CPC 100 PTM User Manual Enu

CPC 100 PTM
User Manual
CPC 100 PTM User Manual
Manual Version: ENU 1036 06 05

© OMICRON electronics GmbH 2017. All rights reserved.
This manual is a publication of OMICRON electronics GmbH.
All rights including translation reserved. Reproduction of any kind, for example, photocopying,
microfilming, optical character recognition and/or storage in electronic data processing systems,
requires the explicit consent of OMICRON. Reprinting, wholly or in part, is not permitted.
The product information, specifications, and technical data embodied in this manual represent the
technical status at the time of writing and are subject to change without prior notice.
We have done our best to ensure that the information given in this manual is useful, accurate and entirely
reliable. However, OMICRON does not assume responsibility for any inaccuracies which may be
present.
The user is responsible for every application that makes use of an OMICRON product.
OMICRON translates this manual from the source language English into a number of other languages.
Any translation of this manual is done for local requirements, and in the event of a dispute between the
English and a non-English version, the English version of this manual shall govern.
2 OMICRON
Contents
Contents
About this manual 6
Related documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Conventions and symbols used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1 Safety instructions 8
1.1 Operator qualifications and safety standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.2 Orderly measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.3 Disclaimer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.3.1 Automatic assessment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.3.2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2 System requirements 10
3 Introduction 11
3.1 The test set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.2 Installing Primary Test Manager. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.3 Starting Primary Test Manager and connecting to the CPC 100 . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.3.1 Starting via the PTM icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.3.2 Starting via the CPC Start Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.3.3 Connecting to the CPC 100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.3.4 Updating the CPC 100 embedded software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.3.5 Open the device web interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.4 Primary Test Manager licensing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4 Home view 17
4.1 Title bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.1.1 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.1.2 Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.1.3 About . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.2 Status bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.2.1 Connecting to a test system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.2.2 Manual connection to a test system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.3 Data backup and restoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.4 Data synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.4.1 Server settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.4.2 Managing subscriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4.4.3 Database synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
5 Jobs 34
5.1 Guided test workflow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
5.2 Job overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
5.2.1 Job data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
5.2.2 Approving jobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
5.2.3 Assessment summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
5.2.4 Managing attachments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
5.3 Location view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
5.3.1 Location data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
5.3.2 Setting the geo coordinates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
5.4 Asset view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
5.4.1 General asset data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
5.4.3 Transformer view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
5.4.4 Spare bushing view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
5.4.5 Circuit breaker view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
OMICRON 3
5.4.6 Current transformer view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

5.4.7 Voltage transformer view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
5.4.8 Rotating machine view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
5.4.9 Miscellaneous view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
5.5 Test view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
5.5.1 Selecting tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
5.5.2 Importing tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
5.5.3 Performing tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
5.5.4 Processing templates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
5.6 Handling results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
5.6.1 Trending tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
5.6.2 Assessing measurement results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
5.6.3 Comparing results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
6 Execute prepared job 74
7 Manage objects 75
7.1 Search for objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
7.2 Perform operations on objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
7.3 Master locations and assets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
7.4 Duplicate assets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
7.5 Relocate assets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
7.6 Import and export jobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
8 Create new manual tests 81
8.1 Add tests to a job . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
8.2 Processing tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
9 Open manual tests 83
10 Control tests 85
11 Generate test reports 86
12 Asset data 88
12.1 Transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
12.1.1 Bushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
12.1.2 Tap changer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
12.1.3 Surge arrester . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
12.2 Spare bushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
12.3 Circuit breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
12.3.1 Operating mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
12.3.2 Bushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
12.3.3 Assessment limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
12.4 Current transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
12.4.1 Common Parameters and settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
12.4.2 IEC 60044 protection CTs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
12.4.3 IEC 61869 protection CTs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
12.4.4 IEC 61869 metering CTs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
12.4.5 IEEE C57.13 protection CTs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
12.4.6 IEEE C57.13 metering CTs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
12.5 Voltage transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
12.6 Rotating machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
12.7 Grounding system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
13 Transformer tests 104
13.1 Two-winding transformers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
13.1.1 Oil analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
13.1.2 Overall PF/DF/Tanδ & CAP test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
13.1.3 Bushing H/X PF/DF/Tanδ & CAP – C1 test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
4 OMICRON
Contents
13.1.4 Bushing H/X PF/DF/Tanδ & CAP – C2 test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

13.1.5 Bushing H/X – energized collar test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
13.1.6 Exciting current test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
13.1.7 Insulating fluids PF/DF/Tanδ & CAP test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
13.1.8 Surge arrester watt losses H/X test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
13.1.9 Leakage reactance H-X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
13.1.10 Zero Sequence Impedance H/X test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
13.1.11 TTR H–X test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
13.1.12 DC Winding Resistance H/X test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
13.1.13 Dynamic OLTC-Scan (DRM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
13.1.14 Demagnetization test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
13.2 Three-winding transformers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
13.3 Autotransformers without tertiary winding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
13.4 Autotransformers with tertiary winding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
13.5 Voltage regulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
14 Spare Bushing tests 151
14.1 Spare Bushing PF/DF/Tanδ & CAP – Overall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
14.2 Spare Bushing PF/DF/Tanδ & CAP – C1 test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
14.3 Spare Bushing PF/DF/Tanδ & CAP – C2 test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
14.4 Spare Bushing PF/DF/Tanδ & CAP – C1+C2 test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
14.5 Spare Bushing – Energized Collar test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
15 Circuit breaker tests 163
15.1 Circuit Breaker PF/DF/Tanδ & CAP test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
15.2 Bushing PF/DF/Tanδ & CAP – C1 test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
15.3 Bushing PF/DF/Tanδ & CAP – C2 test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
15.4 Bushing – Energized Collar test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
15.5 Insulating Fluids PF/DF/Tanδ & CAP test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
15.6 Contact Resistance test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
16 Current transformer tests 175
16.1 CT PF/DF/Tanδ & CAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
16.2 CT Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
16.3 CT Winding Resistance Sec. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
16.4 CT Excitation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
16.5 CT Ratio V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
16.6 CT Burden . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
16.7 CT Composite Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
17 Voltage transformer tests 187
17.1 VT PF/DF/Tanδ & CAP test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
17.2 VT Ratio test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
17.3 VT Burden test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
18 Rotating machine tests 189
18.1 Stator Winding PF/DF & CAP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
19 Grounding system tests 192
19.1 Ground impedance measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
19.2 Step&Touch voltage measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
20 Optional manual tests 194
20.1 Insulation Resistance test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
20.2 TanDelta – PF/DF/Tanδ & CAP test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
Support 200
OMICRON 5
About this manual

This manual provides information on how to use Primary Test Manager safely, properly and efficiently.
The CPC 100 PTM User Manual gets you familiar with operating Primary Test Manager and guides you
step by step through the test procedures with the OMICRON test systems.
This manual and the technical documentation shipped with the test systems always have to be available
on the site where Primary Test Manager is used. Read all manuals carefully before using Primary Test
Manager and observe the safety, installation, and operation instructions therein. Reading this manual
alone does not release you from the duty to comply with all national and international safety regulations
relevant to working on the high-voltage equipment.
Note: This User Manual describes Primary Test Manager with all available features. Please note that
the features are only available if you have bought corresponding license keys. For more information, see
3.4 "Primary Test Manager licensing" on page 16.
Related documents
The following documents complete the information covered in this manual.
Title Description
CPC 100 User Manual Contains safety and operation instructions on the CPC 100
test system.
CPC 100 Reference Manual Contains detailed hardware and software information on the
CPC 100 including relevant safety instructions.
CP TD1 Reference Manual Contains hardware and software information about the
CP TD1 test system.
CP SB1 User Manual Contains hardware and software information about the
CP SB1 transformer switch box.
6 OMICRON
About this manual
Conventions and symbols used

In this manual, the following symbols indicate safety instructions for avoiding hazards.
DANGER
Death or severe injury will occur if the appropriate safety instructions are not observed.
WARNING
Death or severe injury can occur if the appropriate safety instructions are not observed.
CAUTION
Minor or moderate injury may occur if the appropriate safety instructions are not
observed.
NOTICE
Equipment damage or loss of data possible
OMICRON 7
1 Safety instructions
Before operating Primary Test Manager and the test set, read the following safety instructions carefully.
When testing with Primary Test Manager, observe the safety rules in this chapter and all relevant safety
instructions in the technical documentation shipped with the test systems. Do not turn on or operate the
CPC 100 if you do not fully understand the safety information. If you have any questions regarding the
safety instructions, contact OMICRON before proceeding.
Before connecting any test leads to a test object, always observe the five safety rules:
► Disconnect completely
► Secure from reconnection
► Verify that the installation is dead
► Carry out grounding and short-circuiting
► Provide protection against adjacent live parts
Safety accessories
OMICRON offers a range of accessories for added safety during the operation of our test systems. For
further information and specifications, refer to the corresponding Supplementary Sheet or contact
OMICRON Support (see "Support" on page 13).
1.1 Operator qualifications and safety standards

Working on the high-voltage equipment can be extremely dangerous. Consequently, only qualified,
skilled, and authorized personnel is allowed to test with Primary Test Manager. Before starting to work,
clearly establish the responsibilities. Personnel receiving training, instructions, directions, or education
on Primary Test Manager must be under constant supervision of an experienced operator while working
on the high-voltage equipment.
Testing with Primary Test Manager must comply with the following safety standards:
• EN 50191 (VDE 0104) "Erection and Operation of Electrical Test Equipment"
• EN 50110-1 (VDE 0105 Part 100) "Operation of Electrical Installations"
• IEEE 510 "IEEE Recommended Practices for Safety in High-Voltage and High-Power Testing"
Moreover, observe all relevant national and international regulations for accident prevention.
1.2 Orderly measures

This manual and the technical documentation shipped with the test systems always have to be available
on the site where Primary Test Manager is operated. The users of Primary Test Manager must read all
relevant documentation before operating Primary Test Manager and observe the safety, installation, and
operation instructions therein.
Primary Test Manager may be used only as described in this manual. Any other use is not in accordance
with the regulations. The manufacturer and the distributor are not liable for damage resulting from
improper usage. The user alone assumes all responsibility and risk. Full compliance with the regulations
also includes following the instructions provided in this manual.
8 OMICRON
Safety instructions
1.3 Disclaimer
1.3.1 Automatic assessment
The applied auto-assessment rules (for example, indicated colors, indications) and limits within the
Program are defined according to industry standards and/or are based on the experience of industry
experts. The purpose of the auto-assessment is to indicate to the person that uses the Program – "User"
any deviation of the measured parameters from the expected values based on the recommended limits
provided by OMICRON or defined by the User. Any decision to return the apparatus to service or remove
the apparatus from service cannot be based on the results of the auto-assessment alone. This decision
is the sole responsibility of the owner or end user of the apparatus.
1.3.2 Safety
If Primary Test Manager and the test set are used in a manner not specified by the manufacturer, the
protection provided by the test systems may be impaired.
OMICRON 9
2 System requirements
Table 2-1: Primary Test Manager system requirements
Characteristic Requirement (*recommended)

Operating system Windows 10 64-bit*
Windows 8.1 64-bit*,
Windows 8 64-bit*,
Windows 7 SP1 64-bit* and 32-bit
CPU Multicore system with 2 GHz or faster*,
single-core system with 2 GHz or faster
RAM min. 2 GB (4 GB*)
Hard disk min. 4 GB of available space
Storage device DVD-ROM drive
Graphics adapter Super VGA (1280×768) or higher-resolution video adapter and monitor1
Interface Ethernet NIC2,
USB 2.03
Installed software Microsoft Office 2016*, Office 2013, Office 2010, Office 2007
required for the optional
Microsoft Office
interface functions
1. We recommend graphics adapter supporting Microsoft DirectX 9.0 or later.
2. For testing with TESTRANO 600, CPC 100 and CIBANO 500. NIC = Network Interface Card.TESTRANO 600, CPC 100 and
CIBANO 500 can be connected with RJ-45 connectors either directly to the computer or to the local network, for example, by
using an Ethernet hub.
3. For testing with FRANEO 800
10 OMICRON
Introduction
3 Introduction
Primary Test Manager is a management tool for testing primary assets such as power transformers,
circuit breakers, and current transformers with the OMICRON test systems. Primary Test Manager
provides a computer interface to the test set, controls the automated test procedures, and facilitates
testing of primary assets by guiding you through the test workflow.
Primary Test Manager uses the concept of jobs. A job contains all relevant information about the
location, the asset under test, and the tests. With Primary Test Manager, you can process jobs as
separate entities.
With Primary Test Manager, you can create new jobs, manage locations, assets, jobs, and reports, and
execute prepared jobs. For a specified job, you can make measurements on the asset under test by just
pressing the I/0 button on the front panel of the CPC 100 test system. After you have performed a test,
you can generate exhaustive test reports. Primary Test Manager runs on a computer and communicates
with the test set through the Ethernet connection.
OMICRON 11
3.1 The test set

Primary Test Manager controls the test set consisting of the CPC 100 multifunctional test system, the
CP TD1 capacitance and power/dissipation factor measuring instrument, and the CP SB1 transformer
switch box.
I/0 button
Figure 3-1: Front view of the CPC 100
Network connector
Figure 3-2: Right-side view of the CPC 100
For detailed information about the test set, see the technical documentation shipped with the CPC 100,
CP TD1, and CP SB1 test systems.
12 OMICRON
Introduction
3.2 Installing Primary Test Manager

For the minimum requirements your computer needs to run the Primary Test Manager software, see
2 "System requirements" on page 10.
To install Primary Test Manager:
1. Connect the computer’s Ethernet port to the network connector of the CPC 100 test system using an
Ethernet cable.
Note: You can operate Primary Test Manager without connection to the CPC 100. To perform tests,
the computer running Primary Test Manager must be connected to the CPC 100.
2. Switch on the CPC 100.
3. Put the Primary Test Manager DVD in the DVD drive of your computer and follow the instructions on
the screen.
Note: Upgrade your CPC 100 during the installation, if necessary.
OMICRON 13
3.3 Starting Primary Test Manager and connecting to the

CPC 100
3.3.1 Starting via the PTM icon
To start Primary Test Manager via the Windows Start menu, click Start on the task bar, then click
OMICRON Primary Test Manager, or double-click the OMICRON Primary Test Manager icon on
the desktop.
3.3.2 Starting via the CPC Start Page

To start Primary Test Manager via the CPC Start Page, complete the following steps:
1. Double-click the CPC Start Page icon on the desktop.
Figure 3-3: CPC start page
2. On the CPC start page, select the CPC 100 device to which you want to connect.
3. Under Tools, click Primary Test Manager.
14 OMICRON
Introduction
3.3.3 Connecting to the CPC 100

► To connect to CPC 100, select the device from the list on the CPC Start Page (see Figure 3-3 above)
or in the PTM Home view.
► In Primary Test Manager click Connect after selecting the device.
Figure 3-4: Connecting to CPC 100
If you were not able to connect to your CPC 100 device and the green light is permanently on, wait a few
seconds, and then do one of the following:
► Click More (under the Connect button), then click Refresh.
► Press F5.
If the CPC 100 device to which you want to connect is not displayed in the list of available devices,
proceed as described in4.2.2 "Manual connection to a test system" on page 29.
Alternatively, you can manage the connection to CPC 100 in the Primary Test Manager status bar (see
4.2 "Status bar" on page 28).
3.3.4 Updating the CPC 100 embedded software

The CPC 100 embedded software must be compatible with the Primary Test Manager software. You can
update the CPC 100 embedded software by using one of the following procedures.
Updating via PTM Home view

To update the CPC 100 embedded software in the Primary Test Manager home view:
1. In the home view, select the device you want to update from the list.
2. Click More beneath the Connect button, and then click Update device software.
3. In the Select CPC Upgrade Image dialog box, double-click the UpgradeV1.upg file.
► Alternatively, select the device you want to update from the list, and then click Connect. Primary Test
Manager will prompt you to update the CPC 100 embedded software, if necessary.
OMICRON 15
Updating via device browser

To update the CPC 100 embedded software by using the device browser:
1. Exit Primary Test Manager if it is running.
2. Double-click the OMICRON Devices icon on the desktop.
3. In the OMICRON Devices window, right-click the CPC 100 device you want to update, and then click
Upgrade device to open the file selection dialog.
4. You can find the upload file:
• On the Primary Test Manager DVD at
.\_EmbeddedSoftware\CPC100\V1 device\UpgradeV1.upg
• On the hard disk of your computer at
C:\Program Files (x86)\Common Files\OMICRON\UpgradeImages\CPC100\UpgradeV1.upg
5. After the update has finished, CPC 100 reboots automatically.
6. Restart Primary Test Manager after the update procedure has finished.
3.3.5 Open the device web interface

On the device website, you can upgrade the device embedded software, get log files, roll back software
images, reboot the device and manage license files.
To open the device web interface:
1. In the home view, select the device from the list.
2. Click More beneath the Connect button, and then click Open device web interface.
A website with the IP address of the device opens in the default web browser.
3.4 Primary Test Manager licensing

The following table describes the Primary Test Manager licensing.
Table 3-1: Primary Test Manager licenses
License Description
PTM Standard Manual control mode with tests according to your CPC 100 license.
Additional 30 testing days with guided workflow according to your
CPC 100 license.
PTM Advanced Timely unlimited testing with guided workflow and manual tests according
to your CPC 100 license.
The PTM Advanced license key is on the CPC 100. You need to upgrade your CPC 100 on the CPC
start page (see Figure 3-3: "CPC start page" on page 14).
For detailed information, contact your OMICRON local sales representative or distributor.
16 OMICRON
Home view
4 Home view
After starting Primary Test Manager, the home view opens. In the home view, you can select different
user tasks designed to support you during diagnostic testing and management of test objects and test
data.
Figure 4-1: Primary Test Manager home view
Primary Test Manager processes data of different workflow importance. This is indicated by balloons of
different categories as described in the following table.
Table 4-1: Data importance categories
Balloon Category Description

Mandatory Indicates data required for performing tests.
Recommended Indicates data supporting the Primary Test Manager workflows.
Information Contains descriptive information.
OMICRON 17
Primary Test Manager supports the following user tasks.

Table 4-2: Selecting the user tasks
Button Description Action
Click to start the guided test workflow

Create new job
(see 5 "Jobs" on page 34).
Click to execute a prepared job

Execute prepared job
(see 6 "Execute prepared job" on page 74).
Click to open the Manage view for locations, assets, jobs,

Manage and reports
(see 7 "Manage objects" on page 75).
Click to create a new manual test

Create new manual tests
(see 8 "Create new manual tests" on page 81)
Click to open a manual test

Open manual tests
(see 9 "Open manual tests" on page 83)
18 OMICRON
Home view
4.1 Title bar

Note: The title bar is displayed in any Primary Test Manager view.
The following table describes the title bar commands.
Table 4-3: Title bar commands
Command Action
Home Click Home to move from any view to the home view.
Synchronize1 Click Synchronize to synchronize your local database with the Primary
Test Manager server database
(see 4.4 "Data synchronization" on page 31).
Settings Click Settings to open the Settings dialog box
(see 4.1.1 "Settings" later in this chapter).
Help Click Help to open the CPC 100 technical documentation and send data
to OMICRON Technical Support
(see 4.1.2 "Help" on page 27).
About Click About to open the About Primary Test Manager dialog box
(see 4.1.3 "About" on page 27).
1. Only enabled with the appropriate license.
4.1.1 Settings
In the Settings dialog box, you can make a number of Primary Test Manager settings to match your
regional conventions, manage the job templates, and set the Primary Test Manager server settings for
data synchronization (see 4.4 "Data synchronization" on page 31). To open the Settings dialog box,
click Settings in the title bar.
NOTICE
Changing the settings in the Settings dialog box affects all data in Primary Test Manager.
► Only change settings if you are qualified to do so.
► Review your changes before clicking OK.
Note: After changing a setting, you must restart Primary Test Manager for the setting to take effect.
OMICRON 19
General
The General tab lists the general settings of Primary Test Manager.
Figure 4-2: General tab
► To set the Primary Test Manager language, select your preferred language from the Language list.
► To set the logging level, select your preferred level from the Logging PTM and Logging Device lists.
The logging function provides information to help find the cause for an error in cooperation with an
OMICRON support engineer. Logging PTM collects information on PTM while Logging Device
focuses on your device.
Note: Log files do not contain any personal information.
Table 4-4: Logging levels
Logging level Description

Disabled Logging is disabled.
Errors only Only errors are logged.
Recommended setting
Info Errors and some additional information are logged.
Full All software-related activities are logged.
Note: Full logging will slow down software performance.
► To set the types of available devices, select the respective check boxes.
Under Location settings, you can activate the Use location information check box for Grounding
system tests (see 19 "Grounding system tests" on page 192).
20 OMICRON
Home view
Under Default test device configuration, Primary Test Manager displays the default devices for testing
different assets. If more than one device is available for an asset, you can set your preferred test system
as default device for that asset.
Note: If no device is connected, Primary Test Manager will automatically compile the test list (see
section 5.5 "Test view" on page 59) for the selected default test set.
The Customer Experience Improvement Program collects information about how you use Primary
Test Manager without interrupting you. This helps OMICRON identify which features to improve. No
information collected is used to identify or contact you. We encourage you to join the program to help
improve Primary Test Manager.
Profiles
In the Profiles tab, you can set your profile, the default rated frequency, the loss index, the units of your
own profiles, and make the test system settings.
Figure 4-3: Profiles tab
With Primary Test Manager, you can use predefined profiles and create your own profiles for naming
conventions.
Note: Primary Test Manager sets the default profile according to the regional settings of your computer.
► To set a profile, select the profile you want to use from the Profiles list.
To create your own profile:
1. Click Create custom profile.
2. In the Create custom profile dialog box, type the profile name, and then click Create.
3. Under Global settings, set the default rated frequency, the loss index, and your preferred units.
OMICRON 21
Profiles: Transformer
4. Under Transformer, set the transformer terminal name schemes and preferences such as the
names of some tests, the oil measure, and the short-circuit impedance abbreviation.
Figure 4-4: Profiles tab: Transformer
With Primary Test Manager, you can use predefined transformer naming conventions according to the
established standards and create your own terminal name schemes.
► To set a terminal names scheme, select the scheme you want to use from the
Terminal names scheme list.
To create your own terminal names scheme:
a) Click Create custom scheme.
b) In the Enter scheme name dialog box, type the scheme name.
c) Set the transformer terminal names, scheme options, and preferences.
► To delete your own terminal name scheme, select the scheme from the Terminal names scheme
list, and then click Delete current scheme.
22 OMICRON
Home view
Profiles: Circuit breaker

5. Under Circuit breaker, set the circuit breaker terminal name schemes.
Figure 4-5: Profiles tab: Circuit breaker
OMICRON 23
Profiles: Current transformer

6. Under Current transformer, set the current transformer naming conventions.
Figure 4-6: Profiles tab: Current transformer
7. Click OK to close the Settings dialog box.

