stressing A form of concrete slab construction in which conduits or pipes are
placed in the slab during the pour and high tensile cables are
strained immediately afterwards to provide strength to the slab.
Prime coat In asphalting, this refers to a bituminous material spayed on to the
crushed rock base that penetrates the base prior to chemically
changing to act as a binding agent.
Proprietary Describes any system used in construction where the installer has
systems exclusive rights to its use.
Reinforced Often described as “pre tensioned”. Reinforcing steel is placed
concrete prior to the concrete to provide tensile strength to the slab.
Roadbase Crushed rock material where different sized material is prepared in
a manner that maximizes compacted strength.
Shrinkage cracks Cracks appearing in concrete during curing that are caused by the
natural shrinking action.
Smooth drum Roller used for compacting materials that uses a smooth drum that
vibrating roller is mechanically vibrated to increase compaction.
“Soffcut” joints Joints cut into concrete as soon as the slab can support foot traffic.
These joints are usually 3mm wide and 25mm deep and provide an
intentionally ‘weak’ point where shrinkage cracking will occur in a
controlled way.
Tensile strength Strength of a product to withstand being ‘pulled apart’.
Tramlines Doubles lines on the court line marking.
Viscosity Density of a liquid, measured by the ability of a material to flow
through an aperture at a particular rate.
Technical Manual 40
6.3 Choice of base to suit site conditions, surface choice
The court base is one of the most important elements of the tennis court structure.
Failure of the court base renders the court unplayable. Rectification of court base failure
may require dismantling of other elements (surface, fencing, lighting, etc) and can cost
more than the initial construction cost of the court. Choice of base type is therefore very
important and needs to be taken after appropriate investigation and professional support.
Different construction techniques can be used for the base structure. These include:
• Reinforced concrete (pre-tensioned or post-tensioned)
• Asphalt
• Compacted earth (includes decomposed granite, roadbase, crushed rock,
cement stabilized, etc).
• Proprietary systems (including chemical treatments)
A number of issues need consideration when choosing base construction method.
Firstly, different bases are required for different surfaces. For example, an acrylic surface
can only be applied to an asphalt or concrete base. Synthetic grass may be installed
over asphalt, concrete or many of the compacted earth and proprietary systems. Please
refer to Section 7.1.3 regarding choice of surface.
Secondly, the base structure is very much dependant on the site conditions. For
example, a concrete base designed for one site may fail if constructed on a different site.
Section 6 provides advice on this and the importance of designing to suit site conditions
cannot be over emphasized.
It should also be noted that appropriate design of the base structure can deliver real
savings to a club or association.
6.4 Elements common to all bases.

Appropriate site preparation is essential for all base types. Refer to section 5 for further
details.
Subgrade preparation includes establishment of appropriate falls that will be carried
through to the finished surface.
6.5 Asphalt bases

As with all surfaces, asphalt has advantages and disadvantages. Asphalt can be
cheaper than alternatives where the product is available in reasonable geographic
proximity. Asphalt leaves the asphalt batching plant hot and must be delivered to site
above a threshold temperature. For this reason, it is only suitable for use on sites located
within a reasonable distance from the asphalt batching plant. Its primary use as a road
surface means that asphalt batching plants are widely spread across the more densely
populated areas of the country.
6.5.1 Elements of an asphalt base

The asphalt base consists of at least two elements.
The first is the structural layer, termed the “granular
layer”, which consists of a base of crushed rock of at
least 150mm in thickness which is covered by a layer
of asphalt (more correctly described as “asphaltic
cement” or “AC”), usually about 25mm in thickness.
The strength of the structure is provided by the
crushed rock in the granular layer. The asphalt
provides a smooth surface for confident footing and
sound ball bounce, as well as a moisture barrier to protect the crushed rock base from
erosion and water penetration. The asphalt does not provide strength.
Asphalt is sometimes described as a “flexible” base as it will allow some ground
movement without failure. Asphalt, like other base structures, has a finite life span. Over
Technical Manual 41
time, it loses the oils and other chemicals that bind it together and it becomes brittle.
Cracks appear and the surface may become pitted and uneven. Application of an acrylic
surface, or covering with synthetic grass and similar products, will prolong the life of the
asphalt. In many cases asphalt can be repaired with the use of cementitous or
elastomeric (flexible) fillers.
The granular layer of crushed
rock or “roadbase” material is a
blend of crushed rock of different
particle sizes, each with an
angular shape that assist it to
bind together when compacted.
This forms a strong and mostly
rigid structure.
During construction, the crushed
rock is spread out using a small
grader, bobcat or similar
machine and then rolled with a
smooth drum roller. The roller
has a vibrating action to increase compaction. The moisture content of the crushed rock
is a critical element of the process and this is maintained throughout the process to close
tolerances to achieve maximum compaction and particle bind. The finished sub base will
be constructed to very close tolerances of fall and plane.
A “prime coat” of a bituminous or polymer
material is sprayed over the granular layer
prior to the installation of the asphalt and
allowed to cure. The prime coat is designed to
bind the granular material to preserve its
integrity, reduce permeability, stabilize
moisture and, most importantly, provide a bond
between the granular layer and the asphalt.
When sprayed on to the roadbase, the prime
coat undergoes a chemical reaction (called
“cracking”) where it loses the viscosity that
allows it to soak into the surface, and becomes
thicker, binding the surface together. An unsatisfactory alternative to the prime coat is a
“tack” coat. Although cheaper, tack coating is not recommended as the tack coat has
lesser properties of binding and sealing the base material.
The asphalt is then applied to the crushed rock base with a self-propelled asphalt laying
machine or “paver” that places and rolls the asphalt in strips that equate to the width of
the paving machine (usually 2 – 3m wide depending on the machine used). The paving
machine tightly controls the plane tolerance of the finished surface. The machine
operator takes great care to ensure the joins between the strips are essentially negligible.
An important aspect of asphalt laying is the temperature of the asphalt material when it is
placed and compacted. This is dependent on the type of machinery used in rolling. For
example, a particular type of asphalt compacted with a steel drum roller may need to be
between 100 degrees Celsius and 160 degrees Celsius degrees at time of rolling.
6.5.2 Construction process

The assumption has been made that the site has already been prepared as described in
Section 4 of this Manual.
The granular material is transported to site and laid in accordance with the technical
specification. Important aspects include the particle size, size distribution, particle shape,
moisture content and placement. Placement involves spreading and compaction as well
as surface profile when completed. The final court profile will be established during this
phase (refer to the stated “surface tolerance” required for each court type as detailed in
Section 7 of this Manual).
Technical Manual 42
A concrete edge beam is placed around the perimeter of the granular material, set
accurately to the height of the finished asphalt surface. In addition to providing a strong
and stable edge to the court, the edge beam allows the asphalt to be compacted right up
to the edge without the edge collapsing or flaking.
The granular material is prime-coated with an appropriate bituminous primer. This is a
chemical process and is temperature dependant.
Primer application rates are important and
should be approximately 1lt per m2. It is also
important to prevent damage to the installed
primer due to traffic, including the paving
machine and workers.
Finally the asphalt is placed using an asphalt
paving machine. Generally, the asphalt
specification is AC5 – AC7 (denoting 5mm or
7mm maximum particle size) and laid to a
thickness of 25mm.
The temperature at time of installation is a critical
issue. For example, a particular type of asphalt
may need to be spread at approximately 150deg
Celsius and compacted at temperatures above
90deg Celsius subject to placement method.
The asphalt should be discharged from the
delivery vehicles directly into the hopper of the
paving machine and spread and compacted in a
continuous process. The surface is then
compacted using a vibrating smooth drum roller
to achieve the required density and plane.
6.5.3 Construction failures.

Practices that can cause failures during construction include:
• Insufficient subgrade compaction. Where the subgrade is not compacted,
attempts to compact the crushed rock base will fail.
• Vegetation, soft spots or other deleterious conditions of the subgrade. Decaying
vegetation such as grasses or roots will cause subsidence of the subgrade
creating voids under the crushed rock base. Over time, the crushed rock will
subside into these voids leading to a collapse of the surface.
• Inadequate compaction of the granular material. This can lead to settlement over
time creating ponding, cracking and other surface defects.
• Incorrect specification of granular material leading to compaction problems, poor
bonding, uneven surface, etc.
• Prime coat poorly applied or damaged after
installation. This can lead to de-lamination of
the surface, base failure, etc.
• Inadequate compaction of the asphalt layer,
resulting in erosion of the asphalt over time.
• Asphalt delivered too cold or allowed to cool
before installation. This creates de-
lamination and similar problems.
• Cold joints between runs of the paving
machine. These appear as cracks over time and create an uneven surface, allow
water penetration into the base and subgrade, etc.
Technical Manual 43
6.5.4 Deterioration failures.
The following issues contribute to failure over time
• Movement of the subgrade caused by inadequate compaction, changes in
moisture content, etc. This is described above.
• Loss of oils and binders over time. This is the natural aging of the asphalt
surface due to exposure to the elements. The result is erosion of the surface and
resulting unevenness. Regular maintenance and coating with a quality acrylic
surface will slow down the aging process.
• Ingress of tree roots or other vegetation leads to uneven surfaces, cracking with
resulting water penetration, etc. This is preventable with attention to
maintenance of court surrounds.
• Seasonal variation of moisture content,
particularly surrounding the edges of the
base. Seasonal movement extends
several metres into the court and results in
cracks appearing parallel to the court
fence, usually about 2m in. There are a
number of methods available to control
this including pathways around the court,
vertical barrier wall under the ground level,
control of moisture levels through regular
watering, etc.
• Inadequate attention to surface maintenance, such as failure to fill cracks when
they appear to prevent water ingress, etc. This is a preventable risk.
6.5.5 Measures of quality.

At the time of construction, the quality of the base is measured by surface tolerances
such as falls and planarity, porosity/density of the asphalt, strength of the court edges,
absence of cold joints where the paving machine passed, etc. Twelve (12) months is
considered to be an appropriate defects liability period for asphalt court bases.
6.6 Concrete bases

A well constructed concrete base built to a specification suitable for site conditions will
provide the longest service life of all base types listed in this manual. The important
words in this generalization are “well constructed” and “specified for site conditions”. A
concrete base built to an inadequate specification for the particular site will fail and failure
of a concrete base carries a heavy financial penalty.
As with other base types, concrete also requires ongoing maintenance, particularly the
construction joints and court surrounds. Failure to adhere to a maintenance plan can
destroy an otherwise soundly constructed base.
Concrete has very high compressive strength and low tensile strength. The tensile
strength of a concrete court base is provided by the reinforcing. Concrete has minimal
flexibility and copes with ground movement by bridging low areas.
Curing occurs in the first days or weeks after the concrete is laid. During this time
shrinkage occurs and strength increases. The strength of the concrete is increased by
slowing down the curing process.
During curing shrinkage cracks appear. This is normal; however, sound construction
techniques minimize and control this cracking to ensure it does not affect the strength or
aesthetics of the finished slab.
6.6.1 Types of concrete bases

The most familiar concrete base is the reinforced concrete slab used for tennis courts,
house slabs and driveways. The shape of the slab is set out with boxing, the steel
Technical Manual 44
reinforcing mesh is placed and the concrete is poured over this and vibrated / screeded /
towelled to achieve the finished surface. Less familiar is post-tensioning, where the
reinforcing steel is drawn through conduits and tensioned after the slab is poured. Each
has advantages and disadvantages.
Other methods of increasing the tensile strength of concrete have been developed,
however, to date; none have proven as successful as the traditional methods above.
These will be added to this manual in future as their value for tennis court construction is
proven.
Concrete is manufactured to various values of strength according to the demands of the
job. Strength is specified in the SI units “Mega Pascals” or “MPa”. Concrete may be
ordered at 20MPa, 25MPa, 32MPa, etc. and this describes the strength it will achieve
after curing.
When constructing a tennis court that will have an Acrylic surface, consideration must
also be given to the use of additives. Additives are included during manufacture to
strengthen the mix, reduce cost, improve surface finish, etc. However, some of these
additives react negatively with the acrylic surface material. As a general rule, acrylic
surfaces require Portland Cement free of additives for a quality finish. This should be
checked with the acrylic surface provider before concrete is ordered.
6.6.2 Reinforced concrete bases

“Reinforced Concrete Bases” refer to the most familiar type of base, commonly used for
house slabs and driveways. They consist of a layer of concrete of appropriate thickness
reinforced with steel mesh. The science of this is interesting for some.
Concrete has very high
compressive strength. That
is, it can withstand very high
loads without crumbling.
However, concrete has very
low tensile strength. This
means it will crack easily.
Steel, however, has very
high tensile strength.
When combined in a slab,
the concrete provides the
compressive strength and
the steel provides the tensile
strength. The specification
for the slab contains many
important dimensions to
ensure these two work
together to achieve the
strength required for the site
conditions. These
dimensions include strength
of concrete in MPa,
thickness of concrete,
thickness of the steel mesh,
tensile strength of the steel
used to construct the mesh,
placement of the mesh in
the slab relative to the top
and bottom of the slab, etc.
The importance of these
design parameters cannot
be overstated. To over-
specify is to waste money.
Technical Manual 45
To under-specify is to risk failure, which will waste much more money.
6.6.3 Construction
Site preparation is carried out in accordance with principles outlined in section 4 above.
Bedding sand is placed over the subgrade. The bedding sand performs a number of
important purposes including levelling the base, permitting moisture under the slab to
escape, allowing some movement of the slab during curing and at other times when
ground movement occurs, etc. An adequate coverage of bedding sand is necessary to
achieve this successfully, usually 50mm.
The bedding sand is covered with construction film, which is overlapped and taped at the
joints. This film also serves a number of purposes including slowing the loss of moisture
during curing, control of moisture ingress at other times, facilitating slippage during
curing, etc.
During construction, the site is set out and
boxing (formwork) is placed around the
perimeter to contain the concrete at time of
the pour. The boxing is often set to finished
slab height, although this is not always the
case where the builder may set the boxing
above finished slab height and control the
finished levels using laser levelling
equipment.
The steel mesh is placed over the
construction film in sheets, each sheet
overlapped by one square (200mm) and tied
with tie wire. The placement of the mesh on appropriate height bar chairs is an essential
as the physical principles of concrete slabs, in particular the compressive strength of
concrete and the tensile strength of steel, work together to achieve a successful base.
At this time the base is ready for placement of the concrete. The use of curing agents
and other additives is not recommended where an acrylic surface is to be installed.
These can contribute to poor adhesion of the acrylic surface, resulting in bubbling and
peeling. Refer to section 7.1.5.1 “Acrylic Surfaces” for further information.
Concrete is delivered in batches of (usually)
approximately 6m3. The timing of the delivery
should, ideally, suit the ability of the construction
team to properly place the concrete. A larger
team will be able to place the concrete faster
than a small team. A team of about 10 workers
is considered necessary to adequately place and
finish the concrete to achieve the tolerances
required. Some of these workers will be
spreading the concrete, others will be setting
levels using laser equipment, and other workers
will be screeding to achieve the finished surface.
Finally, workers will be engaged on “bull floats”
and “helicopters” achieving the close tolerances
necessary for a tennis court surface.
When placed, the concrete will quickly
commence curing. Curing is a chemical process
where the concrete sets hard and dries out.
Because it is a chemical process, heat is
generated. As concrete cures it shrinks. This
leads to cracking of the base. Although cracking
cannot be prevented, it can be controlled to
minimize the impact.
Technical Manual 46
Slowing down the curing process is one way of minimizing cracking. This is achieved by
maintaining a high moisture content, thereby reducing the curing temperature. Methods
to achieve this include covering or ponding. Covering usually involves covering with
builders’ film, taped at the joints, so that moisture is trapped on the surface. Alternatively,
where a synthetic grass court is being constructed, the synthetic grass is installed
immediately after the slab is constructed (within 24 hours) and the synthetic grass plays
the same role as the builders’ film. The second method, ponding, involves continuous
wetting with hoses or sprinklers or the establishment of bund walls around the edge of the
surface and flooding with water. As curing occurs over the first seven to fourteen days,
the method used must be maintained for this period.
Another method of controlling cracking is to allow cracking to occur in places you wish it
to occur. This is generally done in addition to the methods described above as, despite
the best of efforts, shrinkage and the resultant cracks will occur. When cracking occurs
where you wish it to occur, in straight lines for example, it can be treated to remove
negative effects. Treatment of construction joints involves sealing with an appropriate
elastomeric filler to enable movement to occur but
prevent the entry of water that may seep into the
subgrade and cause swelling and future base
problems.
Crack control is achieved in the following ways.
A “construction joint” is established across the court at
the net line. Proprietary metal formers are available for
this purpose, per the figure shown to the right.
Alternatively, “dowel joints” can be established. The
construction joint divides the court into two separate
halves.
In addition to this, “soffcut” joints
are installed as soon as the slab
has cured sufficiently to allow
workers to walk on it. This is
usually three or four hours after
the concrete has been placed.
Soffcut joints should always be
installed on the day the concrete
is placed. If installed later than
this, curing shrinkage will have
reached a point where the
cracking will have commenced
and the soffcut joints will be of
little value.
Soffcut joints are always placed
in the same positions on tennis
courts. These are across the
court at the base and service
lines and along the length of the
court at the centre line and
inside tramlines (see the layout
Figure shown at right). Soffcut
joints are typically 3mm wide
and 25mm deep. In preparation
for the soffcut joints, the steel
mesh is prepared prior to the
placement. Every second bar in
the steel mesh is cut on the line
of the soffcut joint to encourage
cracking in this area.
Technical Manual 47
As mentioned above, crack control joints (Construction Joints and Soffcut Joints) are an
essential element of concrete slab construction and should not be omitted. Following
curing, usually after four weeks, these are treated with an elastomeric filler to prevent
moisture entry. This is also an important component of concrete slab construction.
Finishing of the concrete slab is an important element. For acrylic surfaces, a “light
broom” finish is achieved by dragging a light broom across the court after the helicopter
trowel has been used. This aids adhesion of
the acrylic primer coat (see also, Acrylic
Surfaces in section 7.2). The standard of
trowel finish is less critical for synthetic grass
surfaces.
Where acrylic surfaces are applied to
concrete surfaces a minimum curing time of
four weeks is recommended. This allows the
moisture content to reach an appropriate
level and also enables chemicals to leach
out of the concrete slab.
6.6.4 Post Stressed concrete bases

Post stressing is a design that is used often in major building construction but relatively
seldom used in tennis court construction in Australia. The benefits of post-stressing are
only now becoming known to the tennis court construction industry and the future will see
this construction method applied more widely where it delivers a cost effective solution to
construction in particularly adverse site and/or soil conditions.
In post tensioned courts the steel reinforcing is added immediately after the concrete slab
is placed rather than before. During placement of the concrete, conduits are installed in
the slab running across the court and along the length of the court. Immediately after
placement of the concrete, tensile steel cables are drawn through the concretes and
tightened up using clamping devices at each end. This pulls the slab together under
tension during curing. Rather than shrinking from the centre to the edge, as is the case
with traditional reinforced concrete courts, the slab shrinks from the edge into the centre.
Crack control joints are not required with post-tensioned construction techniques.
However, where multiple courts are constructed using post-tensioning techniques,
appropriate separation of the courts using construction joints may be required.
The figure on the following page illustrates typical post-tensioned court slab details.
Technical Manual 48
Technical Manual 49
6.7 Compacted earth base
Synthetic grass surfaces have traditionally been laid over compacted earth bases. This
construction technique can be used effectively and has the advantages of reduced cost.
In some cases, the flexibility of the base has benefits where small amounts of ground
movement occur.
Different court builders have developed different techniques for constructing compacted
earth bases. Most popular is construction using compacted crushed rock or “roadbase”
material. Others claim success with “crusher dust”, decomposed granite, chemically
stabilised systems, etc. Chemically stabilized systems are treated below in Section 6.8.1.
The material chosen by the court builder will have basic properties of compatibility,
strength and stability over time. A material such as roadbase achieves this through the
choice of rock particles that have high compressive strength, particle shape that enables
them to bind together, particle size that allows the voids to fill and bind, and low clay
content to ensure they are essentially unaffected by changes in moisture content.
Roadbase material is specified in these terms
and is produced, primarily, for construction of
carriageways that will ultimately be covered with
asphalt to provide a wearing surface and control
moisture entry. In synthetic grass tennis court
application, the sand filled artificial grass (SFAG)
fulfils this purpose.
The roadbase material is spread using a bobcat
or similar machine and trimmed using a levelling
machine guided by a rotating laser beam. Very
fine tolerances of surface planarity and fall can
be achieved in this way.
The roadbase material is placed over the
prepared subgrade in layers and compacted
using a smooth drum vibrating roller. Moisture
content of the roadbase during construction is
important as it must be sufficient to provide the
lubrication for particles to move and bind but not
so great as to cause it to “glug” or soften. A
roadbase court construction may include a
different specification for the final few millimetres
to achieve a surface free from voids that could
cause unevenness in the finished playing
surface.
A recent development in cushion acrylic surfaces permits an acrylic surface to be placed
on a specially prepared proprietary court base engineered in a manner similar to but not
the same as a compacted roadbase court base. This construction technique is in early
stages of development in Australia.
An alternative to the compacted roadbase court base is the use of decomposed granite.
Caution must be exercised in choosing this surface as the high clay content of
decomposed granite can cause reactivity or softening with changes to moisture content.
This may render the court unplayable for periods following heavy rain else run the risk of
damage to the court base. Attempts have been made to address this with the addition of
1% cement binder, tyned into the surface. The tyning process mixes the cement with the
top surface which is then laser levelled and rolled to create the planarity and falls
required. This is not considered to have the strength of a roadbase court base and is
more appropriate to cost effective conversion of an existing decomposed granite court
than a construction alternative for new courts. This method of conversion should be
approached with caution.
Technical Manual 50
Clay and decomposed granite court surfaces may be considered in this section of base
construction as the base and surface form a single unit. However, these will be dealt with
in the “Court Surfaces” discussions in Section 7 of this Manual.
6.8 Proprietary base systems
6.8.1 Chemically bound systems

A number of court construction companies offer chemically bound compacted earth base
structures. The base is usually constructed of imported material such as roadbase or
crusher dust that is placed and compacted in the usual way. Occasionally sand is used.
The base is then sprayed with a chemical binder. The manufacturers claim the binder
strengthens the base while permitting moisture to drain vertically through the base
resulting in the synthetic grass surface drying out more quickly. One concern with this is
that the moisture must then enter the subgrade and, should the court be built on reactive
ground, could cause subgrade problems.
The strength of this base is still derived from the compacted material over which the
spray is applied and the principles of sound compacted earth base construction must still
be adhered to. This method of construction is not recommended for difficult ground
conditions and caution is recommended if choosing this base construction method.
6.9 Maintenance and repair of base structure

A regular, structured maintenance regime covering the surface and court surrounds is the
most effective way to prolong the life of the court base. This is dealt with in Section 7 of
this manual.

