MR453X7917B050 PDF
MR453X7917B050 PDF
MR453X7917B050 PDF
17B
PETROL INJECTION
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
Fault finding Introduction
Fault finding List and location of components
Fault finding Role of components
Fault finding Operating diagram
Fault finding Features
Fault finding Replacement of components
Fault finding Fault summary table
Fault finding Interpretation of faults
Fault finding Conformity check
Fault finding Status summary table
Fault finding Interpretation of statuses
Fault finding Parameter summary table
Fault finding Interpretation of parameters
Fault finding Command summary table
Fault finding Customer complaints
Fault finding Fault Finding Chart
Fault finding Test summary table
Fault finding Tests
17B - 2
17B - 3
17B - 4
17B - 5
17B - 9
17B - 12
17B - 15
17B - 17
17B - 90
17B - 91
17B - 92
17B - 109
17B - 111
17B - 141
17B - 143
17B - 145
17B - 173
17B - 174
V1
"The repair procedures given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The procedures may be modified as a result of changes introduced by the
manufacturer in the production of the various component units and accessories from
which his vehicles are constructed."
Edition Anglaise
All rights reserved by Renault s.a.s.
Copying or translating, in part or in full, of this document or use of the service part
reference numbering system is forbidden without the prior written authority of
Renault s.a.s.
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Introduction
17B
Program No.: 2A
Function(s) concerned:
Petrol injection,
Flex Fuel Injection
Ele. 1681
universal bornier
Mot 1711
Multimeter.
3. SAFETY INSTRUCTIONS
Safety rules must be observed during any work on a component to prevent any material damage or personal injury:
Make sure the battery is properly charged to avoid damaging the computers if there is a low charge.
Use the appropriate tools.
4. REMINDER
To run diagnostics on the vehicle computers, switch on the ignition using the key
To switch off the + after ignition feed, switch off the ignition using the key.
V42_V04_PRELI / V42_V06_PRELI
MR-453-X79-17B050$010.mif
V1
17B-2
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding List and location of components
17B
Injection computer:
The injection computer is located in the engine compartment, behind the battery.
TDC sensor:
This sensor is located on the gearbox casing, behind the engine.
Pinking sensor:
This sensor is located between the four injectors.
Refrigerant pressure sensor:
This sensor is located on the air conditioning circuit.
Injection coolant temperature sensor:
This sensor is located on the engine water chamber.
Injection air temperature sensor:
The air temperature sensor is located at the air circuit inlet.
Downstream oxygen sensor:
The downstream oxygen sensor is located on the exhaust pipe downstream of the catalytic converter.
Upstream oxygen sensor:
The upstream oxygen sensor is located on the exhaust pipe after the manifold.
Accelerator potentiometer:
The potentiometer is located on the accelerator pedal.
Brake light switch:
The switch is located on the brake pedal.
Injectors 1, 2, 3, 4:
The injectors are mounted on the engine.
Motorised throttle valve:
The damper valve is located in front of the inlet manifold.
Quadruple ignition coil module (D4D and K7M engines):
The coil module is located in the engine compartment.
Cylinder 1, 2, 3, 4 pencil coils (K4M engine):
They are located on the cylinder head.
Catalytic converter:
The catalytic converter is located on the exhaust pipe downstream of the catalytic pre-converter.
Fan unit relay:
The relay is located on the cooling radiator.
MR-453-X79-17B050$020.mif
V1
17B-3
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Role of components
17B
Injection computer:
The injection computer receives information from various sensors and sends control signals to various actuators
according to mappings that it has stored in the memory.
TDC sensor:
This sensor allows the computer to provide synchronisation as well as to know the position Top Dead Centre for
injection phasing.
Pinking sensor:
This sensor allows the computer to correct the ignition advance under high engine load to avoid damaging the
engine.
Refrigerant pressure sensor:
The role of the sensor is to measure the refrigerant fluid pressure in the air conditioning circuit.
Injection coolant temperature sensor:
The engine coolant temperature sensor informs the computer about the engine coolant temperature.
Injection air temperature sensor:
The air temperature sensor provides the computer with the temperature of air taken in by the engine.
Oxygen sensors:
The oxygen sensors allow the catalytic converter to correctly perform engine emission control tasks.
Accelerator potentiometer:
The potentiometer allows the computer to take into account driver requests expressed using the accelerator pedal.
Clutch pedal switch:
This switch allows the computer to convert to anti-jerking mode when the clutch pedal is depressed.
Brake light switch:
The brake light switch informs the computer of the brake pedal status.
Two gangs are used if the cruise control function exists.
Injectors:
These injectors enable rapid, precise metering of the quantity of fuel injected, with excellent injection process
repetitiveness.
Motorised throttle valve:
The throttle valve allows engine air flow to be managed according to driver requests.
Quadruple ignition coil module (D4D and K7M engines):
The ignition unit enables ignition (explosion timing control).
Cylinder 1, 2, 3, 4 pencil coils (K4M engine):
The pencil coils enable ignition (explosion timing control).
Fan unit relay:
The engine cooling fan unit relay supplies power to the engine cooling fan.
MR-453-X79-17B050$030.mif
V1
17B-4
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Operating diagram
D4D760
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Air filter
Motorised throttle valve
Injection air temperature sensor
Manifold pressure
Injectors
Ignition coils
Injection coolant temperature sensor
Pinking sensor
TDC sensor
Upstream oxygen sensors
Downstream oxygen sensors
Injection computer
Auxiliary cold starting system
Auxiliary fuel tank
Auxiliary fuel
Petrol/alcohol tank
Petrol pump
Bleed valve
MR-453-X79-17B050$040.mif
V1
17B-5
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Operating diagram
K4M694
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Air filter
Motorised throttle valve
Injection air temperature sensor
Manifold pressure
Injectors
Ignition coils
Injection coolant temperature sensor
Pinking sensor
TDC sensor
Upstream oxygen sensors
Downstream oxygen sensors
Injection computer
Auxiliary cold starting system
Auxiliary fuel tank
Auxiliary fuel
Petrol/alcohol tank
Petrol pump
Bleed valve
MR-453-X79-17B050$040.mif
V1
17B-6
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Operating diagram
K7M714
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Air filter
Motorised throttle valve
Injection air temperature sensor
Manifold pressure
Injectors
Ignition coils
Injection coolant temperature sensor
Pinking sensor
TDC sensor
Upstream oxygen sensors
Downstream oxygen sensors
Injection computer
Auxiliary cold starting system
Auxiliary fuel tank
Auxiliary fuel
Petrol/alcohol tank
Petrol pump
Bleed valve
MR-453-X79-17B050$040.mif
V1
17B-7
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Operating diagram
K4M606
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Air filter
Motorised throttle valve
Injection air temperature sensor
Manifold pressure
Injectors
Ignition coils
Injection coolant temperature sensor
Pinking sensor
TDC sensor
Upstream oxygen sensors
Downstream oxygen sensors
Injection computer
MR-453-X79-17B050$040.mif
V1
17B-8
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Features
17B
Engine immobiliser
This Verlog 2 type immobiliser function is managed by the UCH computer and the injection computer.
Before any starting request, the injection computer is protected.
When a starting request is made, the injection computer and the Passenger Compartment Control Unit (UCH)
exchange authentication data via the multiplex network. This determines whether the engine start is authorised or
denied.
After more than five consecutive failed authentication attempts, the injection computer goes into protection (antiscanning) mode and no longer tries to authenticate the UCH computer. It only leaves this mode when the following
sequence of operations is carried out:
the ignition is left on for at least 20 seconds,
the message is switched off,
the end of the injection computer self-feed is adhered to (the length of time varies depending on engine
temperature).
After this, one and only one authentication attempt is allowed. If this fails again, repeat the sequence of operations
described above.
If the injection computer still fails to unlock, contact the Techline.
Impact detected
If an impact has been stored by the injection computer, turn off the ignition for 10 seconds, then switch it back on to
start the engine. Clear the faults using the control RZ001 Fault memory.
WARNING
Disconnect the injection system computer when carrying out any welding work on the vehicle.
ENGINE SPEED MANAGEMENT
Engine speed management is based on the following programs:
MR-453-X79-17B050$050.mif
V1
17B-9
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Features
17B
MR-453-X79-17B050$050.mif
V1
17B-10
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Features
17B
MR-453-X79-17B050$050.mif
V1
17B-11
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Replacement of components
17B
MR-453-X79-17B050$060.mif
V1
17B-12
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Replacement of components
17B
If the data were not saved before the operation, carry out the following operations:
Programming the VIN code
Enter the V.I.N. using command VP010 Enter VIN.
Injector programming
Program the injectors by accessing the sub-section entitled Injector replacement operations.
Programming the TDC sensor
Program the TDC sensor by accessing the sub-section entitled TDC (Top Dead Centre) sensor replacement
operations.
Programming the motorised throttle
Program the motorised throttle by accessing the sub-section entitled Throttle valve replacement operations.
Injection computer initialisation
Start and stop the engine to initialise the computer and wait for the loss of communication message to appear on
the diagnostic tool, if the message does not appear, wait for 9 minutes.
The computer is automatically configured according to the sensors and options present on the vehicle.
MR-453-X79-17B050$060.mif
V1
17B-13
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Replacement of components
17B
MR-453-X79-17B050$060.mif
V1
17B-14
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault summary table
Tool fault
DTC code
DF001
0115
DF002
0095
DF011
0641
DF012
0651
DF015
0657
DF018
0480
DF026
0201
DF027
0202
DF028
0203
DF029
0204
DF038
0606
Computer
DF047
0560
DF050
0571
DF059
0301
Misfiring on cylinder 1
DF060
0302
Misfiring on cylinder 2
DF061
0303
Misfiring on cylinder 3
DF062
0304
Misfiring on cylinder 4
DF065
0300
Combustion misfire
DF078
2100
DF079
2119
DF081
0443
DF082
0135
DF083
0141
DF085
0627
DF088
0325
DF091
0500
DF092
0130
DF093
0136
DF095
0120
DF096
0220
DF101
C121
MR-453-X79-17B050$070.mif
V1
17B-15
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault summary table
Tool fault
DTC code
DF102
2503
DF109
0313
DF120
0335
DF361
1351
DF362
1352
DF394
0420
DF398
0170
DF409
0461
DF457
0315
Flywheel target
DF532
2502
DF556
2135
DF631
0703
DF648
060B
Computer
DF721
0217
Engine overheating
DF884
2632
DF887
0226
DF894
1633
DF974
0225
DF975
2120
DF992
1644
DF993
1645
DF994
1646
DF1015
0504
DF1017
061A
Computer
DF1058
0106
DF1063
C415
DF1068
0530
DF1072
0645
DF1074
0638
DF1355
1656
*Refriger: refrigerant
MR-453-X79-17B050$070.mif
V1
17B-16
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF001
PRESENT
OR
STORED
17B
Special notes:
The OBD and Level 1 warning lights illuminate.
NOTES
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the connection and condition of the connector of the coolant temperature sensor, component code 244
and of the connections of the injection computer, component code 120.
If the connector(s) are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Disconnect the injection computer connector, component code 120 (see MR 388 or 451, Mechanical, 17B,
Petrol injection, Petrol injection computer: Removal - Refitting).
Measure the resistance of component 244 by connections 3JK and 3C of the injection computer connector,
component code 120.
If the resistance of the coolant temperature sensor, component code 244 is not between 100 X 10 k at
ambient temperature: replace the coolant temperature sensor, component code 244 (see MR 388 or 451,
Mechanical, 19A, Cooling, Coolant temperature sensor: Removal - Refitting).
Check the insulation, continuity and absence of interference resistance on the following connections:
3JK between components 120 and 244.
3C between components 120 and 244.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF001 / V42_V06_DF001
MR-453-X79-17B050$081.mif
V1
17B-17
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF002
PRESENT
OR
STORED
17B
Special notes:
The OBD and Level 1 warning lights illuminate.
NOTES
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the connection and condition of the connector of the air temperature sensor, component code 272 and of
the connections of the injection computer, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the air temperature sensor, component code 272 between connections 3B and 3JQ.
If the resistance measured is not between 300 X 6 k: replace the air temperature sensor, component
code 272.
Check the insulation, continuity and absence of interference resistance on the following connections:
3B between components 799 and 120.
3JQ between components 799 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF002 / V42_V06_DF002
MR-453-X79-17B050$081.mif
V1
17B-18
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF011
PRESENT
OR
STORED
17B
Special notes:
The OBD and Level 2 warning lights illuminate.
NOTES
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Disconnect the accelerator pedal sensor gang 1, component code 921 then switch on the ignition. Wait several
seconds so that the computer can update the fault status.
If the fault changes from present to stored: Replace the accelerator pedal sensor gang 1, component code 921
(see MR 388 or 451, Mechanical, 37A, Mechanical component controls, Accelerator pedal: Removal
Refitting).
Disconnect the motorised throttle valve, component code 1076 then switch on the ignition (see MR 388 or 451,
Mechanical, 12A, Fuel mixture, Throttle valve: Removal - Refitting).
Wait several seconds so that the computer can update the fault status.
If the fault changes from present to stored: Replace the damper valve position sensor, component code 1076
(see MR 388 or 451, Mechanical, 12A, Fuel mixture, Throttle valve: Removal - Refitting) referring to the
Replacement of components section.
Check the insulation, continuity and the absence of interference resistance on the following connections:
3LR between components 921 and 120,
3LT between components 921 and 120,
3MN between components 1076 and 120,
3MO between components 1076 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF011 / V42_V06_DF011
MR-453-X79-17B050$081.mif
V1
17B-19
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF012
PRESENT
OR
STORED
17B
Special notes:
The OBD and Level 2 warning lights illuminate.
NOTES
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Disconnect the accelerator pedal sensor gang 2, component code 921 then switch on the ignition (see MR 388
or 451, Mechanical, 37A, Mechanical component control, Accelerator pedal: Removal Refitting).
Wait several seconds so that the computer can update the fault status.
If the fault changes from present to stored: Replace the accelerator pedal sensor gang 2, component code 921
(see MR 388 or 451, Mechanical, 37A, Mechanical component controls, Accelerator pedal: Removal
Refitting).
Disconnect the manifold pressure sensor, component code 147, then switch on the ignition.
Wait several seconds so that the computer can update the fault status.
If the fault changes from present to stored: Replace the inlet pressure sensor, component code 147.
Disconnect the freon pressure sensor, component code 1202, then switch on the ignition (see MR 388 or 451,
Mechanical, 62A, Air conditioning, Pressure sensor: Removal - Refitting).
Wait several seconds so that the computer can update the fault status.
If the fault changes from present to stored: Replace the freon pressure sensor, component code 1202
(see MR 388 or 451, Mechanical, 62A, Air conditioning, Pressure sensor: Removal - Refitting).
Check the insulation, continuity and the absence of interference resistance on the following connections:
3LU between components 921 and 120,
3LV between components 921 and 120,
3AJP between components 147 and 120,
3AJR between components 147 and 120,
38Y between components 1202 and 120,
38U between components 1202 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF012 / V42_V06_DF012
MR-453-X79-17B050$081.mif
V1
17B-20
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF015
PRESENT
OR
STORED
NOTES
17B
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the connection and condition of the connectors of the passenger compartment fuse box, component code
1016, of the engine fuse box, component code 597, of the injection computer, component code 120 and of the
injection relay, component code 1047 (see MR 388 or 451, Mechanical, 87G, Engine compartment
connection unit, Engine compartment connection unit: List and location of components).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the condition and operation of the injection relay, component code 1047.
If the injection relay is faulty, replace the injection relay, component code 1047 (see MR 388 or 451, Mechanical,
87G, Engine compartment connection unit, Engine compartment connection unit: List and location of
components).
Check the insulation, continuity and the absence of interference resistance on the following connections:
3AA between components 1047 and 120,
3AC between components 1047 and 120,
AP29 between components 1016 and 120,
BP37 between components 597 and 1047,
BP17 between components 1047 and 597.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF015 / V42_V06_DF015
MR-453-X79-17B050$081.mif
V1
17B-21
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF018
PRESENT
OR
STORED
NOTES
17B
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Run command AC038 Low speed fan assembly relay and check the supply of the low speed fan assembly relay
control circuit using a test light on connection 3JN of component 120.
Check the connection and condition of the connector of the injection computer, component code 120 and of the
low speed fan assembly relay, component code 784.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and check for absence of interference resistance on the following
connection:
3JN between components 784 and 120.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Run command AC038 Low speed fan assembly relay and check the supply of the low speed fan assembly relay
power circuit using a test light on connection 49C of component 784.
If the check is not correct, replace the fan assembly control relay, component code 784.
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF018 / V42_V06_DF018
MR-453-X79-17B050$081.mif
V1
17B-22
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF026
PRESENT
OR
STORED
17B
The fault changes from stored to present when the engine is running at idle
speed.