► To delete your own profile, select the profile from the Profiles list, and then click
Delete current profile.
24 OMICRON
Home view
Templates
In the Templates tab, you can edit, import and export job templates for transformers.
► For information on how to process the templates, see 5.5.4 "Processing templates" on page 68.
Figure 4-7: Templates tab
The right pane of the template workspace displays the template preview.
To manage the job templates, select Transformer from the Display templates for list, and then do one
of the following:
► To assign a template to a different asset type or a phase group, or to edit template properties (name,
comment), click the respective Edit button.
► Press the Delete button to delete templates from the Asset type or Phases list.
► To export a template, select the template, and click the Export button.
► To import a template, click the Import button, then browse to the template you want to import.
► To set a template as favorite, click the star icon .
Note: All future test lists with the same asset and number of phases will by default be loaded with the
tests defined in this favorite template.
OMICRON 25
Databases
In the Databases tab you can create, manage and switch between different databases for Primary Test
Manager. Under Properties, you can edit the database name and adjust the server settings for
DataSync. For more information, see 4.4.1 "Server settings" on page 31.
Figure 4-8: Databases tab
26 OMICRON
Home view
4.1.2 Help
In the Help dialog box, you can get the relevant information about CPC 100 and data synchronization,
and send data to OMICRON Technical Support. To open the Help dialog box, click Help in the title bar.
Figure 4-9: Help dialog box
4.1.3 About
In the About Primary Test Manager dialog box, you can enter a license key to upgrade your Primary
Test Manager and enhance its functionality by installing additional features. To open the
About Primary Test Manager dialog box, click About in the title bar.
Figure 4-10: About Primary Test Manager dialog box
OMICRON 27
To activate a license, enter the license key in the About Primary Test Manager dialog box, and then
click Add license key. For detailed information about the Primary Test Manager licensing, contact your
OMICRON local sales representative or distributor.
4.2 Status bar

Note: The status bar is displayed in any Primary Test Manager view.
The status bar displays information about the status of the test system and provides access to the zoom
function.
The following table describes the statuses of the test system.
Table 4-5: Test system statuses

Icon Status
CPC 100 connected
CPC 100 not connected
CP SB1 connected
CP SB1 not connected
CP TD1 connected
CP TD1 not connected
In the status bar, you can connect to and disconnect from a test system, and show and refresh the test
set information.
4.2.1 Connecting to a test system

To connect to a test system:
1. Right-click the CPC 100 icon in the status bar, and then click Connect.
Figure 4-11: Connect to device dialog box
2. In the Connect to device dialog box, select the test system from the list, and then click Connect.
28 OMICRON
Home view
If you could not connect to your CPC 100 device and the green light is permanently on, wait a few
seconds, and then proceed as follows:
1. Click More beneath the Connect button.
2. Click Refresh.
3. In the Connect to device dialog box, select the test system from the list, and then click Connect.
After you have connected to the test system, the following dialog box appears.
Figure 4-12: Connected to device dialog box
After you have connected to a test system, right-click the CPC 100 icon in the status bar, and then do
one of the following:
► To disconnect from a test system, click Disconnect.
► To display information about the connected test system, click Show test set information.
► To update the test set information, click Refresh test set information.
Note: You can open the Connect to device and the Connected to device dialog boxes also by double-
clicking the CPC 100 icon.
4.2.2 Manual connection to a test system

If you encounter any problems when connecting to the CPC 100 we recommend turning off any wireless
adapter and VPN software on your computer.
If the CPC 100 device to which you want to connect is not displayed in the list of available devices,
proceed as follows:
1. Click the Start OMICRON Device Browser button .
2. In the OMICRON Device Browser window, look for the device you want to connect to and read its
IP address.
3. In the home view, click More beneath the Connect button, and then click Add device manually.
4. In the Add Device Manually dialog box, type the IP address of the device you want to connect to.
5. Click Connect.
If you assigned a static IP address to the device, you can try to connect as follows:
1. In the Add Device Manually dialog box, select the Direct connection check box.
OMICRON 29
2. In the Host or IP box, type cpc://a.b.c.d, where a.b.c.d is the static IP address of the device.
4.3 Data backup and restoring

We strongly recommend backing up your data in the Primary Test Manager database on a regular basis.
Primary Test Manager reminds you to back up the data periodically by prompting you to save the data
in your preferred location. The Primary Test Manager data is backed up in DBPTM format.
To back up the data without the Primary Test Manager prompt:
1. In the home view, click Back up your data.
Figure 4-13: Primary Test Manager home view
2. Save the data in your preferred location.

To restore the data:
1. In the home view, click Restore data from a backup.
2. Browse to the file you want to restore.
30 OMICRON
Home view
4.4 Data synchronization

Primary Test Manager comes with the client/server architecture. With this feature, you can synchronize
your local database with the Primary Test Manager server database.
Note: To synchronize your data, you need a license. To get the license, contact your regional OMICRON
Service Center or sales partner. You can find our Service Center or sales partner closest to you at
www.omicronenergy.com.
The data synchronization is partial data replication based on subscriptions, that is, all local data is
synchronized with the server database and selected data on the server is synchronized with the local
database.
4.4.1 Server settings

Before synchronizing the Primary Test Manager databases for the first time, you need to set the server
settings.
1. In the title bar, click Settings and select the Databases tab.
The next step depends on the data synchronization method you use: DataSync via web server or
DataSync on premises.
Figure 4-14: Server settings for DataSync
DataSync via web server

► For the service URL and certificate for DataSync via web server, contact your regional OMICRON
Service Center.
OMICRON 31
DataSync on premises
► For the service URL and certificate for DataSync on premises, contact your system administrator.
2. In the Databases tab, enter the Service URL and upload the Certificate.
3. To test the connection to the server, click Test next to the Connection status.
4.4.2 Managing subscriptions

You can select data on the server which you want to synchronize with your local data by managing
subscriptions. To manage subscriptions:
1. In the home view (see Figure 4-1: "Primary Test Manager home view" on page 17), click the Manage
button .
Figure 4-15: Manage view
2. In the manage view, click Manage subscriptions on the top of the workspace.
3. In the Subscriptions dialog box, select the data on the server you want to synchronize with your local
data.
You can synchronize the data anytime.
► To synchronize the data, click Synchronize in the title bar.
After that, Primary Test Manager shows the synchronization progress.
32 OMICRON
Home view
4.4.3 Database synchronization

► To synchronize the local Primary Test Manager database with the server database, click
Synchronize in the title bar of the Manage view.
Primary Test Manager then displays the synchronization progress.
Note: You can synchronize databases at any time, as long as a connection to the server database is
available.
When the database synchronization is complete, the locations, assets, and jobs (objects) newly added
to the local database are marked with blue dots in the manage view. You can sort the objects by this
column. As soon as you open an object, its blue dot is removed. All blue dots are removed when you
perform another database synchronization.
OMICRON 33
5 Jobs
When creating a new job, Primary Test Manager leads you through the guided test workflow. To open
the create new job view, click the Create new job button in the home view.
Figure 5-1: Create new job view
In the create new job view, you can configure and execute jobs. A job contains all relevant information
about the location, the asset under test, and the tests. With Primary Test Manager, you can process jobs
as separate entities. During the guided test workflow, the job status displayed in the left pane of the
create new job view changes. The following table describes the job statuses.
Table 5-1: Job statuses
Status Description
New Location has been defined.
Prepared Asset has been defined.
Partially executed At least one measurement has been executed.
Executed All tests of the job have been executed.
Approved Job has been approved.
34 OMICRON
Jobs
5.1 Guided test workflow

The guided test workflow leads you through the following steps:
1. Enter the job data (see 5.2 "Job overview" on page 36).
2. Specify the location (see 5.3 "Location view" on page 38).
3. Specify the asset (see 5.4 "Asset view" on page 42).
4. Specify and perform the tests (see 5.5 "Test view" on page 59).
5. Generate the test reports (see 11 "Generate test reports" on page 86).
To navigate through the test workflow, click the navigation buttons in the left pane of the create new job
view.
Figure 5-2: Navigation buttons
Note: You can anytime interrupt the test workflow and return to any view by clicking the corresponding
navigation button.
By using the commands on the menu bar, you can process jobs. The following table describes the
available operations.
Table 5-2: Operations on the jobs
Command Action
Close Closes a job displayed in the create new job view and leads you back to
home or manage view respectively.
Save job Saves the job displayed in the create new job view.
Copy test Adds another test of the same kind and with the same settings to the test
list. Results are not copied.
Take screenshot Takes screenshot of the selected area of the Primary Test Manager
workspace. The screenshot appears as attachment in the General area
and can be attached to the test report (see 11 "Generate test reports" on
page 86).
For more information about operations on the jobs, see 7 "Manage objects" on page 75.
OMICRON 35
5.2 Job overview

In the job overview of the create new job view, you can enter the job data (see Table 5-3: "Job data" on
page 36). In the course of the guided test workflow, Primary Test Manager sets also some basic location,
asset, and test data. To open the job overview, click the Create new job button in the home view.
Figure 5-3: Job overview
5.2.1 Job data

The following table describes the job data.
Table 5-3: Job data
Data Description
Name/WO1 Name of the job or work order
(by default generated by Primary Test Manager)
Creation date Date the job was created
Execution date Date the job was executed
Tested by Person who performed the test
Approved by Person who approved the test
Approval date Date the job was approved (see 5.2.2 "Approving jobs" later in this
section)
1. Mandatory data
36 OMICRON
Jobs
5.2.2 Approving jobs

If the job data displayed in the job overview has been approved, you can set the approval date of the job.
To set the job approval date, click Approve.
Note: After approving a job, some settings cannot be edited anymore.
5.2.3 Assessment summary

In the Tests area of the job overview, the Result state and Assessment status of test results are
displayed.
► Use the Overall Assessment combo box to manually characterize the asset's condition for reporting
purposes.
Table 5-4: Assessment statuses in the job overview
Status Description
Fail The status was automatically set to Fail by Primary Test Manager.
Manual fail The status was manually set to Fail.
Investigate The status was automatically set to Investigate by Primary Test
Manager.
Manual investigate The status was manually set to Investigate.
Pass The status was automatically set to Pass by Primary Test Manager.
Partial pass Some measurements have not been assessed.
Manual pass The status was manually set to Pass.
Manual partial pass Some measurements have not been assessed and at least one
assessment status was changed manually.
Not assessed The measurement has not been assessed.
Not rated The status was automatically set to Not Rated by Primary Test
Manager.
OMICRON 37
5.2.4 Managing attachments

Under Attachments, you can manage attachments to the job overview.
To add an attachment to the job overview:
1. Click the Add button .
2. In the Select Files dialog box, browse to the file you want to attach to the job overview.
To open an attachment, do one of the following:
► Select the attachment, and then click the Open button .
► Double click the attachment.
To delete an attachment from the job overview:
1. Select the attachment you want to delete.
2. Click the Remove button .
5.3 Location view

In the location view of the create new job view, you can specify locations. To open the location view, click
the Location navigation button .
Figure 5-4: Location view
38 OMICRON
Jobs
To specify a location, do one of the following:

► Enter the location data (see Table 5-5: "Location data" on page 39).
Note: If you enter location or asset data for a prepared job that differ from those of the master location
or master asset, a notification bar will be displayed. In this case, choose between the following options:
► To import the previously defined location or asset data to this job, click Import from master
location or Import from master asset in the notification bar.
► To update the previously defined location or asset data with the data you have entered for this job,
click Update master location or Update master asset in the notification bar.
► For more information on operations on the jobs, see 7 "Manage objects" on page 75.
► To load the location data available in Primary Test Manager, click Load existing location, and then
select the location you want to load in the Select Location dialog box.
Figure 5-5: Select Location dialog box
In the Select Location dialog box, you can search for locations (see 7.1 "Search for objects" on
page 76).
5.3.1 Location data

The following table describes the location data.
Table 5-5: Location data
Data Description
Name1 Name of the location
Region Region where the asset is located
Division Division where the asset is located
Area Area where the asset is located
Plant Plant where the asset is located
OMICRON 39
Table 5-5: Location data (continued)
Data Description
Address Address of the location
City City where the asset is located
State/Province State or province where the asset is located
Postal code Postal code of the location
Country Country where the asset is located
Geo coordinates Geo coordinates of the location
(see 5.3.2 "Setting the geo coordinates" later in this section)
Location system code Location code used by maintenance planning systems
Contact Person
Name Name of the contact person
Phone no. 1 Phone number of the contact person
Phone no. 2 Alternative phone number of the contact person
E-mail E-mail address of the contact person
Company
Company Company where the asset is located
Department Department of the company
Address Address of the company
City City where the company is located
State/Province State or province where the company is located
Postal code Postal code of the company
Country Country where the company is located
Phone no. Phone number of the contact person
Fax no. Fax number of the contact person
E-mail E-mail address of the contact person
1. Mandatory data
In the location view, you can enter additional addresses of, for example, a client, owner or utility. To enter
additional addresses, click Add address under Additional addresses. For the additional address data,
see Table 5-5: "Location data" on page 39.
40 OMICRON
Jobs
5.3.2 Setting the geo coordinates

To set the geo coordinates of a location:
1. In the location view, click Edit coordinates.
Figure 5-6: Edit Coordinates dialog box
2. In the Edit Coordinates dialog box, enter the latitude and longitude of the location.

Under Attachments, you can manage attachments to locations.
To add an attachment to a location:
2. In the Select Files dialog box, browse to the file you want to attach to the location.
To delete an attachment from a location:
OMICRON 41
5.4 Asset view

In the asset view of the create new job view, you can specify assets. To open the asset view, click the
Asset navigation button .
Figure 5-7: Asset view
The asset view depends on the asset you want to specify with Primary Test Manager. To specify an
asset, do one of the following:
► Enter the asset data. The asset data includes the general asset data common to all assets (see
5.4.1 "General asset data" on page 43 and the asset-specific data described in chapter 12 "Asset
data" on page 88).
Note: If you enter location or asset data for a prepared job that differ from those of the master location
or master asset, a notification bar will be displayed. In this case, choose between the following options:
► To import the previously defined location or asset data to this job, click Import from master
location or Import from master asset in the notification bar.
► To update the previously defined location or asset data with the data you have entered for this job,
click Update master location or Update master asset in the notification bar.
► For more information on operations on the jobs, see 7 "Manage objects" on page 75.
42 OMICRON
Jobs
► To load the asset data available in Primary Test Manager, click Load existing asset, and then select
the asset you want to load in the Select Asset dialog box.
Figure 5-8: Select Asset dialog box
In the Select Asset dialog box, you can search for assets (see 7.1 "Search for objects" on page 76) and
sort them alphabetically or in the chronological order.
5.4.1 General asset data

The following table describes the general asset data.
Table 5-6: General asset data
Data Description
Asset1 Asset under test
Asset type Type of the asset
Serial no.1 Serial number of the asset
Manufacturer Manufacturer of the asset
Manufacturer type Type of the asset according to the manufacturer
Manufacturing year Year of the asset’s manufacturing
Asset system code Code of the asset used by the maintenance planning systems
Apparatus ID Identifier of the asset
Feeder Feeder the asset is connected to
Phase2 Phase the asset is connected to
1. Mandatory data
2. Only available for current transformers, voltage transformers and miscellaneous assets.

Under Attachments, you can manage attachments to assets.
OMICRON 43
To add an attachment to an asset:

2. In the Select Files dialog box, browse to the file you want to attach to the asset.
To delete an attachment from an asset:
5.4.3 Transformer view

In the transformer view, you can specify transformers and assets associated with the transformer such
as bushings, tap changers, and surge arresters.
To specify a transformer:
1. From the Asset list, select Transformer.
2. From the Asset type list, select the type of the transformer.
Figure 5-9: Transformer view
3. In the transformer view, enter the general asset data (see Table 5-6: "General asset data" on
page 43).
44 OMICRON
Jobs
4. Under Winding configuration, set the transformer’s vector group (see "Setting the vector group"
later in this section).
5. Under Ratings, Impedances and Others, enter the transformer data (see 12.1 "Transformer" on
page 88).
6. Optionally, specify the bushing mounted on the transformer (see "Bushings tab (Transformer)" on
page 47).
7. Optionally, specify the tap changers of the transformer (see "Tap changers tab" on page 48).
8. Optionally, specify the surge arresters mounted on the transformer (see "Surge arresters tab" on
page 49).
OMICRON 45
Setting the vector group

To set the vector group of a transformer:
1. Select the number of transformer’s phases.
2. Do one of the following:
► Select the configuration of the transformer’s windings from the respective lists.
► Click Select Winding Configuration and in the Edit vector group dialog box, set the
transformer’s vector group.
Figure 5-10: Edit vector group dialog box
Note: Primary Test Manager sets the vector group of an autotransformer without tertiary winding
automatically.
46 OMICRON
Jobs
Bushings tab (Transformer)

On the Bushings tab, you can specify the bushings mounted on the transformer.
Figure 5-11: Transformer view: Bushings tab
Specifying a bushing
1. From the Asset type list, select the type of the bushing.
2. Enter the bushing data (see 12.2 "Spare bushing" on page 91).
Under Copy bushing data, you can copy data of a bushing to other bushings. To copy the bushing data,
select the respective bushings from the From and To lists, and then click Copy.
OMICRON 47
Tap changers tab

On the Tap changers tab, you can specify the tap changers of the transformer.
Figure 5-12: Transformer view: Tap changers tab
Specifying an on-load tap changer (OLTC)

1. Select the OLTC check box.
2. Enter the OLTC data (see 12.1.2 "Tap changer" on page 90).
3. Under Tap changer configuration, set the tap changer’s winding, the tap scheme, and the number
of taps.
4. In the Voltage table you can either enter each value manually or have them calculated.
Click Calculate for the voltage table calculation and use one of the three methods:
– First and second: Calculation based on the voltages of the first and second tap
– Middle: Calculation based on the middle tap (rated voltage) and the entered deviation value
In the guided workflow, this value is automatically transferred from the Voltage ratings table
under Asset data – Transformer.
– First/middle/last: Calculation based on the voltages of the first, middle and last tap
Note: Middle and First/middle/last are only available for odd tap numbers.
► After calculation, compare the calculated values with the nominal values on the nameplate.
48 OMICRON
Jobs
Specifying a de-energized tap changer (DETC)

