Govt.

Advance Technical Training Center Peshawar

Assigment#7/M3-1
Submission Date: __________
Q No.1 Draw the following figures using 3D basic Shapes and Edit Commands.

Q No.2 Draw the figure using Extrude with solid.

Q No. 3 Draw the figure using Extrude with surface along the path.

Tips: use join Command

Page 1 of 20
 Govt. Advance Technical Training Center Peshawar
AutoCAD 6 months CBT Course (NAVTTC Program) 2017

Q No.4 Design a polygon with 5 sides which is inscribed along a circle of radius 5 and
extrudes it along a tapper angle of 45 degrees and with an extrusion height of 3.

Page 2 of 20
 Govt. Advance Technical Training Center Peshawar
AutoCAD 6 months CBT Course (NAVTTC Program) 2017

Assignment No. 08/M3-2

Q No. 1

Make a Glass Using Revolve command.

Hints: profile to used and final result are shown below in figure.

Page 3 of 20
 Govt. Advance Technical Training Center Peshawar
AutoCAD 6 months CBT Course (NAVTTC Program) 2017

Assignment No. 9/M3-3

Q1: Take a cylinder with central point of (0,0,0), radius of 4 units and height of 4, combine this
cylinder with a cone having central point of (0,0,2), radius of 3 and height of 10 units.

Q2: Subtract a cone of height 8, radius of 1.5 having central point (2, 0, 0) from a box of
dimension 4x4x4 with lover left corner at (0,0,0).

Q3: Take two pyramids of Same Dimensions but different central point’s i.e. ;(0,0,0) for 1 st one
and (2,2,2) for 2nd. Take the radius of inscribed circle equal to 3 and extract the intersecting
portion of these two.

Q4: Construct a cone by assuming all the dimensions of your own and cut it into two halves
from its diameter.

Q5: Make a Cup by using 3 circles of radius 2, 2and 0.25 and an arc with radius 1.5 and length 3.
The thickness of walls of cup must be 0.1 units.(you can use alternate method but dimensions
will remain constant )

Hints: Objects to used and final result are shown below in figure.

Page 4 of 20
 Govt. Advance Technical Training Center Peshawar
AutoCAD 6 months CBT Course (NAVTTC Program) 2017

Assignment No. 10/M4-1

Question No.1

Page 5 of 20
 Govt. Advance Technical Training Center Peshawar
AutoCAD 6 months CBT Course (NAVTTC Program) 2017

Question No.2:

Page 6 of 20
 Govt. Advance Technical Training Center Peshawar
AutoCAD 6 months CBT Course (NAVTTC Program) 2017

Assignment No. 11/M8-1

Page 7 of 20
 Govt. Advance Technical Training Center Peshawar
AutoCAD 6 months CBT Course (NAVTTC Program) 2017

Assignment No. 12/M09-1

In this Assignment, you are given all dimensions in two 2D representations of the 3D object to draw. You have to
start by choosing the 2D figure to start with.
Q No. 1

Page 8 of 20
 Govt. Advance Technical Training Center Peshawar
AutoCAD 6 months CBT Course (NAVTTC Program) 2017

Q No. 2

Page 9 of 20
 Govt. Advance Technical Training Center Peshawar
AutoCAD 6 months CBT Course (NAVTTC Program) 2017

Q No. 3

Page 10 of 20
 Govt. Advance Technical Training Center Peshawar
AutoCAD 6 months CBT Course (NAVTTC Program) 2017

Q No. 4

Page 11 of 20
 Govt. Advance Technical Training Center Peshawar
AutoCAD 6 months CBT Course (NAVTTC Program) 2017

Q No.5

Q No.6

Q No.7

Page 12 of 20
 Govt. Advance Technical Training Center Peshawar
AutoCAD 6 months CBT Course (NAVTTC Program) 2017

Assignment No. 13/M09-2

Draw the following figure in AutoCAD using Knowledge from module 2 to 6.

Page 13 of 20
 Govt. Advance Technical Training Center Peshawar
AutoCAD 6 months CBT Course (NAVTTC Program) 2017

Assignment No. 14/ M09

Draw the following figures in AutoCAD. Draw profiles using any method (SECTION,
FLATSHOT, SOLVIEW, SOLDARAW or SOLPROFILE)

Page 14 of 20
Govt. Advance Technical Training Center Peshawar
AutoCAD 6 months CBT Course (NAVTTC Program) 2017

Page 15 of 20
 Govt. Advance Technical Training Center Peshawar
AutoCAD 6 months CBT Course (NAVTTC Program) 2017

Assignment No. 15/ M09

Draw the section view of all the figures of Assignment No.14

Page 16 of 20
 Govt. Advance Technical Training Center Peshawar
AutoCAD 6 months CBT Course (NAVTTC Program) 2017

Assignment No. 16/ M09

Using free Hand Sketching and Sketch the Following figures on Plane sheet
Submission Date: ____________ Total Marks: 10

Page 17 of 20
 Govt. Advance Technical Training Center Peshawar
AutoCAD 6 months CBT Course (NAVTTC Program) 2017

Assignment No. 17/ M09

Using Tools drawing and draw the following figures on Graph paper
Submission Date: ____________ Total Marks: 10

Isometric view

Page 18 of 20
Govt. Advance Technical Training Center Peshawar
AutoCAD 6 months CBT Course (NAVTTC Program) 2017

Oblique View

Assignment No. 18/ M09

Page 19 of 20
 Govt. Advance Technical Training Center Peshawar
AutoCAD 6 months CBT Course (NAVTTC Program) 2017

Submission Date: ____________ Total Marks: 10

Using figure of Project N0-3 (3D project part-1) as shown below and draw its
Elevations using AutoCAD and freehand sketching

Page 20 of 20