NOTES
Special notes:
For CC.1 and CO, the OBD and Level 1 warning lights illuminate.
For CC.0, the Level 2 warning light illuminates.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the connection and condition of the connector of the injection computer, component code 120 and of the
cylinder 1 injector, component code 193.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the cylinder 1 injector, component code 193 between connections 3FB and 3CR.
If the resistance measured is not between 11 X 20 (K4M and D4D engine) or
9.2 X 17 (K7M engine): replace the cylinder 1 injector, component code 193 (see MR 388, Mechanical,
13A, Fuel supply, Injector rail - Injectors: Removal Refitting or MR 451, Mechanical, 17B, Petrol injection,
Injector rail - Injectors: Removal Refitting).
Run command AC005 Cylinder 1 injector and check the operation of the injector with a listening test.
Check the insulation, continuity and the absence of interference resistance on the following connections:
3CR between components 193 and 120.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the ignition on, check for + 12 V on connection 3FB of component 193.
If there is no + 12 V, check the continuity of the following connection:
3FB between components 597 and 193.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF026 / V42_V06_DF026
MR-453-X79-17B050$081.mif
V1
17B-23
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF027
PRESENT
OR
STORED
17B
The fault changes from stored to present when the engine is running at idle
speed.
NOTES
Special notes:
For CC.1 and CO, the OBD and Level 1 warning lights illuminate.
For CC.0, the Level 2 warning light illuminates.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the connection and condition of the connector of the injection computer, component code 120 and of the
cylinder 2 injector, component code 194.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the cylinder 2 injector, component code 194 between connections 3FB and 3CS.
If the resistance measured is not between 11 X 20 (K4M and D4D engine) or
9.2 X 17 (K7M engine): replace the cylinder 2 injector, component code 194 (see MR 388, Mechanical,
13A, Fuel supply, Injector rail - Injectors: Removal Refitting or MR 451, Mechanical, 17B, Petrol injection,
Injector rail - Injectors: Removal Refitting).
Run command AC006 Cylinder 2 injector and check the operation of the injector with a listening test.
Check the insulation, continuity and the absence of interference resistance on the following connections:
3CS between components 194 and 120.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the ignition on, check for + 12 V on connection 3FB of component 194.
If there is no + 12 V, check the continuity of the following connection:
3FB between components 1047 and 194.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF027 / V42_V06_DF027
MR-453-X79-17B050$081.mif
V1
17B-24
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF028
PRESENT
OR
STORED
17B
The fault changes from stored to present when the engine is running at idle
speed.
NOTES
Special notes:
For CC.1 and CO, the OBD and Level 1 warning lights illuminate.
For CC.0, the Level 2 warning light illuminates.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the connection and condition of the connector of the injection computer, component code 120 and of the
cylinder 3 injector, component code 195.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the cylinder 3 injector, component code 195 between connections 3FB and 3CT.
If the resistance measured is not between 11 X 20 (K4M and D4D engine) or
9.2 X 17 (K7M engine): replace the cylinder 3 injector, component code 195 (see MR 388, Mechanical,
13A, Fuel supply, Injector rail - Injectors: Removal Refitting or MR 451, Mechanical, 17B, Petrol injection,
Injector rail - Injectors: Removal Refitting).
Run command AC007 Cylinder 3 injector and check the operation of the injector with a listening test.
Check the insulation, continuity and the absence of interference resistance on the following connections:
3CT between components 195 and 120.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the ignition on, check for + 12 V on connection 3FB of component 195.
If there is no + 12 V, check the continuity of the following connection:
3FB between components 1047 and 195.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF028 / V42_V06_DF028
MR-453-X79-17B050$081.mif
V1
17B-25
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF029
PRESENT
OR
STORED
17B
The fault changes from stored to present when the engine is running at idle
speed.
NOTES
Special notes:
For CC.1 and CO, the OBD and Level 1 warning lights illuminate.
For CC.0, the Level 2 warning light illuminates.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the connection and condition of the connector of the injection computer, component code 120 and of the
cylinder 4 injector, component code 196.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the cylinder 4 injector, component code 196 between connections 3FB and 3CU.
If the resistance measured is not between 11 X 20 (K4M and D4D engine) or
9.2 X 17 (K7M engine): replace the cylinder 4 injector, component code 196 (see MR 388, Mechanical,
13A, Fuel supply, Injector rail - Injectors: Removal Refitting or MR 451, Mechanical, 17B, Petrol injection,
Injector rail - Injectors: Removal Refitting).
Run command AC008 Cylinder 4 injector and check the operation of the injector with a listening test.
Check the insulation, continuity and the absence of interference resistance on the following connections:
3CU between components 196 and 120.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the ignition on, check for + 12 V on connection 3FB of component 196.
If there is no + 12 V, check the continuity of the following connection:
3FB between components 1047 and 196.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF029 / V42_V06_DF029
MR-453-X79-17B050$081.mif
V1
17B-26
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF038
PRESENT
OR
STORED
17B
COMPUTER
1.DEF: Internal electronic fault.
Special notes:
The OBD and Level 2 warning lights illuminate.
NOTES
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
AFTER REPAIR
V42_V04_DF038 / V42_V06_DF038
MR-453-X79-17B050$081.mif
V1
17B-27
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF047
PRESENT
OR
STORED
17B
Special notes:
The OBD and Level 1 warning lights illuminate.
NOTES
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Move the wiring harness between the injection computer, component code 120 and the battery, component
code 107 to see if the status changes (Present Stored).
Look for any damage to the wiring harness and check the connection and condition of the battery, component
code 107 and its connections.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Start the engine and check the battery voltage using PR071 Computer supply voltage is X 9V.
Stop the engine and check the vehicle charging circuit (see MR 388 Mechanical, 16A, Starting Charging,
Charging circuit: Check).
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF047 / V42_V06_DF047
MR-453-X79-17B050$081.mif
V1
17B-28
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF050
PRESENT
OR
STORED
NOTES
17B
With the brake pedal released, check ET039 Brake pedal and ET799 Brake wire contact.
ET039 must be Released and ET799 Inactive.
Check the fitting and mechanical operation of the brake pedal (the pedal returns properly).
If the check is incorrect, check the braking system.
Remove the brake pedal switch, component code 160 (see MR 388 or 451, Mechanical, 37A, Mechanical
component controls, Brake pedal switch: Removal - Refitting) and, without action on the pedal, press
sufficiently on the brake pedal switch to seat it completely in its position.
Lock it by turning it an eighth of a turn.
With the brake pedal depressed, measure the resistance of the brake pedal switch, component code 160
between connections AP1 and 65A, the value must be X > 1000 k.
If the resistance is not correct, replace the brake pedal switch, component code 160 (see MR 388 or 451,
Mechanical, 37A, Mechanical component controls, Brake pedal switch: Removal - Refitting).
With the brake pedal released, measure the resistance of the brake pedal switch, component code 160 between
connections AP1 and 5A, the value must be between 0 < X 1 .
If the resistance is not correct, replace the brake pedal switch, component code 160 (see MR 388 or 451,
Mechanical, 37A, Mechanical component controls, Brake pedal switch: Removal - Refitting).
Check the brake pedal switch connector, component code 160 (see MR 388 or 451, Mechanical, 37A,
Mechanical component controls, Brake pedal switch: Removal - Refitting).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring
Check fuse F03 (10 A) and replace it if necessary.
Checking the brake pedal switch:
After the repair, perform these two checks.
With the brake pedal released, check ET039 and ET799.
ET039 must be Released and ET799 must be Inactive.
While depressing the brake pedal, check ET039 and ET799.
ET039 must be depressed and ET799 must be active.
The two checks must be correct.
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF050 / V42_V06_DF050
MR-453-X79-17B050$081.mif
V1
17B-29
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF059
PRESENT
OR
STORED
17B
1.DEF
NOTES
None.
Check the ignition coil circuit (see MR 388, Mechanical, 17A, Ignition, Ignition: Specifications),
Check the fuel supply circuit (see MR 388 or 451, Mechanical, 13A, Fuel supply, Fuel circuit: Operating
diagram),
Check the fuel supply pump circuit,
Check the condition of the cylinder 1 injector (see MR 388, Mechanical, 13A, Fuel supply, Injector rail Injectors: Removal Refitting or MR 451, Mechanical, 17B, Petrol injection, Injector rail - Injectors:
Removal Refitting),
Check the compression of cylinder 1.
After repair, check that the catalytic converter is not damaged by the misfire.
To do this, switch on the ignition, run the catalytic converter test SC006 Run OBD test: Catalytic converter
and start the engine (only depress the brake pedal to authorise the starting of the engine,
do not touch the accelerator pedal or clutch pedal).
At the end, check the test results:
STATUS1: Fault finding was not performed/impossible to obtain the necessary conditions
STATUS2: The component is in an average condition - sensor OK
STATUS3: The component is in a good condition - sensor OK
STATUS4: The component is in a poor condition - replace the catalytic converter (see MR 388 or 451, Mechanical,
19B, Exhaust, Catalytic converter: Removal - Refitting).
AFTER REPAIR
V42_V04_DF059 / V42_V06_DF059
MR-453-X79-17B050$081.mif
V1
17B-30
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
17B
DF059
CONTINUED
2.DEF
NOTES
None.
Check the ignition coil circuit (see MR 388, Mechanical, 17A, Ignition, Ignition: Specifications),
Check the fuel supply circuit (see MR 388 or 451, Mechanical, 13A, Fuel supply, Fuel circuit: Operating
diagram),
Check the fuel supply pump circuit
Check the condition of the cylinder 1 injector (see MR 388, Mechanical, 13A, Fuel supply, Injector rail Injectors: Removal Refitting or MR 451, Mechanical, 17B, Petrol injection, Injector rail - Injectors:
Removal Refitting),
Check the compression of cylinder 1.
AFTER REPAIR
MR-453-X79-17B050$081.mif
V1
17B-31
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF060
PRESENT
OR
STORED
17B
MISFIRING ON CYLINDER 2
1.DEF: Polluting misfiring
2.DEF: Destructive misfiring
1.DEF
NOTES
None.
Check the ignition coil circuit (see MR 388, Mechanical, 17A, Ignition, Ignition: Specifications),
Check the fuel supply circuit (see MR 388 or 451, Mechanical, 13A, Fuel supply, Fuel circuit: Operating
diagram),
Check the fuel supply pump circuit (see MR 388 or 451, Mechanical, 13A, Fuel supply, Fuel circuit:
Operating diagram),
Check the condition of the cylinder 2 injector (see MR 388, Mechanical, 13A, Fuel supply, Injector rail Injectors: Removal Refitting or MR 451, Mechanical, 17B, Petrol injection, Injector rail - Injectors:
Removal Refitting),
Check the compression of cylinder 2.
After repair, check that the catalytic converter is not damaged by the misfire.
To do this, switch on the ignition, run the catalytic converter test SC006 Run OBD test: Catalytic converter and
start the engine (only depress the brake pedal to authorise the starting of the engine,
do not touch the accelerator pedal or clutch pedal).
At the end, check the test results:
STATUS1: Fault finding was not performed/impossible to obtain the necessary conditions
STATUS2: The component is in an average condition - sensor OK
STATUS3: The component is in a good condition - sensor OK
STATUS4: The component is in a poor condition - replace the catalytic converter (see MR 388 or 451, Mechanical,
19B, Exhaust, Catalytic converter: Removal - Refitting).
AFTER REPAIR
V42_V04_DF060 / V42_V06_DF060
MR-453-X79-17B050$081.mif
V1
17B-32
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
17B
DF060
CONTINUED
2.DEF
NOTES
None.
Check the ignition coil circuit (see MR 388, Mechanical, 17A, Ignition, Ignition: Specifications),
Check the fuel supply circuit (see MR 388 or 451, Mechanical, 13A, Fuel supply, Fuel circuit:
Operating diagram),
Check the fuel supply pump circuit (see MR 388 or 451, Mechanical, 13A, Fuel supply, Fuel circuit:
Operating diagram),
Check the condition of the cylinder 2 injector (see MR 388, Mechanical, 13A, Fuel supply, Injector rail Injectors: Removal Refitting or MR 451, Mechanical, 17B, Petrol injection, Injector rail - Injectors:
Removal Refitting),
Check the compression of cylinder 2.
AFTER REPAIR
MR-453-X79-17B050$081.mif
V1
17B-33
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF061
PRESENT
OR
STORED
17B
MISFIRING ON CYLINDER 3
1.DEF: Polluting misfiring
2.DEF: Destructive misfiring
1.DEF
NOTES
None.
Check the ignition coil circuit (see MR 388, Mechanical, 17A, Ignition, Ignition: Specifications),
Check the fuel supply circuit (see MR 388 or 451, Mechanical, 13A, Fuel supply, Fuel circuit: Operating
diagram),
Check the fuel supply pump circuit (see MR 388, Mechanical, 13A, Fuel supply, Fuel circuit: Operating
diagram),
Check the condition of the cylinder 3 injector (see MR 388, Mechanical, 13A, Fuel supply, Injector rail Injectors: Removal Refitting or MR 451, Mechanical, 17B, Petrol injection, Injector rail - Injectors:
Removal Refitting),
Check the compression of cylinder 3.
After repair, check that the catalytic converter is not damaged by the misfire.
To do this, switch on the ignition, run the catalytic converter test SC006 Run OBD test: Catalytic converter
and start the engine (only depress the brake pedal to authorise the starting of the engine,
do not touch the accelerator pedal or clutch pedal).
At the end, check the test results:
STATUS1: Fault finding was not performed/impossible to obtain the necessary conditions
STATUS2: The component is in an average condition - sensor OK
STATUS3: The component is in a good condition - sensor OK
STATUS4: The component is in a poor condition - replace the catalytic converter (see MR 388 or 451, Mechanical,
19B, Exhaust, Catalytic converter: Removal - Refitting).
AFTER REPAIR
V42_V04_DF061 / V42_V06_DF061
MR-453-X79-17B050$081.mif
V1
17B-34
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
17B
DF061
CONTINUED
2.DEF
NOTES
None.
Check the ignition coil circuit (see MR 388, Mechanical, 17A, Ignition, Ignition: Specifications),
Check the fuel supply circuit (see MR 388 or 451, Mechanical, 13A, Fuel supply, Fuel circuit:
Operating diagram),
Check the fuel supply pump circuit (see MR 388 or 451, Mechanical, 13A, Fuel supply, Fuel circuit:
Operating diagram),
Check the condition of the cylinder 3 injector (see MR 388, Mechanical, 13A, Fuel supply, Injector rail Injectors: Removal Refitting or MR 451, Mechanical, 17B, Petrol injection, Injector rail - Injectors:
Removal Refitting),
Check the compression of cylinder 3.
AFTER REPAIR
MR-453-X79-17B050$081.mif
V1
17B-35
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF062
PRESENT
OR
STORED
17B
MISFIRING ON CYLINDER 4
1.DEF: Polluting misfiring
2.DEF: Destructive misfiring
1.DEF
NOTES
None.
Check the ignition coil circuit (see MR 388, Mechanical, 17A, Ignition, Ignition: Specifications),
Check the fuel supply circuit (see MR 388 or 451, Mechanical, 13A, Fuel supply, Fuel circuit:
Operating diagram),
Check the fuel supply pump circuit (see MR 388 or 451, Mechanical, 13A, Fuel supply, Fuel circuit:
Operating diagram),
Check the condition of the cylinder 4 injector (see MR 388, Mechanical, 13A, Fuel supply, Injector rail Injectors: Removal Refitting or MR 451, Mechanical, 17B, Petrol injection, Injector rail - Injectors:
Removal Refitting),
Check the compression of cylinder 4.
After repair, check that the catalytic converter is not damaged by the misfire.
To do this, switch on the ignition, run the catalytic converter test SC006 Run OBD test: Catalytic converter
and start the engine (only depress the brake pedal to authorise the starting of the engine,
do not touch the accelerator pedal or clutch pedal).
At the end, check the test results:
STATUS1: Fault finding was not performed/impossible to obtain the necessary conditions
STATUS2: The component is in an average condition - sensor OK
STATUS3: The component is in a good condition - sensor OK
STATUS4: The component is in a poor condition - replace the catalytic converter (see MR 388 or 451, Mechanical,
19B, Exhaust, Catalytic converter: Removal - Refitting).
AFTER REPAIR
V42_V04_DF062 / V42_V06_DF062
MR-453-X79-17B050$081.mif
V1
17B-36
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
17B
DF062
CONTINUED
2.DEF
NOTES
None.
