EN - Julie 14 Renault

1
Back to the Contents
Julie - Universal Car Emulator Programs:

Immo programs
Renault with CAN - ver 2..................................................................................................3
Renault with CAN - ver 1................................................................................................15
ESL 1...............................................................................................................................31
ESL 2...............................................................................................................................33
Renault without CAN......................................................................................................36
Renault without CAN old ECUs.....................................................................................36
Program Use
EDC 16
EDC16 with separate flash
Siemens SIM32
Renault with CAN - ver 2 Delpi DCM1.2
Sagem S3000
Delphi DCM3.4
EMS3110
Siemens SIM32
Sagem S2000
Sirius 32 / Sirius 34 with CAN
Renault with CAN – ver 1
Delphi DDCR with CAN – 95080 memory
3-socket Bosch EDC15 with CAN – 5P08C3
EMS 3132/ EMS 3134 with CAN
ESL 1 • ESL 1
ESL 2 • ESL 2
• Sirius 32 / Sirius 34 without CAN
• EMS 3132 / EMS 3134 without CAN
• 1.9 2.2 and 2.5 dCi without CAN
• Delphi DDCR
Renault without CAN
• 1.9 dTi 1 plug
and
Renault without CAN – old ECUs • 1.9 dTi 2 plugs
• 1.9 diesel DCU3
• 2.8 TD
• 1 plug with 24C02 memory
• Volvo S40 and V40 – 1.9 TD Bosch ECU
You can buy our products and obtain technical support from our distributor. Find a distributor
near you by clicking on the link: www.carlabimmo.com/our-partners
2
Wiring colour codes
The LED behavior
- no jumpers – diagnostic mode - it flashes every second
- adjusting to the ECU – flashing 0,1 sec
- after adjusting it lights constantly and blinks every other second
3
Immo programs
Renault with CAN - ver 2
In Universal Julie Emulator

solder jumpers J1, J2 and J6
Emulator will work, when diagnosis goes

along CAN
If the emulator doesn't work, solder jumpers J2 and J6
USE
EDC16
SIEMENS SIM32
DELPHI DCM1.2
SAGEM S3000
DELPHI DCM3.4
EMS3110
4

Renault with CAN ver 2
EDC16
EDC16 v1 EDC16 v2
Connecting emulator to ECU
5

If you use CAN emulator:
1. Cut CAN-L line from the ECU plug.

2. Put the switch-key inside the cabin by the ignition switch.
3. After inserting the key, disconnect with CAN-L switch and start the ignition.
4. Short it with CAN-L switch and start the car.
5. That is a security switch, so that you can start the car safely.
EDC16 v1 EDC16 v2
Find Eeprom memory in ECU
6

1st possible change of memory
Find repeated values from 062 to 075

addresses and change this values into
8C 0F 94 33 E7 14 D9 5A C1 66 B2 41
26 A5 3E 99 4D BE F7 87 in all eeprom
memory content
2nd possible change of memory
Find repeated values from 06E2 to 06F5

8C 0F 94 33 E7 14 D9 5A C1 66 B2 41
memory content
7

3rd possible change of memory
Find repeated values from 9C2 to 9D5

8C 0F 94 33 E7 14 D9 5A C1 66 B2 41
memory content
4th possible change of memory
Find repeated values from 0A62 to 0A75

8C 0F 94 33 E7 14 D9 5A C1 66 B2 41
memory content
For Nissan Interstar ECU 0 281 012 200 cut pin D3 from connector "A" (middle connector).
This is the CAN L line!!!
8

SIEMENS SIM32
Click on the thumbnail to watch the video
Find 63F7055 RENESAS flash memory in ECU
In the addresses from 880 to 885

write 8C 0F 94 33 E7 14 values
9

ATTENTION!
EMULATOR WORKS ONLY WITH ECUS WHICH HAVE NO RESISTOR
IN PLACE MARKED ON THE PHOTO.
10

DELPHI DCM1.2
Find 95160 memory
11

In 95160 memory in the addresses from

00 to 1F change values into 00
SAGEM S3000
12

DELPHI DCM3.4
13

In Eeprom memory in the address 040

to 047 change values into
14 E7 33 94 0F 8C 02 5E
EMS3110
14

In MPC processor in the addresses from

1C00 to 1C0B change values into
8C 0F 94 33 E7 14 73 F0
6B CC 18 EB
15
Renault with CAN - ver 1

solder jumpers J2 and J6
Emulator will work, when diagnosis goes

along K-line
If the emulator doesn't work,

solder jumpers J1, J2, and J6
USE
SIEMENS SIM32
SAGEM S2000
SIRIUS 32 / SIRIUS 34 with CAN
Delphi DDCR with CAN - 95080 memory
3-socket BOSCH EDC15 ECU with CAN - 5P08C3 memory
EMS 3132 / EMS 3134 with CAN
16

If you use CAN emulator:
1. Cut CAN-L line from the ECU plug.