1. Select the DETC check box.
2. Enter the DETC data (see 12.1.2 "Tap changer" on page 90).
3. Under Tap changer configuration, set the tap changer’s winding, the tap scheme, the number of
taps, and the current tap position.
4. Type the voltage of all taps.
To add a tap, select the tap below which you want to add a tap, and then click Add.
Note: The added taps match no tap scheme.
► To delete a tap, select the tap you want to delete, and then click Delete.
► To delete all taps, click Remove all.
Surge arresters tab

On the Surge arresters tab, you can specify the surge arresters mounted on the transformer.
Figure 5-13: Transformer view: Surge arresters tab
Specifying a surge arrester

1. Select the respective Surge arrester check box.
2. Enter the surge arrester data (see 12.1.3 "Surge arrester" on page 90).
Under Copy surge arrester data, you can copy data of a surge arrester to other surge arresters. To
copy the surge arrester data, select the respective surge arresters from the From and To lists, and then
click Copy.
OMICRON 49
DGA Trending
DGA Trending is a licensed feature that visualizes a transformer’s historic Oil analysis data in various
charts and offers a comparison of data recorded at different points in time.
► Refer to 13.1.1 "Oil analysis" on page 105 for more detailed information on the Oil analysis test.
5.4.4 Spare bushing view

In the spare bushing view, you can specify bushings.
To specify a spare bushing:
1. From the Asset list, select Bushing.
2. From the Asset type list, select the type of the spare bushing.
Figure 5-14: Spare bushing view
3. In the spare bushing view, enter the general asset data (see Table 5-6: "General asset data" on
page 43).
4. Enter the spare bushing data (see 12.2 "Spare bushing" on page 91).
50 OMICRON
Jobs
5.4.5 Circuit breaker view

In the circuit breaker view, you can specify circuit breakers.
To specify a circuit breaker:
1. From the Asset list, select Circuit breaker.
2. From the Asset type list, select the type of the circuit breaker.
Figure 5-15: Circuit breaker view
3. In the circuit breaker view, enter further general asset data (see Table 5-6: "General asset data" on
page 43).
4. In the Circuit breaker area, enter the circuit breaker data (see 12.3 "Circuit breaker" on page 92).
5. Specify the operating mechanism of the circuit breaker (see "Operating mechanism tab" on page 52).
6. Optionally, specify the bushings mounted on the circuit breaker (see "Bushings tab (Circuit breaker)"
on page 53).
7. Set the assessment limits of the circuit breaker (see "Assessment limits tab" on page 54).
OMICRON 51
Operating mechanism tab

On the Operating mechanism tab, you can specify the circuit breaker’s operating mechanism.
Figure 5-16: Circuit breaker view: Operating mechanism tab
To specify an operating mechanism, enter the operating mechanism data (see 12.3.1 "Operating
mechanism" on page 93).
52 OMICRON
Jobs
Bushings tab (Circuit breaker)

On the Bushings tab, you can specify bushings mounted on the circuit breaker.
Figure 5-17: Circuit breaker view: Bushings tab
To specify a bushing:
1. From the Asset type list, select the type of the bushing for all circuit breaker’s terminals.
2. Enter the bushing data (see 12.2 "Spare bushing" on page 91).
Under Copy bushing data, you can copy data of a bushing to other bushings. To copy the bushing data,
select the respective bushings from the From and To lists, and then click Copy.
OMICRON 53
Assessment limits tab

On the Assessment limits tab, you can set the circuit breaker’s absolute and relative assessment limits.
Figure 5-18: Circuit breaker view: Assessment limits tab
To set the circuit breaker’s assessment limits:

1. On the Assessment limits tab, click Absolute limits or Relative limits.
2. Enter the assessment limits (see 12.3.3 "Assessment limits" on page 94).
54 OMICRON
Jobs
5.4.6 Current transformer view

In the current transformer view, you can specify current transformers.
To specify a current transformer:
1. From the Asset list, select Current transformer.
Figure 5-19: Current transformer view
2. In the current transformer view, enter the general asset data (see Table 5-6: "General asset data"
on page 43).
3. Enter the current transformer data (see 12.4 "Current transformer" on page 96).
OMICRON 55
5.4.7 Voltage transformer view

In the voltage transformer view, you can specify voltage transformers.
To specify a voltage transformer:
1. From the Asset list, select Voltage transformer.
2. From the Asset type list, select the type of the voltage transformer.
Figure 5-20: Voltage transformer view
3. In the voltage transformer view, enter the general asset data (see Table 5-6: "General asset data"
on page 43).
56 OMICRON
Jobs
5.4.8 Rotating machine view

In the rotating machine view, you can specify rotating machines.
To specify a rotating machine:
1. From the Asset list, select Rotating machine.
2. From the Asset type list, select the type of the rotating machine.
Figure 5-21: Rotating machine view
3. In the rotating machine view, enter the general asset data (see Table 5-6: "General asset data" on
page 43).
4. In the Configuration area and the Ratings area, enter the rotating machine data (see 12.6 "Rotating
machine" on page 102).
OMICRON 57
5.4.9 Miscellaneous view

In the miscellaneous view, you can specify miscellaneous assets.
To specify a miscellaneous asset:
1. From the Asset list, select Miscellaneous.
Figure 5-22: Miscellaneous view
2. In the miscellaneous view, enter the general asset data (see Table 5-6: "General asset data" on
page 43).
58 OMICRON
Jobs
5.5 Test view

In the test view, you can select, import and perform tests. To open the test view, click the Tests
navigation button .
Figure 5-23: Test view
5.5.1 Selecting tests

The test view is divided into the Available tests area, the Selected tests area, and the General test
settings area.
Click the button labeled with the test system with which you want to perform the test on the top of the
Available tests area. Then Primary Test Manager displays the available guided tests and optional
manual tests supported for the selected test system and the asset under test. To display the guided tests
grouped in categories, click the Show test categories button . .
You can select tests for different test systems supported by Primary Test Manager within the same job.
Then the symbol indicates the tests not available for the connected test system to signal to you that
you need to connect another test system before proceeding to execute the job.
OMICRON 59
For example, if the CPC 100 is connected to your computer and you configured a job with tests for the
CPC 100 and the CIBANO 500 as shown in the following figure, the symbol left next the
CIBANO 500 tests indicate that you must connect the CIBANO 500.
Figure 5-24: Job configured with test for the CPC 100 and the CIBANO 500 test systems
60 OMICRON
Jobs
If you, for example, try to perform a test for the CIBANO 500 with CPC 100 connected, a warning
message appears.
Figure 5-25: Warning message when trying to perform a test for the CIBANO 500
The optional manual tests are asset-independent. You can perform the tests for any asset described in
this User Manual, but Primary Test Manager does not guide you through the tests and provides no test
settings data. These tests offer a large amount of flexibility to define test procedures and specify test
settings according to your specific needs. For more information about the manual tests, see 8 "Create
new manual tests" on page 81.
The Selected tests area displays the tests you want to perform. By default, Primary Test Manager
displays the tests recommended by OMICRON. To add a test into the Selected tests area, click the
symbol next to the test name in the Available tests area. To add all tests of a category into the
Selected tests area, click the symbol. The Selected tests area displays the test to be performed in
the recommended order. You can change the order of the tests by dragging them or by using the and
symbols. To remove a test from the Selected tests area, click the symbol next to the test name.
The General test settings area displays the reason of the job, the global test conditions, and some asset
specific data.
OMICRON 61
5.5.2 Importing tests

In the test view, you can import tests performed with the CPC 100 and even with the test systems not
currently supported by Primary Test Manager. Primary Test Manager supports import of tests of the
following formats.
Table 5-7: Supported test formats
File Name Extension Description

.xml CPC files (jobs)
.xmt CPC template files (job templates)
.ptma Primary Test Manager manual test
.drax DIRANA native format
You can also import tests in JPG, PDF and any Microsoft Office file format.
To import test data:
1. In the Selected tests area, click Add from file.
2. In the Open dialog box, browse to the file you want the import.
3. In the left pane of the test view, click the imported test.
Figure 5-26: Test view after a test has been imported
4. In the workspace of the test view, you can change the test title and the test type.
62 OMICRON
Jobs
5. To open the test, click the Open button under Test data.
Note: To open a test, you must have installed the associated application software on your computer.
6. You can attach files as described earlier in this chapter and add comments to the test.
For information about importing and exporting jobs, see 7.6 "Import and export jobs" on page 80.
5.5.3 Performing tests

Note: To perform and assess the tests, you must know and understand the test settings and the
measurement data. For detailed information, see the respective chapters on the asset tests later in this
manual.
To perform a test:
1. Add the tests you want to perform into the selected tests area (see 5.5.1 "Selecting tests" on
page 59).
2. In the left pane of the test view, click the test you want to perform.
The test view is then split into the General pane, the Settings and conditions pane, the Measurements
pane and, if automatic assessment is available for the test, the Assessment pane. You can expand
and collapse the panes by clicking the arrows on the split bars.
3. In the Settings and conditions pane, enter the test settings (see the chapter on the asset tests later
in this manual).
Figure 5-27: Test view: Settings and conditions pane
OMICRON 63
4. In the Assessment pane, enter the automatic assessment parameters and limits, if applicable.
Figure 5-28: Test view: Assessment pane
64 OMICRON
Jobs
5. Connect the test setup to the asset under test according to the wiring diagram displayed in the
General pane. For information about connecting the test setup to the asset under test, see the
technical documentation shipped with the CPC 100, CP TD1, and CP SB1 test systems.
Figure 5-29: Test view: General pane
DANGER
Death or severe injury caused by high voltage or current
► Before connecting the test set to the test object, observe the five safety rules listed in
1 "Safety instructions" on page 8.
► Observe the relevant laws and internal safety standards.
OMICRON 65
6. In the Measurements pane, click Start to start the selected measurement.
Figure 5-30: Test view: Measurements pane
DANGER
The flashing lightning symbol in the Primary Test Manager test view indicates that an
output of the CPC 100 is active.
► Do not touch any of the CPC 100’s outputs or cables while the lightning symbol is
displayed.
► If in doubt, press the Emergency Stop button.
66 OMICRON
Jobs
7. Press the I/0 button on the front panel of the CPC 100.
Figure 5-31: Test view during a measurement
After the measurement has been finished, Primary Test Manager displays the numeric measurement
data and the automatic assessment, if available, in the Measurements pane. To view graphical diagrams
of the measurement results, click the Plot tab.
8. Repeat steps 6 and 7 for all test measurements.
Note: Some tests support starting all measurements at once by clicking the Start all button.
Note: After the test has been performed some asset data relevant for the test configuration cannot be
edited anymore.
OMICRON 67
5.5.4 Processing templates

In the guided test workflow, you can save jobs as templates and open the saved templates. With the help
of templates, you can configure jobs according to your needs (for example, for repeated routines), and
then repeatedly perform tests you only have to define once.
When you create a new job, the favorite template for the corresponding asset type and number of phases
is loaded automatically, if available.
To save a job as template:
1. In the guided test workflow, configure a job.
2. In the Selected tests area of the test view, click Save as template.
Figure 5-32: Save Tests as New Template dialog box
3. In the Save Tests as New Template dialog box:

► Select the Asset type and number of Phases.
► Enter a Name for the template.
4. Optionally, you can add a customized Microsoft Excel report template (see 11 "Generate test reports"
on page 86) to the job template. To add a Microsoft Excel report template:
► Click Select template.
► In the Select dialog box, browse to the report template you want to add.
68 OMICRON
Jobs
To open a template:
1. In the Selected tests area of the test view, click Open template.
Figure 5-33: Choose Template dialog box
2. In the Choose Template dialog box, select the asset type, the number of phases and the template
you want to open.
Note: If you added a Microsoft Excel report template to the job template, its location is displayed
under Customized Excel report template.
3. Press Replace existing testplan to replace the tests already listed in the test list.
Press Append to existing testplan to add the tests listed in the template to the end of the existing
testplan.
Note: If you click Append to existing testplan, the Microsoft Excel report template will not be added
the selected job template to the currently opened job.
OMICRON 69
5.6 Handling results

5.6.1 Trending tab
The Trending tab displays measurement data from PF/DF/Tanδ tests performed at rated frequency at
different points in time.
For the collection of data, the serial number and manufacturer are taken into account. Therefore, all
measurements of the bushing in question are displayed, regardless of its location (for example spare
bushing, bushing mounted on different transformers, etc.).
Trending is available for the following tests:
• Overall PF/DF/Tanδ & CAP test (see chapter 13.1.2 on page 110)
• Spare Bushing PF/DF/Tanδ & CAP – C1 test (see chapter 14.2 on page 154)
• Spare Bushing PF/DF/Tanδ & CAP – C2 test (see chapter 14.3 on page 157)
• Bushing PF/DF/Tanδ & CAP – C1 test (see chapter 13.1.3 on page 115)
• Bushing PF/DF/Tanδ & CAP – C2 test (see chapter 13.1.4 on page 120)
In the chart, measurements performed with 10 kV at rated frequency are displayed as circles . All other
data are displayed as triangles .
Note: If several tests are performed on one day, the most recent test of that day is connected to the
curve in the Trending chart. The others are displayed in the same chart but are not connected.
5.6.2 Assessing measurement results

► Use the Assessment column in the Measurements area of a test to assess the measurement results
or to change the automatic assessment provided by Primary Test Manager.
Table 5-8: Assessment statuses in the Test view
Status Description
Fail The status was automatically set to Fail by Primary Test Manager.
Manual fail The status was manually set to Fail.
Investigate The status was automatically set to Investigate by Primary Test
Manager.
Manual investigate The status was manually set to Investigate.
Pass The status was automatically set to Pass by Primary Test Manager.
Manual pass The status was manually set to Pass.
Not assessed The measurement has not been assessed.
Not rated The status was automatically set to Not Rated by Primary Test
Manager.
70 OMICRON
Jobs
5.6.3 Comparing results

Some tests support comparison of the graphical diagrams of measurement results. The comparison data
is an integral part of the tests. You can compare tests for different assets but we recommend to perform
only comparisons of tests for the same assets or assets of the same design type. Primary Test Manager
offers you only tests of the same type for which the comparison is possible.
To compare a test with a test available in the database during measurement:
1. In the home view (see 4 "Home view" on page 17), click the Create new job button .
2. In the Create new job view, configure a job as described earlier in this chapter.
3. In the test view (see 5.5 "Test view" on page 59), select the test you want to perform.
4. In the Measurements pane, click the + Select comparison button, if available.
5. In the Select a test window, select the test you want to compare with the current test.
Figure 5-34: Select a test window
OMICRON 71
6. The Measurements pane displays the measurement results of the selected test.
Figure 5-35: Test comparison: Measurement results of the first test
7. Start the test (see 5.5.3 "Performing tests" on page 63).

8. Click the Plot tab.
72 OMICRON
Jobs
9. Primary Test Manager displays the measurement results of both tests in real time.
Figure 5-36: Test comparison: Measurement results of both tests
To remove the comparison diagram, click Remove comparison.

Alternatively, you can compare two tests available in the database:
1. In the Manage view (see 7 "Manage objects" on page 75), select the job including the first test for
comparison.
2. In the left pane of the job overview, click the first test for comparison.
3. In the Measurements pane, click the + Select comparison button, if available.
4. In the Select a test window, select the second test for comparison.
5. Primary Test Manager displays the measurement results of both tests.
OMICRON 73
6 Execute prepared job

In the execute prepared job view, you can execute prepared jobs. To open the execute prepared job
view, click the Execute prepared job button in the home view.
In a typical application scenario, Primary Test Manager tests primary assets in the field. To facilitate the
field tests, you or your colleague can configure a job in the office, save it in Primary Test Manager, and
execute it later in the field. With the Execute prepared job user task, you can execute prepared jobs
saved in a file and jobs available in Primary Test Manager.
To execute a prepared job saved in a file:
1. In the home view, click the Execute prepared job button .
Figure 6-1: Execute prepared job view
2. In the execute prepared job view, click Open job from file.
3. In the Open dialog box, browse to the .ptm file you want to import.
4. Import the job, and then go through the guided test workflow (see 5 "Jobs" on page 34).
To execute a prepared job available in Primary Test Manager:
1. In the home view, click the Execute prepared job button .
2. In the execute prepared job view, search for the job you want to execute (see 7.1 "Search for objects"
on page 76).
3. Open the job, and then go through the guided test workflow (see 5 "Jobs" on page 34).
74 OMICRON
Manage objects
7 Manage objects
In the manage view, you can manage locations, assets, jobs, and reports available in Primary Test
Manager. After you have opened a job, Primary Test Manager leads you through the guided test
workflow (see 5 "Jobs" on page 34). To open the manage view, click the Manage button in the home
view.
Note: In this chapter, the locations, assets, jobs, and reports are collectively called objects.
Figure 7-1: Manage view
Note: The mounted assets are displayed in italics. To hide them, expand the Search area under Asset,
and then select the Hide mounted assets check box.
The manage view displays the objects in a hierarchical structure as follows:
• If you select a location, the manage view displays the assets, jobs, and reports associated with the
selected location.
• If you select an asset, the manage view displays the jobs and reports associated with the selected
asset.
• If you select a job, the manage view displays the reports associated with the selected job.
You can sort the objects alphabetically or in the chronological order.
► Drag and drop the column headers to rearrange the columns.
OMICRON 75
In the manage view, you can:

• Search for objects (see 7.1 "Search for objects" on page 76)
• Perform operations on objects (7.2 "Perform operations on objects" on page 77)
• Relocate assets (see 7.5 "Relocate assets" on page 79)
• Import and export jobs (7.6 "Import and export jobs" on page 80)
7.1 Search for objects

In the manage view, you can search for the objects available in Primary Test Manager:
• By searching for keywords in all object data
• By searching for keywords in particular object data
To search for keywords in all object data, type the keyword you search for in the respective Search box.
To search for keywords in particular object data:
1. Expand the Search area by clicking the arrow next to Search.
2. Type the keyword(s) you search for in the respective object data box(es).
The following table describes the location search data.
Table 7-1: Location search data
Data Description
Name Name of the location
Address Address of the location
City City where the asset is located
State/Province State or province where the asset is located
Postal code Postal code of the location
Country Country where the asset is located
The following table describes the asset search data.
Table 7-2: Asset search data
Data Description
Asset Asset under test
Asset type Type of the asset
Serial no. Serial number of the asset
Manufacturer Manufacturer of the asset
Manufacturer type Type of the asset according to the manufacturer
Asset system code Code of the asset used by the maintenance planning systems
Apparatus ID Identifier of the asset
76 OMICRON
Manage objects
The following table describes the job search data.
Table 7-3: Job search data
Data Description
Name/WO Name of the job or work order
Tested by Person who performed the test
Executed between Time period between the job was executed
Status Status of the job
The following table describes the report search data.
Table 7-4: Report search data
Data Description
Name Name of the report
Client Customer for which the report is designated
Created between Time period between the report was created
7.2 Perform operations on objects

To perform operations on objects, select an object from the respective list, and then do one of the
following:
► Click the Create new object button to add a new object of the same category.
► Click the Open selected object button to display the data of the selected object.
► Click the Delete selected object button to delete the selected object.
Additionally, you can copy jobs with the associated location, asset and test data. The test results and
reports are not copied. To copy a job:
1. Select the job you want to copy.
2. Click the Copy selected job button .
To perform operations on multiple objects, click Enable multiple selection in the menu bar, and then
do one of the following:
► To delete multiple locations, assets, jobs, and test reports, select the check boxes next to the objects
you want to delete, and then click the Delete selected object(s) button .
► To export multiple jobs, select the check boxes next to the jobs you want to export, and then click the
Export button .
7.3 Master locations and assets

Primary Test Manager supports master locations and assets to help you keep your data consistent.
When you create a job, the location and asset associated with that job – called master location and
master asset, respectively – are copied to the job.
Consequently, whenever you try to change the location or the asset of an existing job, a notification bar
at the top of the Primary Test Manager workspace prompts you to do one of the following:
OMICRON 77
► Click Import from master location or Import from master asset to import the location or asset
originally associated with the job (master location/asset) to the current job.
► Click Update master location or Update master asset to update the location or asset originally
associated with the job (master location/asset) with the data of the current job.
7.4 Duplicate assets

In the manage view, you can duplicate assets available in Primary Test Manager. To duplicate an asset:
1. From the asset list, select the asset you want to duplicate.
2. Click the Duplicate button .
3. In the asset view, type the serial number(s) of the new asset.
Figure 7-2: Asset view
4. In the asset view, click Save asset.

