CALCULATION SHEET Rev

Subject RB6199-UTP TNB&CONSUMER SSU Project No. RB 6199

Typical Pilecap design for 1(one) Pile Group
PC1-450 Calculation No.
By KAK Chk ARR Appr SBT Date 3-Jul-17 Sheet

References:
Y
Reinforced Concrete
Designer's Handbook
10th Editon
Reynolds/Steedman
X q X Table 194, Page 421
B
p Pile Design &
Construction Practice,
L 4th Edition
Pilecap sizing Y MJ Tomlinson
Fig 7.12, Page 285
Diameter/width of pile, dia = 450 All units in kN , mm
Spacing Factor, distance between pile , k = 3 unless stated
Length of pile cap, L = 750 dia + 300
Width of pile cap, B = 750 dia + 300
Minimum depth of pile cap, Hmin = 1000 if dia < 550
Depth of pile cap used, H = 1000 H = 2xdia + 100, else
Assume maximum error in positioning pile, e = 75 H = 0.333(8xdia -600)

Reinforcement & Concrete Properties

Characteristic Strength of concrete, fcu = 30 N/mm2
Characteristic Strength of high yield reinf., fy = 460 N/mm2
Diameter of high yield reinf., dy = 16 Area = 201
Diameter of nominal high yield reinf., dn = 16 Area = 201
Bottom cover of pilecap, cb = 50
Side cover of pilecap, cs = 50
Effective depth to bottom layer, longitud, dL = 942 H - cb - dy/2
Effective depth to bottom layer, transverse, dT = 926 H - cb - dy/2 - dy

Bending Checks At Column face

Length of Stanchion, p = 250

Width of Stanchion, q = 250
Pile Working Load,Ns = 450
Pile Ultimate Load, Nult = 675 Lever Arm, La
Myy = 51 Layy=e
Mxx = 51 Laxx=e

Reinforcement Design BS8110

Longitud Direction, Cl 3.4.4
M/bd2fcu = 0.003 la = 0.95
Reinforcement area required, AsL = 129 z= 895
Provide Asmin Asmin =0.0013xBxH
Provide Bottom Longitud 05Y 16 Asmin = 975
BB @ 150 c/c Asprov= 1005
Provide Top Longitud 05Y 16 Astop= 0.0013xBxH
Transverse Direction, TT @ 150 c/c 975
M/bd2fcu = 0.003 la = 0.95
Reinforcement area required, AsT = 144 z= 880
Asmin Asmin =0.0013xLxH
Provide Bottom Transverse 05Y 16 Asmin = 975
B @ 150 c/c Asprov= 1005
Provide Top Transverse 05Y 16 Astop= 0.0013xLxH
T @ 150 c/c 975
Shear Checks
Critical Section,

For single pile cap, critical shear section directly on pile. Therefore no critical shear
section on pile cap.

Punching Shear at Perimeter of Stanchion,

For single pile cap, punching shear directly on pile. Therefore no punching shear
at perimeter of stanchion.
 CALCULATION SHEET Rev
Subject RB6199-UTP TNB&CONSUMER SSU Project No. RB 6199
Typical Pilecap design for 2(two) Pile Group
PC2-450 Calculation No.
By KAK Chk ARR Appr SBT Date 3-Jul-17 Sheet

References:
Reinforced Concrete
Y
Designer's Handbook
10th Editon
Reynolds/Steedman
X Table 194, Page 421
X B q
p
Pile Design &
Construction Practice,
k* dp
4th Edition
Pilecap sizing L MJ Tomlinson
Fig 7.12, Page 285
Y
Diameter/width of pile, dia = 450 All units in kN , mm
Spacing Factor, distance between pile , k = 3 unless stated
Length of pile cap, L = 2100 (k+1) x dia + 300
Width of pile cap, B = 750 dia + 300
Minimum depth of pile cap, Hmin = 1000 if dia < 550
Depth of pile cap used, H = 1000 H = 2xdia + 100, else
Assume maximum error in positioning pile, e = 75 H = 0.333(8xdia -600)