2. Put the switch-key inside the cabin by the ignition switch.
3. After inserting the key, disconnect with CAN-L switch and start the ignition.
4. Short it with CAN-L switch and start the car.
5. That is a security switch, so that you can start the car safely.
SIEMENS SIM32
Find 63F7055 RENESAS flash memory in ECU
17

In the addresses from 880 to 885

write 8C 0F 94 33 E7 14 values
ATTENTION!
EMULATOR WORKS ONLY WITH ECUS WHICH HAVE THE RESISTOR
IN PLACE MARKED ON THE PHOTO.
18

SAGEM S2000
Find Eeprom 95080 memory in ECU
In the addresses:
001 write 03 value,
003 write FC value,
011 write 08 value,
013 write F7 value,
and
from 110 to 115 write 0F 8C 33 94 14
E7 values, and
from 118 to 11C write 96 49 8A D2 01
values, and
from 126 to 127 write 85 DB values
Second changes (some models)
In the addresses:
from 0F0 to 0F9 write 0F 8C 33 94 14
E7 44 3E 04 4E values, and
from 0FD to 0FF write 01 5F 6B values
19

Third change
In the addresses:
from 0D0 to 0D9 write 0F 8C 33 94 14
E7 44 3E 04 4E values, and
from 0DD to 0DF write 01 5F 6B values
20

SIRIUS 32 with CAN
Find 29F200 or 29F400 flash memory in ECU
In the addresses from 4000 to 7FFF, find

all 64 C7 or 54 D7 values
and change these values and two units
before them into FF FF FF FF
Repeat it in the whole map from 4000 to

7FFF!!!
In order to start the starter you need to join two pins of starter's relay!
21

SIRIUS 34 with CAN
Tested on SIRIUS 34 ECUs
S118301104 A
S118301109 A
S118301110 A
S118301111 A
S118301113 B
S118301118 A
S118301220 C
S118301305 F
S118303106 A
S118303109 A
S118303425 A
Find 29F200 or 29F400 flash

all values 64 C7 or 54 D7

7FFF !!!
22

Take power for the emulator from the capacitor at the flash
Delphi DDCR with CAN - 95080 memory
23

First connecting Second connecting
Find 95080 memory
In address from 00 to 01F

write 00 values
Also tested and working on:
ECU 8200331477 with CAN Emulator

Nissan Kubistar 1.5 diesel, production year: 2004 and 2006
24

3-socket BOSCH EDC15 ECU with CAN - 5P08C3 memory
EDC15 – old EDC15 – new
EDC15 – new v2
25

Find 5P08C3 memory
In address from 1E7 to 1E8

and from 1EE to 1EF write 00 00 values
26

Other EDC15 ECUs
Find 5P08C3 memory
In address from 1E7 to 1E8

and 1EE to 1EF write 00 00 values
It is possible to disconnected CAN from

ECU
If there are VIN number

in memory content
use Renault with CAN ver 1 program
27

Tested and working on the following ECUs:

0 281 001 934
0 281 010 297
0 281 010 482
0 281 010 556
0 281 010 632
0 281 010 633
0 281 010 637
0 281 011 039
0 281 011 101
0 281 011 137
0 281 011 324
0 281 011 432
0 281 011 529
0 281 011 530
0 281 011 562
0 281 011 571
0 281 011 723
0 281 011 890
0 281 011 940
0 281 011 969
0 281 013 923
EMS 3132 with CAN
28

Find 29F200 flash


7FFF!!!
Every time you want to start the car,

you have to turn the keys in the
ignition TWICE before it starts!
EMS 3134 with CAN
29

Tested on EMS 3134 ECUs
S118301122 A
S118301122 B
S118301123 A
S118301124 A
S118303122 A
S118303122 B
S118303123 A
Find 29F400 flash
30



7FFF!!!
Every time you want to start the car, you have to turn the keys in the ignition TWICE before
it starts!
Emulator tested on vehicles:
SIRIUS 32 - Clio 1.2 8V 2001

Renault Megane II / Clio II 1.5 DCI
Renault Trafic 1.9DCI 2004
Nissan Primastar 1.9 DCI 2001 - 03
Opel Vivaro 1.9DCI /2.5DCI 2004
Renault Master 2.5DCI 2002
Renault Laguna II 1.9DCI/ 2.2DCI
Renault Megane II 1.9DCI
Nissan Kubistar 1.5 diesel 2004 and 2006
31
ESL 1

solder jumpers J2, J3, J4, J5 and J6
ESL connection
ESL - connection
32

Renault ESL
USE
Renault Megane II,

Renault Laguna II,
Renault Scenic II,
Renault Clio III,
Renault Espace IV (Phase II)
Click on the thubnail to watch the video
Correct functioning of the steering wheel lock:
1. The diode on the tachometer blinks fast