A number of Australian Standards exist that cover Asphalt and Concrete platform
construction and maintenance. The principles apply equally to tennis courts. This
includes:
• Australian Standards AS 2870 and AS 3798
• CSIRO Guides, such as “Foundation Maintenance and Footing Performance: A
Homeowner’s Guide”
• Australian Asphalt Paving Association Codes of Practice.
Acrylic surface manufacturers also publish technical information on court base
construction suitable for their products.
The best method of obtaining correct information when designing a court base is via a
qualified geotechnical engineer. A geotechnical engineer will test the subgrade
conditions at the site and design a base structure that will provide the balance between
economical construction and requirements due to potential ground movement.
Throughout this manual, court owners will be encouraged to engage professional
engineering assistance at the planning stage of court construction.
Technical Manual 51
7 Surface
7.1 Introduction
7.1.1 Definitions used in this section

Acrylic Material used for surfacing courts that provides colour and texture
to the court surface.
Bird baths Depressions in the court surface that retain water following rain
Clean sweep Brand name of popular court grooming device consisting of a mat
like structure that is dragged across the court. The device gathers
leaves and other debris that can be disposed of away from the
playing surface. The “Clean Sweep” also re-distributes the infill
sand evenly across a synthetic grass surface.
Cushion acrylic Acrylic surface that includes cushion properties.
Expansion joints Construction joint that permits expansion/contraction of the court
base.
“Mat lay” systems Cushion surface installed by rolling out preformed sheet cushion
material that is jointed and coated with an acrylic surface.
Mud cracking Multiple cracks in a surface that resemble dried mud.
Pace A measurement of court characteristics that describes the speed
and departure angle of the ball when it strikes the court surface.
Pot life The period of time that a chemical material lasts from mixing to
application.
Rubber squeegee Device for spreading acrylic material over a court surface.
SFAG Sand Filled Artificial Grass.
Silica sand Sand made from silica that is used in synthetic grass tennis courts.
Silica is preferred due to hardness and particle shape.
Speed A measure of court characteristics. See “Pace” above.
Synthetic grass Outdoor carpet product used in tennis court surfacing, so named
because it is constructed and installed to resemble natural grass.
Tack Used to describe the behaviour of adhesives. A material with
“tack” grips the products being joined during the curing process.
Viscosity Density of a liquid, measured by the ability of a material to flow
through an aperture at a particular rate.
“Wet lay” systems Cushion acrylic surface where the cushion material is applied as a
liquid and built up in layers until the desired thickness is achieved.
Windrow A row of (acrylic) material left by the action of the applicator with
his/her squeegee.
7.1.2 Classification of surface systems

Different court surface systems produce different playing characteristics. They produce
different reactions to ball bounce and pace; provide different levels of grip to the players
feet, etc. This results in quite different styles of play between surfaces. These
differences result in different players being more successful on different surfaces.
7.1.3 Choice of surface

In addition to this, the style of play on some surfaces, such as natural clay, result in
longer rallies and the most successful players on these surfaces are those with a more
Technical Manual 52
tactical approach to the game. The Tennis Australia Player Development Committee has
recognized this and recommends certain surface types for developing players for the
international circuit. Clubs or individuals considering a surface for the development of
promising junior players should contact Tennis Australia for further advice on this matter.
Clubs or associations should consider the advantages and disadvantages of each
surface type when choosing to build or resurface their courts. The best test is to survey
member preferences and build surfaces that the members like to play on. After all, the
attraction and retention of members is the most important factor in the success of a club.
7.1.4 Advantages and disadvantages

As mentioned above, a club with a focus on developing juniors may choose clay courts
so that the tactical issues in winning rallies are developed. This comes at a price. The
cost of maintaining clay courts is high relative to alternatives and is addressed elsewhere
in this manual, in particular at Section 7.1.5.4.
The construction cost of decomposed granite courts made them attractive for some
struggling clubs. Again, the disadvantage of decomposed granite courts is the
maintenance, line marking etc. Although not as expensive as clay, decomposed granite
courts require regular grooming, watering, rolling, line marking before play etc. This is
extremely labour intensive and will test the resolve of club volunteers.
Low maintenance surfaces have been developed over a number of years. These include,
among others, acrylic and synthetic grass surfaces. These surfaces still require routine
maintenance but this is substantially less than other surfaces on the market.
A more recent development is the “artificial clay” surface. This is an outdoor carpet,
similar in design to the outdoor carpet used for synthetic grass surfaces but built to a
different specification and colour. The infill sand is also a different specification (and
colour) to the synthetic grass surface. Synthetic clay surfaces requires more frequent
grooming than acrylic or synthetic grass but advocates argue that this is more than offset
by the surface characteristics during play.
Many older players prefer synthetic grass or clay to acrylic surfaces, arguing that it is
more comfortable on the body and gentler on aging joints. If true, this is an equally sound
argument for junior play, at the cost of skill development.
Cushion acrylic surfaces are also available. These look similar to a standard acrylic
surface but have the inclusion of a cushion layer of between 3mm and 8mm providing
vertical cushion to the players. Current thinking suggests that cushion thickness of
between 3mm and 5mm provides the best surface for tennis.
Natural grass is an attractive surface to play on and has been popular in Australia over
many years. The major disadvantage of natural grass is the necessity to prepare it for
play. This may involve mowing, rolling and line marking. In addition to that, it requires
regular watering, mowing, fertilizing, treatment for weeds, etc.
A more detailed comparison of the advantages and disadvantages of the different
surfaces have not been included in this manual at this time. However, clubs are
reminded that members have preferences and this is the most important issue when
choosing a surface.
7.1.5 Maintenance issues

A primary issue in the selection of a surface is maintenance. An example of the
maintenance issues and costs follows.
7.1.5.1 Acrylic
This is probably the least intensive in maintenance effort of all the court surfaces.
The court should be kept clean and free from debris that can scratch the surface
underfoot or create a safety hazard.
Technical Manual 53
A known threat to acrylic surfaces is flying fox faeces. This sets hard on the surface and
bonds tightly to it. As the faeces dries, it hardens and curls up, stripping the acrylic
surface from the base. In some situations, where an asphalt base exists, the bond
between the faeces and the acrylic surface is so strong that the curling action can cause
de-lamination of the asphalt. In areas where flying foxes prevail, it is recommended that
regular inspections be carried out to remove flying fox faeces from the surface early.
The normal maintenance regime for the surface should consist of annual cleaning in
accordance with the manufacturer’s specification. This will typically involve spraying with
a detergent and cleaning off with a rotating head pressure spray. Commercial court
cleaning companies can perform this task on behalf of court owners.
7.1.5.2 Synthetic Grass

Maintenance of sand levels is the single most important task in achieving consistent
playing characteristics for sand filled artificial grass (SFAG). While other issues are
important to maintenance, the regularity of ball-bounce and footing are crucial to a
successful sporting surface and whether the chosen surface has been designed for grip
or for slide, it should be consistent. To this end the initial three to six month period of
maintenance is the most crucial to long term happiness with the synthetic grass.
This is most readily achieved with the use
of a broom with particular bristle stiffness
similar to that probably used by your
contractor during installation. A simple
pushing of the broom up and down the
court (best with the net put to one side) will
achieve corrections with each pass as will
occasional cross-wise brooming. If this is
repeated regularly (weekly if getting plenty
of use) until the adjustment service is due
the contractor will probably have little to do
but your court surface and the future
enjoyment of it will be the beneficiary. A
commercial centre may choose to mechanise this operation with drag brooms behind a
rider mower or similar, but such a process should always simulate hand brooming and
because of its abrasive nature and that it is more easily carried out, care should be
exercised to ensure that it is not over done creating premature wear.
This weekly chore can be reduced to monthly (again subject to court use) after the
“settling in” period and can be interspersed with the use of a “Clean Sweep”, a propriety
product ostensibly designed as a leaf sweeper, which assists in maintaining even sand
levels. In some States this action with the Clean Sweep is an accepted part of the
protocol of the game, dragging/bagging the court after each match thus leaving a pristine
surface for following players. This would be a worthy protocol to foster throughout all
Clubs and private courts in all States.
Environmental issues play a large part in the
required maintenance of SFAG, with fallout from
trees, algae growing in areas often shaded by trees,
overland flow from poor drainage and general fallout
from adjoining industry or the atmosphere. These
elements affect hardcourts, driveways, the roof of
your house and in fact most areas of the home, but
are often not noticed on the textured surface of a
SFAG court until they (the algae for instance) are
well entrenched.
Although the brooming described may create enough disturbance of the carpet pile to
inhibit various algae growths, there will come a time when it is appropriate to call in
professionals. A healthy maintenance industry exists within the tennis fraternity which
Technical Manual 54
can address all of the above provided that they always bear in mind the important issues
that make SFAG successful.
Unless the carpet has been infiltrated by foreign matter it is rarely desirable to remove all
of the sand from a SFAG surface as any areas so treated will need to go through the
“settling in” period again. Most maintenance firms should be dealing with the top few
millimetres of the surface and if removing sand with other polluted materials, care should
be taken that the original sand levels are returned. They should also ensure that the
treatments necessary on the side of a court do not assist in extending or spreading the
problem across the full width of the court. Equally, cleaning of mechanical equipment
after treatment at one address is important so that pollutants are not carried onto the next
court to be serviced.
Treatment of infected areas by use of gurney or strong water jets should be carried out
with caution so as to not remove an excess of sand which is difficult to replace
consistently. Part of the apparent success of such an operation is emphasised by the as
new “greenness” of the extra pile exposed below the top of the sand which can tend to
mask any remaining algae growth. The use of blowers, although very efficient for leaf
removal must be used with care as they too can remove some sand on each pass which
in turn reduces the pile height and in turn the life of the carpet.
Chemical treatment of SFAG for algae growth has often been handled with the use of
products such as copper sulphate or varying mixtures of pool chlorine and maintenance
firms have their own proprietary anti-algae treatments. Such chemical treatments should
only occur with the approval of the SFAG manufacturer who generally offers a seven year
warranty on his product and great care should be exercised so that the general
environment is not effected adversely.
Maintenance issues can be minimised by careful initial landscape planning through not
planting inappropriate types of trees and not too close to the court (the root systems
delight in ground conditions under SFAG) and the clearing of debris, leaf litter and any
other infiltration. Good base construction through levels which shed water quickly,
particularly in those areas shaded by trees or adjoining structures also assists in lowering
of maintenance effort as will regular disturbance through sand levelling. A plastic lawn
rake can make for hard work in clearing debris from the court but some solace may be
taken in that the tips of the pile are being teased in a manner that assists the “settling in”.
The accepted norm for falls which allow good drainage of a court surface, whether SFAG
or other non-porous synthetic surface types is 0.9% in both directions which on a
minimum ITF court size of 34.77m x 17.10m will create falls of approximately 300mm in
the length, 150mm in the width and 450mm from one corner to its diagonal opposite.
7.1.5.3 Synthetic Clay

The care of synthetic clay is similar to the care for synthetic grass above. However, the
particle size of the infill sand and the higher sand levels place some additional demands
on the court during play.
The court should be bagged between sets and benefits from being watered periodically.
Sand levels should be maintained.
7.1.5.4 Natural Clay

Whilst this type of court can be economical to install, they will require significantly more
ongoing maintenance (with associated costs) than hardcourt or artificial surfaces.
Effective maintenance of natural clay is vital if the surface is to remain aesthetically
pleasing, consistent in play, permeable to wet weather and long lasting.
Maintenance procedures are designed to ensure that:
• The playing surface is kept clean,
• The playing surface remains consistent to give a true and predictable game,
• Free drainage of surface water,
Technical Manual 55
• Looks attractive and well kept at all times.
These objectives are achieved by:
• Removal of surface plant debris and rubbish,
• Pulling a broom or drag mat over the surface between play,
• Keeping the surface moist by watering,
• Rolling periodically, especially after prolonged rain,
• Patching small wear depressions,
• Having surface damage repaired.
With clay courts, it is essential that an ongoing maintenance regime is adhered to, to
ensure the consistency of the playing surface and the longevity of the court. Inadequate
maintenance will significantly reduce the life of a clay playing surface.
By the very nature of the surface material, there is a tendency for compaction, wear and
wind erosion. Therefore, part of the ongoing maintenance regime includes the
rejuvenation of the surface by spreading new material to the affected areas, watering and
rolling it. Some of this rejuvenation can be carried out by the court owner or club
members after some initial supervision and guidance. Areas of heavy use (such as the
baseline area) may require rebuilding once or twice over the service life of the court.
Providing the court drainage and foundation layers are in good condition, the surface can
be scarified and new surface material spread, watered and rolled. Alternately, it may be
necessary to undertake remedial work on the foundation layers. Where fixed (non chalk)
lines are installed, it is probable that these lines will need to be replaced a number of
times during the life of the court.
Given the recent introduction of severe water restrictions in many parts of Queensland
and eastern Australia, the amount of watering these courts require to keep them in an
acceptable condition is now a major issue with maintaining these types of surfaces. In the
future, designated on site rainwater collection (i.e. via roof water collection) may be
necessary to ensure the viability of such courts.
Clay surfaces, as with any surface, do not last forever. They have a finite life, which is
dependent in part on their frequency of use and on how well they are maintained. In club
situations, some of these substantial ongoing costs can be reduced by volunteer workers
(if they can be found!). Along with the abovementioned periodic maintenance activities
and repair works, owners should ultimately factor in the costs of rebuilding the clay
surface every 10 to 20 years depending upon the maintenance regime employed.
Maintaining a large number of natural clay courts is best left to those with proven
experience with such surfaces. Unfortunately, there are very few people with this ability in
Australia and this should be taken into consideration prior to constructing or managing
such courts.
7.1.5.5 Decomposed Granite

Maintaining decomposed granite courts poses essentially the same issues as with clay
court surfaces as discussed above, with the only major difference being the materials
used for the final playing surface layer. To ensure the aesthetic and playability
consistency of these courts throughout their serviceable life, a reasonable quantity of the
original surfacing materials installed should be kept aside in storage for use during minor
re-surfacing and patching maintenance works.
7.1.6 Playing characteristics

The International Tennis Federation (ITF) has established a methodology for testing and
classifying tennis court surfaces. The term used to describe the difference between the
surfaces is “pace”. Laboratories accredited by the ITF carry out the testing in accordance
with the strict guidelines of the methodology.
Technical Manual 56
Test methods vary, but the current approved method of testing a court surface is to
project a ball on to the surface at a predetermined speed and angle with the amount of
spin on the ball limited to a set parameter. The angle and velocity of the rebound is
measured. This variation in rebound is caused by the friction between the court surface
and the ball, the behaviour of the surface (where deflection may occur), etc.
The test method generally uses photographic or similar equipment to track behaviour of
the ball.
The ITF Surface Pace Rating is calculated using a formula that takes account of the
velocity and angle of the ball before and after it strikes the surface.
An alternative surface test is to measure the Slip Resistance”. A number of machines are
commercially available for measuring slip resistance of pavements and these are often
adapted for use on tennis courts. This method is not appropriate for all court surfaces.
For example, some testing equipment will not report on synthetic grass or earth courts.
7.2 Acrylic
7.2.1 Acrylic hardcourts - types of systems

Generally in Australia there are three types of acrylic surfacing systems:
• Non-Cushion
• Liquid applied cushion
• Mat laid cushion
Cushion systems must be applied to a
properly constructed asphalt or
concrete base. A newly developed
mat laid cushion surface is available
for loose lay application to a variety of
substrates including a proprietary
system (Dynamically Compacted
Base), cracked asphalt and concrete
bases, and existing clay court bases.
Base construction is discussed in
Section 6 of this manual
Acrylics come in a wide variety of colours, and colour charts are available from the
manufacturer (refer also to one such colour chart included in the appendix of this
manual). Generally the darker colours absorb heat more than the lighter colours. As the
surface can become hot, this should be kept in mind when choosing the colour for your
court.
The acrylic product usually consists of a binder [latex, acrylic, or a combination of these
materials], colour pigments, fillers, extenders, additives and preservatives. The better
quality coatings will generally have an acrylic binder, a high proportion of solids; fade
resistance, colour stability, good coverage, and mildew and fungus resistance.
Some or all of the acrylic coatings should contain silica sand. The particular grading and
particle shape of the sand content and the amount of sand incorporated in the colour
coating will dictate the texture and therefore the speed of play, the effect of spin, and
general playing characteristics. Only rounded silica sand should be used.
The grading of sand introduced to each coating is also crucial to the performance of the
coating, as well as the longevity of the finished surface. It is therefore highly
recommended, particularly for the top two coats, that the product delivered on site is in
factory mixed sealed containers.
Both non-cushioned and cushioned acrylic surfaces have excellent playing
characteristics, with good traction, and true bounce, and are available in a variety of
uniform surface speeds from slow to medium-fast. Generally a medium fast surface is
applied unless otherwise requested by the client. A cushioned surface will react a bit
Technical Manual 57
more to the type of spin applied to the ball. Both surfaces provide an all-weather surface
for year round play with relatively low maintenance.
7.2.2 Acrylic Application
7.2.2.1 Application on Asphalt

A new asphalt surface should be left to cure for at least 2 weeks, and preferably four
weeks before applying an acrylic surface. UV light from the sun as well as rain or other
water will assist in the curing period. If surfacing is attempted while the asphalt is still
volatile, splitting may occur through the acrylic coatings.
Before commencing surfacing, the asphalt should be water blasted clean and flooded or
inspected shortly after rain. Allow the court to drain for a period of half an hour at a
temperature of around 21°C or for a shorter period if the weather is hotter. Any low areas
or ‘bird baths’ holding water greater in depth than 2mm [this can be measured using a
20c coin] should be clearly marked to be patched out with filling compounds prior to
surfacing.
Additionally, carefully check the asphalt for small blisters while the court is wet. Blisters
would indicate some deleterious materials are present in the asphalt. Small blisters
containing these materials can be remedied by water blasting. Larger blisters or bumps
may have to be dug out and repaired with fillers.
Ironstone aggregate is sometimes present in the asphalt matrix, and this can cause
unsightly brown stains to appear on the surface over time, as moisture causes the
ironstone to form brown rust. Unfortunately there is no way of identifying that such
aggregate is present during installation of the asphalt. Some acrylic surfacing
manufacturers have special sealers available which can prevent the re-occurrence of
such rust stains once they have become apparent.
Carefully check the area where the asphalt run joins the next asphalt pass. Commonly
these areas are ‘bony’ and the asphalt is less dense. Ideally these should be filled and
re-compacted during the asphalt installation. However if not, then these areas should be
compacted by hand, and then filled to correct profile prior to surfacing. Always use fillers
as recommended by the acrylic manufacturer. If ingrained mud is present it will be
necessary to water blast these areas clean.
All patching and filling work should
be carried out utilising the
manufacturer’s recommended
products and specifications. Using
alternative products may void the
guarantees provided by the
manufacturer/applicator.
On completion of patching and filling,
all repair work must be sanded down
or ground to produce a smooth even
surface, with relatively uniform
texture. The surface should then be
thoroughly cleaned using a heavy-
duty blower to present a spotlessly
clean area ready for the acrylic
coatings.
Filled and patched areas should be inspected, and a preliminary coating of the base coat
applied to these areas, if required, to obtain the desired texture.
The base coat usually consists of an acrylic binder and a heavier grading of silica sand,
so that small voids and variations of texture in the asphalt is masked. This coat is applied
to the entire court area [fence to fence].
Technical Manual 58
When the base coat is thoroughly dry, inspect for ridges and ‘up-jumps’ [squeegee
marks], and scrape or grind smooth before proceeding with topcoats.
Normally one or two base coats and then one to three topcoats are applied to a new
asphalt surface, depending on the quality of the asphalt. No coating work should be
contemplated if rain is imminent.
Additionally, the air temperature should be a minimum of 12° and rising. Coating will
become extremely difficult once the temperature passes 30°, and in the interests of
achieving a quality job, work should cease at this temperature. Most experienced
applicators will use an infra-red thermometer to measure surface temperature, and will
only apply material in the surface temperature range of 12° minimum to 40° maximum
surface temperature.
All acrylic coatings are applied with a rubber squeegee. Sometimes a fine hair broom
immediately follows the squeegee pass. If the surface is level, a well trained and
experienced squeegee operator should not require a following broom pass. However, on
uneven surfaces such as old asphalt or concrete, a squeegee finish can result in ‘bald’
patches on high spots, and following the squeegee with a broom can eliminate this. A
broomed finish is often better for surfaces such as Netball where extra grip is required.
There are differing theories regarding the application of acrylics. Some manufacturers
and contractors recommend that the topcoats be applied in an alternate direction to the
base coat. Others say all coats should be applied in the same direction. Most
experienced contractors tend to squeegee across the court, particularly on warmer days,
as the shorter pass enables achievement of a more evenly textured surface.
On hot days the materials will tend to ‘chaff up’ and become unworkable. This tends to
support the theory that the coatings be applied across the court for the playing area, and
to utilise the shortest distance possible when applying the surrounds.
In any event, the coatings should be applied evenly and to a uniform thickness over the
entire court area. This will require an experienced applicator, and care should be taken in
choosing a contractor.
7.2.2.2 Two Colour Application

If the court is to be in two colours, with a contrasting colour for the surrounds, the four
corners of the playing area should be established [method of setting out a court is
included in this manual in Section 4.5.1], and marked with a washable marker. Do not
use timber crayon. A chalkline can then be applied to mark out the area.
One to three coats of topcoat materials are then applied to the playing area using a
squeegee, or a squeegee followed by a fine hair broom. A well-trained applicator will not
need to use a broom to mask squeegee marks.
Each coat should be thoroughly dry before proceeding with the next coat. Drying time will
vary according to the ambient temperature and humidity.
Once the playing area is completed
it should be accurately taped off
using a taping machine, then one to
three coats applied to the surrounds
in contrasting colours as chosen by
the owner. The edges of the court
should be finished off neatly with the
bottom sections of the fencing posts
taped off to prevent the acrylic
coating marking the posts. A strip of
masking tape around the edge of the
court will provide a neat, straight line
finish.
Technical Manual 59
7.2.2.3 Line Marking
In tennis, the lines are part of the inbounds area and, therefore, should have the same
texture as the playing surface. Textured lines should provide the same ball bounce
characteristics as all other areas of the court.
When the entire surface is completely dry, the masking tape is removed from the edge of
the playing area, and the entire court line markings set out [per the diagram in Section
4.5.1 of this manual].
All measurements are to the OUTSIDE of the lines [a ball touching only a small part of
the outside edge of the line is ‘in’], and no court dimensions should very by more than
6mm. All lines should be a minimum of 25mm wide, but 50mm is preferable and more
commonly used, with the exception of the base line, which can be up to 100mm wide. It
should also be noted that the rules of tennis call for the centre mark on the baseline to
extend 100mm into the court area from the baseline.
Lines should be continuous, however an option is to leave a gap of about 40mm open in
the singles sideline immediately behind the service line. This assists linesmen in calling
the serve if the court is to be used for championship play.
Lines should be taped using a taping
machine and masking tape, making
sure the tape is well tamped down, so
that paint does not run under the tape
and cause ‘fuzzy’ edges. Some
contractors are so intent on sharp lines
that they will pre-coat the tape with an
appropriate material, such as “Line
Sharp” clear sealer in order to seal the
inside edges of the tape prior to
application of the linemarking paint to
prevent paint inadvertintly being forced
under the tape and creating these
‘fuzzy’ edges. This technique usually
results in very sharp edges.
Alternatively lines can be applied using a gravity feed line marking machine, which
eliminates the need for taping. A reasonable number of applicators still prefer to apply
line paint with a brush and providing a proper brushing action is used, the results will
compliment the general court surface coatings. Whether the application is by brush or
roller, once sufficient line paint has been applied, it is important that the final motion of
either brush or roller be towards the wet film. This technique virtually eliminates brush or
roller marks.
High quality line paint properly applied
only requires one coat, regardless of
the method of application. Whilst
brush and roller are the usual means
of application, rollers are reasonably
fast and when used with an extended
handle, saves bending over.
The standard colour is white, and the
manufacturer of the surfacing product
should supply the acrylic line paint. As
previously stated and in most cases,
line-marking paint is textured, (with the
addition of fine silica), so that the ball
bounce and speed off the line is
relatively consistent with the rest of the
court.
On no account should traffic or oil based paints be used.
Technical Manual 60
When the tapes are removed all lines should be clean and sharp without variations in
paint consistency. The quality of this important final step can either complement or
detract from the coating system. Lines that are straight, with sharp edges and no brush or
roller marks, reinforce the quality of the colour coatings. However lines that are not
straight, or with edges appearing fuzzy because of line paint bleeding under the tape, or
lines that look wavy because of poor surface planarity, will detract from the total surfacing
effort.
It will take some time for the court surface to fully cure, so it is best not to play on the
court until after a couple of days of good drying weather. Using the court before the
surface has fully cured will result in shoes dragging colours across the lines, and from
one contrasting colour to the other. Also, premature use of a new court surface has led
to damage that resulted in premature wear of the court surface.
Owners are sometimes concerned about the following unexpected conditions they
observe in new courts:
a] Newly applied colour coatings may have slight variations in the surface. The
squeegee blade moving across the court from side to side [or end to end] will
cause the textured surface to reflect the sun and light so that it can appear
‘streaky’. This is a somewhat similar effect to that made by large mowers on
cricket or football ovals. A finished surface should be inspected for uniform colour
and texture at a distance of 8 to 10 metres, with the sun directly above or behind
the viewer.
b] Tennis shoes will leave scuff marks on a newly surfaced court. This is caused by
the sand content in the acrylic materials. It will decrease as the sand becomes
polished with play, and should not be of any concern. Black soled shoes (even
those claimed to be ‘non-marking’), however, leave very unsightly marks which are
almost impossible to remove, and should be banned from use on any acrylic court.
c] After the first few rainy spells, soap bubbles will appear on the surface of a newly
coated court. Detergents are added to the coating materials to assist with colour
dispersion. After several periods of rain the detergents will be washed out, and
this will no longer occur.
On indoor courts the detergents are not washed out, so if washed or wet, the
surface may be slippery for a few weeks, and care should be exercised when
initially using the courts.
d] Excessive ball wear and ball fuzz adhering to the surface may be evident on new
courts. This is caused by the sand content, and will diminish as the surface
becomes less abrasive.
e] As previously mentioned, using the court before it has fully cured may result in
sport shoes picking up colour pigments and causing scuff marks, particularly
across the white lines. In marginal drying conditions, allow a few days or up to a
week before using the court.
f] If the court is in an area where bird and flying-fox droppings are prevalent, it is best
to have a regular inspection. These droppings are acidic, and can eat through the
surface, causing a small piece of the court to lift out. They should be washed off
with mild detergent and warm water before damage occurs.
7.2.2.4 Application on Concrete

A new concrete slab must be allowed to cure for a minimum of four weeks before any
surfacing is contemplated. The longer it is allowed to cure the better.
It is imperative that the concrete itself is spotlessly clean, and no latence or concrete salts
are present on the surface. A simple test is to rub the palm of the hand on the concrete.
If a whitish residue is apparent on the palm then surfacing should be delayed until the
migration of concrete salts stops.
Technical Manual 61
Generally a concrete slab is treated with hydrochloric acid, using four parts water/one
part acid solution, and then water blasted clean prior to any surface application. The
surface should be thoroughly dry and clear of all concrete salts. All saw cut residues
must be removed during the acid etch and water blasting treatment.
As with coating asphalt based courts, all depressions holding water should be patched to
correct profile, utilising materials and methodologies recommended by the manufacturer,
and any high spots removed by grinding with a concrete planer. Expansion joints [usually
under the net line] should be filled with an elastomeric polyurethane joint-filler. To ensure
a bond with the surfacing materials, some fine sand should be rubbed into the joint-filler
surface prior to the curing process. Do not use acrylic caulking materials for expansion
joints.
When patching is completed, a prime coat as recommended by the manufacturer should
be applied to the entire court.
If a two-part epoxy primer is used, it is very important that the manufacturer’s
specifications are closely adhered to. The first acrylic coating should be applied while the
epoxy primer is still ‘tacky’ to touch. This will ensure a strong bond with the concrete
base while still allowing a degree of vapour transmission from the slab.
Once the initial coating of acrylic has been applied, it is best to leave the surface
overnight. The remaining two top coats can then be applied on the following day, given
good drying conditions.
Line marking can then be completed in a similar fashion as described previously in
Section 7.2.2.3.
7.2.3 Some dos and don’ts when coating acrylic tennis courts
7.2.3.1 Drying requirements

It is important for the water in the coating to evaporate out of the mix within three to four
hours after application. Water remaining in the film too long could affect uniformity of
colour, adhesion, and sand retention. If temperature is at low end of operating scale, do
not apply late in the afternoon.
7.2.3.2 Mixing and applying acrylic coating material

If adding sand on site to a Colour Concentrate material, add the sand to the acrylic
material prior to introducing water. However, a small amount of water may be needed to
adjust the viscosity to reduce the load on the mixing equipment.
Factory mixed materials only require the addition of potable water on site.
Use a soft [flexible] rubber squeegee blade when applying textured colour coating.
However, a stiff rubber blade may be used when fill coating.
Add material to the windrow in the lower half of the squeegee during application – i.e. the
half closest to the applicator.
Follow adding to the windrow with the squeegee as soon as possible, and do not allow
the windrow to dry out.
Mix (stir) the mixed materials just prior to using to keep the sand in suspension.
Wash all tools, squeegee blades and brooms as soon as possible. A wire brush is ideal
for cleaning equipment.
Apply the coatings in a straight line. Eliminate circular motions even in restricted spaces
such as between courts and/or behind baselines.
Apply the first two coats parallel to the net line [particularly in the play area].
Measure all mix ratios accurately.
Use textured line paint for tennis courts.
Technical Manual 62
7.2.3.3 Procedures to be avoided in applying acrylic coating material
Do not apply coatings unless the surface temperature is 12°C and rising.
Do not apply coatings if the surface has been exposed to freezing temperatures the night
before; i.e. allow the surface to rise to 12°C.
Do not apply material if surface temperature is above 40°C.
Do not apply subsequent coat until previous coat is completely dry. The interval between
coats is related to the drying conditions. Heat and low humidity accelerate drying.
Applying acrylic coatings during the night time hours of darkness is NOT recommended.
Do not apply acrylic coatings if the surface is wet.
Do not permit excessive material to remain in low spots on the final coat, otherwise these
areas will mud-crack and shine.
Do not pull material more than 18metres in hot or windy conditions.
Do not play on court surface for the first 24 hours after completion – longer if
temperatures are marginal.
7.2.3.4 Patching with a Recommended Patching Binder