Note: By default, the duplicated asset are linked to location of the original asset. For relocating the asset
to a different location, see 7.5 "Relocate assets" later in this chapter.
78 OMICRON
Manage objects
7.5 Relocate assets

In the manage view, you can relocate assets available in Primary Test Manager. To relocate an asset:
1. From the asset list, select the asset you want to relocate.
2. Click the Relocate button .
Figure 7-3: Relocate Asset dialog box
3. In the Relocate Asset dialog box, select the location you want to move the asset to.
4. If the asset you want to relocate is mountable, select an asset where the moved asset is to be
mounted.
Note: You can filter the locations and assets by searching for keywords (see 7.1 "Search for objects" on
page 76).
OMICRON 79
7.6 Import and export jobs

Primary Test Manager supports data exchange between different test systems.
You can export jobs in the Primary Test Manager native PTM format. To export a job:
1. From the job list, select the job you want to export.
2. Click the Export button .
3. In the Save As dialog box, browse to the folder where you want to save the file.
You can import Primary Test Manager jobs in PTM format, test data in CSV format, and XML and SFRA
Doble files.
Note: During the import, the Doble XML data is mapped to the Primary Test Manager jobs.
To import a job:
1. Under Jobs, click the Import button .
2. In the Open dialog box, select the data format of the file you want to import.
3. Browse to the file you want to import.
80 OMICRON
Create new manual tests
8 Create new manual tests

Primary Test Manager assists you to create new manual tests. To open the create new manual tests
view, click the Create new manual tests button in the home view.
Figure 8-1: Create new manual tests view
The workspace of the create new manual tests view depends on the selected button in the left pane (see
Figure 8-2: "Left-pane buttons" on page 82). Initially, the workspace is divided into the General and
Tests areas.
In the General area, you can manage the connection to the test system as described in4.2.1 "Connecting
to a test system" on page 28.
The Tests area displays all manual tests supported by Primary Test Manager. Only the tests that are
available for the connected test system are active and can be added to a job as described in
chapter 8.1 "Add tests to a job" on page 82. You can open a test at any time by clicking the test in the
left pane. After you opened a test, the workspace is split into the Hardware configuration area, the
Settings and conditions area and the Measurements area.
OMICRON 81
If you click the Tests button, the workspace displays the General area and the Tests area again.
Figure 8-2: Left-pane buttons
Note: You can change the default test names. To rename a test, click the corresponding button in the
left pane, and then click the test name.
8.1 Add tests to a job

To add a test to a job, click the test in the Tests area. The selected test opens in the workspace and a
button with the test name appears in the left pane.
Note: You can open a selected test at any time by clicking the corresponding button in the left pane.
If a test is open, the workspace is divided into the following areas:
• Hardware configuration
Displays the test-specific controls of the test set.
• Settings and conditions
Displays the test settings.
• Measurements
Displays the measurement data graphically or numerically in table form.
For the description of the test settings and measurement data, see 20 "Optional manual tests" on
page 194).
8.2 Processing tests

By using the commands on the menu bar, you can process tests. The following table describes the
available operations.
Table 8-1: Menu bar commands
Command Action
Close Closes the current job and leads you to the Primary Test Manager home
view. Before closing the job, you can save the changes for all tests.
Save job Saves the current job. When saving for the first time, you must specify the
filename and directory of the job.
Save as Saves the current job in a newly specified directory.
Copy test Adds another test of the same kind and with the same settings to the test
list. Results are not copied.
Delete test Deletes the currently open test.
Note: Clicking Home in the title bar and Close in the menu bar have the same functionality.
82 OMICRON
Open manual tests
9 Open manual tests

With Primary Test Manager, you can open existing manual tests. To open manual tests:
1. Click the Open manual tests button in the home view (see Figure 4-1: "Primary Test Manager
home view" on page 17).
Figure 9-1: Open dialog box
OMICRON 83
2. In the Open dialog box, browse to the file you want to open.
Figure 9-2: Open manual tests view
The open manual tests view displays the tests in the left pane. To view the test results, click the
corresponding test button. You can add new tests and generate test reports as described in 8 "Create
new manual tests" on page 81.
84 OMICRON
Control tests
10 Control tests
In the Measurements area of Primary Test Manager, you can control the test execution. The following
table describes the available commands.
Table 10-1: Test control commands
Command Action
Start Starts the selected measurement of the currently open test.
Start all Starts all measurements of the currently open test.
Stop Stops the running measurement.
Stop all Stops all running measurements.
Clear all Deletes all measurement results of the currently open test.
Clear result Deletes the results of the selected measurement.
Delete measurement Deletes the selected measurement row.
Add measurement Adds a new measurement row to the currently open test.
OMICRON 85
11 Generate test reports

In the report view, you can configure and generate test reports. To open the report view, click the Report
button in the left pane.
Figure 11-1: Report view
The report view is divided into the New report area, the Settings area and the Existing reports area.
In the New report area, you can set the report data. The following table describes the report data.
Table 11-1: Report data
Data Description
Title Title of the report. Appears as the report header.
Report language Language the report is created in
Report ID1 Identifier of the report
Client Customer for which the report is designated
Logo Logo to appear in the report
(see "Setting the logo" later in this chapter)
Summary Text field to summarize the content of the test report in own words.
1. By default generated by Primary Test Manager.
86 OMICRON
Generate test reports
Setting the logo

To insert your own logo:
1. In the New report area, click Select image.
2. In the Open Image File dialog box, browse to the file you want to insert.
To set your own logo as default, click Set as default.
Configuring test reports

In the Settings area, you can configure test reports by selecting the respective check boxes. You can
generate test reports as Microsoft Word or in PDF format.
► To generate a test report in your preferred format, click Report to Word or Report as PDF.
You can use customized Microsoft Excel templates provided by OMICRON to tailor test reports to your
needs. For information about the test report templates, contact your OMICRON local sales
representative or distributor.
To open a test report template:
1. In the Settings area, click the Custom reports tab.
2. Click Select template.
3. In the Select dialog box, browse to the template you want to use.
► To set the customized test report template as default, click Set as default.
The Existing reports area displays the test reports available for the job. In addition to the test reports
generated by Primary Test Manager, you can add other reports to jobs. To add a report to a job:
1. In the Existing reports area, click Add report from file.
In the Add dialog box, browse to the report you want to add to the job.
OMICRON 87
12 Asset data
This section describes the asset specific data.
12.1 Transformer
The following tables describe the transformer data.
Table 12-1: Winding configuration
Data Description
Phases Number of the transformer’s phases
Vector group Vector group of the transformer
(see "Setting the vector group" on page 46)
Unsupported vector group Vector group not supported by Primary Test Manager as text for
(for documentation) documentation
Table 12-2: Ratings
Data Description
Rated frequency Rated frequency of the transformer
Voltage ratings
Winding Transformer’s winding
Voltage L-L L-L voltage of the transformer’s winding
Voltage L-N L-N voltage of the transformer’s winding
Insul. level L-L (BIL) L-L basic impulse level rating of the transformer’s winding
Power ratings
Rated power Power rating of the transformer
Cooling class Cooling class of the transformer
Temp. rise wind. Temperature rise of the transformer’s winding
Current ratings at rated power
H/X/Y1 Maximum power frequency current of the transformer at rated power
Short-circuit rating
Max. short-circuit current Maximum short-circuit current of the transformer in kA during a given time
in seconds
1. Set by the regional conventions (see 4.1.1 "Settings" on page 19).
88 OMICRON
Asset data
Table 12-3: Impedances
Data Description
Ref. temp. Reference temperature
Short-circuit impedances H - X1, H - Y1, X - Y1
Short-circuit impedance Short-circuit impedance of the transformer
Z (%)1
Base power Base power used for calculating the percent values of impedances
Base voltage Base voltage used for calculating the percent values of impedances
Load losses Pk Load loss at the transformer’s rated load
OLTC position Tap position of the OLTC
DETC position Tap position of the DETC
Zero sequence impedance
Base power Base power used for calculating the percent values of impedances
Base voltage Base voltage used for calculating the percent values of impedances
Zero sequence Zero sequence impedance of the transformer
impedance Z0 (%)
Table 12-4: Others
Data Description
Category Application category of the transformer
Status Usage status of the transformer
Tank type Type of the transformer’s tank
Insulation medium Insulation medium of the transformer
Weight Weight of the transformer’s insulation
Insulation
Volume Volume of the transformer’s insulation
Total weight Total weight of the transformer
Conductor material Conductor material of the transformer’s winding
12.1.1 Bushing
For the data of the transformer’s bushings, see 12.2 "Spare bushing" on page 91.
OMICRON 89
12.1.2 Tap changer

The following table describes the on-load tap changer (OLTC) and the de-energized tap changer (DETC)
data.
Table 12-5: Tap changer data
Data Description
OLTC/DETC Select the OLTC check box to set the OLTC data.
Select the DETC check box to set the DETC data.
Tap changer configuration
Winding Transformer’s winding to which the tap changer is connected
Tap scheme Notation scheme for tap identification
No. of taps Number of the tap changer’s taps
Current tap position1 Current position of the tap
Voltage table
Tap Number of the tap
Voltage Voltage on the tap
1. Only available for the DETC
12.1.3 Surge arrester

The following table describes the surge arrester data.
Table 12-6: Surge arrester data
Data Description
Ratings
Units in stack Number of the surge arrester’s units
Numerical positions Select the Numerical positions check box to set numerical positions of the
surge arrester.
Literal positions Select the Literal positions check box to set alphabetical positions of the surge
arrester.
Position Position of the surge arrester
Serial no. Serial number of the surge arrester
Voltage L-L Values needed to calculate the maximum test voltages
Voltage L-N
MCOV rating Maximum continuous operating voltage between the terminals of the surge
arrester
Unit catalog no. Identifier of the surge arrester unit
90 OMICRON
Asset data
12.2 Spare bushing

The following table describes the spare bushing data.
Table 12-7: Spare bushing data
Data Description
Pos.1 Terminal of the transformer’s winding to which the spare bushing is
connected
Ratings
Rated frequency Rated frequency of the spare bushing
Insul. level LL (BIL) L-L basic impulse level rating of the spare bushing
Voltage L-ground Rated line-to-ground voltage
Max. system voltage Maximum voltage between phases during normal service
Rated current Rating current of the spare bushing
Manufacturer info
Catalog no. Catalog number of the spare bushing
Drawing no. Drawing number of the spare bushing
Style no. Style number of the spare bushing
Nominal values
PF (C1)/ Power factor, dissipation factor, or tangent delta of the capacitance C1
DF (C1)/ between the top of the spare bushing and the voltage/test tap
Tanδ (C1)2
Cap. (C1) Capacitance C1 between the top of the spare bushing and the voltage/test
tap
PF (C2)/ Power factor, dissipation factor, or tangent delta of the capacitance C2
DF (C2)/ between the voltage/test tap of the spare bushing and ground
Tanδ (C2)2
Cap. (C2) Capacitance C2 between the voltage/test tap of the spare bushing and
ground
OMICRON 91
Table 12-7: Spare bushing data (continued)
Data Description
Other
Insulation type Insulation type of the spare bushing
Outer insulation type Outer insulation type of the spare bushing
1. Only available for spare bushings mounted on another assets
12.3 Circuit breaker

The following table describes the circuit breaker data.
Table 12-8: Circuit breaker data
Data Description
Circuit breaker
Number of phases Number of the circuit breaker’s phases
Number of interrupters Number of the circuit breaker’s interrupters per phase
per phase
Pole operation Pole operation of the circuit breaker
Pre-insertion resistors Select the Pre-insertion resistors (PIR) check box if the circuit breaker
(PIR) contains pre-insertion resistors.
PIR value Pre-insertion resistor value
Grading capacitors Select the Grading capacitors check box if the circuit breaker contains
grading capacitors.
Capacitor value Grading capacitor value
Interrupting medium Interrupting medium of the circuit breaker
Tank type Type of the circuit breaker’s tank
Ratings
Rated frequency Rated frequency of the circuit breaker
Rated voltage L-L Rated voltage of the circuit breaker
Rated current Rated current of the circuit breaker
Rated short-circuit Rated short-circuit breaking current of the circuit breaker
breaking current
Short-circuit nominal Nominal duration of the short-circuiting
duration
Rated insulation level Basic impulse level rating of the circuit breaker
(BIL)
Rated interrupting time Rated interrupting time of the circuit breaker
Interrupting duty cycle Interrupting duty cycle of the circuit breaker
Rated power at closing Rated power of the circuit breaker at closing
92 OMICRON
Asset data
Table 12-8: Circuit breaker data (continued)
Data Description
Rated power at opening Rated power of the circuit breaker at opening
Rated power at motor Rated power of the circuit breaker at motor charge
charge
Contact system
Total travel Total distance traveled by the contact during operation (excluding possible
overshoot)
Damping time Time in which the damping units are engaged to decelerate the circuit
breaker’s moving contacts
Nozzle length Length of the circuit breaker’s nozzle
Others
Total weight with oil/gas Total weight of the circuit breaker with oil or gas
Weight of oil/gas Weight of the circuit breaker’s oil or gas
Volume of oil/gas Volume of the circuit breaker’s oil or gas
Rated gas pressure Rated gas pressure of the circuit breaker at given temperature
12.3.1 Operating mechanism

The following table describes the data of the circuit breaker’s operating mechanism.
Table 12-9: Operating mechanism data
Data Description
Number of trip coils Number of trip coils to operate the circuit breaker
Number of close coils Number of close coils to operate the circuit breaker
Component Operating mechanism’s component
Rated voltage Rated voltage of the operating mechanism’s component
Rated current Rated current of the operating mechanism’s component
DC Select the DC check box to set the component’s DC operation
AC Select the AC check box to set the component’s AC operation
Frequency AC operation frequency
Rated operating pressure Rated operating pressure of the operating mechanism at given
temperature
12.3.2 Bushing
For the data of the circuit breaker’s bushings, see 16 "Spare bushing data" on page 98.
OMICRON 93
12.3.3 Assessment limits

The following table describes the circuit breaker’s absolute assessment limits.
Table 12-10: Absolute assessment limits
Setting Description
Contact resistance
R min Minimum limit of the contact resistance
R max Maximum limit of the contact resistance
Operating times1
t min Minimum limit of the operating time
t max Maximum limit of the operating time
Contact travel2
d min Minimum assessment limit
d max Maximum assessment limit
Add velocity zone Click Add velocity zone to define a velocity zone for assessment of the
contact travel velocity.
Coil currents
I min Minimum limit of the coil current
I max Maximum limit of the coil current
Pickup voltage
V min Minimum limit of the pickup voltage
V max Maximum limit of the pickup voltage
1. For the definitions of the operating times, see Table 17-7: "Operating times" on page 113.
2. Only available if testing with the CB TN3 modules
The following table describes the circuit breaker’s relative assessment limits.
Table 12-11: Relative assessment limits
Setting Description
Contact resistance
R ref Reference contact resistance
R dev Allowed deviation from the reference contact resistance
Operating times1
t ref Reference operating time
–t dev Allowed negative deviation from the reference operating time
+t dev Allowed positive deviation from the reference operating time
Contact travel2
d ref Reference velocity
94 OMICRON
Asset data
Table 12-11: Relative assessment limits (continued)
Setting Description
d dev Allowed deviation from the reference velocity
Add velocity zone Click Add velocity zone to define a velocity zone for assessment of the
contact travel velocity.
Coil currents
I ref Reference coil current
–I dev Allowed negative deviation from the reference coil current
+I dev Allowed positive deviation from the reference coil current
Pickup voltage
V ref Reference pickup voltage
V dev Allowed deviation from the reference pickup voltage
1. For the definitions of the operating times, see Table 17-7: "Operating times" on page 113.
2. Only available if testing with the CB TN3 modules
OMICRON 95
12.4 Current transformer

12.4.1 Common Parameters and settings
The table below lists all parameters and settings that are displayed for all standards, CT types and
classes.
In addition to these common parameters, specific additional parameters are displayed, depending on the
selected standard, CT type (protection or metering CT) and class. For these specific parameters, please
refer to the tables on pages 96 to 101.
Table 12-12: Ratings
Data Description
Standard Standard used for testing the current transformer
Rated frequency Rated frequency of the current transformer
Rated Ipn : Isn1 Rated primary- to-secondary current ratio of the current transformer
Rated Ipr : Isr 2
Primary windings Number of primary windings on the current transformer (for primary
reconnection)
IEEE C57.13
System voltage System voltage of the current transformer
Rated insulation level Basic impulse level rating of the current transformer
(BIL)
Rating factor (RF) Continuous thermal current rating factor of the current transformer
IEC 60044/IEC 61869
Um (r.m.s.) Highest voltage for equipment
U withstand (r.m.s.) Rated power-frequency withstand voltage
U lightning (peak) Rated lightning impulse withstand voltage
Icth Rated continuous thermal current
Idyn (peak) Rated dynamic current
Ith (r.m.s.) Rated short time thermal current
Duration Duration of rated short time thermal current
1. According to IEC 60444
2. According to IEC 61869 and IEEE C57.13
96 OMICRON
Asset data
Table 12-13: CT configuration
Data Description
Cores Number of the current transformer’s cores
Name Inter-tap identification
Ipn1/Ipr2 Inter-tap rated primary current
Isn1/Isr2 Inter-tap rated secondary current

In use Tap on which the CT is operated
Ratings
Application Application category of the current transformer
Class Rated accuracy class of the current transformer
Rated burden Rated burden of the current transformer
Burden Secondary burden of the current transformer
Operating burden Burden (VA value) connected to the current transformer
cos φ Phase angle of the secondary burden
12.4.2 IEC 60044 protection CTs

The following parameters are only displayed if the standard IEC 60044 is selected with the type
"Protection CT".
Table 12-14: Specific parameters and settings displayed for IEC 60044 protection CTs
Available for
IEC 60044 Available for
Param. Description protection CTs, IEC 60044, class
class
xP xPR PX TPS TPX TPY TPZ
ALF Accuracy limiting factor. x x
Win- Specified secondary winding resistance.
ding
x x x x x x
resi-
stance
Ts Specified secondary time constant. x x x
Kx Dimensioning factor. x
Ek Rated knee point e.m.f. x
Ie Accuracy limiting current x
E1 User-defined e.m.f. to verify the excitation current at this
x
specific e.m.f.
Ie1 Maximum allowed excitation current at E1. x
Kssc Rated symmetrical short-circuit current factor. x x x x
OMICRON 97
Available for
IEC 60044 Available for
Param. Description protection CTs, IEC 60044, class
class
xP xPR PX TPS TPX TPY TPZ
Tp Primary time constant. x x x x
K Dimensioning factor. x
V-al Rated equivalent excitation limiting secondary voltage. x
I-al Accuracy limiting secondary excitation current. x
Ktd Rated transient dimensioning factor. x x x
Duty Specified duty cycle. x x
t1 Duration of first current flow. The specified accuracy limit must
x x
not be reached within time tal1.
t-al1 Permissible time to accuracy limit for first energizing period of

x x
the duty cycle.
t2 Duration of second current flow. The specified accuracy limit
x x
must not be reached within time tal2.
t-al2 Permissible time to accuracy limit for second energizing period

x x
of the duty cycle.
tfr Dead time between first opening and reclosure. x x
"Metering CT".
Table 12-15: Specific parameters and settings displayed for IEC 60044 metering CTs
Available for
IEC 60044
metering CTs,
Param. Description class
0.1, 0.2, 0.2s, 0.5,
0.5s, 1, 3, 5
FS Instrument security factor. x
ext. Ipn Extended current rating. x
98 OMICRON
Asset data
12.4.3 IEC 61869 protection CTs

"Protection CT".
Available for IEC 61869
protection CTs, class
Param. Description transient
protection
protection
xP xPR PX PXR TPX TPY TPZ
ALF Accuracy limiting factor. x x
Win- Specified secondary winding resistance.
ding
x x x x x x
resi-
stance
Ts Specified secondary time constant. x x
Kx Dimensioning factor. x x
Ek Rated knee point e.m.f. x x
E1 User-defined e.m.f. to verify the excitation current at this
x x
specific e.m.f.
Ie Accuracy limiting current. x x
Ie1 Maximum allowed excitation current at E1. x x
Kssc Rated symmetrical short-circuit current factor. x x x
Duty The accuracy class assessment has to be performed for the
cycle specific protection requirements the CT is built for. According to
spec. the standard, these requirements are normally stated by the
duty cycle and the time constants.
However, in some cases the choice of one specific duty
x x x
cycle/time constant cannot describe all protection requirements.
Therefore, Primary Test Manager offers the possibility to
specify "more general requirements" (which cover the
requirements of different duty cycles and time constants) by
entering the Ktd instead.
Ktd Rated transient dimensioning factor according to the name

plate. x x x
Note: Only displayed if parameter "Duty cycle spec." is "by Ktd".
Tp Primary time constant.
Note: Only displayed if parameter "Duty cycle spec." is x x x
"by Duty".
Duty Specified duty cycle.
"by Duty".
OMICRON 99
Available for IEC 61869
protection CTs, class
Param. Description transient
protection
protection
xP xPR PX PXR TPX TPY TPZ
t-al1 Permissible time to accuracy limit for first energizing period of
the duty cycle.
x x x
Note: Only displayed if parameter "Duty cycle spec." is
"by Duty".
t1 Duration of first current flow. The specified accuracy limit must
not be reached within time tal1.
x x x
"by Duty" and "Duty" is "CO-CO".
tfr Dead time between first opening and reclosure.
t-al2 Permissible time to accuracy limit for second energizing period
of the duty cycle.
x x x
12.4.4 IEC 61869 metering CTs

