Index

2 Opening Instructions & Keyboard disassembling

3 RP100-150 Initial Check, Autotest Procedure, Updating Procedure
4 RP200 Initial Check, Autotest Procedure, Updating Procedure
6 RP100-150 Block Diagram
7 RP200 Block Diagram
8 RP100 - Power Amplifier & Supply, Pedals, Phones, Outputs Boards
9 RP150 - Power Amplifier & Supply, Pedals, Phones, Outputs Boards
10 RP200 - Power Amplifier & Supply, Pedals, Mixer & Phones Aplifier, Phones, Outputs Boards
11 Keyboard Interface & Contacts Boards
12 RP100-150 Controls Panel & Display Boards
13 RP200 Controls Panel & Display Boards
14 RP100-150 Cpu & Sound Generator Board
15 Timing Table & 310603 Board Layout
16 RP200 Cpu & Sound Generator Board Part 1 of 2
17 RP200 Cpu & Sound Generator Board Part 2 of 2
18 RP100 and RP150 Spare Part List
19 RP200 Spare Part List

Warnings
Notice
 Service must be carried out by qualified personnel only.Any tampering carried out by unqualified personnel during the guarantee period
will forfeit the right to guarantee.
 For a correct operation of the instrument, after having switched off, be careful to wait at least 3 seconds before switching on again.
 To improve the device's specifications, the schematic diagrams may be subject to change without prior notice.
All components marked by this symbol have special safety characteristics, when replacing any of these components use only
manufacturer's specified parts.

SERVICE MANUAL
 The (µ) micro symbol of capacitance value is substituted by U.
 The (Ω) omega symbol of resistance value is substituted by E.
 The electrolytic capacitors are 25Vdc rated voltage unless otherwise specified.
 All resistors are 1/8Ω unless otherwise specified.
 All switches shown in the "OFF" position. All DC voltages measured to ground with a voltmeter 20KOhm/V.

 Soldering point. Supply voltage. Logic supply ground.

 Male connector. Test point. Analog supply ground.
 Female connector. Flag joined with one or more flags Chassis ground.
 M/F faston connector. with the same signal name inscribed. Earth ground.

ATTENTION
Observe precautions when handling electrostatic sensitive devices.

Address
L CODE: 270212M 

GENERALMUSIC S.p.A. Sales Division: 47842 S.Giovanni in Marignano (RN) ITALY - Via delle Rose, 12 - tel. 0541/959511 - fax 0541/957404
GENERALMUSIC on the NET: http://www.generalmusic.com

1J

Downloaded from www.Manualslib.com manuals search engine

 1) TO REMOVE THE COVER UNSCREW THE 4 SCREWS ON THE REAR, PULL THE COVER TOWARDS YOU AND LIFT IT UP. 2) TO REMOVE THE CONTROL PANEL UNSCREW THE SCREWS AT EACH END AND THE SCREWS THAT ANCHOR 3) TO REMOVE THE KEYBOARD TP21 UNSCREW THE 11 SCREWS UNDER THE KEYBOARD.
THE CONTROL PANEL SUPPORTS TO THE CHASSIS.

RP100 RP100 RP100

4) TO REMOVE A KEY INSERT A SCREWDRIVER OR OTHER SIMILAR OBJECT IN THE SPLIT AT THE KEY BACK, APPLY A LIGHT PRESSURE AND PUSH IN THE DIRECTION SHOWN.

NOTE: BEFORE YOU REMOVE A NATURAL KEY YOU MUST REMOVE THE KEYBOARD, IF YOU REMOVE A SHARP KEY THIS OPERATION IS NOT NECESSARY 1) TO REMOVE THE COVER UNSCREW THE 4 SCREWS ON THE REAR, PULL THE COVER TOWARDS YOU AND LIFT IT UP.

RP150
RP200

TP21

REMOVE THE KEY RETURN SPRING.

UNLOCK THE KEY APPLING NOT MUCH STRENGTH.
NOTE: TO REMOVE A SHARP KEY BEFORE YOU MUST REMOVE THE NEAR NATURAL KEYS.

TP10

DRWG. BOCCATO DWG#500870 PCB# GENERALMUSIC S.p.A. ITALY

CKD DISK: PART:
1/1 RP-100-150-200 ALL RIGHTS ARE RESERVED, NO COPIES
Opening Instructions OR REPRODUCE THIS DOCUMENT WITHOUT
APP. REV:26/07/99 WRITTEN CONSENT BY GENERALMUSIC.
& Keyboard disassembling

J2

Downloaded from www.Manualslib.com manuals search engine

 RP100-150 INITIAL CHECK Re-set the frequency at 1KHz and check HEADPHONES and AUX outputs with the
oscilloscope inserting a stereo jack in the left phones socket (speakers will go be
Operation Descriptions Display silent) and two mono jack in the AUX OUT sockets and set volume to its maximum.
The procedures that follow must be executed subsequently in the order specified. Now verify the following level of signals:
Phones output without load = 17±1.7Vpp
Before turn on the instrument check the jumpers setting on CPU & SOUND | * REALPIANO * |
AUX output = 1.35±0.14Vpp
GENERATOR BOARD corresponds at the model accordingly to the following table: | RP100 |
Set the VOLUME to minimum.
MODEL J4 J5 J3 J6 J2 | * BALDWIN * | Apply a sinusoidal signal of 0.730Vpp at 1KHz with a generator to the AUX IN left and
RP100 GEM 1-2 1-2 1-2 1-2 1-2 |PIANOVELLE RP100|
RP100 BALDWIN 1-2 1-2 1-2 1-2 2-3 right sockets and verify the signal output:
RP150 GEM 1-2 1-2 1-2 2-3 1-2 AUX output = 1.35±0.07Vpp
| * REALPIANO * |
RP150 BALDWIN 1-2 1-2 1-2 2-3 2-3 |TEST END: SWITCH|
| RP150 | Autotest is over, turn off the instrument.
RP90 GEM 1-2 1-2 2-3 1-2 1-2 ** v.2.00 or greater |POWER TO RESTART|
RP90 BALDWIN 1-2 1-2 2-3 1-2 2-3 ** v.2.00 or greater | * BALDWIN * | RP100-150 O.S. UPDATING PROCEDURE up to ver. 2.00 with Updating Software Board (751180)
Remove the secondary fuses F1, F2, F3, located on POWER AMPLIFIER & SUPPLY |PIANOVELLE RP150|
BOARD; turn on the instrument and verify the supply AC voltages: Operation Descriptions Display
| * REALPIANO * | Start with the instrument in AUTOTEST mode as described above and press GRAND | mmm dd yyyy |
(CN5) between pin1 and pin3 = 10±0,5Vac
| RP90 | PIANO 2 times until the display shows the software version loaded in flash memory. |hh:mm:ss V #.##|
(CN9) between pin1 and pin2 = 16±0,8Vac
(CN9) between pin1 and pin3 = 16±0,8Vac |EPROM to FLASH |
| * BALDWIN * | Press GRAND PIANO to skip this procedure.
(CN9) between pin2 and pin3 = 32±1,6Vac |push REC to prog|
|PIANOVELLE RP90 |
|Wait * |
Turn off the instrument, and put the fuses back on its holders. |Eprom Checksum |
The instrument performs the flash memory data checksum and display it in
Turn on the instrument and the appropriate welcome message appears on the display.
hexadecimal value. |cks BT PR ALL|
A few seconds later the led GRAND PIANO light.
| #### #### ####|
Check the supply DC voltages on CPU & SOUND GENERATOR BOARD:
|INTERNAL PRESET| Compare the software version and checksum with the value imprinted onto the
(CN8) between pin9 and pin7 = +5±0,25Vdc
| GRAND PIANO | EPROM, if one of these does not match, the system must be upgraded, proceed to the
(CN8) between pin1 and pin4 = +12±0,6Vdc
next step.
(CN8) between pin1 and pin5 = -12±0,6Vdc
Turn off the instrument.
RP100-150 AUTOTEST PROCEDURE Insert the EPROM BOARD (where the operating system is stored) in the CN3
connector located on CPU & SOUND GENERATOR BOARD.
Operation Descriptions Display
Start with the instrument in AUTOTEST mode as described above and press GRAND
The instrument starts in AUTOTEST mode turning on the instrument while pressing PIANO 3 times.
down the "GRAND PIANO" button (pressing PRESET instead GRAND PIANO the |EPROM to FLASH |
procedure starts from LCD display test).
| RP98 | When the display shows this message press REC.
| AUTOTEST | |push REC to prog|
NOTE: Each time you press the "GRAND PIANO" button the autotest procedure The instrument erases the previous data in flash memory. After which the instrument |EPROM to FLASH |
proceeds to the next step. |erasing |
displays the amount of memory programming and finally the operation successful. If
|CONTRAST = # | the programming fails check the EPROM BOARD connection and repeat this procedure
Set the default display contrast in the ±6 range by pressing the DATA + or - buttons. |EPROM to FLASH |
| | from start. |prog: 1024/1024K|
The instrument show the date, time and release version of the software loaded in | mmm dd yyyy | |Wait * |
flash memory. |hh:mm:ss V #.##| The instrument performs the eprom memory data checksum and displays it in |Eprom Checksum |
The instrument asks if you want to update it, press GRAND PIANO to skip, the |EPROM to FLASH | hexadecimal value, compare this value with the value imprinted onto the EPROM: if it
appropriate procedure to update the software is explained further. |push REC to prog| matches the EPROM is good. |cks BT PR ALL|
|Wait * | | #### #### ####|
The instrument performs the flash memory data checksum and display it in
|Eprom Checksum | Turn off the instrument and disconnect the EPROM BOARD.
hexadecimal value.
Start with the instrument in AUTOTEST mode as described above and press GRAND
NOTE: the BT (boot) value must be 95C4 for ver.2.00, if it does not correspond you |cks BT PR ALL| | mmm dd yyyy |
PIANO 2 times until the display show the new software version loaded in flash
can not update software thru serial port but only with Update Software Board. | #### #### ####| |hh:mm:ss V #.##|
memory.
|RAM MEMORY CHECK|
The instrument performs the RAM memory test showing the address checked. |EPROM to FLASH |
|addr 23BFFF OK| Press GRAND PIANO to skip this procedure.
|push REC to prog|
|❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚|
The LCD display test shows two rows of sixteen dark spaces. |Wait * |
|❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚| The instrument performs the flash memory data checksum and displays it in |Eprom Checksum |
|--- LED TEST ---| hexadecimal value, compare this value with the value imprinted onto the EPROM: if it
Check that all leds are lighting.
|Are all leds on?|
matches the procedure has been executed succesfully. |cks BT PR ALL|
Check the VOLUMES ranges from 0 to 127. | #### #### ####|
Check all buttons (except GRAND PIANO) pressing their one at a time and checking The procedure proceed as described in AUTOTEST section, if you do not want to check
| |Button test |
that corresponding led lights, pressing PAGE UP and DOWN buttons the display shows | |Vol:0 12345 | the rest of the instrument simply turn off it.
"U" and "D", pressing DATA + and - buttons the display shows "+" and "-", pressing
RP100-150 O.S. UPDATING PROCEDURE from Serial Port (COMPUTER) ver. 2.xx or greater
BALANCE < and > buttons the display shows an "X" in 1 and 2 digits, pressing |U|Button test +|
TOUCH, STORE and REC/CONTROL buttons the display shows an "X" in 3, 4 and 5 |D|Vol:127 XXXXX-| Operation Descriptions Display
digits respectively. NOTE: This procedure is valid only if the software version installed on the piano is the
2.00 or greater.
Check the SOFT and SUSTAIN pedals, pressing each one the value change from 0
Some additional tips and advices are included in the Flashblaster Firmware Update
(released) to 127 (pressed), for RP100 the DAMPER pedal operation is similar, for |Soft Sust Damp|
Disk. The disk containing the Fblaster program can also be downloaded by internet at
RP150 the DAMPER pedal varying its value continuosly from 0 (released) to nearly | 0 0 0|
generalmusic web site (www.generalmusic.com) or required at
127 (pressed).
support@generalmusic.com
|TEST MIDI IN/OUT|
Check the MIDI I/O connecting the MIDI OUT and MIDI IN sockets by a MIDI cable. Connect the serial cable between the COMPUTER of the piano and the RS232 COM
|LOOP DETECTED OK|
Check COMPUTER I/O shorting pin 3 and pin 5 on the COMPUTER socket, check with |TST COMPUTER I/O| port of the computer (PC-Ibm or compatible).
the oscilloscope a 4Vpp (1Mhz) signal on pin 1, set volume to half stroke. |LOOP DETECTED OK| Insert the disk in the drive A (or whatever your 3.5" drive is assigned to), open the
The instrument generates a 1KHz sinusoidal signal in both audio channels. VOLUME contents of drive A and double click on the fblaster.exe file.
| SINUS. SWEEP |
fader controls the amplitude of signal and TRANSPOSE b and # buttons controls the From the OPTIONS/SETTINGS menu, make sure that the TEST AND PROGRAM choice
|Freq. 1000 Hz|
frequency from 10Hz to 2756Hz. is selected. This is very important.

