See discussions, stats, and author profiles for this publication at: https://www.researchgate.

net/publication/263025546

Design and implementation of a Fiber to the Home FTTH access network

based on GPON

Article  in  International Journal of Computer Applications · March 2014

DOI: 10.5120/16015-5050

CITATIONS READS

7 4,202

1 author:

Mahmoud Al-Quzwini
New Jersey Institute of Technology
9 PUBLICATIONS   14 CITATIONS   

SEE PROFILE

All content following this page was uploaded by Mahmoud Al-Quzwini on 25 November 2017.

The user has requested enhancement of the downloaded file.

 International Journal of Computer Applications (0975 – 8887)
Volume 92 – No.6, April 2014

Design and Implementation of a Fiber to the Home

FTTH Access Network based on GPON

Mahmoud M. Al-Quzwini
College of Engineering, Al-Nahrain University, Baghdad, Iraq

ABSTRACT Wavelength Division Multiplexing Passive Optical Networks

This paper presents a step by step design and field WDM PONs are the next generation in the development of
implementation of a protected GPON FTTH access network access networks. Two flavors of WDM-PON are being
serving 1000 users. The basic components of the network are studied by Study Group 15 (SG15) of the International
presented and the contribution of each component to the Telecommunication Union–Telecommunication
architecture of the FTTH network is addressed. The design Standardization Sector (ITU–T) [15]. The first one is time
incorporates Class B protection, to provide redundancy in the and wavelength division multiplexing PON (TWDM PON)
feeder and GPON port, the practical implementation of a which transmits 4-16 wavelengths on the same fiber to
protected FTTH network is highly emphasized. support higher number of users per fiber at higher
transmission rates or more importantly to allow more than one
Indexing terms/Keywords operator sharing the same fiber, i.e. Operators can work with
GPON, FTTH, broadband, Fiber Optics communications different wavelengths [15]. The second one is arrayed
waveguide grating (AWG)-based WDM-PON which aimed to
1. INTRODUCTION provide each user with a dedicated wavelength, similar to
Growing demand for high speed internet is the primary driver P2P, supporting 1.25 Gbps downstream and upstream
for the new access technologies which enable experiencing transmission capacity [15], [32].
true broadband. It leads telecommunication operators to GPON FTTH architecture offers converged data and voice
seriously consider the high volume roll-out of optical-fiber services at up to 2.5 Gbps. GPON enables transport of
based access networks. They have to renew their access multiple services in their native format, specifically TDM and
networks that are clearly becoming the bottleneck in terms of data. In order to enable easy transition from BPON to GPON,
bandwidth. Therefore most telecommunication providers are many functions of BPON are reused for GPON. The GPON
currently withdrawing their legacy copper network, giving standards are known as ITU-T Recommendations G.984.1
way to optical fiber networks. To allow faster connections, the through G.984.5. The GPON’s uses Generic Framing
optical fiber gets closer and closer to the subscriber. Fiber To Procedure (GFP) protocol to provide support for both voice
The Home FTTH appears the most suitable choice for a long and data oriented services. A big advantage of GPON over
term objective: if the clients are wholly served by optical other schemes is that interfaces to all the main services are
fibers, it will be easier to increase the bandwidth in the future provided and in GFP enabled networks packets belonging to
[2]. FTTH is future proof solution for providing broadband different protocols can be transmitted in their native formats
services such as Video on demand, Online Gaming, HD TV [29], [30]. The voice component can be represented as VOIP
and VoIP. service (voice over IP, packet-switched protocol) and can be
Passive optical network (PON) based FTTH access network is combined with data component in physical layer simulations.
a point-to-multipoint, fiber to the premises network Finally, the video component can be represented as a RF
architecture in which unpowered optical splitters are used to video signal (traditional CATV) or as IPTV signal that also
enable a single optical fiber to serve multiple premises, can be combined with data [4]
typically 32–128 [9]. Fiber to the Home networks exploit the Different aspects of FTTH access networks have been
low attenuation (0.2–0.6 dB/km) and high bandwidth discussed in literature, [1]-[10] address issues related to
(>30,000 GHz) of single mode optical fibers [12] to provide outside plant OSP, [11]-[14] consider the power efficiency of
many times more bandwidth than currently available with these networks, some issues related to the implementation
existing broadband technologies. In addition, these networks cost associated with FTTH networks are discussed in [15]-
have the ability to provide all communication services viz. [26], availability modeling of the networks are discussed in
voice, data and video from one network platform [33]. [27],[28], and [31]-[33] discuss issues and challenges related
Several Time Division Multiplexing TDM PON technologies to next generation PONs. However, the results of these
are standardized for FTTH deployments, Table 1 summarizes researches are suboptimal as they are not based on actual
these standards with their important parameters [3], [15], [21], networks. Furthermore, despite of its importance and being
[33]. The main disadvantage of TDM PON is that it not supported by the well-known OLT brands, class B protection
possible for different operators to physically share the same has not been considered in the analysis of any of these
fiber. A multi-fiber deployment is necessary to physically researches. This shortage in access network field experience
share the access network [15]. motivates the publication of this paper. Moreover, this paper
provides a hands-on experience on GPON FTTH access
networks design, validation and implementation.

