Electrical Equipment: Lighting
Electrical Equipment: Lighting
Electrical Equipment: Lighting
LIGHTING
80D
UCH
Vdiag No.: 08, 09, 0E, 0F
V4 Edition Anglaise
"The repair procedures given by the manufacturer in this document are based on the All rights reserved by Renault s.a.s.
technical specifications current when it was prepared.
Copying or translating, in part or in full, of this document or use of the service part
The procedures may be modified as a result of changes introduced by the reference numbering system is forbidden without the prior written authority of
manufacturer in the production of the various component units and accessories from Renault s.a.s.
which his vehicles are constructed."
This document presents the fault finding procedure applicable to all computers with the following specifications:
Documentation type
Fault finding procedures (this manual):
– Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
– Visu-Schéma.
– CLIP
Diagnostic tool
Multimeter
If the information obtained by the diagnostic tool requires the electrical continuity to be checked, connect
bornier Elé. 1622 or universal bornier Elé. 1681.
WARNING:
– All checks using bornier Elé. 1622 or Elé. 1681 must be carried out with the battery disconnected.
– The bornier is only designed to be used with a multimeter. Never supply the test points with 12 V.
3. SAFETY INSTRUCTIONS
The safety instructions must be followed at all times when working on components, to avoid damage or injury:
– make sure that the battery is properly charged to avoid damaging the computers with a low charge,
– use the appropriate tools
UCH_V08_PRELI/UCH_V09_PRELI/UCH_V0E_PRELI/UCH_V0F_PRELI
MR-426-B90-80D000$010.mif
V4
80D-2
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – List and location of components
17
8 22
3
11
6
15
9 13
19
20
1
10 2 12
14
5 16
4 21
7
18
8 17
3
22
6 11
15
9 13
19 20
1
10 2
12
5
14
4 16
7 21
18
MR-426-B90-80D000$020.mif
V4
80D-3
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – List and location of components
17
8 22
3
11
6 15
13
9
1 19
20
10 2
12
5 14
4 16
7 21
18
10- front left-hand fog light 21- rear left-hand indicator light
11- rear right-hand fog light 22- rear right-hand indicator light
MR-426-B90-80D000$020.mif
V4
80D-4
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Role of components
Side lights:
The side lights are switched on directly using the lighting stalk, via the passenger compartment fuse box.
This function lights all the side lights (front and rear) as well as the number plate lighting.
Dipped headlights:
The dipped headlights are switched on directly using the lighting stalk, via the passenger compartment fuse box.
This function lights only the two bulbs providing the dipped headlights function.
Indicator lights:
The "left-hand or right-hand indicator light illumination request" signal initiated by the driver using the lighting stalk is
sent to the UCH, which controls the left-hand and right-hand indicator lights.
MR-426-B90-80D000$030.mif
V4
80D-5
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Operating diagram
645 UCH
MR-426-B90-80D000$040.mif
V4
80D-6
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Operating diagram
RPD
226
F11 (10 A) MA
R F12 (10 A)
209
1016
MB
RPG
227
9J F20 (7.5 A) 9P
209 173
1016
MG
MR-426-B90-80D000$040.mif
V4
80D-7
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Operating diagram
Side lights:
LPD
184
MA
LPD
172
MF
F19 (7.5 A)
L
209
1016
LPG
173
MG
LPG
185
MB
MR-426-B90-80D000$040.mif
V4
80D-8
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Operating diagram
Dipped headlights:
CPD
226
F10 (10 A)
CSO MA
209
1016
CPG
227
MB
MR-426-B90-80D000$040.mif
V4
80D-9
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Function
The lighting function is provided by the UCH computer. This computer is connected via a wire connection.
The UCH interprets the driver's intention via the steering column switch, then transmits the lighting requests.
These requests are controlled by the UCH.
The UCH also manages the interior lights (courtesy lights, air conditioning indicator light, central door locking
indicator light etc.).
MR-426-B90-80D000$050.mif
V4
80D-10
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Function
The LIGHTING function is divided into two sub-functions: lighting control and lighting power.
This function is managed directly, without the intervention of the UCH.
1. Lighting control
Operated by the driver
The UCH receives the driver's request via the steering column switches and the hazard warning lights button.
View the statuses of the available commands (see Status summary table).
2. Lighting power
The UCH manages the supply to the interior lighting, the heating and air conditioning system indicator lights, and the
central locking indicator lights.
The UCH manages the supply to the indicators.
The functioning of the lights supplied by the UCH can be checked using the actuator commands AC022 Left-hand
indicator, AC023 Right-hand indicator, and AC145 Front courtesy lights.