3J

Downloaded from www.Manualslib.com manuals search engine

 RP200 INITIAL CHECK
|READY TO UPDATE |
Turn on the piano, while holding down the REC button until the display shows:
| | Operation Descriptions Display
Click with the mouse on the GO! button or, from the ACTION menu, select EXECUTE |TESTING... | The procedures that follow must be executed subsequently in the order specified.
(ALT+A, E). The piano display appears as follows: |n1/n2 PACKETS |
Before turn on the instrument check the jumpers setting on CPU & SOUND
| TEST OK | GENERATOR BOARD corresponds at the model accordingly to the following table:
At the end of the test the following display appears:
| | | RP200 |
|ERASING... | | REALPIANO |
After a short time, the following display appears: MODEL J4 J5 J3 J6 J2
| | | GEM |
You are now erasing the old operating system from FLASH memory. When the system RP200 GEM 1-2 1-2 1-2 1-2 1-2
|UPDATING... | RP200 BALDWIN 1-2 1-2 1-2 1-2 2-3
is erased, the following display appears as your new operating system is installed into | PIANOVELLE |
|n1/n2 PACKETS | GRP300 GEM 1-2 1-2 1-2 2-3 1-2 ** v.2.00 or greater
Flash Memory: | RP200 |
|UPDATE_OK:SWITCH| GRP300 BALDWIN 1-2 1-2 1-2 2-3 2-3 ** v.2.00 or greater | BALDWIN |
When the entire update procedure is completed, the following display appears:
|POWER TO RESTART|
The update has now been successfully completed. Turn off the power switch on the | GRP300 |
Remove the secondary fuses F1, F2, F3, located on POWER AMPLIFIER & SUPPLY | REALPIANO |
piano, and turn it back on again to use your updated instrument.
BOARD; turn on the instrument and verify the supply AC voltages: | GEM |
RP100-150 Some Repairing Tips (CN6) between pin1 and pin2 = 27,5±1,5Vac
(CN6) between pin1 and pin3 = 27,5±1,5Vac | PIANOVELLE |
Operation Descriptions Display (CN6) between pin2 and pin3 = 55±3Vac | GRP300 |
This message could be appear if an error occur on the communication channel. (CN12) between pin1 and pin2 = 16±0,8Vac | BALDWIN |
Possible solutions: (CN12) between pin1 and pin3 = 16±0,8Vac
|MIDI SCI error |
1) inconsistent data received on MIDI or COMPUTER input socket, check the ratings of (CN12) between pin2 and pin3 = 32±1,6Vac
| |
the device connected to the piano. Turn off the instrument, and put the fuses back on its holders.
2) if the error persist, try to replace Outputs Board first and CPU board second.
Turn on the instrument and the appropriate welcome message appears on the display.
This message could be appear if an error occur on the communication channel. A few seconds later the led GRAND PIANO light.
Possible solutions: Check the supply DC voltages on CPU & SOUND GENERATOR BOARD:
|VALIS SCI error | |INTERNAL PRESET|
1) verify all the connections between Keyboard Interface Board and the CPU board. (CN8) between pin9 and pin7 = +5±0,25Vdc | GRAND PIANO |
| |
2) if the error persist, try to replace Keyboard Interface Board first and CPU board (CN8) between pin1 and pin4 = +12±0,6Vdc |GR.PIANO sel.:1|
second. (CN8) between pin1 and pin5 = -12±0,6Vdc
This message could be appear if an error occur on the communication between CPU
and DISP3 chips. RP200 AUTOTEST PROCEDURE
Possible solutions: Operation Descriptions Display
|Disp Failure |
1) verify all the tracks, solders and components between CPU and DISP3 chips as
| | The instrument starts in AUTOTEST mode turning on the instrument while pressing
shown in schematics.
down the "GRAND PIANO" button (pressing PRESET instead GRAND PIANO the | RP98 |
2) if the error persist, replace the CPU board and send back to generalmusic the failed
procedure starts from LCD display test). | AUTOTEST |
CPU board.
NOTE: Each time you press the "GRAND PIANO" button the autotest procedure | |
proceeds to the next step.
|CONTRAST = # |
Set the default display contrast in the ±6 range by pressing the DATA + or - buttons. | |
| |
| mmm dd yyyy |
The instrument shows the date, time and release version of the software loaded in
|hh:mm:ss V #.##|
flash memory. | |
|EPROM to FLASH |
The instrument asks if you want to update it, press GRAND PIANO to skip, the
|push REC to prog|
appropriate procedure to update the software is explained further. | |
|Wait * |
The instrument performs the flash memory data checksum and display it in |Eprom Checksum |
hexadecimal value. | |
NOTE: the BT (boot) value must be EAAB for ver.2.00, if it does not correspond you
can not update software thru serial port but only with Update Software Board see |cks BT PR ALL|
more further. | #### #### ####|
| |
|Wait * |
|Library Checksum|
| |
The instrument performs the "LIBRARY" Rom memory data checksum and display it in
hexadecimal value. |Wait ok! |
|Checksum: A021|
| |
|RAM MEMORY CHECK|
The instrument performs the RAM memory test showing the address checked. |addr 23BFFF OK|
| |
|❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚|
The LCD display test fades from light to dark and viceversa. |❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚|
|❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚|
|--- LED TEST ---|
Check that all leds are lighting. |Are all leds on?|
| |