30
 International Journal of Computer Applications (0975 – 8887)
Volume 92 – No.6, April 2014

Table 1. TDM PON standards

Parameter BPON EPON GPON XGPON 10G-EPON
Standard ITU-T G.983 IEEE 802.3ah ITU-T G.984 ITU-T G.987 IEEE 802.3av
Downstream data 622 Mbps 1.25 Gbps 2.5 Gbps 10 Gbps 10 Gbps
Rate
Upstream data Rate 155 Mbps 1.25 Gbps 1.25 Gbps 2.5 Gbps 10 Gbps/Symmetric
1 Gbps/Asymmetric

 high reliability
In addition to this section, the paper is organized as follows:
section 2 introduces an explanation to the basic components  support network survivability and protection policy
of a GPON FTTH access network, section three presents the
general architecture of these networks, section four discusses 2.3 Optical Network Terminal ONT
issues related to the traffic rates and flow mechanism, it also Optical Network Terminals (ONTs) are deployed at
explains in details the idea of type B protection used in GPON customer’s premises. ONTs are connected to the OLT by
FTTH access networks, section five charts the design steps means of optical fiber and no active elements are present in
and present the designed feeder network and part of the the link.
distribution network, the terminology used in addressing each
part in the network is clarified in this section as well, section In GPON the transceiver in the ONT is the physical
six discusses the procedure to validate the design of the connection between the customer premises and the central
network, section seven summarizes the implementation steps office OLT. WDM triplexer module separates the three
and finally section eight wraps up the paper with the wavelengths 1310nm, 1490nm and 1550nm (for CATV
important conclusions. service). ONT receives data at 1490nm and sends burst traffic
at 1310nm. Analogue video at 1550nm is received. Media
2. COMPONENTS OF GPON FTTH Access Controller (MAC) controls the upstream burst mode
traffic in an orderly manner and ensures that no collision
ACCESS NETWORK occur due to upstream data transmission from different homes
A passive optical network (PON) is a point-to-multipoint, [29]
shared optical fiber to the premises network architecture in
which unpowered optical splitters are used to enable a single They are fiber to copper media converters that offer RJ11,
optical fiber to serve multiple premises, typically 64–128. RJ45, and F-Series connectors to any device. These devices
passive optical networks are typically passive, in the sense are available in many configurations and port densities up to
that they employ a simple passive optical splitter and 24 ports. ONTs are available for outdoor and indoor use,
combiner for data transport. A PON takes advantage of provide POE or no POE, 10/100/1000, AES encryption, and
wavelength division multiplexing (WDM), using one can include batteries for survivability in the event of a power
wavelength for downstream traffic and another for upstream outage.
traffic on a single Non-zero dispersion-shifted fiber (ITU-T
GPON uses Dynamic Bandwidth Allocation that is it
G.652).
dynamically allocates the bandwidth depending on the
2.1 Optical Line Terminal OLT number of packets available in the T-CONT. Once the OLT
The Optical Line Terminal (OLT) is the main element of the reads the number of packets waiting in T-CONT it assigns the
network and it is usually placed in the Local Exchange and bandwidth. If there are no packets waiting in the T-CONT,
it’s the engine that drives FTTH system [29]. The most then OLT assigns the bandwidth to other T-CONT which
important functions that OLT perform are traffic scheduling, have packets waiting in T-CONT. If an ONT has a long queue
buffer control and bandwidth allocation [28]. OLTs typically OLT can assign multiple T-CONTS to that ONT [32].
operate using redundant DC power (-48VDC) and have at
least 1 Line card for incoming internet, 1 System Card for on-
3. GPON FTTH ACCESS NETWORK
board configuration, and 1 to many GPON cards. Each GPON ARCHITECTURE
card consists of a number of GPON ports. GPON’s have a tree topology in order to maximize their
coverage with minimum network splits, thus reducing optical
2.2 Optical Splitters power [3]. An FTTH access network comprises five areas,
The optical splitter splits the power of the signal. that is each namely a core network area, a central office area, a feeder
link (fiber) entering the splitter may be split into a given area, a distribution area and a user area as shown Figure 1. In
number of fibers leaving the splitter and there is usually three [10] the core network area is not considered as a part of the
or more levels of fibers corresponding to two or more levels FTTH access network. The network architecture adopted by
of splitters. This enables sharing of each fiber by many users. this paper is to use two level of splitting between the central
Due to power splitting the signal gets attenuated but its office and the user premises achieving an overall splitting
structure and properties remain the same. The passive optical ratio of 1:64. Level one splitter is 2:4 where the digit 2 comes
splitter need to have the following characteristics [29]: from type B protection to be explained in section 4. The
 broad operating wavelength range distance between the OLT and ONT may be more than 20 km
depending on the total available optical power budget, which
 low insertion loss and uniformity in any conditions is a factor of the OLT laser port and the total loss budget [29].
 minimal dimensions

