Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
625 views

Compressive Strength of Concrete Cube

The compressive strength test of concrete cubes is used to determine if concrete was properly mixed and cured. It involves casting 15cm cubes of wet concrete and testing them after 7 and 28 days of curing in water. The test procedure involves gradually applying a compressive load to crushed cubes in a compression testing machine, and calculating compressive strength by dividing the maximum load by the cross-sectional area. The results are used to check if the concrete meets the specified compressive strength requirements for the grade of concrete used in construction.

Uploaded by

Pawan Patil
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
625 views

Compressive Strength of Concrete Cube

The compressive strength test of concrete cubes is used to determine if concrete was properly mixed and cured. It involves casting 15cm cubes of wet concrete and testing them after 7 and 28 days of curing in water. The test procedure involves gradually applying a compressive load to crushed cubes in a compression testing machine, and calculating compressive strength by dividing the maximum load by the cross-sectional area. The results are used to check if the concrete meets the specified compressive strength requirements for the grade of concrete used in construction.

Uploaded by

Pawan Patil
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

Compressive strength of concrete cube test provides an idea about all the

characteristics of concrete. By this single test one judge that whether Concreting
has been done properly or not. Concrete compressive strength for general
construction varies from 15 MPa (2200 psi) to 30 MPa (4400 psi) and higher in
commercial and industrial structures.

Compressive strength of concrete depends on many factors such as


water-cement ratio, cement strength, quality of concrete material, quality
control during production of concrete etc.

Test for compressive strength is carried out either on cube or cylinder.


Various standard codes recommends concrete cylinder or concrete cube
as the standard specimen for the test. American Society for Testing
Materials ASTM C39/C39M provides Standard Test Method for

Compressive Strength Definition


Compressive strength is the ability of material or structure to carry the
loads on its surface without any crack or deflection. A material under
compression tends to reduce the size, while in tension, size elongates.

Compressive Strength Formula


Compressive strength formula for any material is the load applied at the
point of failure to the cross-section area of the face on which load was
applied.

Compressive Strength = Load / Cross-sectional Area

Procedure: Compressive Strength Test of Concrete Cubes


For cube test two types of specimens either cubes of 15cm X 15cm X
15cm or 10cm X 10cm x 10cm depending upon the size of aggregate are
used. For most of the works cubical moulds of size 15cm x 15cm x 15cm
are commonly used.
This concrete is poured in the mould and tempered properly so as not to
have any voids. After 24 hours these moulds are removed and test
specimens are put in water for curing. The top surface of these specimen
should be made even and smooth. This is done by putting cement paste
and spreading smoothly on whole area of specimen.

These specimens are tested by compression testing machine after 7 days


curing or 28 days curing. Load should be applied gradually at the rate of
140 kg/cm2 per minute till the Specimens fails. Load at the failure divided
by area of specimen gives the compressive strength of concrete.

Following are the procedure for testing Compressive strength of Concrete Cubes
Apparatus for Concrete Cube Test
Compression testing machine

Preparation of Concrete Cube Specimen


The proportion and material for making these test specimens are from the
same concrete used in the field.

Specimen
6 cubes of 15 cm size Mix. M15 or above
Mixing of Concrete for Cube Test
Mix the concrete either by hand or in a laboratory batch mixer

Hand Mixing
1. Mix the cement and fine aggregate on a water tight none-absorbent
platform until the mixture is thoroughly blended and is of uniform color
2. Add the coarse aggregate and mix with cement and fine aggregate until
the coarse aggregate is uniformly distributed throughout the batch
3. Add water and mix it until the concrete appears to be homogeneous and
of the desired consistency

Sampling of Cubes for Test


1. Clean the mounds and apply oil
2. Fill the concrete in the molds in layers approximately 5 cm thick
3. Compact each layer with not less than 35 strokes per layer using a
tamping rod (steel bar 16mm diameter and 60cm long, bullet pointed at
lower end)
4. Level the top surface and smoothen it with a trowel

Curing of Cubes
The test specimens are stored in moist air for 24 hours and after this
period the specimens are marked and removed from the molds and kept
submerged in clear fresh water until taken out prior to test.

Precautions for Tests


The water for curing should be tested every 7 days and the temperature
of water must be at 27+-2oC.

Procedure for Concrete Cube Test


1. Remove the specimen from water after specified curing time and wipe out
excess water from the surface.
2. Take the dimension of the specimen to the nearest 0.2m
3. Clean the bearing surface of the testing machine
4. Place the specimen in the machine in such a manner that the load shall be
applied to the opposite sides of the cube cast.
5. Align the specimen centrally on the base plate of the machine.
6. Rotate the movable portion gently by hand so that it touches the top
surface of the specimen.
7. Apply the load gradually without shock and continuously at the rate of
140 kg/cm2/minute till the specimen fails
8. Record the maximum load and note any unusual features in the type of
failure.

Note:
Minimum three specimens should be tested at each selected age. If
strength of any specimen varies by more than 15 percent of average
strength, results of such specimen should be rejected. Average of three
specimens gives the crushing strength of concrete. The strength
requirements of concrete.

Calculations of Compressive Strength


Size of the cube =15cmx15cmx15cm

Area of the specimen (calculated from the mean size of the specimen
)=225 cm2
Characteristic compressive strength(f ck)at 7 days =

Expected maximum load =fck x area x f.s

Range to be selected is …………………..

Similar calculation should be done for 28 day compressive strength

Maximum load applied =……….tones = ………….N

Compressive strength = (Load in N/ Area in mm2)=……………N/mm2


=……………………….N/mm2
Reports of Cube Test
1. Identification mark
2. Date of test
3. Age of specimen
4. Curing conditions, including date of manufacture of specimen
5. Appearance of fractured faces of concrete and the type of fracture if they are
unusual

Results of Concrete Cube Test


Average compressive strength of the concrete cube = ………….N/ mm2 (at
7 days)
Average compressive strength of the concrete cube =………. N/mm2 (at 28
days)
Compressive Strength of Concrete at Various Ages
The strength of concrete increases with age. Table shows the strength of
concrete at different ages in comparison with the strength at 28 days
after casting.

Age Strength percent

1 day 16%

3 days 40%

7 days 65%

14 days 90%

28 days 99%

Compressive Strength of Different Grades of Concrete at


7 and 28 Days
Grade of Minimum compressive strength Specified characteristic compressive strength (N/mm
Concrete N/mm2 at 7 days at 28 days

M15 10 15

M20 13.5 20

M25 17 25

M30 20 30

M35 23.5 35
M40 27 40

M45 30 45

You might also like