J4

Downloaded from www.Manualslib.com manuals search engine

 Check the VOLUMES ranges from 0 to 127. Turn off the instrument and disconnect the EPROM BOARD.
| |Button test |
Check all buttons (except GRAND PIANO) pressing their one at a time and checking | |Vol:0 | Start with the instrument in AUTOTEST mode as described above and press GRAND | mmm dd yyyy |
that corresponding led lights, pressing PAGE UP and DOWN buttons the display shows | 123456| PIANO 2 times until the display show the new software version loaded in flash |hh:mm:ss V #.##|
"U" and "D", pressing DATA + and - buttons the display shows "+" and "-", pressing memory. | |
MASTER EQ and DSP buttons the display shows an "X" in 1 and 2 digits, pressing UP, |U|Button test +| |EPROM to FLASH |
LEFT, DOWN and RIGHT buttons the display shows an "X" in 3, 4, 5 and 6 digits |D|Vol:127 -| Press GRAND PIANO to skip this procedure. |push REC to prog|
respectively. | XXXXXX| | |
|Wait * |
Check the SOFT and SUSTAIN pedals, pressing each one the value change from 0 |Soft Sust Damp| |Eprom Checksum |
(released) to 127 (pressed), the DAMPER pedal varying its value continuosly from 0 | 0 0 0| The instrument performs the flash memory data checksum and display it in | |
(released) to nearly 127 (pressed). | | hexadecimal value, compare this value with the value imprinted onto the EPROM: if it
|TEST MIDI IN/OUT| matches the procedure has been executed succesfully. |cks BT PR ALL|
| #### #### ####|
Check the MIDI I/O connecting the MIDI OUT and MIDI IN sockets by a MIDI cable. |LOOP DETECTED OK|
| | | |
|TST COMPUTER I/O| The procedure proceed as described in AUTOTEST section, if you do not want to check
Check COMPUTER I/O shorting pin 3 and pin 5 on the COMPUTER socket, check with
|LOOP DETECTED OK| the rest of the instrument simply turn off it.
the oscilloscope a 4Vpp (1Mhz) signal on pin 1, set volume to half stroke. | |
The instrument generates a 1KHz sinusoidal signal in both audio channels reading | SINUS. SWEEP | RP200 O.S. UPDATING PROCEDURE from Serial Port (COMPUTER) ver. 2.xx or greater
data from 104043 ROM. VOLUME controls the amplitude of signal and TRANSPOSE b |Freq. 1000 Hz| Operation Descriptions Display
and # buttons controls the frequency from 10Hz to 2756Hz. | |
NOTE: This procedure is valid only if the software version installed on the piano is the
Re-set the frequency at 1KHz and check HEADPHONES and AUX outputs with the 2.00 or greater.
oscilloscope inserting a stereo jack in the left phones socket (speakers will go be Some additional tips and advices are included in the Flashblaster Firmware Update
silent) and two mono jack in the AUX OUT sockets and set volume to its maximum. Disk. The disk containing the Fblaster program can also be downloaded by internet at
Now verify the following level of signals: generalmusic web site (www.generalmusic.com) or required at
Phones output without load = 5,7±1.1Vpp support@generalmusic.com
AUX output = 0,8±0,16Vpp
Connect the serial cable between the COMPUTER of the piano and the RS232 COM
Set the VOLUME to minimum. port of the computer (PC-Ibm or compatible).
Apply a sinusoidal signal of 0.730Vpp at 1KHz with a generator to the AUX IN left and
Insert the disk in the drive A (or whatever your 3.5" drive is assigned to), open the
right sockets and verify the signal output:
contents of drive A and double click on the fblaster.exe file.
AUX output = 1,35±0.07Vpp
|TONE ON 104023 | From the OPTIONS/SETTINGS menu, make sure that the TEST AND PROGRAM choice
The instrument generates a tone signal in both audio channels reading data from
| | is selected. This is very important.
104023 ROM. | | |READY TO UPDATE |
|TEST END: SWITCH| Turn on the piano, while holding down the REC button until the display shows: | |
Autotest is over, turn off the instrument. |POWER TO RESTART| | |
| | |TESTING... |
Click with the mouse on the GO! button or, from the ACTION menu, select EXECUTE
|n1/n2 PACKETS |
RP200 O.S. UPDATING PROCEDURE up to ver. 2.00 with Updating Software Board (751180) (ALT+A, E). The piano display appears as follows: | |
Operation Descriptions Display | TEST OK |
| mmm dd yyyy | At the end of the test the following display appears: | |
Start with the instrument in AUTOTEST mode as described above and press GRAND | |
|hh:mm:ss V #.##|
PIANO 2 times until the display show the software version loaded in flash memory. | |
|ERASING... |
|EPROM to FLASH | After a short time, the following display appears: | |
Press GRAND PIANO to skip this procedure. |push REC to prog| | |
| | You are now erasing the old operating system from FLASH memory. When the system |UPDATING... |
|Wait * | is erased, the following display appears as your new operating system is installed into |n1/n2 PACKETS |
|Eprom Checksum | Flash Memory: | |
| |
The instrument performs the flash memory data checksum and displays it in |UPDATE_OK:SWITCH|
hexadecimal value. When the entire update procedure is completed, the following display appears: |POWER TO RESTART|
|cks BT PR ALL|
| |
| #### #### ####|
| | The update has now been successfully completed. Turn off the power switch on the
Compare the software version and checksum with the value imprinted onto the piano, and turn it back on again to use your updated instrument.
EPROM, if one of these does not match, the system must be upgraded, proceed to the
next step.
RP200 Some Repairing Tips
Turn off the instrument. Operation Descriptions Display
Insert the EPROM BOARD (where the operating system is stored) in the CN3 This message could be appear if an error occur on the communication channel.
connector located on CPU & SOUND GENERATOR BOARD. Possible solutions: |MIDI SCI error |
Start with the instrument in AUTOTEST mode as described above and press GRAND 1) inconsistent data received on MIDI or COMPUTER input socket, check the ratings of | |
PIANO 3 times. the device connected to the piano. | |
|EPROM to FLASH | 2) if the error persist, try to replace Outputs Board first and CPU board second.
When the display shows this message press REC. |push REC to prog|
| | This message could be appear if an error occur on the communication channel.
|EPROM to FLASH | Possible solutions: |VALIS SCI error |
The instrument erases the previous data in flash memory. After which the instrument |erasing | 1) verify all the connections between Keyboard Interface Board and the CPU board. | |
| | 2) if the error persist, try to replace Keyboard Interface Board first and CPU board | |
displays the amount of memory programming and finally the operation successful. If
the programming fails check the EPROM BOARD connection and repeat this procedure second.
|EPROM to FLASH |
from start. |prog: 1024/1024K| This message could be appear if an error occur on the communication between CPU
| | and DISP3 chips.
|Wait * | Possible solutions: |Disp Failure |
|Eprom Checksum | 1) verify all the tracks, solders and components between CPU and DISP3 chips as | |
The instrument performs the eprom memory data checksum and display it in | |
shown in schematics. | |
hexadecimal value, compare this value with the value imprinted onto the EPROM: if it
2) if the error persist, replace the CPU board and send back to generalmusic the failed
matches the EPROM is good. |cks BT PR ALL|
| #### #### ####| CPU board.
| |

