2.

Rust and acid-resistant fasteners

2.1 Mechanical properties Example:
DIN EN ISO 3506 applies to screws and nuts made A2–70
of stainless steel. There are a great number of stainless A Austenite steel
steels, which are classified in the three steel groups 2 Alloy type in group A
austenite, ferrite and martensite, whereby austenite steel is 70 Tensile strength not less than 700 MPa,
the most widespread. strain-hardened

The steel groups and the strength classes are designated

with a four-character sequence of letters and digits.

Steel group Austenite Martensitisch Ferrite

Steel grade A1 A221 A3 A423 A5 C1 C4 C3 F1

Strength classes
screws, nuts
type 1 50 70 80 50 70 110 50 70 80 45 60

Lower nuts 025 035 040 025 035 055 025 035 040 020 030

Soft Cold- High- Soft Hardened Soft Hardened Hardened Soft Cold-
formed strength and and and formed
tempered tempered tempered

Differentiation characteristics of austenite steel grades (in accordance with ISO 3506)

Steel group Chemical composition in % (maximum values, unless other details provided)
C Si Mn P S Cr Mo Ni Cu
A1 0.12 1 6.5 0.2 0.15–0.35 16–19 0.7 5–10 1.75–2.25
A2 0.1 1 2 0.05 0.03 15–20 – 8–19 4
A3 0.08 1 2 0.045 0.03 17–19 – 9–12 1
A4 0.08 1 2 0.045 0.03 16–18.5 2–3 10–15 4
A5 0.08 1 2 0.045 0.03 16–18.5 2–3 10.5–14 1
A3 and A5 stabilised against intercrystalline corrosion through adding titanium, niobium or tantalum.

Chemical composition of austenite steels (in accordance with ISO 3506)

10
1758
The most important stainless steels and their composition

Material name Material C Si Mn Cr Mo Ni Altri

no. % ≤% ≤% % % % %
A1 X 8 Cr Ni S 18-9 1.4305 ≤ 0.10 1.0 2.0 17.0 ÷ 19.0 – 8 ÷ 10 S 0.15 ÷ 0.35
A2 X 5 Cr Ni 1810 1.4301 ≤ 0.07 1.0 2.0 17.0 ÷ 20.0 – 8.5 ÷ 10 –
X 2 Cr Ni 1811 1.4306 ≤ 0.03 1.0 2.0 17.0 ÷ 20.0 – 10 ÷ 12.5 –
X 8 Cr Ni Ti 19/10 1.4303 ≤ 0.07 1.0 2.0 17.0 ÷ 20.0 – 10.5 ÷ 12 –
A3 X 6 Cr Ni Ti 1811 1.4541 ≤ 0.10 1.0 2.0 17.0 ÷ 19.0 – 9.0 ÷ 11.5 Ti ≥ 5 X % C
A4 X 5 Cr Ni Mo 1712 1.4401 ≤ 0.07 1.0 2.0 16.5 ÷ 18.5 2.0 ÷ 2.5 10.5 ÷ 13.5 –
X 2 Cr Ni Mo 1712 1.4404 ≤ 0.03 1.0 2.0 16.5 ÷ 18.5 2.0 ÷ 2.5 11 ÷ 14 –
A5 X 6 Cr Ni Mo Ti 1712 1.4571 ≤ 0.10 1.0 2.0 16.5 ÷ 18.5 2.0 ÷ 2.5 10.5 ÷ 13.5 Ti ≥ 5 X % C

Tab. 15: Common stainless steels and their chemical composition

Steel grade A1 Steel grade A5

Steel grade A1 is intended in particular for metal-cutting. Grade A5 steels are stabilised “acid-resistant steels” with
Because of the high sulphur content, steels of this grade properties of grade A4 steels (see A3 as well).
have lower corrosion resistance than corresponding steels
with a normal sulphur content. 2.1.1 Strength classification of stainless steel
screws
Steel grade A2 DIN EN ISO 3506 puts together the steel grades that are
Grade A2 steels are the more commonly used stain- recommended for fasteners. Austenitic steels in grade A2
less steels. They are used for kitchen equipment and for are used primarily. In contrast, in case of increased corro-
­apparatus for the chemical industry. Steels of this steel sion loads chromium-nickel steels from steel grade A4 are
grade are not suitable for use in non-oxidising acids and used. The mechanical strength values in Table 17 below
media containing chloride, e.g. in swimming pools and in are to be used for the construction of screw assemblies
sea water. made of austenitic steel.