31
 International Journal of Computer Applications (0975 – 8887)
Volume 92 – No.6, April 2014

Outside
Outside Plant
Plant OSP
OSP

Core
Core Network
Network Central
Central Office
Office Distribution
Distribution Customer
Customer
Feeder
Feeder Network
Network Network
Network Premises
Premises

ONT-
1
bllee
p CCaab
FDT-1 DDrroop
2:4 1:16
GPON LT(1)
FAT-1
FAT-1
Voice
Voice Core
Core ONT-
Network
Network 16
OLT

FDT-2 1:16
2:4
FAT-2
FAT-2
Data
Data Core
Core
Network
Network
GPON LT(M) 1:16
FDT-N
2:4 FAT-3
FAT-3
ONT-
49
1:16

Downstream: 1490 nm, 2.488 Gb/s FAT-4

FAT-4
ONT-
Upstream: 1310 nm, 1.244 Gb/s 64

Fig. 1 GPON FTTH access network architecture

3.1 FTTH Core Network 3.4 FTTH Distribution Network

The core network includes the internet service provider ISP Distribution cable connects level-1 splitter (inside the FDT)
equipments (typically BRAS and AAA server), PSTN (packet with level-2 splitter. Level-2 splitter is usually hosted in a
switched or the legacy circuit switched) and cable TV pole mounted box called Fiber Access Terminal FAT usually
provider equipment. placed at the entrance of the neighborhood. In the design
adopted by this paper level-2 splitter is 1:16, which means
3.2 Central Office each FAT serves 16 homes. The fiber cable running between
The main function of the central office is to host the OLT and level-1 splitter and level-2 splitter is called level-2 fiber [2].
ODF and provide the necessary powering. Sometimes it might
even include some (or all) of the components of the core 3.5 User Area
network. In the user area, drop cables, or level-3 fibers [2], are used to
connect the level-2 splitter inside the FAT to the subscriber
3.3 FTTH Feeder Network premises. Drop cables have less fiber count and length ranges
The feeder area extends from optical distribution frames up to 100 meters. Drop cables are designed with attributes
(ODF) in the central office CO to the distribution points. such as flexibility, less weight, smaller diameter, ease of fiber
These points, usually street cabinets, called Fiber Disruption access and termination. For ease of maintenance, usually an
Frames FDT where level-1 splitters usually reside. The feeder aerial drop cable is terminated at the entrance of the
cable is usually connected as ring topology starting from a subscriber home with a Terminal Box TB, then an indoor drop
GPON port and terminated into another GPON port as shown cable connects the TB to an Access Terminal Box ATB reside
in Fig.1 to provide type B protection. Level-1 splitters with a inside the home. Finally a patch cord connects the ONT to the
spilt ratio of 2:4 have been employed by our design. This ATB.
type of splitters enables the feeder to be connected to 2 GPON
ports from one side (for type B protection) and feeds a total of It is most important that the optical fibers are distributed in
4 distribution cables from the other side. The fiber cable such a way that efficient design, construction, maintenance
running between the CO and level-1 splitter is called Level-1 and operation for FTTH is achieved. Therefore, in order to
fiber [2] determine the network architecture, design, construction,
maintenance, and operation approach for the optical access
network, and to select optical components for FTTH,
telecommunication companies should mainly consider the
followings: [10]

32
 International Journal of Computer Applications (0975 – 8887)
Volume 92 – No.6, April 2014

- Scalability results in superposition of different ONT signals when it

reaches OLT. Hence TDMA [1] is adopted to avoid the
- Survivability interference of signals from ONTs. In TDMA time slots will
- Functionality be provided to each user on demand for transmission of their
packets. At the optical splitter packets arrive in order and they
- Construction and maintenance costs are combined and transmitted to OLT.
- Network upgradeability Type B protection [27], [34] is used in the design of the
- Operability and suitability over designed network lifetime. GPON FTTH access network presented in this paper. It
provides redundancy against both feeder and GPON port
4. TRAFFIC FLOW IN GPON FTTH failures. In this type of the protection, each fiber strand in the
feeder cable is connected to two GPON ports in the OLT as
ACCESS NETWORKS shown in Figure 1. One of the ports is configured as active
The data is transmitted from OLT to ONT in downstream as a
and the other as standby. Figure 2 shows the normal direction
broadcast manner and as a Time Division Multiplexing of traffic, once a failure in a fiber strand is happened, the
(TDM) in upstream [32].The wavelength of the downstream OLT automatically activates the standby GPON port to
data is 1490 nm, voice and data services from core network
broadcast a copy of the downstream traffic to feed the FDTs
transported over the optical network reaches the OLT and are
beyond the failure point from the other direction as shown in
distributed to the ONTs through the FTTH network by means Figure 3. This standby GPON port will also receive the
of power splitting. Each Home receives the packets intended upstream traffic of the isolated feeder portion. Figure 4
to it through its ONT. The upstream represents the data
depicts the situation when the active GPON port itself has a
transmission from the ONT to OLT. The wavelength is 1310
failure, in this case the OLT automatically divert the optical
nm. If the signals from the different ONTs arrive at the splitter signal to the protection line through the standby GPON port.
input at the same time and at the same wavelength 1310nm, it