5J

Downloaded from www.Manualslib.com manuals search engine

 J6

Downloaded from www.Manualslib.com manuals search engine

 7J

Downloaded from www.Manualslib.com manuals search engine

 J8

Downloaded from www.Manualslib.com manuals search engine

 9J

Downloaded from www.Manualslib.com manuals search engine

 J 10

Downloaded from www.Manualslib.com manuals search engine

 11 J

Downloaded from www.Manualslib.com manuals search engine

 J 12

Downloaded from www.Manualslib.com manuals search engine

 13 J

Downloaded from www.Manualslib.com manuals search engine

 J 14

Downloaded from www.Manualslib.com manuals search engine

 CPU & SOUND GENERATOR BOARD

PCB# 310603/1

15 J

Downloaded from www.Manualslib.com manuals search engine

 J 16

Downloaded from www.Manualslib.com manuals search engine

 17 J

Downloaded from www.Manualslib.com manuals search engine

 230568 * 10mH 250Vac 1A AC Line EMI Coil “Siemens” 500075 ** Mechanical Keyboard (TP21) 140877 * Jumper For Contacts Strip (p=2.54mm) 261961 * Right Foot (M)
Spare Part List 140010 * 3 Contacts P=10 Vert Terminal Block 160217 *** Sharp Key Return Spring 110282 * 3.6V 60mAh Nicd Battery 261829 * Right Foot (B)
Legend 020493 * 100n 250Vac MKP EMI Capacitor “Siemens” 160216 *** Natural Key Return Spring 261808 * Right Foot (R)
EU = Specify European Version (230Vac) 010545 * 4n7 250V Ceramic Capacitor (Iec-Ul-Csa) 151236 *** Last C Key (TP21P)
Outputs Assembly 261951 * Left Side (M)
US = Specify United States Version (115Vac) 340916 Button for Power Switch 151235 *** First A Key (TP21P) 730996 Outputs Assembly 261833 * Left Side (B)
R = Rosewood finish 190133 Lateroid Insulator For Screw Block 151234 *** Sharp Key (TP21P) 730995 * Outputs Board (Pcb#310608) 261803 * Left Side (R)
B = Gloss Black finish 171638 Mains Switch Support 151233 *** B Key (TP21P) 230569 ** FL5R200PNT EMI Coil For Signal 261950 * Right Side (M)
M = Mahogany finish 140036 Screw Block (specify contacts) 151232 *** A Key (TP21P) 230527 ** BL02RN2-R62 EMI Coil For Signal 261834 * Right Side (B)
W = Gloss White finish 110614 Mains Socket 151231 *** G Key (TP21P) 141012 ** 8 Contacts Vert Female Connector 261802 * Right Side (R)
Baldwin = Baldwin version 020493 100n 250Vac MKP EMI Capacitor “Siemens” 151230 *** F Key (TP21P) 141010 ** 4 Contacts Vert Female Connector 171702 * Right Cabinet Support
Gem = Gem version 151229 *** E Key (TP21P) 140918 ** 2 Contacts Hor Male Connector 171701 * Left Cabinet Support
Code Description
Transformers 151228 *** D Key (TP21P) 140908 ** 6 Contacts Vert Male Small Connector
Cabinet
RP100 230136
230137
Transformer 230Vac 130W (EU)
Transformer 115Vac 130W (US)
151227 *** C Key (TP21P) 140247
140217
**
**
8 Poles Mini Din Female Socket
Jack Slim Horizontal S-F Socket Top Cabinet Assembly
Controls Panel Assembly 140216 ** 6 Poles Din Horizontal Female Socket 710534 Top Cabinet Assembly (M)
Accessories Power Amplifier & Supply Board 820583 Controls Panel Assembly (Gem) 140212 ** 5 Poles Din Horizontal Female Socket 710533 Top Cabinet Assembly (B)
970243 Pianist’s Bench 730675 Power Amplifier & Supply Board (Pcb#310543) 820582 Controls Panel Assembly (Baldwin) 120857 ** Vertical Male Faston 6.3mm 710532 Top Cabinet Assembly (R)
970346 Portable Triple Pedal Switch 340154 * TO3/TO218 Mica Washer 810677 * Controls & Display Boards Assembly 100734 ** MAX202E RS232 Drivers/Receiver 510268 * Top Cover Assembly (M)
271243 Owner’s Manual (English,Italian,French,German)(Gem) 340079 * TO220 Mica Washer 730999 ** Controls Panel Board (Pcb#310609) 100602 ** 74HC04 Hex Inverter 510267 * Top Cover Assembly (B)
271266 Owner’s Manual (Dutch,Spanish,Danish)(Gem) 340078 * TO220 Insulated Bush 141018 *** 20 Contacts Vert Female Connector 100035 ** 6N138 Optocoupler 510266 * Top Cover Assembly (R)
271236 Owner’s Manual (English, French, Spanish)(Baldwin) 141010 * 4 Contacts Vert Female Connector 140918 *** 2 Contacts Hor Male Connector 090194 ** BC560 TO92 LN Pnp Transistor 261866 ** 20x20x200mm Deal Fillet
130274 Mains Cable (EU) 140917 * 2 Contacts Vert Male Connector 140529 *** Microswitch 12V 50mA 0.25mm 090183 ** BC550 TO92 LN Npn Transistor 261958 ** Cabinet Cover (M)
130276 Mains Cable (US) 140352 * 9 Contacts Hor Male Connector 100606 *** 74HC138 1 Of 8 Decoder 080103 ** 1N4148 100mA 75V Signal Diode 261837 ** Cabinet Cover (B)
140351 * 6 Contacts Hor Male Connector 090194 *** BC560 TO92 LN Pnp Transistor 653440 * Outputs Panel 261798 ** Cabinet Cover (R)
Consolette 140010 * 3 Contacts P=10 Vert Terminal Block 080752 *** Led 3mm Wide Diffused Red 210018 * 1x5mm Adhesive Red Felt (specify mt) 340090 * Music Stand Bush
970345 Consolette 110119 * Fuse Clip 10A max (EU) (US) 080724 *** Led 3mm 40deg High Eff Green 171329 * Support for Outputs Panel Front Panel Assembly
660603 * Lower Cross-Bar Strengthening 100958 * TDA7265 Dual 25W Power Amplifier 080103 *** 1N4148 100mA 75V Signal Diode 710544 Front Panel Assembly (Baldwin) (M)
660511 * Left Cabinet Support 100919 * MC33078 Dual LN Operational Amplifier 070551 *** 10K Linear 30mm Slider Potentiometer
Wiring Connections 710543 Front Panel Assembly (Baldwin) (B)
660510 * Right Cabinet Support 100059 * 7805 +5V 1A Voltage Regulator 730997 ** Display Board (Pcb#310638) 841174 20 Wires 20cm Length Flat Cable (3 Connectors) 710542 Front Panel Assembly (Baldwin) (R)
651924 * Foot 100045 * 7812 +12V 1A Voltage Regulator 323069 *** 11.1X5mm Bumpon Rubber 841173 6 Wires 7.5cm Length Crimp Terminal Cable 710523 Front Panel Assembly (Gem)(M)
261820 * Lower Cross-Bar 100043 * 7912 -12V 1A Voltage Regulator 141018 *** 20 Contacts Vert Female Connector 841172 9 Wires 15cm Length Crimp Terminal Cable 710522 Front Panel Assembly (Gem)(B)
261819 * Left Leg 090856 * J176 TO92 P-Channel J-Fet Transistor 140918 *** 2 Contacts Hor Male Connector 841043 2 Wires 35cm Length Crimp Terminal Cable 710521 Front Panel Assembly (Gem)(R)
261818 * Right Leg 090183 * BC550 TO92 LN Npn Transistor 140890 *** 4 Contacts Hor Male Single-Strip 841038 8 Wires 25cm Length Flat Cable 710553 * Front Panel (Baldwin)(M)
261092 * Upper Cross-Bar 080605 * KBL02 4A 200V Rectifier Diode Bridge 080745 *** 2x16 Characters Lcd Display 841036 6 Wires 45cm Length Flat Cable 710552 * Front Panel (Baldwin)(B)
150618 * Thumbscrew 080156 * 1N4002 1A 100V Rectifier Diode 660591 * Controls Panel (Gem) 840844 2 Wires 7.5cm Length Crimp Terminal Cable 710551 * Front Panel (Baldwin)(R)
120687 * Barrel Nut 080103 * 1N4148 100mA 75V Signal Diode 660592 * Controls Panel (Baldwin) 840842 4 Wires 15cm Length Flat Cable 710501 * Front Panel (Gem)(M)
120686 * Conical Screw 110013 T1.25A Fuse 5x20mm (EU) 653420 * <+ -> Rubber Pad 840768 4 Wires 10cm Length Flat Cable 710500 * Front Panel (Gem)(B)
120685 * Threaded Rod 110003 T3.15A Fuse 5x20mm (EU) 653419 * << >> Rubber Pad 840765 2 Wires 20cm Length Crimp Terminal Cable 710499 * Front Panel (Gem)(R)
110061 T3A Fuse 6.3x32mm (US) 653418 * <PLAY-REC> Rubber Pad 324405 * Hinge
Cabinet
710472 Cabinet (Gem)
110026 T1.25A Fuse 6.3x32mm (US) 653417
653415
*
*
2+4+8+8 Rubber Pad
5+5+2 Rubber Pad
RP150 261944
261941
*
*
Music Stand (M)
Music Stand (B)
710471 Cabinet (Baldwin)
Speakers Assembly 653413 * 4+1 Rubber Pad 261938 * Music Stand (R)
660606 Cover 770835 Speakers Cables Assembly 651648 * Plexiglass Display Screen
Accessories 219066 * Adhesive Black Felt for Music Stand