Perhaps the most neglected area of surfacing or resurfacing tennis courts is the
identification and treatment of depressed areas that pond an excessive amount of water.
Filling and levelling a depression is one thing, but doing it in such a manner that it does
not reflect through the final coating takes experience and ‘know-how’. Patching is best
performed by an experienced applicator.
The traditional method of locating ‘bird baths’ is to flood the surface, wait 15 minutes, and
identify any depression that holds water deeper than the thickness of a 20c coin. At this
point the area in question should be outlined with a marker to show how far the patch is
to be applied.
Any depression approaching a depth of 6mm or more should be filled in with two or more
applications of patch mix. On the first application, the deeper the depression, the larger
the sand particle used in the mix. A deep depression should use a 30-60 mesh sand.
The larger sand will make a stronger patch as well as minimise mud cracking. The
second application should use the same sand as used in the filler coat mix. If only one
application is used, it is better to use the same sand as the filler coat mix.
7.2.3.5 Area preparation

On new courts it is necessary that the patch area be clean. New concrete surfaces
should be acid treated prior to any patching. Once the patches are dry the court may
then be primed with the manufacturer’s recommended product. On old courts it may be
necessary to chemically clean the area with an algaecide.
On old courts it is recommended the area be tack-coated with a dilution of 2 parts water
and 1 part binder. A good method of applying the tack-coat is to use a pump sprayer and
mist a uniform film over the entire depressed area. Do not allow the material to puddle.
The tack-coat should dry in 10 – 15 minutes and enhance adhesion. The area is now
ready to be levelled.
7.2.3.6 Patching tools:

The following tools are essential when patching court depressions:
• An aluminium or magnesium 2x4 metal screed long enough to bridge the
depressed area, steel trowel, brush and pump spray.
• A disc sander, belt sander and rubbing stone are traditional items that can improve
the quality of the patch.
Technical Manual 63
7.2.3.7 Mixing
The most expedient method of mixing used by most contractors is to use an electric drill
and stem mixer. If using an electric drill, it doesn’t matter what order the materials are
blended together. An accepted practice is to mix the binder and cement, then add the
sand. If mixing in a wheelbarrow or motor mixer, it is better to mix the dry sand and
cement to prevent cement balls, and then add the binder.
NOTE: it may be necessary to add more binder to improve the workable consistency of
the mix [do not add water to the mix].
7.2.3.8 Application of patching material

Pour the mix at the edge of the marked depression and pull the metal screed across the
low area, making certain no voids are left behind. If the viscosity of the mix is correct it
will require a slow, steady pull of the metal screed straight edge, i.e. there is no need for
a saw-cutting action. The metal screed should be held at an angle to the court surface so
that the mix is forced down under the screed.
Once the body of the patch is acceptable, the edges are feathered to a fine edge using a
steel trowel and brush.
NOTE: misting the patch surface with the water solution does not affect the mix, because
the water is on the surface of the patch mix and evaporates quickly. However care should
be taken to only apply a fine mist and not to leave any liquid solution lying on the
screeded surface, otherwise skinning can occur, leaving the surface water sensitive and
prone to later surface delamination.
7.2.3.9 Grinding patches

Often properly installed patches do not require much grinding or sanding. However, if the
planarity of the patch is not uniform and/or the edges are not properly feathered, it may
become necessary to use a mechanical means to correct the condition. Minor problems
may be corrected with a rubbing stone; however a disc or belt sander is fast and
thorough.
As a final step in hiding patches, it may be helpful to pre-coat the patches with the filler
coat mix.
7.2.3.10 Crack repairs

One of the most difficult tasks a contractor faces when surfacing or resurfacing tennis
courts is related to crack problems. It is relatively easy to fill cracks so that they do not
reflect through subsequent coatings for a short period. A very risky situation exists,
however, when one guarantees that cracks will not reappear over the longer term.
With few exceptions, cracks on outdoor surfaces are almost inevitable. The challenge is
to keep the cracks to a minimum, and hope those cracks that do return will be minor in
nature. In this case, minor means ‘hairline’ cracks, which do not affect the playability of
the surface.
Whether construction materials are hot or cold mix asphalt, or concrete, any surface is
subject to cracking. It appears that post-tensioned concrete courts experience the least
amount of serious cracking. Furthermore, cracks that do appear only amount to hairline
cracks because the tension on the cables keeps them closed.
There are three common causes of cracks:
1] Thermal expansion and contraction in which a surface reacts to rapid temperature
changes
2] Shrinkage cracks which usually result from a volume change of the surface
material soon after installation.
3] Structural cracks which are normally the result of subgrade failure.
Technical Manual 64
Cracks from volume change can occur in asphalt due to the nature of the mix design, or
inadequate compaction. Rapid curing causes volume change in concrete. Of the three,
structural cracks are the most severe, and the most difficult to resolve.
The forces of nature are unpredictable and much too forceful to guarantee that cracks will
not appear or reappear. Certainly many types of crack fillers have been used, and many
different systems of covering cracks have been tried over the years. To this day, no
material and no system of filling cracks have proven 100% successful. Admittedly some
fillers and systems deter the reappearance of cracks better than others, but inevitably
they return if there is movement in the surface or sub-surface.
Some contractors put considerable credence in the overlaying of cracks with a
membrane; however nature’s force will tear or distort the membrane if the cracks are of a
structural nature. Membrane overlays are best used only on hot or cold mix asphalt
surfaces that have ravelled, or experienced hairline cracks from volume change. A more
expensive method is to overlay the surface with hot-mix or emulsion asphalt; however
this type of overlay system is not completely successful.
Perhaps the most successful system is one that uses the ‘slip-sheet’ principle, where
there is no direct adhesion to the existing surface.
The most expedient and economical approach to cracks is to make certain the cracks are
cleaned of dirt and/or vegetation, and then filled with appropriate crack filler. By using
high-pressure water equipment, cracks can be cleaned so as to promote adequate
adhesion of the crack filler against the sides.
Once the cracks have been cleaned and dried, it is a good idea to tack the sides of the
crack with one of the products suitable as a tack coat. Manufacturer’s instructions should
be followed for mixing and drying time.
Normally the crack filler is worked well into the crack with a broad knife. Merely bridging
the crack with the filler will not produce satisfactory results. Pressure on the filler should
be applied in all directions in order to fill all the voids, and all excessive material removed
so that the filler will not reflect through the subsequent coatings. Once dried, some
grinding may be necessary to remove any ridges. Usually a rubbing stone is used for this
purpose.
REMEMBER:
1] Clean cracks
2] Tack coat
3] Fill cracks
4] Remove ridges
7.2.3.11 Recommendation for large

structural cracks:
Make a dry mix of sand and cement [3 parts sand to one part cement], and work the DRY
mix into the crack. The dry mix will fill the entire depth of the crack, thus eliminating any
voids. Sweep off excessive dry mix to a depth of about 1cm from the top. Pour a
solution of binder and water [mixed 1:1] on the dry mix. This will wick into the mix
causing it to harden. After the mix dries, use a regular binder mix to fill and level the
crack.
CLIENTS SHOULD BE ADVISED THAT STRUCTURAL CRACKS WILL REAPPEAR.
7.2.3.12 Painting lines

The final phase of the surfacing or resurfacing of recreational areas is the application of
the playing lines. The quality of this important final step can either complement or detract
from the coating system and the aesthetics of the finished court.
The preparation and application of line markings is discussed in depth in section 7.2.2.3
of this manual rather than being repeated here.
Technical Manual 65
REMEMBER: The rules of tennis require all lines shall be not less than 25mm wide, or
more than 50mm in width, except the base line, which may be up to 100mm in width. It
should also be noted that the rules call for the centre mark to be 100mm long.
In summary, it is important to install textured lines that are straight, with sharp edges and
streak free (i.e. with no brush or roller marks).
7.2.3.13 Pouring windows

All acrylic coatings tend to show a noticeable ‘streaking’ effect at the location where
additional material has been added to the windrow.
As the windrow is moved along the surface, the percentage of water in the mix is
reduced. This means the chemistry of the mix has been altered. When fresh material is
added to the windrow it will contain a different percentage of water. Perhaps other
chemicals as well may have been altered due to the surface temperature.
This problem is compounded when working on a hot surface. Consequently, it is always
best to apply the final coat early in the morning while the surface is relatively cool.
Experience has shown that these pour marks can be made less conspicuous by -
1] Applying the final coat early in the morning or on a cool day, when the surface
temperature is low
2] By pouring the fresh material on the wet acrylic film rather than on the dry or
uncoated surface.
It is also a good idea to pour the material right behind the squeegee man while the acrylic
film is as fresh [wet] as possible.
7.2.4 Cushion Acrylic
7.2.4.1 General
Cushion acrylic surfaces appear, to the eye, similar to a standard acrylic hardcourt
surface. However, these highly technical surfaces are ‘soft’ underfoot, providing
cushioning to the foot fall so as to reduce fatigue and injury. Perhaps the best know of
these surfaces in Australia are “Plexicushion” (the current Australian Open surface) and
“Rebound Ace” (the previous Australian Open surface).
There are a small number of other cushion acrylic surfaces available in Australia, but little
is known about the quality of these surfaces and the way in which they are being
installed. The reason for this is there are very few recent examples of these surfaces,
and even fewer have been made available for inspection and assessment by Tennis
Queensland and/or Tennis Australia.
Cushion acrylic surfaces require installation over a sound base structure. Please refer to
descriptions in Chapter 6 for details of asphalt and concrete base structures.
7.2.4.2 Base preparation

Base tolerance for cushion surfaces is similar to that for standard acrylic hardcourts.
Planarity is reported by measuring the deviation beneath a 3m straight edge. The target
is 3mm beneath the 3m straight edge placed anywhere on the surface. It should be
remembered that the intention is to ensure that the court drains quickly following showers
or storms and that the surface does not produce uneven bounce. The 3mm tolerance
may be difficult to achieve on some bases, for example, asphalt.
Asphalt must be cured for a minimum of 14 days before installation of the cushion
system. Concrete bases require longer curing times before application of the cushion
acrylic surface.
Asphalt is cleaned by blasting with a high pressure water cleaner and must be free from
all dust, dirt, grease etc. The surface must be thoroughly dry before application of the
cushion system.
Technical Manual 66
Concrete must be cured for a minimum of 28 days before installation of the cushion
system.
Concrete is etched with a hydrochloric acid solution to the manufacturer’s specification.
All acid residue is then removed using fresh water under pressure and all dust, dirt
grease, etc must be removed. The concrete must be thoroughly dry before application of
the cushion system.
7.2.4.3 Types of cushion acrylic surfaces

Cushion acrylic surfaces fall into two broad groups, “wet lay” systems and “mat lay”
systems. They are quite different surfaces in the way they are installed and costs can
also vary significantly depending upon the composition of the system selected (i.e. the
number of layers of each material type used). Mat lay systems are further divided by the
thickness of the cushion used and design parameters.
Cushion layers are complex technical/chemical systems and should be installed by
trained applicators approved by the product manufacturer.
7.2.4.4 Wet lay systems.

Installation of Wet lay systems
involves the spreading of a liquid
rubber compound over the
specially constructed asphalt or
concrete base, building up in
layers until the desired cushion
thickness is achieved.
The thickness of the rubber
installed determines the
cushioning achieved and, of
course, the cost of the surface.
An advantage of a Wet lay system
is that the thickness of the cushion
can be adjusted to suit cushioning or budget requirements. Following installation of the
cushion layers, an acrylic surface is then installed over the top. Typically, wet lay
systems range from 1mm to 5mm in thickness. The best known wet lay system used in
Australia is the range of “Plexicushion” products - Club, Tournament and Prestige. The
“Plexicushion Prestige” product is the current Australian Open surface (since 2008).
Another wet lay system that has been installed successfully in Australia (although not so
much in recent years) is the “Rebound Ace Pro” system.
Internationally, the “DecoTurf” product has been the surface used at the US Open for
many years.
7.2.4.5 Installation of wet lay systems

The base is prepared as described above.
Asphalt is firstly treated with an acrylic “resurfacer”, applied using a rubber squeegee.
The resurfacer serves two purposes, it provides a primer coating to assist adhesion of the
cushion material and fills imperfections and pores in “bony” open surfaces.
Concrete is prepared using different sealers. The concrete sealer is applied using either
squeegee or roller and promotes adhesion of the cushion material to the concrete base.
Cushion material is delivered to site in drums and mixed, on site, with potable water in
accordance with the manufacturer’s recommendations. The cushion material is then
applied in layers, again using a rubber squeegee. Initial layer(s) consist of a coarse
material; subsequent layer(s) are a fine material. Cushion material must be allowed to
cure between coats.
Ideally, three coats of specially formulated acrylic are applied in a similar fashion to a
standard acrylic hardcourt. The court is finally line marked for play.
Technical Manual 67
7.2.4.6 Mat lay systems.
The base is prepared as described above.
Asphalt is treated with an acrylic “resurfacer”, applied using a rubber squeegee. The
resurfacer serves two purposes, it provides a primer coating to assist adhesion of the
cushion material and fills imperfections and pores in “bony” open surfaces.
Concrete is prepared using different sealers to those specified for asphalt. The concrete
sealer is applied using either squeegee or roller and enables adhesion of the cushion
material to the concrete base.
Mat lay systems differ in that the cushion layer is delivered to site in pre manufactured
rolls of predetermined thickness. These are rolled out and placed accurately in position
with all edges tightly fitted, and then lifted and adhered to the surface using purpose
developed adhesives. A significant feature of the adhesive is the lack of “tack”. This
makes it difficult for the installer and it is most important that mat lay systems are installed
by experience applicators trained and approved by the surface manufacturer.
Within the family of mat lay systems, several different types are in common use. The
various mat lay systems currently available are generally supplied in either 4mm or 7mm
cushion thickness.
7.2.4.7 Installation of mat lay systems

Adhesives used for Mat lay courts consist of a two-part poly urethane system. The
adhesive is mixed on site using mechanical mixers and has a limited “pot life”, that is, it
must be used before it commences to ‘set’. This places demands on the surface installer
in regard to quantities mixed, number of applicators on site, area covered with each mix,
etc. As with all adhesives, application rates are critical.
Adhesive is applied to the dry, dust and grease free concrete using hand trowels and
squeegees. Sealing of joins and court edges to prevent water ingress is a critical stage
of installation.
When curing has been achieved, the mat is then sealed using a proprietary two-part
polyurethane sealer that is also mixed on site. Great care is taken to ensure no
imperfections exist on the surface. Any irregularities need to be ground off when the seal
coat has cured.
Finishing varies depending on the system installed. Impact systems are sealed and then
surfaced with the colour coats. Some systems are covered with an additional layer of
reinforcing material prior to the application of the colour coats and line marking.
7.2.4.8 Maintenance of cushion acrylic surfaces

It is important to follow manufacturers’ specifications for maintaining these highly
technical surfaces.
In general terms, maintenance is similar to standard acrylic hardcourts. Restriction of
marking-sole sports shoes is recommended. Maintenance of court surrounds, in
particular drainage, avoidance of tree-root infestation, etc is recommended. These
issues are covered in Section 4.6 in this manual.
Annual surface cleaning is recommended using a high pressure water cleaner. Use of a
wand held above the court surface is safer than a rotating head cleaner as more control
over the pressure applied to the surface is possible.
Bat droppings have a corrosive effect on acrylic surfaces and should be removed
promptly where the courts are in close proximity to bat colonies.
Periodic renewal of the colour coat will be necessary and should be included in
maintenance budgets for these and all sports surfaces. The surface installer will provide
advice on anticipated court life given expected traffic. As a general rule, clubs should
budget to recoat the surface every five years.
Technical Manual 68
7.2.5 Choice of colours for acrylic surfaces
Acrylics come in a wide variety of colours, and colour charts are available from the
manufacturer. Generally the darker colours absorb heat more than the lighters colours.
As the surface can become hot, this should be kept in mind when choosing the colour for
your court. Examples of the colours available can be found on many of the product
manufacturer’s web sites.
7.2.6 Maintenance and repair of acrylic surfaces

Refer to sections 7.1.5.1 and 7.2.4.8 above for maintenance requirements of acrylic and
cushion acrylic court surfaces.
Refer to section 7.2.3 for information relating to the correct application and repair
techniques with regards to acrylic court surfaces.
7.2.7 Resurfacing
Before calling for quotations to resurface an existing acrylic surface, the owner should
make a careful inspection of the court surface. A list of defects should be made and
discussed with the contractor/s so that both parties are aware of the scope of works to be
carried out. All the items to be attended should form part of the quotation. Generalised
quotations simply stating “Repair existing surface and apply new acrylic coating” should
not be contemplated.
Work to be carried out should be itemised in as much detail as possible. Quotations
should also be accompanied by a copy of the manufacturer’s specification for the use and
application of the product to be applied.
Decisions and directions taken regarding resurfacing an existing acrylic surface may
include some or all of the following (Note: these items are only summarised here as they
are each discussed in more detail in Section 7.2.3 and associated sub-sections):
Cleaning of existing surface. All mould and mildew must be killed and removed from
the surface. Simply water blasting the mould will not eliminate all the spores, and new
growth will occur within a short period of time. An appropriate algaecide must be applied
to the entire area and then washed clean. The contractor shall be totally responsible for
the collection and disposal of the waste products of this cleaning process.
Grinding back existing lines. All existing cracked, raised or glossy line marking paint
should be ground back to the upper coating of the acrylic surface. If existing lines are
level with the court surface and no build-up is apparent, then full removal of lines should
not be necessary. It would be wise, however, to apply a wash coat to the lines prior to
resurfacing to prevent the new product sliding across the polished lines.
Pressure cleaning. The entire surface should be pressure cleaned prior to applying any
new product to the court surface. This pressure cleaning is prior to all patching work,
filling of depressions, tack coating, etc. The contractor is to be responsible for appropriate
disposal of all waste materials.
Delamination of surface. Pressure cleaning will reveal any weak spots or delamination
in the existing surface. These areas may be ground back to remove all unstable product.
Areas ground back are then bought back to the correct profile with the surrounding
surface. The contractor should only use products recommended by the manufacturer of
the acrylic coating to be applied. The patching materials should only be applied according
to the manufacturer’s specification, which should be made available on request.
Areas holding water. The pressure cleaning will also reveal depressions that hold water.
These are termed “bird baths”, and are defined as areas that after 15-20 minutes of
drying are still holding water in excess of the thickness of a 20 cent coin at its deepest
point. These areas are deemed to be unacceptable, and should be patched to correct the
profile. This definition should be clearly understood by both client and contractor and
areas to be treated agreed to by both parties. Depressions are identified and defined only
with a washable marking chalk to avoid permanent marking of the surface. These are
then patched to the correct profile using specific products as recommended and specified
Technical Manual 69
by the acrylic surfacing manufacturer. Deep depressions may require two or three
applications of patching materials to correct the profile. Each application must dry
thoroughly before proceeding to the next layer. Inadequate drying may result in “ghosting”
of the patch appearing in the finished court surface.
Repairing cracks. Invariably most old court bases will have some degree of cracking
that reflects through the surface. These can be defined as minor or major cracks.
Minor cracks are generally of a shallow depth and are due to the combined effects of
shrinking and ageing of the base materials. As a guide, minor cracks and “alligator”
crazing can often be successfully repaired with the use of fibreglass mesh or scrim. It
must be accepted that over time, however, some evidence of cracking may again reflect
through the surface materials.
Major cracks are of a structural nature mainly due to movement beneath the base.
Typically such structural cracks are of appreciable depth, and may be full depth through
the entire base construction. The treatment of cracks may vary from contractor to
contractor. However, both client and contractor should have a clear understanding as to
the scope of the work and the likely results. Due to their nature, major cracks will
inevitably re-appear within a relatively short period of time. The only long term remedy
with such cracking is to either rebuild or reconstruct the base after consultation with an
engineer.
Clients should be made aware that not all cracking can be eliminated by a resurfacing
procedure, and contractors should also make this clear in their quotations.
Workmanship for repairs. Depressions should first be tack coated to ensure proper
adhesion of the patching materials. All patched should be feathered out at the edges so
that no ridges are apparent. The patch should be sanded down so that the patch is
blemish free. It is then advisable to apply one coat of base coat material over the patch to
obtain a textures surface finish similar to the surrounding existing court surface. This
procedure should be carried our prior to applying the first coating of resurfacing materials
to the entire court.
Cracks should be thoroughly cleaned out, and all debris removed prior to any treatment.
Major cracks should be treated by grinding out or using a V shaped chisel to compact and
‘V out’ the crack (asphalt only). All chiselling or grinding dust must then be removed from
the crack. Crack filler or patching compound as recommended by the manufacturer can
then be applied according to specifications. All crack filler materials should be thoroughly
worked down into the crack. The materials should then be allowed to dry, and then
ground off to correct court profile. All repair work should be pre-coated (as for
depressions) prior to resurfacing.
Cleaning of surface. Once all repair work has been completed and the repair work pre-
coated, the entire court surface should be cleaned with a heavy-duty air blower,
combined with an operator using a hand scraper to thoroughly clean the court surface.
Application of new surface. Two or three coats [contractor should clearly specify in his
quotation] of an approved tennis court surfacing product should then be applied strictly
according to the manufacturer’s specifications. Mixing of the materials should take place
on site, and immediately prior to commencing the resurfacing procedure.
Materials can be applied solely by a squeegee, or by squeegee followed by a fine hair
broom, but should never be spread by broom only. It is preferable to keep the squeegee
‘runs’ as short as possible so that material does not ‘chaff up’ in hot weather. Each coat
must be allowed to dry thoroughly prior to proceeding with the next coat. All work marks
and minor blemishes must be scraped prior to a following coat.
Line Marking. Do not use airless spray equipment, as this will not provide a sharp edge
on the lines. The court dimensions should be marked out according to the rules of tennis,
and then, using a mechanical tape-laying machine, accurately place the longitudinal lines.
The straightness of the lines should be checked and attended to if required. The tape
should firmly adhere to the surface, and then the line-marking paint is applied by hand
brush or roller.
Technical Manual 70
Once the paint has dried, the tape may be pulled up, and the baselines and service lines
painted on in the manner already described. The contractor should use line marking paint
as recommended by the acrylic surface manufacturer. Some manufacturers supply a
textured line paint to reduce the faster ball bounce off the lines.
Reference should also be made to sections 7.2.2.3 and 7.2.3.12 for more detailed
information relating to line marking preparation and application.
Limitations. Acrylic materials should not be applied in high wind conditions. Surface
temperature should be in the range of 12deg C to 40deg C. The material will dry too
rapidly in surface temperatures above 40deg C, and will not cure properly in
temperatures less than 12deg C.
Hold Points.
(1) Inspection of the cleaned surface and agreement on depressions to be filled and
cracks to be repaired. Client must be aware that structural cracking will almost assuredly
return.
(2) Inspection and acceptance of repaired surface prior to new surface coatings.
(3) Inspection of finished surface. This should be done at about midday and at a distance
of some three metres from the court surface. The surface should appear uniform in
colour and texture, and free of noticeable blemishes. Allowance should be made for a
slight ‘windrow’ effect. The alternating squeegee spreading of the materials will be
apparent at different times of the day. This can be likened to the patterned mowing
appearance on grass cricket and football fields, golf courses, and for that matter on grass
tennis courts.
(4) Final inspection after line marking.
7.3 Synthetic grass
7.3.1 Definitions used in this section

Backing Material Woven material, usually polypropylene, into which the fibres that
make up the synthetic grass are woven.
Clean Sweep Brand name of popular court grooming device consisting of a mat
like structure that is dragged across the court. The device gathers
leaves and other debris that can be disposed of away from the
playing surface. The “Clean Sweep” also re-distributes the infill
sand evenly across a synthetic grass surface.
Decitex The Canadian and European equivalent to denier; equals the total
weight in grams of 10,000 meters of fibre.
Denier A unit of fineness for fibres, based on a standard mass per length
of 1 gram per 9,000 meters of yarn.
Helicopter Trowel Mechanical trowel used to achieve planarity in a concrete slab, so
named because of the rotating blades.
Pile The green (usually) fibre material that forms the playing surface in
the outdoor carpet courts.
Pile Height Length of pile. The standard pile height for synthetic grass courts
is 19mm.
SFAG Sand Filled Artificial Grass
7.3.2 What is Sand Filled Artificial Grass (SFAG)?

Sand-filled artificial grass (SFAG) is, quite simply, a green coloured outdoor carpet that
has been filled with sand, so that the tips of the fibres protrude giving the appearance of
natural grass. However, this simple description defies the technology that has gone into
the development of this product.
Technical Manual 71
The carpet is manufactured in a similar
manner to traditional carpet; however, the
materials used in its manufacture are quite
special. The carpet consists of a backing
material with the ‘pile’ made of a propylene
yarn inserted on a loom in a manner similar to
a normal indoor carpet.
The basic materials making up the surface are
illustrated in the Figure on this page. They are
the backing material, the pile and the sand
infill. The backing material and the pile are
generally manufactured from propylene, which
is an extremely durable product that, when treated, resists the destructive effects of the
environment.
The combination of the yarn material used to produce the pile and mineral sand infill
creates a sports surface with characteristics unlike most other tennis surfaces. Now
twenty-five years from its introduction to the Australian market, it has found its place in
many tennis clubs and on a majority of private courts around the country and is most
popular for resort courts and with older players.
The range of different synthetic grass surfaces is extensive. There is wide variation in the
design of synthetic grass surfaces as manufacturers continue to experiment with yarn
variations and the ratio of yarn to sand. However, the product which seems to have
evolved as a “standard” is a 19mm pile height, 10,000 denier carpet.
For the technically minded, this is 19mm pile height, 10,000 denier carpet with an
average of 21 stitches to 100mm or 210 stitches to 1.00metre, a gauge of 10 mm and
ideally filled with a majority of
750 micron “rounded” sand
particles, preferably darker in
colour.
The effect of the combination
carpet and sand is to create a
hardy earth-like sports surface
underfoot with characteristics
similar to but more easily
maintained than other earthen
mediums such as natural turf
and natural clay-based surfaces.
As with all tennis courts, poorly
constructed base structures are
often the real explanation for
synthetic grass courts described
as having "bad surfaces"
Properly installed over a well-
constructed base, one of the
greatest advantages of synthetic
grass to tennis clubs and
commercial centres is its
drainage capacity and recovery
to playing standard following
rain. Less play time is lost to
inclement weather with these
surfaces, usually allowing play
to continue immediately after
rain which may make play
unsafe on another surface.
Technical Manual 72
7.3.3 Player preferences
The tennis players’ preference for surfaces is too diverse to suggest any one surface as
being “the best”. Surfaces such as synthetic grass, ant-bed or hardcourt are favoured by
different players. Within the range of synthetic grass surfaces available, debate also
occurs over which particular specification is the best. Individual preferences exist for grip
or slide, hard or soft, high sand levels or low sand levels, ‘standard’ pile height or short
pile, etc. Adding to this debate, the ball can often react quite differently from court to
court due to the various surface textures of the different synthetic grasses available.
The choice of court surface, or mix of surfaces, often presents a difficulty for the decision
makers who are planning a refurbishment or establishment of a new club. Traditionally,
where club membership is made up of older or Veteran players the preferred surface is
synthetic grass, often in conjunction with a road-base court platform. These players
generally agree that the greater impact absorption and slide capacity of synthetic grass is
kinder to aging joints. Adding to this is the advantage of less rain interrupted playing time
and the extra club income gained from social bookings.
Ultimately, the choice of surface is best made by the users of the facility. A poll of court
users, usually the club members, will lead to a surface choice that will keep membership
levels healthy. Membership is the most important factor in the long term viability of a
club. A choice made on cost alone will not best serve the long-term interests of the club.
The tennis construction industry offers a range of base and surface options to satisfy
court owners’ preferences. Informed decisions result from thorough membership
investigation that may include researching the experiences of other clubs, speaking with
court builders and seeking advice from the State Tennis Association.
7.3.3.1 Surfaces for social play.

