MINI UFO CATCHER

INSTRUCTION MANUAL
 CONTENTS OPERATE METHOD
OPERATE METHOD 2 Game Mode
Game Mode 2 1. Insert coins until the credits enough to play, demo music will turn to the game music.
2. When the lever is manipulated, time count begins and the UFO mechanism moves in the
Game Rule
2 direction in which the lever is manipulated.
3. The arm of the UFO mechanism opens automatically whenever time runs out or the DOWN
DEMO Standby 2 BUTTON has been pressed. Whenever the UFO mechanism comes in contact with
a prize or other obstacle, or when the wire is stretched to its full length, the UFO
mechanism stops descending and the arm closes.
Input Coin 2 4.If the function “catch in the air ” is set , you can fetch the prize in the air before the UFO
mechanism descend to the bottom by press DOWN BUTTON.
Machine Shake 2 5. After the arm has closed, the UFO mechanism begins to ascend. When it reaches the
upper limit sensor, the UFO mechanism moves back to home position.
Adjustment Instruction(DIP Switch) 2 6. When the UFO mechanism reaches the home position, the arm opens.
Game Rule
DIP SW1 3
DEMO Standby
DIP SW2 3 Standby music play 1 minute and stop 4 minutes when the machine is standby.
INSPECTION WAY AND NOTE ON USE 3 Insert Coin
Machine Function Test 4 -5-6 1 .Coin credit settings (credits awarded per coin) are set using DIP SW .

Fault code Statement 7 2. It will be not count if its speed faster than 20ms.

3.There will be trouble which display when insert the coin faster than 200ms.
Simple Trouble Shoot 8
4. Display of insert the coin:
CABLE DISTRIBUTION 9 *If 1 coin is worth 1 credits set, display will accumulate 1 credits when insert a coin.
* If 2 coin is worth 1 credits set, display will accumulate 1 credits when insert 2 coins.
It will make a voice and the coin counter accumulate 1 when you insert 1 coin, but
Main Board W120206 1 0-11 the display accumulate 1 credits once insert 2 coin.

Display Board W991907（Front Side） 12 Machine Shaked

Accessories 12 1.Detector is set, it will make a voice “do not shake me” when the machine is shook.
2.The UFO mechanism arm opens and back to the home position when shake is detected.

1 2
 INSPECTION WAY AND NOTE ON USE
Machine Function Test 1. DIP SW1 1 2 3 4 5 6 7 8
Way of Enter Different Test NO ON
DEMO MUSIC
Switch money channel 1 to N.C. and restart the power, [0] will display, and it means that YES OFF
test is enter. Use the lever, you can choose the test item, press the DOWN BUTTON when SECODND ON
you make sure which item to test and switch money channel 1 to N.O. then it will display [00] blinking. .SELL MODE DISPLAY TIMES OFF
Test item as follow: RANDOM MODE ON
HIT MODE
PS: Restart the power after the test FIXED MODE OFF
YES ON
FETCH IN AIR
NO OFF
BACK UP FIXED MODE OFF OFF OFF
EXHITION MODE ON
EXHITION MODE
NORMAL MODE OFF
Channel 1 Switch to N.O
FACTORY SETTING ON OFF ON OFF OFF OFF OFF OFF