660553 Keyboard Cross-Bar (Gem) 261788 Speaker Box 340915 * LED Lens 970319 Pianist’s Bench (M) 210016 * 1x10mm Adhesive Black Felt (specify mt)
660505 Keyboard Cross-Bar (Baldwin) 220117 8ohm 5" Woofer Speaker 340820 * Slider Knob 970297 Pianist’s Bench (B) 171679 * Front Panel Angular Reinforcement
660509 Flange for Left Side 220115 8ohm 3" Tweeter Speaker 340523 * 6.5mm Spacer 970296 Pianist’s Bench (R) 171669 * Left Fixing Bar
660508 Flange for Right Side 030171 4u7 63V 20% Axial Electrolytic Bipolar Capacitor 340512 * Slider Potentiometer Guide 340116 Adhesive Clamp For Pedals Cable 171664 * Right Fixing Bar
653427 Left Side 210258 * Slider Potentiometer Felt 271276 Owner’s Manual (English,French,Spanish)(Baldwin) Keyboard Cover Assembly
653426 Right Side
Phones Board 210020 * 1.5x12mm Adhesive Red Felt (specify mt) 271259 Owner’s Manual (English,Italian,French,German)(Gem) 710520 Keyboard Cover Assembly (M)
652875 Speaker Grid 730516 Phones Board (Pcb# 310541) 210017 * 2x10mm Adhesive Black Felt (specify mt) 271267 Owner’s Manual (Dutch,Spanish,Danish)(Gem) 710519 Keyboard Cover Assembly (B)
340075 Nylon Board Spacer 230569 * FL5R200PNT EMI Coil For Signal 130274 Mains Cable (EU) 710518 Keyboard Cover Assembly (R)
210017 2x10mm Adhesive Black Felt (specify mt) 140351 * 6 Contacts Hor Male Connector
CPU & Sound Generator Board 130276 Mains Cable (US) 660612 * Front Keyboard Cover Handle
210016 1x10mm Adhesive Black Felt (specify mt) 140217 * Jack Slim Horizontal S-F Socket 761171 CPU & Sound Generator Board (Pcb#310603) 340922 * Plastic Sliding Cap for Handle
190015 Adhesive Rubber Foot 140207 * Jack Horizontal F Socket (with dual switch) 560021 * GAL 16V8C-7 Programmed Disp3 Ram Read
Consolette 340811 * Toothed Wheel
171657 Left Side Support 560020 * GAL 16V8C-7 Programmed Disp3 Ram Write 830746 Legs & Pedals Assembly (M) 340119 * Bush
171656 Right Side Support
Keyboard Assembly 141018 * 20 Contacts Vert Female Connector 830745 Legs & Pedals Assembly (B) 261949 * Keyboard Cover (M)
Music Stand 720558 Keyboard Assembly (TP21) 141012 * 8 Contacts Vert Female Connector 830744 Legs & Pedals Assembly (R) 261948 * Keyboard Cover (B)
340913 Music Stand Stop 840762 * 20 Wires 25cm Length Flat Cable 141011 * 6 Contacts Vert Female Connector 710504 * Pedals Cross-bar Assembly (M) 261947 * Keyboard Cover (R)
720566 Music Stand Assembly (Gem) 840761 * 20 Wires 12.5cm Length Flat Cable 141010 * 4 Contacts Vert Female Connector 710503 * Pedals Cross-bar Assembly (B) 210017 * 2x10mm Adhesive Black Felt (specify mt)
720564 Music Stand Assembly (Baldwin) 761173 * Keyboard Interface Board (Pcb#315024) 140930 * 9 Contacts Hor Male Connector 710502 * Pedals Cross-bar Assembly (R) 210016 * 1x10mm Adhesive Black Felt (specify mt)
710466 * Wooden Music Stand Support (Gem) 141018 ** 20 Contacts Vert Female Connector 140874 * Single In Line Vert Male Strip (specify contacts) 720561 ** Triple Brassed Pedals Assembly 171665 * Keyboard Cover Bar Support
710465 * Wooden Music Stand Support (Baldwin) 141011 ** 6 Contacts Vert Female Connector 106003 * MAX709 Power Monitor With Reset 070556 *** 20K 90deg stroke potentiometer 171335 * Toothed Wheel Bar
340914 * Plexiglass Music Stand 140918 ** 2 Contacts Hor Male Connector 106001 * MC33078P SOIC Dual Low Noise Op. Amp. 510258 ** Pedal Wooden Parts (M) 120690 * Toothed Wheel Lock
170612 * Music Stand Hinge 100740 ** HD6433278 Cpu F=20MHz 105009 * DISP3 QFP Digital Sound Processor (Hitachi) 510257 ** Pedal Wooden Parts (B) Cabinet Assembly
210017 * 2x10mm Adhesive Black Felt (specify mt) 100605 ** 74HC125 Quad 3-State Buffer 105006 * HD6413003F16 QFP Cpu 510256 ** Pedal Wooden Parts (R) 710557 Cabinet (Baldwin) (M)
Keyboard Cover 050493 ** 10Kx4 1/8w 5% Resistor Array 104042 * HM5118160J-5 16Mbit Dram Ta=50nS 261965 *** 20x20x70mm Deal Fillet 710556 Cabinet (Baldwin) (B)
653431 Left Rack 050492 ** 10Kx8 1/8w 5% Resistor Array 104041 * 23C64000G SOP 64MBit Rom Wave98 261946 *** Rear Cross-Bar for Pedals 710555 Cabinet (Baldwin) (R)
653430 Right Rack 050414 ** 2K2x4 1/8w 5% Resistor Array 104030 * AM29F400B-90EC TSOP 4Mbit Flash Memory Ta=90nS 261866 *** 20x20x200mm Deal Fillet 710513 Cabinet (Gem) (M)
340811 Toothed Wheel 010725 ** 20MHz Ceramic Resonator With Capacitors 104000 * HM628128LFP5 SOP 1Mbit Static Ram Ta=55nS 261812 *** Support for Pedalboard 710512 Cabinet (Gem) (B)
171651 Toothed Wheel Bar 010662 ** 220p 10% 50V X8 Cap Array 103012 * 74HC125D SOIC Quad Tri-State Buffer 261952 *** Top Cross-Bar for Pedals (M) 710511 Cabinet (Gem) (R)
120690 Toothed Wheel Lock 010661 ** 47p 10% 50V X8 Cap Array 103010 * 74HC04D SOIC Hex Inverter 261831 *** Top Cross-Bar for Pedals (B) 660609 * Speaker Socket Support
720565 Keyboard Cover Assembly 720560 * Keyboard Assembly (TP21) 103009 * 74HC02D SOIC Quad 2-In Nor Gate 261806 *** Top Cross-Bar for Pedals (R) 660410 * Speakers Protection Grid
660599 * Bar Support Profile for Keyb. Cover 840738 ** 4 Wires 5cm Length Flat Cable 103004 * AD1865R SOP 18bit D/A Converter 261953 *** Front Cross-Bar for Pedals (M) 660405 * Heatsink Grid
660598 * Top Handle Profile for Keyb. Cover 810552 ** 39 Contacts L Board For Dynamic Keyb. (PCB#310531) 103002 * 74HC245DW SOIC Octal Bus Transceiver 261830 *** Front Cross-Bar for Pedals (B) 510264 * Cabinet Wooden Parts (Baldwin) (M)
660597 * Bottom Handle Profile for Keyb. Cover 340764 *** 3 Dual Contacts Rubber Strip 103001 * 74HC08D SOIC Quad 2-Input And Gate 261807 *** Front Cross-Bar for Pedals (R) 510262 * Cabinet Wooden Parts (Baldwin) (B)
340922 * Plastic Sliding Cap for Handle 340211 *** 12 Dual Contact Rubber Strip 091001 * BC857 TO236 Smd Pnp Transistor 261811 ** Pedalboard 510260 * Cabinet Wooden Parts (Baldwin) (R)
340912 * Plexiglass Keyboard Cover 141018 *** 20 Contacts Vert Female Connector 091000 * BC847 TO236 Smd Npn Transistor 210021 ** 1x15mm Adhesive Red Felt (specify mt) 510263 * Cabinet Wooden Parts (Gem) (M)
340119 * Bush 141010 *** 4 Contacts Vert Female Connector 081204 * 5.6V 0.5W Zener 171585 ** Angular Fixing for Pedals Cross-bar 510261 * Cabinet Wooden Parts (Gem) (B)
190015 * Adhesive Rubber Foot 080103 *** 1N4148 100mA 75V Signal Diode 081000 * PMLL4148 Smd 100mA 75V Signal Diode 660407 * Speaker Box Fixing 510259 * Cabinet Wooden Parts (Gem) (R)
810551 ** 49 Contacts R Board For Dynamic Keyb. (PCB#310530) 055101 * 4K7 X4 1/16w 5% Smd Resistor Array 261943 * Lower Panel (M) 710540 ** Keyboard Cross-Bar (Baldwin) (M)
Mains Assembly 340212 *** 13 Dual Contact Rubber Strip 055100 * 100E X4 1/16w 5% Smd Resistor Array 261940 * Lower Panel (B) 710480 ** Keyboard Cross-Bar (Baldwin) (B)
770839 Mains Cables Assembly 340211 *** 12 Dual Contact Rubber Strip 011501 * 220pF x4 10% 100V NP0 Smd Capacitor Array 261937 * Lower Panel (R) 710469 ** Keyboard Cross-Bar (Baldwin) (R)
770834 Power Switch Cables Assembly 141018 *** 20 Contacts Vert Female Connector 011500 * 47pF x4 10% 100V NP0 Smd Capacitor Array 261962 * Left Foot (M) 710497 ** Keyboard Cross-Bar (Gem) (M)
110320 * Power Switch 141010 *** 4 Contacts Vert Female Connector 010727 * 45.1584MHz Quartz Resonator 261828 * Left Foot (B) 710481 ** Keyboard Cross-Bar (Gem) (B)
768197 Mains Filter Board (Pcb#310642) 080103 *** 1N4148 100mA 75V Signal Diode 010704 * 16MHz Quartz Resonator 261809 * Left Foot (R) 710470 ** Keyboard Cross-Bar (Gem) (R)