Social players often prefer synthetic grass, based on the general ambiance, feel
underfoot, comfort on the body, etc. The ability to recover following showers or storm is
also attractive as it reduces the number of cancellations of the weekly bookings caused
by rain.
7.3.3.2 Surfaces for competition and tournament play

Synthetic grass is less preferred for competition play. At this point in time, Tennis
Australia will not sanction any professional tournament or elite junior tournament on
synthetic grass or synthetic clay surfaces. Hardcourts provide opportunities for a more
tactical game where the court speed and foot grip encourage players to plan several
strokes ahead of the winning shot. It is for this reason that Tennis Australia encourages
the use of hardcourts for developing juniors as future champions. Conversely, synthetic
grass properties encourage players to end a rally early.
Notwithstanding this, synthetic grass is very popular with clubs and is regularly used in
club competitions around the country.
7.3.3.3 Compromises for club committees.

The popularity of SFAG presents a difficult situation for tennis decision makers who are
trying to encourage excellence in stroke making and court craft and require a surface that
is consistent to teach these skills so as to keep pace with rapidly improving world talent.
A large proportion of our emerging youth often gain their early experience from domestic
and club synthetic grass courts but are quickly moved to hardcourts so that these skills
can be honed. Further development of well advertised maintenance processes for SFAG
courts is required so that these varying surface types can be complementary rather than
adversarial.
7.3.4 Selecting a synthetic grass product.

The choice of which synthetic grass best suits an application is difficult. The synthetic
grass manufacturing industry offers such a wide choice in materials, many of which look
very similar and it becomes difficult for even experienced judges to make an informed
decision.
Technical Manual 73
Manufacturers are known to regularly alter the specification of their yarn and material
suppliers creating inconsistencies with specification data for individual products from year
to year. Tennis court building contractors who tend to be the intermediary of this
information invariably claim valid reasons why the product they offer is superior to that of
their competitors and thus it becomes very difficult for the buyer to make that properly
informed decision.
Ideally, an objective durability test would predict the life span of a surface. Similarly,
some form of “playability index” predicting the comfort for the players would assist.
Unfortunately these objective measures are not available.
In the absence of a test for durability, the industry has chosen “face weight” as a measure
of durability. Face weight is the weight of yarn that makes up the pile, measured from the
top of the backing material to the tip of the pile. This measure works on the principle that
the greater weight of yarn used, the better the product. This measure relies on the higher
weight products lasting longer and assumes that each of the yarns being compared
exhibit equal wear for a given mass. No objective measure exists for ‘playability”.
So, what is the correct choice? What makes one product superior to another? The
answer is difficult given the small amount of data collected to date and the lack of records
kept on individual court usage. Perhaps it is most appropriate for the buyer to deal only
with manufacturers and contractors who have a proven track record and reputation as
assurance of gaining the products and warranties necessary to long term satisfaction.
7.3.4.1 Pile height

Synthetic grass is manufactured in a range of pile heights. Most common are12mm,
16mm, 19mm, 22mm, 34mm. Others may be manufactured from time to time.
Just as in yarn denier (or Decitex) and stitch rate, pile height is also often varied to suit
different sports, or to arrive at a product with alternate tennis playing attributes. One such
product is now produced by most manufacturers and features a lower 16mm pile height
often with a lower denier (Decitex) yarn but a much increased stitch rate. Properly
installed, the result is a surface which is much greener in appearance since less sand is
visible and which features a more certain foot grip more often associated with hardcourts.
However, the all important sand content and its ratio to the yarn, along with refined
installation techniques remain crucial to production of a successful tennis surface.
7.3.4.2 Yarn varieties

“Yarn” describes the material that comprises the fibres that give synthetic grass its
appearance.
Polypropylene is the yarn that has been most successful to date for Tennis with nylon
enjoying pride of place for many years for the sports of Field Hockey and American
Football, while the use of polyethylene is popular for Soccer. The introduction of
polyethylene yarn into Tennis products highlights the ongoing development by the
industry and manufacturers looking for an edge. This success of trials using different
yarns has been mixed.
7.3.4.3 Settling in time

The majority of SFAG sports surfaces will require a period of time to “settle in” before
arriving at a point where they can be considered to be playing at their best. This time
period can vary from 3 months to 18 months subject firstly to the method of and care in
installation of both synthetic grass and sand infill and secondly to the amount of play it
receives. Usually more use is best. The third and probably most important factor in
achieving excellence in the playing surface is maintenance. A simple brooming and
bagging regime can not only accelerate this “settled in” status but will create a
consistency in playing characteristics that will satisfy the toughest critic.
Technical Manual 74
7.3.4.4 UV rating and deleterious effects of the environment
Although production of yarns without ultra violet inhibitors is a thing of the past, this
remains an important factor in the long term performance of the completed carpet.
Glazing, or the action of surface fibres matting to form a hard and slippery crust, appears
to be less of an issue than earlier years but is still seen on various courts. The industry
remains undecided on blaming any one cause but rather a number of issues that come
together in an apparent haphazard way to create the problem. The tips of the fibres split
vertically as is considered normal but marry together then gather microscopic splinters of
this fibre (often seen washed to the side of the court after heavy rain) together with other
environmental fallout and set to form “glazing”
Glazing usually occurs in the heavy wear areas around the base-line first and is often
seen at one end only of the court suggesting that loose particles figure heavily in the
formation of the crust as it also seems to occur at the low end of the court first.
7.3.4.5 Various manufacturers

A number of manufacturers of synthetic grass and SFAG now exist in Australia along with
overseas suppliers assuring the sports surface consumer of a healthy competition with
pricing always keen. Although the principle of mineral infill of synthetic grass arrived in
Australia more than 25 years ago from overseas, much of its further development
occurred in Australia and this development has gone back out to the world from here.
7.3.5 Mineral infill sand

The sand infill has a number of effects on what is generally an unremarkable carpet and
its importance both in type and installation process often is, but should not be underrated.
The task of the pile is to hold the sand in place while it in turn holds the pile upright
allowing only the tips of the yarn to be exposed to foot traffic and the elements.
Synthetic grass manufacturers have been slow to agree on what is the ideal or most
appropriate finished level of sand for their products and perhaps this is because it finally
comes down to player or club preference. What is still required is sufficient knowledge
and interest among the industry advisers to be able to assist the end user in arriving at
final sand levels. While maintaining an excess of sand can protect the carpet from wear,
it makes for less than ideal playing conditions both for ball bounce and footing and
creates a greater need for sand levelling services.
7.3.5.1 Grain size -minus one -750

micron
Finished sand levels will create varying play
characteristics so that the choice of sand type
and application method of the mineral infill is
critical to the outcome.
While the size of the sand grains is important,
the greater issue is that the majority of infill is
the same grain size and that it be non-angular
in shape. Sands available to the industry vary
quite dramatically around the country both in size, shape and colour but most have
settled on a range between 0.5mm to 0.8mm. The more rounded (non-angular) shape
will assist in preventing premature compaction of the sand and helping with drainage.
Some contend that grain size over 1mm is desirable because of its benefit to drainage.
Because of the larger voids between the grains drainage flow rates must be improved but
the heavier grain may cause extra abrasion to the yarn underfoot, thus hastening the
wear process.
Whichever the choice a sieve analysis available from your local sand supplier will show
that the majority of the supplied sand will be of a single size with smaller quantities
ranging down to dust included but in far smaller proportions. These dust particles can be
most injurious to the synthetic grass. Firstly they can be responsible for clogging up the
Technical Manual 75
voids expected to be created with the chosen sand grain thus inhibiting drainage and
secondly assisting undesirable compaction. It can also assist the “glazing” process as
they are drawn to the surface during heavy rainfall. Playing characteristics of the surface
can be affected, sometimes creating slippery playing conditions. It is hoped that few
particles over the preferred size are included.
As part of the sand production the sand is sieved, washed and kiln dried. The washing
process aids in removal of unwanted material and the dust particles. The kiln drying of
the sand assists in neutralising any living organisms or vegetable matter captured in the
mining process but its prime reason is to produce a dry material which allows its
integration with the polypropylene yarn of the synthetic grass.
7.3.6 SFAG installation

The installation of SFAG commences with inspection and acceptance of a suitable base
followed by a relatively simple carpet installation operation. This is complicated by a few
features relating to knowledge of the product and line-marking for the game of tennis.
Although the long pile and the mineral infill can disguise defects in both base and carpet
installation techniques extreme care is still required with laying and joining processes.
Two items important to SFAG or in fact any installations for the game of tennis are:
(1) Exactness of positioning and straightness of line and
(2) Consistency of surface which allows confidence in ball bounce and footing.
If these elements are produced (and maintained) the players can be satisfied with SFAG
as a playing surface.
Most manufacturers now produce their synthetic grass carpet with the majority of the
tennis lines in-built and the following presumes this to be the case. Other sports very
suited to the use of SFAG such as netball, basketball, volleyball and hockey may require
much of the line-marking to be “cut in” manually but the processes will remain the same.
The width of the tennis playing area is
10.98metres (36 feet) and the carpet is 3.66
metres wide (12 feet) so that the set-out of the
SFAG is almost always going to start with three
12’0”widths (36’0”) through the centre of the
court area with the tram-tracks and centre line
woven into these three widths. These carpet
lengths are carefully fitted to pre-marked chalk
lines on the base and manually cut where
overlapped to make good joins prior to gluing
together.
These lengths are followed by the addition of the sections from tram-tracks to the fences
on either side and then by the base-line sections at each end. In most cases these
sections will include the actual base-line which may vary in width according to the rules of
the game (1 inch, 2”, 3” or 4”) and the preference of the end user. It is important to note
that these base-line lengths are laid “end-on-side” to the earlier sections of installation
(contrary to good carpet laying techniques) and will present as a very different colour
because of light reflected differently from each. Care must then be taken when applying
the sand infill to correct this variation by “standing up” the pile on both base-line and
general play areas. Done correctly this apparent colour difference will disappear.
Joining failures through use of inappropriate adhesives and/or application processes
have been one of the most damaging and obvious features of installations performed
over the last 25 years and through insufficient education and supervision of installers it
will continue to be a problem. Such failures are usually exceptionally difficult and
expensive to repair, often prompting the premature replacement of the carpet.
After achieving satisfaction with the trimmed joins and straightness of the line a joining
tape is placed centrally under the juncture of each two widths. In the absence of
manufacturer’s direction to the contrary these tapes should be a minimum of 400mm wide
Technical Manual 76
at base-lines and joins where a line is being inserted (e.g. both service lines) and a
minimum of 300mm wide at most other joins. Adhesive recommended by the SFAG
manufacturer is then applied to the tape and the two sections are bonded.
The latex backing applied to most SFAG products is intended for pile retention and to
give the carpet some body to assist its transport across the country to its final destination.
Its bond to the polypropylene scrim (carpet backing) and yarn is not good, a chemical
bond to polypropylene being difficult to achieve. Equally the bond of the recommended
joining adhesive to the latex and poly-yarn is not strong and must be assisted by creating
a mechanical bond which relies upon width and depth of adhesive to achieve its success.
Again, in the absence of specifications, the adhesive spread should extend to within
20mm of the edges of the joining tape taking care not to allow spillage onto the base. For
most standard SFAG qualities a 3mm “V” notched trowel should be used so as to apply
the correct quantity of adhesive to properly transfer to the heavily textured backing of the
carpet. When joining carpets with less textured backing, finer notched trowels could be
used. Care must also be taken to ensure that trowels or trowel blades are replaced as
they wear down.
After allowing an appropriate time for the
glue to “gas off” (the solvents will dissipate
into the atmosphere) the two carpet
sections are brought together and pressed
onto the tape making sure that the gap
between the first ribs of each section is no
greater than the gauge of the carpet being
installed (usually 10mm). Transference of
the adhesive to the carpet is the first
priority and this is usually achieved with a
heavy roller. When sufficient time has
elapsed for the adhesive to “tack off”
(usually about 20 minutes) this rolling process should be re-done to cement the bond.
Subject to both the adhesive and the weather conditions no stress should be applied to
this bond for a minimum of two hours. This process is repeated over the extent of the
sport’s area and left until adhesives are cured sufficiently to allow application of the sand
infill.
Shrinkage and growth of the carpet through varying weather conditions will create
difficulties and contradictions to the joining process. Experience will tell the installer how
much strain to place on the width and length of the carpet while carrying out the laying
process at different times of the day and at different times of the year. In the meantime,
experience is a very difficult thing to teach, but it should be known that a polypropylene
carpet that is joined together in the middle of the day in the middle of a Queensland
summer that does not have looseness or a series of buckles in the areas between widths
will almost certainly have problems with the joins separating either immediately or in later
years. So long as these buckles are not too great, they can be worked back into the
finished surface with the careful application of the sand.
Part of the continuing process of degeneration or aging of the carpet involves shrinkage
which seems to be most prevalent during the onset of the winter months when breaks in
various joins are reported and as mentioned earlier, this is a very labour intensive and
costly exercise to repair. Such problems are less relevant, though still very real in areas
where climates maintain lesser variations throughout the day and the year. The writer is
not sure whether this is an issue that has ever or is currently being addressed by product
manufacturers but confidence in the past performance of polypropylene as a medium for
an economical sport’s surface, both for wear and playability has now been proven. All of
this information is offered to accentuate the importance of proper laying techniques in
achieving a successful long term outcome.
After decisions are made about bases and synthetic grass qualities, and the synthetic
grass is installed to satisfaction the sand application process becomes the most important
section of the court project. As mentioned earlier this is an element that, because of its
Technical Manual 77
heavy and seemingly thankless nature, is too frequently considered a task that must be
endured and completed as quickly as possible. Yet it is this segment that will create the
consistency to ball bounce and footing, therefore enjoyment of the surface throughout its
life.
Because the manufacturing, packaging and transport processes can cause the carpet
pile to be distorted care must be taken to correct the pile-lay during application. The
installation itself of both the carpet and the sand also cause more distortion to the yarn
and is often exacerbated by hot weather conditions. No one method has been refined to
address this segment of the sport’s surface installation, but all are agreed that to
complete the sanding task with all pile over the court area standing erect is the ideal.
The following is a process that has achieved successful installations for over two
decades.
The carpet should be totally dry before commencing the sanding operation and the kiln
dried sand (around 15 tonne = square metre x 1 mm less than the pile height x 1.45) can
be delivered, usually in bulk to the side of the court. Hand work will be required firstly to
“work in” the buckles or looseness caused from “not” stretching the carpet during
installation and secondly to correct the bent or twisted pile mentioned. This is also the
time to marry the base-line sections and any other lines which are installed “end-on-side”
to the general lay of the carpet. After satisfying yourself that these corrections are in
order the sand should be applied over the total court area with the use of a fertiliser
spreader with balloon tyres or wide flat wheels which will minimise further marking or
squashing of the carpet pile.
Only sufficient sand should be applied that will
line the base of the pile to a depth of
approximately 3mm to 5mm. It will be seen
that around half of this first sand layer will
remain on top of the pile and can then be hand
broomed against the lay of the pile so as to
vibrate the sand into position while at the same
time straightening the pile lay. This process
should be repeated sufficient times until the
pile is seen to be erect or before the sand can
be applied more liberally.
This is also a reasonable time to introduce machine brooming. Whichever the machinery
type used it should simulate the hand brooming described above but it is usual that this
more robust mechanical method will compact the sand better than straight hand
brooming usually making for a “settled in” playing surface more quickly. The final finish is
usually produced with a “precision broom” done by hand to best estimate the amount of
sand that will make up the final surface.
Whether paid or otherwise most contractors will return in a three to six month period to
adjust the sand levels, either by adding sand or by taking it away, to suit client
preference. The period can be subject to rainfall (more is better at this stage) since
completion together with the amount of use the court has received. Done correctly and
with regular maintenance no further sand will need to be added for the life of the court
and in fact may have to be removed as the carpet pile reduces in height through normal
wear and tear.
7.3.7 SFAG maintenance

Maintenance of sand levels is the single most important task in achieving consistent
playing characteristics for your sand filled artificial grass (SFAG). While other issues are
important to maintenance, the regularity of ball-bounce and footing are crucial to a
successful sporting surface and whether the chosen surface has been designed for grip
or for slide, it should be consistent. To this end the initial three to six month period of
maintenance is the most crucial to long term happiness with the synthetic grass.
Technical Manual 78
This is most readily achieved with the use of a broom with particular bristle stiffness
similar to that probably used by your contractor during installation. A simple pushing of
the broom up and down the court (best with the net put to one side) will achieve
corrections with each pass as will occasional cross-wise brooming. If this is repeated
regularly (weekly if getting plenty of use) until the adjustment service is due the contractor
will probably have little to do but your court surface and the future enjoyment of it will be
the beneficiary. A commercial centre may choose to mechanise this operation with drag
brooms behind a rider mower or similar, but such a process should always simulate hand
brooming and because of its abrasive nature and that it is more easily carried out, care
should be exercised to ensure that it is not over done creating premature wear.
This weekly chore can be reduced to
monthly (again subject to court use) after the
“settling in” period and can be interspersed
with the use of a Clean Sweep, a propriety
product ostensibly designed as a leaf
sweeper, which assists in maintaining even
sand levels. In some States this action with
the Clean Sweep is an accepted part of the
protocol of the game, dragging/bagging the
court after each match thus leaving a pristine
surface for following players. This would be
a worthy protocol to foster throughout all
Clubs and private courts in all States.
Environmental issues play a large part in the required maintenance of SFAG, with fallout
from trees, algae growing in areas often shaded by trees, overland flow from poor
drainage and general fallout from adjoining industry or the atmosphere. These elements
affect hardcourts, driveways, the roof of your house and in fact most areas of the home,
but are often not noticed on the textured surface of a SFAG court until they (the algae for
instance) are well entrenched.
Although the brooming described may create enough disturbance of the carpet pile to
inhibit various algae growths, there will come a time when it is appropriate to call in
professionals. A healthy maintenance industry exists within the tennis fraternity which
can address all of the above provided that they always bear in mind the important issues
that make SFAG successful.
Unless the carpet has been infiltrated by foreign matter it is rarely desirable to remove all
of the sand from a SFAG surface as any areas so treated will need to go through the
“settling in” period again. Most maintenance firms should be dealing with the top few
millimetres of the surface and if removing sand with other polluted materials, care should
be taken that the original sand levels are returned. They should also ensure that the
treatments necessary on the side of a court do not assist in extending or spreading the
problem across the full width of the court. Equally, cleaning of mechanical equipment
after treatment at one address is important so that pollutants are not carried onto the next
court to be serviced.
Treatment of infected areas by use of gurney or strong water jets should be carried out
with caution so as to not remove an excess of sand which is difficult to replace
consistently. Part of the apparent success of such an operation is emphasised by the as
new “greenness” of the extra pile exposed below the top of the sand which can tend to
mask any remaining algae growth. The use of blowers, although very efficient for leaf
removal must be used with care as they too can remove some sand on each pass which
in turn reduces the pile height and in turn the life of the carpet.
Chemical treatment of SFAG for algae growth has often been handled with the use of
products such as copper sulphate or varying mixtures of pool chlorine and maintenance
firms have their own proprietary anti-algae treatments. Such chemical treatments should
only occur with the approval of the SFAG manufacturer who generally offers a seven year
warranty on his product and great care should be exercised so that the general
environment is not effected adversely.
Technical Manual 79
Maintenance issues can be minimised by careful initial landscape planning through not
planting inappropriate types of trees and not too close to the court (the root systems
delight in ground conditions under SFAG) and the clearing of debris, leaf litter and any
other infiltration. Good base construction through levels which shed water quickly,
particularly in those areas shaded by trees or adjoining structures also assists in lowering
of maintenance effort as will regular disturbance through sand levelling. A plastic lawn
rake can make for hard work in clearing debris from the court but some solace may be
taken in that the tips of the pile are being teased in a manner that assists the “settling in”.
The accepted norm for falls which allow good drainage of a court surface, whether SFAG
or other non-porous synthetic surface types is 0.9% in both directions which on a
minimum ITF court size of 34.77m x 17.10m will create falls of approximately 300mm in
the length, 150mm in the width and 450mm from one corner to its diagonal opposite.
7.4 Synthetic Clay (outdoor carpet) surfaces
7.4.1 Introduction
Synthetic clay tennis court surfaces are a relatively new
innovation into the tennis world, born from a number of
circumstances; primarily the requirement for a waterless,
low maintenance alternative to a natural clay surface.
Products currently available in the marketplace include
POLICLAY, SUPERCLAY, and CLASSIC CLAY
Australia does not have a generic “clay court surface” like Europe and the Americas. EN
TOUT CAS and RAW COURTS surfaces are the closest relatives, however they are
constructed from a fired terracotta product and generally if kept in optimum condition are
somewhat faster than the real clay surfaces. They also require a considerable amount of
maintenance and consume significant quantities of water to keep them at optimum
playing condition.
Ant bed, granitic sand and other localised “sand type” surfaces are also available using
locally available raw materials. Generally these types of courts are installed at entry level
with budget prices and are usually not suitable for serious competitive tennis.
Synthetic clay surface is designed to replicate the playing characteristics of real clay,
being a slow to medium pace and forcing players to “construct points” using the full
variety of stroke play.
A well constructed synthetic clay court will play and
slide like real clay and replicate playing conditions
both dry and wet, without the requirement for water
and daily, monthly and annual maintenance.
White marking lines are “tufted in” to the surface
providing permanent lines and eliminating the
requirement for periodical line repair and
replacement.
Weeds and grasses will not grow in a well
constructed synthetic clay court.
Player comfort is much greater than most current high class surfaces, as the dynamic
granitic type finish provides a built in softness underfoot (noting that some surfaces are
softer than others and this should be researched by the potential client).
The softness allows extended periods of play minimizing potential impact damage and
other related sports medicine issues.
Synthetic clay is environmentally friendly, replacing the need for considerable water
usage.
No water is needed for play or maintenance on these surfaces.
Technical Manual 80
7.4.2 Construction
Various methods of construction can be used for these courts, each with pro’s and con’s
similar to those of sand filled artificial grass courts already discussed in this section.
7.4.2.1 Concrete Base

Site determined as suitable. Information provided in Section 6.6 above should be
considered when constructing a concrete base for a synthetic clay surface. The
subgrade should be expertly excavated with all unsuitable material removed.
Subgrade stabilized, compacted and graded to drainage falls of approximately 1%
transversely and longitudinally draining to one corner of the court(s).
Use laser controlled grading equipment to ensure uniformity of subgrade and
consequently uniform slab thickness.
Alternative levels may be used however remember the golden rule “less fall….longer
draining…less play”.
Concrete should be finished with a helicopter trowel.
Incorporated into the slab should be the footings for tennis net posts. These should be
poured as part of the slab and be appropriately engineered as described in Section 10.
Also incorporate shallow dished spoon drains, expansion joints and kerbing etc as
necessary.
7.4.2.2 Asphalt
Refer to Section 6.5 above for detail of asphalt
base construction.
Court perimeter edging may be either bricks
laid on concrete footing, concrete kerb or
treated timber plinth. Various designs are
available.
Install a compacted crushed rock base, using
selected suitable fine crushed rock with a
maximum particle size of 20mm with
appropriate mix of fines.
Grade the rock using a motorized laser controlled grader to ensure uniformity and correct
levels.
Water crushed rock during placement to ensure optimum moisture content.
Compact using a motorized twin drum roller with minimum static weight of 3 tonne.
Achieve a 95% compaction as per Australian Standards.
When rock placement is completed the finish should be dense and uniform, basically
impervious with level tolerances no more that 5mm when measured with a 3 metre
straightedge
Supply and install a hot mix machine laid asphalt layer, using a self propelled paving
machine.
Asphalt shall be laid to provide a design layer of 30mm compacted thickness.
Asphalt shall be 7mm BCF grade.
Asphalt should cure for a minimum of 10 days before any surface is applied so as to void
bituminous vapours and oils etc.
7.4.2.3 Drainage
Both concrete and asphalt provide a horizontal drainage system, whereby all water drains
off the surface not through it.
Technical Manual 81
7.4.2.4 Crushed Rock
A crushed rock base is constructed as previously described however if no asphalt is to be
applied, the surface must be finished with a 5mm crusher dust or manufactured granitic
sand product to give a finer surface finish.
Needless to say that the levels are much more stringent than when installed as a base for
a final asphalt layer, as this will be the finished base and any imperfections will show
through to the completed surface.
The crushed rock alternative where used can be either impervious to water or fully or
semi porous allowing vertical drainage. The design will depend upon local sources of raw
materials and the design brief.
7.4.2.5 Conversion System

A conversion system can be used when converting an existing En Tout Cas tennis court
to a synthetic clay court.
• Remove tennis court lines and nails
• Rotary hoe the entire area to a depth of approximately 100mm
• Check subsurface drainage system is operative and in good condition. If not
replace with a new system laid in a herringbone pattern and connected to mains.
• Laser grade surface introducing a crushed volcanic rock like scoria to augment
court drainage if necessary.
• Compact surface with a twin drum roller whilst laser grading
• To the prepared base supply and install a manufactured granitic sand 5mm minus
porous product as the final layer. Laser grade and compact. Hand finish as
necessary.
• This provides a vertical drainage system for the new court.
7.4.3 Synthetic Clay Surface