* Hit Rate Mode Explain

1.Random Mode : Full strength is sent at the set time randomly, it will no longer be send whether or not win
game at the setting time.
* Adjust arm strength:：Choose 01 and press DOWM BUTTON to adjust, it will display C1,
and you can choose (C1)~(C4) by forward or backward the lever. 2.
. Fixed Mode : Win the game before full strength is sent , it should recount the hit rate.
1 Choose C1, press DOWM BUTTON, arm closes, it displays voltage value 20, move the lever left or right to adjust
the voltage value which range is 5 to 25.(C1 is the voltage value which control UFO mechanism ascend to stop.)
2 Choose C2, press DOWM BUTTON, arm closes, it displays voltage value 8, move the lever left or light to adjust
the voltage value which range is 5 to 25.(C2 is the voltage value which keep UFO mechanism stop.)
2. DIP SW 2 1 2 3 4 5 6 7 8
3 Choose C3, press DOWM BUTTON, arm closes, it displays voltage value 9, move the lever left or light to adjust
the voltage value which range is 5 to 25(C3 is the voltage value which control UFO mechanism stop to the outlet)
4 Choose C4, press DOWM BUTTON, arm closes, it displays voltage value 25, move the lever left or light to adjust BACK UP Fixed Adjustment OFF OFF OFF OFF OFF OFF OFF
the voltage value which range is 5 to 25.(C4 is the voltage value which control the full strength of the arm. )
PS:Test automatically (C1-C2-C3) once when move the lever left , test（C4) once when move the lever right.
Voltage value will display at the same time.
LETOUT Right-Back ON
* Adjust motor speed： Choose item 11, press DOWM BUTTON to adjust, it will display L0,you can choose
（L0)(FO)(UO) by forward or backward the lever:
Left-Back OFF
1.Choose L0, press DOWM BUTTON to enter the adjustment, it displays blink {0}, up and down the lever you can
adjust {0-4}, ”0” means fast, “4” means slow. Press DOWM BUTTON to finish. FACTORY SETTING OFF OFF OFF OFF OFF OFF OFF OFF
2.Choose F0, press DOWM BUTTON to enter the adjustment, it displays blink {0}, up and down the joystick you
can adjust {0-4}, ”0” means fast, “4” means slow. Press DOWM BUTTON to finish.
3.Choose U0, press DOWM BUTTON to enter the adjustment, it displays {0} blink, up and down the joystick you
can adjust {0-4}, ”0” means fast, “4” means slow. Press DOWM BUTTON to finish.

3 4
 PRIVATE TEST ITEM：

0(Normal Mode),1 (Mode 2), 2 (Sell Mode), 3 (Inspection Mode)

NO. TEST ITEM EXPLANATION
Preset：1
00 Finish Press DOWN Button To Finish Test
0. Accumulated to the hit rate, full strength will be sent, if it does
not hit, it will recount
01 Arm Strength Range:5-25 Preset：C1=20 C2=8 C3=9 C4=25
13 Game Mode Set 1 .Accumulated to the hit rate, full strength will be sent, if it
does not hit, coin must be insert if you still want to play and
full strength will be sent until you hit it. When enter the test,『a0』will display
2 .Accumulated to the hit rate, full strength will be sent until Forward the lever, 【aF】displays and the UFO mechanism go forward.
you hit it, and you do not need to insert the coin again. 02 Backward the lever,【ab】displays and the UFO mechanism go backward.

3 .Once coin is accumulated to the hit rate, you can play, UFO Right move the lever, 【ar】displays and the UFO mechanism go right.
and full strength will be sent until you hit it. And you do not
Mechanism Left move the lever, 【aL】displays and the UFO mechanism go left.
need to insert the coin again.
Press on the DOWN BUTTON and forward the lever,『bu』displays,
UFO mechanism wire is contracted

Interval Time
14 Range：0-99, 0=Never be 0, Preset：90 Press on the DOWN BUTTON and backward the lever, 『bd』displays,
UFO mechanism wire is stretched
of Sell Set
DLSPLAY
03 TEST
Seven segment display will flash in a sequence

15 Back Up (1)Adjust the switch of PCB directly, corresponding pin as follow (A). Segment
display will turn on when ON is adjusted. If pin 8 is adjusted ON, it will flash display.
(2) Units digit of display board is corresponding to DIPSW1, tens digit of display
board is corresponding to DIPSW2, as follow (B)
16 Back Up
04 DIPSW 1