Reinforcement & Concrete Properties

Characteristic Strength of concrete, fcu = 30 N/mm2
Characteristic Strength of high yield reinf., fy = 460 N/mm2
Diameter of high yield reinf., dy = 16 Area = 201
Diameter of nominal high yield reinf., dn = 16 Area = 201
Bottom cover of pilecap, cb = 75
Side cover of pilecap, cs = 75
Effective depth to bottom layer, longitud, dL = 917 H - cb - dy/2
Effective depth to bottom layer, transverse, dT = 901 H - cb - dy/2 - dy

Bending Checks At Column face

Length of Stanchion, p = 250

Width of Stanchion, q = 250
Pile Working Load,Ns = 450
Pile Ultimate Load, Nult = 675 Lever Arm, La
Myy = 422 Layy=(k/2 x dia-p/2+e)
Mxx = 101 Laxx=e

Reinforcement Design BS8110

Longitud Direction, Cl 3.4.4
M/bd2fcu = 0.022 la = 0.95
Reinforcement area required, AsL = 1108 z= 871
OK Asmin =0.0013/100xBxH
Provide Bottom Longitud 06Y 16 Asmin = 975
BB @ 100 c/c Asprov= 1206
Provide Top Longitud 05Y 16 Astop= 0.0013xBxH
Transverse Direction, TT @ 150 c/c 975
M/bd2fcu = 0.002 la = 0.95
Reinforcement area required, AsT = 296 z= 856
Asmin Asmin =0.0013xLxH
Provide Bottom Transverse 14Y 16 Asmin = 2730
@ 150 c/c Asprov= 2814
Provide Top Transverse 14Y 16 Astop= 0.0013xLxH
@ 150 c/c 2730
Shear Checks
Critical Section, BS8110 Part 1
Critical Shear, vs = 0.98 N/mm2 Cl 3.11.4.3
Distance,face of stanchion to critical section, av = 490 Cl 3.11.4.4
Enhancement Factor = 3.7 Cl 3.11.4.4
Design concrete shear stress, vc = 0.38 N/mm2 Table 3.9
Modified concrete shear stress, v'c = 1.41 N/mm2
OK vc>vs
Punching Shear at Perimeter of Stanchion,
Design concrete punching shear stress, vp = 1.47 N/mm2 Cl 3.11.4.5
Allowable punching shear stress = 4.38 N/mm2
Punching shear not critical
 CALCULATION SHEET Rev
Subject RB6199-UTP TNB&CONSUMER SSU Project No. RB 6199
Typical Pilecap design for 3(three) Pile Group
PC3-450 Calculation No.
By KAK Chk ARR Appr SBT Date Sheet

T References:
Y Reinforced Concrete
Designer's Handbook
10th Editon
Reynolds/Steedman
q B X Table 194, Page 421
X
p F Pile Design &
E
Construction Practice,
4th Edition
Pilecap sizing L MJ Tomlinson
Fig 7.12, Page 285
Y
Diameter/width of pile, dia = 450 All units in kN , mm
Spacing Factor, distance between pile , k = 3 unless stated
Length of pile cap, L = 2100 (k+1) x dia + 300
Width of pile cap, B = 1920 ((6/7)k+1) x dia + 300
Height of vertical section, E = 750 dia + 250
Distance to centre of stanchion, F = 765 ((2/7)k+1/2) x dia + 150
Width of pile cap top section, T = 750 dia + 300
Minimum depth of pile cap, Hmin = 1000 if dia < 550
Depth of pile cap used, H = 1000 H = 2xdia + 100, else
Assume maximum error in positioning pile, e = 75 H = 0.333(8xdia -600)

Reinforcement & Concrete Properties

Characteristic Strength of concrete, fcu = 30 N/mm2
Characteristic Strength of high yield reinf., fy = 460 N/mm2
Diameter of high yield reinf., dy = 16 Area = 201
Diameter of nominal high yield reinf., dn = 16 Area = 201
Bottom cover of pilecap, cb = 50
Side cover of pilecap, cs = 50
Effective depth to bottom layer, longitud, dL = 942 H - cb - dy/2
Effective depth to bottom layer, transverse, dT = 926 H - cb - dy/2 - dy

Bending Checks At Column face

Length of Stanchion, p = 250

Width of Stanchion, q = 250
Pile Working Load,Ns = 450
Pile Ultimate Load, Nult = 675 Lever Arm, La
Myy = 422 Layy=(k/2 x dia-p/2+e)
Mxx = 493 Laxx=(F-(dia/2+150)-q/2+e)