MR-426-B90-80D000$050.mif
V4
80D-11
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Configuration
Equipment required:
Configuration
Name of configuration Option Configuration
reading
AUTHORISED or
LC168 Courtesy light timer
PROHIBITED
MR-426-B90-80D000$060.mif
V4
80D-12
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Conformity check
Only perform this conformity check after a complete check with the diagnostic tool.
NOTES The values indicated in this conformity check are given as examples.
Test conditions: Engine stopped, ignition on.
Parameter or status
Function Display and Notes Fault finding
Checked or action
UCH_V08_CCONF/UCH_V09_CCONF/UCH_V0E_CCONF/UCH_V0F_CCONF
MR-426-B90-80D000$070.mif
V4
80D-13
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Status summary table
MR-426-B90-80D000$080.mif
V4
80D-14
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Interpretation of statuses
Special note:
Use Wiring Diagrams Technical Note for Logan/Sandero.
Check the presence and condition of fuses F18 (10 A) and F19 on the passenger
compartment fuse box, component code 1016 and fuse F1 on the engine fuse and
ABSENT relay box, component code 597 (see MR 388 Mechanical, 81C, Fuses, Fuses: List
and location of components).
Check the connection and condition of the UCH connector, component code 645.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A
(Renault) or Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring:
Precautions for repair), repair the connector, otherwise replace the wiring.
MR-426-B90-80D000$090.mif
V4
80D-15
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Interpretation of statuses
Special note:
Use Wiring Diagrams Technical Note for Logan/Sandero.
Check the presence and condition of the supply fuse F19 or F18 (10 A) on the
ABSENT passenger compartment fuse box, component code 1016 (see MR 388 Mechanical,
81C, Fuses, Fuses: List and location of components).
Check the connection and condition of the hazard warning lights switch connector,
component code 125.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A
(Renault) or Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring:
Precautions for repair), repair the connector, otherwise replace the wiring.
MR-426-B90-80D000$090.mif
V4
80D-16
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Interpretation of statuses
MR-426-B90-80D000$090.mif
V4
80D-17
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Interpretation of statuses
Special note:
Use Wiring Diagrams Technical Note for Logan/Sandero.
Check the presence and condition of the supply fuse F19 or F18 (10 A) on the
ABSENT passenger compartment fuse box, component code 1016 (see MR 388 Mechanical,
81C, Fuses, Fuses: List and location of components).
Check the connection and condition of the direction indicator stalk connector,
component code 209 and the UCH connector, component code 645.
If the connector(s) are faulty and if there is a repair procedure (see Technical Note
6015A (Renault) or Technical Note 9804A (Dacia), Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the operation of the direction indicator stalk in the left-hand indicator position:
Check the continuity between connections 64T and MAM.
Check the operation of the direction indicator stalk in the right-hand indicator position:
Check the continuity between connections 64S and MAM.
Disconnect the connectors of the UCH, the right-hand indicator, and the left-hand
indicator.
Check the continuity and insulation of the following connections:
• 64S between components 209 and 645,
• 64T between components 209 and 645.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note
6015A (Renault) or Technical Note 9804A (Dacia), Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
Special note:
Use Wiring Diagrams Technical Note for Logan/Sandero.
Check the presence and condition of supply fuses F9 (10A) and F10 (10A) on the
ABSENT passenger compartment fuse box, component code 1016 (see MR 388, Mechanical,
81C, Fuses, Fuses: List and location of components).
Check the connection and condition of the left-hand dipped headlight connector,
component code 227, and the right-hand dipped headlight connector, component
code 226.
If the connector(s) are faulty and if there is a repair procedure (see Technical Note
6015A (Renault) or Technical Note 9804A (Dacia), Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the connection and condition of the UCH connector, component code 645, the
lighting stalk connector, component code 209, and the engine fuse and relay box
connector, component code 597.
If the connector(s) are faulty and if there is a repair procedure (see Technical Note
6015A (Renault) or Technical Note 9804A (Dacia), Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
MR-426-B90-80D000$090.mif
V4
80D-19
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Interpretation of statuses
ET554
CONTINUED
MR-426-B90-80D000$090.mif
V4
80D-20
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Interpretation of statuses
Special note:
Use Wiring Diagrams Technical Note for Logan/Sandero.
Check the presence and condition of the supply fuse F20 (7.5 A) on the passenger
ABSENT compartment fuse box, component code 1016 (see MR 388 Mechanical, 81C, Fuses,
Fuses: List and location of components).
Check the connection and condition of the rear fog light connector, component code
173, and the lighting stalk connector, component code 209.
If the connector(s) are faulty and if there is a repair procedure (see Technical Note
6015A (Renault) or Technical Note 9804A (Dacia), Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the connection and condition of the UCH connector, component code 645.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A
(Renault) or Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring:
Precautions for repair), repair the connector, otherwise replace the wiring.