J 18

Downloaded from www.Manualslib.com manuals search engine

 710541 ** Rear Panel (Baldwin) (M) 050493 ** 10Kx4 1/8w 5% Resistor Array 105009 * DISP3 QFP Digital Sound Processor (Hitachi) 271237 Owner’s Manual (English, Italian, French, German)(Gem) 710532 Top Cabinet Assembly (R)
710474 ** Rear Panel (Baldwin) (B) 050492 ** 10Kx8 1/8w 5% Resistor Array 105006 * HD6413003F16 QFP Cpu 271268 Owner’s Manual (Dutch,Spanish,Danish)(Gem) 710546 Top Cabinet Assembly (W)
710467 ** Rear Panel (Baldwin) (R) 050414 ** 2K2x4 1/8w 5% Resistor Array 104042 * HM5118160J-5 16Mbit Dram Ta=50nS 271258 Owner’s Manual (English, French, Spanish)(Baldwin) 510268 * Top Cover Assembly (M)
710498 ** Rear Panel (Gem) (M) 010725 ** 20MHz Ceramic Resonator With Capacitors 104041 * 23C64000G SOP 64MBit Rom Wave98 130274 Mains Cable (EU) 510267 * Top Cover Assembly (B)
710475 ** Rear Panel (Gem) (B) 010662 ** 220p 10% 50V X8 Cap Array 104030 * AM29F400B-90EC TSOP 4Mbit Flash Memory Ta=90nS 130276 Mains Cable (US) 510266 * Top Cover Assembly (R)
710468 ** Rear Panel (Gem) (R) 010661 ** 47p 10% 50V X8 Cap Array 104000 * HM628128LFP5 SOP 1Mbit Static Ram Ta=55nS 510269 * Top Cover Assembly (W)
261840 ** Bottom Support Panel 720559 * Keyboard Assembly (TP10MDS) 103012 * 74HC125D SOIC Quad Tri-State Buffer
Consolette 261866 ** 20x20x200mm Deal Fillet
261954 ** Cabinet Right Side (M) 840738 ** 4 Wires 5cm Length Flat Cable 103010 * 74HC04D SOIC Hex Inverter 830743 Legs & Pedals Assembly (M) 261958 ** Cabinet Cover (M)
261841 ** Cabinet Right Side (B) 810552 ** 39 Contacts L Board For Dynamic Keyb. (PCB#310531) 103009 * 74HC02D SOIC Quad 2-In Nor Gate 830742 Legs & Pedals Assembly (B) 261837 ** Cabinet Cover (B)
261791 ** Cabinet Right Side (R) 340764 *** 3 Dual Contacts Rubber Strip 103004 * AD1865R SOP 18bit D/A Converter 830741 Legs & Pedals Assembly (R) 261798 ** Cabinet Cover (R)
261955 ** Cabinet Left Side (M) 340211 *** 12 Dual Contact Rubber Strip 103002 * 74HC245DW SOIC Octal Bus Transceiver 830752 Legs & Pedals Assembly (W) 261853 ** Cabinet Cover (W)
261842 ** Cabinet Left Side (B) 141018 *** 20 Contacts Vert Female Connector 103001 * 74HC08D SOIC Quad 2-Input And Gate 710530 * Cloth Panel Assembly 340090 * Music Stand Bush
261790 ** Cabinet Left Side (R) 141010 *** 4 Contacts Vert Female Connector 091001 * BC857 TO236 Smd Pnp Transistor 340159 ** 3M Dual Lock Fastening (Specify mt) Front Panel Assembly
340904 * Toothed Bar 080103 *** 1N4148 100mA 75V Signal Diode 091000 * BC847 TO236 Smd Npn Transistor 261805 ** Cloth Panel 710528 Front Panel Assembly (Gem)(M)
323012 * Plastic Pivot 810551 ** 49 Contacts R Board For Dynamic Keyb. (PCB#310530) 081204 * 5.6V 0.5W Zener 210074 ** Speaker Cloth 710526 Front Panel Assembly (Gem)(B)
171331 * Left Cover Clamp 340212 *** 13 Dual Contact Rubber Strip 081000 * PMLL4148 Smd 100mA 75V Signal Diode 710517 * Speaker Box Assembly (M) 710524 Front Panel Assembly (Gem)(R)
171330 * Right Cover Clamp 340211 *** 12 Dual Contact Rubber Strip 055101 * 4K7 X4 1/16w 5% Smd Resistor Array 710516 * Speaker Box Assembly (B) 710529 Front Panel Assembly (Baldwin)(M)
150474 * Plug For Unused Hole 141018 *** 20 Contacts Vert Female Connector 055100 * 100E X4 1/16w 5% Smd Resistor Array 710515 * Speaker Box Assembly (R) 710527 Front Panel Assembly (Baldwin)(B)
653433 Left Plastic Lateral 141010 *** 4 Contacts Vert Female Connector 011501 * 220pF x4 10% 100V NP0 Smd Capacitor Array 710549 * Speaker Box Assembly (W) 710525 Front Panel Assembly (Baldwin)(R)
653432 Right Plastic Lateral 080103 *** 1N4148 100mA 75V Signal Diode 011500 * 47pF x4 10% 100V NP0 Smd Capacitor Array 770727 ** Speaker Cables Assembly 710545 Front Panel Assembly (Baldwin)(W)
340075 Nylon Board Spacer 500074 ** Mechanicals Parts (TP10MDS) 010727 * 45.1584MHz Quartz Resonator 510265 ** Speaker Box (M) 710536 * Front Finishing Fillet (Gem) (M)
210217 Black Sealer (specify mt) 151226 *** Last C Key (TP10MDS) 010704 * 16MHz Quartz Resonator 510243 ** Speaker Box (B) 710535 * Front Finishing Fillet (Gem) (B)
210216 Adhesive Rubber Foam 20x5mm (Specify mt) 151225 *** First A Key (TP10MDS) 140877 * Jumper For Contacts Strip (p=2.54mm) 510245 ** Speaker Box (R) 710531 * Front Finishing Fillet (Gem) (R)
210054 1x5mm Adhesive Spik (specify mt) 151224 *** Sharp Key (TP10MDS) 110282 * 3.6V 60mAh Nicd Battery 510244 ** Speaker Box (W) 710539 * Front Finishing Fillet (Baldwin) (M)
151223 *** B Key (TP10MDS) 261963 *** Speaker Box Rear Panel (M) 710538 * Front Finishing Fillet (Baldwin) (B)
Mains Assembly 151222 *** A Key (TP10MDS)
HF Crossover Filter Board 261832 *** Speaker Box Rear Panel (B) 710537 * Front Finishing Fillet (Baldwin) (R)
770860 Mains Cables Assembly 151221 *** G Key (TP10MDS) 731019 HF Crossover Filter Board (Pcb#310654) 261804 *** Speaker Box Rear Panel (R) 710548 * Front Finishing Fillet (Baldwin) (W)
110320 * Power Switch 151220 *** F Key (TP10MDS) 140323 * 6 Contacts Vert Male Connector 261848 *** Speaker Box Rear Panel (W) 340919 * Music Stand
340916 Switch Button 151219 *** E Key (TP10MDS) 060253 * 10E 5W 10% Wire Resistor 261823 *** Speaker Box Lower Panel 261959 * Centre Front Panel (M)
171638 Mains Switch Support 151218 *** D Key (TP10MDS) 030348 * 47u 100V 20% Axial Electrolytic Bipolar Capacitor 261822 *** Speaker Box Upper Panel 261839 * Centre Front Panel (B)
110614 Mains Socket 151217 *** C Key (TP10MDS) 261821 *** Speaker Box Divider Panel 261795 * Centre Front Panel (R)
768197 Mains Filter Board (Pcb#310642) 340092 * 5mm Board Spacer
Outputs Assembly 261794 *** Speaker Box Front Panel 261855 * Centre Front Panel (W)
230568 * 10mH 250Vac 1A AC Line EMI Coil “Siemens” 210017 * 2x10mm Adhesive Black Felt (specify mt) 730996 Outputs Assembly 261793 *** Speaker Box Side Panel 261796 * Wooden Front Panel
140010 * 3 Contacts P=10 Vert Terminal Block 730995 * Outputs Board (Pcb#310608) 340159 ** 3M Dual Lock Fastening (Specify mt) 210016 * 1x10mm Adhesive Black Felt (specify mt)
020493 * 100n 250Vac MKP EMI Capacitor “Siemens”
Controls Panel Assembly 230569 ** FL5R200PNT EMI Coil For Signal 220118 ** 8ohm 8" Woofer Speaker 171677 * Left Speaker Grid
010545 * 4n7 250V Ceramic Capacitor (Iec-Ul-Csa) 820592 Controls Panel Assembly (Baldwin) 230527 ** BL02RN2-R62 EMI Coil For Signal 210242 ** Filler for Speaker Box (Specify m²) 171669 * Left Fixing Bar
820590 Controls Panel Assembly (Gem) 141012 ** 8 Contacts Vert Female Connector 710504 * Pedals Cross-bar Assembly (M) 171667 * Right Speaker Grid
Transformer 810677 * Controls & Display Boards Assembly 141010 ** 4 Contacts Vert Female Connector 710503 * Pedals Cross-bar Assembly (B) 171664 * Right Fixing Bar
230137 Transformer 115Vac 130W (US) 730999 ** Controls Panel Board (Pcb#310609) 140918 ** 2 Contacts Hor Male Connector 710502 * Pedals Cross-bar Assembly (R) Keyboard Cover Assembly
230136 Transformer 230Vac 130W (EU) 141018 *** 20 Contacts Vert Female Connector 140908 ** 6 Contacts Vert Male Small Connector 710550 * Pedals Cross-bar Assembly (W) 710520 Keyboard Cover Assembly (M)
140918 *** 2 Contacts Hor Male Connector 140247 ** 8 Poles Mini Din Female Socket 720561 ** Triple Brassed Pedals Assembly 710519 Keyboard Cover Assembly (B)