FDT-1 FDT-1
2:4 2:4
GPON LT(1) GPON LT(1)
OLT
OLT

FDT-2 FDT-2
2:4 2:4
Link Failure

GPON LT(M) GPON LT(M)

FDT-N FDT-N
2:4 2:4

Fig. 2 Normal direction of traffic flow

Fig. 3 Type B protection in GPON FTTH access network,
the OLT send and receive traffic through the standby
GPON ports to overcome link failure

33
 International Journal of Computer Applications (0975 – 8887)
Volume 92 – No.6, April 2014

these locations to the network. Nearby locations are served

GPON Port by a common FAT while each of the diverse locations are
Failure FDT-1 served a by a dedicated FAT. Huawei MA5600T OLT
2:4 located at the CO is used as the access platform. This OLT
GPON LT(1) supports a 16 slots of 8-port GPON cards. Two level of
splitting is used to provide a total splitting ratio of 64. Level-1
splitters are 2-4 while level-2 splitters are 1:16. This means
OLT

FDT-2 that each GPON port can serve a total of 64 users. A bottom-
2:4 top approach is used to determine the required number of
GPON ports. By simple math, we can see that 16 GPON ports
with 64 split ratio are quite enough to serve 1000 users. This
GPON LT(M) statement is true for FTTH networks where the locations are
FDT-N geographically located close to each other and the number of
2:4 users distributed evenly among locations, which is not our
case. Due to the constraints of our network, the number of
required ports will be calculated depending on the number of
FATs. According to the 64 splitting ratio, each GPON port
can serve a total of 4 FATs as each FAT contain 1:16 splitter,
then 48 GPON ports are required to serve the 185 FATs.
Another bunch of redundant 48 GPON ports is used to
provide type-B protection. The total number of OLT GPON
cards used by the design will be 12, with 6 cards in each
Fig. 4 Type B protection in GPON FTTH access network, direction. 6 FDTs are used to hold level-1 splitters with each
the OLT sends and receives traffic through the standby FDT hold 8 splitters. As a result each FDT will be connected
GPON ports to overcome GPON-port failure to one OLT card using 8 Fibers from one direction and to the
backup card using 8 fibers from the other direction as shown
5. DESIGN OF THE GPON FTTH in Figure 6. Two feeder rings are used, the first feeder
consists 12 fibers among which 8 are connected to the 8 level-
ACCESS NETWORK 1 splitters inside FDT-3. The second feeder forms the second
The Design of an FTTH access network is challenging one; it ring connecting the other 5 FDTs. The extra 4 and 32 fibers,
needs to compromise different factors including size, cost, and in the first and second feeders respectively, are reserved for
scalability. There is no standard FTTH access network model future expansion or maintenance.
as the viability of access networks strongly depends on the Figures 7 and 8 show the distribution network connected to
subscriber density (subscribers per km2) and on settlement FDT-3 and FDT-4 respectively, due to space limitation the
structures, thus the modeling has to rely upon a concrete other distribution networks will not be presented, however the
settlement structure, a given country, and the results derived design procedure discussed above is followed in the design of
depend on that country [18]. all distribution networks of the project . The legend presented
To design the Outside Plant OSP, Desk top planning does not in Figure 7 applies equally in Figure 8. Three distribution
work, each root is surveyed physically and then planned fiber cables connected to FDT-3, namely 3/1, 3/2, and 3/3.
accordingly using knowledge and experience. International The circles in the figures refer to splicing closures. The
standards cannot be applied as each country has its own number inside the circle refers to the FDT/closure numbers,
unique underground factors. Ground thermal line or freeze for example, 4/1 refers to the first closure in FDT-4. The
line should be considered to identify the point in the FATs are presented as ellipses in the design, the number
underground where the temperature of the surrounding soil inside each ellipse indicates the FAT address. The
remains constant (not freezing nor overheating) thus allowing terminology adopted with FATs is to use 4 digit numbering.
for a constant temperature for the FO cable to lay in. Another The first digit from the left refers to the FDT code, the second
important factor that should be addressed is to decide the digit refers to the distribution cable sequence number and the
depth and the type of the backfill material necessary to reduce last two digits refer to the sequence number of the fiber strand
the ground vibration effects. used to connect that FAT. This terminology applies equally to
distribution networks connected all other FDTs. For example,
in Figure 5, FAT number 4121 is an FAT in the first
Figure (5) summarizes the sequence of steps involved in the
distribution cable of FDT-4, and connected to the 21th fiber
design of the FTTH access network in discussion. In reference
strand of that distribution cable. This terminology makes the
to Figure 1, the design starts with the customer premises,
design, implementation management, reporting and future
moving backward until reaching the central office in a
expansion easier. Two symbols are used for the FATs, the
bottom-up approach. The network particularly considered in
semicircle refers to FAT which only hold level-2 splitter,
this paper is required to provide service (voice and data) to a
while the semicircle over a triangle refers to an FAT which
total of 1000 users in 238 locations. According to the
holds level-2 splitter and provide splicing-closure function as
geographical separation of these locations and the number of
well. The lines refer to FO cables paths. The length of each
users per individual location, 185 FATs are used to connect
path, in