Reinforcement Design BS8110

Longitud Direction, Cl 3.4.4
M/bd2fcu = 0.008 la = 0.95
Reinforcement area required, AsL = 1079 z= 895
Provide Asmin Asmin =0.0013xBxH
Provide Bottom Longitud 13Y 16 Asmin = 2496
BB @ 150 c/c Asprov= 2613
Provide Top Longitud 13Y 16 Astop= 0.0013xBxH
Transverse Direction, TT @ 150 c/c 2496
M/bd2fcu = 0.009 la = 0.95
Reinforcement area required, AsT = 1282 z= 880
Asmin Asmin =0.0013xLxH
Provide Bottom Transverse 14Y 16 Asmin = 2730
B @ 150 c/c Asprov= 2814
Provide Top Transverse 14Y 16 Astop= 0.0013xLxH
T @ 125 c/c 2730
Shear Checks
Critical Section, BS8110 Part 1
Critical Shear, vs = 0.69 N/mm2 Cl 3.11.4.3
Distance,face of stanchion to critical section, av = 205 Cl 3.11.4.4
Enhancement Factor = 9.0 Cl 3.11.4.4
Design concrete shear stress, vc = 0.34 N/mm2 Table 3.9
Modified concrete shear stress, v'c = 3.11 N/mm2
OK vc>vs
Punching Shear at Perimeter of Stanchion,
Design concrete punching shear stress, vp = 2.19 N/mm2 Cl 3.11.4.5
Allowable punching shear stress = 4.38 N/mm2
Punching shear not critical
 CALCULATION SHEET Rev
Subject RB6199-UTP TNB&CONSUMER SSU Project No. RB 6199
Typical Pilecap design for 4(four) Pile Group
PC4-450 Calculation No.
By KAK Chk ARR Appr SBT Date Sheet

References:
Reinforced Concrete
Y
Designer's Handbook
10th Editon
Reynolds/Steedman
X Table 194, Page 421
X B q k* dp

Pile Design &

p
Construction Practice,
4th Edition
Pilecap sizing L MJ Tomlinson
Fig 7.12, Page 285
Y =
Diameter/width of pile, dia 450 All units in kN , mm
Spacing Factor, distance between pile , k = 3 unless stated
Length of pile cap, L = 2100 (k+1) x dia + 300
Width of pile cap, B = 2100 (k+1) x dia + 300
Minimum depth of pile cap, Hmin = 1000 if dia < 550
Depth of pile cap used, H = 1000 H = 2xdia + 100, else
Assume maximum error in positioning pile, e = 75 H = 0.333(8xdia -600)

Reinforcement & Concrete Properties

Characteristic Strength of concrete, fcu = 30 N/mm2
Characteristic Strength of high yield reinf., fy = 460 N/mm2
Diameter of high yield reinf., dy = 16 Area = 201
Diameter of nominal high yield reinf., dn = 16 Area = 201
Bottom cover of pilecap, cb = 50
Side cover of pilecap, cs = 50
Effective depth to bottom layer, longitud, dL = 942 H - cb - dy/2
Effective depth to bottom layer, transverse, dT = 926 H - cb - dy/2 - dy

Bending Checks At Column face

Length of Stanchion, p = 250

Width of Stanchion, q = 250
Pile Working Load,Ns = 450
Pile Ultimate Load, Nult = 675 Lever Arm, La
Myy = 844 Layy=(k/2 x dia-p/2+e)
Mxx = 844 Laxx=(k/2 x dia-q/2+e)