Installation and manufacture methodology is different for each product. However, these
surfaces generally consist of a synthetic fibre carpet made from either polyethylene or
polypropylene fibres, with differing pile weights and lengths
The white lines are made of the same fibres and are “tufted in” during manufacture of the
carpet.
All joins are held using specialist adhesives and backing tapes.
Once the carpet has been laid by suitably qualified installers the “clay” surface is applied
mechanically in various fine layers and groomed well into the fibres.
The finished level of the clay should be approximately 2mm above the carpet base.
Groom the surface to ensure correct coverage and uniformity.
7.4.4 Maintenance
The court will require an initial “playing in period” of approximately 30 days during which
time weather and playing will further settle the clay. Occasional odd bounces may be
experienced during this time.
At the expiration of this period the court should be re-groomed with further clay applied as
necessary.
Once fully groomed, the court can be handed over to the client.
Ongoing maintenance shall be light brushing of the lines using a rotary line sweeper.
Grooming of the surface with a drag mat to provide minor levelling and uniform surface
material distribution is necessary. The frequency of this is by personal choice however
indications from court owners suggest once prior to each match is sufficient.
Technical Manual 82
The court may require up to 300 kg of coloured sand per year to replace that lost to
erosion. This is a minor expense.
The industry is confident that the surfaces will provide up to 20 years of play before any
major refurbishment would be required.
7.5 Natural Grass Tennis Courts

Grass tennis courts when constructed properly, provide the fastest surface on which
tennis is played.
The surface provides for a “serve and volley “game where the ball bounce is low and fast
and the speed can be adjusted by means of rolling, raising or lowering the height of cut or
moisture control or a combination of all of the above.
The grass court however must be maintained on a daily basis to obtain the optimum
performance whether it is for a Davis Cup Tie or a social hit.
This section outlines in a “layman’s language” the minimum standards to construct and
maintain a grass court. It is to be used as a reference only.
A thorough and detailed planning of the project scope of works should be undertaken
before construction begins to ensure all information is available and correct.
Areas covered below are:
• Construction
• Grass types
• Equipment
• General Maintenance
• Usage
• Preparation- Social/Competition
• Renovations
• Drop in Courts for Davis Cup Ties
7.5.1 Construction
Before construction commences it is important to choose the correct site and to have the
necessary permits, and detailed information and plans in place.
A Northerly aspect for court orientation is advised to minimise sun in player’s eyes
Construction of the court involves:
• Excavation of site
• Forming a sub base with a slope of 1:100. Base must be a clay compound and
glazed to assist with water flow
• Drainage- 100mm slotted agricultural pipe every 5 m in an e-w or diagonal design
with a 1:100 fall and a main out let to a sump pit located off the court. Also have a
drain at the northern end of the court to assist with water run off from the covers
• Main to be larger diameter if possible
• 7-10 mm pea gravel, in the bottom of the trench and 100mm deep over the level of
the trench and laser levelled to 1% slope n-s
• Edging of concrete surrounds if applicable should have a final level 25mm below
court surface finished level
• USGA spec sand 50mm deep
• 200mm of soil (clay loam 25% clay content) this should be checked by laboratory
analysis before ordering. This is then layered in 50mm layers laser levelled and
Technical Manual 83
rolled with a 1ton roller until 200 mm final layer is laser levelled and rolled to
consolidate
• Laser levelling to be with a fall n-s with a +- 1.5mm variation an final grade of 1:100
is recommended
• Washed turf suitable for court usage laid and watered/fertilized regular until turf
established
• Surveying of the site for lines/post layout/nets fences/lighting (use a good reputable
survey company)
• Installation of net post sleeves/centre tie down
• Installation of fences/lighting
• Installation of irrigation/watering points
Sleeves for net post should be concreted in at a slight angle (.5 of a degree) outwards to
allow for tension forces of the net and also be set below level of finished playing level so
not to damage machinery.
Post sleeves should be embedded in concrete 1 m deep by 300mm wide.
Sleeves should also be capped when not in use
7.5.2 Grass types

There is a variety of turf available today that would be suitable for tennis courts.
Some of these are:
• QLD blue couch
• Conquest
• Greenlees park in warmer climates
• Legend (although obtaining a pure strand of this variety is an issue at the time of
writing)
• 328 variety
There are always new varieties being bred, so these choices will change over time once
the newer varieties have proven themselves.
7.5.3 Equipment
To obtain the best surface for the grass court the following equipment should be
purchased:
Depending on the number of courts the following is the minimum for one court
• Cylinder type mower with 11 blades i.e. Toro 1600. John Deere 220, preferably
with grooming reels for de-thatching
• Battery powered Line marker i.e. Supa turf
• Roller 1.5 tonnes max
• Squeezes/Supa -sopper
• Small fertiliser spreader
• Small sprayer
• Covers and sand bags
• Edger
• Level lawn
• Wheel barrow and shovels
Technical Manual 84
• 19mm hose with fish mouth nozzle and soaker connection
• Scarifier
• Polishing dew roller with weights
7.5.4 General Maintenance

Maintenance of the court is all year, with the start of the season and finishing with a
renovation in spring / summer in preparation for continued use through the year.
Maintenance involves different routines depending on levels of play. For major
tournament play such as Davis Cup or state and major championship play, this will
involve intensive turf management.
For social play the level will not be as severe.
Maintenance required for both social and major tournaments involves the following:
• Mowing
• Rolling
• Fertilising
• Spraying chemicals for pests and diseases
• Repairing base lines, nets, line marking
• Light “dust ins” and general court maintenance
7.5.5 Usage
Depending on the type of use the court should be rotated or rested on a regular basis.
If the use is for social ply only the court should be rotated more and HOC should be
raised to accommodate the level of play. It is important that committees understand that
the turf will not hold up with constant usage and damage to the surface or excessive wear
could result in a poor performing court when the time arises for it to be used for
championship play.
It is also important that sufficient time be allocated for court(s) to recover from
renovations.
For major tournaments, allocation of certain courts and a time regulation should be
utilised.
The main court should NOT be used for practice until the finals with the exception of
restricted time generally no more than 1 hour for teams to familiarise themselves with the
characteristics of the court.
The practice courts and the main court should be maintained the same with no deviation
in preparation.
7.5.6 Preparation - social/competition

The Height of Cut (HOC) for social play can be as high as 8mm to allow for the surface to
withstand high usage. If possible allow a day between cuttings and lightly roll to maintain
good even bounce.
Vary the direction of the cut to prevent “grain” from becoming set.
For championship play the HOC is usually around 4-5mm or lower depending on the
event, and the speed of the court. Mow in a N-S direction
The application of a nitrogen / iron fertiliser will provide more skid of the ball and a quicker
surface a week out from the event.
Rolling and watering the courts can be used to find the balance leading up to the event to
find the right amount of bounce for players.
Technical Manual 85
Davis Cup Preparation is unique as the home team can dictate the type of surface it
requires and this is reflected in the court preparation.
7.5.7 Renovations
At the end of the playing season or around spring/summer the court(s) should be
renovated.
This involves
• Taking a soil sample and testing for nutrient deficiencies
• Scarifying the surface to remove thatch build up.
• Coring the surface to allow air entry and allow granular fertiliser to enter the profile
• Topdressing using the same medium as constructed. This is very important.
• Laser Levelling if required
• Rubbing in the top dressing material with level lawns
• Fertilising based on a soil test result
• Applying chemicals to control pests/diseases
• Bring into play over 4-8 weeks depending on situation and usage requirements this
involves lowering the HOC and light rolling, watering and finally reline marking
There is no substitute for a good renovation and taking short cuts is not advisable for long
term playability of the court
7.5.8 Drop in courts

In recent years the Strathayr Company in conjunction with Tennis Australia has
developed a portable drop in court.
This involves the use of mesh elements and a drainage system combined to allow
portability around the country for mainly Davis Cup ties if they are to be played on a
natural turf court over artificial court.
• The squares are 2.4m x 2.4m (6m2) 200mm deep and weigh 1.7 tonnes.
• The soil is 150mm deep and is reinforced with mesh reflex elements squares fit
together by forking into place.
• A court consists of 160modules and each module is numbered for a perfect fit.
This system allows the surface to be placed into position within 12 weeks.
7.5.9 Irrigation
Installation of an irrigation system will provide correct amounts of water to the court
The Toro 2001 series sprinklers are ideal for single courts.
To install a Toro 2001 series on a single court will require 2 X half circle sprinklers and 4
X quarter circle sprinklers
For double courts the system can be configured to run independently for a two-court
application. This will involve upgrading or installing a controller with sufficient stations to
cover two courts.
A main controller with at least 4 stations will also be required.
As with all irrigation systems connected to the mains water supply, there needs to be a
back flow prevention device. Generally a dual check valve is sufficient, but check with the
local Council for their requirements.
Companies with trained staff with irrigation installers licences are available in Qld to
install such systems. One company is TIS (Turf Irrigation Systems) at Capalaba in
Brisbane’s eastern suburbs.
Technical Manual 86
Generally to install a system on a single court will cost around $4,500.00 (as at the time
of writing).
If a club wishes to do the installation itself, be sure that the person installing the system
has the restricted plumber’s (irrigation installer’s licence).
7.5.10 Grass court maintenance

Grass courts require maintenance throughout the year.
This will ensure
• A firm surface that provides good traction for players
• An even bounce of good height
• Even density and colour
• Good presentation of the court being weed, disease and pest free.
After renovation the following maintenance is generally undertaken, and can be broken
down into seasonal requirements.
N.B: Please note that the seasonal months submitted here are related to central Brisbane
and are related to on site weather station readings collected over a period of time. It is
important to remember that these can and could change. It is advisable to check local
conditions and make necessary changes to individual clubs programs
SUMMER Season in QLD: December – Early March
Mowing: In general remove only a third of the leaf and mow only when surface is dry.
The court should be mowed at least every second day, which will provide a tight surface.
In some places mowing daily will need to be carried out.
Hoc will be around the 4 to 8mm area depending on use and competition.
It might be required that the court be double cut on occasions, depending on growth.
Be sure that the blades are regularly sharpened by back lapping the cylinder with grinding
paste.
Irrigation should be applied deep and infrequent and ideally should be applied based on
ET rates for the area. Root depth also needs to be taken into account when doing this.
7.5.10.1 Spraying
A person with an appropriate chemical licence, such as “Chemcert” or “ACDC” should
undertake the application of any hazardous chemicals. The individual club should also
have a chemical distribution licence. The chemicals should also be applied as per
manufacturer’s recommendations.
Applications of fungicide for diseases relating to summer months will need to be applied.
These diseases can be either root or leaf and appropriate fungicides will control or
eradicate any outbreaks.
Spraying for pests such as armyworm, couch mites, couch fly, and black beetle can be
controlled with appropriate pesticide chemicals.
Applications of herbicides can be undertaken throughout the season, but best applied
before renovation to allow the turf to recover.
7.5.10.2 Wetting Agents

Wetting agents are applied when the profile needs an even wetting up or where there is
lack of sufficient rainfall to evenly wet the profile.
Technical Manual 87
7.5.10.3 Fertilising:
Before starting a fertiliser program it is important to obtain a soil and if possible leaf
analysis of the court to determine the exact nutrient requirements and deficiencies and
correct these before going into a maintenance program.
Soil tests should be conducted at least twice per year to gauge soil and plant
requirements.
In general after renovations, a fertiliser higher in phosphorus should be utilised to
establish the root system and also enable the addition of organic fertiliser into the profile.
Regular fertilising with a mixture of Nitrogen and Potassium ratio of 2:1 will ensure good
recovery from wear and produce lateral growth, as well as maintain the colour and speed
of the surface.
It is also important to add trace elements as required, but soil tests will indicate any
deficiencies.
Turf specialist companies such as but not limited to- Globe, Nuturf, Simplot, T&I and
Floratine have a range of fertilisers to suit requirements for closely cut turf.
The fertiliser can be applied in granular or in liquid form.
In all cases of fertiliser application, the directions of application on the label should be
adhered to.
The ratio will then drop from 2:1 to 1:1 from late February to prepare for colder months.
With the profile being mainly clay it is important to consider the application of liquids and
foliar fertilisers to assist with maintaining a dryer profile leading up to games.
All companies have a folia range and these should be examined to ensure that the
correct product is applied.
Winter Season in QLD –March to September
Fertilise with a ratio of N: K 1: 1. And in colder areas a ratio of 1:2 could be considered.
This will enable continued recovery of the baseline and provide sufficient nitrogen to
maintain growth.
Be careful to watch the nitrogen component of the product to ensure that it is not too high.
Adding sulphate of iron (chelate type) and magnesium sulphate will assist with colour.
7.5.10.4 Mowing:
Mowing to be carried out to remove one-third the leaf tip generally, but again local
conditions can change this to everyday if temperatures increase top growth. Mowing
twice per week should be considered where temperatures are in the colder regions.
Raising the HOC a millimetre or two will provide better protection to the surface from
excessive wear
Irrigation again depends on ET rates but generally less than for summer months
7.5.10.5 Dethatching and aeration

During the summer months a regular dethatching program should be undertaken to limit
the amount of thatch build up and lateral growth, which left unchecked, will result in a
slow court and “spongy” surface.
The operator will need to judge when the use of this machine is needed.
The use of a pedestrian scarifier or use of the dethatching vertical blades on the reel
mower will remove sufficient thatch. It is important not to allow the blades to bring up soil
as this will result tin the surface taking too long to recover and will leave unsightly lines.
Generally set blades 1mm below HOC.
Technical Manual 88
Aeration usually involves the use of a “vertidrain” with 8mm tynes. Again the manger will
need to access the frequency and tyne selection relevant to court usage and what he/she
wishes to achieve by using this practice.
7.5.10.6 Topdressing / "dust ins"

Application at renovation of the same medium as the profile to top dress the court will be
required. The medium should be dry if possible to allow ease of application. Once applied
the surface is rubbed in with level lawns to ensure good surface contact.
Periodically the court can be “dusted" using a sieved material to lightly cover the court to
assist with wear recovery particularly on the base line and centre areas.
7.5.10.7 Rolling
Rolling of the court should be undertaken to firm the surface not to make the surface
“rock hard”.
In the summer months when the surface has a lot of “grass” the rolling can be done
frequently. It is important to finish by cross rolling to eliminate lines from the roller.
Rolling with the playing court first then finishing by rolling across court will ensure that
there is no deviations in he surface that will affect the balls bounce.
Double rolling, that is coming back on a slight angle along the first line of the roll, will also
help with this.
Always take into consideration the condition of the soil. If the profile is too wet, rolling may
cause ridging and if too dry it will be a waste of time.
Roll outside the playing area first if ridging is a concern and inspect before proceeding.
The amount of rolling will determine how high the ball bounces and generally for social
competition a bounce from knee to waist height is ok.
Roller weights should be 1 tonne and 2 tonne rollers
7.5.10.8 Spring (Renovation Season) - October to December

Renovation should be carried out at the end of the season and will involve the following
practices:
• Scarifying of surface and clean up
• Aeration (coring)
• Fertilising with amendments
• Topdressing
• Watering
• Bringing into play by light rolling and reducing HOC to a playing HOC
Refer to previous section
7.6 Compacted earth bases
7.6.1 European Clay
7.6.2 Introduction
There has been a lot of discussion in recent times about the need for juniors to be trained
on European type clay courts. Most top coaches agree that training on clay courts
provides benefit for aspiring young players. The need to ‘work’ for a point builds strength
and endurance, whilst cultivating a strong technique.
The downside for clubs and users is that a clay court requires more maintenance than
hard courts and synthetic grass courts. Do the advantages of clay courts outweigh the
maintenance problems?
Technical Manual 89
There is not much doubt Australia needs to maintain and /or build a number of clay courts
throughout our country. However there needs to be recognition that for a clay court to
remain in top playing condition, regular maintenance is required. In years gone by, most
of the courts in Australia were loam, ant- bed or en-tout-cas. A number of great
champions grew up on these surfaces.
7.6.3 Construction of a European clay court

A true European style clay court is a combination of crushed fired clay products, i.e. red
bricks and tiles. The secret to a successful surface lies in the correct crushing of the
product to meet geotechnical curves that will ensure binding of all grades of materials.
Consideration for construction of clay tennis courts include:
• Proper base preparation to ensure correct drainage is achieved. This generally will
consist of crushed rock materials incorporating both end to end and side to side falls to
side drains. Subsoil drainage beneath the actual court surface is normally not
required.
• Sourcing and supply of correctly graded ash drainage bed
• Sourcing and supply of consistently crushed ‘clay material’, screened to remove
impurities from product
• Laser levelling surface products to achieve optimum playing surface
• Construction of border around tennis court to retain clay product – options include
bricks, blocks, formed concrete border, machine laid continuous concrete kerb
• Installation of fence, including either a raked opening or double gates to allow easy
access to court for rolling
• Installation of lights to be carried out prior to installation of surface, if court perimeter
restraints require a cherry picker to be taken on to surface
• Installation of removable net posts to make the rolling of surface easier
• Installation of centre anchor flush with court surface for ease of rolling surface
• Irrigation system – ideal is overhead or pop-up sprinkler system
• Line system
• Maintenance equipment – roller, bag, broom for lines, screed or levelling lute for
product
• Maintenance program
7.6.4 Choosing a constructor

Each court builder will have a proven method for construction of clay tennis courts in
accordance with the type of product they install. Investigations prior to choosing a court
builder should include
• Ensuring builder is licensed and fully insured
• Their ability to provide references and details of past and current works so that these
sites can be visited
• Provision of detailed scope of works so that true costs of finished project are
established.
7.6.5 Equipment for surface maintenance

The following items include every piece of equipment involved in maintaining a clay court:
• Mechanical roller or
• Hand roller or
• Towable split drum roller
Technical Manual 90
• Timber court screed
• Clay grooming rake
• Clay packing hammer
• Smooth bristled broom or line sweeper for lines
• Light net bag
• Timber rubber squeegee
• Watering system
• Aussie clean sweep
• Calcium chloride and spreader
• Light aluminium grain shovel
• Wheelbarrow
• Irrigation system
A single residential clay court would only require an irrigation system, a broom for
sweeping lines, a roller [towable or hand roller], light net bag, and a timber court screed.
A multi-court commercial clay court centre would be best to have:
• an irrigation system
• a mechanical or towable split-drum roller
• light net bags for each court
• line sweeper for each court
• a timber court screed.
It would be up to the individual club to decide the extent of ongoing maintenance they
undertake, then other equipment like shovels, calcium chloride, and the like can be
considered for purchase, or the court builder can provide an ongoing maintenance
service using his own equipment as required.
[Calcium chloride will reduce the amount of watering required in hot weather].
7.6.6 General Maintenance

Maintenance of the court is ongoing, and maintenance levels required are dependant on
court usage and weather conditions. Maintaining your clay surface requires a regular
program to ensure optimum performance, and to extend the life of the court. The
procedure involves bagging, watering, sweeping and rolling the surface in accordance
with court usage.
CLAY COURT MAINTENANCE SUMMARY
Procedure Schedule
Timber screed Inspect court, repair divots and clear court of any debris
Bagging Use only the light net bag.
Frequency: daily and after play, parallel to net and
lengthwise. Alternate the direction of bagging.
Sweep lines 1. Before watering so dust does not settle or stick to
lines when watering.
2. Before rolling, so roller does not damage lines, and
avoid turning roller directly on lines
Technical Manual 91
Water Nightly and early morning, plus midday during extreme
heat.
Allow water to penetrate material before rolling
Rolling Each day before play to help bind clay material.
After heavy rain once water is drained.
It is important not to over roll the surface. Too frequent
rolling will cause delamination of surface.
Refer to the rolling pattern diagram for correct rolling
procedure – overlapping the rolling pattern will avoid
steps in surface.
Once a month roll court in both directions, i.e. cross
court and lengthwise
Bag again Bag court in both cross-court and lengthwise directions
Sweep lines again Court is ready for play
7.6.7 Using Maintenance Equipment
7.6.7.1 Mechanical roller or towable split drum roller

A mechanical roller is the fastest and most efficient way to groom the court. It is best to
alternate the pattern of rolling the court. Use a smooth driving action, and do not turn the
roller sharply, as it may twist the surface and damage the lines.
Repair any divots, bag the court, and sweep the lines before rolling.
It is best not to roll the court when courts are wet, as the roller will pick up too much
product, and rolling may result in an uneven surface. However, if courts are in use, and
play is interrupted by heavy rain, it is advisable to roll the courts before players return
once surface water has dissipated, and the court is firm when walked on.
7.6.7.2 Hand Roller

A hand roller is useful to quickly roll over smaller patches of the court, particularly
between matches when the areas of play may need a quick bagging and rolling to
stabilize the surface.
7.6.7.3 Timber court screed

Use to repair divots. The timber court screed
levels out product where it is loose and fills
hollows.
Technical Manual 92
7.6.7.4 Clay grooming rake
Use the clay grooming rake to rough up surface for
repair after heavy rain to mix ‘fines’ in with 3mm clay
material. The rake does not need excess pressure
to be effective. The motion for use is similar to
sweeping with a broom.
7.6.7.5 Smooth bristled broom or line sweeper

for lines
7.6.7.6 Light net bag
The light net bag is the only bag to be used on the

surface for everyday scheduled court maintenance,
and maintenance of surface between matches.
Proprietary equipment
The Aussie Clean Sweep is only to be used to
remove heavy debris from surface. Pass Clean
Sweep over surface once to remove leaves,
gumnuts, etc where trees surround court.
7.6.7.7 Watering
Keeping moisture up to your clay court is one of the essential steps for top playing
performance and a long lasting product.
Watering can be achieved via an automatic irrigation system, or just a hand held hose [at
least a 20mm hose to decrease watering time] Either system will work as long as there
is even coverage of the complete surface. Do not hold hose or sprinkler in one spot for
too long.
During summer, when hot and dry conditions are present, you will need to water the court
early in the morning, at midday, and in the evening. Maintaining the presence of the
‘fines’ on the court surface is paramount. The ‘fines’ bind the other layers of product, and
adequate watering will ensure these do not blow away.
During winter or cooler/wet conditions it may not be necessary to use the watering
system. Scuffing different areas of the court lightly with your shoe can test the moisture
content of the court. The material underneath the surface should be darker and moister
than the surface above.
It is best to let the water soak into the court for at least 15 minutes before bagging and
rolling the court.
Technical Manual 93
7.6.7.8 Court hire
It is essential to rotate the court hire pattern of the clay courts at a centre. Generally
players will always want the court closest to the clubhouse or facilities etc; however the
load of court hire must be shared evenly over all the available clay courts at a complex.
7.6.7.9 Coaching
Excessive squad training on clay surface is not recommended. Avoid repetitive drills or
exercises that can be performed on ovals or on other court surfaces, especially if they are
not part of specific clay court coaching.
“Smooth” tennis shoes to be worn. Ideal shoes are clay court shoes, Dunlop Volleys, and
shoes with herringbone sole. Do not allow sports shoes with definite heel or chunky
patterns, as they will dig up court surface.
Educate court hirers that at the end of their hire period they are expected to bag the court
and sweep the lines ready for next court user.
7.6.8 Decomposed granite

Many of the general characteristics, construction considerations and maintenance
procedures for decomposed granite courts are very similar to those of true clay courts.
The most obvious difference is the final surface layer of these courts is comprised
predominantly of highly crushed particles of granite rather than clay particles as in a
traditional clay surface.
The advantage this product has over traditional European Clay materials here in Australia
is the ready availability of a relatively consistent product throughout the country. There is
even a degree of flexibility available with regards to colours this material can be supplied,
with the product able to be coloured prior to delivery and installation – very much like the
materials used in the USA to produce their equivalent Fast Dry / Har-Tru surfaces. A
recent popular development is to produce decomposed granite in traditional green to
reflect a grass court or red to imitate
European Clay.
An example of this innovation can be seen
on the pictures provided at right. The first
picture is of an existing decomposed granite
court that was in need of reconditioning. This
court has then been resurfaced with green
coloured decomposed granite, resulting in a
far more aesthetically appealing finished
product, as per the second photo of this
court.
As with European Clay courts, there are a
limited number of contractors capable of
constructing courts of this nature and only a
contractor with a demonstrated track record
with these surfaces should be considered.
Similarly specialist maintenance equipment
and periodic maintenance routines will be
required to keep these courts in optimum
playing condition. Given recent introduction
of severe water restrictions in many parts of
Queensland and eastern Australia, the
amount of watering these courts require to
keep them in this condition should be seriously considered, along with the time required
to undertake regular maintenance activities before any decision is made to install a
decomposed granite, or any other form of natural clay court surface.
Technical Manual 94
Equipment photos – courtesy of RAW Courts
Technical Manual 95
8 Fencing
8.1 Introduction
Fencing provides two basic functions, to retain balls on the court during play and to
provide security for the court and equipment when unattended.
Fencing design is predominantly metal pipe posts, with or without rails, supporting chain
mesh. Within this broad description a range of specification elements can be changed for
functional, aesthetic or cost considerations. Other fence styles include timber structures
with chain mesh, thatched fencing, masonry walls, etc. As the vast majority of fencing
structures for tennis courts consist of a metal pipe framework and chain mesh, this
manual will focus on elements of that design.
The dimensions of the fenced enclosure are
covered in Section 4.5.1 in this manual. Where
a minimum court size is chosen, the fence
structure should be outside these dimensions.
As the primary function of the fence is to retain
balls on court, important issues include the
height of the fence, the size of the chain mesh
“diamond”, and the height of the gap between
the bottom of the fence and the court surface.
Another important area for retaining balls on the
court is the access gates. These issues are
addressed below
Fence structures may abut or include other court elements such as retaining walls, hit-up
walls, light towers, etc.
Tennis Queensland highly recommends that all court fences should have truncated
corners where possible, as this design feature not only saves money, but also eliminates
“dead spaces” in corners of courts where out of play tennis balls often end up and can
also serve as an excellent court entrance point.
An Australian Standard is currently being developed that will include a specification for
tennis court fencing.