6 2

（A). 5
4 3
（B).
sw2 sw1
17
Back Up
05 Music

Length of Wire 06 UFO Mechanism UFO Mechanism Test Automatically

18 Adjustment Range:1-99, Preset:32 07 COIN1 Set Preset：1 Coin worth 1 Credits
08 COIN2 Set

19 Back Up 09 Full Strength

Range：1-999（Times） Preset：10 （Set The Hit Rate）
Time Set

20 Back Up 10 Game Time Range：10-90（Times） Preset: 6

11 Motor Speed Set

0(Fast）- 4（Slow） Preset:0
21 Recover Default Value
12 Back Up

5 6
TROUBLESHOOTING FAULT CODE EXPLANATION
ITEM TROUBLE TROUBLESHOOTING FAULT CODE EXPLANATION PERIOD TROUBLESHOOTING

Coin is inserted, and it 1.Check if the game mode is 1 coin worth 1 credit, if
1 .Change U1 CPU
make the voice of accepting the setting is changed, please set the mode you want.
coin, but there is no credit Er01 CPU Fault Power On 2 .PCB Fault
on the display. 2.If it can not change, it maybe the fault of Mainboard
DIP SW
1.Check if up SW open.
1. Power On
Fault of wire
Er02
2.Check if up SW fault.
2. Game Time
Compared Mode Coin slot： contracted 3.Check if the connector bad contact.
3. Auto Test 4.Mainboard fault
1.Check if the coin you insert same as the sampling
2.Reduce the sensitivity of the coin slot。 1 .Check if up SW open.
3.Check the pin of coin slot, make sure its power supply is DC Er03 Fault of wire
stretched Auto Test
2.Check if up SW fault.
12V 3.Check if the connector bad contact.
4..Fault of the coin slot。 4.Mainboard fault
Multiple coin Mode： 1.Check the VR sensitivity. and adjust it if need.

Er04 Prize-Out
1.Sampling memory trouble, reset it according to the manual. 2.Check if J5 fall off.

2. Check the pin of coin slot, make sure its power supply is DC Fault Anytime 3 Electric eye fault
4 Mainboard fault
12V.

Forward or 1. Power On 1.Check if left SW fault

Arm will open and can’t close
again when it move to the
1.Voltage Value of the arm Vr2 is set too low. Er05 backward sw 2. Game Time 2.Check if the connector bad contact
Please set it higher fault 3. Auto Test 3.Mainboard fault
outlet after fetch a prize
1. Power On 1.Check if left SW fault

Close Once Power On 1.Coil maybe short, if so, please change it. Er06 Left sw fault 2. Game Time
3. Auto Test
2.Check if the connector bad contact
3.Mainboard fault
2.Fault of the arm strength mainboard

1.Check if the fuse melts away? Er07 Coin1 counter

fault
1.Check if the pin which insert to J5 fall off
Anytime 2.Coin Counter fault. Check if the pin fall off.
Can’t Close
2.Fault of mainboard
Er09 3.Mainboard fault

Insert the coin

1.Check if the wire of UFO mechanism
falls off Er09 faster than
When insert the
1.Coin insert fault
2.Player cheats
Can not Back to 150ms a coin
coin 3.Insert the coin faster than 150ms a coin
Home Positon 2.Fault of mainboard
Insert the coin
Er14 faster than
150ms a coin
Er14 93C66 fault Anytime 93C66 detect fault

7 8
LAYOUT EXPLANATION
1.Check if forward or backward SW of lever fault or
wiring fall off
2.Check if P.C.B,J5 of PCB insert pin looses
Lever cannot forward
MAINBOARD:W120206 and backward
3.Check if forward Sw of UFO mechanism or
backward SW fault.
MAINBOARD CONNECTOR 4. Check if motor fault or wiring fall off
5.Check if J9 of PCB inserted pin looses
W120206 I