Reinforcement Design BS8110

Longitud Direction, Cl 3.4.4
M/bd2fcu = 0.015 la = 0.95
Reinforcement area required, AsL = 2158 z= 895
Provide Asmin Asmin =0.0013xBxH
Provide Bottom Longitud 14Y 16 Asmin = 2730
BB @ 150 c/c Asprov= 2814
Provide Top Longitud 14Y 16 Astop= 0.0013xBxH
Transverse Direction, TT @ 150 c/c 2730
M/bd2fcu = 0.016 la = 0.95
Reinforcement area required, AsT = 2195 z= 880
Asmin Asmin =0.0013xLxH
Provide Bottom Transverse 14Y 16 Asmin = 2730
B @ 150 c/c Asprov= 2814
Provide Top Transverse 14Y 16 Astop= 0.0013xLxH
T @ 150 c/c 2730
Shear Checks
Critical Section, BS8110 Part 1
Critical Shear, vs = 0.68 N/mm2 Cl 3.11.4.3
Distance,face of stanchion to critical section, av = 490 Cl 3.11.4.4
Enhancement Factor = 3.8 Cl 3.11.4.4
Design concrete shear stress, vc = 0.35 N/mm2 Table 3.9
Modified concrete shear stress, v'c = 1.35 N/mm2
OK vc>vs
Punching Shear at Perimeter of Stanchion,
Design concrete punching shear stress, vp = 2.87 N/mm2 Cl 3.11.4.5
Allowable punching shear stress = 4.38 N/mm2
Punching shear not critical
 CALCULATION SHEET Rev
Subject RB6199-UTP TNB&CONSUMER SSU Project No. RB 6199
Typical Pilecap design for 5(five) Pile Group
PC5-450 Calculation No.
By KAK Chk ARR Appr SBT Date Sheet

References:
Reinforced Concrete
Y
Designer's Handbook
10th Editon
Reynolds/Steedman
X Table 194, Page 421
X B q 1.414k* dp

Pile Design &

p
Construction Practice,
4th Edition
Pilecap sizing L MJ Tomlinson
Fig 7.12, Page 285
Y =
Diameter/width of pile, dia 450 All units in kN , mm
Spacing Factor, distance between pile , k = 3 unless stated
Length of pile cap, L = 2659 (1.414k+1) x dia + 300
Width of pile cap, B = 2659 (1.414k+1) x dia + 300
Minimum depth of pile cap, Hmin = 1000 if dia < 550
Depth of pile cap used, H = 1100 H = 2xdia + 100, else
Assume maximum error in positioning pile, e = 75 H = 0.333(8xdia -600)

Reinforcement & Concrete Properties

Characteristic Strength of concrete, fcu = 30 N/mm2
Characteristic Strength of high yield reinf., fy = 460 N/mm2
Diameter of high yield reinf., dy = 16 Area = 201
Diameter of nominal high yield reinf., dn = 16 Area = 201
Bottom cover of pilecap, cb = 50
Side cover of pilecap, cs = 50
Effective depth to bottom layer, longitud, dL = 1042 H - cb - dy/2
Effective depth to bottom layer, transverse, dT = 1026 H - cb - dy/2 - dy

Bending Checks At Column face

Length of Stanchion, p = 250

Width of Stanchion, q = 250
Pile Working Load,Ns = 450
Pile Ultimate Load, Nult = 675 Lever Arm, La
Myy = 1221 Layy=(1.414k/2 x dia-p/2+e)
Mxx = 1221 Laxx=(1.414k/2 x dia-q/2+e)

Reinforcement Design BS8110

Longitud Direction, Cl 3.4.4
M/bd2fcu = 0.014 la = 0.95
Reinforcement area required, AsL = 2823 z= 990
Provide Asmin Asmin =0.0013xBxH
Provide Bottom Longitud 19Y 16 Asmin = 3802
BB @ 125 c/c Asprov= 3819
Provide Top Longitud 19Y 16 Astop= 0.0013xBxH
Transverse Direction, TT @ 125 c/c 3802
M/bd2fcu = 0.015 la = 0.95
Reinforcement area required, AsT = 2867 z= 975
Asmin Asmin =0.0013xLxH
Provide Bottom Transverse 19Y 16 Asmin = 3802
B @ 125 c/c Asprov= 3819
Provide Top Transverse 19Y 16 Astop= 0.0013xLxH
T @ 125 c/c 3802
Shear Checks
Critical Section, BS8110 Part 1
Critical Shear, vs = 0.49 N/mm2 Cl 3.11.4.3
Distance,face of stanchion to critical section, av = 770 Cl 3.11.4.4
Enhancement Factor = 2.71 Cl 3.11.4.4
Design concrete shear stress, vc = 0.35 N/mm2 Table 3.9
Modified concrete shear stress, v'c = 0.94 N/mm2
OK vc>vs
Punching Shear at Perimeter of Stanchion,
Design concrete punching shear stress, vp = 3.24 N/mm2 Cl 3.11.4.5
Allowable punching shear stress = 4.38 N/mm2
Punching shear not critical
 CALCULATION SHEET Rev
Subject RB6199-UTP TNB&CONSUMER SSU Project No. RB 6199
Typical Pilecap Design of 6(six) Pile Group
PC6-450 Calculation No.
By KAK Chk ARR Appr SBT Date 3-Jul-17 Sheet