Check the ignition coil circuit (see MR 388, Mechanical, 17A, Ignition, Ignition: Specifications),
Check the fuel supply circuit (see MR 388 or 451, Mechanical, 13A, Fuel supply, Fuel circuit:
Operating diagram),
Check the fuel supply pump circuit (see MR 388 or 451, Mechanical, 13A, Fuel supply, Fuel circuit:
Operating diagram),
Check the condition of the cylinder 4 injector (see MR 388, Mechanical, 13A, Fuel supply, Injector rail Injectors: Removal Refitting or MR 451, Mechanical, 17B, Petrol injection, Injector rail - Injectors:
Removal Refitting),
Check the compression of cylinder 4.
AFTER REPAIR
MR-453-X79-17B050$081.mif
V1
17B-37
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF065
PRESENT
OR
STORED
NOTES
17B
COMBUSTION MISFIRES
1.DEF: Polluting misfiring
2.DEF: Destructive misfiring
1.DEF
NOTES
None.
Check the ignition coil circuit (see MR 388, Mechanical, 17A, Ignition, Ignition: Specifications),
Check the fuel supply circuit (see MR 388 or 451, Mechanical, 13A, Fuel supply, Fuel circuit:
Operating diagram),
Check the fuel supply pump circuit (see MR 388 or 451, Mechanical, 13A, Fuel supply, Fuel circuit:
Operating diagram),
Check the condition of the cylinder injector (see MR 388, Mechanical, 13A, Fuel supply, Injector rail - Injectors:
Removal Refitting or MR 451, Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal
Refitting),
Check the compression of the cylinder.
After repair, check that the catalytic converter is not damaged by the misfire.
To do this, switch on the ignition, run the catalytic converter test SC006 Run OBD test: Catalytic converter
and start the engine (only depress the brake pedal to authorise the starting of the engine,
do not touch the accelerator pedal or clutch pedal).
At the end, check the test results:
STATUS1: Fault finding was not performed/impossible to obtain the necessary conditions
STATUS2: The component is in an average condition - sensor OK
STATUS3: The component is in a good condition - sensor OK
STATUS4: The component is in a poor condition - replace the catalytic converter (see MR 388 or 451, Mechanical,
19B, Exhaust, Catalytic converter: Removal - Refitting).
AFTER REPAIR
V42_V04_DF065 / V42_V06_DF065
MR-453-X79-17B050$081.mif
V1
17B-38
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
17B
DF065
CONTINUED
2.DEF
NOTES
None.
Check the ignition coil circuit (see MR 388, Mechanical, 17A, Ignition, Ignition: Specifications),
Check the fuel supply circuit (see MR 388 or 451, Mechanical, 13A, Fuel supply, Fuel circuit: Operating
diagram),
Check the fuel supply pump circuit (see MR 388 or 451, Mechanical, 13A, Fuel supply, Fuel circuit: Operating
diagram),
Check the condition of the cylinder injector (see MR 388, Mechanical, 13A, Fuel supply, Injector rail - Injectors:
Removal Refitting or MR 451, Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal
Refitting),
Check the compression of the cylinder.
AFTER REPAIR
MR-453-X79-17B050$081.mif
V1
17B-39
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF078
PRESENT
OR
STORED
17B
WARNING:
Never drive the vehicle without having confirmed that no faults involving the throttle valve are present.
NOTES
Check the cleanliness and condition of the injection computer connector, component code 120 and of the throttle
valve connector, component code 1076.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
3AJB between components 120 and 1076,
3AJC between components 120 and 1076.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline
AFTER REPAIR
V42_V04_DF078 / V42_V06_DF078
MR-453-X79-17B050$081.mif
V1
17B-40
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF079
PRESENT
OR
STORED
NOTES
17B
Check the cleanliness and condition of the injection computer connector, component code 120 and of the throttle
valve connector, component code 1076.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
If the fault is still present, manually check that the throttle valve rotates correctly.
Repair if necessary (see MR 388 or 451, Mechanical, 12A, Fuel mixture, Throttle valve: Cleaning).
Accelerate a couple of times and check that the values of PR538 Measured voltage gang 2 and PR539 Measured
voltage gang 1 vary according to acceleration.
If the fault is still present, disconnect the battery and the injection computer.
Check the insulation, continuity and absence of interference resistance of the following connections:
3AJB between components 120 and 1076,
3AJC between components 120 and 1076,
3MO between components 120 and 1076,
3MP between components 120 and 1076,
3MN between components 120 and 1076,
3MQbetween components 120 and 1076.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the throttle valve has been replaced, reinitialise the programming by running command RZ031 Throttle stop
programming.
If the fault is still present, contact Techline.
AFTER REPAIR
V42_V04_DF079 / V42_V06_DF079
MR-453-X79-17B050$081.mif
V1
17B-41
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF081
PRESENT
OR
STORED
17B
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
NOTES
Special notes:
For CO and CC.1, the OBD warning light and level 1 fault warning light illuminate.
Check the cleanliness and condition of the connector of the injection computer, component code 120 and of the
connector of the fuel vapour absorber bleed solenoid valve, component code 371.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
3FB between components 371 and 1047,
3BB between components 371 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the ignition on, check for + 12 V on connection 3FB of component 371.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the operation of the canister bleed solenoid valve using command AC017 Canister bleed solenoid valve.
Check the resistance of the fuel vapour absorber bleed solenoid valve.
If the resistance of the fuel vapour absorber bleed solenoid valve is not between: 24 < X < 30 between 0C
and 40C, replace the fuel vapour absorber bleed solenoid valve (see MR 388 or 451, Mechanical, 14A, Emission
control, Fuel vapour absorber: Removal - Refitting).
If the fault is still present, contact Techline.
AFTER REPAIR
V42_V04_DF081 / V42_V06_DF081
MR-453-X79-17B050$081.mif
V1
17B-42
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF082
PRESENT
OR
STORED
17B
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
NOTES
Special notes:
For CO and CC.1, the OBD warning light and level 1 fault warning light illuminate.
Check the condition of the fuse of the supply circuit for the upstream oxygen sensor, component code 887.
If the fuse is faulty, replace the fuse (see MR 388 or 451, Mechanical, 81C, Fuses, Fuses: List and location of
components).
Check the cleanliness and condition of the injection computer connector, component code 120 and of the
upstream oxygen sensor connector, component code 887.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
With the ignition on, check for + 12 V on connection 3FB of component 887.
Check the insulation, continuity and the absence of interference resistance of the following connection:
3FB between components 1047 and 887,
3GF between components 120 and 887.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
If all the checks are correct, replace the upstream oxygen sensor, component code 887 (see MR 388 or 452,
Mechanical, 17B, Petrol injection, Oxygen sensors: Removal - Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF082 / V42_V06_DF082
MR-453-X79-17B050$081.mif
V1
17B-43
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF083
PRESENT
OR
STORED
17B
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
NOTES
Special notes:
For CO and CC.1, the OBD warning light and level 1 fault warning light illuminate.
Check the condition of the fuse of the supply circuit for the downstream oxygen sensor, component code 242.
If the fuse is faulty, replace the fuse (see MR 388 or 451, Mechanical, 81C, Fuses, Fuses: List and location of
components).
Check the cleanliness and condition of the injection computer connector, component code 120 and of the
connector of the downstream oxygen sensor, component code 242.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
With the ignition on, check for + 12 V on connection 3FB of component 242.
Check the insulation, continuity and the absence of interference resistance of the following connection:
3FB between components 1047 and 242,
3GG between components 120 and 242.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
If all the checks are correct, replace the downstream oxygen sensor, component code 242 (see MR 388 or 451,
Mechanical, 17B, Petrol injection, Oxygen sensors: Removal - Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF083 / V42_V06_DF083
MR-453-X79-17B050$081.mif
V1
17B-44
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF085
PRESENT
OR
STORED
NOTES
17B
CO
CC.1
CC.0
NOTES
Special notes:
OBD warning light and level 2 fault warning light
illuminated.
NOTES
None.
Check the supply of the fuel supply pump relay control circuit with a test light by running command AC015 Fuel
pump relay.
Check the cleanliness and condition of the connector of the petrol pump relay, component code 236 (1047) and
of the injection computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connection:
3AC between components 236 (1047) and 120,
3NA between components 236 (1047) and 833.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the supply of the power circuit at the fuel supply pump relay output with a test light by running command
AC015 Fuel pump relay. If the supply at the relay output is not correct, replace the petrol pump relay, component
code 1047 (see MR 388 or 451, Mechanical, 87G, Engine compartment connection unit, Engine
compartment connection unit: List and location of components).
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF085 / V42_V06_DF085
MR-453-X79-17B050$081.mif
V1
17B-45
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF088
PRESENT
OR
STORED
17B
Special notes:
The Level 1 warning light is illuminated.
The wiring harness connecting the injection computer to the pinking sensor is
shielded, therefore a short circuit at + 12V is unlikely.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the cleanliness and condition of the pinking sensor, component code 146 and its connector.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the tightness of the pinking sensor (see MR 388 or 451, Mechanical, 17B, Petrol injection, Petrol
injection: List and location of components).
Check the cleanliness and condition of the injection computer connections, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector(s), otherwise, replace the wiring.
Check the internal resistance of the pinking sensor, component code 146. The resistance value of the sensor must
be: X > 10M . If the value is not correct, replace the pinking sensor, component code 146 (see MR 388,
Mechanical, 17B, Petrol injection, Petrol injection: List and location of components or MR 451, Mechanical,
17B, Petrol injection, Pinking sensor: Removal - Refitting).
Check the continuity and insulation of the following connections:
3S between components 120 and 146,
3DQ between components 120 and 146,
TB1 of component 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIR
V42_V04_DF088 / V42_V06_DF088
MR-453-X79-17B050$081.mif
V1
17B-46
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF091
PRESENT
OR
STORED
17B
2.DEF
Impossible to change the fault to present status; deal with the stored fault.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the cleanliness and condition of the connector of the vehicle speed sensor, component code 250 and of
the injection computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check for + after ignition feed using a multimeter on connection 3FB of the vehicle speed sensor, component
code 250.
Check the continuity and insulation of the following connections:
3FB between components 250 and 1047,
47F between components 120 and 250.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the correct operation of the injection relay, component code 1047 (see MR 388 or 451, Mechanical, 87G,
Engine compartment connection unit, Engine compartment connection unit: List and location of
components).
If the checks are correct and the fault is still present, replace the vehicle speed sensor, component code 250.
If the fault is still present, contact Techline.
AFTER REPAIR
V42_V04_DF091 / V42_V06_DF091
MR-453-X79-17B050$081.mif
V1
17B-47
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF092
PRESENT
OR
STORED
17B
NOTES
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
CO
CC.1
CC.0
NOTES
Special notes:
level 1 fault warning light illuminated.
Check the cleanliness and condition of the connector of the upstream oxygen sensor, component code 887 and
of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
3GH between components 120 and 887,
3GK between components 120 and 887.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF092 / V42_V06_DF092
MR-453-X79-17B050$082.mif
V1
17B-48
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
17B
DF092
CONTINUED
(---)
NOTES
Special notes:
Level 1 fault warning light illuminated.
Deal with the stored fault
Check the resistance of the upstream oxygen sensor. The value must be between 7 < X < 10 and the sensor
temperature must be X < 40C. If the value is not correct, replace the upstream oxygen sensor (see MR 388 or
451, Mechanical, 17B, Petrol injection, Oxygen sensors: Removal Refitting).
Check that the programming of the TDC* sensor is correct. (see Replacement of components section).
Run test SC007 Run OBD test: O2 sensor and start the engine (Only depress the brake pedal to authorise the
starting of the engine).
At the end, check the test results:
STATUS1: Run the test again with the engine coolant temperature X > 90C.
STATUS2 or STATUS3: Sensor OK.
STATUS4: Replace the upstream oxygen sensor (see MR 388 or 451, Mechanical, 17B, Petrol injection,
Oxygen sensors: Removal Refitting).
If the fault is still present, contact the Techline.
*TDC: Top Dead Centre
AFTER REPAIR
MR-453-X79-17B050$082.mif
V1
17B-49
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF093
PRESENT
OR
STORED
17B
NOTES
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
CC.1
CC.0
NOTES
Special notes:
Level 1 fault warning light illuminated.
Check the condition of the fuse of the supply circuit for the downstream oxygen sensor, component code 242.
If the fuse is faulty, check all the following steps and replace the fuse (see MR 388 or 451, Mechanical, 81C,
Fuses, Fuses: List and location of components).
Check the cleanliness and condition of the injection computer connector, component code 120 and of the
connector of the downstream oxygen sensor, component code 242.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
3GJ between components 120 and 242,
3GL between components 120 and 242.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the downstream oxygen sensor, component code 242 (see MR 388 or 451,
Mechanical, 17B, Petrol injection, Oxygen sensors: Removal Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF093 / V42_V06_DF093
MR-453-X79-17B050$082.mif
V1
17B-50
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
17B
DF093
CONTINUED
CO
NOTES
None.
Check the condition of the fuse of the supply circuit for the downstream oxygen sensor, component code 242.
If the fuse is faulty, check all the following steps and replace the fuse (see MR 388 or 451, Mechanical, 81C,
Fuses, Fuses: List and location of components).
Read the stored speed within the context of the fault using PR089 Vehicle speed.
If the value is 0, drive the vehicle to reach a speed of 6 mph (10 km/h) and check PR089 again.
If the value of this parameter is 0 whilst driving, apply the fault finding procedure for DF091 Vehicle speed signal,
abandoning the steps described below. If PR089 operates normally, follow the fault finding procedure for this fault.
Check the cleanliness and condition of the injection computer connector, component code 120 and of the
connector of the downstream oxygen sensor, component code 242.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
3GJ between components 120 and 242,
3GL between components 120 and 242.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
If the fault is still present, replace the downstream oxygen sensor, component code 242 (see MR 388 or 451,
Mechanical, 17B, Petrol injection, Oxygen sensors: Removal Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIR
MR-453-X79-17B050$082.mif
V1
17B-51
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF095
PRESENT
OR
STORED
17B
WARNING
Never drive the vehicle without having confirmed that no faults involving the throttle valve are present.
Special notes:
OBD warning light and level 1 fault warning light illuminate,
The throttle no longer operates.
NOTES
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the cleanliness of the throttle valve, component code 1076 and that the throttle rotates properly
(no resistance point)
Check the cleanliness and condition of the throttle valve connector.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the cleanliness and condition of the injection computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
3MO between components 120 and 1076,
3MP between components 120 and 1076,
3MN between components 120 and 1076.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the throttle valve has been replaced, reinitialise the programming by running command RZ031 Throttle stop
programming.
If the fault is still present, contact Techline.
AFTER REPAIR
V42_V04_DF095 / V42_V06_DF095
MR-453-X79-17B050$082.mif
V1
17B-52
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF096
PRESENT
OR
STORED
17B
WARNING
Never drive the vehicle without having confirmed that no faults involving the throttle valve are present.
NOTES
Special notes:
OBD warning light and level 1 fault warning light illuminate,
The throttle no longer operates
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the cleanliness of the throttle valve, component code 1076 and that the throttle rotates properly
(no resistance point).
Check the cleanliness and condition of the injection computer connector, component code 120 and of the throttle
valve connector, component code 1076.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
3MQ between components 120 and 1076,
3MN between components 120 and 1076,
3MO between components 120 and 1076.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the throttle valve has been replaced, reinitialise the programming by running command RZ031 Throttle stop
programming.
If the fault is still present, contact Techline.
AFTER REPAIR
V42_V04_DF096 / V42_V06_DF096
MR-453-X79-17B050$082.mif
V1
17B-53
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF101
PRESENT
OR
STORED
NOTES
None
AFTER REPAIR
V42_V04_DF101 / V42_V06_DF101
MR-453-X79-17B050$082.mif
V1
17B-54
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF102
PRESENT
OR
STORED
17B
Special notes:
OBD warning light illuminated.
NOTES
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the cleanliness and condition of the alternator connector, component code 103 and of the injection
computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connection.
2K between components 103 and 120.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF102 / V42_V06_DF102
MR-453-X79-17B050$082.mif
V1
17B-55
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF109
PRESENT
OR
STORED
17B
1.DEF
NOTES
None.
Check the presence and conformity of the fuel in the tank (see Test 19 Checking the conformity of the fuel).
Check the ignition coil circuit (see MR 388, Mechanical, 17A, Ignition, Ignition: Specifications),
Check the fuel supply circuit (see MR 388 or 451, Mechanical, 13A, Fuel supply, Fuel circuit:
Operating diagram),
Check the fuel supply pump circuit (see MR 388 or 451, Mechanical, 13A, Fuel supply, Fuel circuit:
Operating diagram),
Check the condition of the injectors (see MR 388, Mechanical, 13A, Fuel supply, Injector rail - Injectors:
Removal Refitting or MR 451, Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal
Refitting),
Check the cylinder compressions.
After repair, check that the catalytic converter is not damaged by the misfire.
To do this, switch on the ignition, run the catalytic converter test SC006 Run OBD test: Catalytic converter
and start the engine (only depress the brake pedal to authorise the starting of the engine,
do not touch the accelerator pedal or clutch pedal).