MR-426-B90-80D000$090.mif
V4
80D-21
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Interpretation of statuses
ET556
CONTINUED
MR-426-B90-80D000$090.mif
V4
80D-22
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Command summary table
MR-426-B90-80D000$100.mif
V4
80D-23
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Interpretation of commands
LEFT-HAND INDICATOR
AC022
Special note:
Use Wiring Diagrams Technical Note for Logan/Sandero.
Check the presence and condition of the supply fuse F19 or F18 (10 A) on the passenger compartment fuse box,
component code 1016 (see MR 388 Mechanical, 81C, Fuses, Fuses: List and location of components).
Check the connection and condition of the indicator control stalk connector, component code 209, and the UCH
connector, component code 645.
If the connector(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check the operation of the direction indicator stalk in the left-hand indicator position:
Check the continuity between connections 64T and MAM of component 209.
AFTER REPAIR Carry out a road test and then a check using the diagnostic tool.
UCH_V08_AC022/UCH_V09_AC022/UCH_V0E_AC022/UCH_V0F_AC022
MR-426-B90-80D000$110.mif
V4
80D-24
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Interpretation of commands
AC022
CONTINUED
AFTER REPAIR Carry out a road test and then a check using the diagnostic tool.
MR-426-B90-80D000$110.mif
V4
80D-25
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Interpretation of commands
Special note:
Use Wiring Diagrams Technical Note for Logan/Sandero.
Check the presence and condition of the supply fuse F19 or F18 (10 A) on the passenger compartment fuse box,
component code 1016 (see MR 388 Mechanical, 81C, Fuses, Fuses: List and location of components).
Check the connection and condition of the indicator control stalk connector, component code 209, and the UCH
connector, component code 645.
If the connector(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check the operation of the indicator control stalk in the right-hand indicator position:
Check the continuity between connections 64S and MAM of component 209.
AFTER REPAIR Carry out a road test and then a check using the diagnostic tool.
UCH_V08_AC023/UCH_V09_AC023/UCH_V0E_AC023/UCH_V0F_AC023
MR-426-B90-80D000$110.mif
V4
80D-26
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Interpretation of commands
AC023
CONTINUED
AFTER REPAIR Carry out a road test and then a check using the diagnostic tool.
MR-426-B90-80D000$110.mif
V4
80D-27
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Interpretation of commands
Special note:
Use Wiring Diagrams Technical Note for Logan/Sandero.
Check the connection and condition of the front courtesy light connector, component code 213, and the UCH
connector, component code 645.
If the connector(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
AFTER REPAIR Carry out a road test and then a check using the diagnostic tool.
UCH_V08_AC145/UCH_V09_AC145/UCH_V0E_AC145/UCH_V0F_AC145
MR-426-B90-80D000$110.mif
V4
80D-28
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Customer complaints
Only refer to these customer complaints after carrying out a complete check with
NOTES
the diagnostic tool
LIGHTING
MR-426-B90-80D000$120.mif
V4
80D-29
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Fault finding chart
Only consult this customer complaint after a complete check with the
diagnostic tool.
Check the bulbs.
NOTES
Special note:
Use Wiring Diagrams Technical Note for Logan/Sandero.
Check the presence and condition of the supply fuse F19 or F18 (10 A) on the passenger compartment fuse box,
component code 1016 (see MR 388 Mechanical, 81C, Fuses, Fuses: List and location of components).
Press the hazard warning lights switch and check that status ET485 Hazard warning lights signal is PRESENT;
if not, refer to the interpretation of this status.
Activate the right-hand or left-hand indicator signal and check that the ET486 Right-hand indicator signal and
ET487 Left-hand indicator signal are PRESENT; if not, refer to the interpretation of these statuses.
UCH_V08_ALP02/UCH_V09_ALP02/UCH_V0E_ALP02/UCH_V0F_ALP02
MR-426-B90-80D000$130.mif
V4
80D-30
UCH
LIGHTING
80D
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Fault finding chart
Only consult this customer complaint after a complete check with the diagnostic
tool.
Check the bulbs.
NOTES
Special note:
Use Wiring Diagrams Technical Note for Logan/Sandero.
Activate the side lights control and check that status ET484 Side lights signal is PRESENT; if not, refer to the
interpretation of this status.
Check the presence and condition of fuses F18 (10 A) and F19 on the passenger compartment fuse box,
component code 1016, and fuse F1 on the engine fuse and relay box, component code 597 (see MR 388
Mechanical, 81C, Fuses, Fuses: List and location of components).
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Check for earths on the following connections:
• MA of component 184,
• MB of component 185,
• MG of component 173,
• MF of component 172,
• MG of component 1324,
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
UCH_V08_ALP03/UCH_V09_ALP03/UCH_V0E_ALP03/UCH_V0F_ALP03
MR-426-B90-80D000$130.mif
V4
80D-31