References:
Reinforced Concrete
Y Designer's Handbook
10th Editon
Reynolds/Steedman
X B p q k* dp X Table 194, Page 421

Pile Design &

Construction Practice,
L
4th Edition
Pilecap sizing Y MJ Tomlinson
Fig 7.12, Page 285
Diameter/width of pile, dia = 450 All units in kN , mm
Spacing Factor, distance between pile , k = 3 unless stated
Length of pile cap, L = 3450 (2k+1) x dia + 300
Width of pile cap, B = 2100 (k+1) x dia + 300
Minimum depth of pile cap, Hmin = 1000 if dia < 550
Depth of pile cap used, H = 1200 H = 2xdia + 100, else
Assume maximum error in positioning pile, e = 75 H = 0.333(8xdia -600)

Reinforcement & Concrete Properties

Characteristic Strength of concrete, fcu = 30 N/mm2
Characteristic Strength of high yield reinf., fy = 460 N/mm2
Diameter of high yield reinf., dy = 20 Area = 314
Diameter of nominal high yield reinf., dn = 16 Area = 201
Bottom cover of pilecap, cb = 50
Side cover of pilecap, cs = 50
Effective depth to bottom layer, longitud, dL = 1140 H - cb - dy/2
Effective depth to bottom layer, transverse, dT = 1120 H - cb - dy/2 - dy

Bending Checks At Column face

Length of Stanchion, p = 250

Width of Stanchion, q = 250
Pile Working Load,Ns = 450
Pile Ultimate Load, Nult = 675 Lever Arm, La
Myy = 1755 Layy=(k x dia-p/2+e)
Mxx = 1266 Laxx=((k x dia)/2-p/2+e)

Reinforcement Design BS8110 Part 1

Longitud Direction, Cl 3.4.4
M/bd2fcu = 0.021 la = 0.95
Reinforcement area required, AsL = 4049 z= 1083
OK Asmin =0.0013xBxH
Provide Bottom Longitud 13Y 20 Asmin = 3276
BB @ 125 c/c Asprov= 4082
Provide Top Longitud 17Y 16 Astop= 0.0013xBxH
Transverse Direction, TT @ 100 c/c 3276
M/bd2fcu = 0.010 la = 0.95
Reinforcement area required, AsT = 2972 z= 1064
Asmin Asmin =0.0013xLxH
Provide Bottom Transverse 18Y 20 Asmin = 5382
B @ 175 c/c Asprov= 5652
Provide Top Transverse 27Y 16 Astop= 0.0013xLxH
T @ 100 c/c 5382
Shear Checks
Critical Section, BS8110 Part 1
Critical Shear, vs = 0.56 N/mm2 Cl 3.11.4.3
Distance,face of stanchion to critical section, av = 1165 Cl 3.11.4.4
Enhancement Factor = 1.96 Cl 3.11.4.4
Design concrete shear stress, vc = 0.37 N/mm2 Table 3.9
Modified concrete shear stress, v'c = 0.73 N/mm2
OK vc>vs
Punching Shear at Perimeter of Stanchion,
Design concrete punching shear stress, vp = 3.55 N/mm2 Cl 3.11.4.5
Allowable punching shear stress = 4.38 N/mm2
Punching shear not critical
 CALCULATION SHEET Rev
Subject RB6199-UTP TNB&CONSUMER SSU Project No. RB 6199
Typical Pilecap Design of 7(seven) Pile Group
PC7-450 Calculation No.
By KAK Chk ARR Appr SBT Date 3-Jul-17 Sheet

References:
Y
Reinforced Concrete
Designer's Handbook
10th Editon
Reynolds/Steedman
X B q X Table 194, Page 421

p
Pile Design &
Construction Practice,
k* dp
4th Edition
Pilecap sizing L Y MJ Tomlinson
Fig 7.12, Page 285
Diameter/width of pile, dia = 450 All units in kN , mm
Spacing Factor, distance between pile , k = 3 unless stated
Length of pile cap, L = 3500 (2k+1) x dia + 300
Width of pile cap, B = 3100 (k+1) x dia + 300
Minimum depth of pile cap, Hmin = 1000 if dia < 550
Depth of pile cap used, H = 1300 H = 2xdia + 100, else
Assume maximum error in positioning pile, e = 75 H = 0.333(8xdia -600)