34
 International Journal of Computer Applications (0975 – 8887)
Volume 92 – No.6, April 2014

Site Survey

FDT-3

FDT-6
Mapping 12-FO
of OLT
locations
into GIS 72-FO
map

FDT-2
Out Side Plant
OSP Design
(feeder and
distrbution) FDT-5

Optical power FDT-1

budget
calculation

FDT-4

Is the design No Fig. 6 The feeder part of the GPON FTTH access network
valid ?
meters, is shown in the figures. The black lines represent
Yes trench paths, the red lines indicate areal paths, and the green
lines refer to situations where electrical poles are used to carry
distribution cables.
Determination of
Active
Determination of
the requird civil
Determination of
passive
6. DESIGN VALIDATION
components work components In order to assess the feasibility of the proposed design of the
(number of (FDTs, FATs, FTTH network and that each user in the network can receive
GPON ports and spliters, closures, adequate power , the total optical power loss between the
ONTS) FO cable length)
GPON port of the OLT and that of the ONT should be
considered. This loss can be summarized by the following
Total Cost
equation:
Calculation
𝑙𝑜𝑠𝑠 = 𝑙𝑐𝑎𝑏𝑙𝑒 + 𝑙𝑠𝑝𝑙𝑖𝑡𝑡𝑒𝑟 + 𝑙𝑠𝑝𝑙𝑖𝑐𝑒 + 𝑙𝑐𝑜𝑛𝑛𝑒 𝑐𝑡𝑜𝑟 (1)

Table (2) presents the definition and value of each parameter

in equation 1.
The power received by the ONT at the receiver premises is:
Is the
No implementation cost
Power received = Power transmitted- loss (2)
within the project
budget Where the power transmitted stands for the power emitted by
the GPON interface in the OLT card which is 3 dB in this
system. Table 2 shows the different values of losses, and the
Yes corresponding power received by individual ONTs. These
losses are calculated according to the parameters presented in
table (2). The locations considered in table (2) are chosen
Design approval because they are the most remote in network; therefore
represent the worst case power loss of the designed network.
The calculations presented in this table show that the worst
Fig. 5 GPON FTTH access network design steps case received power is well above the -26 dB ONT sensitivity.

35
 International Journal of Computer Applications (0975 – 8887)
Volume 92 – No.6, April 2014

Table 2. Parameters contributing to the optical power loss in GPON FTTH access networks
Parameter Description Value
𝑙𝑐𝑎𝑏𝑙𝑒 Account for the loss in optical signal power as it traverse the fiber cable, it is 0.21 dB/km
measured in dB/km. OTDR is used to measure the exact value of this parameter.
𝑙𝑠𝑝𝑙𝑖𝑡𝑡𝑒𝑟 Refers to splitter insertion loss, it varies according to the splitting ratio. The 8 dB for level-1 splitter.
values of used for this parameter are obtained from datasheets of the 14 dB for level-2 splitter
corresponding splitter.
𝑙𝑠𝑝𝑙𝑖𝑐𝑒 Represent the loss introduced due to splicing; it is measured by the fusion splice 0.003 dB
machine. The value shown represent the maximum loss obtained
𝑙𝑐𝑜𝑛𝑛𝑒𝑐𝑡𝑜𝑟 Manifests the loss introduced by connectors coupling. 0.2 dB