1.Check if left or right SW of lever fault or wiring

sw1 J5 fall off
Lever cannot move left and 2.Check if P.C.B,J5 of PCB insert pin looses
sw2 CPU right 3.Check if left Sw or right SW of UFO
VOICE mechanism fault.
4.Check if motor fault or wiring fall off
1 J8 1 J7 1 J1 2 J9 24 5.Check if J9 of PCB inserted pin looses
I 23
ITEM ERROR TROUBLESHOOTING
1 W991907 Jp1 PIN1 2 W991907 Jp1 PIN2
Arm cannot down when press the
3 W991907 Jp1 PIN3 4 W991907 Jp1 PIN4 DOWN BUTTON, but it down 1.Check if DOWN BUTTON normal.
when the game is over 2.Check if the wiring fall off.
5 W991907 Jp1 PIN5 6 W991907 Jp1 PIN6
7 W991907 Jp1 PIN7 8 W991907 Jp1 PIN10 Arm cannot down when press 1 .Check if the wiring of motor fall off.
9 W991907 Jp1 PIN9 10 GND the DOWN BUTTON or close 2 .Check if Motor fault.
11 COIN1 COUNTER when descend a little, and back
12 HP 3.Check if J9 pin looses。
to home position
13 COIN2 COUTER 14 HPSW DOWN
1 . Check if the winder is taken .
15 CREDIT1 COUTER Arm cannot down
16 +12V 2 .Check if down sw easy touch or fault.
17 CREDIT2 COUTER 18 +12V 1 .Check if the wiring too short
Arm closes before it comes in
19 +12 contact with a prize, and back 2. Check if the winder is taken
20 COIN1 to its home position 3 . Check if down sw easy touch or fault.
21 +12 22 COIN2 Arm cannot open when 。
23 DOWN LIGHT+ 24 GND it move to the prize outlet 1.Check back sw or left sw fault or wiring fall off.
FETCH 2.Check if J9 of PCB insert PIN looses
25 SHAKE MACHINE 26 SENSOR
UFO mechanism back to home
27 TEST 28 +12V 1.Check if up sw wrong touch.
position after fetch the prize 2.Check if up sw fault or the wiring fall off.
29 30 GND
Arm cannot ascend, and UFO 1 . Check if Motor fault or the wiring fall off.
LEVER LEFT 32 LEVER BACKWARD 2 .Check if up sw fault or the wiring fall off.
31 mechanism cannot move after
34 LEVER UP fetch the prize 3.Mainboard fault
33 LEVER DOWN

9 10
 W120206 J1 3.96mm
DISPLAY BOARD w991907（FRONT SIDE）
GND
2 GND
3 GND J1 COLOR 2.54 PIN—MAINBOARD w120206
4 +5V
1 Brown A MAINBOARD J5 PIN1
+5V
5
6 +12V
2 Red B MAINBOARD J5 PIN2

7 +12V 3 Orange C MAINBOARD J5 PIN3

8 +12V
4 Yellow D MAINBOARD J5 PIN4
+12V
9
+24V JP1 1 5 Green E MAINBOARD J5 PIN5
10
6 Blue F MAINBOARD J5 PIN6
W120206 J8 4.22mm 7 G MAINBOARD J5 PIN7
1 Arm+ 2 X
3 Arm- 4 X 8 DP MAINBOARD J5 PIN10

5 X 6 Down Stop SW NO 9 White COM4 MAINBOARD J5 PIN9

7 X 8 Up Stop SW NO
9 X 10 Stop Left and Right NO
10 Pink COM3 GND

11 X 12 Stop Front and Back NO 11 COM2

13 GND 14 GND
15 GND 16 GND
12 COM1
17 X 18 Motor left and right -
19 X 2 0 Motor left and right +
21 Motor Front and Back +
22 Motor Front and Back -
23 Motor up and down -
2 4 Motor up and down +
ACCESSORY
W120206 J7 2.5mm Instruction Manual 1
1 VOICE VR1
2
Power Cable 1
VOICE VR1
3
4
VOICE VR1 1K VR Key 2
SP-
5 SP+

11 12