Reinforcement & Concrete Properties

Characteristic Strength of concrete, fcu = 30 N/mm2
Characteristic Strength of high yield reinf., fy = 460 N/mm2
Diameter of high yield reinf., dy = 20 Area = 314
Diameter of nominal high yield reinf., dn = 16 Area = 201
Bottom cover of pilecap, cb = 50
Side cover of pilecap, cs = 50
Effective depth to bottom layer, longitud, dL = 1240 H - cb - dy/2
Effective depth to bottom layer, transverse, dT = 1220 H - cb - dy/2 - dy

Bending Checks At Column face

Length of Stanchion, p = 250

Width of Stanchion, q = 250
Pile Ultimate Load, Nult = 675 Lever Arm, La
Myy = 1721 Layy=(k x dia-p/2+e)
Mxx = 1511 Laxx=((k x dia)/2-p/2+e)

Reinforcement Design BS8110 Part 1

Longitud Direction, Cl 3.4.4
M/bd2fcu = 0.012 la = 0.95
Reinforcement area required, AsL = 3344 z= 1178
Provide Asmin Asmin =0.0013xBxH
Provide Bottom Longitud 17Y 20 Asmin = 5239
BB @ 150 c/c Asprov= 5338
Provide Top Longitud 27Y 16 Astop= 0.0013xBxH
Transverse Direction, TT @ 100 c/c 5239
M/bd2fcu = 0.010 la = 0.95
Reinforcement area required, AsT = 2983 z= 1159
Asmin Asmin =0.0013xLxH
Provide Bottom Transverse 19Y 20 Asmin = 5915
B @ 150 c/c Asprov= 5966
Provide Top Transverse 30Y 16 Astop= 0.0013xLxH
T @ 100 c/c 5915
Shear Checks
Critical Section, BS8110 Part 1
Critical Shear, vs = 0.53 N/mm2 Cl 3.11.4.3
Distance,face of stanchion to critical section, av = 490 Cl 3.11.4.4
Enhancement Factor = 5.06 Cl 3.11.4.4
Design concrete shear stress, vc = 0.33 N/mm2 Table 3.9
Modified concrete shear stress, v'c = 1.66 N/mm2
OK vc>vs
Punching Shear at Perimeter of Stanchion,
Design concrete punching shear stress, vp = 3.81 N/mm2 Cl 3.11.4.5
Allowable punching shear stress = 4.38 N/mm2
Punching Shear not critical
 CALCULATION SHEET
Subject RB6199-UTP TNB&CONSUMER SSU
Typical Pilecap Design of 8(Eight) Pile Group
PC8-450
By KAK Chk ARR Appr SBT Date 3-Jul-17

X k* dp X
B
q
p

L
Pilecap sizing Y

Diameter/width of pile, dia = 450

Spacing Factor, distance between pile , k = 3
Length of pile cap, L = 4568
Width of pile cap, B = 2659
Minimum depth of pile cap, Hmin = 1000
Depth of pile cap used, H = 1400
Assume maximum error in positioning pile, e = 75
Reinforcement & Concrete Properties
Characteristic Strength of concrete, fcu = 30 N/mm2
Characteristic Strength of high yield reinf., fy = 460 N/mm2
Diameter of high yield reinf., dy = 25
Diameter of nominal high yield reinf., dn = 25
Bottom cover of pilecap, cb = 50
Side cover of pilecap, cs = 50
Effective depth to bottom layer, longitud, dL = 1338
Effective depth to bottom layer, transverse, dT = 1313
Bending Checks
Length of Stanchion, p = 250
Width of Stanchion, q = 250
Pile Ultimate Load, Nult = 675
Myy = 3121
Mxx = 1832
Reinforcement Design
Longitud Direction,
M/bd2fcu = 0.022
Reinforcement area required, AsL = 5620
OK
Provide Bottom Longitud 12Y 25
@ 175 c/c
Provide Top Longitud 10Y 25
Transverse Direction, @ 225 c/c
M/bd2fcu = 0.008
Reinforcement area required, AsT = 3362
Asmin
Provide Bottom Transverse 17Y 25
@ 225 c/c
Provide Top Transverse 17Y 25
@ 225 c/c
Shear Checks
Critical Section,
Critical Shear, vs = 0.57 N/mm2
Distance,face of stanchion to critical section, av = 770
Enhancement Factor = 3.48
Design concrete shear stress, vc = 0.37 N/mm2
Modified concrete shear stress, v'c = 1.28 N/mm2
OK vc>vs
Punching Shear at Perimeter of Stanchion,
Design concrete punching shear stress, vp = 4.04 N/mm2
Allowable punching shear stress = 4.38 N/mm2
Punching shear not critical
Rev
Project No. RB 6199