"Metering CT".
Table 12-17: Specific parameters and settings displayed for IEC 61869 metering CTs
Available for
IEC 61869 metering
Param. Description CTs, class
0.1, 0.2, 0.2s, 0.5,
0.5s, 1, 3, 5
FS Instrument security factor. x
ext. Ipn Extended current rating. x
ext. VA Extended burden range. x
100 OMICRON
Asset data
12.4.5 IEEE C57.13 protection CTs

The following parameter is only displayed if the IEEE C57.13 standard is selected with the type
"Prot. CT".
Table 12-18: Specific parameters and settings displayed for IEEE C57.13 protection CTs
Available for
Param. Description IEEE C57.13, class
C T X K
Vb Rated secondary terminal voltage.
If the IEEE C57.13 standard is selected with the type "protection CT" (class C, K x x x
or T), the VA and Cos ϕ parameters are not accessible to the user. In this case,
the user has to enter the terminal voltage Vb instead.
Vk User-defined measuring point.
x x
Vk1 User-defined measuring point 1.
Ik User-defined measuring point.
x x
Ik1 User-defined measuring point 1.
RE(20*Isn) Ratio error at 20 * Isn. x
Winding Specified secondary winding resistance.
x
resistance
12.4.6 IEEE C57.13 metering CTs

The following parameter is only displayed if the IEEE C57.13 standard is selected with the type
"Metering CT".
Table 12-19: Specific parameters and settings displayed for IEEE C57.13 metering CTs
Available for
IEEE C57.13
metering CTs,
Param. Description class
0.15, 0.15s, 0.3, 0.6,
1.2
RF Continuous current rating factor. x
OMICRON 101
12.5 Voltage transformer

The table below lists all parameters and settings that are displayed for all standards, VT types and
classes.
Data Description
Standard Standard used for testing the voltage transformer
Rated frequency Rated frequency of the voltage transformer
Upr Rated primary voltage
Table 12-21: VT configuration
Data Description
Windings Number of windings on the voltage transformer
Usr Rated secondary voltage
Rated burden Rated burden of the voltage transformer
cos φ Phase angle of the secondary burden
12.6 Rotating machine

The following tables describe the rotating machine data.
Table 12-22: Configuration
Data Description
Star point1 Star point connection of the rotating machine during test
1. Only available for three-phase rotating machines
Data Description
Rated frequency Rated frequency of the rotating machine
Rated voltage L-L L-L voltage of the rotating machine
Rated current Rated current of the rotating machine
Rated speed (rpm) Rated speed of the rotating machine in revolutions per minute
Rated power Rated power of the rotating machine
102 OMICRON
Asset data
Table 12-23: Ratings (continued)
Data Description
Rated power factor Rated power factor of the rotating machine
Rated thermal class Rated thermal class of the rotating machine
Rated excitation current Rated excitation current of the rotor
(rotor)
Rated excitation voltage Rated excitation voltage of the rotor
(rotor)
12.7 Grounding system

The following tables describe the grounding system data. For reporting purposes, the location name is
automatically inserted into the Serial no. field.
Table 12-24: Grounding system
Data Description
Maximum grid current Parameters of the substation or test object
Maximum fault duration Maximum amount of time the fault is applied
Unlimited fault duration Activate the check box for an unlimited fault duration. Maximum fault
duration will be deactivated.
To document your measurement locations, you can add a Grounding system environment (for ground
impedance measurements) and Ground mat plan (for step and touch voltage measurements).
► To add an existing map as an image, press Select image .
► To create a snapshot from Bing Maps, press Show map .
Zoom into the desired area and press Create snapshot.
OMICRON 103
13 Transformer tests
In this chapter, the settings and measurement data of the transformer tests are described. Fore more
information about testing with the CPC 100, see the CPC 100 User Manual shipped with your test
system.
Note: Depending on your settings, some test names include the power factor (PF), the dissipation factor
(DF), or the tangent delta (Tanδ). The dissipation factor and the tangent delta are identical
characteristics of the primary asset under test. For your convenience, with Primary Test Manager you
can use your preferred naming. You can also select some test names to match your regional
conventions (see 4.1.1 "Settings" on page 19).
13.1 Two-winding transformers

Primary Test Manager supports the following tests of two-winding transformers:
• Oil analysis
• Overall1 PF/DF/Tanδ2 & CAP
• Bushing H/X2 PF/DF/Tanδ2 & CAP – C1
• Bushing H/X2 – Energized Collar
• Exciting current
• Insulating fluids PF/DF/Tanδ2 & CAP
• Surge arrester watt losses H/X2
• Leakage reactance1 H–X2
• Zero sequence impedance H/X2,3
• TTR1 H–X2
• DC winding resistance H/X2
• Dynamic OLTC-Scan H/X2
• Demagnetization
Primary Test Manager supports additionally the TanDelta – PF/DF/Tanδ & CAP manual test.
► For more information, see 20.2 "TanDelta – PF/DF/Tanδ & CAP test" on page 197.
1. Set by the preferences (see 4.1.1 "Settings" on page 19).

3. Only available for winding configurations with accessible neutral.
104 OMICRON
Transformer tests
13.1.1 Oil analysis

The Oil analysis test is used to add the results of oil analyses performed by an oil laboratory or using a
mobile DGA test instrument. The values can be entered directly or imported from an Excel file.
For the dissolved gas in oil values the standard assessments and visualization according to IEEE
C57.104-2008 and IEC 60599-2007-05 Edition 2.1. are performed.
The following table describes the Oil analysis test settings.
Table 13-1: Oil analysis – Settings and conditions
Setting Description
Asset
Asset Asset under test – set in the asset data
(see chapter 12 "Asset data" on page 88)
Tank type Type of transformer tank
Insulation medium Insulation medium of the transformer – set in the asset data
(see chapter 12 "Asset data" on page 88)
Note: The DGA is only valid for the insulation medium Mineral oil.
Oil type Type of transformer oil
Test conditions
Sample date Date of sample collection
Oil sample temperature Oil temperature at the time of sampling
Measurement
Analyzed by Information on how the sample was analyzed
• Oil lab: The sample was analyzed by a laboratory.
After selecting Oil lab, you can enter the Name and Address of the
laboratory.
• Mobile DGA: The sample was analyzed using a mobile DGA device.
After selecting Mobile DGA, you can enter the device
Manufacturer/Type and its Serial number.
• Online DGA: The sample was analyzed using a permanently
installed monitoring device.
After selecting Online DGA, you can enter the device
Manufacturer/Type and its Serial number.
Use C3 hydrocarbons Activate the Use C3 hydrocarbons check box to add C3H6 and C3H8
to the list of Gas in oil values, and to activate ratio assessment
according to the MSS scheme.
Sampling point Sampling point on the transformer tank:
• Top
• Middle
• Bottom
OMICRON 105
The following table describes the gas-in-oil values.
Table 13-2: Oil analysis – Gas-in-oil values
Data Description
TDCG Total dissolved combustible gas
TDG Total dissolved gas
TCGe Estimation of the percentage of total combustible gas in the gas space.
It will only correspond to the actually measured value if there is a
balance between the gas blanket and the oil.
Lab. result Assessment result of the laboratory according to the IEEE or IEC
standard.
Assessment Manual Gas-in-oil analysis assessment:
• Manual pass
• Manual fail
• Manual investigate
• Not assessed
Assessment Summary
The results are assessed using the following interpretation methods:
• Duval’s triangles (see Table 13-3 below)
• IEC basic gas ratios
• Roger’s ratios
• Doernenburg’s ratios
• Key gases according to IEEE C57.104 and IEC 60599 (see Table 13-3 below)
• MSS scheme
106 OMICRON
Transformer tests
Table 13-3: Examples of result visualization in the Assessment Summary section
Condition 4
Condition 3
Key gas ranges and conditions

according to IEEE C57.104
Condition 2
Condition 1
Indicator
Assumed fault –
see Assessment Summary
table
Duval’s triangle 1
Indicator
Indicator
Key gas ranges and conditions

according to IEC 60599,
visualized in 3D
OMICRON 107
Assessment Details
• The Table contains condition ranges and states for individual gases.
• The Ratio Table lists all used gas ratios, depending on the selected standard, and provides an
Interpretation of the recorded values.
Table 13-4: Oil analysis – Assessment Details
Data Description
Table
Standard Standard used for the condition assessment
Overall assessment Condition fulfilled by the measured value of an individual gas
TDCG ppm/day Increase in TDCG per day since the last measurement
Recommendation Recommended interval for future measurements
Ratio Table
Sample Date Date of the sampling
Duval Triangle
Duval’s triangles visualize faults in a triangular coordinate system (see Table 13-3).
• Triangle 1: gases formed by faults of low to high energy
• Triangle 4: gases formed more specifically by faults of low energy or temperature
• Triangle 5: gases formed more specifically by faults of high temperature
Pattern
The key gas results are visually compared to four reference patterns. If a reference graph matches the
measured value, it is highlighted.
Physico-chemical oil analysis

The following table describes the physico-chemical oil analysis data.
Table 13-5: Oil analysis – Physico-chemical oil analysis data
Data Description
Water content
H2O meas. Measured water content in oil
H2O @ 20 ºC Calculated water content in oil
Relative saturation Relative water saturation
Assessment Water content assessment
DC conductivity
Meas. value Measured DC conductivity
Test temperature Temperature of the oil during DC conductivity test
Field strength Field strength
Assessment DC conductivity assessment
108 OMICRON
Transformer tests
Table 13-5: Oil analysis – Physico-chemical oil analysis data (continued)
Data Description
Power factor
Standard Standard underlying the power factor analysis
Meas. value @ 25 ºC Power factor measured at 25 ºC
Meas. value @ 100 ºC Power factor measured at 100 ºC
Assessment Power factor assessment
Dielectric breakdown voltage
Standard Standard underlying the dielectric breakdown voltage analysis
Meas. value Measured dielectric breakdown voltage
Test temperature Oil temperature during dielectric breakdown voltage test
Assessment Dielectric breakdown voltage assessment
Chemical
Interfacial tension Interfacial tension of the oil
Neutralization value Neutralization value of the oil
Particle count Particle count of the oil
Color Color of the oil
Assessment Chemical assessment
The following table describes the test status.
Table 13-6: Test status
Status Description
Prepared
Partially executed See Table 5-1: "Job statuses" on page 34.
Executed
Note: The test status set in the Oil Analysis test is displayed in the job overview (see 5.2 "Job overview"
on page 36) under Tests.
OMICRON 109
13.1.2 Overall PF/DF/Tanδ & CAP test

The following table describes the Overall PF/DF/Tanδ & CAP test settings.
Table 13-7: Overall PF/DF/Tanδ & CAP test settings
Setting Description
Measurement settings
Test frequency Test frequency
Sweep settings
Frequency sweep Sweep profile:
None, OMICRON expertise (recommended), or CPC template
• None: no frequency sweep
• OMICRON expertise: sweep frequencies dynamically distributed
within the CPC 100 frequency range for optimum results
• CPC template: sweep frequencies specified by the CPC 100 test
templates
Voltage sweep (tip-up) Sweep profile:
None or OMICRON expertise
• None: no voltage sweep
• OMICRON expertise: sweep voltages dynamically distributed within
the asset-dependent voltage range for optimum results
Sweep profiles ► Click the pen button to create a frequency or voltage sweep
profile.
► Add up to 30 measurement points with individual output voltages or
frequencies. Double-click a value to change it.
► Mark a favorite to use it as the default sweep profile for future
tests.
Note: The predefined profiles None, OMICRON expertise and
CPC template cannot be edited or deleted.
The default sweep profiles for this test are:
• Frequency sweep: OMICRON expertise
• Voltage sweep: None
Noise suppression settings
Averaging (no. points) Number of averaged measurements
Bandwidth CP TD1 filter bandwidth
If this setting is active, the measurement will not be performed at the
Test frequency set in the Measurement section. Primary Test
Manager will instead measure two values at frequencies below and
above the entered Test frequency and calculate the median of those
Avoid test frequency
two values.
The Avoid test frequency setting is predefined for the selected test.
► Only change the default setting for special applications.
110 OMICRON
Transformer tests
Table 13-7: Overall PF/DF/Tanδ & CAP test settings (continued)
Setting Description
Device settings
Enable shield check Select the Enable shield check check box if you want that the
CPC 100 checks whether the shield of the high-voltage cable is
connected.
Use beeper Select the Use beeper check box if you want to use the CP TD1’s
beeper during the measurement.
Test conditions
Custom test conditions Activate the Custom test conditions check box to set test conditions
differing from the global test conditions.
Top oil temperature Oil temperature at the top of the transformer’s tank
Bottom oil temperature Oil temperature at the bottom of the transformer’s tank
Average oil temperature Calculated average oil temperature of the transformer’s tank
Winding temperature Temperature of the transformer’s winding
Ambient temperature Ambient temperature on site
Humidity Relative ambient humidity
Weather Weather during the test
Correction factors
Temperature correction Select the Temperature correction check box to activate temperature
correction.
Correction temp. In the Custom list, click the correction temperature, or type the
correction temperature beneath.
Correction factor Click the Calculate button to calculate the correction factor
automatically or type the correction factor beneath.
Use reference voltage Select the Use reference voltage check box to extrapolate the I out
and Watt losses results for the specified reference voltage.
Reference voltage Reference voltage for extrapolation of measurement results
Bushings compensation Select the Bushings compensation check box to activate bushings
compensation.
Note: Bushing compensation compensates the effect of the
capacitance C1 of the transformer’s bushings on the measurement
results of the test.
NOTICE
► Before making a decision based on the Primary Test Manager automatic assessment, read the
disclaimer 1.3.1 "Automatic assessment" on page 9.
Primary Test Manager supports automatic assessment for the following insulation media:
• Natural ester
OMICRON 111
• Mineral oil
• Silicone
if you activated the temperature correction by selecting the Temperature correction check box.
The following table describes the automatic assessment parameters of the Overall PF/DF/Tanδ & CAP
test.
Table 13-8: Overall PF/DF/Tanδ & CAP automatic assessment parameters
Parameter Description
Limit schema Limit schema underlying the assessment
Global assessment criteria
Min. Iout @10 kV Threshold value of the automatic assessment.
If Iout < Min. Iout @10 kV, the automatic assessment status is
Investigate.
To save the selected limit schema as the default setting for all future jobs, click Set as default.
Under Visible limits:
► Click only limits that are used for this measurement to display only limits for the selected
transformer’s insulation type.
► Click all limits to display limits for all supported transformer’s insulation types.
The following tables describe the automatic assessment limits of the Overall PF/DF/Tanδ & CAP test.
Table 13-9: Overall PF/DF/Tanδ & CAP automatic assessment limits based on Power Factor/Dissipation
Factor/Tanδ1
Assessment against Limit Power factor/

Dissipation factor/Tanδ1
Absolute limits for Low limit (fail)2 Limits for the measured
measurements power factor/
Low limit (warn.)2
dissipation factor/Tanδ
High limit (warn.)@<230 kV2,3
High limit (warn.)@>=230 kV2,3

High limit (fail)2
2. Set to the absolute limits.
3. According to the IEEE guidelines for oil isolated transformers the warning limit depends on the rated voltage (LL) of the primary
winding. If the rated voltage (LL) of the primary winding is less than 230 kV the first limit value is used for the high limit (warn.)
otherwise the second one is used. For an automatic assessment based on the IEEE guidelines for another insulation or based
on the IEC standards the same values for high limit (warn.)@<230 kV and high limit (warn.)@>=230 kV are set.
112 OMICRON
Transformer tests
If you selected the Use reference voltage check box Primary Test Manager performs additionally a
cross check by using the following additional limits.
Table 13-10: Overall PF/DF/Tanδ & CAP cross check limits based on Power Factor/Dissipation
Factor/Tanδ1

Dissipation factor/
Tanδ1
Absolute limits for cross check Multiplier (high warn. limit)2,3 Limits for the measured
power factor/
Multiplier (high fail limit)2,3/
dissipation factor/
Divider (low fail limit)2,3 Tanδ
2. The high warn., high fail and low fail limits are calculated from the cross check corrected values by using the respective
multiplier and divider and then compared to the corrected measured values.
3. The cross check assessment of the power factor/dissipation factor/Tanδ if the reference correction voltage is set to 10 kV.
Otherwise the cross assessment is based only on the capacitance.
Table 13-11: Overall PF/DF/Tanδ & CAP cross check limits based on capacitance
Assessment against Limit Capacitance

Relative limits for cross check Low limit (warn)/ Limits for the measured
High limit (warn) capacitance
Low limit (fail)/
High limit (fail)
You can assess the test:

• During measurement
To assess the test while the measurements are running, select the Assess during measurements
check box.
• Manually after all measurements have been finished
To assess the test manually, click Assess measurements.
After a measurement has been assessed, the test settings and the assessment parameters are locked.
If you change the nameplate data relevant for the assessment, for example, the insulation medium, after
a measurement has been assessed and you reopen the test, the following message appears.
To update the assessment, click Update and re-assess.

To change the test data, the test settings or the assessment parameters, click Clear all assessments.
You can overwrite the Primary Test Manager automatic assessment manually. To do so, click the arrow
next to the automatic assessment, and then select a manual assessment from the list.
Note: The automatic assessment is stored in the Assessment box for documentation purposes.
OMICRON 113
The following table describes the Overall PF/DF/Tanδ & CAP measurement data.
Table 13-12: Overall PF/DF/Tanδ & CAP measurement data
Data Description
No. Number of the measurement
Measurement Arrangement of the measurement
Test mode Test mode according to the IEEE Std 62-1995
Sweep Swept variable: frequency, voltage, or none
V test Test voltage
Freq. Test frequency
V out Measured output voltage
I out Measured output current
Watt losses Measured losses
PF meas/ Measured power factor, dissipation factor, or tangent delta
DF meas/
Tanδ meas1
PF corr/ Corrected measured power factor, dissipation factor, or tangent delta
DF corr/
Tanδ corr1
Cap. meas Measured capacitance
Assessment Measurement assessment
114 OMICRON
Transformer tests
13.1.3 Bushing H/X PF/DF/Tanδ & CAP – C1 test

The following table describes the Bushing H/X PF/DF/Tanδ & CAP – C1 test settings.
Table 13-13: Bushing H/X PF/DF/Tanδ & CAP – C1 test settings
Setting Description
Sweep settings
templates
• OMICRON expertise: sweep voltages dynamically distributed
within the asset-dependent voltage range for optimum results
profile.
tests.
• Voltage sweep: OMICRON expertise
two values.
OMICRON 115
Table 13-13: Bushing H/X PF/DF/Tanδ & CAP – C1 test settings (continued)
Setting Description
Device settings
connected.
Test conditions
Correction factors
correction.
Correction factor Temperature correction factor
Reference voltage Reference voltage for extrapolation of the measurement results
NOTICE
Primary Test Manager supports automatic assessment for the following bushing’s insulation types:
• Oil-impregnated paper
• Resin-bonded paper
• Resin-impregnated paper
For another type of the bushing’s insulation the automatic assessment cannot be done.
Note: The assessment can be done only if all bushings have the same insulation type.
116 OMICRON
Transformer tests
The following table describes the automatic assessment parameters of the Bushing H/X PF/DF/Tanδ &
CAP – C1 test.
Table 13-14: Bushing H/X PF/DF/Tanδ & CAP – C1 automatic assessment parameters
Investigate.
bushing’s insulation type and the PF (C1)/DF (C1)/Tanδ (C1)1 nameplate values (if entered) or the
absolute limits.
► Click all limits to display limits for all supported bushing insulation types and the
PF (C1)/DF (C1)/Tanδ (C1)1 nameplate values (if entered) or the absolute limits.
The following tables describe the automatic assessment limits of the Bushing H/X PF/DF/Tanδ & CAP –
C1 test.
Table 13-15: Bushing H/X PF/DF/Tanδ & CAP – C1 automatic assessment limits based on Power
Factor/Dissipation Factor/Tanδ1

Nameplate values Multiplier (high fail limit)2/ Limits based on the
PF (C1)/DF (C1)/
Divider (low warn. limit)2
Tanδ (C1) nominal values
Multiplier (high warn. limit)2
Absolute limits Low limit (fail)3 Limits based on the
PF (C1)/DF (C1)/
Low limit (warn.)3 Tanδ (C1) absolute limits
High limit (warn.)3
High limit (fail)3

2. The high fail, high warn. and low warn. limits are calculated from the nominal values by using the respective multiplier and
divider, and then compared to the corrected measured values. The low fail limit is set to 0.
OMICRON 117
Table 13-16: Bushing H/X PF/DF/Tanδ & CAP – C1 automatic assessment limits based on capacitance

Nameplate values Low limit (fail)1/ Limits based on the Cap. (C1)
nominal value
High limit (fail)1
Low limit (warn)1/

High limit (warn)1
The following table shows the Primary Test Manager assessment logic.
Table 13-17: Assessment logic
PF (C1)/DF (C1)/ Cap. (C1) Assessment

Tanδ (C1)1 nominal value
nominal value
Available Available Overall assessment
Available Not available Assessment based only on
PF (C1)/DF (C1)/
Tanδ (C1)1 nominal values
Not available Available Overall assessment
Not available Not available Assessment based only on
PF (C1)/DF (C1)/
Tanδ (C1)1 absolute limits

check box.
118 OMICRON
Transformer tests
If you change the following nameplate data relevant for the assessment:
• PF (C1)/DF (C1)/Tanδ (C1)1
• Cap. (C1)
• PF (C2)/DF (C2)/Tanδ (C2)1
• Cap. (C2)
• Bushing’s insulation type
After a measurement has been assessed and you reopen the test, the following message appears.