Power Amplifier & Supply Board 140529 *** Microswitch 12V 50mA 0.25mm 140217 ** Jack Slim Horizontal S-F Socket 510258 ** Pedal Wooden Parts (M) 710518 Keyboard Cover Assembly (R)
730675 Power Amplifier & Supply Board (Pcb#310543) 100606 *** 74HC138 1 Of 8 Decoder 140216 ** 6 Poles Din Horizontal Female Socket 510257 ** Pedal Wooden Parts (B) 710547 Keyboard Cover Assembly (W)
340154 * TO3/TO218 Mica Washer 090194 *** BC560 TO92 LN Pnp Transistor 140212 ** 5 Poles Din Horizontal Female Socket 510256 ** Pedal Wooden Parts (R) 660612 * Front Keyboard Cover Handle
340079 * TO220 Mica Washer 080752 *** Led 3mm Wide Diffused Red 100734 ** MAX202E RS232 Drivers/Receiver 510270 ** Pedal Wooden Parts (W) 340922 * Plastic Sliding Cap for Handle
340078 * TO220 Insulated Bush 080724 *** Led 3mm 40deg High Eff Green 100602 ** 74HC04 Hex Inverter 261965 *** 20x20x70mm Deal Fillet 340811 * Toothed Wheel
141010 * 4 Contacts Vert Female Connector 080103 *** 1N4148 100mA 75V Signal Diode 100035 ** 6N138 Optocoupler 261946 *** Rear Cross-Bar for Pedals 340119 * Bush
140917 * 2 Contacts Vert Male Connector 070551 *** 10K Linear 30mm Slider Potentiometer 090194 ** BC560 TO92 LN Pnp Transistor 261866 *** 20x20x200mm Deal Fillet 261949 * Keyboard Cover (M)
140352 * 9 Contacts Hor Male Connector 730997 ** Display Board (Pcb#310638) 090183 ** BC550 TO92 LN Npn Transistor 261952 *** Top Cross-Bar for Pedals (M) 261948 * Keyboard Cover (B)
140351 * 6 Contacts Hor Male Connector 323069 *** 11.1X5mm Bumpon Rubber 080103 ** 1N4148 100mA 75V Signal Diode 261831 *** Top Cross-Bar for Pedals (B) 261947 * Keyboard Cover (R)
140010 * 3 Contacts P=10 Vert Terminal Block 141018 *** 20 Contacts Vert Female Connector 653440 * Output Panel Box 261806 *** Top Cross-Bar for Pedals (R) 261978 * Keyboard Cover (W)
110119 * Fuse Clip 10A max (EU) (US) 140918 *** 2 Contacts Hor Male Connector 210018 * 1x5mm Adhesive Red Felt (specify mt) 261847 *** Top Cross-Bar for Pedals (W) 210017 * 2x10mm Adhesive Black Felt (specify mt)
100958 * TDA7265 Dual 25W Power Amplifier 140890 *** 4 Contacts Hor Male Single-Strip 171329 * Support for Output Panel Box 261953 *** Front Cross-Bar for Pedals (M) 210016 * 1x10mm Adhesive Black Felt (specify mt)
100919 * MC33078 Dual LN Operational Amplifier 080745 *** 2x16 Characters Lcd Display 261830 *** Front Cross-Bar for Pedals (B) 171665 * Keyboard Cover Bar Support
100059 * 7805 +5V 1A Voltage Regulator 660635 * Control Panel (Baldwin)
Phones Assembly 261807 *** Front Cross-Bar for Pedals (R) 171335 * Toothed Wheel Bar
100045 * 7812 +12V 1A Voltage Regulator 660610 * Control Panel (Gem) 730674 Phones Assembly 261846 *** Front Cross-Bar for Pedals (W) 120690 * Toothed Wheel Lock
100043 * 7912 -12V 1A Voltage Regulator 653420 * <+ -> Rubber Pad 730516 * Phones Board (pcb# 310541) 261812 *** Support for Pedalboard Cabinet Assembly
090856 * J176 TO92 P-Channel J-Fet Transistor 653419 * << >> Rubber Pad 230569 ** FL5R200PNT EMI Coil For Signal 261811 ** Pedalboard 710509 Cabinet (Gem) (M)
090183 * BC550 TO92 LN Npn Transistor 653418 * <PLAY-REC> Rubber Pad 140351 ** 6 Contacts Hor Male Connector 210021 ** 1x15mm Adhesive Red Felt (specify mt) 710507 Cabinet (Gem) (B)
080605 * KBL02 4A 200V Rectifier Diode Bridge 653417 * 2+4+8+8 Rubber Pad 140217 ** Jack Slim Horizontal S-F Socket 171585 ** Angular Fixing for Pedals Cross-bar 710505 Cabinet (Gem) (R)
080156 * 1N4002 1A 100V Rectifier Diode 653415 * 5+5+2 Rubber Pad 140207 ** Jack Horizontal F Socket (with dual switch) 120681 ** Sleeve for Internal Cheek Block 710510 Cabinet (Baldwin) (M)
080103 * 1N4148 100mA 75V Signal Diode 653413 * 4+1 Rubber Pad 652854 * Phones Board Support 660407 * Speaker Box Fixing 710508 Cabinet (Baldwin) (B)
110013 T1.25A Fuse 5x20mm (EU) 651648 * Plexiglass Display Screen 210017 * 2x10mm Adhesive Black Felt (specify mt) 261950 * Right Side (M) 710506 Cabinet (Baldwin) (R)
110003 T3.15A Fuse 5x20mm (EU) 651563 * Cloth For Panel Slits 261834 * Right Side (B) 710554 Cabinet (Baldwin) (W)
110061 T3A Fuse 6.3x32mm (US) 340915 * LED Lens
Wiring Connections 261802 * Right Side (R) 660609 * Speaker Socket Support
110026 T1.25A Fuse 6.3x32mm (US) 340820 * Slider Knob 841206 4 Wires 20cm Length Flat Cable 261850 * Right Side (W) 660405 * Heatsink Grid
340523 * 6.5mm Spacer 841205 9 Wires 7.5cm Length Crimp Terminal Cable 261951 * Left Side (M) 510263 * Cabinet Wooden Parts (Gem) (M)
Speakers Assembly 340512 * Slider Potentiometer Guide 841176 20 Wires 48cm Length Flat Cable (3 Connectors) 261833 * Left Side (B) 510261 * Cabinet Wooden Parts (Gem) (B)
770859 Speaker Cables Assembly 210258 * Slider Potentiometer Felt 841173 6 Wires 7.5cm Length Crimp Terminal Cable 261803 * Left Side (R) 510259 * Cabinet Wooden Parts (Gem) (R)
220120 6" Full-range 8E Speaker 210020 * 1.5x12mm Adhesive Red Felt (specify mt) 841063 6 Wires 55cm Length Flat Cable 261849 * Left Side (W) 510264 * Cabinet Wooden Parts (Baldwin) (M)
220119 3" Full-range 8E Speaker 210017 * 2x10mm Adhesive Black Felt (specify mt) 841043 2 Wires 35cm Length Crimp Terminal Cable 261961 * Right Foot (M) 510262 * Cabinet Wooden Parts (Baldwin) (B)
340928 Plastic Speaker Box 171661 * Front Support 841041 8 Wires 12.5cm Length Flat Cable 261829 * Right Foot (B) 510260 * Cabinet Wooden Parts (Baldwin) (R)
210242 Filler for Speaker Box (Specify m²) 841010 2 Wires 50cm Length Crimp Terminal Cable 261808 * Right Foot (R) 510271 * Cabinet Wooden Parts (Baldwin) (W)
171699 3" Speaker Support
CPU & Sound Generator Board 840844 2 Wires 7.5cm Length Crimp Terminal Cable 261845 * Right Foot (W) 710497 ** Keyboard Cross-Bar (Gem) (M)
761171 CPU & Sound Generator Board (Pcb#310603) 840799 4 Wires 7.5cm Length Flat Cable 261962 * Left Foot (M) 710481 ** Keyboard Cross-Bar (Gem) (B)
Keyboard Assembly 560021 * GAL 16V8C-7 <DISP3 RAM READ 261828 * Left Foot (B) 710470 ** Keyboard Cross-Bar (Gem) (R)
720568
840762
Keyboard Assembly (TP10MDS)
* 20 Wires 25cm Length Flat Cable
560020
141018
*
*
GAL 16V8C-7 <DISP3 RAM WRITE
20 Contacts Vert Female Connector
RP200 261809
261844
*
*
Left Foot (R)
Left Foot (W)
710540
710480
**
**
Keyboard
Keyboard
Cross-Bar
Cross-Bar
(Baldwin) (M)
(Baldwin) (B)
840761 * 20 Wires 12.5cm Length Flat Cable 141012 * 8 Contacts Vert Female Connector 171702 * Right Cabinet Support 710469 ** Keyboard Cross-Bar (Baldwin) (R)
761173 * Keyboard Interface Board (Pcb#315024) 141011 * 6 Contacts Vert Female Connector
Accessories 171701 * Left Cabinet Support 710476 ** Keyboard Cross-Bar (Baldwin) (W)
141018 ** 20 Contacts Vert Female Connector 141010 * 4 Contacts Vert Female Connector 970319 Pianist’s Bench (M) 710498 ** Rear Panel (Gem) (M)
141011 ** 6 Contacts Vert Female Connector 140930 * 9 Contacts Hor Male Connector 970297 Pianist’s Bench (B)
Cabinet 710475 ** Rear Panel (Gem) (B)
140918 ** 2 Contacts Hor Male Connector 140874 * Single In Line Vert Male Strip (specify contacts) 970296 Pianist’s Bench (R) Top Cabinet Assembly 710468 ** Rear Panel (Gem) (R)
100740 ** HD6433278 Cpu F=20MHz 106003 * MAX709 Power Monitor With Reset 970298 Pianist’s Bench (W) 710534 Top Cabinet Assembly (M) 710541 ** Rear Panel (Baldwin) (M)
100605 ** 74HC125 Quad 3-State Buffer 106001 * MC33078P SOIC Dual Low Noise Op. Amp. 340116 Adhesive Clamp For Pedals Cable 710533 Top Cabinet Assembly (B) 710474 ** Rear Panel (Baldwin) (B)