3312
3309
3314

297
1-FO
05
1-FO 33

3308
3311
1033

3/8
1-FO
540

33
04
233 3307

1-
32
O

FO
2-F

4
180

150
1-FO 3310

114
3313

830
3/11 O 3/7
4-F

0
86
3315 1-FO

1-
FO
0
135 3/6 76
2-FO

400
1-FO

2-FO

20
40

7-FO
2-FO
1-FO

03
06
33

33
866 1154
3316

3/12 3/10 3/9 3/5

14
1-FO 2-FO 4-FO 7-FO

-F
36

O
1
7855 O 3/4
1 -F

3302
271

FO
2-

1215
Legend 3317

3301

18-FO
3318

FDT

3/3
2020
Closure 3/1

3101
1-FO
FDT-3
4116 FAT 20

13-FO
3/2
4117

150
FAT (Join)
1-FO

3201
3/1
Trench Path 123

12-FO
165
960 360
Poles Path
5-FO 2-FO

3203
3/2

Electricity Path
5-FO
3204

3209 3202
71
3211
3213

3205

1-FO 2-FO
3/3
380

2820
3206
1-FO
97

3210
240
3212
3027

3208

Fig. 7 The distribution network connected to FDT-3

7. IMPLEMENTATION project with their sequence. Special consideration is given to

An engineering project should be implemented according to a FO testing at the end of each step. Two methods are adopted
pre-defined sequence of steps. This is especially crucial to in this project to determine the exact location of broken
projects which involve a mixer of engineering activities, optical fiber in an installed optical fiber cable when the cable
where an error in a certain stage might lead to a propagation jacket is not visibly damaged. These are OTDR testing and
of error in the subsequent stages. FTTH projects are amongst laser source/power meter set. Optical Time Domain
such projects where they involve a mixer of civil and Reflectometer OTDR is used for attenuation monitoring and
technical works. Project implementation planning saves time, fault location in the feeder network while laser source/power
efforts and cost. Therefore, a careful consideration is given to meter is used for the other tests. Figures 10-19 show photos
this issue. Figure 8 shows the major steps implemented in this of the steps charted in figure 9.

36
 International Journal of Computer Applications (0975 – 8887)
Volume 92 – No.6, April 2014

255
4201

4/2
90 6-FO
4/3

4202
1-FO

4203
FDT-4
4301
24-FO
4/1

4102 4124

655
4101

545

4204

568
110
4103

4120 4119

1-FO
4205

100 4122 4121

4/8
4104

4206
20-FO

4123

84
3-FO
1-FO 1-FO

684
4105
4106
490

4/1 811 426

57

4118
18-FO

4108
4107

220 13
4/7
41 6-FO 1-FO
300
4109

1-F
O

11

4117
12-FO
38

4/2 4/3
355

2-FO
1-FO

11
4111

561

-FO
4110

1366
4/4
4112 8-FO

602
3-F
O

14
41
16
25

1-F
O

4/5
18
57
2-F
O

50
4/6

O
1-F

1-F
15

O
41

16
41

Fig. 8 The distribution network connected to FDT-4

37
 International Journal of Computer Applications (0975 – 8887)
Volume 92 – No.6, April 2014

Table 3. Calculations of the optical power budget to validated the design

FDT-FAT OLT-FDT FAT-OLT connector closure-
# of FO loss splicing # of Received
FAT Code Distance Distance Distance coupling splicing
locations (dB) loss (db) closures Power (dB)
(meter) (meter) (meter) loss (dB) loss (dB)
3306 1 3476 1547 5023 1.055 1 0.12 4 0.012 -21.187
3316 1 9431 1547 10978 2.305 1 0.12 5 0.015 -22.440
3318 1 3235 1547 4782 1.004 1 0.12 1 0.003 -21.127
6407 1 1645 5057 6702 1.407 1 0.12 1 0.003 -21.530
6410 1 6002 5057 11059 2.322 1 0.12 2 0.006 -22.448
6413 1 9549 5057 14606 3.067 1 0.12 3 0.009 -23.196
3101 2 20 1547 1567 0.329 1 0.12 0 0 -20.449
3208 1 695 1547 2242 0.471 1 0.12 2 0.006 -20.597
3213 1 4095 1547 5642 1.185 1 0.12 3 0.009 -21.314
1101 2 2963 1616 4579 0.962 1 0.12 1 0.003 -21.085
1103 1 2880 1616 4496 0.944 1 0.12 3 0.009 -21.073
1105 1 4489 1616 6105 1.282 1 0.12 3 0.009 -21.411
1206 2 2165 1616 3781 0.794 1 0.12 1 0.003 -20.917
1217 1 4867 1616 6483 1.361 1 0.12 4 0.012 -21.493
1219 5 3432 1616 5048 1.060 1 0.12 2 0.006 -21.186
1226 1 5579 1616 7195 1.511 1 0.12 3 0.009 -21.640
6109 2 2215 5057 7272 1.527 1 0.12 4 0.012 -21.659
5102 1 150 2922 3072 0.645 1 0.12 0 0 -20.765
5208 2 470 2922 3392 0.712 1 0.12 0 0 -20.832
5318 2 2199 2922 5121 1.075 1 0.12 8 0.024 -21.219
4112 1 2216 2872 5088 1.068 1 0.12 2 0.006 -21.194
4116 1 6877 2872 9749 2.047 1 0.12 6 0.018 -22.185
4123 1 6156 2872 9028 1.896 1 0.12 6 0.018 -22.034
4206 1 910 2872 3782 0.794 1 0.12 0 0 -20.914