At the end, check the test results:
STATUS1: Fault finding was not performed/impossible to obtain the necessary conditions
STATUS2: The component is in an average condition - sensor OK
STATUS3: The component is in a good condition - sensor OK
STATUS4: The component is in a poor condition - replace the catalytic converter (see MR 388 or 451, Mechanical,
19B, Exhaust, Catalytic converter: Removal - Refitting).
AFTER REPAIR
V42_V04_DF109 / V42_V06_DF109
MR-453-X79-17B050$082.mif
V1
17B-56
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
17B
DF109
CONTINUED
2.DEF
NOTES
None.
Check the presence and conformity of the fuel in the tank (see Test 19 Checking the conformity of the fuel).
Check the ignition coil circuit (see MR 388, Mechanical, 17A, Ignition, Ignition: Specifications),
Check the fuel supply circuit (see MR 388 or 451, Mechanical, 13A, Fuel supply, Fuel circuit:
Operating diagram),
Check the fuel supply pump circuit (see MR 388 or 451, Mechanical, 13A, Fuel supply, Fuel circuit:
Operating diagram),
Check the condition of the injectors (see MR 388, Mechanical, 13A, Fuel supply, Injector rail - Injectors:
Removal Refitting or MR 451, Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal
Refitting),
Check the cylinder compressions.
AFTER REPAIR
MR-453-X79-17B050$082.mif
V1
17B-57
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF120
PRESENT
OR
STORED
17B
NOTES
Special note:
OBD warning light and level 1 fault warning light illuminated.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the connection and condition of the connector of the crankshaft position sensor, component code 149
and of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the crankshaft position sensor component code 149 between connections 3BL and
3BG on the injection computer connector, component code 120.
If the resistance of the crankshaft position sensor is not between 175 X 295 (between 0C and 40C),
replace the crankshaft position sensor (see MR 388 or 451, Mechanical, 17B, Petrol injection, Crankshaft
position sensor: Removal - Refitting).
Check the insulation and continuity of the following connections:
3BG between components 149 and 120,
3BL between components 149 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check that the 58 teeth of the flywheel target are not damaged or broken.
Check that the target is securely mounted on the flywheel (see MR 388 or 451, Mechanical, 10A, Engine and
cylinder block assembly, Flywheel: Removal - Refitting): check the tightening torque and that there is no
angular play or movement in relation to the target shaft
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF120 / V42_V06_DF120
MR-453-X79-17B050$082.mif
V1
17B-58
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF342
PRESENT
OR
STORED
17B
Test the OBD warning light using a test warning light when switching on the ignition.
If the test warning light illuminates for a few seconds, replace the faulty warning light (see MR 388 or 451,
Mechanical, 83A, Instrument panel, Instrument panel, Removal - Refitting).
Check the continuity, insulation, and the absence of interference resistance on the following connection:
137C between components 120 and 247.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF342 / V42_V06_DF342
MR-453-X79-17B050$082.mif
V1
17B-59
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF361
PRESENT
OR
STORED
17B
NOTES
Special note:
For CC.1 and CO, the OBD warning light and level 1 fault warning light illuminate,
For CC.0, the OBD warning light and level 2 fault warning light illuminate.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
The D4D and K7M engines are equipped with a quadruple ignition coil module.
The K4M engine is equipped with 4 "pencil" type coils.
AFTER REPAIR
V42_V04_DF361 / V42_V06_DF361
MR-453-X79-17B050$082.mif
V1
17B-60
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
17B
DF361
CONTINUED
K4M engine
Check the cleanliness and condition of the pencil coil no.1 connector, component code 1077, of the pencil coil no.4
connector, component code 1080 and of the injection computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
3CZ between components 120 and 1077,
3CV between components 1077 and 1080.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
With the ignition on, check the supply of the pencil ignition coils, component code 1077 and 1080 using a test light
on connection 3NA of the injection relay, component code 1047.
Check the insulation, continuity and the absence of interference resistance on the following connection:
3NA between components 1080 and 1047.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIR
MR-453-X79-17B050$082.mif
V1
17B-61
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF362
PRESENT
OR
STORED
17B
NOTES
Special note:
For CC.1 and CO, the OBD warning light and level 1 fault warning light illuminate.
For CC.0, the OBD warning light and level 2 fault warning light illuminate.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
The D4D and K7M engines are equipped with a quadruple ignition coil module.
The K4M engine is equipped with 4 "pencil" type coils.
AFTER REPAIR
V42_V04_DF362 / V42_V06_DF362
MR-453-X79-17B050$082.mif
V1
17B-62
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
17B
DF362
CONTINUED
K4M engine
Check the cleanliness and condition of the injection computer connector, component code 120, of the pencil coil
no.2 connector, component code 1078 and of the pencil coil no.3 connector, component code 1079.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
3CP between components 120 and 1078,
3CW between components 1078 and 1079.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
With the ignition on, check the supply of the ignition coils, component code 1078 and 1079 using a test light on
connection 3NA of the injection relay, component code 1047.
Check the insulation, continuity and the absence of interference resistance on the following connection:
3NA between components 1079 and 1047.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIR
MR-453-X79-17B050$082.mif
V1
17B-63
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF394
PRESENT
OR
STORED
NOTES
17B
Check the downstream oxygen sensor (see MR 388 or 451, Mechanical, 17B, Petrol injection, Oxygen
sensors: Removal - Refitting).
Check the programming of the TDC* sensor (see Section: Replacement of components)
Run the catalytic converter test SC006 Run OBD test: Catalytic converter and start the engine (only depress
the brake pedal to authorise the starting of the engine,
do not touch the accelerator pedal or clutch pedal).
At the end, check the test results:
STATUS1: Fault finding was not performed/impossible to obtain the necessary conditions
STATUS2: The component is in an average condition - sensor OK
STATUS3: The component is in a good condition - sensor OK
STATUS4: The component is in a poor condition - replace the catalytic converter (see MR 388 or 451, Mechanical,
19B, Exhaust, Catalytic converter: Removal - Refitting).
If the fault is still present, contact the Techline.
*TDC: Top Dead Centre
AFTER REPAIR
V42_V04_DF394 / V42_V06_DF394
MR-453-X79-17B050$082.mif
V1
17B-64
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF398
PRESENT
OR
STORED
17B
AFTER REPAIR
V42_V04_DF398 / V42_V06_DF398
MR-453-X79-17B050$082.mif
V1
17B-65
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
17B
DF398
CONTINUED
AFTER REPAIR
MR-453-X79-17B050$082.mif
V1
17B-66
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF409
PRESENT
OR
STORED
17B
Special notes:
OBD warning light illuminated.
NOTES
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the cleanliness and condition of the injection computer connector, component code 120 and of the
instrument panel connector, component code 247.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
47H between components 120 and 247,
3NX between components 120 and 247,
137C between components 120 and 247,
31A between components 120 and 247.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF409 / V42_V06_DF409
MR-453-X79-17B050$082.mif
V1
17B-67
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF457
PRESENT
OR
STORED
17B
FLYWHEEL TARGET
1.DEF: Component in bad condition
NOTES
Special notes:
OBD warning light illuminated.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the cleanliness and condition of the injection computer connector, component code 120 and of the TDC*
sensor connector, component code 149.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the TDC* sensor component code 149 between connections 3BL and 3BG on the
injection computer connector, component code 120.
If the resistance of the crankshaft position sensor is not between 175 X 295 (between 0C and 40C),
replace the crankshaft position sensor (see MR 388 or 451, Mechanical, 17B, Petrol injection, Crankshaft
position sensor: Removal - Refitting).
Check the insulation, continuity and the absence of interference resistance on the following connections:
3BG between components 120 and 149,
3BL between components 120 and 149.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the cleanliness and condition of the flywheel (see MR 388 or 451, Mechanical, 10A, Engine and cylinder
block assembly, Flywheel: Removal - Refitting).
If the fault is still present, contact the Techline.
*TDC: Top Dead Centre
AFTER REPAIR
V42_V04_DF457 / V42_V06_DF457
MR-453-X79-17B050$082.mif
V1
17B-68
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF532
PRESENT
OR
STORED
17B
NOTES
Special notes:
The OBD warning light is lit.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the cleanliness and condition of the alternator connector, component code 103 and of the injection
computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connection.
2K between components 103 and 120.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connection is correct, replace the alternator, component code 103 (see MR 388 or 451, Mechanical, 16A,
Starting - Charging, Alternator: Removal - Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF532 / V42_V06_DF532
MR-453-X79-17B050$082.mif
V1
17B-69
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF556
PRESENT
OR
STORED
17B
NOTES
Special notes:
For 1.DEF, the OBD and level 1 fault warning lights are illuminated.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the cleanliness and condition of the injection computer connector, component code 120 and of the damper
valve connector, component code 1076 (see MR 388 or 451, Mechanical, 17B, Petrol injection, Petrol injection
computer: Removal - Refitting).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
3AJB between components 1076 and 120,
3AJC between components 1076 and 120.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF556 / V42_V06_DF556
MR-453-X79-17B050$082.mif
V1
17B-70
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF631
PRESENT
OR
STORED
NOTES
17B
With the brake pedal released, check ET039 Brake pedal and ET799 Brake wire contact.
Check that ET039 is Released and ET799 is Inactive.
Check the fitting and mechanical operation of the brake pedal (the pedal returns properly).
If the check is incorrect, check the braking system.
Remove the brake pedal switch, component code 160 (see MR 388 or 451, Mechanical, 37A, Mechanical
component controls, Brake pedal switch: Removal - Refitting) and, without action on the pedal, press
sufficiently on the brake pedal switch to seat it completely in its position.
Lock it by turning it a quarter of a turn anti-clockwise.
The fault should change from present to stored.
While depressing the brake pedal to the end of travel, check ET039 and ET799.
ET039 must be depressed and ET799 must be active.
If the statuses are correct, contact the Techline.
With the brake pedal depressed, measure the resistance of the brake pedal switch, component code 160
between connections AP1 and 65A, the value must be X > 10 M.
If the resistance is not correct, replace the brake pedal switch, component code 160 (see MR 388 or 451,
Mechanical, 37A, Mechanical component controls, Brake pedal switch: Removal - Refitting).
- With the brake pedal released, measure the resistance of the brake pedal switch, component code 160 between
connections AP1 and 5A, the value must be between 0 < X 1 .
If the resistance is not correct, replace the brake pedal switch, component code 160 (see MR 388, Mechanical,
37A, Mechanical component controls, Brake pedal switch: Removal - Refitting).
Check the brake pedal switch connector, component code 160 (see MR 388 or 451, Mechanical, 37A,
Mechanical component controls, Brake pedal switch: Removal - Refitting).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring
Check fuse F03 (10 A) and replace it if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connections:
AP1 between components 160 and 1016,
5A between components 160 and 120,
65A between components 160 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF631 / V42_V06_DF631
MR-453-X79-17B050$082.mif
V1
17B-71
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF648
PRESENT
OR
STORED
NOTES
17B
COMPUTER
Special notes:
The OBD and Level 2 fault warning lights are illuminated.
AFTER REPAIR
V42_V04_DF648 / V42_V06_DF648
MR-453-X79-17B050$082.mif
V1
17B-72
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF721
PRESENT
OR
STORED
17B
ENGINE OVERHEATING
1.DEF: Operating temperature too high.
NOTES
Special notes:
After this fault appears:
The level 1 warning light is illuminated.
The overheating warning light is illuminated.
Check the engine cooling system (see MR 388 or 451, Mechanical, 19A, Cooling, Engine cooling system:
Check).
Check the coolant temperature sensor by applying TEST 15 Checking the coolant temperature sensor.
Check the correct operation of the engine cooling fans (see Test 16 Checking the fan relay).
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF721 / V42_V06_DF721
MR-453-X79-17B050$082.mif
V1
17B-73
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF884
PRESENT
OR
STORED
17B
Check the supply of the control circuit of the additional fuel supply pump relay with a test light by running command
AC224 Additional petrol circuit pump relay.
Check the cleanliness and condition of the connector of the additional petrol pump relay, component code 1639
and of the injection computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connection:
3ACK between components 1639 and 120,
3FB between components 1639 and 1047.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
Check the supply of the power circuit of the additional fuel supply pump relay with a test light by running command
AC224 Additional petrol circuit pump relay. If the check is correct, replace the pump, component code 1639
(see MR 388, Mechanical, 19C, Tank, Additional fuel system petrol pump: Removal - Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF884 / V42_V06_DF884
MR-453-X79-17B050$082.mif
V1
17B-74
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF887
PRESENT
OR
STORED
17B
1.DEF
2.DEF
NOTES
None.
Check that the accelerator pedal is not jammed and that there is nothing impeding its operation (floor carpet, etc.).
Run TEST 9 Brake pedal switch check.
Run TEST 8 Accelerator pedal potentiometer check.
If the fault is still present, contact the Techline.
NOTES
3.DEF
None.
If fault 3.DEF: Inconsistency between pedal gang 1 and gang 2 is the only fault and is present, replace the
accelerator pedal (see MR 388 or 451, Mechanical, 37A, Mechanical component control, Accelerator pedal:
Removal Refitting).
If the fault is still present, contact the Techline.
NOTES
4.DEF
None.
AFTER REPAIR
V42_V04_DF887 / V42_V06_DF887
MR-453-X79-17B050$082.mif
V1
17B-75
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF894
PRESENT
OR
STORED
NOTES
17B
Check the connection and condition of the connector of the additional fuel circuit solenoid valve, component code
1640 and the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity, insulation, and absence of interference resistance on the following connections:
3ACM between components 1640 and 120,
3FB between components 1640 and 1047.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
Check the supply of the solenoid valve using a test light, by running command AC217 Additional fuel circuit
solenoid valve.
Check the internal resistance of the solenoid valve, component code 1640 on the computer connector, its value
must be between: 24 < X 30. If the resistance is incorrect, replace the solenoid valve.
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF894/ V42_V06_DF894
MR-453-X79-17B050$082.mif
V1
17B-76
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF974
PRESENT
OR
STORED
17B
Fault priorities:
Deal with the following fault as a priority:
DF011 Sensor voltage supply no. 1
NOTES
Special notes:
After this fault appears:
The OBD and level 1 warning lights are illuminated.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the connection and condition of the connector of the accelerator pedal sensor, gang 1, component
code 921 and of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Run TEST 8 Accelerator pedal potentiometer check.
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF974 / V42_V06_DF974
MR-453-X79-17B050$082.mif
V1
17B-77
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF975
PRESENT
OR
STORED
17B
Special notes:
After this fault appears:
The OBD and level 1 warning lights are illuminated.
NOTES
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the connection and condition of the connector of the accelerator pedal sensor, gang 2, component
code 921 and of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Run TEST 8 Accelerator pedal potentiometer check.
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF975 / V42_V06_DF975
MR-453-X79-17B050$082.mif
V1
17B-78
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF992
PRESENT
OR
STORED
NOTES
17B
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the cleanliness and condition of the additional heater 1 relay, component code 1067 and the connections
of the injection computer, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connection:
38JU between components 1067 and 120,
3FB between components 1067 and 1047.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check that the additional heater relay operates correctly by running command AC250 Heating resistor 1 relay
and check that there are no more faults on the relay. If the check is not correct, replace the additional heater relay,
component code 1067 (see MR 388 or 451, Mechanical, 61A, Heating system, Heating resistor relay:
Removal - Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF992 / V42_V06_DF992
MR-453-X79-17B050$082.mif
V1
17B-79
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF993
PRESENT
OR
STORED
NOTES
17B
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the cleanliness and condition of the additional heater 2 relay, component code 1068 and the connections
of the injection computer, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connection:
38JV between components 1068 and 120,
3FB between components 1068 and 1047.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check that the additional heater relay operates correctly by running command AC251 Heating resistor 2 relay
and check that there are no more faults on the relay. If the check is not correct, replace the additional heater relay,
component code 1068 (see MR 388 or 451, Mechanical, 61A, Heating system, Heating resistor relay:
Removal - Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF993 / V42_V06_DF993
MR-453-X79-17B050$082.mif
V1
17B-80
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF994
PRESENT
OR
STORED
NOTES
17B
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the cleanliness and condition of the additional heater 3 relay, component code 1069 and the connections
of the injection computer, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connection:
38JW between components 1069 and 120,
3FB between components 1069 and 1047.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check that the additional heater relay operates correctly by running command AC252 Heating resistor 3 relay
and check that there are no more faults on the relay. If the check is not correct, replace the additional heater relay,
component code 1069 (see MR 388 or 451, Mechanical, 61A, Heating system, Heating resistor relay:
Removal - Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF994 / V42_V06_DF994
MR-453-X79-17B050$082.mif
V1
17B-81
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF1015
PRESENT
OR
STORED
17B
Fault priorities
Deal with the following faults first:
DF050 Brake switch circuit
DF631 Brake light switch signal
NOTES
With the brake pedal released, check ET039 Brake pedal and ET799 Brake wire contact.