The following table describes the Bushing H/X PF/DF/Tanδ & CAP – C1 measurement data.
Table 13-18: Bushing H/X PF/DF/Tanδ & CAP – C1 measurement data
Data Description
Measurement Terminal name of the bushing under test
V test Test voltage
DF meas/
Tanδ meas1
DF corr/
Tanδ corr1
OMICRON 119
Table 13-18: Bushing H/X PF/DF/Tanδ & CAP – C1 measurement data (continued)
Data Description
PF ref/ Reference power factor, dissipation factor, or tangent delta
DF ref/
Tanδ ref1
Cap. ref Reference capacitance
13.1.4 Bushing H/X PF/DF/Tanδ & CAP – C2 test

The following table describes the Bushing H/X PF/DF/Tanδ & CAP – C2 test settings.
Table 13-19: Bushing H/X PF/DF/Tanδ & CAP – C2 test settings
Setting Description
two values.
Device settings
connected.
Test conditions
120 OMICRON
Transformer tests
Table 13-19: Bushing H/X PF/DF/Tanδ & CAP – C2 test settings (continued)
Setting Description
Correction factors
correction.
NOTICE
Primary Test Manager supports automatic assessment for the following bushing’s insulation types:
• Oil-impregnated paper
• Resin-bonded paper
• Resin-impregnated paper
For another type of the bushing’s insulation the automatic assessment cannot be done.
Note: The assessment can be done only if all bushings have the same insulation type.
The following table describes the automatic assessment parameters of the Bushing H/X PF/DF/Tanδ &
CAP – C2 test.
Table 13-20: Bushing H/X PF/DF/Tanδ & CAP – C2 automatic assessment parameters
Investigate.
bushing’s insulation type and the PF (C2)/DF (C2)/Tanδ (C2)1 nameplate values (if entered) or the
absolute limits.
► Click all limits to display limits for all supported bushing insulation types and the
PF (C2)/DF (C2)/Tanδ (C2)1 nameplate values (if entered) or the absolute limits.
OMICRON 121
The following tables describe the automatic assessment limits of the Bushing H/X PF/DF/Tanδ & CAP –
C2 test.
Table 13-21: Bushing H/X PF/DF/Tanδ & CAP – C2 automatic assessment limits based on Power
Factor/Dissipation Factor/Tanδ1

Nameplate values Multiplier (high fail limit)2/ Limits based on the
PF (C2)/DF (C2)/
Divider (low warn. limit)2
Tanδ (C2) nominal values
Multiplier (high warn. limit)2
Absolute limits Low limit (fail)3 Limits based on the
PF (C2)/DF (C2)/
Low limit (warn.)3 Tanδ (C2) absolute limits
High limit (warn.)3
High limit (fail)3

2. The high fail, high warn. and low warn. limits are calculated from the nominal values by using the respective multiplier and
divider, and then compared to the corrected measured values. The low fail limit is set to 0.
Table 13-22: Bushing H/X PF/DF/Tanδ & CAP – C2 automatic assessment limits based on capacitance

Nameplate values Low limit (fail)1/ Limits based on the Cap. (C2)
nominal value
High limit (fail)1
Low limit (warn)1/

High limit (warn)1
122 OMICRON
Transformer tests
The following table shows the Primary Test Manager assessment logic.
Table 13-23: Assessment logic
PF (C2)/DF (C2)/ Cap. (C2) Assessment

Tanδ (C2)1 nominal value
nominal value
Available Available Overall assessment
Available Not available Assessment based only on
PF (C2)/DF (C2)/
Tanδ (C2)1 nominal values
Not available Available Overall assessment
Not available Not available Assessment based only on
PF (C2)/DF (C2)/
Tanδ (C2)1 absolute limits

check box.
If you change the following nameplate data relevant for the assessment:
• PF (C1)/DF (C1)/Tanδ (C1)1
• Cap. (C1)
• PF (C2)/DF (C2)/Tanδ (C2)1
• Cap. (C2)
• Bushing’s insulation type
after a measurement has been assessed and you reopen the test, the following message appears.

OMICRON 123
The following table describes the Bushing H/X PF/DF/Tanδ & CAP – C2 measurement data.
Table 13-24: Bushing H/X PF/DF/Tanδ & CAP – C2 measurement data
Data Description
V test Test voltage
DF meas/
Tanδ meas1
PF corr/ Temperature corrected power factor, dissipation factor, or tangent delta
DF corr/
Tanδ corr1
DF ref/
Tanδ ref1
Cap. ref Reference capacitance
124 OMICRON
Transformer tests
13.1.5 Bushing H/X – energized collar test

The following table describes the Bushing H/X – Energized Collar test settings.
Table 13-25: Bushing H/X – Energized Collar test settings
Setting Description
two values.
Device settings
connected.
Test conditions
Correction factors
OMICRON 125
The following table describes the Bushing H/X – Energized Collar measurement data.
Table 13-26: Bushing H/X – Energized Collar measurement data
Data Description
V test Test voltage
13.1.6 Exciting current test

The following table describes the Exciting Current test settings.
Table 13-27: Exciting Current test settings
Setting Description
Tap changer settings
Type of tap changer Tap changer (OLTC/DETC) whose taps are changed during the test
Number of taps Number of taps of the tap changer
Start tap Start tap position of the test
Stop tap Stop tap position of the test
DETC position/ Tap position of the DETC or OLTC
OLTC position1
Test voltage Test voltage
Test phase Phase of the winding under test
Device settings
connected.
126 OMICRON
Transformer tests
Table 13-27: Exciting Current test settings (continued)
Setting Description
Correction factors
1. Only available if the transformer has both the OLTC and DETC tap changers and depends on the selected type of the tap
changer.
The following table describes the Exciting Current measurement data.
Table 13-28: Exciting Current measurement data
Data Description
Tap Tap changer position
I phase Measured primary current per phase
Reactance Measured reactance
Assessment Measurement assessment per tap position
13.1.7 Insulating fluids PF/DF/Tanδ & CAP test

The following table describes the Insulating Fluids PF/DF/Tanδ & CAP test settings.
Table 13-29: Insulating fluids PF/DF/Tanδ & CAP test settings
Setting Description
two values.
OMICRON 127
Table 13-29: Insulating fluids PF/DF/Tanδ & CAP test settings (continued)
Setting Description
Device settings
connected.
Test conditions
Oil temperature Temperature of the oil
Correction factors
correction.
The following table describes the Insulating Fluids PF/DF/Tanδ & CAP measurement data.
Table 13-30: Insulating fluids PF/DF/Tanδ & CAP measurement data
Data Description
Specimen Oil sample under test
V test Test voltage
128 OMICRON
Transformer tests
Table 13-30: Insulating fluids PF/DF/Tanδ & CAP measurement data (continued)
Data Description
DF meas/
Tanδ meas1
DF corr/
Tanδ corr1
OMICRON 129
13.1.8 Surge arrester watt losses H/X test

The following table describes the Surge Arrester Watt Losses H/X test settings.
Table 13-31: Surge Arrester Watt Losses H/X test settings
Setting Description
two values.
Device settings
connected.
Test Conditions
Correction factors
130 OMICRON
Transformer tests
The following table describes the Surge Arrester Watt Losses H/X measurement data.
Table 13-32: Surge Arrester Watt Losses H/X measurement data
Data Description
Measurement Terminal name of the surge arrester under test
Position Surge arrester unit under test
V test Test voltage
13.1.9 Leakage reactance H-X

Note: The name of this test depends on the standard you choose in Primary Test Manager.
• According to the IEEE standard: Leakage Reactance H-X
• According to IEC standard: Short-Circuit Impedance H-X
In this chapter, the term Leakage Reactance H-X will be used.
The following table describes the Leakage Reactance H–X test settings.
Table 13-33: Leakage Reactance H–X test settings
Setting Description
Test current Test current
OLTC position Tap position of the OLTC
DETC position Tap position of the DETC
3Ph equiv. test
Perform test Select the Perform test check box if you want to perform the
3Ph equiv. test.
Show FRSL results Select the Show FRSL results check box to show the FRSL results of
the 3Ph equiv. test.
Per-phase test
Perform test Select the Perform test check box if you want to perform the Per-
phase test.
Show FRSL results Select the Show FRSL results check box to show the FRSL results of
the Per-phase test.
OMICRON 131
Table 13-33: Leakage Reactance H–X test settings (continued)
Setting Description
Test conditions
correction.
Reference temp. Reference temperature to be used for temperature correction
Corr. factor Temperature correction factor
Primary Test Manager supports automatic assessment of the Leakage Reactance H–X test. The
relevant data are grouped in the Assessment pane.
The automatic assessment is only possible if you have completed the steps below:
► Enter the following transformer nameplate data:
– Leakage Reactance Z (%)
– Base power:
Primary Test Manager determines the base power used for assessment using the following
information in the specified order:
1.The base power entered in the table of the Leakage Reactance field of the transformer
nameplate
2.The base power entered in the Zero sequence impedance field of the transformer nameplate
– Base voltage
Primary Test Manager determines the base voltage used for assessment using the following
information in the specified order:
1.The base voltage entered in the Leakage Reactance table in the transformer nameplate
2.The voltage of the tap (if a tap changer is available)
3.The base power entered in the Zero sequence impedance field of the transformer nameplate
► Activate the temperature correction by selecting the Temperature correction check box.
NOTICE
The automatic assessment is based on the selected limit schema. You can use predefined limit schemes
according to the established standards or set customer specific limits. In the Limit schema box, select
the limit schema you want to use for the assessment. To assign the selected limit schema to the asset
under test, click Set as default. The automatic assessment limits differ depending on the number of the
transformer’s phases.
132 OMICRON
Transformer tests
Single-phase transformers
The following table describes the automatic assessment limits for the single-phase transformer.
Table 13-34: Leakage Reactance H–X automatic assessment limits for single-phase transformer
Assessment against Limit Default

Zk dev (%) relative to nameplate Low limit (fail) Default limit
During the test, Primary Test Manager calculates the Zk meas (%) value1. For the automatic
assessment, Primary Test Manager compares Zk meas (%) with the nameplate value Zk leakage
reactance (%). If the deviation is less than the default limit, the assessment is set to Pass, otherwise to
Fail.
Three-phase transformers
The following table describes the automatic assessment limits for the three-phase transformer.
Table 13-35: Leakage Reactance H–X automatic assessment limits for three-phase transformer

3Ph equiv. Zk (%) relative to nameplate Low limit (fail) Default limit
Per-phase equiv. Zk (%) relative to average of all Low limit (fail) Default limit
phases
During the 3Ph equiv. measurement, Primary Test Manager calculates one Zk meas (%) value for all
phases. For the automatic assessment, Primary Test Manager compares Zk meas (%) with the
nameplate value Zk ref (%). If the deviation is less than the default limit the assessment status is set to
Pass, otherwise to Fail.
During the Per-phase measurement, Primary Test Manager calculates the Zk meas (%) values for each
phase. For the automatic assessment, Primary Test Manager compares Zk meas (%) with the average
of Zk meas (%) across all phases. If the deviation is less than the default limit, the assessment status is
set to Pass, otherwise to Fail.
You can assess the test at two points in the process:
• Assessment during the measurement
To assess the test while the measurements are running, activate the
Assess during measurements check box. After this, the test is locked, and you can only change
assessment-relevant data, for example, the nominal values.
• Manual assessment after all measurements have been finished
To assess the test manually, click Assess measurements. After that, the test is locked, and you can
only change assessment-relevant data, for example, the nominal values.
To set new data in the test or to change the test settings, click Clear all assessments.
1. In the Transformer area of the Settings dialog box, you can change the Short-circuit impedance (Leakage reactance)
abbreviation (see "Profiles: Transformer" on page 22).
OMICRON 133
Measurements: 3Ph equiv.

The following table describes the leakage reactance results (Zk).
Table 13-36: Leakage Reactance results (Zk)
Data Description
Phase Phase under test
I AC Measured current
V1 AC Measured voltage
V1 AC phase Phase angle of the voltage V1 AC
Zk Measured leakage reactance
Rk Real part of the measured Zk
Xk Imaginary part of the measured Zk
(leakage reactance)
Lk Measured leakage inductance
The following table describes the assessment Zk.
Table 13-37: Assessment Zk
Data Description
Zk meas (%) Measured leakage reactance in percent
Zk avg (%) Average of Zk meas (%) across all phases
Zk dev (%) Deviation of the Zk meas (%) from the Zk ref (%) in percent
Xk meas (%) Measured reactance in percent
Xk avg (%) Average of Xk meas (%) across all phases
Xk dev (%) Deviation of the Xk meas (%) from the Xk ref (%) in percent
The following table describes the assessment Rk at 400 Hz.
Table 13-38: Assessment Rk at 400 Hz
Data Description
Rk avg Average value of the per phase Rk
Rk dev (%) phase A Deviation of the measured Rk of the phase A from the average value
Rk dev (%) phase B Deviation of the measured Rk of the phase B from the average value
Rk dev (%) phase C Deviation of the measured Rk of the phase C from the average value
134 OMICRON
Transformer tests
Measurements: per-phase
The following table describes the leakage reactance results (Zk).
Table 13-39: Leakage Reactance results (Zk)
Data Description
Zk Measured leakage reactance
Rk Real part of the measured Zk
Xk Imaginary part of the measured Zk
(leakage reactance)
Lk Measured leakage inductance
The following table describes the assessment Zk.
Table 13-40: Assessment Zk
Data Description
Zk meas (%) Measured impedance in percent
Zk ref (%) Reference impedance in percent
(Corresponds to the nameplate value Z %.)
Zk dev (%) Deviation of the measured impedance from the reference impedance in
percent
Xk meas (%) Measured reactance in percent
Xk ref (%) Reference reactance in percent
Xk dev (%) Deviation of the Xk meas (%) from the Xk ref (%) in percent
Dominance order Order of the Zk dev (%) values:
1 for the highest value
2 for the middle value
3 for the lowest value
OMICRON 135
The following table describes the assessment Rk at 400 Hz.
Table 13-41: Assessment Rk at 400 Hz
Data Description
Rk avg Average value of the per phase Rk
Rk dev (%) phase A Deviation of the measured Rk of the phase A from the average value
Rk dev (%) phase B Deviation of the measured Rk of the phase B from the average value
Rk dev (%) phase C Deviation of the measured Rk of the phase C from the average value
136 OMICRON
Transformer tests
13.1.10 Zero Sequence Impedance H/X test

The following table describes the Zero Sequence Impedance H/X test settings.
Table 13-42: Zero sequence impedance H/X Test Settings
Setting Description
Test current Current of the test
Test conditions
Winding temp. Temperature of the transformer’s winding
correction.
OLTC position1
Assessment settings
Manual Click Manual to select the manual assessment settings.
Automatic Click Automatic to select the automatic assessment settings
(see "Editing automatic assessment settings" later in this section).
changer.
NOTICE
OMICRON 137
Editing automatic assessment settings

To edit the automatic assessment settings:
1. In the Settings and conditions pane, click Edit test limits.
Figure 13-1: Edit automatic assessment limits dialog box
2. In the Edit automatic assessment limits dialog box, enter the deviation of the Z0 (%) from the
Z0 ref (%) in percent.
The following table describes the Zero Sequence Impedance H/X measurement data.
Table 13-43: Zero Sequence Impedance H/X Measurement Data
Data Description
Z meas Measured impedance
Z corr Temperature corrected impedance
Z0 Measured zero sequence impedance
Z0 (%) Measured zero sequence impedance in percent
Z0 ref (%) Reference zero sequence impedance in percent
Z0 dev (%) Deviation of the Z0 (%) from the Z0 ref (%) in percent
138 OMICRON
Transformer tests
13.1.11 TTR H–X test

You can perform the TTR H–X test also for the vector groups not supported by Primary Test Manager
according to the IEC 61378-1 standard. To perform the test according to the IEC 61378-1 standard,
select the IEC 61378-1 check box in the Settings and conditions pane.
The following table describes the TTR H–X test settings.
Table 13-44: TTR H–X test settings
Setting Description
OLTC position1
CP SB1 settings
Use CP SB1 Select the CP SB1 check box to perform the test by using the CP SB1
switch box.
Auto switching of phases Phases are switched automatically;
Switching through taps is done manually.
Auto switching of taps and Switching through taps and phases is both done automatically.
phases
Tap time Time for the automatic tap change between two positions
Impulse time Duration of the impulse for the automatic tap change
IEC 61378-12 Select the IEC 61378-1 check box to perform the test according to the
IEC 61378-1 standard.
Ratio Choose between TTR (transformer turns ratio) and VTR (voltage ratio)
to be displayed in the Measurements table.
Assessment settings
changer.
2. The CP SB1 and Automatic tap control check boxes must be selected.
OMICRON 139
NOTICE

2. In the Edit automatic assessment limits dialog box, enter the deviation of the measured
transformer ratio from the nominal transformer ratio in percent.
The following table describes the TTR H–X measurement data.
Table 13-45: TTR H–X measurement data
Data Description
Nominal ratio Nominal transformer ratio
V prim Measured primary voltage
I prim1 Measured primary current
I phase1 Phase angle of the measured primary current

V sec Measured secondary voltage
V phase Phase shift between primary and secondary voltage
TTR Measured transformer turns ratio
VTR Measured voltage ratio
Ratio dev Deviation of the measured transformer ratio from the nominal
transformer ratio
1. Not available if the test is performed according to the IEC 61378-1 standard.
140 OMICRON
Transformer tests
13.1.12 DC Winding Resistance H/X test

The following table describes the DC Winding Resistance H/X test settings.
Table 13-46: DC Winding Resistance H/X test settings
Setting Description
DETC Position/ Tap position of the DETC or OLTC
OLTC Position1
CP SB1 settings
Use CP SB1 Select the CP SB1 check box to perform the test by using the CP SB1
switch box.
Mode Switching mode for taps and phases
Manual Switching through taps and phases is both done manually.
Auto switching of taps Taps are switched automatically;
Switching through phases is done manually.
Auto switching of taps and Switching through taps and phases is both done automatically.
phases
Tap time Time for the automatic tap change between two positions.
Impulse time Duration of the impulse for the automatic tap change.
Up/Down test Select the Up/Down test check box to run the test in two directions (up
and down). Up means from the lowest tap to the highest tap while down
means from the highest tap to the lowest tap.
CPC output DC current output of the CPC 100
Automatic result Select the Automatic result check box to stop the measurement
automatically depending on the tolerance R dev and the settling time.
Tolerance R dev Tolerance of the deviation of consecutive measurement results within
the settling time
Settling time (∆t) Time within which the deviation of consecutive measurement results is
evaluated. If the deviation is less than the tolerance R dev, the
measurement stops.
OMICRON 141
Table 13-46: DC Winding Resistance H/X test settings (continued)
Setting Description
Show TRTapCheck results Select the Show TRTapCheck results check box to display information
about the condition (ripple and slope) of the tap changer mechanisms
Test conditions
correction.
changer.
NOTICE
Primary Test Manager supports automatic assessment of the DC Winding Resistance H/X test.
The following table describes the automatic assessment parameters of the DC Winding Resistance H/X
test.
Table 13-47: DC Winding Resistance H/X automatic assessment parameters
The following table describes the automatic assessment limits of the DC Winding Resistance H/X test.
Table 13-48: DC Winding Resistance H/X automatic assessment limits