19 J

Downloaded from www.Manualslib.com manuals search engine

 710467 ** Rear Panel (Baldwin) (R) 710514 Mid-Speaker Box Assembly 731001 ** Controls Panel Board (Pcb#310622) 140216 ** 6 Poles Din Horizontal Female Socket
710478 ** Rear Panel (Baldwin) (W) 770845 * Mid-Speaker Cables Assembly 141018 *** 20 Contacts Vert Female Connector 140212 ** 5 Poles Din Horizontal Female Socket
261955 ** Cabinet Left Side (M) 141107 ** 4 Contacts Female Connector Housing 140918 *** 2 Contacts Hor Male Connector 120857 ** Vertical Male Faston 6.3mm
261842 ** Cabinet Left Side (B) 141105 ** Female Crimping Contact 140529 *** Microswitch 12V 50mA 0.25mm 100734 ** MAX202E RS232 Drivers/Receiver
261790 ** Cabinet Left Side (R) 510246 * Midrange Box 100606 *** 74HC138 1 Of 8 Decoder 100602 ** 74HC04 Hex Inverter
261858 ** Cabinet Left Side (W) 229015 * 8ohm 20W 1" Dome Tweeter Speaker 090194 *** BC560 TO92 LN Pnp Transistor 100035 ** 6N138 Optocoupler
261954 ** Cabinet Right Side (M) 220117 * 8ohm 5" Woofer Speaker 080752 *** Led 3mm Wide Diffused Red 090194 ** BC560 TO92 LN Pnp Transistor
261841 ** Cabinet Right Side (B) 080724 *** Led 3mm 40deg High Eff Green 090183 ** BC550 TO92 LN Npn Transistor
261791 ** Cabinet Right Side (R)
Mixer & Phones Amp. Board 080103 *** 1N4148 100mA 75V Signal Diode 080103 ** 1N4148 100mA 75V Signal Diode
261857 ** Cabinet Right Side (W) 731024 Mixer & Phones Amp. Board (Pcb#310658) 070551 *** 10K Linear 30mm Slider Potentiometer 653440 * Outputs Panel
261840 ** Bottom Support Panel 141011 * 6 Contacts Vert Female Connector 731000 ** Display Board (Pcb#310637) 210018 * 1x5mm Adhesive Red Felt (specify mt)
340904 * Toothed Bar 141010 * 4 Contacts Vert Female Connector 141018 *** 20 Contacts Vert Female Connector 171329 * Support for Outputs Panel
323012 * Plastic Pivot 140935 * 6 Contacts Hor Male Connector 140918 *** 2 Contacts Hor Male Connector
261813 * Midrange Cabinet Support 140918 * 2 Contacts Hor Male Connector 140874 *** Single In Line Vert Male Strip (specify contacts)
Wiring Connections
171331 * Left Cover Clamp 140889 * Dual In Line Vert Male Strip (specify contacts) 090194 *** BC560 TO92 LN Pnp Transistor 841182 9 Wires 25cm Length Flat Cable
171330 * Right Cover Clamp 140872 * 4 Contatcs Hor Male Connector 080754 *** LMC97S005A Lcd Display 128X64 dots 841181 6 Wires 15cm Length Flat Cable
653433 Left Plastic Lateral 110305 * Relay 12V / 2 Switch 1A 250V 080103 *** 1N4148 100mA 75V Signal Diode 841178 6 Wires 35cm Length Flat Cable
653432 Right Plastic Lateral 106007 * TDA8542AT SOIC 2X1.5W BTL Audio Amplifier 660594 * Controls Panel (Gem) 841176 20 Wires 48cm Length Flat Cable (3 Connectors)
340075 Nylon Board Spacer 100919 * MC33078 Dual LN Operational Amplifier 660593 * Controls Panel (Baldwin) 841057 4 Wires 60cm Length Crimp Terminal Cable
090183 * BC550 TO92 LN Npn Transistor 653420 * <+ -> Rubber Pad 841043 2 Wires 35cm Length Crimp Terminal Cable
Mains Assembly 080241 * 5V6 1W 5% Zener Diode 653419 * << >> Rubber Pad 841038 8 Wires 25cm Length Flat Cable
110614 Mains Socket 080156 * 1N4002 1A 100V Rectifier Diode 653417 * 2+4+8+8 Rubber Pad 841036 6 Wires 45cm Length Flat Cable
770844 Power Switch & Cables Assembly 080103 * 1N4148 100mA 75V Signal Diode 653416 * 5+5+2 (PLAY-REC) Rubber Pad 841010 2 Wires 50cm Length Crimp Terminal Cable
110320 * Power Switch 653414 * 5+5+2 (SPLIT-PERF) Rubber Pad 840844 2 Wires 7.5cm Length Crimp Terminal Cable
340916 Button for Power Switch
Phones Assembly 653413 * 4+1 Rubber Pad 840810 4 Wires 30cm Length Flat Cable
171638 Mains Switch Support 731018 Phones Assembly 652735 * Display Screen 840799 4 Wires 7.5cm Length Flat Cable
770839 Mains Cables Assembly 731007 * Phones Board (Pcb#310513) 340915 * LED Lens 840792 4 Wires 35cm Length Flat Cable
768198 Mains Filter Board (Pcb#310643) 230569 ** FL5R200PNT EMI Coil For Signal 340820 * Slider Knob 840782 6 Wires 35cm Length Flat Cable
230565 * 2.5mH 250V 3A AC Line Filter 140872 ** 4 Contatcs Hor Male Connector 340523 * 6.5mm Spacer 840767 2 Wires 30cm Length Crimp Terminal Cable
140010 * 3 Contacts P=10 Vert Terminal Block 140217 ** Jack Slim Horizontal S-F Socket 340512 * Slider Potentiometer Guide
020493 * 100n 250Vac MKP EMI Capacitor “Siemens” 140207 ** Jack Horizontal F Socket (with dual switch) 210258 * Slider Potentiometer Felt
010545 * 4n7 250V Ceramic Capacitor (Iec-Ul-Csa) 120849 ** Hor Pc Male Faston 2.8 210020 * 1.5x12mm Adhesive Red Felt (specify mt)
Updating Software Board
652854 * Phones Board Support 210017 * 2x10mm Adhesive Black Felt (specify mt) 751180 Updating Software Board (Pcb#315166)
Transformer Assembly 171327 * Phones Board Fixing 550657 Eprom with Last Software Version for RP90-100-150 Digital
730453 * Transformer Assembly 230Vac (EU)
CPU & Sound Generator Board Piano
730470 * Transformer Assembly 115Vac (US)
Keyboard Assembly 761172 CPU & Sound Generator Board (Pcb#310603) 550658 Eprom with Last Software Version for RP200 GRP300 Digital
340329 ** Rubber Bush 720568 Keyboard Assembly (TP10MDS) 761189 CPU & S.G. Board (Pcb#310661) limited edition for 104046 Piano
230130 ** Transformer 230Vac 220W (EU) 840762 * 20 Wires 25cm Length Flat Cable see schematics for explanation about limited edition.
230131 ** Transformer 115Vac 220W (US) 840761 * 20 Wires 12.5cm Length Flat Cable 560021 * GAL 16V8C-7 Programmed Disp3 Ram Read
190133 ** Lateroid Insulator For Screw Block 761173 * Keyboard Interface Board (Pcb#315024) 560020 * GAL 16V8C-7 Programmed Disp3 Ram Write
140036 ** Screw Block (specify contacts) 141018 ** 20 Contacts Vert Female Connector 141018 * 20 Contacts Vert Female Connector
141011 ** 6 Contacts Vert Female Connector 141012 * 8 Contacts Vert Female Connector
Power Amplifier & Supply Board 140918 ** 2 Contacts Hor Male Connector 141011 * 6 Contacts Vert Female Connector
731004 Power Amplifier & Supply Board (Pcb#310604) 100740 ** HD6433278 Cpu F=20MHz 141010 * 4 Contacts Vert Female Connector
340154 * TO3/TO218 Mica Washer 100605 ** 74HC125 Quad 3-State Buffer 140874 * Single In Line Vert Male Strip (specify contacts)
340079 * TO220 Mica Washer 050493 ** 10Kx4 1/8w 5% Resistor Array 110282 * 3.6V 60mAh Nicd Battery
340078 * TO220 Insulated Bush 050492 ** 10Kx8 1/8w 5% Resistor Array 106003 * MAX709 Power Monitor With Reset
230527 * BL02RN2-R62 EMI Coil For Signal 050414 ** 2K2x4 1/8w 5% Resistor Array 106001 * MC33078P SOIC Dual Low Noise Op. Amp.
230524 * 100uH Switching Coil 010725 ** 20MHz Ceramic Resonator With Capacitors 105009 * DISP3 QFP Digital Sound Processor (Hitachi)
171660 * Right Support Board 010662 ** 220p 10% 50V X8 Cap Array 105006 * HD6413003F16 QFP Cpu
171659 * Left Support Board 010661 ** 47p 10% 50V X8 Cap Array 104041 * 23C64000G SOP 64MBit Rom Wave98
141101 * 4 Contacts Vert Male Connector 720559 * Keyboard Assembly (TP10MDS) 104030 * AM29F400B-90EC TSOP 4Mbit Flash Memory Ta=90nS
141010 * 4 Contacts Vert Female Connector 840738 ** 4 Wires 5cm Length Flat Cable 104023 * 23C32000G SOP 32Mbit Rom “ProWave3”
140929 * 9 Contacts Vert Male Connector 810552 ** 39 Contacts L Board For Dynamic Keyb. (PCB#310531) 104046 * 32Mbit Rom “ProWave3” limited edition for pcb#310661
140917 * 2 Contacts Vert Male Connector 340764 *** 3 Dual Contacts Rubber Strip 104014 * HN624316FBC30 SOP 16Mbit Rom “Library”
140908 * 6 Contacts Vert Male Small Connector 340211 *** 12 Dual Contact Rubber Strip 104000 * HM628128LFP5 SOP 1Mbit Static Ram Ta=55nS
140010 * 3 Contacts P=10 Vert Terminal Block 141018 *** 20 Contacts Vert Female Connector 103012 * 74HC125D SOIC Quad Tri-State Buffer
110119 * Fuse Clip 10A max (EU) (US) 141010 *** 4 Contacts Vert Female Connector 103010 * 74HC04D SOIC Hex Inverter
100965 * TDA7294 70W Audio Amplifier with Mute 080103 *** 1N4148 100mA 75V Signal Diode 103009 * 74HC02D SOIC Quad 2-In Nor Gate
100900 * L4960 5-40V 2.5A Switching Regulator 810551 ** 49 Contacts R Board For Dynamic Keyb. (PCB#310530) 103004 * AD1865R SOP 18bit D/A Converter
100045 * 7812 +12V 1A Voltage Regulator 340212 *** 13 Dual Contact Rubber Strip 103002 * 74HC245DW SOIC Octal Bus Transceiver
100043 * 7912 -12V 1A Voltage Regulator 340211 *** 12 Dual Contact Rubber Strip 103001 * 74HC08D SOIC Quad 2-Input And Gate
090183 * BC550 TO92 LN Npn Transistor 141018 *** 20 Contacts Vert Female Connector 091001 * BC857 TO236 Smd Pnp Transistor
080605 * KBL02 4A 200V Rectifier Diode Bridge 141010 *** 4 Contacts Vert Female Connector 091000 * BC847 TO236 Smd Npn Transistor
080171 * FE6B 6A 100V Fast Recovery Diode 080103 *** 1N4148 100mA 75V Signal Diode 081204 * 5.6V 0.5W Zener
080156 * 1N4002 1A 100V Rectifier Diode 500074 ** Mechanicals Parts (TP10MDS) 081000 * PMLL4148 Smd 100mA 75V Signal Diode
080103 * 1N4148 100mA 75V Signal Diode 160214 *** Sharp Key Return Spring (TP10MDF/s) 055101 * 4K7 X4 1/16w 5% Smd Resistor Array
030950 * 470u 16V 20% Low Esr Vert Electrolytic Capacitor 160213 *** Natural Key Return Spring (TP10MDF/s) 055100 * 100E X4 1/16w 5% Smd Resistor Array
030929 * 4u7 35V 20% Electrolytic Tantalium Capacitor 151226 *** Last C Key (TP10MDS) 011501 * 220pF x4 10% 100V NP0 Smd Capacitor Array
030880 * 10000uF 25V Snap-In Electrolytic Capacitor 151225 *** First A Key (TP10MDS) 011500 * 47pF x4 10% 100V NP0 Smd Capacitor Array
030856 * 4700uF 25V Snap-In Electrolytic Capacitor 151224 *** Sharp Key (TP10MDS) 010727 * 45.1584MHz Quartz Resonator
030555 * 4700u 50V 20% Snap-In Electrolytic Capacitor 151223 *** B Key (TP10MDS) 010704 * 16MHz Quartz Resonator
Note:
110020 T5A Fuse 5x20mm (EU) 151222 *** A Key (TP10MDS) 110282 * 3.6V 60mAh Nicd Battery Each spare part is single quantity unless otherwise specified.
110010 T2A Fuse 5x20mm (EU) 151221 *** G Key (TP10MDS) Asterisk prefix explanation:
110083 T2A Fuse 6.3x32mm (US) 151220 *** F Key (TP10MDS)
Outputs Assembly Omitted = First level spare part.
110021 T5A Fuse 6.3x32mm (US) 151219 *** E Key (TP10MDS) 730996 Outputs Assembly One asterisk = Second level, part of previous listed first level part.
151218 *** D Key (TP10MDS) 730995 * Outputs Board (Pcb#310608) Two asterisk = Third level, part of previous listed second level part.
Cabinet Speakers Assembly 151217 *** C Key (TP10MDS) 230569 ** FL5R200PNT EMI Coil For Signal Three asterisk = ............
770846 Cross-Over Cables Assembly 340092 * 5mm Board Spacer 230527 ** BL02RN2-R62 EMI Coil For Signal Any request for not above mentioned part must encompass specific
141107 * 4 Contacts Female Connector Housing 210017 * 2x10mm Adhesive Black Felt (specify mt) 141012 ** 8 Contacts Vert Female Connector description including:
141105 * Female Crimping Contact 141010 ** 4 Contacts Vert Female Connector 1) Model name,
140327 * 6 Contacts Hor Male Connector
Controls Panel Assembly 140918 ** 2 Contacts Hor Male Connector 2) Section name,
730994 Cross-Over Board (Pcb#310606) 820585 Controls Panel Assembly (Gem) 140908 ** 6 Contacts Vert Male Small Connector 3) Module code,
230533 * 0.45mH 1mm Crossover Coil 820584 Controls Panel Assembly (Baldwin) 140247 ** 8 Poles Mini Din Female Socket 4) Reference name,
141101 * 4 Contacts Vert Male Connector 810678 * Controls Panel & Display Board Assembly 140217 ** Jack Slim Horizontal S-F Socket 5) Quantity number.

J 20

Downloaded from www.Manualslib.com manuals search engine