If ET039 is Released and ET799 is Inactive.
Check the fitting and mechanical operation of the brake pedal (the pedal returns properly).
If the check is incorrect, check the braking system.
Remove the brake pedal switch, component code 160 (see MR 388 or 451, Mechanical, 37A, Mechanical
component controls, Brake pedal switch: Removal - Refitting) and, without action on the pedal, press
sufficiently on the brake pedal switch to seat it completely in its position.
Lock it by turning it an eighth of a turn.
The fault should change from present to stored.
With the brake pedal depressed, measure the resistance of the brake pedal switch, component code 160
between connections AP1 and 65A, the value must be X > 10 M.
If the resistance is not correct, replace the brake pedal switch, component code 160 (see MR 388 or 451,
Mechanical, 37A, Mechanical component controls, Brake pedal switch: Removal - Refitting).
With the brake pedal released, measure the resistance of the brake pedal switch, component code 160
between connections AP1 and 5A, the value must be between 0 < X 1 .
If the resistance is not correct, replace the brake pedal switch, component code 160 (see MR 388 or 451,
Mechanical, 37A, Mechanical component controls, Brake pedal switch: Removal - Refitting).
Check the brake pedal switch connector, component code 160 (see MR 388 or 451, Mechanical, 37A,
Mechanical component controls, Brake pedal switch: Removal - Refitting).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check fuse F03 (10 A) and replace it if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF1015 / V42_V06_DF1015
MR-453-X79-17B050$082.mif
V1
17B-82
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF1017
PRESENT
OR
STORED
NOTES
17B
COMPUTER
1.DEF: Internal electronic fault.
2.DEF: Internal electronic fault.
NOTES
1.DEF
None.
2.DEF
NOTES
None.
AFTER REPAIR
V42_V04_DF1017 / V42_V06_DF1017
MR-453-X79-17B050$082.mif
V1
17B-83
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF1058
PRESENT
OR
STORED
17B
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the fitting and sealing of the inlet air pressure sensor, component code 147 (condition of the seals) and look
for possible leaks on the inlet air pipe.
Check the connector of the inlet air pressure sensor, component code 147.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the supply voltage of the sensor on connections 3AJR and 3AJP.
Check the insulation, continuity and the absence of interference resistance on the following connections:
3AJP between components 120 and 147,
3AJR between components 120 and 147,
3AJQ between components 120 and 147.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Replace the inlet air pressure sensor, component code 147 and check that the fault is no longer present
(see MR 388 or 451, Mechanical, 12A, Fuel mixture, Air inlet: Description).
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF1058 / V42_V06_DF1058
MR-453-X79-17B050$082.mif
V1
17B-84
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF1063
PRESENT
OR
STORED
NOTES
17B
None.
AFTER REPAIR
V42_V04_DF1063 / V42_V06_DF1063
MR-453-X79-17B050$082.mif
V1
17B-85
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF1068
PRESENT
OR
STORED
NOTES
17B
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the connection and condition of the refrigerant pressure sensor connector, component code 1202 and of
the injection computer connector, component code 120.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
With the ignition on, check for the presence of + 5 V on connection 38Y and an earth on connection 38U of the
refrigerant fluid pressure sensor.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation, continuity and the absence of interference resistance on the following connections:
38Y between components 1202 and 120,
38X between components 1202 and 120,
38U between components 1202 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the refrigerant pressure sensor, component code 1202 (see MR 388 or 451,
Mechanical, 62A, Air conditioning, Pressure sensor: Removal Refitting, MR 388 or 451, Mechanical, 62A,
Air conditioning: Precautions for repair, MR 388 or 451, Mechanical, 62A, Air conditioning: Parts and
consumables for the repair).
If the fault is still present, contact the Techline.
REFRIGER.*: REFRIGERANT.
AFTER REPAIR
V42_V04_DF1068 / V42_V06_DF1068
MR-453-X79-17B050$082.mif
V1
17B-86
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF1072
PRESENT
OR
STORED
NOTES
17B
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the connection and condition of the air conditioning compressor control relay connector, component
code 474 and the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
38K between components 474 and 120,
3FB between components 1047 and 474.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Run command AC180 Air conditioning compressor relay control in order to check that the relay operates
correctly.
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF1072 / V42_V06_DF1072
MR-453-X79-17B050$082.mif
V1
17B-87
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF1074
PRESENT
OR
STORED
17B
NOTES
Special note:
For 1.DEF, the OBD warning light illuminates,
For 2.DEF, the OBD warning light and level 2 fault warning light illuminate.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the connection and condition of the motorised throttle valve connector, component code 1076 and the
injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
3AJB between components 1076 and 120,
3AJC between components 1076 and 120,
3MP between components 1076 and 120,
3MQ between components 1076 and 120,
3MO between components 1076 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIR
V42_V04_DF1074 / V42_V06_DF1074
MR-453-X79-17B050$082.mif
V1
17B-88
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of faults
DF1355
PRESENT
OR
STORED
NOTES
17B
None.
AFTER REPAIR
V42_V04_DF1355 / V42_V06_DF1355
MR-453-X79-17B050$082.mif
V1
17B-89
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Conformity check
17B
The global conformity check for the functions and sub-functions of this system is no longer interpreted in the
conformity check. Instead, all information available in the functions and sub-functions can be found in the following
chapters:
For STATUSES, refer to INTERPRETATION OF STATUSES.
For PARAMETERS, refer to INTERPRETATION OF PARAMETERS.
For COMMANDS, refer to INTERPRETATION OF COMMANDS.
V42_V04_CCONF / V42_V06_CCONF
MR-453-X79-17B050$090.mif
V1
17B-90
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Status summary table
Tool status
ET001
ET038
Engine
ET039
Brake pedal
ET041
Gearbox ratio
ET047
ET051
ET089
ET148
ET321
ET405
ET434
ET673
ET717
ET734
ET735
ET736
ET759
ET760
First starting
ET775
ET798
ET799
ET813
ET814
ET819
ET820
ET836
ET837
Crankshaft synchronisation
ET831
Injection protection
V42_V04_CCONF / V42_V06_CCONF
MR-453-X79-17B050$100.mif
V1
17B-91
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of statuses
17B
STATUS DEFINITION
PRESENT: This status indicates that the + after ignition feed is active.
ABSENT: This status indicates that the + after ignition is not active.
NOTES
"PRESENT"
None.
With the ignition on and engine running warm at idle speed, + after ignition feed is activated.
In the event of a fault, apply the interpretation of DF047 Computer supply voltage.
AFTER REPAIR
V42_V04_ET001 / V42_V06_ET001
MR-453-X79-17B050$110.mif
V1
17B-92
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of statuses
17B
ENGINE
ET038
STATUS DEFINITION
AFTER REPAIR
STOPPED: This status indicates that the engine ignition is on without the
starter engaged.
STALLED: This status indicates that the engine has stalled.
RUNNING: This status indicates that the engine has started.
STARTING: This status indicates that the engine is in starting phase.
Deal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V42_V04_ET038 / V42_V06_ET038
MR-453-X79-17B050$110.mif
V1
17B-93
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of statuses
17B
GEAR
ET041
STATUS DEFINITION
AFTER REPAIR
Deal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V42_V04_ET041 / V42_V06_ET041
MR-453-X79-17B050$110.mif
V1
17B-94
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of statuses
17B
ACTIVE
Status ET047 is INACTIVE when the engine is stopped and the ignition off.
INACTIVE
AFTER REPAIR
Deal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V42_V04_ET047 / V42_V06_ET047
MR-453-X79-17B050$110.mif
V1
17B-95
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of statuses
17B
STATUS DEFINITION
COMPLETED: This status indicates that the throttle stops have been programmed
NOT COMPLETED: This status indicates that the throttle stops have not been
programmed.
COMPLETED
Even though this programming is automatic, take particular care when performing the
first motorised throttle stop programming operation.
This can be carried out on several occasions:
when a computer is switched on for the first time,
at the end of computer programming (see Replacement of components)
The air temperature must be above 0C during programming, then, at the end of
programming, switch off the ignition and wait 30 seconds for the end of Power Latch
so that the computer can store the programmed stops.
This means that the throttle stops have not been programmed.
NOT
COMPLETED
AFTER REPAIR
Deal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V42_V04_ET051 / V42_V06_ET051
MR-453-X79-17B050$110.mif
V1
17B-96
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of statuses
17B
STATUS DEFINITION
COMPLETED: This status indicates that the throttle stops have been programmed
NOT COMPLETED: This status indicates that the throttle stops have not been
programmed.
COMPLETED
In the event of a fault, program the engine flywheel target (see Replacement of
components).
In the event of a fault, apply the interpretation of DF457 Flywheel target.
This means that the engine flywheel target programming has not been completed.
NOT
COMPLETED
AFTER REPAIR
Deal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V42_V04_ET089 / V42_V06_ET089
MR-453-X79-17B050$110.mif
V1
17B-97
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of statuses
17B
STATUS DEFINITION
NOTES
YES: This status indicates that the warning light is lit continuously.
NO: This status indicates that the warning light is off.
FLASHING: This status indicates that the warning light flashes.
SELF TEST: This status indicates that the warning light is performing a self test.
Special notes:
In the event of normal operation, this warning light must remain off (NO).
"YES"
AFTER REPAIR
Deal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V42_V04_ET148 / V42_V06_ET148
MR-453-X79-17B050$110.mif
V1
17B-98
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of statuses
17B
ACTIVE: This status indicates that the air conditioning compressor is active.
STATUS DEFINITION
INACTIVE: This status indicates that the air conditioning compressor is inactive
NOTES
Special notes:
Only perform these tests if the status does not correspond with the system programming
functions.
ACTIVE
AFTER REPAIR
Deal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V42_V04_ET321 / V42_V06_ET321
MR-453-X79-17B050$110.mif
V1
17B-99
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of statuses
17B
NOTES
Special notes:
Apply the checks only if statuses ACTIVE and INACTIVE are inconsistent
with the pedal position.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80C.
Check the condition and fitting of the clutch pedal position sensor, component
code 675 (see MR 388, Mechanical, 37A, Mechanical component controls,
Clutch pedal position sensor: Removal Refitting or MR 451, Mechanical, 37A,
Mechanical component controls, Clutch pedal: Removal - Refitting).
Remove the clutch pedal position sensor, component code 675 (see MR
388, Mechanical, 37A, Mechanical component controls, Clutch pedal position
sensor: Removal Refitting or MR 451, Mechanical, 37A, Mechanical
component controls, Clutch pedal: Removal - Refitting).
Check the insulation between connections MAM and 86D of component 675 with the
switch in the rest position.
Repeat this operation with the switch pressed, and check the continuity and the
absence of interference resistance between the two connections.
If these 2 checks are not correct, replace the clutch pedal position sensor,
component code 675 (see MR 388, Mechanical, 37A, Mechanical component
controls, Clutch pedal position sensor: Removal Refitting or MR 451,
Mechanical, 37A, Mechanical component controls, Clutch pedal: Removal Refitting).
Then check the continuity and absence of interference resistance of the following
connection:
86D between components 120 and 675.
Check that the earth is in order on connection MAM of component 675.
If the connection or connections are faulty and if there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
INACTIVE
AFTER REPAIR
Deal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V42_V04_ET405 / V42_V06_ET405
MR-453-X79-17B050$110.mif
V1
17B-100
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of statuses
17B
ET405
CONTINUED
ACTIVE
AFTER REPAIR
MR-453-X79-17B050$110.mif
V1
Check the condition and fitting of the clutch pedal position sensor.
Remove the clutch pedal position sensor, component code 675 (see MR 388,
Mechanical, 37A, Mechanical component controls, Clutch pedal position
sensor: Removal Refitting or MR 451, Mechanical, 37A, Mechanical
component controls, Clutch pedal: Removal - Refitting), check the insulation
between connections MAM and 86D of component 675, with the switch in the
rest position.
Repeat this operation with the switch pressed, and check the continuity and
the absence of interference resistance between the two connections.
If these 2 checks are not correct, replace the clutch pedal position sensor,
component code 675 (see MR 388 or 451, Mechanical, 37A,
Mechanical component controls, Clutch pedal position sensor: Removal
Refitting or MR 451, Mechanical, 37A, Mechanical component controls, Clutch
pedal: Removal - Refitting).
Deal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
17B-101
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of statuses
17B
STATUS DEFINITION
NOTES
To reinitialise this status, clear the fault memory by running command RZ001 Fault
memory.
YES
AFTER REPAIR
Deal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V42_V04_ET673 / V42_V06_ET673
MR-453-X79-17B050$110.mif
V1
17B-102
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of statuses
17B
STATUS DEFINITION
AFTER REPAIR
Deal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V42_V04_ET717 / V42_V06_ET717
MR-453-X79-17B050$110.mif
V1
17B-103
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of statuses
17B
ET734
ET735
ET736
STATUS DEFINITION
INACTIVE
ACTIVE
Statuses ET734, ET735 and ET736 are INACTIVE with the ignition on and the engine
stopped, or when the engine is warm.
Statuses ET734, ET735 and ET736 are ACTIVE when the engine is started, the
engine coolant temperature is low (< 15C) and the air temperature is low (< 5).
This program allows the engine coolant to be heated to enable the passenger
compartment to be heated.
To control the operation of the relays, run the following commands:
AC250 Heating resistor no.1 relay.
AC251 Heating resistor no.2 relay.
AC252 Heating resistor no.3 relay.
In the event of a fault, refer to the interpretation of faults:
DF992 Additional heater relay 1 circuit.
DF993 Additional heater relay 2 circuit.
DF994 Additional heater relay 3 circuit.
AFTER REPAIR
Deal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
17B-104
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of statuses
17B
STATUS DEFINITION
ABSENT: This status indicates that the braking multiplex signal detected is absent.
PRESENT: This status indicates that the braking multiplex signal detected is present.
INTERMEDIATE: This status indicates that the braking multiplex signal detected is
intermediate.
PRESENT INTERMEDIATE
"ABSENT"
AFTER REPAIR
Check the correct position and the conformity of the brake pedal sensor.
Run fault finding on the UCH domain (see 87B, UCH).
Deal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V42_V04_ET759 / V42_V06_ET759
MR-453-X79-17B050$110.mif
V1
17B-105
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of statuses
17B
STATUS DEFINITION
DETECTED: This status indicates that the TDC sensor signal is detected.
NOT DETECTED: This status indicates that the TDC sensor signal is not detected.
NOT DETECTED
AFTER REPAIR
In the event of a fault, refer to the interpretation of fault DF120 Engine speed sensor
signal.
Deal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V42_V04_ET836 / V42_V06_ET836
MR-453-X79-17B050$110.mif
V1
17B-106
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of statuses
17B
INJECTION PROTECTION
ET846
STATUS DEFINITION
NOT PROTECTED
BLANK: No signal
PROTECTED STATUS 1: Fault on coded line circuit
PROTECTED STATUS 2: Fault on immobiliser memory area
PROTECTED STATUS 3: Injection computer self-protection
BLANK:
The injection computer does not receive a signal from the UCH computer.
Run fault finding on the multiplex network.
PROTECTED STATUS 1:
The UCH computer does not respond to the authentication requests from the injection computer.
Several possibilities:
either the UCH computer was not programmed with the vehicle's card/key,
or the vehicle's card/key is not recognised by the UCH computer.
Run fault finding on the UCH computer.
PROTECTED STATUS 2:
Several possibilities:
either the injection computer is blank and was not programmed with the immobiliser code, and the UCH
computer is not authorised to send the immobiliser code,
Connect a diagnostic tool to the UCH computer to authorise it to send the immobiliser code.
or the UCH computer has detected a fault,
Run fault finding on the UCH computer.
AFTER REPAIR
Deal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V42_V04_ET846 / V42_V06_ET846
MR-453-X79-17B050$110.mif
V1
17B-107
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of statuses
17B
ET846
CONTINUED
PROTECTED STATUS 3:
There are several possible causes, in the following order:
check that the UCH computer has not detected a fault,
Run fault finding on the UCH computer.
check that the injection computer has not already been programmed with the immobiliser code for another
vehicle using the status.
Check that the injection computer corresponds correctly to the vehicle on which fault finding is being run.
if none of the 2 previous points is the cause, check that the injection computer is not in anti-scanning mode
after undergoing several failed authentication attempts,
It only leaves this mode when the following sequence of operations is carried out:
1- switch off the ignition,
2- switch on the ignition again and wait for at least 20 seconds under + after ignition feed,
3- switch off the ignition and ensure that the end of the self-feed phase of the injection computer is observed
(the length of time varies depending on the engine coolant temperature and can be 10 minutes maximum),
4- switch on the ignition again and start the vehicle,
5- if the vehicle does not start, repeat this procedure 3 times,
6- if the vehicle still does not start, contact the Techline.