8. CONCLUSIONS
This paper presented a detailed design and implementation of
a type B protected GPON based FTTH access network In order to assess the validity of the design, the optical power
serving 1000 users, it adopted engineering approach to budgets is calculated for remote locations, and the results
emphasize practical aspects and field experience. The design showed that the highest power loss was -23.196 dB which is
procedure followed a bottom top approach, in which the size well below the upper limit. The implementation steps and
of the network and its components is defined after analyzing testing procedures are discussed, these steps are summarized
the requirements, the number of locations, the geographical in an implementation chart. The adoption of the procedure
separation and the available infrastructure. OSP design presented in this paper has saved a lot of efforts, cost and it
should be based on the physical survey of each root, desk top has speeded up project commission.
design causes wasting of a lot of time and cost when some
roots needs to be redesigned to fit with the physical
environments or to avoid certain obstacle.

38
 International Journal of Computer Applications (0975 – 8887)
Volume 92 – No.6, April 2014

Laser source/power meter

Approved Design
testing between level-1 splitter
and corresponding level-2
splitter

Civil work
1-Treanching
2- Poles Deployment Yes
Fault? Fault location

FDTs No
Deployment

TBs and ATBs

Deployment
FO cable
blowing

Outdoor drop cables

deployment and
ODF splicing splicing to
corresponding TBs

Laser source/power meter

OTDR test testing between level-2 splitter
and corresponding TB

Yes Yes
Fault? Fault location Fault? Fault location

No
No
Indoor drop cables
FDT splicing deployment and
(level-1 sipltter) splicing between TB
and ATB

Laser source/power meter

testing between ODF terminal Laser source/power meter
and coresponding level-1 siplter testing between TB and ATB

Yes Yes
Fault? Fault location Fault? Fault location

No

FATs ATB-to-ONT
Deployment batchcording

FAT splicing ONT-OLT

(level-2 sipltter) connectivity test

Fig. 9 Implementation steps of the GPON FTTH access network

39
 International Journal of Computer Applications (0975 – 8887)
Volume 92 – No.6, April 2014

PVC pipe

HDPE duct

Fig. 10 the OLT Fig. 11 The CO room showing Fig. 12 Trenching

the OLTs rack and the ODF

Fig. 15 Splicing process

Fig. 13 Level-1 splitter inside the FDT Fig. 14 FDT splicing brackets

Fig. 17 Laser source/power meter testing

Fig. 16 OTDR testing screenshot

40
 International Journal of Computer Applications (0975 – 8887)
Volume 92 – No.6, April 2014

Fig. 18 level-2 splitter inside the FAT Fig. 19 Pole mounted FAT

REFERENCES [9] Rajneesh Kalera and R.S. Kalerb, “Simulation of Fiber

[1] Stephan Smith, “Business class services over a GPON to the Home at 10 Gbit/s using GE-PON architecture,”
network,” in proc. IEEE Optical Fiber Communication Optik: Elsevier B.V, pp. 1362-1366, 2011.
Conference, 2006 and the 2006 National Fiber Optic [10] Bogyum KIM , Wonhyung LEE and Jinwoo HAN,
Engineers Conference. OFC 2006. “Outside Plant Architecture of Fiber-based Access
[2] M. Chardy et al., “Optimizing splitter and fiber location Network,” Digest of the 9th international conference on
in multilevel optical FTTH network,” European Journal optical Internet (COIN 2010).
of Operational Research: Elsevier B.V, pp. 430-440, [11] Edoardo Bonetto, Marco Mellia, and Michela Meo,
May 2012 “Energy Profiling of ISP Points of Presence,” in proc.
[3] Deeksha Kocher et al., “Simulation of fiber to the home IEEE ICC'12 Workshop on Green Communications and
triple play services at 2 Gbit/s using GE-PON Networking, pp. 5973-5977, 2012.
architecture for 56 ONUs,” Optik: Elsevier B.V, pp. [12] Salah Al-Chalabi, “Optically Powered Telephone System
5007-5010, 2013 over Optical Fiber with High Service Availability and
[4] Deepak Malik et al., “ Quality of service in two-stages Low Risk of Investment in FTTH Infrastructure,” IEEE
epon for fiber-to- the-home,” International Journal of Communications Magazine, August 2012.
Soft Computing and Engineering (IJSCE), vol. 2, No. 2, [13] Christoph Lange and Andreas Gladisch, “On the Energy
pp.387-390, May 2012. Consumption of FTTH Access Networks,” IEEE,
[5] Mohd Syuhaimi Ab-Rahman et. al, “New optical splitter [14] Andreas Gladisch , Christoph Lange and Ralph Leppla,
design for application in fibre-to-the home passive “Power efficiency of optical versus electronic access
optical network using virtual lab platform,” Journal of networks,” in proc. ECOC 2008, 21-25 September 2008,
Computer Science: Science Publications, pp. 846-871, Brussels, Belgium, pp. 1-4.
2012.
[15] Juan Rendon Schneir and Yupeng Xiong, “Economic
[6] James O. “High speed data to the home - an update,” in implications of a co-investment scheme for FTTH/PON
proc. 2011 IEEE International Conference on Consumer architectures,” Telecommunications Policy: Elsevier
Electronics (ICCE), pp. 663-664, 2011. B.V, pp. 849-860. 2013.
[7] M. S. Rahman et al., “Ideal and non ideal condition [16] Stephan Jay, Karl-Heinz Neumann n and Thomas
analysis based on protection scheme in distributed fiber Plückebaum, “Comparing FTTH access networks based
for immediate split Ftth-pon,” Journal of Applied on P2P and PMP fibre topologies,” Telecommunications
Science: Asian Network for Scientific Information, pp. Policy: Elsevier B.V, 2013,
1026-1032, 2011 http://dx.doi.org/10.1016/j.telpol.2013.04.010i.
[8] Duo Peng and Peng Zhang, “Design of Optical [17] Zijad Havic and Branko Mikac, “Software tool for
Integrated Access Network Based on EPON,” in proc. assessment of FTTH access networks,” in proc. 12th
2011 International Conference on Electronics and International Conference on Telecommunications -
Optoelectronics (ICEOE 2011), pp. 65-68, 2011 ConTEL 2013, pp. 47-52, June 2013.