Steel grade A3
Grade A3 steels are stainless steels stabilised through the
addition of titanium, possibly niobium, tantalum, with the
properties of A2 steels (stabilised against intercrystalline
corrosion, e.g. after welding).

Steel grade A4
Grade A4 steels are “acid-resistant steels” that are
­molybdenum alloyed and have much better corrosion
resistance. A4 steels are used in large volumes in the
­cellulose industry, because this steel grade was devel-
oped for boiling sulphuric acids (which is the reason for
the designation “acid-resistant”), and are suitable to a
certain extent for environments containing chloride. A4
steels are also used frequently in the food industry and in
ship building.

10
1759
 Mechanical properties of screws in the austenitic steel groups

Steel group Steel grade Strength Diameter Screws

class range
Tensile strength 0.2% offset Elongation
Rm1) yield point at fracture A2)
MPamin. Rp 0.21) mm min.
MPa min.
Austenitic A1, A2, A3, A4 50 ≤ M39 500 210 0.6 d
and A5 70 < M243) 700 450 0.4 d
80 < M243) 800 600 0.3 d
1)
The tensile stress is calculated in relation to the tension cross-section (see annex A or DIN EN ISO 3506-1).
2)
According to 6.2.4, the elongation at fracture is to be determined at the respective length of the screw and not on turned off specimens. d is the nominal diameter.
3)
In case of fasteners with a nominal thread diameter d > 24 mm the mechanical properties must be agreed between the user and the manufacturer. They must be marked with the
steel grade and strength class in accordance with this table.

Tab. 16: Extract from DIN EN ISO 3506-1

The yield point Rp0.2 is determined in accordance with 2.1.3 Reference values for tightening torques
DIN EN ISO 3506-1 in the tensile test of whole screws for screws, cf. chapter 6.6
because the strength properties are achieved in part
through cold forming. 2.2 Corrosion resistance of A2 and A4
Stainless steels and acid-resistant steels such as A2 and
2.1.2 Apparent yielding point loads for set A4 come in the category of “active” corrosion protection.
screws
Austenitic chromium-nickel steels cannot be hardened. A Stainless steels contain at least 16% chromium (Cr)
higher yield point can only be achieved through strain and are resistant to aggressive oxidising media. Higher
hardening that arises as a consequence of cold forming Cr contents and additional alloy components, such as
(e.g. round die thread rolling). Table 17 shows apparent nickel (Ni), molybdenum (Mo), titanium (Ti) or niobium
yielding point loads for set screws in accordance with (Nb), improve the corrosion resistance. These additives
DIN EN ISO 3506. also influence the mechanical properties. Other alloy
components are added only to improve the mechanical
Nominal Apparent yielding point loads properties, e.g. nitrogen (N), or the machining capability,
­diameter for austenitic steels in accordance
with DIN EN ISO 3506 A2 and e.g. sulphur (S).
A4 in N
Strength class 50 70 Fasteners made of austenitic steels are generally not
M5    2,980    6,390
magnetisable, but a certain amount of magnetisability
M6    4,220    9,045
may be present after the cold forming. However, this does
M8    7,685   16,470
not affect the corrosion resistance. Magnetisation through
M10   12,180   26,100
strain hardening can go so far that the steel part sticks to
M12   17,700   37,935
a magnet.
M16   32,970   70,650
M20   51,450 110,250
Under the effect of oxygen stainless steel forms a stable
M24   74,130   88,250
oxide layer (passive layer). This passive layer protects the
M27   96,390 114,750
metal from corrosion.
M30 117,810 140,250

Tab. 17: Apparent yielding point loads for set screws in

accordance with DIN EN ISO 3506

10
1760
It should be noted that in practice there are a number of be the starting point for pitting. For this reason, residues
different types of corrosion. The more frequent types of and deposits must be cleaned regularly from all fasteners.
corrosion involving stainless steel are shown below and in
the following Fig. J as examples: Austenitic steels such as A2 and A4 are more resistant to
pitting than ferrite chromium steels.