AFTER REPAIR
MR-453-X79-17B050$110.mif
V1
Deal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
17B-108
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Parameter summary table
Tool
Parameter
PR002
Alternator charge
PR015
Engine torque
PR030
PR037
Refrigerant pressure
PR041
Turbocharging pressure
PR055
Engine speed
PR059
PR064
Coolant temperature
PR071
PR084
PR089
Vehicle speed
PR097
PR098
PR099
PR102
PR118
PR119
PR138
Richness correction
PR139
PR147
PR148
PR215
PR216
PR312
PR313
PR344
PR427
PR429
PR444
MR-453-X79-17B050$120.mif
V1
17B-109
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Parameter summary table
Tool
Parameter
PR446
PR447
PR448
Ignition advance
PR469
PR471
PR473
PR475
PR492
PR538
PR539
PR606
PR624
PR625
PR770
Camshaft offset
PR814
PR831
PR832
PR833
PR834
PR847
PR872
PR877
PR887
PR931
PR1026
PR1029
Alternator power
PR1129
PR1153
Refriger.*: refrigerant
Synchro*: Synchronisation
MR-453-X79-17B050$120.mif
V1
17B-110
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
ENGINE TORQUE
PR015
PARAMETER
DEFINITION
Conformity check with the engine running and engine coolant temperature > 80C
The value must be between 20 Nm < PR015 < 40 Nm
This parameter is only valid when the engine is running.
AFTER REPAIR
V42_V04_PR015 / V42_V06_PR015
MR-453-X79-17B050$130.mif
V1
17B-111
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
PARAMETER
DEFINITION
NOTES
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80C.
No load 16%
Full load 85%
Check that the pedal mechanism has not seized.
Check the cleanliness and condition of the pedal potentiometer connections, component code 921 and the
injection computer connections, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Disconnect the battery and the injection computer.
Use the "Universal bornier" to check the insulation and continuity of the following connections:
3LT between components 120 and 921,
3LR between components 120 and 921,
3LS between components 120 and 921,
3LV between components 120 and 921,
3LU between components 120 and 921,
3LW between components 120 and 921.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
In the event of a fault, apply the interpretation of DF974 Pedal potentiometer circuit gang 1 and DF975 Pedal
potentiometer circuit gang 2.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_PR030 / V42_V06_PR030
MR-453-X79-17B050$130.mif
V1
17B-112
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
REFRIGERANT PRESSURE
PR037
PARAMETER
DEFINITION
NOTES
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80C.
The refrigerant pressure must be between 2 bar < PR037 < 27 bar.
Check the cleanliness and condition of the refrigerant pressure sensor and its connections, component code
1202 and the injection computer connections, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Disconnect the battery and the injection computer.
Using the universal bornier in place of the computer, check for insulation and continuity on the following
connections:
38Y between components 120 and 1202,
38X between components 120 and 1202,
38U between components 120 and 1202.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the refrigerant pressure sensor. (see MR 388 or 451, Mechanical, 62A, Air
conditioning, Pressure sensor: Removal - Refitting).
(see MR 388 or 451, Mechanical, 62A, Air conditioning: Precautions for repair) and (see MR 388 or 451,
Mechanical, Air conditioning: Parts and consumables for the repair).
If the fault is present, check the air conditioning circuit (see MR 388 or 451, Mechanical, 62A, Air conditioning:
Check).
AFTER REPAIR
V42_V04_PR037 / V42_V06_PR037
MR-453-X79-17B050$130.mif
V1
17B-113
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
ENGINE SPEED
PR055
PARAMETER
DEFINITION
AFTER REPAIR
V42_V04_PR055 / V42_V06_PR055
MR-453-X79-17B050$130.mif
V1
17B-114
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
PARAMETER
DEFINITION
AFTER REPAIR
V42_V04_PR059 / V42_V06_PR059
MR-453-X79-17B050$130.mif
V1
17B-115
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
COOLANT TEMPERATURE
PR064
PARAMETER
DEFINITION
NOTES
AFTER REPAIR
V42_V04_PR064 / V42_V06_PR064
MR-453-X79-17B050$130.mif
V1
17B-116
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
PARAMETER
DEFINITION
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant temperature > 80C.
The voltage should be between:
9 V < PR071 < 16 V
In the event of a fault, run fault finding on the charging circuit (see 16A, Checking the charging circuit) and refer
to the interpretation of DF047 Computer supply voltage.
AFTER REPAIR
V42_V04_PR071 / V42_V06_PR071
MR-453-X79-17B050$130.mif
V1
17B-117
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
VEHICLE SPEED
PR089
PARAMETER
DEFINITION
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant temperature > 80C.
Carry out a road test, observing the vehicle speed on the instrument panel and the information given by the
diagnostic tool.
If there is an inconsistency between the two values, run complete fault finding on the ABS computer (see 38C, ABS).
AFTER REPAIR
V42_V04_PR089 / V42_V06_PR089
MR-453-X79-17B050$130.mif
V1
17B-118
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
PR097
PARAMETER
DEFINITION
17B
This parameter indicates the programmed throttle valve upper stop value as a %.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature > 80C
The value must be 9%.
In the event of a fault, apply the interpretation of ET051 Throttle stop programming.
AFTER REPAIR
V42_V04_PR097 / V42_V06_PR097
MR-453-X79-17B050$130.mif
V1
17B-119
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
PARAMETER
DEFINITION
Conformity check with the engine running and engine coolant temperature > 80C
The upstream oxygen sensor voltage must be between:
20 mV < PR098 < 1395 mV.
In the event of a fault, apply interpretation of DF092 Upstream oxygen sensor circuit.
AFTER REPAIR
V42_V04_PR098 / V42_V06_PR098
MR-453-X79-17B050$130.mif
V1
17B-120
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
PARAMETER
DEFINITION
Conformity check with the engine running and engine coolant temperature > 80C
The downstream oxygen sensor voltage must be between:
0 mV < PR099 < 1000 mV.
In the event of a fault, apply interpretation of DF093 Downstream oxygen sensor circuit.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_PR099 / V42_V06_PR099
MR-453-X79-17B050$130.mif
V1
17B-121
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
PARAMETER
DEFINITION
This parameter indicates the canister bleed solenoid valve opening cyclic ratio in %.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature > 80C
The value must be between 0% and 100%.
* ocr = opening cyclic ratio
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_PR102 / V42_V06_PR102
MR-453-X79-17B050$130.mif
V1
17B-122
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
PARAMETER
DEFINITION
Conformity check with the engine running and engine coolant temperature > 80C
With the engine idling, the value must be 13%.
If there is a fault, use the interpretation of DF095 Throttle potentiometer circuit gang 1.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_PR118 / V42_V06_PR118
MR-453-X79-17B050$130.mif
V1
17B-123
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
PARAMETER
DEFINITION
Conformity check with the engine running and engine coolant temperature > 80C
With the engine idling, the value must be 13%.
If there is a fault, use the interpretation of DF096 Throttle potentiometer circuit gang 2.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_PR119 / V42_V06_PR119
MR-453-X79-17B050$130.mif
V1
17B-124
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
RICHNESS CORRECTION
PR138
PARAMETER
DEFINITION
Conformity check with the engine running and engine coolant temperature > 80C
This value changes according to the richness signals from the computer.
The richness correction value must be 50%.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_PR138 / V42_V06_PR138
MR-453-X79-17B050$130.mif
V1
17B-125
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
PARAMETER
DEFINITION
Conformity check with the engine running and engine coolant temperature > 80C
Check the sealing of the fuel vapour absorber bleed.
Repair if necessary.
With the engine warm in the idle speed regulation phase, look at parameter PR139.
If the parameter goes to MAXIMUM stop, there is not enough fuel or too much air in the mixture.
If the parameter goes to MINIMUM stop, there is too much fuel or not enough air in the mixture.
Check the cleanliness and correct operation of:
petrol filter,
petrol pump,
fuel circuit,
tank,
air supply pipe,
air filter,
plugs.
Repair if necessary.
Check:
the compressions,
the valve clearance,
the ignition.
Repair if necessary.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_PR139 / V42_V06_PR139
MR-453-X79-17B050$130.mif
V1
17B-126
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
PARAMETER
DEFINITION
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant temperature > 80C.
The value must be 0.72 V and varies according to the status of the pedal.
In the event of a fault, apply the interpretation of fault DF974 Pedal potentiometer circuit gang 1.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_PR147 / V42_V06_PR147
MR-453-X79-17B050$130.mif
V1
17B-127
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
PARAMETER
DEFINITION
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant temperature > 80C.
The value must be 0.52 V and varies according to the status of the pedal.
In the event of a fault, apply the interpretation of fault DF975 Pedal potentiometer circuit gang 2.
AFTER REPAIR
V42_V04_PR148 / V42_V06_PR148
MR-453-X79-17B050$130.mif
V1
17B-128
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
PARAMETER
DEFINITION
This parameter indicates the supply voltage no. 1 of the sensors in Volts.
Conformity check: Engine stopped and the ignition on, or the engine running and the engine coolant
temperature > 80C without electrical consumers.
The voltage of PR215 is approximately 5000 mV.
In the event of a fault, run fault finding on the charging circuit and consult the interpretation of DF011 Sensor
supply voltage no. 1.
AFTER REPAIR
V42_V04_PR215 / V42_V06_PR215
MR-453-X79-17B050$130.mif
V1
17B-129
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
PARAMETER
DEFINITION
This parameter indicates the supply voltage no. 2 of the sensors in Volts.
Conformity check: Engine stopped and the ignition on, or the engine running and the engine coolant
temperature > 80C without electrical consumers.
The voltage of PR216 is approximately 5000 mV.
In the event of a fault, run fault finding on the charging circuit and consult the interpretation of DF012 Sensor
supply voltage no. 2.
AFTER REPAIR
V42_V04_PR216 / V42_V06_PR216
MR-453-X79-17B050$130.mif
V1
17B-130
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
MANIFOLD PRESSURE
PR312
PARAMETER
DEFINITION
Conformity check with the engine running and engine coolant temperature > 80C
With the engine idling, the value must be 500 mbar.
With the engine running and throttle open, the value must be 1000 mbar.
AFTER REPAIR
V42_V04_PR312 / V42_V06_PR312
MR-453-X79-17B050$130.mif
V1
17B-131
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
PARAMETER
DEFINITION
Conformity check with the engine running and engine coolant temperature > 80C
This parameter varies according to the pinking status in the combustion chamber.
In the event of a fault, apply the interpretation of fault DF088 Pinking sensor circuit.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_PR427 / V42_V06_PR427
MR-453-X79-17B050$130.mif
V1
17B-132
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
PARAMETER
DEFINITION
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature > 80C
Without action on the accelerator pedal, the value must be 10%.
When the accelerator pedal is fully depressed, the value must be 85%.
In the event of a fault, apply the interpretation of faults DF095 Throttle potentiometer circuit gang 1 and DF096
Throttle potentiometer circuit gang 2.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_PR429 / V42_V06_PR429
MR-453-X79-17B050$130.mif
V1
17B-133
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
PARAMETER
DEFINITION
This parameter indicates the built-in correction for idle speed regulation in N.m.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature > 80C
The built-in idle speed regulation correction is continuously calculated to take into account consumer air demand.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_PR444 / V42_V06_PR444
MR-453-X79-17B050$130.mif
V1
17B-134
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
PARAMETER
DEFINITION
This parameter indicates the heating resistance of the downstream oxygen sensor in
Ohms.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature > 80C
The value must be 9 at 20C.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_PR446 / V42_V06_PR446
MR-453-X79-17B050$130.mif
V1
17B-135
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
PARAMETER
DEFINITION
This parameter indicates the heating resistance of the downstream oxygen sensor
in Ohms.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature > 80C
The value must be 9 at 20C.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_PR447 / V42_V06_PR447
MR-453-X79-17B050$130.mif
V1
17B-136
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
IGNITION ADVANCE
PR448
PARAMETER
DEFINITION
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature > 80C
The value must be 0 V with the ignition on and 4 V at idle speed.
In the event of a fault, apply the interpretation of fault DF120 Engine speed sensor signal.
AFTER REPAIR
V42_V04_PR448 / V42_V06_PR448
MR-453-X79-17B050$130.mif
V1
17B-137
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
PARAMETER
DEFINITION
This parameter indicates the throttle valve gang 2 voltage measured in volts.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80C
The value must be 0.60 V.
In the event of a fault, apply the interpretation of fault DF096 Throttle potentiometer circuit gang 2.
AFTER REPAIR
V42_V04_PR538 / V42_V06_PR538
MR-453-X79-17B050$130.mif
V1
17B-138
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
PARAMETER
DEFINITION
This parameter indicates the throttle valve voltage, gang 1 measured in volts.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature > 80C
The value must be 0.35 V.
In the event of a fault, apply the interpretation of fault DF095 Throttle potentiometer circuit gang 1.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_PR539 / V42_V06_PR539
MR-453-X79-17B050$130.mif
V1
17B-139
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Interpretation of parameters
17B
PARAMETER
DEFINITION
This parameter indicates the number of active heating resistors and can be between 0
to 5 depending on the relays activated.
0 if no relay is active
1 if relay 1 is active
2 if relay 2 is active
3 if relays 1 and 2 are active
4 if relays 2 and 3 are active
5 if all of the relays are active
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant temperature < 80C
In the event of a fault, consult the interpretation of faults:
DF992 Additional heater relay 1 circuit,
DF993 Additional heater relay 2 circuit,
DF994 Additional heater relay 3 circuit.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_PR814 / V42_V06_PR814
MR-453-X79-17B050$130.mif
V1
17B-140
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Command summary table
Tool
command
17B
Comments
RZ001
Fault memory
RZ003
Engine adaptives
RZ031
RZ033
Richness regulation
programming
RZ037
Flywheel target
programming
AC005
Cylinder 1 injector
AC006
Cylinder 2 injector
AC007
Cylinder 3 injector
AC008
Cylinder 4 injector
AC015
AC017
AC027
Motorised throttle
AC038
AC039
AC180
AC217
AC224
MR-453-X79-17B050$140.mif
V1
17B-141
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Command summary table
17B
AC250
AC251
AC252
SC001
SC003
SC006
SC007
VP010
Enter VIN.
VP036
VP037
MR-453-X79-17B050$140.mif
V1
17B-142
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Customer complaints
NOTES
17B
Special note:
Only address this customer complaint after a complete check with the diagnostic
tool.
ALP 1
ALP 2
ALP 3
ALP 4
ALP 5
COOLANT LEAK
ALP 6
ALP 7
FUEL ODOUR
ALP 8
ALP 9
EXHAUST SMOKE
ALP 10
ALP 11
ALP 12
MR-453-X79-17B050$150.mif
V1
17B-143
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Customer complaints
17B
EXCESSIVE CONSUMPTION
ALP 13
ALP 14
ALP 15
ENGINE STARTING
ALP 16
ALP 17
ALP 18
PERFORMANCE
ALP 19
ACCELERATION GAP
ALP 20
DRIVING PLEASURE
ROUGH IDLE
ALP 21
ALP 22
JERKING OR HESITATION
ALP 23
ENGINE STALLS
ALP 24
ERRATIC ACCELERATION
ALP 25
ERRATIC DECELERATION
ALP 26
ALP 27
MR-453-X79-17B050$150.mif
V1
17B-144
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 1
NOTES
17B
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Try to establish dialogue with a computer on another vehicle to make sure that the diagnostic tool is not faulty. If
the tool is not the cause and communication cannot be established with any other computer on the same vehicle,
it is possible that another computer is disrupting the multiplex network.
Check the voltage of the battery.
If the battery voltage is between 9.5 V and 17.5 V, run fault finding on the charging circuit.
Check the presence and condition of the injection fuses on the UPC and in the engine fuse box.
Check the connection of the computer connectors, component code 120.
Check the injection computer earths (quality, oxidation, tightness of the earth bolts on the battery terminal).
Check that the supply to the computer is correct:
Earth on connection NH of component 120,
+ 12V on connection 3FB of component 120.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check that the diagnostic socket, component code 225 is correctly supplied:
+ Before ignition feed on connection BP56 of component 225,
+ After ignition feed on connection AP10 of component 225,
Earth on connections MAM and NC of component 225.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If dialogue has still not been established after these checks, contact the techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP1 / V42_V06_ALP1
MR-453-X79-17B050$160.mif
V1
17B-145
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 2
17B
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP2 / V42_V06_ALP2
MR-453-X79-17B050$160.mif
V1
17B-146
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 3
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP3 / V42_V06_ALP3
MR-453-X79-17B050$160.mif
V1
17B-147
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 4
17B
Fuel leak
Check the fuel pump relay by running TEST 1 Fuel supply pump relay check.