Bottom Rail Horizontal rail strengthening the bottom of the fence to prevent
balls rolling under the fence and prevent the mesh bowing out and
drawing up from damage caused by impact of players.
Chain Link / Chain “Diamond” pattern wire fabric used for fencing.
Mesh
Diagonal Length of pipe attached to a post and anchored to the ground at an
Stay/brace angle of approximately 45 degrees. This is typically used to
provide support to the corner posts to ensure they are not pulled
over by the strain of the chain mesh.
Diamond Size Measurement of chain mesh using the dimension between the
parallel wires of a diamond
Dividing Fence Fence dividing courts where a bank of courts is in place.
Double Galvanized Highly corrosive resistant chain mesh.
Helicoil Tightly coiled spring steel used to provide additional horizontal
support for chain mesh fencing to resist damage to the chain mesh
caused by impact of players.
Intermediate posts Posts along a fence line excluding the corner posts.
Technical Manual 96
Knuckle Bend in wire at the edge of the roll.
Lacing Wire wrapping used to attach the chain mesh to the top rail.
Nominal Size Dimension of pipe in terms of its diameter.
(“Nominal Bore” or
NB)
Perimeter Fence Fence surrounding a tennis court to retain balls in play.
PVC Coated Galvanized chain mesh that has been coated with coloured PVC to
improve the appearance and the moisture resistance of the chain
mesh.
Selvedge Natural edge of chain mesh as delivered.
Slope Downs Describes the section of top rail where a fence height changes, for
example, from 3 metres to 1.1 metres.
Strainer Wires Wire used to provide additional horizontal support for chain mesh
fencing to resist damage to the chain mesh caused by impact of
players.
Top Rail Horizontal rail supporting the chain mesh at the top of the fence.
Truncated Corners Fence corners that have been finished with a 45 degree panel
rather than square corners.
Wall thickness Strength of pipe as determined by the thickness of the metal wall.
8.3 Metal fencing

Metal fences are generally constructed of round pipe posts and rails with the chain mesh
supported and/or strengthened with horizontal strainer wires.
Pipe used in the construction of metal
fencing is specified by the diameter of the
pipe and its wall thickness. Popular pipe
sizes used for posts include DN100, DN80,
DN65, DN50 and DN40. These
classifications represent (approximately)
an internal diameter (previously known as
“nominal bore” or “NB”) of 100mm, 80mm,
65mm, 50mm and 40mm respectively.
DN32 is used for top and bottom rails.
DN40 pipe is used for bracing. DN25 is
used for gate frames. Other things being
equal, the greater the diameter of the pipe
the stiffer and stronger the pipe is.
A second specification used to describe pipe is wall thickness. For a particular grade of
pipe, the larger the diameter the greater the wall thickness. The table below shows the
relationship between pipe diameter and wall thickness for a particular grade of pipe
(medium quality) used for posts.
Nominal size Outside Wall

DN Diameter Thickness
(OD)
DN100 114.3mm 4.5mm
DN80 88.9mm 4.0mm
DN65 76.1mm 3.6mm
DN50 60.3mm 3.6mm
Technical Manual 97
Light quality pipes are used for bracing and rails are dimensioned as follows:
Nominal size Outside Wall
DN Diameter Thickness
(OD)
DN40 48.3mm 2.9mm
DN32 42.2mm 2.6mm
Fence components have a limited life. This can be extended with routine maintenance
but provision should be made in the budget to replace fence components over time.
The main problems facing fences as they age are:
• Stretching of chain
mesh caused by players
running into it.
• Breakdown of
galvanizing, PVC,
powdercoating and
other coating resulting in
rusting of fence
components.
• Stretching of strainer
wires, ties, etc allowing
chain mesh to sag.
• Loosening of bolts and
fittings.
• Gate fittings such as hinges loosening, causing gates to sag and damage court
surfaces; preventing locks from engaging; etc.
8.3.1 Fence height

Standard perimeter fencing is generally 3.0m high or 3.6m high. These heights conform
with standard chain mesh sizes.
Clubs and schools generally prefer fence heights of 3.6m while domestic and resort
courts generally have fences to 3.0m in height.
Where banked courts are constructed with dividing fences, dividing fence heights of 1.2m
or 1.8m are popular.
Higher fence heights will retain more balls but will cost more. Typically, a 3.6m high
fence will cost an additional 10 percent. Where a court is used by less experienced and
younger players and/or it abuts hazards such as highways or situations where balls may
be lost, the higher fence is recommended. Lower fences are less intrusive aesthetically
and generally recommended for domestic or resort courts.
8.3.2 Post installation

Fence posts are concreted into the ground. On some installations, such as roof tops,
posts may be bolted to the court base with masonry anchors.
Corner posts generally have a deeper footing than intermediate posts.
Typical footing dimensions are as follows:
Placement Depth Diameter
Corner Post 900mm 250mm
Intermediate Post 750mm 250mm
Diagonal Brace 750mm 250mm
Gate Arch 750mm 250mm
Technical Manual 98
Where concrete slab construction is employed for the court base, the fence is generally
constructed outside the slab [see photo]. Placing fence posts inside but close to the edge
of the slab can lead to “break outs” occurring at the post. This is caused by shrinkage of
the concrete during curing, differential thermal characteristics of the post and concrete,
vibration and shock when court users hit the fence, etc.
Where a top rail is not fitted, all posts are fitted with a cap to prevent water ingress.
8.3.3 Post size and spacing

Several standards are adopted for fencing depending on the application. Stiffer, stronger
fences are constructed for commercial and club applications as they tend to be subjected
to greater and rougher usage.
Medium grade pipe is used for posts.
Where top and bottom rails are installed fence posts may be smaller as the structure is
strengthened by the bracing effect of the rails. Other forms of bracing are used, including
horizontal braces between the corner post and the next post on each side and diagonal
braces from the corner post to a concrete footing in the ground.
Fence posts are spaced equally along the side or
end of the court. A spacing of 3.3m is regarded as
the maximum allowed for sound fence
construction.
For a fence with a top rail, DN65 posts are used for
the corners and DN40 for the intermediate posts.
Where a top rail is not provided, DN80 posts are
used for the corners with DN40 intermediate posts.
If windscreens or sightscreens attached to the
fence structure are contemplated, then posts and
footings should be designed to accommodate the
additional loading placed on the structure in storm
and other high wind conditions.
8.3.4 Rails and bracing

Top and bottom rails serve both structural and functional purposes.
The primary role of the bottom rails is to provide a neat finish to the bottom of the chain
mesh that will stop balls from rolling under the fence. A correctly positioned bottom rail is
maximum 50mm above the court surface. While trapping a ball, this will allow leaves and
other debris to be blown/ washed off the court. A fence without a bottom rail will often
trap this debris.
Another purpose of the bottom rail is to strengthen the area of the chain mesh that is
most abused. That is, the area from the ground to about hip height. When installed with
a top rail, the chain mesh is attached to the top rail, laced to the bottom rail and then the
bottom rail is strained down and fixed. This tension between top and bottom rail
increases the service life of the chain mesh.
The top rail is an important aesthetic feature and most domestic and resort courts feature
a top rail. Although it does not contribute to retaining balls on the court, the top rail plays
an important role in supporting the chain mesh. The top rail also braces the posts,
particularly the corner post, strengthening the fence structure.
Attaching chain mesh to the rails is an important part of fence construction. Top rails are
generally laced, with the lacing attaching at least every second diamond. Bottom rails are
tied, again at least at every second diamond. Each tie should be twice around the rail
and the pigtail should be on the outside top of the rail and pressed flat so that it does not
present a scratch hazard to court users and others. Bottom rails are tied rather than
laced due to the difficulty lacing a rail so close to the ground.
Technical Manual 99
8.3.5 Bracing and strainer wires
During the installation of the chain mesh, the mesh is stretched and laced to the corner
post. This places significant stress on the corner post and can cause it to deflect, despite
its larger diameter. Where rails are not installed, corner posts are braced to limit this
deflection. Popular bracing methods include:
• Short top rail for one panel to brace the corner post to the first intermediate post
• Diagonal brace from the upper half of the corner post to the bottom of the first
intermediate post.
• Diagonal brace from the upper half of the corner post to a concrete footing.
Strainer wires are a double strand of wire placed strategically at points where most stress
occurs. Where top and/or bottom rails are not installed, strainer wires are used to
support the top and bottom of the chain mesh.
Additional strainer wires are placed horizontally at hip and shoulder height to strengthen
the fence at the height where much of the impact from players occurs.
Strainer wires are installed as two strands and then strained by twisting. An alternative to
strainer wire is a “Helicoil” which is coiled wire that provides constant tension when
stretched out and installed to support chain mesh.
In all cases, the chain mesh is attached to the strainer wires using wire clips.
Strainer wire positions may alter from the above recommendations where sightscreens or
windscreens are to be installed. The strainer wires may become part of the support for
these screens.
8.3.6 Access
Access to the court is provided through pre formed welded gates. These gates are
placed inside arches. The chain mesh is tied off against the arches.
The court should include at least one double gate to permit access for machinery on to
the court. An example of this need is when lighting requires servicing and cherry pickers,
scaffolds and similar devices need to enter the court.
Gate hinges should be checked regularly. Where a gate hinge works loose, the gate can
drop and drag across the court surface when opening or closing. This can cause
damage to most surfaces, including synthetic grass, acrylic, etc.
8.3.7 Fence finishing

A range of fence finishes are available. These finishes may be for aesthetic purposes, to
protect against the weather, or both.
8.3.7.1 Galvanized vs. powder-coated fencing

Posts and rails are delivered galvanized. Galvanized posts may be powder-coated for
aesthetic purposes. The powder-coating assists by providing another level of protection
against the environment. During construction, care must be taken to avoid scratching this
coating.
Fence structures can also be painted. Painting has a limited life and powder-coating and
similar treatments are considered more cost effective.
8.3.7.2 Heavy galvanized fencing

Galvanizing is provided at different standards. The higher quality galvanizing deposits a
thicker coating of zinc on the base metal prolonging its life. These finishes should be
considered in situations close to the ocean or other corrosive effects.
Chain mesh is also galvanized and different grades of galvanized mesh are available.
Technical Manual 100

8.3.7.3 PVC coated mesh
Chain mesh may also be PVC coated. This coating is applied to the wire before it is
woven into chain mesh. The PVC coating enhances the appearance of the fence and the
additional level of protection extends the life of the fence.
Black or dark green chain mesh (and structures) blend into the environment much more
than a galvanized fence and significantly improve the appearance of a tennis court.
8.3.8 Mesh size (diamond and wire)

Chain mesh is manufactured in a machine that weaves the wire into diamonds. Chain
mesh is specified by:
• Size of the diamond (measured between the parallel faces). This is referred to as
“pitch”. The Australian Standard for tennis court fencing has adopted 45mm
diamond. In some states, 50mm diamond is used as 45mm mesh is not
manufactured as a standard size.
• Thickness of the wire used to manufacture the mesh. Court fencing uses either
2.5mm or 3.15mm thick wire. The heavier the wire the stronger the mesh and the
longer fence life that can be anticipated.
• Finish on the wire (PVC coated, heavy galvanized, etc.). PVC wire has the coating
applied over standard galvanized wire prior to weaving. “Heavy Galvanized” wire
has an additional coating of zinc to protect it from the elements.
Standard widths for chain mesh determine the popular fence heights of 3.6m and 3.0m.
Low height dividing fences often use the standard size of 1.2m.
8.3.9 Dividing fences.

Where courts are
aligned in banks of two
or more courts, dividing
fences are
recommended. This
prevents a ball from one
court rolling across an
adjoining court and
disrupting play.
Generally, dividing
fences are full height for
two panels and then
slope down to 1200mm
height in the centre.
An opening of one or
two panels of the
dividing fence is often
left near the net line of
banked courts.
If side lighting is
installed between
banked courts, a
dividing fence back to
the light pole is often
used to avoid players
running into the light
tower. This is
addressed more fully in
Section 8 elsewhere in
this manual.

8.3.10 Draw back curtains
An alternative to a rigid dividing fence is a draw back curtain.
The curtain is manufactured from
polypropylene mesh similar to that used for
the tennis net. The curtain is suspended
from a strainer wire at the top and is
weighted at the bottom.
The ability to draw the curtain back allows
the court to be opened up for coaching or
other activities.
Another advantage to the draw curtain is
that its softness lessens the chance of an
injury from a player running into the
dividing fence.
8.4 Timber fencing

Timber framed fencing is often erected for aesthetic
purposes, particularly in domestic situations for
courts in heritage houses. It has no other
advantages over metal pipe fences.
8.5 Attachments to fencing
8.5.1 Wind screens

Wind screens are often installed where a court is exposed to winds that can affect play.
Generally constructed of mesh material, the purpose of the wind screen is to divert the
wind up and over the court. The wind screen is attached to the fence, usually with the
bottom of the wind screen providing a gap of about 600mm from the court surface.
A major issue with wind screens is the stress
they place on the fence when squalls pass
through. To some extent, this can be limited
by attaching the wind screen to the fence
with springs and/or ties that will fail under
excess load. This may work when the wind
is approaching from the side of the fence
away from the wind screen. When
approaching from the same side, the wind
screen is pinned to the fence like a sail and
exerts substantial loads.
Where wind screens are installed,
consideration needs to be given to wind loading. Often, additional bracing will be
installed to strengthen the fence.
Other forms of screens exist. Some are woven through the fence and replicate foliage.
8.5.2 Sight screens

Sight screens are similar in manufacture and use to wind-screens. Often, the same
product serves the dual function. Issues of wind loading relating to wind screens apply
equally to sight screens, rebound nets and other fence attachments.
Sight screens are generally fabricated in darker colours to provide appropriate contrast
between the ball and the background. They are placed on the fence to cover from
600mm above surface to 2400mm above the surface.

8.6 Maintenance and repair of fencing
Routine maintenance should include a safety check of the fence mesh, periodic
tightening and lubrication of gate hinges, checking fence fittings for loose bolts, checking
tension of strainer wires, etc.
Ties should be checked to ensure sharp edges do not present as a scratch hazard.
Chain mesh should be checked to ensure it is not curling up to allow balls to leave the
court.

At time of writing, a draft Australian Standard is being prepared.

9 Lighting
9.1 Introduction
The sport has seen a growth in both the number of courts
that have been lit for night play and an increase in the
quality of that lighting. Both of these effects are due, in
part, to improving technology providing better, more cost
effective lighting solutions for the sport. The growth in
court lighting has also grown out of players’ searching for
more comfortable playing conditions in the Australian
climate and a growing awareness and concern for the
harmful effects of sun exposure.
Lighting systems have also come under increased scrutiny
due to a requirement that court lighting should not intrude
into the lifestyles of people away from the court. This
includes neighbours, vehicular traffic, etc.

Corner Lighting Lighting installations that consist of flood lights placed on light
towers located at the four corners of the courts, or four corners of a
two court battery. These are generally mounted at a height of 10m
to 18m.
Illuminance This is a measure of the light striking a surface, such as a court
surface. In technical terms it is measured by the quantity of light
measured in lux and is calculated by dividing the light striking the
surface (measured in lumens) divided by the area illuminated
(measured in m2.) 1 lux = 1 lumen / m2.
Initial Illumination This is the average brightness over the playing area measured
when the lighting system is commissioned (new). Many lighting
systems, including Metal Halide systems, lose illumination over
their service life. The lighting industry generally adopts illumination
after 100 hours use as a measure of initial illumination. As lamps
age and reflectors and lenses become discoloured/dirty, lighting
levels on the court will drop significantly from the initial illumination
levels.
Light Loss Factor The ratio of the illuminance provided by an installation in the
or Maintenance average condition of atmospheric dust build up and with a lamp of
Factor average age expected in service, to the initial illuminance provided
by the same installation. (Note Light Loss Factor is always less
than one).
Luminaire This is the housing that contains the lamp. The term includes the
lamp, the reflector and the lens. Functions of the luminaire include
safe dissipation of heat generated by the lamp, exclusion of
insects, dust, moisture and other particles that may discolour the
lens or reflector and reduce the light output. The luminaire will
sometimes house the control gear (ballast, choke).
Maintenance This is a level at which remedial action needs to be taken to restore
Illumination illumination to a level suitable for play. Actions may include all or
some of lamp replacement, lens cleaning, reflector cleaning, etc.

Metal Halide These lamps consist of a gas enclosed in a glass envelope that
emits light when subjected to a current flow. Metal Halide lighting
systems are the most popular for lighting tennis courts and other
sports fields for their true colour rendition (white light), efficiency
(~90 lumens / watt) and reasonable comparative cost and long
service life. A large range of Metal Halide sports court luminaries
are available on the market and many of these tightly control spill
lighting and have been designed specifically for tennis. Metal
Halide systems are recommended for all new installations. These
types of lamps require up to 15 minutes from start up to full lumen
output. When switched off, they may take another 15 minutes or
longer to “re strike”. This can be a disadvantage where power
supply is suspect and may make them unsuitable for coin-in-slot
power sources.
Obtrusive Light Spill light which, because of its quantity, direction, etc, taken in the
context of the environment, caused annoyance, discomfort or
distraction to persons away from the court. This light could cause
interference to lifestyles of neighbours, create glare that interferes
with traffic lights, etc.
Principal Playing The area of the court bounded by the playing lines (i.e. baselines
Area (PPA) and doubles sidelines) plus the area extending 3.048m beyond the
baselines and 1.829m beyond the doubles sidelines.
Side Lighting Lighting installations that consist of luminaries placed on light
towers located along the sides of the court or courts. These are
generally mounted at a height of between 6m and 9m.
Spill Light Light emitted by a lighting source which falls outside the
boundaries of the area intended to be lit. Most commonly, this is
light that falls onto neighbours’ properties.
Total Playing Area The total court area including the principal playing area and the
(TPA) court surrounds to the edge of the court surface.
Tungsten Halogen This lamp consists of a metal filament enclosed in a glass envelope
Lamps filled with gas. It is a development of the incandescent lamp and is
more efficient (22 lumens / watt) and delivers a brighter, whiter
light. The advantage of this lighting system for tennis courts is the
low cost per luminaire. This arises out of both the lower cost of the
luminaire and its smaller size allowing it to be fixed using low cost
light poles. Disadvantages over other systems include its relatively
higher running cost, shorter life span, lower illumination levels.
Tungsten Halogen lamp sources are suitable for residential
installations only.
Uniformity Ratio This is a measure of the uniformity of light on a tennis court. It is
important as it measures the difference between the bright areas
and the dark areas. As a ball travels from bright to dark to bright it
creates difficulty for the eye to follow it and predict the time at
which it will reach the racquet.
Uniformity is generally calculated as the ratio of the minimum

luminance measured on a court to the average measured over the
principal playing area. Note that this definition can vary between
different lighting publications.
9.3 Types of lighting systems

Lighting systems are defined by the type of lamp used in the luminaire and the placement
of the luminaire relevant to the playing area. For example, the lighting for a court may be
described as corner mounted Metal Halide, side mounted Metal Halide, side mounted
Tungsten Halogen, etc. There are further variations within these categories, each
offering advantages and disadvantages to players using the courts.
9.3.1 Lamp types.

Early court lighting was predominantly
incandescent lamps or, a little later on, fluorescent
lamps. Relatively cheap to install these provided
poor lighting for tennis and would not be
considered for new lighting installations. Most of
these systems have been phased out.
Modern tennis court lighting systems consist
predominantly of Metal Halide lamp luminaires or
in some cases Tungsten Halogen lamp luminaires in residential installations.
9.4 Pole configuration and heights

Luminaire placement is generally along the sides or in the corners. Side mounted
luminaires are typically at the net line and about the base line for six lamp systems or
about the service line for four luminaire systems.
A six light per court
configuration is
strongly
recommended for all
new tennis centres.
A range of sensible
locations for these
poles is shown on
the diagram at right.
The ideal spacing
for these poles is
approximately 10.5
metres from the
central poles at the
net line.
The light fittings
should also be
mounted on
brackets at the top
of these poles so
they effectively
overhang the court
and more effectively
illuminate the
Principal Playing
Area (PPA). These
brackets can be up
to 1.0m in length.
Local Council light
spillage regulations
can also have an
impact on luminaire
positioning. There-
fore, any light
spillage beyond the
property fence line
should be kept to a
minimum.

Corner systems are self-explanatory. Although
not ideal, sometimes four luminaires (or groups
of luminaires) can be used to light two courts.
Mounting height of the luminaires varies within
the different configurations to increase
uniformity and reduce glare.
The placement of the light poles - luminaires -
is determined by the luminaire design. Every
luminaire has a particular photometric
distribution or light “footprint” that determines
its exact placement relative to the playing area.
The lighting manufacturer will provide
information on the exact point of placement of
the luminaire and this, in turn, determines
where the light pole will be placed. Note that
the pole must be placed clear of the playing
area for safety reasons.
The general formula for mounting height of luminaries is given by H= (Dx0.44)+4 but
in any case not less than 8.0 metres whichever is greater.
H is Mounting Height above surface: D for side lighting is distance from the pole to the
centreline and for corner lighting distance from the pole to the centre of the lit area.
Higher poles may be required to limit spill lighting.
Pole footings and foundations should be designed by a Structural Engineer.
9.5 Choice of lighting systems

The critical elements when choosing a lighting system are colour temperature,
illuminance, and consistency of light over the principal playing area and glare. Of course,
capital cost of the lighting system may also influence the choice. Generally, a more
expensive lighting system should result in less maintenance and running costs initially.
9.5.1 Colour temperature

Colour temperature refers to the ‘whiteness’ of the light. Metal Halide and Tungsten
Halogen produce a white light. Other lamps, such as Mercury Vapour or High Pressure
Sodium are efficient lamps but unsuitable for tennis due to the colour of the light.
9.5.2 Illuminance
Illuminance can be improved by using brighter lamps or a greater number of lamps.
Increases in illuminance result in increased capital and running costs and a balance
needs to be sought. The Australian Standard provides illumination levels suitable for the
various levels of tennis played. This Standard should be used for clubs when specifying
lighting levels for club use.
The following table illustrates this level in comparison to other levels of play.
Maintained Horizontal Illuminance Values
Minimum Horizontal Illuminance
PPA TPA
Level Of Play
(Lux) (Lux)
Recreational & Residential 250 150
Club Competition 350 250
International and National 1000 800
All values are based on illuminance levels measured 1.0 metre above the court surface.

A computer generated lux plot should be provided using a PPA (Principal Playing Area)
illuminance grid of 65 points and TPA (Total Playing Area) illuminance grid of 115 points
that meets the above requirements. Horizontal Illuminance reference plane should be 1.0
metre above court surface.
A review of illuminance levels with a calibrated light meter should be undertaken on
completion of installation to ensure calculated illuminance levels have been achieved.
9.5.3 Uniformity
Consistency of light is measured as ‘uniformity’. This is also reported in the Australian
Standard and clubs should specify lighting to meet the appropriate Standard for their use.
The measure of uniformity describes mathematically how even the light will be on the
court. Where uniformity is poor, the eye struggles to follow the flight of the ball and
predict its speed and when it will reach the hitting zone.
Uniformity of Light Distribution

Minimum Horizontal Uniformities
Level Of Play
PPA TPA
U1 min U2 min U1 min U2 min
Recreational & Residential 0.6 0.3 0.2 0.1
Club Competition 0.75 0.5 0.3 0.2
International and National 0.75 0.5 0.5 0.3
Note: All uniformity values are based on illuminance levels

measured 1.0 metre above the court surface.
The above table provides two measures of uniformity:

U1 min This measure of uniformity is the ratio of the minimum illuminance level reading
obtained as a proportion of the average illuminance level reading.
U2 min This measure of uniformity is the ratio of the minimum illuminance level reading
obtained as a proportion of the maximum illuminance level reading.
Uniformity is improved by installing more luminaires and/or choosing luminaries with
reflectors and other components designed to provide even light. The placement of the
luminaires relevant to the principal playing area is important to maximize uniformity and
this placement is determined by the reflector design. Placement includes positioning
relative to the court as well as mounting height. A lighting plan designed for one
luminaire may not suit another luminaire.
9.5.4 Light Loss Factors

The table on the following page details the typical lumen depreciation of the metal halide
floodlight for a number of differing environmental / atmospheric conditions (e.g. airborne
dust). It is worth noting the light loss factor is greater if the interval between regular
cleaning of the light fittings is extended. Therefore, consideration needs to be given to
the anticipated frequency of such maintenance when designing the lighting system to
ensure the expected lighting levels at the end of the planned maintenance period remains
greater than the desired minimum lighting levels.