2. Insert the card into the slot.
3. The lock is removed
4. The engine can be started using 'Start&Stop' Button.
Damaged steering wheel lock:
1. The diode on the tachometer blinks fast (no card or wrong card)
2. Insert the card into the slot. The diode lights continuously.
3. The car does not respond to the 'Start&Stop' Button, the ignition cannot be switched on.
We are sure that the lock is damaged.
33
ESL 2 – first soldering

solder jumpers J1, J2, J3, J4, J5 and J6
ESL 2 – second soldering

If the emulator doesn't work, do the following:

solder jumpers J1, J2, J3, J4, J5, J6, and CAN
120R
34

Renault ESL 2
ESL 2 - first connection
ESL 2 Connection
If the emulator doesn't work, do the following:
ESL 2 - second connection

Put a 100Ω resistor on pins 2 and 4
ESL 2 Second Connection
USE
Renault Talisman
Renault Captur
Renault Megane III,
Renault Clio IV,
Renault Scenic III,
Renault Fluence,
Renault Laguna III,
Renault Espace IV (Phase III and later)
35
Correct functioning of the steering wheel lock:
1. The diode on the tachometer blinks fast

2. Insert the card into the slot.
3. The lock is removed
4. The engine can be started using 'Start&Stop' Button.
Damaged steering wheel lock:
1. The diode on the tachometer blinks fast (no card or wrong card)
2. Insert the card into the slot. The diode lights continuously.
3. The car does not respond to the 'Start&Stop' Button, the ignition cannot be switched on.
We are sure that the lock is damaged.
36
Renault without CAN

solder jumpers J2, J3, J4 and J5
Renault without CAN old ECUs

solder jumper J5
SIRIUS 32 / SIRIUS 34 without CAN

EMS 3132 / EMS 3134
1.9 2.2 and 2.5 dCi without CAN
Delphi DDCR
1.9 dTi 1 plug
1.9 dTi 2 plugs
1.9 diesel DCU3
2.8 TD
1 plug with 24C02 memory
Volvo S40 and V40 – 1.9TD (Bosch 0 281 001 906 ECU)
37

Renault without CAN
SIRIUS 32 without CAN

all values 64 C7 or 54 D7 or B4 5C
Repeat it in the whole map from

4000 to 7FFF !!!
38

Renault without CAN
Take power and GND for the emulator

from the capacitor
Connect Code signal after desoldering a

333 resistor
If there is A82C250 CAN transducer

on the plate in the ECU, then the
emulator will not work in this ECU!!!
SIRIUS 34
39

Renault without CAN
Tested on SIRIUS 34 ECUs
S118301104 A
S118301104 B
S118301211 B
S118301211 C
S118301212 B
S118301213 B
S118301213 C
S118301216 B

all values 64 C7 or 54 D7 or B4 5C

7FFF !!!
Take power for the emulator from the capacitor at the flash
40

Renault without CAN
EMS 3132
In the addresses from 4000 to 7FFF, find all values

64 C7 or 54 D7 or B4 5C
and change these values and two units before them
into FF FF FF FF
Repeat it in the whole map from 4000 to 7FFF !!!
Take power for the emulator from the capacitor at the flash.
41

Renault without CAN
Connect green wire as pictured after

unsoldering 333 resistor and connect it
to the point which leads to the processor.
EMS 3134
42

Renault without CAN
Tested on EMS 3134 ECUs
S118301120 B
S118301124 A
Find 29F400 flash
In the addresses from 4000 to 7FFF, find all values

64 C7 or 54 D7 or B4 5C
and change these values and two units before them
into FF FF FF FF
Repeat it in the whole map from 4000 to 7FFF !!!
Connect green wire as pictured to 88 pin and cut it off from wiring.
43

Renault without CAN
1.9 2.2 and 2.5 dCi without CAN
EDC15 - old
EDC15 - new EDC15 - new v2
44

Renault without CAN
In 5P08C3 memory
in the addresses:
003E 003F 0040 0041
and
0044 0045 0046 0047
change these values into FF
If there are VIN number

in memory content
use Renault with CAN ver 1 program
In ECU, solder immo line (code) of

emulator to the point as pictured
Take power for the emulator from the

capacitor on the ECU plate
45

Renault without CAN
Unsolder 334 resistor
Turn on the ignition for 30 seconds,then turn it off for 30 seconds and repeat the procedure a
few times
DDCR
46