Check the air pipes.
Check the additional fuel circuit solenoid valve by running TEST 5 Checking the additional fuel tank.
Check the spark plugs.
Check the injector rail.
Check the additional petrol circuit pump by running TEST 12 Additional fuel tank pump check.
If the fault is still present, contact the Techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP4 / V42_V06_ALP4
MR-453-X79-17B050$160.mif
V1
17B-148
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 5
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP5 / V42_V06_ALP5
MR-453-X79-17B050$160.mif
V1
17B-149
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 6
Coolant leak
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP6 / V42_V06_ALP6
MR-453-X79-17B050$160.mif
V1
17B-150
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 7
Unusual odour
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP7 / V42_V06_ALP7
MR-453-X79-17B050$160.mif
V1
17B-151
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 8
Fuel odours
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP8 / V42_V06_ALP8
MR-453-X79-17B050$160.mif
V1
17B-152
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 9
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP9 / V42_V06_ALP9
MR-453-X79-17B050$160.mif
V1
17B-153
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 10
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP10 / V42_V06_ALP10
MR-453-X79-17B050$160.mif
V1
17B-154
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 11
17B
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP11 / V42_V06_ALP11
MR-453-X79-17B050$160.mif
V1
17B-155
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 12
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP12 / V42_V06_ALP12
MR-453-X79-17B050$160.mif
V1
17B-156
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 13
17B
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP13 / V42_V06_ALP13
MR-453-X79-17B050$160.mif
V1
17B-157
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 14
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP14 / V42_V06_ALP14
MR-453-X79-17B050$160.mif
V1
17B-158
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 15
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP15 / V42_V06_ALP15
MR-453-X79-17B050$160.mif
V1
17B-159
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 16
17B
Check the fuel pump relay by running TEST 1 Petrol supply pump relay check.
Check the air filter unit.
Check the oil.
Check the air pipes.
Check the additional fuel circuit solenoid valve by running TEST 5 Checking the additional fuel tank.
Check the spark plugs.
Check the injector rail.
Check the additional petrol circuit pump by running TEST 12 Additional fuel tank pump check.
Check the TDC sensor by running TEST 10 TDC sensor check.
Check the coolant pump.
Check the cylinder head.
Check the camshaft.
Check the valves.
Check the timing.
Check the rotating parts.
Check the accessories belt.
Check the supply relay and the injection computer.
If the fault is still present, contact the Techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP16 / V42_V06_ALP16
MR-453-X79-17B050$160.mif
V1
17B-160
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 17
17B
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP17 / V42_V06_ALP17
MR-453-X79-17B050$160.mif
V1
17B-161
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 18
17B
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP18 / V42_V06_ALP18
MR-453-X79-17B050$160.mif
V1
17B-162
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 19
17B
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP19 / V42_V06_ALP19
MR-453-X79-17B050$160.mif
V1
17B-163
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
17B
ALP 19
CONTINUED
Check the downstream oxygen sensor by running TEST 18 Checking the downstream O2 sensor.
Check the catalytic converter.
Check the exhaust manifold.
Check the pistons and piston rings.
Check the cylinder head.
Check the camshaft.
Check the valves.
Check the timing.
Check the rotating parts.
Check the injection computer.
If the fault is still present, contact the Techline.
AFTER REPAIR
MR-453-X79-17B050$160.mif
V1
Carry out a road test, then check with the diagnostic tool.
17B-164
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 20
17B
Check the accelerator pedal potentiometer by running TEST 8 Accelerator pedal potentiometer check.
Check the brake pedal switch by running TEST 9 Brake pedal switch check.
Check the air filter unit.
Check the inlet manifold air pressure sensor by running TEST 7 Air inlet pressure sensor check.
Check the air pipes.
Check the air inlet temperature sensor by running TEST 6 Checking the air temperature sensor.
Check the throttle valve by running TEST 3 Throttle valve check.
Check the additional fuel circuit solenoid valve by running TEST 5 Checking the additional fuel tank.
Check the spark plugs.
Check the injector rail.
Check the inlet manifold.
Check the ignition coil by running TEST 14 Checking the ignition coil.
Check the injectors by running TEST 13 Checking the injectors.
Check the additional petrol circuit pump by running TEST 12 Additional fuel tank pump check.
Check the TDC sensor by running TEST 10 TDC sensor check.
Check the pinking sensor by running TEST 11 Pinking sensor check.
Check the upstream oxygen sensor by running TEST 17 Checking the upstream O2 sensor.
Check the downstream oxygen sensor by running TEST 18 Checking the downstream O2 sensor.
Check the catalytic converter.
Check the camshaft.
Check the valves.
Check the timing.
Check the injection computer.
If the fault is still present, contact the Techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP20 / V42_V06_ALP20
MR-453-X79-17B050$160.mif
V1
17B-165
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 21
17B
Rough idle
Check the alternator charge signal module by running TEST 2 Alternator signal module check.
Check the accelerator pedal potentiometer by running TEST 8 Accelerator pedal potentiometer check.
Check the air filter unit.
Check the inlet manifold air pressure sensor by running TEST 7 Air inlet pressure sensor check.
Check the throttle valve by running TEST 3 Throttle valve check.
Check the additional fuel circuit solenoid valve by running TEST 5 Checking the additional fuel tank.
Check the spark plugs.
Check the injector rail.
Check the inlet manifold.
Check the ignition coil by running TEST 14 Checking the ignition coil.
Check the injectors by running TEST 13 Checking the injectors.
Check the additional petrol circuit pump by running TEST 12 Additional fuel tank pump check.
Check the upstream oxygen sensor by running TEST 17 Checking the upstream O2 sensor.
Check the downstream oxygen sensor by running TEST 18 Checking the downstream O2 sensor.
Check the cylinder head.
Check the camshaft.
Check the valves.
Check the timing.
Check the rotating parts.
Check the injection computer.
Check the injection pump.
If the fault is still present, contact the Techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP21 / V42_V06_ALP21
MR-453-X79-17B050$160.mif
V1
17B-166
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 22
17B
Check the alternator charge signal module by running TEST 2 Alternator signal module check.
Check the accelerator pedal potentiometer by running TEST 8 Accelerator pedal potentiometer check.
Check the air filter unit.
Check the air inlet temperature sensor by running TEST 6 Checking the air temperature sensor.
Check the throttle valve by running TEST 3 Throttle valve check.
Check the additional fuel circuit solenoid valve by running TEST 5 Checking the additional fuel tank.
Check the coolant temperature sensor by running TEST 15 Coolant temperature sensor check.
Check the spark plugs.
Check the injector rail.
Check the inlet manifold.
Check the additional petrol circuit pump by running TEST 12 Additional fuel tank pump check.
Check the upstream oxygen sensor by running TEST 17 Checking the upstream O2 sensor.
Check the downstream oxygen sensor by running TEST 18 Checking the downstream O2 sensor.
Check the cylinder head.
Check the camshaft.
Check the valves.
Check the timing.
Check the injection computer.
If the fault is still present, contact the Techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP22 / V42_V06_ALP22
MR-453-X79-17B050$160.mif
V1
17B-167
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 23
17B
Jerking or hesitation
Check the alternator charge signal module by running TEST 2 Alternator signal module check.
Check the fuel pump relay by running TEST 1 Petrol supply pump relay check.
Check the accelerator pedal potentiometer by running TEST 8 Accelerator pedal potentiometer check.
Check the brake pedal switch by running TEST 9 Brake pedal switch check.
Check the air filter unit.
Check the inlet manifold air pressure sensor by running TEST 7 Air inlet pressure sensor check.
Check the air pipes.
Check the air inlet temperature sensor by running TEST 6 Checking the air temperature sensor.
Check the throttle valve by running TEST 3 Throttle valve check.
Check the additional fuel circuit solenoid valve by running TEST 5 Checking the additional fuel tank.
Check the spark plugs.
Check the injector rail.
Check the inlet manifold.
Check the ignition coil by running TEST 14 Checking the ignition coil.
Check the injectors by running TEST 13 Checking the injectors.
Check the additional petrol circuit pump by running TEST 12 Additional fuel tank pump check.
Check the TDC sensor by running TEST 10 TDC sensor check.
Check the upstream oxygen sensor by running TEST 17 Checking the upstream O2 sensor.
Check the downstream oxygen sensor by running TEST 18 Checking the downstream O2 sensor.
Check the camshaft.
Check the valves.
Check the timing.
Check the supply relay and the injection computer.
If the fault is still present, contact the Techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP23 / V42_V06_ALP23
MR-453-X79-17B050$160.mif
V1
17B-168
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 24
17B
Engine stalls
Check the fuel pump relay by running TEST 1 Petrol supply pump relay check.
Check the air filter unit.
Check the inlet manifold air pressure sensor by running TEST 7 Air inlet pressure sensor check.
Check the air pipes.
Check the additional fuel circuit solenoid valve by running TEST 5 Checking the additional fuel tank.
Check the injector rail.
Check the injectors by running TEST 13 Checking the injectors.
Check the additional petrol circuit pump by running TEST 12 Additional fuel tank pump check.
Check the TDC sensor by running TEST 10 TDC sensor check.
Check the upstream oxygen sensor by running TEST 17 Checking the upstream O2 sensor.
Check the downstream oxygen sensor by running TEST 18 Checking the downstream O2 sensor.
Check the camshaft.
Check the valves.
Check the timing.
Check the injection computer.
Check the injection computer supply relay.
If the fault is still present, contact the Techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP24 / V42_V06_ALP24
MR-453-X79-17B050$160.mif
V1
17B-169
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 25
17B
Erratic acceleration
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP25 / V42_V06_ALP25
MR-453-X79-17B050$160.mif
V1
17B-170
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 26
17B
Erratic deceleration
Check the inlet manifold air pressure sensor by running TEST 7 Air inlet pressure sensor check.
Check the throttle valve by running TEST 3 Throttle valve check.
If the fault is still present, contact the Techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP26 / V42_V06_ALP26
MR-453-X79-17B050$160.mif
V1
17B-171
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Fault Finding Chart
ALP 27
17B
Check the accelerator pedal potentiometer by running TEST 8 Accelerator pedal potentiometer check.
Check the throttle valve by running TEST 3 Throttle valve check.
Check the injection computer.
If the fault is still present, contact the Techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_ALP27 / V42_V06_ALP27
MR-453-X79-17B050$160.mif
V1
17B-172
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Test summary table
17B
TEST 1
TEST 2
TEST 3
TEST 4
TEST 5
TEST 6
TEST 7
TEST 8
TEST 9
TEST 10
TEST 11
TEST 12
Injector check
TEST 13
TEST 14
TEST 15
TEST 16
TEST 17
TEST 18
TEST 19
MR-453-X79-17B050$170.mif
V1
17B-173
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Tests
TEST 1
17B
Listen to the operation of the fuel supply pump, as well as the fuel pump relay by running command AC015 Fuel
pump relay.
Check the fuel pump supply on connection 3NA by running command AC015 Fuel pump relay.
Check the continuity, insulation, and absence of interference resistance on the following connections:
3NA between components 1047 and 833,
MG between component 833 and the earth.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_TEST1 / V42_V06_TEST1
MR-453-X79-17B050$180.mif
V1
17B-174
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Tests
TEST 2
NOTES
17B
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
With the engine running, check the alternator charge without any electrical consumers switched on using PR002
Alternator charge, then switch on the consumers and check the increase in PR002.
Check the cleanliness and condition of the alternator connector, component code 103 and of the injection
computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connection:
2K between components 103 and 120.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the check is correct, replace the alternator signal module, component code 103 (see MR 388 or 451,
Mechanical, 16A, Starting - Charging, Alternator: Removal - Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_TEST2 / V42_V06_TEST2
MR-453-X79-17B050$180.mif
V1
17B-175
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Tests
TEST 3
17B
Check that parameter PR444 Idling speed regulation integral correction is between:
5 N.m < PR444 < 10 N.m.
The attempt is made with the engine idling and warm (75C), without any electrical consumers switched on.
The value of PR444 must be read at least 20 minutes after the engine coolant temperature has reached 75C.
If the value of PR444 is greater than 10 N.m, program the throttle again using command RZ031 Throttle stop
programming.
If the value of PR444 is less than -5N.m, check the fitting of the throttle and check for possible air leaks
(see MR 388 or MR451, Mechanical, 12A, Fuel mixture, Throttle valve: Removal Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_TEST3 / V42_V06_TEST3
MR-453-X79-17B050$180.mif
V1
17B-176
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Tests
TEST 4
NOTES
17B
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the cleanliness, mounting, possible leaks and the hoses of the fuel vapour absorber solenoid valve,
component code 371 (see MR 388, Mechanical, 14A, Emission control, Fuel vapour recirculation circuit:
Check or MR 451, Mechanical, 14A, Emission control, Fuel vapour absorber: Removal - Refitting).
Listen to the operation of the solenoid valve by running command AC017 Canister bleed solenoid valve.
With the engine idling, disconnect the pipe at the solenoid valve inlet and check that there is no suction on your
finger. (These steps allow the sealing of the solenoid valve to be checked for air tightness.)
Check the cleanliness and condition of the canister bleed solenoid valve connector, component code 371 and
of the injection computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
3FB between components 371 and 1047,
3BB between components 371 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the ignition on, check for + 12 V on connection 3FB of component 371.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the resistance of the fuel vapour absorber bleed solenoid valve.
If the resistance of the fuel vapour absorber bleed solenoid valve is not between: 24 < X < 30 between 0C
and 40C, replace the fuel vapour absorber bleed solenoid valve (see MR 388 or 451, Mechanical, 14A, Emission
control, Fuel vapour absorber: Removal - Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_TEST4 / V42_V06_TEST4
MR-453-X79-17B050$180.mif
V1
17B-177
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Tests
TEST 5
NOTES
17B
Check the cleanliness, mounting, possible leaks and the solenoid valve hoses (see MR 388 Mechanical, 19C,
Tank, Additional fuel system petrol pump: Removal Refitting).
Listen to the operation of the solenoid valve by running command AC217 Additional petrol circuit solenoid
valve.
Check the cleanliness and condition of the connector of the additional petrol circuit solenoid valve, component
code 1640 and of the injection computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the continuity, insulation, and absence of interference resistance on the following connections:
3ACM between components 1640 and 120,
3FB between components 1640 and 1047.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the supply of the solenoid valve using a test light, by running command AC224 Additional petrol circuit
pump relay.
Check the internal resistance of the solenoid valve, component code 1640 on the computer connector, component
code 120, its value must be between: 24 < X 30 . If the resistance is not correct, replace the solenoid valve
(see MR 388 Mechanical, 19C, Tank, Additional fuel system petrol pump: Removal Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_TEST5 / V42_V06_TEST5
MR-453-X79-17B050$180.mif
V1
17B-178
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Tests
TEST 6
17B
Perform a visual inspection and look for possible sealing faults in the system.
Ensure the conformity of the system (see MR 388 or 451, Mechanical, 12A, Fuel mixture, Air inlet: Description).
If the fault is still present, contact the Techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_TEST6 / V42_V06_TEST6
MR-453-X79-17B050$180.mif
V1
17B-179
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Tests
TEST 7
17B
Check the fitting and sealing of the inlet air pressure sensor, component code 147 (condition of the seals) and look
for possible leaks on the inlet air pipe. Ensure the conformity of the system (see MR 388 or 451, Mechanical, 12A,
Fuel mixture, Air inlet: Description).
With the ignition on, compare the value of PR312 Manifold pressure for the vehicle concerned with that given by
another vehicle (absolute difference < 130 mbars).
Check the connection and condition of the connector of the inlet air pressure sensor, component code 147 and
of the injection computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the supply voltage of the sensor on connections 3AJR and 3AJP.
Check the insulation, continuity and the absence of interference resistance on the following connections:
3AJP between components 120 and 147,
3AJR between components 120 and 147,
3AJQ between components 120 and 147.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the ignition on, use a vacuum pump in order to create a variation in negative pressure. Then use the diagnostic
tool to check that PR312 Manifold pressure 500 mbar.
Replace the inlet air pressure sensor, component code 147 (see MR 388 or 451, Mechanical, 12A, Fuel mixture,
Air inlet: Description) and repeat the vacuum test.
If the fault is still present, contact the Techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_TEST7 / V42_V06_TEST7
MR-453-X79-17B050$180.mif
V1
17B-180
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Tests
TEST 8
NOTES
17B
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the variation in PR055 Engine speed when depressing the accelerator pedal (with the engine running).
Stop the engine and switch on the ignition. Without action on the pedal, check that the voltage correction of circuit 1:
PR147 Pedal potentiometer voltage gang 1 is less than 817 mV and
PR148 Pedal potentiometer voltage gang 2 is less than 440 mV.