Calculation No.
Sheet

References:
Reinforced Concrete
Designer's Handbook
10th Editon
Reynolds/Steedman
Table 194, Page 421

Pile Design &

Construction Practice,
4th Edition
MJ Tomlinson
Fig 7.12, Page 285
All units in kN , mm
unless stated
(2k+1) x dia + 600
(k+1) x dia + 600
if dia < 550
H = 2xdia + 100, else
H = 0.333(8xdia -600)

Area = 491
Area = 491

H - cb - dy/2
H - cb - dy/2 - dy

At Column face

2509.904

Lever Arm, La
Layy=(k x dia-p/2+e)
Laxx=((k x dia)/2-p/2+e)

BS8110 Part 1
Cl 3.4.4
la = 0.95
z= 1271
Asmin =0.0013xBxH 12.0
Asmin = 4840
Asprov= 5892
Astop= 0.0013xBxH
4840
la = 0.95
z= 1247
Asmin =0.0013xLxH 17.0
Asmin = 8314
Asprov= 8347
Astop= 0.0013xLxH
8314

BS8110 Part 1
Cl 3.11.4.3
Cl 3.11.4.4
Cl 3.11.4.4
Table 3.9 1

Cl 3.11.4.5
120 - SAILING SPORT TAINING CETRE OF EXCELLENT
400by400 col size
250by250 RC PILE Capacity 560 kN
H= 300 600

PC1 PC2
pilecap 2.18 10.3
soil wt 2.71 10.55
COLUMN LOAD COLUMN LOAD COLUMN LOAD
NO. COLUMN COLUMN (DL) (LL) Design load Foundation type Design load
GRID MARK (TOTAL) PC1 (TOTAL)
(kN) (kN)

1 3E 435 12 452 can use PC1

2 1E 320 75 400 can use PC1
3 3aB 242 25 272 can use PC1
4 4B 275 132 412 can use PC1
5 4E 400 145 550 can use PC1
6 4Eb 195 75 275 can use PC1
7 5Aa 150 30 185 can use PC1
8 5A 220 100 325 can use PC1
9 5D 425 115 545 can use PC1
10 5E 280 45 330 can use PC1
11 5Ea 270 125 400 can use PC1
12 5Eb 210 75 290 can use PC1
13 6Aa 180 40 225 can use PC1
14 6A 345 137 487 can use PC1
15 6Ea 270 125 400 can use PC1
16 6Eb 210 75 290 can use PC1
17 7Aa 180 40 225 can use PC1
18 7A 345 137 487 can use PC1
19 7Ea 270 125 400 can use PC1
20 7Eb 210 75 290 can use PC1
21 8Aa 150 30 185 can use PC1
22 8A 220 100 325 can use PC1
23 8E 280 45 330 can use PC1
24 8Ea 270 125 400 can use PC1
25 8Eb 210 75 290 can use PC1
26 9B 275 132 412 can use PC1
27 9E 400 145 550 can use PC1
28 9Eb 195 75 275 can use PC1
29 12C 300 75 380 can use PC1
30 12E 300 75 380 can use PC1
1 140 80 225 can use PC1
2 140 80 225 can use PC1
3 140 80 225 can use PC1
4 140 80 225 can use PC1
5 140 80 225 can use PC1
6 140 80 225 can use PC1
7 140 80 225 can use PC1
8 140 80 225 can use PC1
9 140 80 225 can use PC1
10 140 80 225 can use PC1
11 140 80 225 can use PC1
12 140 80 225 can use PC1
Foundation type
PC2