Renault without CAN
Car without tachometer
Replace 25080 content and connect emulator.
10 pin of processor is immo line as pictured, which must be raised.
Take power from the capacitor at the memory.
Code injectors and settings with Clip or Launch.
ECU HOM8200334540
Use Julie as Renault without CAN program. Solder jumpers J2, J3, J4, and J5
Tested on:
Suzuki Jimny 1.5 diesel 2004
Nissan Almera 1.5 diesel 2004
1.9 dTi 1 plug
47

Renault without CAN
Connect the immo line of emulator to

pin 59 of ECU.
Connect GND and ACC to diode in the

ECU.
Bend pin 59 in ECU socket
48

Renault without CAN
1.9 dTi 2 plugs
In the addresses from 174 to 177 and

1B7 to 1BA
change these values into FF FF FF FF in
24C04 memory
49

Renault without CAN
Cut off pin 15 from wiring!!!
1.9 diesel DCU3
Renault Kangoo 1.9 Diesel 2001
50

Renault without CAN
In addresses from 02 to 05 and 82 to 85

change these values into 00 00 FF FF in
95080 memory
Pin 20 must be bent in socket or cut off from the car wiring.
51

Renault without CAN
2.8 TD
(Renault Mascott)
In addresses from 040 to 1FF change these values into FF in 24C16 memory
52

Renault without CAN
53

Renault without CAN
1 plug with 24C02 memory

(Renault Laguna)
Cut off pin 50 from ECU!!!
In addresses from 05A to 05F and

from 0F2 to 0F7 change these values
into FF in 24C02 memory
54

Renault without CAN
Volvo S40 and V40 – 1.9TD (Bosch 0 281 001 906 ECU)
MSA 15.5-5.40
In addresses from 03F to 041 and from

054 to 057
change these values into 00 00 FF FF in
24C02 memory
55
Warning!!!
Due to possible construction changes of cars, check signals with multimeter in the ECU plug.
All rights reserved.

Unauthorized copying, hiring, lending, public performance will be punished!
We state that we are the only authentic authors of this manual. We possess copyright of this
publication. Any trials of unauthorized copying, hiring, quoting prohibited!!! Both service and
advertisement constitute copyright and they are the subject to the protection in accordance with the
Act from 4th Feb. 1994 on Copyright and Related Laws (Statute Book no. 24 position 93) and
protection on the basis of the Act from 8th June 1993 on combating an unfair competition (Statute
Book no. 47 position 211)
www.carlabimmo.com
Last updated 29.01.2018

EN - Julie 14 Renault

Uploaded by

Copyright:

Available Formats

EN - Julie 14 Renault

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

EN - Julie 14 Renault

Uploaded by

Copyright:

Available Formats

What are the different types of Renault ECUs discussed in the document?

What are the different types of Renault ECUs discussed in the document?

What steps are involved in connecting a CAN emulator to an ECU?

What steps are involved in connecting a CAN emulator to an ECU?

1

Back to the Contents

Julie - Universal Car Emulator Programs:

Back to the Contents

Wiring colour codes

The LED behavior

- no jumpers – diagnostic mode - it flashes every second

- adjusting to the ECU – flashing 0,1 sec

- after adjusting it lights constantly and blinks every other second

Back to the Contents

Renault with CAN - ver 2

In Universal Julie Emulator

Emulator will work, when diagnosis goes

If the emulator doesn't work, solder jumpers J2 and J6

Back to the Contents

Connecting emulator to ECU

Back to the Contents

If you use CAN emulator:

1. Cut CAN-L line from the ECU plug.

EDC16 with separate flash

Find Eeprom memory in ECU

Back to the Contents

Connecting emulator to ECU

1st possible change of memory

Find repeated values from 062 to 075

2nd possible change of memory

Find repeated values from 06E2 to 06F5

Back to the Contents

3rd possible change of memory

Find repeated values from 9C2 to 9D5

4th possible change of memory

Find repeated values from 0A62 to 0A75

Back to the Contents

Click on the thumbnail to watch the video

Find 63F7055 RENESAS flash memory in ECU

In the addresses from 880 to 885

Back to the Contents

Connecting emulator to ECU

Back to the Contents

Click on the thumbnail to watch the video

Find 95160 memory

Connecting emulator to ECU

Back to the Contents

In 95160 memory in the addresses from

Connecting emulator to ECU

Back to the Contents

Connecting emulator to ECU

Back to the Contents

In Eeprom memory in the address 040

Connecting emulator to ECU

Back to the Contents

In MPC processor in the addresses from

Back to the Contents

Renault with CAN - ver 1

In Universal Julie Emulator