Then, in the "full load" position, check the voltage of circuit 1: PR147 must be greater than 4185 mV and PR148
must be greater than 2013 mV.
Also check the pedal position in the following cases:
"position zero" (PR030 Accelerator pedal position = 0)
"Full load" (PR030 = 1).
Stop the engine and then switch on the ignition.
With the vehicle under + after ignition feed, measure the voltage between the following connections:
3LR and 3LT of component 921,
3LU and 3LV of component 921.
If the value is not between 4.75 V X 5.25 V, check the insulation, the continuity and the absence of
interference resistance of the following connections:
3LR between components 120 and 921,
3LT between components 120 and 921,
3LU between components 120 and 921,
3LV between components 120 and 921.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation, continuity and the absence of interference resistance on the following connections:
3LS between components 120 and 921,
3LW between components 120 and 921.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_TEST8 / V42_V06_TEST8
MR-453-X79-17B050$180.mif
V1
17B-181
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Tests
17B
TEST 8
CONTINUED
Remove the accelerator pedal, component code 921 (see MR 388, Mechanical, 17B, Petrol injection,
Accelerator pedal potentiometer: Removal Refitting or 451, Mechanical, 37A, Mechanical component
controls, Accelerator pedal: Removal Refitting).
Without action on the accelerator pedal, check the resistance between the following connections:
Gang 1:
3LT and 3LS of component 921, the resistance must be between 718 X 5263 ,
3LT and 3LR of component 921, the resistance must be between 838 X 1742 ,
3LR and 3LS of component 921, the resistance must be between 1312 X 6495 .
Gang 2:
3LV and 3LW of component 921, the resistance must be between 701 X 5242 ,
3LV and 3LU of component 921, the resistance must be between 1495 X 3105 ,
3LU and 3LW of component 921, the resistance must be between 1978 X 7894 .
If these checks are incorrect, replace the accelerator pedal sensor, component code 921 (see MR 388,
Mechanical, 17B, Petrol injection, Accelerator pedal potentiometer: Removal Refitting or MR 451,
Mechanical, 37A, Mechanical component controls, Accelerator pedal: Removal Refitting).
If the fault is still present, contact the Techline.
With the accelerator pedal depressed to the end of travel, check the resistance between the following
connections:
Gang 1:
3LT and 3LS of component 921, the resistance must be between 1361 X 6600 ,
3LT and 3LR of component 921, the resistance must be between 838 X 1742 ,
3LR and 3LS of component 921, the resistance must be between 668 X 5160 .
Gang 2:
3LV and 3LW of component 921, the resistance must be between 1276 X 6436 ,
3LV and 3LU of component 921, the resistance must be between 1495 X 3105 ,
3LU and 3LW of component 921, the resistance must be between 1403 X 6700 .
If these checks are incorrect, replace the accelerator pedal sensor, component code 921 (see MR 388,
Mechanical, 17B, Petrol injection, Accelerator pedal potentiometer: Removal Refitting or MR 451,
Mechanical, 37A, Mechanical component controls, Accelerator pedal: Removal Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIR
MR-453-X79-17B050$180.mif
V1
Carry out a road test, then check with the diagnostic tool.
17B-182
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Tests
TEST 9
NOTES
17B
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
With the brake pedal released, check ET039 Brake pedal and ET799 Brake wire contact.
ET039 must be 01 and ET799 must be 01.
While depressing the brake pedal, check ET039 and ET799.
ET039 must be 02 and ET799 must be 02.
If these two checks are correct, the switch is not faulty.
Check the fitting and mechanical operation of the brake pedal (the pedal returns properly).
If the check is incorrect, check the braking system.
With the brake pedal depressed, measure the resistance of the brake pedal switch, component code 160
between connections AP1 and 65A, the value must be X > 10 M.
If the resistance is not correct, replace the brake pedal switch, component code 160 (see MR 388 or 451,
Mechanical, 37A, Mechanical component controls, Brake pedal switch: Removal - Refitting).
With the brake pedal released, measure the resistance of the brake pedal switch, component code 160 between
connections AP1 and 5A, the value must be between 0 < X < 1 .
If the resistance is not correct, replace the brake pedal switch, component code 160 (see MR 388 or 451,
Mechanical, 37A, Mechanical component controls, Brake pedal switch: Removal - Refitting) and move on
to the part: Checking the brake pedal switch.
Check the condition of the brake pedal switch connector, component code 160 (see MR 388 or 451, Mechanical,
37A, Mechanical component controls, Brake pedal switch: Removal - Refitting).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the presence and condition of the brake pedal fuse F03 (10 A).
Check the insulation, continuity and the absence of interference resistance on the following connections:
AP1 between components 160 and 1016,
5A between components 160 and 120,
65A between components 160 and120,
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_TEST9 / V42_V06_TEST9
MR-453-X79-17B050$180.mif
V1
17B-183
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Tests
TEST 10
NOTES
17B
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the fitting of the sensor (connectors, mountings, etc.) (see MR 388 or 451, Mechanical, 17B, Petrol
injection, Crankshaft position sensor: Removal - Refitting).
Switch on the ignition, check the change of the engine rotation speed using parameter PR055 Engine speed.
The value must be between 0 rpm and more than 120 rpm when the starter is operating.
With the engine running, accelerate to obtain different engine rotation speeds and check that the engine speed
correctly changes in relation to the accelerations.
If PR055 varies, the sensor is sound.
Check the cleanliness and condition of the TDC sensor, component code 149 and of the injection computer
connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the resistance of the TDC sensor between connections 3BL and 3BG on the injection computer
connector side, component code 120 (see MR 388 or 451, Mechanical, 17B, Petrol injection, Petrol injection
computer: Removal - Refitting).
The resistance must be between 175 X 295 . If the value is not correct, replace the sensor (see MR 388
or 451, Mechanical, 17B, Petrol injection, Crankshaft position sensor: Removal - Refitting).
Check the insulation, continuity and the absence of interference resistance on the following connections:
3BL between components 120 and 149,
3BG between components 120 and 149.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_TEST10 / V42_V06_TEST10
MR-453-X79-17B050$180.mif
V1
17B-184
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Tests
TEST 11
NOTES
17B
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Start the engine and let it idle. Then, check that PR427 Average pinking signal is 0.
With the engine idling, check that parameters PR469 Cylinder 1 pinking value, PR471 Cylinder 2 pinking value,
PR473 Cylinder 3 pinking value, PR475 Cylinder 4 pinking value are all 0.
Check the cleanliness and condition of the pinking sensor connector, component code 146 and of the injection
computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the resistance of the pinking sensor between connections 3DQ and 3S on the injection computer
connector side, component code 120 (see MR 388 or 451, Mechanical, 17B, Petrol injection, Petrol injection
computer: Removal - Refitting).
The resistance must be: X > 10 M.
If the resistance value is not correct, replace the pinking sensor (see MR 388 or 451, Mechanical, 17B, Petrol
injection, Petrol injection: List and location of components).
Check the insulation, continuity and the absence of interference resistance on the following connections:
3DQ between components 120 and 146,
3S between components 120 and 146.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_TEST11 / V42_V06_TEST11
MR-453-X79-17B050$180.mif
V1
17B-185
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Tests
TEST 12
NOTES
17B
Listen to the operation of the additional fuel pump and of the petrol pump relay of the additional circuit by running
command AC224 Additional petrol circuit pump relay.
Check the supply of the solenoid valve using a test light, by running command AC224.
If the supply is correct, replace the additional fuel pump (see MR 388 Mechanical, 19C, Tank, Additional fuel
circuit tank: Removal Refitting).
Check the continuity, insulation, and absence of interference resistance on the following connections:
3ACL between components 1639 and 283,
NH between earth and 283.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the checks are correct, run fault finding on the Protection and Switching Unit.
If the fault is still present, contact the Techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_TEST12 / V42_V06_TEST12
MR-453-X79-17B050$180.mif
V1
17B-186
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Tests
TEST 13
NOTES
17B
Injector check
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Perform a visual inspection of the condition and possible leaks in the system.
Repair if necessary (see MR 388 Mechanical, 13A, Fuel supply, Injector rail Injectors: Removal Refitting
or MR 451, Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal Refitting).
Listen to the operation of the injectors by running the commands:
AC005 Cylinder 1 injector,
AC006 Cylinder 2 injector,
AC007 Cylinder 3 injector,
AC008 Cylinder 4 injector.
Replace the injectors if necessary (see MR 388 Mechanical, 13A, Fuel supply, Injector rail Injectors:
Removal Refitting or MR 451, Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal
Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_TEST13 / V42_V06_TEST13
MR-453-X79-17B050$180.mif
V1
17B-187
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Tests
TEST 14
NOTES
17B
Special note:
To apply this procedure, use special tool El. 1808: Ignition coil tester,
available in the Parts Department catalogue.
part number: 77 11 381 808.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
K4M engine
Perform a visual inspection of the condition of the connectors for the following: pencil ignition coil no.1, component
code 1077, pencil ignition coil no.2, component code 1078, pencil ignition coil no.3, component code 1079, pencil
ignition coil no.4, component code 1080 (see MR 388 or 451, Mechanical, 17A, Ignition, Coils: Removal
Refitting).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Insert tool El. 1808 (1) into the coil.
Place the tool/coil assembly in the spark plug well.
Start the engine and let it idle.
Apply light pressure to the assembly to hold the coil in contact with the tool.
Observe the glow from the electric arc on the spark plug well wall.
If the electric arc is not produced, replace the coil concerned (see MR 388 or 451, Mechanical, 17A, Ignition,
Coils: Removal Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_TEST14 / V42_V06_TEST14
MR-453-X79-17B050$180.mif
V1
17B-188
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Tests
TEST 14
CONTINUED
17B
K7M engine
Perform a visual inspection of the condition of the ignition coil connectors, component code 778 (see MR 388
Mechanical, 17A, Ignition, Coils: Removal Refitting).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Insert tool El.1808 (1) in the cap of the wire of the plugs concerned.
Fit the assembly in the plug well.
Start the engine and let it idle.
Apply light pressure to the assembly to hold the coil in contact with the tool.
Observe the glow from the electric arc on the spark plug well wall.
If the electric arc is not produced, replace the ignition coil (see MR 388 Mechanical, 17A, Ignition, Coils:
Removal Refitting).
If the fault is still present, contact the Techline.
D4D engine
Switch on the vehicle + after ignition feed.
Run command VP036 FUEL SUPPLY INHIBITION.
Put the vehicle under starting conditions:
position of gear lever in neutral for a manual gearbox* or position "P" (Parking) for an automatic gearbox*.
brake pedal depressed.
Run command RZ003 ENGINE ADAPTIVES.
Remove the plugs from each cylinder and check, one after another, that sparks are present by bringing the plug
close to a chassis earth, with the starter engaged. If no spark is produced, replace the ignition coil, component
code 778 (see MR 388 Mechanical, 17A, Ignition, Coils: Removal Refitting).
If the fault is still present, contact the Techline.
BVM*: Manual gearbox.
BVA*: Automatic gearbox.
AFTER REPAIR
MR-453-X79-17B050$180.mif
V1
Carry out a road test, then check with the diagnostic tool.
17B-189
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Tests
TEST 15
NOTES
17B
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_TEST15 / V42_V06_TEST15
MR-453-X79-17B050$180.mif
V1
17B-190
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Tests
TEST 16
NOTES
17B
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the operation of the low speed fan assembly by running command AC038 Low speed fan assembly relay.
Check the operation of the high speed fan assembly by running command AC039 High speed fan assembly
relay.
If these two checks are correct, the fan assembly relay is not faulty
Run command AC038 and use the test light to check for the control signal of component 120 on connection 3JN
of component 700.
Check the connection and condition of the fan assembly connector, component code 188 and of the injection
computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connections:
3JN between components 700 and 120,
49C between components 321 and 700,
49B between components 188 and 321.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Run command AC038 and use the test light to check for the presence of supply at the relay output.
If the supply is absent, replace the low speed fan assembly relay, component code 700.
Run command AC039 and use the test light to check for the control signal of component 120 on connection 3JP
of component 336.
Check the insulation, continuity and absence of interference resistance on the following connection:
49B between components 336 and 188,
3JP between components 336 and 120.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Run command AC039 and use the test light to check for the presence of supply at the relay output.
If the supply is absent, replace the high speed fan assembly relay, component code 336.
If the fault is still present, contact the Techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_TEST16 / V42_V06_TEST16
MR-453-X79-17B050$180.mif
V1
17B-191
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Tests
TEST 17
NOTES
17B
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Visually check the position and mounting of the upstream oxygen sensor (see MR 388 or 451, Mechanical, 17B,
Petrol injection, Oxygen sensors: Removal - Refitting).
With the engine warm, PR064 Coolant temperature > 70C, depress the accelerator pedal and check that PR098
Upstream oxygen sensor voltage varies correctly between: 20 mV < PR098 < 1395 mV. The variation must be
greater than 50 mV.
Check the connection and condition of the upstream oxygen sensor connector, component code 887 and of the
injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connection:
3GH between components 887 and 120,
3GK between components 887 and 120.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the resistance value of the upstream oxygen sensor, component code 887 on the computer connector side,
component code 120. With the engine stopped for 10 minutes, the resistance value should be between 7 and
infinity.
If the resistance is not correct, replace the upstream oxygen sensor, component code 887 (see MR 388 or 451,
Mechanical, 17B, Petrol injection, Oxygen sensors: Removal - Refitting).
Check that the TDC* sensor programming is correct (see the section on Replacement of components).
Run test SC007 Run OBD test: O2 sensor and start the engine (Only depress the brake pedal to authorise the
starting of the engine).
At the end, check the test results:
STATUS1: Run the test again with the engine coolant temperature X > 90C.
STATUS2 or STATUS3: Sensor OK.
STATUS4: Replace the upstream oxygen sensor (see MR 388 or 451, Mechanical, 17B, Petrol injection,
Oxygen sensors: Removal Refitting).
If the fault is still present, contact the Techline.
TDC*: TOP DEAD CENTRE
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_TEST17 / V42_V06_TEST17
MR-453-X79-17B050$180.mif
V1
17B-192
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Tests
TEST 18
NOTES
17B
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Visually check the position and mounting of the downstream oxygen sensor, component code 242 (see MR 388
or 451, Mechanical, 17B, Petrol injection, Oxygen sensors: Removal - Refitting).
With the engine warm, PR064 Coolant temperature > 70C, depress the accelerator pedal for 3 minutes, perform
several accelerations and check that PR099 Downstream oxygen sensor voltage varies correctly between:
0 mV < PR099 < 1000 mV.
Check the connection and condition of the downstream oxygen sensor connector, component code 242 and of the
injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connection:
3GL between components 242 and 120,
3GJ between components 242 and 120.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the resistance value of the downstream oxygen sensor, component code 242 on the computer connector
side, component code 120. With the engine stopped for 10 minutes, the resistance value should be between 7
and infinity.
If the resistance value is not correct, replace the downstream oxygen sensor, component code 242 (see MR 388
or 451, Mechanical, 17B, Petrol injection, Oxygen sensors: Removal - Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_TEST18 / V42_V06_TEST18
MR-453-X79-17B050$180.mif
V1
17B-193
V42 Injection
Program No.: 2A
Vdiag No.: 04, 06
PETROL INJECTION
Fault finding Tests
TEST 19
17B
WARNING:
During this operation, it is essential to:
refrain from smoking or bringing incandescent objects close to the work area,
protect yourself against fuel splashes due to residual pressure in the pipes, wear safety goggles with
side guards and waterproof gloves (Nitrile type).
IMPORTANT:
To avoid any corrosion or damage, protect the areas on which fuel is likely to run.
To prevent impurities from entering the circuit, place protective plugs on all fuel circuit components
exposed to the open air.
Remove 1 L of fuel at the fuel filter outlet (see MR 388 or 451, Mechanical, 19C, Tank, Fuel tank: Draining),
using a pneumatic transfer pump (part no. 634-200) and place it in the 1300 ml plastic cup.
Cover the plastic cup with its cover and allow it to settle for approximately 2 minutes.
Check if the fuel is cloudy or if it separates into two parts.
If the fuel is cloudy or if it separates into two parts, there is water in the fuel, the fuel is not correct.
Drain the fuel circuit, including the tank (see MR 388 or 451, Mechanical, 19C, Tank, Fuel tank: Draining).
Visually compare the fuel removed with the correct petrol.
Are the samples identical?
If the samples are identical, this means that the fuel is correct.
Otherwise, drain the fuel circuit, including the tank (see MR 388 or 451, Mechanical, 19C, Tank, Fuel tank:
Draining).
Note:
Contact the Techline if you have doubts or problems with the customer.
AFTER REPAIR
Carry out a road test, then check with the diagnostic tool.
V42_V04_TEST19 / V42_V06_TEST19
MR-453-X79-17B050$180.mif
V1
17B-194