Typical Metal Halide Floodlight Light Loss Factors
(inclusive of lamp depreciation & environmental pollution)
Cleaning Industrial Areas Residential Areas Rural Areas
Interval
12.0 months 0.81 0.83 0.85
24.0 months 0.74 0.76 0.80
36.0 months 0.63 0.68 0.73

Note 1: Lamp depreciation data is based on typical metal
halide lamp curves.
Note 2: Lamp depreciation is based on average usage of 24
hours per week.
Floodlight wiring should be oversized from the manufacturer’s recommendations to take

account of voltage drop. Voltage drop increases as the length of cabling increases,
which in turn affects light output of lamps. This is a common oversight when installing
lighting system and is usually a contributing reason as to why lighting levels are unable to
be sustained to the desired levels over time.
Voltage drop causing reduced lighting levels and premature bulb failure can also be
experienced when electricity suppliers reduce the electrical supply through their networks
(e.g. from say 240 Volts back to around 220 Volts). Whilst suppliers will not admit to this
practice, it does occur from time to time and can cause considerable anguish to tennis
centres. If this problem is suspected, the local electrical supplier should be requested to
verify the voltage being supplied to the site. However, this verification should only be
sought after ascertaining if there is not a voltage drop issue resulting from undersized
cabling or excessive cable length.
9.5.5 Glare
Glare occurs when the placement of the lamp is in the line of sight of the ball. Glare is
reduced through lamp and reflector design, positioning of the light towers, height of light
towers, etc. Luminaire manufacturers develop designs to suit their particular luminaires
when they are used for tennis court lighting.
Maximum on court glare rating GRmax= 50
9.5.6 Circuit switching

Switching needs consideration, particularly when Metal Halide lamps are used. If turned
off, these cannot be re-ignited until they have cooled. This may take fifteen minutes or
more.
Another switching issue is the ability to turn court
lighting on, one court at a time. This can save energy
costs when court usage is low.
9.6 Council regulations

Spill lighting is a growing issue for councils as
neighbours, road users and others not using night
tennis courts demand that spill lighting not intrude on
their lives.
Councils have responded to these demands by developing standards that govern lighting
design. These standards have maximum lighting limits that must not be exceeded at the
property boundary. Where courts are close to property boundaries, or neighbours are
located down hill from the tennis court, the standard may be more difficult or even
impossible to achieve and still provide quality light to the tennis court.
As regulations vary from council to council, this issue cannot be adequately addressed in
this manual. Tennis Queensland recommends that clubs and associations contact their
local council and obtain copies of regulations in force. These can be provided to the
lighting designers who will include those requirements when computer modelling an
acceptable design.
9.7 Maintenance of lighting

As with other aspects of tennis court operation, thought must be given to maintenance of
the lighting installation. A number of aspects of this should form part of the club’s
management plan. The management plan should include costing of these elements so
that funds can be reserved for this purpose.
9.7.1 Lamp maintenance

Lamp life varies according to the type of lamp used. For example, a Metal Halide lamp
may provide up to ten times the life of a Tungsten Halogen lamp. However, Metal Halide
lamp output degrades over time. A lamp replacement schedule will need to take account
of the lamp life, court usage, type of luminaire, etc. Generally, group replacement of all
lamps simultaneously will deliver savings in access costs (cost of cranes, cherry pickers,
etc).
9.7.2 Luminaires
Luminaires require periodic servicing. Lenses become dirty, as do reflectors. Lamp
usage causes the air inside the luminaire to heat and cool. The expansion and
contraction of the air draws in airborne contaminants, pollutants, insects and the like as
the seals age. Contaminants are also deposited on the outside of the lens and baked on
by the heat of the lamp. Court owners should seek advice from luminaire manufacturers
on cleaning regimes and appropriate chemicals to use. The club should not forget
access needs when servicing luminaires. Generally this maintenance will require an
experienced electrician with a ‘cherry picker’ or other approved access method.
Luminaire housings and electrical control
gear should also be maintained. Cabling
will require periodic checking by a qualified
electrician, as will electrical distribution
boxes, switchgear, timers, etc.
9.7.3 Light towers

Light towers should also be inspected
periodically. Footing bolts, welds,
attachments, etc may each deteriorate
over time and a visual inspection during
routine maintenance is recommended.
AS 2560 Guide to Sports Lighting

AS 2560.1 Part 1 General Principles;
AS 2560.2.1 Part 2.1: Specific Application - Lighting for Outdoor Tennis;
AS 3000 Australian Wiring Rules;
AS 3665 Simplified Definition of Lighting Terms and Quantities;
AS 4282 Control of the Obtrusive Effects of Outdoor Lighting;
AS/NZ 60598.1 Luminaires – General Requirements;
AS/NZ 60598.2.5 Luminaires – Particular Requirements – Floodlights

Tennis Australia Technical Instruction - Lighting for Outdoor Tennis
9.9 Typical Suppliers

• Hamilton - LSI Lighting Systems phone number (07) 3368 0200
• Moon Lighting phone number (07) 3621 9275
• Sylvannia Lighting phone number (07) 3034 8600
• Spectra Lighting phone number (07) 3335 3500

10 Accessories and amenities
The type and use of accessories will very according to
a] Type of facility
b] Choice of surface
There is a wide range of desirable and useful products that every court owner should
consider to assist in keeping the facility clean and attractive. A facility that is well
presented at all times will attract players and make their experience a pleasant one.
10.1 Net posts

Regardless of type of surface, all tennis courts need quality
net posts that are installed correctly. Very few ‘furniture
items” are placed on the court to dress it up and the quality
and appearance of the net posts and net make a significant
difference to the attractiveness of the court.
According to ‘The Rules of Tennis’, net posts should be no
more than 152mm in diameter, or 152mm square, and not
higher than 25mm above the net cable. Circular posts
should not be less than 73mm in diameter, and square posts
should not be less than 76mm square.
Most net posts are made of steel, with internal brass winding
mechanisms. Some manufacturers also supply wooden
posts, similar to the posts used at Wimbledon.
Apart from the wooden posts, the majority of posts come in powder coated black or green
colours. Posts are equipped with internal brass winding mechanisms, with a small handle
that can be removed or reversed so that they fold flat against the post.
Older type winders that jut out from the post are a safety
hazard, and are not recommended. This is particularly the
case when children’s coaching classes are conducted. The
older winders protrude from the post at the head level of
young children, and pose a danger when they run from one
end of the court to the other.
Net posts may be permanently installed, or they can be set in
sleeves [usually supplied by the manufacturer] to allow
removal. Setting them in sleeves is preferable, so that future
replacement does not require the footings to be dug out. The
top of the sleeve should be installed some 6 to 8 mm above
the finished court surface, so that rainwater does not run
into the sleeve. The sleeve should be installed in the centre
of the footing, and care should be taken to ensure the sleeves are truly vertical. Some
contractors will set sleeves slightly off vertical so the net tension pulls the post in the
sleeve to a more vertical position.
Net post footing design will vary according to local soil conditions. In any event, it should
not be less than 450mm diameter at the top, 650mm deep, and 600mm square at the
bottom. Footings placed in sandy soils will need to be increased in size to avoid moving
off vertical after a few years.
Round post footings are recommended for asphalt and concrete courts to prevent radial
cracking, especially when footings are poured after the asphalt or concrete has been laid.
Square corners on the top of footings can cause stress points from which cracks can
begin. If footings are poured prior to laying an asphalt layer, care must be taken to
prevent the sleeve being damaged or asphalt spilling into the sleeve. For concrete courts
the footing can either be poured integrally with the slab, or else isolated by an expansion
joint. A footing block-out can be used with the concrete slab pour.

Be aware that regardless of the diameter of the post, the sleeves should be set 12.80
metres apart, centre to centre of sleeve. For tournaments using stadium courts it is
recommended that a second set of sleeves be installed 10.06 metres apart for singles
play. Singles sticks may be used on all other occasions, and for match courts outside the
stadium. Singles sticks should be 1.067 metres high at the bottom of the V so that the
net cable is positioned at the correct height.
Singles sticks may also have a line cut in them at a height of 914 mm so that they can be
used to measure the correct height of the net at its central point. Marks may be painted
on hard courts to indicate singles sticks positions.
10.2 Nets
Most tennis nets are made of braided polyethylene, which provides good resistance to
ultraviolet radiation and other forms of weathering. The braided material also absorbs
some impact, so balls hitting the net have some of their energy dissipated.
The traditional tennis net has a white headband made of UV stabilised vinyl or canvas.
Vinyl headbands are smooth, shiny and dust resistant. However the ball can skid off
them, and most players prefer canvas. Quality headbands contain two layers of fabric
and four rows of stitching to form the cable sleeve. Modern nets use propylene material
similar to that used for motor vehicle seat belts.
The net cable itself is generally PVC coated, and can vary from 4 mm to 6 mm thick. It is
not recommended that the net cable be tensioned too much, as this places stress on the
net post installation and its winding mechanism.
When installing the net, the PVC coating should be removed from the cable so it does not
jam the mechanism.
Nets can vary from 600mm drop to a tapered full drop. The full drop net is mostly used
for major tournaments, and is not recommended for regular club use. If the tennis net is
left out day and night, it is better to order a 760mm (“three quarter”) drop, and keep it
suspended above the court surface. Three quarter drop nets are also preferred for club
and social play as it permits balls to be rolled under the net when returning balls for
serve.
Side and bottom bindings are generally fabricated from
heavy duty PVC. Side bindings can have grommets
installed in them to enable the net to be laced to the
post. Additionally, better quality nets have a sleeve in
the side binding to accommodate dowels, which hold
the net taut, and present a neat appearance.
Heavy-duty nets may also have double mesh for the
first five or six rows directly beneath, and incorporated
in the headband. This is the area of most wear and
tear and the double mesh resists the stress, extending
the life of the net.
As a guide in choosing a net for a quality residential or tennis facility, the following
features should be sought:
a] Double thickness headbands, preferably made of canvas.
b] Multiple rows of lock stitching.
c] Braided polyethylene mesh, with double stitching for the top 5-6 rows.
d] 760mm drop.
e] 6mm PVC coated steel cable.
f] Dowels and grommets in side bindings.

10.3 Centre straps and anchors
Centre straps are used to ensure that the net is
positioned exactly 914mm above the playing
surface in the centre of the court. It also ensures
that the net remains in position when conditions
are windy, and helps keep the net in the required
position at all times. Straps are usually made of
polyester or nylon, 50mm wide, with a height
adjustable swivel hook at the bottom, to attach the
ground anchor.
The ground anchor should be set flush with the court surface, and parallel with the net
line. The concrete footing should be a minimum of 300m in diameter at the surface, and
375mm in diameter at the base. It should have a minimum depth of 300mm.
Note: The above diagram has not been drawn to scale.
10.4 Umpires chairs

The umpire’s chair is an important accessory for any tennis court. Clubs that have
regular competition must have a chair for each court, and even a home court used for
social play only, will benefit from having an umpires chair at court side.
Chairs should ideally have a non-marking flat wooden base for the leg supports so that
the court surface is not damaged. It is preferable to also have a canopy for sun
protection, with a flat arm section that can be used as a support for writing score-cards.
10.5 Court numbers

For club courts it is necessary to clearly define each court by number. In running
competition a lot of time can be saved if players can quickly ascertain which court they
are assigned to.
10.6 Ball machine
There is now a wide range of ball machines, and they are particularly useful for coaching,
as well as for the private court owner who may often have trouble arranging for a practice
partner.
Most ball machines today have a wide range of features that can provide oscillation,
varying speeds of trajectory, and varying spins on the ball. If you plan on using a ball
machine, a power source will need to be installed close to the court.
When choosing a ball machine it is important to trial its operation to ensure it meets all
the needs. One issue with ball machines is the noise emitted. Some are quite noisy and
may be unsuitable for tight residential situations.
10.7 Ball retrievers

There are several types available, and they are essential for coaching classes, so that the
balls are quickly gathered and returned to the coaching basket. Generally they are either
the wire coaching-basket itself, or they can be constructed of metal or plastic tubes, with
small protrusions inside the pick-up end to keep the ball in the tube.
Several tubes on a coaching-class court will keep the action moving, plus provide a
source of entertainment for children when it is not their turn to hit the ball.
10.8 Coaching baskets

Essential for all forms of coaching. They are basically a wire basket with legs that can be
reversed, and a moving section of the bottom for ball retrieval.
10.9 Hit walls and rebound nets

If installing a hit wall at a tennis facility, it is
advisable to make it a separate item, and not be
part of a tennis court fence where it can be both
a visible distraction and potentially damaging to
either equipment or players. To work properly it
should be at least 3.6 metres high, 10 metres
wide, and of concrete block construction on a
well designed and constructed concrete footing.
Engineering advice prior to construction is
recommended. Fencing should be placed above
and on the sides of the hit-wall area to contain
balls.
Rebound nets can provide a quieter and less obtrusive alternative. Additionally, they are
portable, and more suitable for use on an existing court.
10.10 Other court accessories

There are various other items that are useful, and in some cases essential, such as:
• Drag mats
• Squeegees
• Roll Sweeps
• Aussie Clean Sweep
• Court Brooms
• Line Brooms or Line Flickers
• Shoe Cleaners
• Court Signs
• Rollers
• Leaf Sweepers (see photo at right)
• Score boards
• Court Benches
10.11 Off court accessories
Amongst items that should be considered are:

• Shade Shelters for spectators
• Rubbish Bins
• Drinking Fountains
• Seating for spectators
• Power outlets
• Hose connections
• Storage areas for court equipment
10.12 Security and safety

A facility should have security lighting and a fencing design that limits access to the
amenity.
An intercom or loudspeaker system will assist tournament play and lines of
communication.
Other desirable features are nearby restrooms, changing facilities, and first-aid supplies,
all of which can be incorporated in the clubhouse design.
10.13 Suppliers of tennis court accessories

As with tennis court contractors, Tennis Queensland prefers not to recommend suppliers
of tennis court accessories and equipment. Again, we prefer to recommend suppliers of
such products that are members of the Sports Contractors Association. A complete list of
these suppliers can be obtained by contacting this group or by searching their web site,
(which is www.sportscontractors.com.au). From this list, some of the most “helpful” of
these suppliers have been listed here for easy reference.
Grand Slam Sports Equipment

19 Deakin St
Brendale Q 4500
Jordin Sports
4/84 Newmarket Road
Windsor Q 4030
Play Hard Sports Equipment

24 Ern Harley Drive
West Burleigh Q 4220
Sportzing Court Care Services

Level 1 Unit 18, 1645 Ipswich Road
Rocklea Q 4106
Multisport Concepts Pty Ltd
PO Box 2044
Burleigh DC Q 4220
Advantage Sports & Leisure

PO Box 573
Cairns Q 4870
Allsports Products Pty Ltd

PO Box 158B
Bungalow Q 4870
Sports Technology International Pty Ltd

PO Box 4260
Dandenong South VIC 3175
En Tout Cas
66 Keys Rd
Moorabbin VIC 3189
Raw Courts
mail@rawcourts.com or phone 0411 242 272

No standards exist for tennis facilities

11 Indoor tennis, enclosures and roof structures
11.1 Introduction
Roofing structures are of increasing interest to
tennis court operators as they seek to maximize
the use of their facilities through extremes of
climatic conditions ranging from excessive heat to
rain. Players are demanding greater comfort when
they play their sport and predictability, irrespective
of the weather conditions. These issues need to
be addressed to ensure the success of our sport
against competition from other indoor sports.
Roof structures include metal roofs, waterproof sail
type structures and shade structures. Roof supports may be in the form of a barn or a
suspended membrane. Roof structures are expensive to construct and some may
require ongoing or routine maintenance, creating a need for budgeting to accommodate
this in future needs.
Roof structures may be constructed over most court surfaces with only natural grass
presenting problems due to the need for sunlight to encourage growth. Several major
sports arenas have roll back roof structures but this level of technology is not addressed
in this paper.
Engineering design of roof structures is understandably important and no construction
should be considered without engaging an appropriately qualified engineer to complete
the design.
The height of the roof structure above the court surface is important to permit (relatively)
unobstructed play. Lighting requirements should also be considered when designing the
roof profile. In particular, stretched membrane roof structures may require air clearance
above lights to allow cooling air-flow to prevent damage to either the lights or the roof.
11.2 Court enclosures.

The dimensions of a full size tennis court as defined in the ITF rules are described in
section 4.5.1 of this manual. When enclosing a tennis court the dimensions must exclude
all structural members required for the court enclosure. For example, posts supporting
the roof structure must be outside the court dimensions providing a free area 36.6m x
18.3m.
11.3 Requirements of the rules

The International Tennis Federation rules do not include a specification for a roof over a
tennis court. The rules do, however, contain a recommendation.
The issue has been addressed by the United States Tennis Federation (USTA) and the
Lawn Tennis Association of Great Britain (LTA (Britain)).
11.3.1 ITF Recommendation on ceiling heights

The ITF Rules include a plan for the court specifying dimensions of the playing area and
suggestions on how to mark out a court. This section includes a “Note” on ceiling heights
that states:
As a guide, the recommended minimum height to the ceiling should be 30 feet
(9.14 m)
11.3.2 Construction Manual – USTA

A manual is published jointly by the United States Tennis Court & Track Builders’
Association (USTC&TBA) and the USTA. In the section on Indoor Tennis, this manual
describes roof clearance requirements as follows:

“The space directly over the court should be free of overhead obstructions and
there should be not less than 18ft. (5.487m.) at the eaves, 21ft. (6.401m.) over the
baseline and 35ft. (10.668m.) at the net, although 38ft. (11.582m.) is
recommended, measured to the interior finished ceiling”
11.3.3 Guidance Notes – LTA (Britain)

The LTA (Britain) publishes Guidance Notes for use by their clubs and associations. In
the section “Tennis Hall Dimensions” the following information is provided on roof heights.
Unobstructed height at the net line 26ft. 6ins. (9m)
Unobstructed height at the base line 18ft. 11ins. (5.75m)
Unobstructed height at rear of the run back 13ft. 1in. (4.00m)
11.4 Types of roof structures
11.4.1 Rigid structures

Rigid structures range from stadiums such as the Rod Laver Arena at the National Tennis
Centre in Melbourne to multi use sports halls and ‘shed’ structures.
Sports halls, stadiums and similarly engineered structures are beyond the scope of this
manual.
There is growing interest among clubs to construct shed style structures over tennis
courts to provide relief from sun and rain. A number of construction companies provide
roofing for sporting venues such as lawn bowls that adapt readily to tennis. An example
of a company that offers a shed structure is Big Country Buildings in Queensland.
11.4.2 Membrane structures

Membrane structures consist of metal posts or
frames with a fabric membrane stretched
tightly above the court.
A number of tennis courts in Australia are
protected by these structures. Examples exist
in Western Australia and on the Gold Coast in
Queensland.
A number of companies are providing these
structures, the best known of these servicing
Queensland include:
• Taiyo Membrane Corporation (formerly Shade-Bird-Air)
• Universal Fabric Structures
• VESL Tension Span Structures
• Vanguard
11.4.3 Inflatable structures

Inflatable structures are membrane fabric structures that are supported by positive air
pressure rather than rigid structural members.
This type of structure is more appropriate for temporary installations. In addition to the
capital cost, these structures consume energy to maintain shape. Savings in capital cost
may be consumed within the life of the structure.
There are currently no inflatable structures in use for tennis in Australia although they are
used internationally.

11.5.1 Rules and guidelines

http://www.itftennis.com/technical/rules/
http://sportsbuilders.org/page.php?id=13&from%5B%5D=11&from%5B%5D=12&
11.5.2 Suppliers on the Internet.
Rigid steel buildings / structures:

www.bigcountry.com.au
www.asibuild.com.au
Tensioned membrane structures:

www.taiyo.com
www.vesl-tensionspan.com
www.fabricstructures.com.au

12 Club facilities
12.1 Introduction
The size, location, and layout for a clubhouse will vary from site to site, depending on a
number of factors:
• Number of courts planned for the tennis facility
• Land topography
• Type of facility and whether there is a shared use with another sport
• Other specific needs of the club membership
12.1.1 Layout
There are some fundamental requirements however. The clubhouse preferably should be
centrally located to the courts, and close to the parking area. The manager's office and
reception areas should adjoin, and both of these areas have a clear view of as many
courts as possible.
The positioning of a pro-shop should be adjoining the reception area, so that anyone
entering or leaving the shop passes by the reception area. Some additional video
security may also be necessary to adequately supervise these areas. Adequate storage
areas for supplies to the reception area and pro-shop should also be positioned in an
adjacent location so that these areas can be quickly serviced. The manager's or
professional's office should have sufficient room for files, and a small meeting area.
A kitchen, cafe, and players' lounge, opening out onto a large covered deck, with views
over the courts is also most desirable. The kitchen and cafe should be equipped to
supply a variety of food similar to a coffee shop. During tournaments this area will
receive a constant and heavy amount of use, and provision should be made to spill out
onto a covered deck and/or adjoining shaded areas that overlook the courts.
A tournament office should be located so that as many courts as possible are in view.
Provision should be made for a large notice board on an external wall of the tournament
office where draw-sheets can be pinned, so that players and spectators can examine the
sheets without entering the tournament box itself. Sufficient showers and toilets and
perhaps lockers should be incorporated, to cater for the size and type of facility.
Tennis Queensland’s Technical Services Department have a library of club house
designs of various sizes and configurations. Please feel free to contact them any time to
see if they have a design that might suit your needs. Otherwise, they can produce an
indicative design that will suit the layout of your facility and ensure the key relationships
between the car parking areas and the positioning of the courts is reflected in the design,
thereby maximise the effectiveness and usability of your club house.
12.1.2 Size requirements

As a general guide, a clubhouse to adequately provide sufficient amenities for a 10-12
court centre should have a total area of 450 sq metres. It would include the following
spaces as a minimum:
Lounge, club rooms, cafe area 170 sq m.
Kitchen area 30 sq m.
Pro-shop 50 sq m.
Manager's Office 16 sq m.
Bathrooms 50 sq m.
Store Rooms 36 sq m.
Deck 90 sq m.
Tournament Box 20 sq m.

12.1.3 Other provisions
Provision should be made for disabled access to all areas, and a disabled toilet installed
within the toilet block. Wheelchair tennis is becoming more popular, and thought should
be given to making court access available, so that a wheelchair tennis event could be
conducted.
Public telephones and sources of drinking water should be available. A public address
system is essential to the running of tournaments.
As with all building projects, the final design will need to be completed by registered
professional designers recognised by the local government authority having building and
planning jurisdiction over the site. Development and Building Approvals will be required
from the relevant local government authority before any construction works can
commence on site, along with the required inspections and approvals obtained during
construction to allow lawful occupation of the building on completion.

13 Managing a project
13.1 Introduction
Project Management of a complete tennis complex is a specialised role that generally
requires the engagement of a professional manager with at least a substantial
understanding of all the topics covered in this manual. Alternatively, a person with non-
tennis based Project Management skills (i.e. a person with a professional background in
the construction industry, such as an engineer) could be capable of undertaking this role
provided they have access to other people with this tennis specific knowledge who can
assist and/or review project progress at key points of the project.
Similarly, smaller projects, such as repairs and resurfacing, or maybe even the
construction of a single court could be undertaken by owners or club members providing
they have also obtained the right technical guidance from the outset and along the way.

Bill of Quantities or a A list of all the items of work required in a project provided to all
Schedule of Rates contractors pricing this project to make comparison of all quotes
received an easier process
Defects Liability A nominated timeframe included in a building works contract
Period during which the contractor is obliged to return to site to rectify
any defective works identified after Practical Completion has
been achieved
Geotechnical An professional engineer who specialises in analysing soil
Engineer conditions and subsequently determining what sort of base
construction is required for a tennis court (or foundations for a
house or other structure)
“hold points” Nominated time/s at which no further works can proceed until all
parties agree the works completed up to that stage of the works
are in accordance with the specified requirements
Practical Completion The date when all parties agree the specified project works are
completed to the point where they are fit for its intended use
Progress Payments Payments made by the owner to the contractor either on
achievement of set project milestones or on a regular timeframe
basis (i.e. fortnightly or monthly)
Retention Monies withheld from progress payments from the owner to the
contractor as security that the contractor will complete the works
and rectify any defects after Practical Completion has been
achieved during the Defects Liability Period
Technical A document produced by the owner or the owner’s Project
Specification Manager or other consultants detailing the scope of works
required and the minimum standards or requirements by which
this work is to be completed.
Topographical A site map produced by a Surveyor showing the existing site
Survey levels, approximate contour levels and existing features to
provide the contractor with an indication of the site works
required prior to construction of the tennis court base
13.3 Obtaining technical guidance

There are very few professional design groups who have this specialised expertise with
regards to all aspects of a typical tennis court related project. Therefore, the best source

of such information will generally be your local affiliated body in your state or territory (i.e.
Tennis Queensland).
These bodies generally have a department which specialises in providing this expert
advice as they have access to unique individuals who have been building or overseeing
the construction of such facilities for 20 years or more. They may also include other vitally
important professionals with a wealth of experience in specific aspects of tennis courts,
such as Geotechnical Engineers, Electrical Engineers, Civil / Structural Engineers and
court surfacing specialists.
13.4 Site investigation

It is essential that the first consultant approached when contemplating the design and
construction of a tennis court is a Geotechnical Engineer. This specialist consultant will
undertake site investigations by means of drilling bore holes and taking soil samples
around the proposed site to ascertain the existing soil conditions. The results of these
samples and tests are then used to determine the structural requirements of the tennis
court base to be constructed, depending upon the proposed playing surface.
Before any other design works can proceed, a Surveyor should be engaged to produce a
topographical survey of the site. A topographical survey shows the existing levels over
the site to determine the following:
• existing path of overland water flow so that this can be considered and
incorporated into the design,
• the extent of earthworks that will be required to create a platform upon which the
tennis court base can be constructed, and
• identify the exact location of any existing features on the site – such as trees,
fences, buildings, concrete pathways, power supply lines, water meters, etc. to
ascertain if any of these will have an impact on the proposed construction works
(i.e. whether any of these sorts of structures may need to be demolished or
relocated)
13.5 Preparing a technical specification

Technical specifications for tennis court construction are again best left to those select
few who possess an intimate knowledge of all aspects of tennis court construction, or for
a Project Manager to assemble based on advice sourced from specialists in their field of
expertise (e.g. an Electrical Engineer providing advice on flood lighting systems).
Again, the best source of such advice on preparing technical specifications will generally
be your local affiliated body in your state or territory (i.e. Tennis Queensland).
A well prepared technical specification that clearly details the required scope of works will
minimise the chances of there being any disputes during or at completion of construction
as to what the intended scope of works was. This is by far the most common cause of
disputes between owners and contractors (others generally relate to workmanship or
payment issues).
It is highly recommended that the technical specification document is accompanied by a
detailed Bill of Quantities or a Schedule of Rates. This document should itemise all the
works required so that all contractors pricing this project are doing so on the same basis,
thereby providing a basis upon which to compare the quotes received.
13.6 Inviting tenders from the construction industry

Unfortunately, as with every other sector of the construction industry, there are a number
of “shonky” contractors in the marketplace. There are a number of glorified concreting or
landscaping firms passing themselves off as tennis court constructers with little
understanding of the technical aspects of tennis court construction. Often the result of
engaging these contractors is a tennis court or courts with inadequate base preparation
leading to major structural failures and ongoing costly maintenance issues that become
evident after only a relatively short period of time.

So why do some people and clubs seem to continue finding themselves in this situation?
Generally it is a question of money. These contractors will invariably offer to construct
their courts at significantly lower prices than their more recognised and higher quality
competitors. Given that many clubs struggle to raise funds to undertake such works, the
temptation to minimise their outlay on such relatively large projects (for them) is often all
too appealing. The old adage that “you only get what you pay for” is so very true when it
comes to tennis court construction.
It is suggested that if you are looking for firms to tender or quote upon your new tennis
court or complex, that time is taken to research the credentials and references of these
firms. Arrangements should be made to inspect some of the contractor’s previous
projects to get a feel for their quality and level of workmanship. The financial outlay for a
tennis court is substantial, so the time should be taken to conduct this research before
you hand over your hard earned money.
It is also recommended that contact be made with your state or territory division of the
Sporting Contractors Association (ph. 1800 208 202 or www.sportscontractors.com.au) to
obtain a list of tennis court contractors that are members of this group. Whilst
membership of this association is still no guarantee that you will receive the quality court
that you deserve, the risk of selecting a rogue contractor is greatly reduced. Members of
this group are required to regularly demonstrate the quality of their workmanship to retain
their membership status, and their peers are generally quick to ensure their collective
reputations are not being tarnished by any individual in their ranks.
The same background checks recommended above should be carried out even if
requesting a tender from members of these associations to ensure you are dealing with
individuals or firms that you feel most comfortable in dealing with.
When requesting contractors to provide you with a quotation, it is recommended that you
give them at least 2-3 weeks to review the project specifications and any other
information you may be able to provide them with. This allows them sufficient time to
review and comprehend all the documentation provided as well as obtain any prices they
may need from their suppliers.
Consideration should be given to the reality that they may well be in the process of
constructing another project somewhere else during business hours whilst preparing your
quotation out of hours. Therefore, giving them this reasonable timeframe in which to
prepare your quotation or tender allows them some flexibility in which to find the
necessary time to devote to this exercise. Chances are that they may be quoting on more
than one project at any time.
If you don’t give them sufficient time in which to prepare their tender, they will probably
not absorb the information provided or they will err on the side of caution when preparing
their quotation. As a result, your quote may not be as competitive as perhaps it could be
and you may end up paying more for your tennis court/s than you could have – all for the
sake of a week or two at this critical stage of your project.
If you have a project with a tight and finite budget, it may be prudent to prepare a Bill of
Quantities or Schedule of Rates which covers the basic or minimum construction
requirements that will safely fall within the budget. From this point, further items can be
added to this base price on an option extra basis (like adding extras such as air
conditioning or sporty wheels to a base model new car). This will provide you with the
ability to choose the options that you can afford to add to your basic tennis court
construction up to the limits of your budget.
Whether you are on a tight budget or not, a contingency allowance should always be set
aside from the quotation price accepted. This will provide a buffer for the unexpected or
accidentally forgotten items that always seem to crop up during any construction project.
A safe allowance is normally around 5% of the accepted contract price, however lesser
amounts can be safely used where there is minimal “in-ground” works required or the
specification documents produced are considered to be of a high standard of quality.

