Project Title: Potential of Ready Mixed Concrete in IHB' Sector

Page |1
Project Title: Potential of Ready mixed concrete in ‘IHB’ sector

Prepared by: Prosenjit Roy
Date: 03.05.18
1. What is the difference between cement & concrete?
Cement (sometimes referred to as Portland cement or hydraulic cement) is one component of

concrete. Cement is to concrete what flour is to a loaf of bread. Concrete is basically a mixture
of 2 components: aggregates & paste. The paste, comprised of cement & water, binds the
aggregates (sand & stone or gravel) into a rock-like mass as the paste hardens because of the
chemical reaction between cement & water. This reaction is called hydration.
2. What makes concrete crack?
Concrete 'shrinks' slightly as it hardens. A normal shrinkage rate is approximately 1/8" per 10
linear feet. This shrinkage is caused by loss of excess water from the mix. Obviously, the 'wetter'
the mix, the higher the shrinkage rate. Control joints should be placed in the concrete at
intervals equal to 2.5 times (in feet) the thickness of the slab. For example, a slab 4" thick should
have control joints every 10 feet.
3. How long does concrete continue to gain strength after it is placed?
Concrete's most rapid period of strength gain occurs in the first 7 days. The accepted time
standard for measuring concrete strength is 28 days. However, concrete will continue to gain
strength for long periods of time (months, even years) as long as moisture is present to continue
the chemical process of hydration.
4. What is the setting time of concrete?
The setting time is the time required by concrete to harden & set itself according to the
framework in which it has been placed. The amount of time taken by concrete to set is 7 to 10
hours depending on the conditions under which the concrete is placed in the framework.
But this does not mean that the framework may be removed after 7 hours. The initial setting of
concrete does not impart enough strength for it to withstand its own self load so the framework
should be removed only after 7 to 10 days of proper curing.
Page |2
5. Is the addition of fly ash in cement detrimental to its strength?
No, this is not true. In fact, the advantages of the addition of fly ash are numerous, some of
which are listed below:
Fly ash reduces the permeability of concrete thus helping in making the concrete structures
waterproof.
The addition of fly ash also helps in better bonding with the reinforcement. It also increases the
density of concrete by reducing air voids. It gives a pleasing appearance to the finished concrete.
6. Why should fresh concrete be properly cured?
The surface of freshly placed concrete should be kept moist for at least 7 days. Contrary to
popular belief, concrete should not be allowed to 'dry out.'
If the concrete is allowed to 'dry out,' the ultimate strength gain will be considerably less than its
designed strength. Proper curing will also minimize the potential of cracking. The simplest
method of moist curing is wetting the surface of the concrete & then covering it with
polyethylene.
7. What causes scaling & surface shrinkage cracks?
These defects are, generally, a result of improper finishing of the concrete. The prime factor
affecting concrete strength is water / cement ratio. If excess water is added to the surface of the
concrete during placement & finishing, the water / cement ratio on the surface may be
drastically increased. This condition greatly reduces the strength of the concrete on the surface.
Unfortunately this is where the wear takes place.
8. What effect does the water / cement ratio have on the strength of concrete?
The water cement ratio is very important with regards to the strength of the concrete. The
strength of concrete is inversely proportional to the water cement ratio, i.e. with increase in
water content the compressive strength of concrete decreases & vice versa.
9. What is the function of water in concrete?
It is with water that cement undergoes the process of hydration to form a gel with binding
property covering the aggregates uniformly on mixing. However, quantity of water for mixing
has to be limited to achieve the required consistency, as excess water is a deterrent to concrete.
Potable water can be used for the same.
Page |3
10. What does it mean to cure concrete?
Curing is one of the most important steps in quality concrete construction & one of the most
neglected. Effective curing is absolutely essential for surface durability. Fresh concrete must be
kept warm & moist until the mixing water combines chemically with the cement (hydration).
Without curing, the strength of the concrete is reduced in half. A 4000 PSI mix becomes a 2000
PSI mix at the surface with no curing. Curing is usually done by applying a coat of liquid curing
compound to the concrete as soon as it is hard enough to walk on without making marks on the
surface.

Project Title: Potential of Ready Mixed Concrete in IHB' Sector

Uploaded by

Copyright:

Available Formats

Project Title: Potential of Ready Mixed Concrete in IHB' Sector

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Project Title: Potential of Ready Mixed Concrete in IHB' Sector

Uploaded by

Copyright:

Available Formats

Page |1

Project Title: Potential of Ready mixed concrete in ‘IHB’ sector

1. What is the difference between cement & concrete?

Cement (sometimes referred to as Portland cement or hydraulic cement) is one component of

2. What makes concrete crack?

3. How long does concrete continue to gain strength after it is placed?

4. What is the setting time of concrete?

5. Is the addition of fly ash in cement detrimental to its strength?

6. Why should fresh concrete be properly cured?

7. What causes scaling & surface shrinkage cracks?

9. What is the function of water in concrete?

10. What does it mean to cure concrete?

You might also like