Relative limits Limit (fail) Default limit
During the automatic assessment, Primary Test Manager compares the R corr values of all phases to
each another. If a deviation is greater than the default limit the assessment status is set to Fail.
check box.
142 OMICRON
Transformer tests
The following table describes the DC Winding Resistance H/X measurement data.
Table 13-49: DC Winding Resistance H/X measurement data
Data Description
I DC Measured current
V DC Measured voltage
Time Time between the start and stop of a measurement
R meas Measured resistance
R dev Deviation of two successive measurement results at the time the test was
stopped
R corr Corrected measured resistance
Ripple1 Highest current ripple during the tap changer operation
Slope1 Highest measured falling edge slope of the test current during the tap
changer operation
1. Only available if an OLTC is specified and the Show TRTapCheck results check box is selected
Note: If you did not select the Automatic result check box to stop the measurement automatically, you
can stop the measurement by clicking the Keep results button.
OMICRON 143
13.1.13 Dynamic OLTC-Scan (DRM)

Use the Dynamic OLTC-Scan test card to visualize the on-load tap changer’s transient switching
behavior and assess its condition.
A Dynamic OLTC-Scan can only be performed on resistive OLTCs and with the following settings
adjusted:
► Define the transformer’s winding configuration in the Transformer tab of the Asset view
(see "Setting the vector group" on page 46).
► Enter the No. of taps in the Tap changers tab of the Asset view. The No. of taps must be greater
than 1 (see 12.1.2 "Tap changer" on page 90).
Settings and conditions pane

The following table describes the Dynamic OLTC-Scan settings and conditions:
Table 13-50: Dynamic OLTC-Scan test settings
Setting Description
CP SB1 settings
Mode Switching mode for taps
Manual switching of taps Taps are switched manually.
Auto switching of taps Taps are switched automatically.
Tap time Time for the automatic tap change between two positions
Impulse time Duration of the impulse for the automatic tap change
Recording time The time of the switching cycle that shall be recorded
the settling time
measurement stops.
Noise suppression Select the Noise suppression check box to activate an interference
filter.
Dynamic shorting Dynamic short-circuit of low-voltage windings on single- and three-
phase transformers.
Only selectable for two- and three-winding transformers with an OLTC
on the high-voltage winding.
144 OMICRON
Transformer tests
Measurements pane
The Measurements pane in the workspace displays the measurement results in table and graph format.
► Highlight a line to indicate the corresponding graph and vice versa.
► Use the Assessment drop-down box to manually assess the test results.
► To view graphical diagrams of the measurement results, click the Plot tab.
Filters
The following table describes the filters available for the Dynamic OLTC-Scan:
Table 13-51: Available filters for the Dynamic OLTC-Scan
Filter Description
Phase Only results from the currently selected phase are displayed.
Parity Only results from taps with even/odd numbers are displayed.
Direction Only results from one direction of the OLTC’s movement are displayed.
Note: The Dynamic OLTC-Scan is restricted to 50 taps at once. For OLTCs with more than 50 taps,
enter the appropriate Start tap and Stop tap to define which set of 50 taps you would like to examine.
Errors during the test

In case of an error during measurement, the phrase "Some measurement results could not be recorded"
is displayed. Faulty measurement results are not displayed and instead marked with exclamation points:
Table 13-52: Error messages during the Dynamic OLTC-Scan
Notification Description
! Data corruption: A disturbance has been detected. This result is invalid.
Repeat the measurement.
!! Time out: No switching operation has been detected during the Tap time.
OMICRON 145
13.1.14 Demagnetization test

With the Demagnetization test, you can demagnetize the transformer’s core. We recommend to perform
the Demagnetization test after every DC Winding Resistance H/X test.
Note: For the demagnetization test, you must connect the CP SB1 transformer switch box to the
CPC 100.
The following table describes the Demagnetization test settings.
Table 13-53: Demagnetization test settings
Setting Description
Saturation criteria
Saturation level Saturation level of the transformer
The following table describes the Demagnetization measurement data.
Table 13-54: Demagnetization measurement data
Data Description
Measurement Name of the measurement
Stage Test status:
• Wiring check
• Saturating
• Discharging
• Canceled
• Demagnetizing
• Test stopped
• Core is demagnetized1
Min. neg. remanence Maximum remanence in negative direction of the hysteresis curve
Max. pos. remanence Maximum remanence in positive direction of the hysteresis curve
Remanence Measured remanence
Initial remanence Measured remanence at start of the test
1. If the measured remanence < 1%.
146 OMICRON
Transformer tests
13.2 Three-winding transformers

Primary Test Manager supports the following tests of three-winding transformers:
• Oil analysis
• Bushing H/X/Y2 PF/DF/Tanδ2 & CAP – C1
• Bushing H/X/Y2 – Energized Collar
• Exciting Current
• Insulating Fluids PF/DF/Tanδ2 & CAP
• Surge Arrester Watt Losses H/X/Y2
• Leakage Reactance1 H–X2
• Leakage Reactance1 H–Y2
• Leakage Reactance1 X–Y2
• Zero Sequence Impedance H/X/Y2,3
• TTR1 H–X2
• TTR1 H–Y2
• DC Winding Resistance H/X/Y2
• Dynamic OLTC-Scan H/X/Y2
• Demagnetization
Note: The tests of the three-winding transformers are identical or analogous to the respective tests of
the two-winding transformers. For more information, see 13.1 "Two-winding transformers" on page 104.
Primary Test Manager supports additionally the TanDelta – PF/DF/Tanδ & CAP manual test. For more
information, see 20.2 "TanDelta – PF/DF/Tanδ & CAP test" on page 197.

3. Depends on the availability of the transformer’s neutral.
OMICRON 147
13.3 Autotransformers without tertiary winding

Primary Test Manager supports the following tests of autotransformers without tertiary winding:
• Oil analysis
• Surge Arrester Watt Losses H/X2
• Zero Sequence Impedance H/X2
• TTR1 H–X2
• DC Winding Resistance H/X2
• Demagnetization
Note: The tests of the autotransformers without tertiary winding are identical to the respective tests of
the two-winding transformers. For more information, see 13.1 "Two-winding transformers" on page 104.

148 OMICRON
Transformer tests
13.4 Autotransformers with tertiary winding

Primary Test Manager supports the following tests of autotransformers with tertiary winding:
• Oil analysis
• Bushing H/X/Y2 – Energized Collar
• Surge Arrester Watt Losses H/X/Y2
• Leakage Reactance1 H–Y2
• Leakage Reactance1 X–Y2
• Zero Sequence Impedance H/X/Y2,3
• TTR1 H–X2
• TTR1 H–Y2
• DC Winding Resistance H/X/Y2
• Dynamic OLTC-Scan H/X/Y2
• Demagnetization
Note: The tests of the autotransformers with tertiary winding are identical to the respective tests of the
two-winding transformers. For more information, see 13.1 "Two-winding transformers" on page 104. The
available tests depend on the accessibility of the tertiary winding.

3. Depends on the availability of the transformer’s neutral.
OMICRON 149
13.5 Voltage regulators

Primary Test Manager supports the following tests of voltage regulators:
• Oil analysis
• Zero Sequence Impedance H/X2
• TTR1 H–X2
• DC Winding Resistance H/X2
• Demagnetization
Note: The tests of the voltage regulators are identical to the respective tests of the two-winding
transformers. For more information, see 13.1 "Two-winding transformers" on page 104.

150 OMICRON
Spare Bushing tests
14 Spare Bushing tests

In this chapter, the settings and measurement data of the spare bushing tests are described. Fore more
system.
Primary Test Manager supports the following spare bushing tests:
• Spare Bushing PF/DF/Tanδ1 & CAP – Overall
• Spare Bushing PF/DF/Tanδ1 & CAP – C1
• Spare Bushing PF/DF/Tanδ1 & CAP – C2
• Spare Bushing PF/DF/Tanδ1 & CAP – C1+C2
• Spare Bushing PF/DF/Tanδ1 & CAP – Energized Collar
OMICRON 151
14.1 Spare Bushing PF/DF/Tanδ & CAP – Overall

The following table describes the Spare Bushing PF/DF/Tanδ & CAP – Overall test settings.
Table 14-1: Spare Bushing PF/DF/Tanδ & CAP – overall test settings
Setting Description
Sweep settings
templates
profile.
tests.
• Voltage sweep: none
Bandwidth CPC 100 filter bandwidth
Device settings
connected.
152 OMICRON
Spare Bushing tests
Table 14-1: Spare Bushing PF/DF/Tanδ & CAP – overall test settings (continued)
Setting Description
Test conditions
Correction factors
correction.
The following table describes the Spare Bushing PF/DF/Tanδ & CAP – Overall measurement data.
Table 14-2: Spare Bushing PF/DF/Tanδ & CAP – overall measurement data
Data Description
V test Test voltage
DF meas/
Tanδ meas1
DF corr/
Tanδ corr1
OMICRON 153
14.2 Spare Bushing PF/DF/Tanδ & CAP – C1 test

The following table describes the Spare Bushing PF/DF/Tanδ & CAP – C1 test settings.
Table 14-3: Spare Bushing PF/DF/Tanδ & CAP – C1 test settings
Setting Description
Perform inverted C1 test Select the Perform inverted C1 test check box to include the inverted
C1 measurement in the test.
Sweep settings
Frequency sweep Sweep frequency profile:
None, OMICRON expertise (recommended), or CPC template.
templates
profile.
tests.
• Voltage sweep: none
Device settings
connected.
154 OMICRON
Spare Bushing tests
Table 14-3: Spare Bushing PF/DF/Tanδ & CAP – C1 test settings (continued)
Setting Description
Test conditions
Correction factors
correction.
The following table describes the Spare Bushing PF/DF/Tanδ & CAP – C1 measurement data.
Table 14-4: Spare Bushing PF/DF/Tanδ & CAP – C1 measurement data
Data Description
V test Test voltage
DF meas/
Tanδ meas1
OMICRON 155
Table 14-4: Spare Bushing PF/DF/Tanδ & CAP – C1 measurement data (continued)
Data Description
DF corr/
Tanδ corr1
DF ref/
Tanδ ref1
156 OMICRON
Spare Bushing tests
14.3 Spare Bushing PF/DF/Tanδ & CAP – C2 test

The following table describes the Spare Bushing PF/DF/Tanδ & CAP – C2 test settings.
Table 14-5: Spare Bushing PF/DF/Tanδ & CAP – C2 test settings
Setting Description
Device settings
connected.
Test conditions
Correction factors
correction.
The following table describes the Spare Bushing PF/DF/Tanδ & CAP – C2 measurement data.
Table 14-6: Spare Bushing PF/DF/Tanδ & CAP – C2 measurement data
Data Description
V test Test voltage
OMICRON 157
Table 14-6: Spare Bushing PF/DF/Tanδ & CAP – C2 measurement data (continued)
Data Description
DF meas/
Tanδ meas1
DF corr/
Tanδ corr1
DF ref/
Tanδ ref1
158 OMICRON
Spare Bushing tests
14.4 Spare Bushing PF/DF/Tanδ & CAP – C1+C2 test

The following table describes the Spare Bushing PF/DF/Tanδ & CAP – C1+C2 test settings.
Table 14-7: Spare Bushing PF/DF/Tanδ & CAP – C1+C2 test settings
Setting Description
Device settings
connected.
Test conditions
Correction factors
correction.
The following table describes the Spare Bushing PF/DF/Tanδ & CAP – C1+C2 measurement data.
Table 14-8: Spare Bushing PF/DF/Tanδ & CAP – C1+C2 measurement data
Data Description
V test Test voltage
OMICRON 159
Table 14-8: Spare Bushing PF/DF/Tanδ & CAP – C1+C2 measurement data (continued)
Data Description
DF meas/
Tanδ meas1
DF corr/
Tanδ corr1
160 OMICRON
Spare Bushing tests
14.5 Spare Bushing – Energized Collar test

The following table describes the Spare Bushing – Energized Collar test settings.
Table 14-9: Spare Bushing – Energized Collar test settings
Setting Description
Device settings
connected.
Test conditions
Correction factors
The following table describes the Spare Bushing – Energized Collar measurement data.
Table 14-10: Spare Bushing – Energized Collar measurement data
Data Description
V test Test voltage
OMICRON 161
Table 14-10: Spare Bushing – Energized Collar measurement data (continued)
Data Description
162 OMICRON
Circuit breaker tests
15 Circuit breaker tests

In this chapter, the settings and measurement data of the circuit breaker tests are described. Fore more
system.
Primary Test Manager supports the following circuit breaker tests:
• Circuit Breaker PF/DF/Tanδ1 & CAP
• Bushing PF/DF/Tanδ1 & CAP – C1
• Bushing PF/DF/Tanδ1 & CAP – C2
• Bushing – Energized Collar
• Contact Resistance
OMICRON 163
15.1 Circuit Breaker PF/DF/Tanδ & CAP test

The following table describes the Circuit Breaker PF/DF/Tanδ & CAP test settings.
Table 15-1: Circuit Breaker PF/DF/Tanδ & CAP test settings
Setting Description
Test frequency Frequency of the test
Sweep settings
templates
profile.
tests.
• Frequency sweep: None
Device settings
connected.
164 OMICRON
Table 15-1: Circuit Breaker PF/DF/Tanδ & CAP test settings (continued)
Setting Description
Test conditions
Custom test conditions Select the Custom test conditions check box to set the test
conditions different from the global test conditions.
Correction factors
correction.
The following table describes the Circuit Breaker PF/DF/Tanδ & CAP measurement data.
Table 15-2: Circuit Breaker PF/DF/Tanδ & CAP measurement data
Data Description
Measurement Tested insulation
Position Contact position of the breaker
V test Test voltage
DF meas/
Tanδ meas1
DF corr/
Tanδ corr1
OMICRON 165
15.2 Bushing PF/DF/Tanδ & CAP – C1 test

The following table describes the Bushing PF/DF/Tanδ & CAP – C1 test settings.
Table 15-3: Bushing PF/DF/Tanδ & CAP – C1 test settings
Setting Description
Sweep settings
templates
profile.
tests.
• Frequency sweep: None
Device settings
connected.
166 OMICRON
Table 15-3: Bushing PF/DF/Tanδ & CAP – C1 test settings (continued)
Setting Description
Test conditions
Custom test conditions Select the Custom test conditions check box if you want to set test
conditions different from the job conditions.
Correction factors
correction.
The following table describes the Bushing PF/DF/Tanδ & CAP – C1 measurement data.
Table 15-4: Bushing PF/DF/Tanδ & CAP – C1 measurement data
Data Description
V test Test voltage
DF meas/
Tanδ meas1
DF corr/
Tanδ corr1
OMICRON 167
15.3 Bushing PF/DF/Tanδ & CAP – C2 test

The following table describes the Bushing PF/DF/Tanδ & CAP – C2 test settings.
Table 15-5: Bushing PF/DF/Tanδ & CAP – C2 test settings
Setting Description
Device settings
connected.
Test conditions
Correction factors
correction.
The following table describes the Bushing PF/DF/Tanδ & CAP – C2 measurement data.
Table 15-6: Bushing PF/DF/Tanδ & CAP – C2 measurement data
Data Description
V test Test voltage
168 OMICRON
Table 15-6: Bushing PF/DF/Tanδ & CAP – C2 measurement data (continued)
Data Description
DF meas/
Tanδ meas1
DF corr/
Tanδ corr1
OMICRON 169
15.4 Bushing – Energized Collar test

The following table describes the Bushing – Energized Collar test settings.
Table 15-7: Bushing – Energized Collar test settings
Setting Description
Device settings
connected.
Test conditions
Correction factors
The following table describes the Bushing – Energized Collar measurement data.
Table 15-8: Bushing – Energized Collar measurement data
Data Description
V test Test voltage
170 OMICRON
Table 15-8: Bushing – Energized Collar measurement data (continued)
Data Description
15.5 Insulating Fluids PF/DF/Tanδ & CAP test

The following table describes the Insulating Fluids PF/DF/Tanδ & CAP test settings.
Table 15-9: Insulating Fluids PF/DF/Tanδ & CAP test settings
Setting Description
Device settings
connected.
Test conditions
Oil temperature Temperature of the oil
Correction factors
correction.
OMICRON 171
The following table describes the Insulating Fluids PF/DF/Tanδ & CAP measurement data.
Table 15-10: Insulating Fluids PF/DF/Tanδ & CAP measurement data
Data Description
Specimen Oil sample under test
V Test Test voltage
DF meas/
Tanδ meas1
DF corr/
Tanδ corr1
15.6 Contact Resistance test

The following table describes the Contact Resistance test settings.
Table 15-11: Contact Resistance test settings
Setting Description
Test current Test current
Manual input of V DC Select the Manual input of V DC check box to enter the V DC
manually instead of measuring it.
Automatic result Select the Automatic result check box to stop the measurement
automatically depending on the tolerance R dev and the settling time.
the settling time
measurement stops.
172 OMICRON
Table 15-11: Contact Resistance test settings (continued)
Setting Description
Test conditions
Assessment settings
NOTICE

2. In the Edit automatic assessment limits dialog box, enter the absolute or relative limits.
The following table describes the Contact Resistance measurement data.
Table 15-12: Contact Resistance measurement data
Data Description
Main contact Main contact of the circuit breaker under test
OMICRON 173
Table 15-12: Contact Resistance measurement data (continued)
Data Description
R min Minimum assessment limit
R max Maximum assessment limit
Note: If you did not select the Automatic result check box to stop the measurement automatically, you
can stop the measurement by clicking the Keep results button.
174 OMICRON
Current transformer tests
16 Current transformer tests

In this chapter, the settings and measurement data of the current transformer tests are described. Fore
more information about testing with the CPC 100, see the CPC 100 User Manual shipped with your test
system.
Primary Test Manager supports the following current transformer tests:
• CT PF/DF/Tanδ1 & CAP
• CT Ratio
• CT Winding Resistance Sec
• CT Excitation2
• CT Ratio V
• CT Burden
• CT Composite Error
Additionally, Primary Test Manager supports the TanDelta – PF/DF/Tanδ & CAP manual test.