13.7 Choosing between tenders
This process can be made considerably easier if all quotes are based on a clear and well
detailed project specification and, as mentioned previously, a well compiled Bill of
Quantities or a Schedule of Rates. If this is the case, the choice, if being based purely on
cost, can be made much easier.
However, as discussed previously, consideration should also be given to the contractor’s
performance on recent projects (based on their references), the demonstrated quality of
their workmanship (as evidenced from inspections of previously completed projects) and
your own impressions from communications up to this point (and references obtained) as
to whether you feel comfortable dealing with each of these contractors.
Depending upon the emphasis placed on each of these criteria, the choice may be simple
or very difficult. On larger projects, it is not uncommon for each of these criteria to be
given a weighting (say 50% for price, 20% for previous performance / references, 20% for
demonstrated workmanship and 10% for being able to work well with this contractor). The
weightings for each of these items (and others that may be applicable to your project) can
be modified to reflect the nature of the project and your own priorities.
Each tender submission is then marked against each of these weighted criteria so as to
arrive at the “best” value for money offer. Having undertaken this exercise, it is possible
that you may still be faced with a tough decision between two or more contractors. If this
is the case, you may need to focus on the scores given to each of these contractors
against the most heavily weighted selection criteria as a guide, as these are obviously
your areas of main concern. Alternatively, you could interview each of these contractors
again and discuss your key areas of concern with regards to their submission to either
confirm or allay your fears in this regard. It may also provide some vital feedback to these
tenderers as to where they may need to improve in order to secure future business for
themselves.
There is nothing to say this same exercise cannot be undertaken on any size project –
not just large projects. An individual tennis court for a home owner may be a relatively
more stressful (financially and otherwise) undertaking than a complete complex may be
for a wealthy developer. It may actually be beneficial to advise prospective tenderers that
their submission is to be evaluated on criteria other than price alone, as they may take
more time to address the way in which they approach you before, during and after this
tendering process.
If you have engaged a project manager to oversee all stages of your project, they will
devise their own methods of reviewing and recommending a tender submission to be
accepted, generally along the lines of the process outlined above. Remember, the Project
Manager will only make a recommendation as to who they think you should enter into a
contract with to undertake your project, and it may well be beneficial to do your own
review to see if you concur with their recommendation/s.
At the end of they day it is your decision, and it is one that you will have to feel
comfortable with for a long time once it has been made. So take your time and choose
wisely!
13.8 Contracts and project acceptance

Once a decision has been made to accept a contractor’s quotation or tender, the next
step is to advise them of your intention to accept their offer and advise any other
contractor’s that their bids have been unsuccessful. This allows both the successful and
unsuccessful tenderers to either begin planning and preparations to undertake your
project or to move on and price another project without worrying about whether they
might put themselves in a position where they end up with more work than they can
physically handle at any one time.
Unless the quotation you are planning to accept has specifically nominated that it is
conditional upon entering into a particular form of contract, the next step is to come to an
agreement with that contractor on a set of contract conditions that you can both work
with. If they have nominated a specific form of contract in their quotation, this needs to be

taken into consideration when comparing this tender with others received. If there is a
specific form of contract that you wish to use, this could be nominated in the project
specification provided to contractors during the tender period.
There are three Australian Standard forms of contract available, AS 2124, AS 4000 and
AS 4305, although these contracts are written predominantly with building contracts in
mind. Other less commonly used Building Contracts include JCC, NPWC, QMBA and
QBSA contracts. The Sports Contractors are currently considering the development of a
standard form of contract that specifically relates to the construction of tennis courts and
other sporting facilities, but this may still be some years away from being finalised.
13.9 Project supervision

Unless you have absolute faith in the abilities of your contractor and trust them implicitly,
or the owner has a good degree of knowledge about tennis court construction, it is
recommended that owners engage someone with this ability to supervise the contractor’s
work at various key points during construction. These intended key points or “hold points”
should be identified in the project specification so that the contractor is aware they cannot
proceed with any further works on the project until their works up to that point have been
inspected and it is agreed these works have been completed to a satisfactory standard.
Again, these standards should also be clearly described in the project specification.
An example of a typical tennis court project hold point would be the provision of soil
compaction test results to demonstrate that the sub-base prepared meets the specified
requirements and is therefore is suitable for subsequent base construction works to
commence. Another example would be an inspection of the under slab plastic membrane,
tied reinforcement mesh and edge formwork for compliance with the project specification
prior to pouring and finishing of the concrete slab.
If for any reason, the works up to this stage are not of an acceptable standard, the
contractor should be instructed to rectify this situation in accordance with the project
specification requirements. The best placed person to make these inspections will be the
person who wrote the specification documents relating to that aspect of the works, or an
extremely competent project manager with a professional background relevant to the
works they are inspecting. For example, the completed earthworks and associated test
results should be reviewed and approved (or otherwise) by the Civil or Geotechnical
Engineer who prepared the plans and specification for this aspect of the works (if
required).
These checks should ensure that any potential cause of defects as a result of poor
workmanship or building practices that may arise during construction are picked up along
the way and rectified immediately before they become a much larger problem. In most
cases, it will be far more cost effective for all concerned if such problems are picked up at
this relatively early stage of a project rather than when works are complete – particularly if
they are “in ground” problems that subsequently get “built over” in the natural course of
events.
13.10 Progress payments and retentions

Most tennis court contractors will request that progress payments be made when certain
project milestones are reached or at recurring regular time intervals (i.e. fortnightly or
monthly) rather than one lump sum at the completion of all works. This is considered to
be a fair arrangement for all parties, as it provides the contractor with a degree of security
that they are getting paid for the work they are doing and also assists their business
cashflow (otherwise, a contractor could be out of pocket for many weeks or months for
aspects of the works they have completed and paid for at the start of a project).
From a court owner’s point of view, it allows them to plan ahead for when these payments
are required to be made. It also provides some leverage against the contractor to ensure
they are completing all the works required to achieve each of these milestones.
Most contracts require that retention monies are set aside in each progress payment as a
form of security for the owner should there be any defective, omitted or unfinished works

by the contractor at the completion of the project and any agreed Defects Liability Period
(see the “Repairs under warranty” discussion following this section). Generally 10% of
each progress payment, until a total amount equating to 5% of the original contract sum
is reached, is set aside in a separate account that no one party to the contract can
access without the approval of the other.
If no recourse or claim is made against these monies by the owner following the
completion of the Defects Liability Period then this money is, by default under the
contract, due and payable to the contractor. Conversely, if the Contractor fails to repair
any identified defective works or complete any omitted items, these monies could be
used by the owner to undertake these works, although legal advice should be sought
before taking such actions should there be potential that the contractor may object to this
course of action.
13.11 Repairs under warranty

Most contracts should incorporate a Defects Liability Period of some reasonable time
period to allow for any defective works that may not initially be evident at the completion
of a project to be identified and subsequently rectified by the Contractor. For smaller or
single court projects, this time period is typically six months, but for larger projects or
complete complexes, a twelve month period is normal.
The Defects Liability Period does not commence until it has been agreed that the project
has reached Practical Completion. Practical Completion is achieved when all aspects of
the project have been completed and it is considered ready for use and fit for purpose.
This status may be granted where the works are essentially completed except for some
small item which although specified is not critical for the functioning of the works.
An example of this would be where all works were completed except the supply of a
specified leaf sweeper for the court was delayed by a week due to a misplaced order by
the manufacturer. In this case, Practical Completion could be granted for the project,
subject to the supply of this outstanding item as soon as possible
Notwithstanding this contractual timeframe for identification and rectification of defects
under the contract, there remains recourse available to the owner under general building
common law for any defects that do not become evident during a Defects Liability Period.
For a claim of this nature to be successful, however, legal action would need to be taken
as soon as possible after the identification of such a defect, and it would have to be
proven that the cause of the defect was through the actions of the contractor in their
performance of the contract.
It should be taken into account before launching such legal action that taking such
matters before a court of law is not an inexpensive exercise. The legal costs may well
exceed the value of the damages being sought. In such instances, initial negotiations
should be conducted with the contractor with regards to rectifying any such identified
defects. If this proves unsuccessful, other avenues of less costly dispute resolution
should be attempted prior to taking any legal action (i.e. mediation, independent
assessment or arbitration – although some forms of arbitration may be as expensive as
taking traditional court action).
Generally, such claims in construction circumstances cannot be made after a period of
seven years has elapsed from the date of Practical Completion of the project.
An initial site inspection and independent assessment can be provided by your local
affiliated body in your state or territory (i.e. Tennis Queensland) at little or no cost. As
stated at the commencement of this chapter, these bodies have access to experts in all
facets of tennis court construction and are capable of very quickly identifying the cause/s
of almost all construction and maintenance failures.
With specific regards to court surface finishes, such as the various cushioned acrylic
products and artificial grasses or clays, the installers of such products will generally offer
substantial warranty periods for the materials and labour associated with their products.
Generally, these manufacturers are quite reasonable when honouring any claim against
their product for fear of any tarnishing of their reputation in the market-place. However,
there are usually some basic conditions that are applied to their warranties before any
claim against them can be made.
Such basic conditions include:
• the product needs to have been installed by the contractor in accordance with the
manufacturer’s recommendations
• the finished product needs to have been maintained and used in accordance with
the manufacturer’s recommendations
• no responsibility will be held against the surface finish manufacturer if their
product is damaged by failures of the base and/or sub-base constructed by
others.
Warranties offered for other elements of tennis court construction, such as fencing, net
posts, nets and other court furniture will also follow the same warranty principles as
outlined above for court surfaces.

14 Care and maintenance of tennis courts
14.1 General maintenance

A well constructed and well maintained tennis court will offer years of safe and trouble
free play. To maximise the useful life of any type of court, the owner should develop and
implement a regular schedule of maintenance. Regular inspection of the court[s] and
repair of minor problems is more cost effective than allowing the court to deteriorate to
the point where major rectification is required.
The most important step in maintaining all types of court surfaces is to keep them clean
by removing debris immediately, and spot cleaning spills as they occur.
Provide rubbish bins and encourage players and spectators to keep the surface clean.
Practise preventative maintenance by prohibiting food and beverages [except water] on
the court area, and declare the premises a non-smoking area.
Request, via signage, that the appropriate footwear is to be used on the courts at all
times. Watch for dirt and mud that may be tracked onto the court, and have a program to
remove accumulated dirt. A dirty court will wear prematurely, as well as cause variations
in ball bounce behaviour and be generally unattractive to potential court users.
The amount of maintenance required for any particular facility will vary according to
geographic location, amount and type of use etc. In any event, the owner should develop
a regular maintenance program. It will be cheaper in the long run. Remember there is no
such thing as a court that requires no maintenance. A well maintained court will look
better, play better, and give many years of satisfaction to all users.
14.2 Hard court and cushioned hard court maintenance

For a commercial facility or club, daily removal of debris and dust should be carried out
using a power blower. Private courts will not require this amount of attention; however
debris should not be allowed to accumulate.
All courts should be power washed at least once a year. Care must be exercised with
power washing so that the water jet does not damage the surface. The water blaster
nozzle should be held about 300mm clear of the surface. Start at the high end of the
court, and walk to and fro across the court until the wash terminates at the low end of the
court.
The washing exercise is a good time to pick up any nicks, holes, depressions or small
laminations in the surface which should be repaired as soon as possible.
Hard courts and cushioned hard courts can suffer from mildew or algae in shaded areas,
or areas that hold water for periods of time. The best way to remove this is to first
dampen the surface, then apply a 1 part bleach or chlorine / 5 parts water solution and
allow it to sit for 10 – 15 minutes. Do not apply excess solution or allow the solution to
work its way across the court surface, as what appears to be a stain will develop – it is
actually cleaning the surface. The solution should be thoroughly hosed off as soon as
possible, and the algae removal process confined to the affected area. A court with a lot
of algae contamination will require a total clean and wash. The runoff solution may need
to be collected and environmentally disposed of.
Acrylic courts can also suffer from tree sap, bird and flying-fox droppings. These should
not be allowed to remain on the surface, as they can cause laminations to occur. It is not
advisable to have trees close to or overhanging the court.
Over time, acrylic courts will show signs of use and wear, particularly around the
baselines. Racquet chips will become evident, and the surface may appear shiny, as
constant sandshoe movement polishes the surface.
A regular maintenance program for a tennis club would be to plan for resurfacing every 5
– 7 years. A well looked after private court with much less use will last longer.

It is a good idea to develop a program to inspect each court for signs of surface
blemishes at least monthly. Repairs if required can then be carried out. Make sure you
use, or have a contractor use recommended crack repair and filler materials for all
surface repairs. Warranties will be voided if incorrect products are used.
If a monthly court inspection is carried out, look for the following:
• Build up of debris, dust etc that may prevent proper run-off drainage at the low
point of the court.
• Any signs of cracks appearing
• Any depressions developing that may
hold water after rain. Any depression
holding water greater in depth than
2mm [20c coin] when the rest of the
court surface is completely dry should
be filled and repaired by a qualified
court contractor.
• Check for bubbling or blistering of the
surface. This will be clearly evident when the surface is wet just after rain.
• Watch for vegetation growing onto or into the court surface. A 50 – 100mm
border around the perimeter should be kept free of vegetation to prevent court
damage.
14.3 Indoor acrylic surfaces

Indoor surfaces accumulate dust, ball fuzz and dirt tracked in by players. Courts can be
cleaned [on a daily basis for high usage courts] with an industrial vacuum or rotary
sweeper. Once a month the courts should be cleaned with a water vacuum or water
brush unit.
Indoor courts may also develop a mould or fungus that can be cleaned off with a mild
bleach solution.
Stains on courts can be removed with a cold water detergent solution and a soft bristle
brush.
14.4 Hard court maintenance equipment

Equipment to quickly remove water is essential. These items will include squeegees
and/or foam rollers. Most facilities are using squeegees, but care needs to be taken to
ensure the rubbers are regularly replaced. An old squeegee will cause damage and
premature wear to the court surface, as occasionally the metal frame will strike the
surface. Foam rollers are less damaging, but these need to be hung up after use or they
will deform and not operate properly. Always look to have at least two (2) squeegees or
rollers per court to speed up water removal.
Power blowers are essential to quickly remove debris and make the courts attractive and
presentable each day. Make sure blowers are not operated outside of local authority
regulations.
A water blaster or “Gerni” is also a good piece of equipment to have for a larger facility.
Care should be exercised on the court surface where the water nozzle should not be
operated closer than 300mm from the surface. The water blaster can also be used to
clean pathways linking courts.
A small selection of trowels, paint brushes and a small amount of court surface materials,
line paint etc should be on hand to effect minor repairs. It is also a good idea to maintain
some replacement net posts, net post winders, nets and net straps so any damages can
be attended to immediately.
14.5 Sand filled synthetic grass maintenance

This topic is covered in Section 7.3.7 of this manual.
Sand filled synthetic clay maintenance
14.6 Grass court maintenance

Included in document by Peter Craven
14.7 Clay court maintenance

This topic is covered in Section 7.6.6 of this manual
14.8 Court equipment maintenance
14.8.1 Installing a tennis net.

Most nets have a 64mm – 76mm loop at both ends. When installing the net, one of these
loops has to be removed to enable it to be wound onto the internal winding mechanism.
Attach one loop to the anchor post, remove up to 400mm of vinyl coating on the cable at
the other end, and then attach to the winder.
Turn the mechanism until the net is some 50mm above the required height [914mm] at
the centre of the net. Do not over-tension the net cable, as it places a strain on the posts,
and causes an exaggerated reaction when the ball strikes the net band. If wooden dowels
are supplied with the net, then install them into the side bindings at each end.
Install the lacing cord by looping it through the grommets in the side bindings, and then
through the lacing base on the net post. Pull the net close to the post, and continue the
lacing down to the bottom of the post then tie it off.
Install the centre net strap and attach to the ground anchor. Adjust the height of the strap
to the correct height [914mm]. If the net is not over tensioned, there is no need to wind
the net down slightly overnight, as was the habit some years ago.
Nets come in varying heights ranging from 600mm [recommended for schools], to full
drop, with the bottom band resting on the court surface. This can result in premature
rotting of the stitches in the bottom band, and some debris accumulating on the bottom of
the net. The full drop net is preferable for championship play, but most tennis facilities
would be better served with a 760mm drop.
14.8.2 Net maintenance

Repair tears as soon as possible. Cables and headbands can be replaced, however it
usually results in the depth of the net being reduced by some 100mm. One headband
replacement is usually satisfactory, but as the net wears and develops holes again, it is
best to replace the net entirely.
14.8.3 Net post maintenance

Never over-tension the net cable. In a tennis facility with several courts, it is usual for the
winding handle to be removed so that staff are the people responsible for keeping the
nets at the desired tension and height.
Keep posts clean and touch up nicks and scratches on coated posts to prevent rust. Use
lubricating oil or gear lubricant on the winding mechanism. If a multi court facility, have a
few extra sets of internal winding mechanisms in store for quick replacement.
Older lever type winding gear or protruding winding handles should be replaced as they
present a player hazard.
Damaged or bent posts should be replaced. This is a simple matter if the post is sleeved,
and the sleeve foundation is properly installed. If the post is fixed or foundations have
moved, then the entire footing must be removed and replaced – not a simple job, as
damage to the court surface around the post itself must be minimised.
14.9 Windscreens and windscreen maintenance
14.9.1.1 Introduction
Windscreens serve many purposes, among these are:
• provide visual contrast for better ball definition
• reduce and/or deflect wind
• provide privacy and screen out distractions
• help tennis courts blend into their surroundings
• help contain artificial light at night.
To assist with the creation of a tennis garden, windscreens, in conjunction with carefully
selected shrubs, can provide a very attractive setting.
14.9.1.2 Choosing windscreens

For ball visibility, the darker the background, the better for ball definition. Therefore a fine
mesh in black or dark green is preferred. The preferred fabric where a windscreen and
sightscreen are the major requirements is a PVC coated polyester. The weave density
should be around 70%, which allows only 30% of the wind to flow through the fabric.
Fabrics with a greater density than 70% tend to create more wind turbulence on court.
A 70% mesh will give protection 10 times the height of the screen down court before the
wind regains its original velocity i.e. a screen 2 metres high offers protection 20metres
down court.
Where privacy is of greater concern, a more tightly woven fabric can be utilised. This,
however, will create turbulence, and is more suited to a domestic situation.
Quality windscreens have a life expectancy of between 8-12 years. The preference is for
the use of plated D rings in attaching the fence rather than brass eyelets. The D ring
gives much greater tensile strength, and it will withstand extreme wind conditions. The D
ring is used in conjunction with galvanised or stainless steel springs that attach to the
fence. This allows for a flexing action with wind gusts.
14.9.1.3 Installation
When installing windscreens, a number of
major considerations need to be taken into
account regarding fence construction.
First is to ensure that fence posts are of
sufficient strength to accommodate the
additional stress load caused by the
installation of screen to the fence.
Our experience backed by test results from
CSIRO show that a wind screen
measuring 1.83metres high and
constructed from 70% mesh, will increase
the stress load on a fence by 120kgs per lineal or running metre. It is therefore
imperative that stronger, larger, diameter fence posts be specified to avoid possible fence
damage during periods of high winds.
Fences with top and bottom support rails should also be considered. Apart from the
improved appearance, fences with support rails are generally more stable, making
installation of screens easier and with improved results because the fence wire does not
tend to curl up as much.
Where fences have already been erected, there are a number of alternative methods of
reinforcing fence posts which can be considered. The most common, if space permits, is
conventional gooseneck backstay, which is the most simple and least costly to install.

The second alternative is to place an additional post alongside the existing one. When
coupled together, this method is as effective in stabilising the fence as a gooseneck
backstay, with the added advantage of taking up less ground space.
The position of the support strand wire on the fence is also of importance. Screens are
installed approximately 300mm off the court surface, and as the height of the screen
measures 1.83metres, the ideal position of the bottom and top strand of wire would be
180mm for the bottom strand, and 2.15metres for the top strand. This allows attachment
of the springs to a stable fixing point which does not flex when the wind is gusting, and
would eliminate the problem of springs falling off due to the chain mesh stretching.
14.9.1.4 Maintenance
Preventative maintenance should be carried out regularly by replacing springs if they
have fallen off or stretched, as failure to do so may result in damage to the screens if left
flapping in the wind. Quality screens are designed to be installed under tension so the
screens are quite tight. It would be wise to carry spare springs for emergency.
Planning is important for the installation of windscreens at a time prior to the court being
constructed. If this is done, not only will you have saved money, but the completed job
will be more professional, and conditions on court will be greatly enhanced by the correct
installation of windscreens.
14.9.1.5 Checklist when installing court screens

• Fences need to be looked at before screens are installed
• Back stays should be installed on every upright
• Old fences could have extra strand wires along bottom of fence and at point where top
of screens are to be hung
• Top and bottom rails make the chain mesh far more stable, therefore giving a better
foundation for screens to be installed
• Do not hang screens too close to bottom of fence, as this will make fence curl up at
bottom. Position 300mm-400mm from bottom of chain mesh
• Make sure chain mesh is adequately tied onto the uprights, otherwise chain mesh can
be distorted
• Screens are designed to be put up under tension to reduce flapping and minimise the
possibility of springs falling off
• Keep a box of springs available to replace lost or stretched springs
• Endeavour to replace springs as soon as possible to reduce the possibility of screens
flapping about and causing damage to the screens
• If screens are damaged, remove from fence and have them repaired.
14.10 Landscape maintenance

Firstly, be very selective in the type of landscaping to
use around a tennis court.
Avoid large trees and aggressive root systems, as
these will cause heartache in future years. Keep
shrubs well away from court fencing as leaves and
other debris will accumulate, and require regular
sweeping or blowing off the court surface.
A once weekly walk around the tennis facility will pick
up on areas that require attention. If a watering
system is installed, turn it on occasionally to check that the sprinkler heads are operating
effectively.

Choose shrubs and plants that require minimal amounts of water, but also ensure they
are compatible with soil and climate conditions. Keep the landscaping tidy, and be
prepared for some pruning, fertilising and replacement when the need arises. Have
unobtrusive rubbish bins around the facility to deposit food and drink containers.

15 Document control
15.1 Date of preparation

The collation of information took place over many months prior to the release of this draft
version of this manual. This initial draft was placed on Tennis Queensland’s web site for
comment and feedback in December 2006 and as such this document will be
continuously updated in the following months until Tennis Queensland is satisfied that the
document is suitable for official release.
15.2 Review date.

Whilst this document remains in a draft format, it will essentially be a live document that
will be updated at least monthly, or more frequently if required. Once it has been officially
released, it is anticipated than an annual review and updated version would be produced
and issued. If the changes in any one year are considered very minor, a small
supplement or update could be issued summarising these changes which could then be
inserted into the current document rather than re-issuing or reprinting the whole manual.
15.3 Disclaimers
As stated in the Introduction (Section 1) of this manual, the information contained herein
should not replace the advice that should be sought and provided by professionals such
as engineers, architects and registered court builders. This manual has been primarily
produced to provide members of the tennis community with assistance to understand the
concepts and technical aspects of tennis court construction and maintenance.

16 APPENDICES
Glossary of terms
ITF International Tennis Federation. This is the governing body of the sport and
establishes rules for the game and the facilities.
TA Tennis Australia – administrator of the sport nationally.
TQ Tennis Queensland – administrator of the sport in Queensland.
Banked Courts multiple courts on a single platform. Often banked courts share a
surrounding fence and are separated from each other with low height or no
dividing fences. The practice of omitting dividing fences is not encouraged due to
the risk of injury to players from stray balls and the consequential litigation issues.
Links to other sources of information have been provided throughout the body of this
document where applicable and relevant, rather than as a summary in this Section of the
manual.
The following pages include:

• Current “Plexipave” and “Plexicushion” brochures
• A current Rebound Ace Colour Selection Chart for information as referenced in
the body of this document.

Technical Manual

Uploaded by

Document Informationclick to expand document informationTechnical Manual Tennis Courtyard

Document Informationclick to expand document information

Copyright:

Available Formats

Technical Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Technical Manual

Uploaded by

Copyright:

Available Formats

TECHNICAL MANUAL

For the Design, Construction and

Compiled by the Tennis Queensland

Second Edition – June 2008

© Tennis Queensland, 2008. All rights reserved.

All correspondence concerning this publication should be addressed to:-

The Technical Services Advisory Group

c/- Tennis Queensland

Graceville, QLD, 4075

Printed by Tennis Queensland, Brisbane, Australia

1.2 Purpose of the manual

1.3 Information sources, Standards and Codes.

1.4 Where to get further help

2.4 Choosing a site

Recommended court size (ITF full size court)

2.6 Court construction on a “greenfield” site

2.6.1 Asphalt base – acrylic surface

2.6.2 Concrete base

Standard Average Uniformity

3.2 Definitions used in this section

3.3 Project Management

3.5 Ongoing costs

3.6 Information sources, Standards and Codes.

4.2 Definitions used in this section

4.3 Choice of site

4.4.1 Slip areas

4.4.2 Uncontrolled fill and other issues

4.4.3 Future growth

4.5 Court planning

4.5.1 Court dimensions

4.7 Overland flow of water and drainage

4.7.1 Surface water.

4.7.2 Subsurface water

4.8 Choice of contractor

5.2 Definitions used in this section

5.3 Site investigation

5.4 Soil report

5.5 Underground flow of water and drainage

5.7.1 Types of walls

5.8.1 Control of vegetation

6.2 Definitions used in this section

Asphalt batching Manufacturing facility at which asphalt is produced prior to delivery

6.4 Elements common to all bases.

6.5 Asphalt bases

6.5.1 Elements of an asphalt base

6.5.2 Construction process

6.5.3 Construction failures.

6.5.5 Measures of quality.

6.6 Concrete bases

6.6.1 Types of concrete bases

6.6.2 Reinforced concrete bases

6.6.4 Post Stressed concrete bases

6.8 Proprietary base systems

6.8.1 Chemically bound systems

6.9 Maintenance and repair of base structure

6.10 Information sources, Standards and Codes.

7.1.1 Definitions used in this section

7.1.2 Classification of surface systems