41
 International Journal of Computer Applications (0975 – 8887)
Volume 92 – No.6, April 2014

[18] Steffen Hoernig et al., “The impact of different fiber [26] Rong Zhao et al., “Dynamic Migration Planning towards
access network technologies on cost, competition and FTTH,” in proc. IEEE 2010 9th Conference of
welfare,” Telecommunications Policy: Elsevier B.V, Telecommunication, Media and Internet, pp.1-6, 2010.
2012, pp. 96-112.
[27] Boyer Heard, “Availability and cost estimation of
[19] Marco Araújo and A. Manuel de Oliveira Duarte, “A secured FTTH architectures,” in proc. IEEE 2008
comparative study on cost-benefit analysis of fiber-to- International Conference on Optical Network Design
the-home telecommunications systems in Europe,” in and Modeling, pp.1-6.
proc. IEEE 2011 Baltic Congress on Future Internet and
Communications, pp. 65-69. [28] Yinghui Qiu, “Availability estimation of FTTH
architectures based on GPON,” in proc. IEEE 2011 7th
[20] Marco Forzati et al., “The uncaptured value of FTTH International Conference on Wireless Communications,
networks,” ,” in proc. IEEE 2011 13th International Networking and Mobile Computing, pp. 1-4.
Conference on Transparent Optical Networks ICTON-
2011, pp. 1-4. [29] Jani Saheb Shaik, “FTTH deployment options for
telecom operators,” www.sterlitetechnologies.com.
[21] Dirk Breuer et al., “Opportunities for Next-Generation
Optical Access,” IEEE Communications Magazine, [30] Frank Effenberger et al., “An Introduction to PON
February 2011. Technologies,” IEEE Communications Magazine,
March 2007, pp. 517-525.
[22] Sotiria Chatzi and Ioannis Tomkos, “ Techno-economic
study of high–splitting ratio PONs and comparison with [31] Cláudio Rodrigues et al., “Evolution of FTTH Networks
conventional FTTH-PONs/FTTH-P2P/ FTTB and FTTC Based on Radio-Over-Fibre,” in proc. IEEE 2011 13th
deployments,” in proc. IEEE 2011 Optical Fiber International Conference on Transparent Optical
Communication Conference and Exposition and the Networks ICTON, pp. 1-4
National Fiber Optic Engineers Conference, pp.1-3. [32] Satyanarayana Katlay and Abhinov Balagoni,
[23] Sofie Verbrugge et al., “Research Approach towards the “Technological and Cost based Analysis of Future-Proof
Profitability of Future FTTH Business Models,” in proc. Fiber Access Passive Networks: GPON and WDM
2011 Future Network & Mobile Summit, pp. 1-10, 2011. PON,” arXiv, pp. 1-4, 2013.

[24] Zijad Havic, “Economic Model Computing for FTTH [33] Jagjit Singh Malhotra, Manoj Kumar and Ajay K.
Access Network,” in proc. IEEE 5th International Sharma, “Low cost solution to high capacity 32 × 32
Conference on Pervasive Computing and Applications, channel FTTH duplex link employing triple play
pp. 218-222, 2010. services,” Optik: Elsevier B.V, pp. 93-96, 2014.

[25] Bruno Van Den Bossche et al., “ Maximizing the return [34] Josep Prat, Ed., Next-Generation Passive Optical
on investment for FTTX-rollout through the use of GIS Networks: Research Twords Unlimited Bandwidth
street maps and geomarketing data,” in proc. IEEE 2010 Access, Springer, 2008.
9th Conference of Telecommunication, Media and
Internet, pp.1-6, 2010.

IJCATM : www.ijcaonline.org 42

View publication stats