2. Only available for IEC 60044 and IEEE C57.13
OMICRON 175
16.1 CT PF/DF/Tanδ & CAP

The following table describes the CT PF/DF/Tanδ & CAP test settings.
Table 16-1: CT PF/DF/Tanδ & CAP test settings
Setting Description
Test frequency Frequency of the output signal
HV-shield connectable Select the HV-shield connectable check box if the HV screen or shield
of the current transformer is accessible.
Sweep settings
templates
profile.
tests.
• Frequency sweep: OMICRON
Sweep settings
176 OMICRON
Table 16-1: CT PF/DF/Tanδ & CAP test settings (continued)
Setting Description
two values.
Device settings
connected.
Test conditions
CT oil temperature Oil temperature of the current transformer
Correction factors
correction.
The following table describes the CT PF/DF/Tanδ & CAP measurement data.
Table 16-2: CT PF/DF/Tanδ & CAP measurement data
Data Description
V test Test voltage
OMICRON 177
Table 16-2: CT PF/DF/Tanδ & CAP measurement data (continued)
Data Description
DF meas/
Tanδ meas1
DF corr/
Tanδ corr1
16.2 CT Ratio
The following table describes the CT Ratio test settings.
DANGER
► When injecting current into the CT’s primary winding, make sure that no other
secondary windings are open.
Table 16-3: CT Ratio test settings
Setting Description
CPC output Selected output range for the current transformer test
Manual measurement I sec Select the Manual measurement I sec check box to enter the I sec
manually, for example, if I sec was measured with an external current
clamp not connected to the CPC 100.
Use current clamp Select the Use current clamp check box if you want to use current
clamp.
I clamp Current of the clamp
Clamp factor Ratio of the clamp
Assessment settings
178 OMICRON
NOTICE

2. In the Edit automatic assessment limits dialog box, enter the assessment limits.
The following table describes the CT Ratio measurement data.
Table 16-4: CT Ratio measurement data
Data Description
Tap Identification of the tap under test
Ipn1/Ipr2 Rated primary current of the current transformer
Isn1/Isr2 Rated secondary current of the current transformer

Auto Select the Auto check box to stop the measurement automatically.
Otherwise, the result is saved when you press Keep results.
I test Test current at the primary side of the current transformer
Frequency Frequency of the output signal
I prim Measured current at the primary side of the current transformer
I sec Measured secondary current of the current transformer
Ratio Measured ratio of the current transformer
Ratio dev Deviation of the measured ratio from the rated ratio
Phase Measured phase displacement between the primary and secondary
current
OMICRON 179
Table 16-4: CT Ratio measurement data (continued)
Data Description
Polarity Polarity status
Measure burden Select the Measure burden check box to measure the connected
secondary burden in VA.
Manual input V sec Select the Manual input V sec check box to enter the measured
secondary voltage at the burden manually, for example, if it is measured
with an external device.
V sec Measured secondary voltage on the burden
Burden Measured burden in VA related to the rated secondary current
Burden nom. Rated power of the current transformer
Phase burden Phase angle of the complex secondary burden
cos φ Phase angle of the complex rated secondary burden
180 OMICRON
16.3 CT Winding Resistance Sec

The following table describes the CT Winding Resistance Sec test settings.
DANGER
► Never open the measuring circuit while current flows.
► Make sure that no other secondary windings are open.
► Check whether the red warning light “I” and the discharge LED are off before
disconnecting the device under test.
► Before disconnecting from the CPC 100, connect the device under test on both ends
to protective earth.
Table 16-5: CT Winding Resistance Sec test settings
Setting Description
Temperature compensation for Cu
Reference temperature Reference temperature to be used for temperature correction
Note: The transformer’s core is magnetized after the measurement. Demagnetization can be done using
the CTExcitation test (see 16.4 "CT Excitation" on page 182).
Table 16-6: CT Winding Resistance Sec measurement data
Setting Description

CPC output Selected output range for the current transformer test
I test Test current
OMICRON 181
16.4 CT Excitation
The following table describes the CT Excitation test settings.
Note: The CT Excitation test is only available for current transformers conforming to IEC 60044 and
IEEE C57.13.
DANGER
Feeding test voltage to a tap of a CT can cause life-threatening voltages on other taps
with higher ratios.
► Do not touch tapped windings.
Table 16-7: CT Excitation test settings
Setting Description
Noise suppression Select the Noise suppression check box to activate an interference
filter.
Table 16-8: CT Excitation measurement data
Setting Description
Ipn Rated primary current of the current transformer
Isn Rated secondary current of the current transformer
I max Maximum test current
V max Maximum test voltage
I knee Knee point current
V knee Knee point voltage
Knee point calculation Method used for the knee point calculation
► Click the Plot tab to view the excitation curve diagram.
► Use the Tab check boxes to hide/unhide individual curves.
182 OMICRON
16.5 CT Ratio V
The following table describes the CT Ratio V test settings.
DANGER
Feeding test voltage to a tap of a CT can cause life-threatening voltages on other taps
with higher ratios.
► Do not touch tapped windings.
Table 16-9: CT Ratio V test settings
Setting Description
Table 16-10: CT Ratio V measurement data
Setting Description

V test Test voltage
V sec Measured secondary voltage
V prim Measured primary voltage
Ratio Measured ratio of the current transformer
current
Note: If the transformer’s knee point voltage is approximated or exceeded due to the transformer’s
saturation, the measurement results are not correct anymore. If the knee point is significantly exceeded,
the transformer can even be damaged. Therefore, the knee point voltage should be known or measured
beforehand. Generally, it is advisable to set the test voltage to 75 % of the knee-point voltage. The
frequency should be set between 15 and 20 Hz off the mains frequency to avoid interferences by life
systems in the neighborhood.
OMICRON 183
16.6 CT Burden
The following table describes the CT Burden test settings.
Table 16-11: CT Burden – Settings and conditions
Setting Description
The following table describes the CT Burden measurement data.
Table 16-12: CT Burden measurement data
Setting Description

I test Test current
I meas Measured burden current
V meas Measured burden voltage
Phase Measured phase displacement
Burden (@ Itest) Burden based on Itest
Burden (@ Isn1/Isr2) Burden based on Isn1/Isr2
cosφ Cos φ of phase angle
184 OMICRON
16.7 CT Composite Error

The CT Composite Error test is only available for protection CTs (class C, K or T) according to
IEEE C57.13.
Note: The transformer’s core is magnetized after the Winding Resistance measurement. Since the
core is demagnetized in the course of the CT Excitation test, we recommend performing the Winding
Resistance measurement first (see 16.4 "CT Excitation" on page 182).
Table 16-13: CT Composite Error – Settings and conditions
Setting Description
CT Excitation Measurement Settings
Noise suppression Select the check box to activate an interference filter.
CT Winding Resistance Sec Measurement Settings
Perform winding resistance Activate the check box to perform a supplementary winding resistance
measurement measurement (optional for IEEE C57.13).
Temperature compensation for Cu1
Reference temperature Reference temperature to be used for temperature correction
Assessment settings
Manual Select for manual assessment of the measurement results
Automatic According to IEEE C57.13 the measurement will be assessed as failed
if:
Composite error @ Isr > 3 %
or
Composite error @ 20 x Isr > 10 %.
1. Only available if Perform winding resistance measurement check box is activated
Table 16-14: CT Composite Error – Winding resistance measurement1
Setting Description
Ipr Rated primary current of the current transformer
Isr Rated secondary current of the current transformer
I test Test current at the primary side of the current transformer
OMICRON 185
Table 16-14: CT Composite Error – Winding resistance measurement1 (continued)
Setting Description
1. Only available if Perform winding resistance measurement check box is activated
Table 16-15: CT Composite Error – Excitation curve measurement
Setting Description
I max Maximum test current
V max Maximum test voltage
I knee Knee point current
V knee Knee point voltage
Knee point calculation Method used for the knee point calculation
Table 16-16: CT Composite Error – Composite error
Setting Description
Composite error @ Isr Composite error at rated secondary current
Calculated on the basis of the excitation curve measurement and the
asset’s Isr and Vb values.
Composite error @ 20 x Isr Composite error at 20 x rated secondary current
186 OMICRON
Voltage transformer tests
17 Voltage transformer tests

In this chapter, the settings and measurement data of the voltage transformer tests are described. Fore
more information about testing with the CPC 100, see the CPC 100 User Manual shipped with your test
system.
Primary Test Manager supports the following voltage transformer tests:
• VT PF/DF/Tanδ1 & CAP2
• VT Ratio
• VT Burden
Additionally, Primary Test Manager supports the TanDelta – PF/DF/Tanδ & CAP manual test.
17.1 VT PF/DF/Tanδ & CAP test

Note: This test is identical to the PF/DF/Tanδ & CAP test for current transformers. Refer to 16.1 "CT
PF/DF/Tanδ & CAP" on page 176.
17.2 VT Ratio test

The following table describes the VT Ratio test settings.
DANGER
► Do not connect the CPC 100 output to the secondary side of the VT. This will lead to
hazardous voltages on the primary side.
► For VT ratio measurement, connect the CPC 100 output to the primary side of the VT.
The following table describes the VT Ratio measurement data.
Table 17-1: VT Ratio measurement data
Data Description
Upn Rated primary voltage of the voltage transformer
Usn Rated secondary voltage of the voltage transformer
V test Test voltage at the primary side of the voltage transformer
Test frequency Test frequency of the output signal

2. Only available for inductive voltage transformers
OMICRON 187
Table 17-1: VT Ratio measurement data (continued)
Data Description
V prim Measured voltage at the primary side of the voltage transformer
V sec Measured secondary voltage of the voltage transformer
Ratio Measured ratio of the voltage transformer
voltage
17.3 VT Burden test

The following table describes the VT Burden test settings.
Table 17-2: VT Burden test settings
Setting Description
Table 17-3: VT Burden measurement data
Setting Description
Upn Rated primary voltage of the voltage transformer
Usn Rated secondary current of the voltage transformer
V test Test voltage
V meas Measured burden voltage
I meas Measured burden current
Phase Measured phase displacement
Burden (@ Vtest) Burden based on Vtest
Burden (@ Usn) Burden based on Usn
cosφ Cos φ of phase angle
188 OMICRON
Rotating machine tests
18 Rotating machine tests

18.1 Stator Winding PF/DF & CAP
Capacitance and power factor (PF)/dissipation factor (DF/tan δ) measurements are conducted to identify
defects that affect the condition of the machine insulation.
For a suitable test object compensation using the CP CR500, the capacitance value is required and can
be measured or entered in the Hardware configuration section of the test.
Table 18-1: Stator Winding PF/DF & CAP – Hardware configuration
Setting Description
Detect capacitance ► Click Yes if you do not know the test objects capacitance and want
to measure it before testing.
This will add the Capacitance tab to the Measurements section. In this
tab you can perform a measurement to detect the capacitance before
performing the Stator Winding test.
Capacitance of test object ► Enter the test object’s capacitance.
If you measure the capacitance before the test (see
Detect capacitance above), this field will be filled in automatically after
the measurement is completed.
Number of CP CR500 coils (at <test frequency>)
► Enter the number of available coils, depending on the number and types of CP CR500 available.
The CP CR500 comes with one of the following inductor combinations:
a) 2 x 40 H
b) 1 x 40 + 1 x 80 H
c) 2 x 80 H
Example:
1 x CP CR500 type a
1 x CP CR500 type b
= inductances of 3 x 40 H and 1 x 80 H
If freq. = 50 Hz, test capacitance = 250 nF and max. Vtest = 10 kV:
Primary Test Manager recommendation: connection of 1 x 40 H coil.
OMICRON 189
Table 18-2: Stator Winding PF/DF & CAP – Settings and conditions
Setting Description
Test frequency ► Enter the test frequency.
This value is also used for the calculation of the necessary number of
CP CR500 coils.
Sweep settings
Sweep profiles ► Click the pen button to create a voltage sweep profile.
► Add up to 30 measurement points with individual output voltages.
Double-click a value to change it.
tests.
Note: The predefined profiles cannot be edited or deleted.
The default voltage sweep profile is OMICRON expertise.
Device settings
Enable shield check ► Activate the check box if you want the CPC 100 to check whether the
shield of the high-voltage cable is connected.
Use beeper ► Select the Use beeper check box if you want to use the CP TD1’s
Test conditions
Custom test conditions ► Activate the check box to set test conditions differing from the global
test conditions.
Winding temperature Temperature of the machine’s winding
190 OMICRON
Rotating machine tests
Table 18-3: Stator Winding PF/DF & CAP – Measurements
Setting Description
Capacitance1
Measurement Measurement procedure
Test mode Test mode according to IEEE Std 62-1995
Sweep Disabled for the capacitance measurement
V test Test voltage
I tot Measured current in the parallel resonance circuit
PF meas/ Measured power factor/dissipation factor
DF meas2, 3
Cap. meas3 Measured capacitance
Measurements
Measurement Measurement procedure
Test mode Test mode according to IEEE Std 62-1995
Sweep Setting selected under Sweep settings
V test Test voltage
PF meas/ Measured power factor/dissipation factor
DF meas2, 3
Cap. meas3 Measured capacitance
1. Only available if Detect capacitance is set to Yes.
2. Depending on the standard selected in the Primary Test Manager settings (see 4.1.1 "Settings" on page 19)
3. According to IEC 60034-27-33 and IEEE 286
OMICRON 191
19 Grounding system tests

In this chapter, the settings and measurement data of the grounding system tests are described. For
more information about safe testing with the HGT1 and the CPC 100, refer to the respective User
Manuals.
► For information on the grounding system and the corresponding maps, refer to 12.7 "Grounding
system" on page 103.
► For information about the Location settings used for grounding system tests, refer to the Settings
section "General" on page 20.
19.1 Ground impedance measurement

Table 19-1: Ground impedance measurement – Settings and conditions
Setting Description
Frequency Frequency of the input signal
Current Input current
Reduction factor Value specific to the site
► Measure the reduction factor on site or enter 1 as the worst-case
value.
Input source OMICRON input device with or without accessories
► To mark the injection line on the map, press Draw injection line.
Table 19-2: Ground impedance measurement – Measurements
Setting Description
Distance Distance to the reference point
Voltage Voltage at nominal frequency
Details
Z Impedance at nominal frequency
VStep Step voltage
V Voltage
192 OMICRON
Grounding system tests
19.2 Step&Touch voltage measurement

Table 19-3: Step&Touch voltage measurement – Settings and condtions
Setting Description
Frequency Frequency of the input signal
Current Input current
Reduction factor Value specific to the site
► Measure the reduction factor on site or enter 1 as the worst-case
value.
Add. considered resistance Additional resistance considered for the measurement (e. g. clothes,
floor conditions), depending on the applicable standard
Standard Standard applicable for the measurement
Body current limit acc.1 Standard applicable for the body current limit
Input source OMICRON input device with or without accessories
Req. input impedance
Perm. body current
Perm. touch voltage
Required/permitted values depending on the settings above
Perm. step voltage1
Perm. hand-to-hand
voltage1
1. Only for Standard IEEE 80/81
► To mark the injection line on the map, press Draw injection line.
Table 19-4: Step&Touch voltage measurement – Measurements
Setting Description
Location Id Location number for reporting
Location Description field for the measurement location
Input impedance Input impedance on the HGT1
Scenario Type of measurement per measurement point
Permissible touch voltage
Permissible step voltage Required/permitted values depending on the Settings and conditions
(Table 19-3 above)
Permissible hand-to-hand
touch voltage
Voltage Voltage at nominal frequency
OMICRON 193
20 Optional manual tests

In this chapter, the settings and measurement data of the optional manual tests supported by Primary
Test Manager are described. Fore more information about testing with the CPC 100, see the CPC 100
User Manual shipped with your test system.
The optional manual test are asset-independent. You can perform the tests for any asset described in
this User Manual, but Primary Test Manager does not guide you through the tests and provides no test
settings data.
DANGER
Wrong test settings and/or a faulty test procedure may damage the test set and the asset
under test and can result in personal injury or death of the operating staff.
► Thoroughly review planned steps and test settings before performing a manual test.
194 OMICRON
Optional manual tests
20.1 Insulation Resistance test

The Insulation Resistance test is used to import or enter data from an insulation testing device.
Table 20-1: Insulation Resistance – Settings and conditions
Setting Description
Test conditions
Test object temperature Temperature of the test object
Calculations
PI calculation Calculation of polarization index
Time 1 In the standard PI calculation, the testing device is applied and insulation
resistance measurements are taken after 60 seconds (Time 1) and 600
Time 2
seconds (Time 2).
The polarization index (PI) is calculated as follows:
R 600
PI = -----------
R 60
DAR calculation Calculation of dielectric absorption ratio

Time 1 In the standard DAR calculation, the testing device is applied and
insulation resistance measurements are taken after 30 seconds (Time 1)
Time 2
and 60 seconds (Time 2).
The dielectric absorption ratio (DAR) is calculated as follows:
R 60
DAR = --------
R 30
Correction factors
correction.
Correction temp. Temperature correction factor
OMICRON 195
Table 20-2: Insulation Resistance – Measurements
Setting Description
Test data To import a file containing test data:
► Press Add to browse your PC and add data from a file.
To directly import data from a measurement file:
► Open the file on your computer.
► In the file press CTRL+A to mark all content, then press CTRL+C to
copy.
► In Primary Test Manager press Paste from clipboard.
The results may take a few seconds to load.
Measurement Name or number of the measurement
PI Polarization index
DAR Dielectric absorption ratio
Time Time at which the given values were recorded
Voltage
Voltage and current values recorded at the Time specified in the first
V DC
column
I DC
196 OMICRON
20.2 TanDelta – PF/DF/Tanδ1 & CAP test

The following table describes the TanDelta – PF/DF/Tanδ & CAP test settings.
Table 20-3: TanDelta – PF/DF/Tanδ & CAP test settings
Setting Description
Default frequency Default test frequency
Show results Select the results you want to display from the list.
All measurement results are stored and can be displayed by selecting
them from the list.
Device settings
Enable shield check Select the Enable shield check check box if you want that the CPC 100
checks whether the shield of the high-voltage cable is connected.
Test conditions
Test object temperature Temperature of the test object
Correction factors
correction.
Use reference voltage1 Select the Use reference voltage check box to extrapolate the I out and
Watt losses results for the specified reference voltage.
Reference voltage1 Reference voltage for extrapolation of measurement results
1. Only for (PF/DF/Tanδ, Cap., watt losses) measurement results
OMICRON 197
The following tables describe the TanDelta – PF/DF/Tanδ & CAP measurement data.
Table 20-4: TanDelta – PF/DF/Tanδ & CAP common measurement data
Data Description
No.1 Number of the measurement
Measurement2 Arrangement of the measurement

V test Test voltage
1. A value is assigned after a measurement has been added.
2. The data is by default empty. You can type your own measurement name.
Note: To add a measurement point to a measurement, click Add meas. point. To add a measurement
to the TanDelta – PF/DF/Tanδ & CAP test, click Add measurement.
Table 20-5: TanDelta – PF/DF/Tanδ & CAP common measurement data (PF/DF/Tanδ, Cap., watt
losses)
Data Description
DF meas/
Tanδ meas1
DF corr/
Tanδ corr1
198 OMICRON
Table 20-6: TanDelta – PF/DF/Tanδ & CAP measurement data (Imp. Z)
Data Description
Z phase Phase of the measured impedance
Z abs Magnitude of the measured impedance
Table 20-7: TanDelta – PF/DF/Tanδ & CAP measurement data

(Q power, S power)
Data Description
Reactive power Measured reactive power Q
Apparent power Measured apparent power S
Table 20-8: TanDelta – PF/DF/Tanδ & CAP measurement data (Cp, Rp)
Data Description
Cp Measured parallel capacitance
Rp Measured parallel resistance

(Cp, quality factor)
Data Description
Cp Measured parallel capacitance
Quality factor Measured quality factor
Table 20-10: TanDelta – PF/DF/Tanδ & CAP measurement data (Ls, Rs)
Data Description
Ls Measured series inductance
Rs Measured series resistance

(Ls, quality factor)
Data Description
Ls Measured series inductance
Quality factor Measured quality factor
OMICRON 199
Support
When you are working with our products we want to provide you with the greatest
possible benefits. If you need any support, we are here to assist you!
24/7 Technical support – get support

www.omicronenergy.com/support
At our technical support hotline, you can reach well-educated technicians for all
of your questions. Around the clock – competent and free of charge.
Make use of our 24/7 technical support hotlines:
Americas: +1 713 830-4660 or +1 800-OMICRON
Asia-Pacific: +852 3767 5500
Europe / Middle East / Africa: +43 59495 4444
Additionally, you can find our Service Center or Sales Partner closest to you at
www.omicronenergy.com.
Customer area – stay informed

www.omicronenergy.com/customer
The customer area on our website is an international knowledge exchange
platform. Download the latest software updates for all products and share your
own experiences in our user forum.
Browse through the knowledge library and find application notes, conference
papers, articles about daily working experiences, user manuals and much more.
OMICRON Academy – learn more

www.omicronenergy.com/academy
Learn more about your product in one of the training courses offered by the
OMICRON Academy.
OMICRON electronics GmbH, Oberes Ried 1, 6833 Klaus, Austria, +43 59495
200 OMICRON
ENU 1036 06 05

CPC 100 PTM User Manual Enu

Uploaded by

Copyright:

Available Formats

CPC 100 PTM User Manual Enu

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CPC 100 PTM User Manual Enu

Uploaded by

Copyright:

Available Formats

What safety instructions are mentioned?

What safety instructions are mentioned?

What are the main components of the test set described?

What are the main components of the test set described?

CPC 100 PTM

Manual Version: ENU 1036 06 05

5.4.6 Current transformer view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

13.1.4 Bushing H/X PF/DF/Tanδ & CAP – C2 test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

About this manual

Conventions and symbols used

1.1 Operator qualifications and safety standards

1.2 Orderly measures

Characteristic Requirement (*recommended)

3.1 The test set

Figure 3-1: Front view of the CPC 100

Figure 3-2: Right-side view of the CPC 100

3.2 Installing Primary Test Manager

3.3 Starting Primary Test Manager and connecting to the

3.3.2 Starting via the CPC Start Page

Figure 3-3: CPC start page

3.3.3 Connecting to the CPC 100

Figure 3-4: Connecting to CPC 100

3.3.4 Updating the CPC 100 embedded software

Updating via PTM Home view

Updating via device browser

3.3.5 Open the device web interface

3.4 Primary Test Manager licensing

Table 3-1: Primary Test Manager licenses

Figure 4-1: Primary Test Manager home view

Table 4-1: Data importance categories

Balloon Category Description

Recommended Indicates data supporting the Primary Test Manager workflows.

Information Contains descriptive information.

Primary Test Manager supports the following user tasks.

Button Description Action

Click to start the guided test workflow

Click to execute a prepared job

Click to open the Manage view for locations, assets, jobs,

Click to create a new manual test

Click to open a manual test

4.1 Title bar

Table 4-3: Title bar commands

Figure 4-2: General tab

Table 4-4: Logging levels

Logging level Description

Figure 4-3: Profiles tab

Figure 4-4: Profiles tab: Transformer

Profiles: Circuit breaker

Figure 4-5: Profiles tab: Circuit breaker

Profiles: Current transformer

Figure 4-6: Profiles tab: Current transformer

7. Click OK to close the Settings dialog box.

Figure 4-7: Templates tab

Figure 4-8: Databases tab

Figure 4-9: Help dialog box

Figure 4-10: About Primary Test Manager dialog box

4.2 Status bar

Table 4-5: Test system statuses

CPC 100 connected