Classification of the degree of resistance into

different groups

Degree of Assessment Weight loss in

resistance g/m2h
A Fully resistant < 0.1
B Practically resistant 0.1–1.0
C Less resistant 1.0–10
D Not resistant > 10

Tab. 22

2.2.3 Contact corrosion

a Surface degrading corrosion, pitting
Contact corrosion occurs when two components with
b Contact corrosion
­different compositions are in metallic contact with each
c Stress corrosion cracking
other and there is moisture in the form of an electrolyte.
d Mechanical effects
The baser element is attacked and destroyed.
Fig. K: The most frequent corrosion types with screw
The following points should be observed to prevent
­assemblies
contact corrosion:
• Insulating the metals at the contact point, e.g. through
2.2.1 Surface and degrading corrosion
rubber, plastics or coatings, so that a contact current
With uniform surface corrosion, also known as degrading
cannot flow.
corrosion, the surface is degraded evenly. This type of
• Where possible, avoid unequal material pairings.
corrosion can be prevented through a careful selection of
As an example, screws, nuts and washers should be
the material.
matched to the connecting components.
• Make sure that the connection is not in contact with
On the basis of laboratory experiments manufacturers
electrolytic active means.
have published resistance tables that provide information
→ cf. chapter 6.8 as well
on the behaviour of the steel grades at different tempera-
tures and concentrations in the individual media (see
2.2.4 Stress corrosion cracking
chapter 2.2.5).
This type of corrosion usually occurs in components used
in industrial atmospheres that are under heavy mechani-
2.2.2 Pitting
cal tensile and bending loads. Internal stresses created by
Pitting is seen through surface corrosion degrading with
welding can also lead to stress corrosion cracking.
the additional formation of cavities and holes. The passive
layer is penetrated locally here.
Austenite steels in atmospheres containing chloride are
particularly sensitive to stress corrosion cracking. The influ-
In case of stainless steel in contact with active media
ence of the temperature is considerable here. The critical
­containing chloride there is also pitting by itself with
temperature is 50°C.
pinhole notches in the material. Deposits and rust can also

10
1761
 2.2.5 A2 and A4 in combination with corrosive
media
The following table provides an overview of the resist-
ance of A2 and A4 in combination with various corrosive
media. The values shown are intended only as reference
points but still provide good possibilities for comparisons.

Overview of the chemical resistance of A2 and A4 screws

Corrosive agent Concentration Temperature in °C Degree of resistance Degree of resistance

A2 A4
Acetic acid 10% 20 A A
boiling A A
Acetone all all A A
Ammoniac all 20 A A
boiling A A
Beer – all A A
Benzene, all types – all A A
Benzoic acid all all A A
Benzol – all A A
Blood – 20 A A
Bonderising solution – 98 A A
Carbon dioxide – – A A
Chloride: dry gas, – 20 A A
damp gas all D D
Chloroform all all A A
Chromic acid 20 A A
10% pure boiling C B
20 B B
50% pure boiling D D
Citric acid to 10% all A A
50% 20 A A
boiling C B
Copper acetate – all A A
Copper nitrate – – A A
Copper sulphate all all A A
Developer (photogr.) – 20 A A
Ethyl alcohol all 20 A A
Ethyl ether – all A A
Fatty acid technical 150 A A
180 B A
200–235 C A
Formic acid 10% 20 A A
boiling B A
Fruit juices – all A A
Glycerine conc. all A A
Hydrochloric acid 0.2% 20 B B
50 C B
2% 20 D D
50 D D
to 10% 20 D D
10
1762
Corrosive agent Concentration Temperature in °C Degree of resistance Degree of resistance
A2 A4
Hydrocyanic acid – 20 A A
Industrial air – – A A
Lactic acid all A A
1.5% 20 A A
10% boiling C A
Lemon juice – 20 A A
Magnesium sulphate approx. 26% all A A
Mercury – to 50 A A
Mercury nitrate – all A A
Methyl alcohol all all A A
Milk of lime – all A A
Nitric acid to 40% all A A
50% 20 A A
boiling B B
90% 20 A A
boiling C C
Oils – all A A
(mineral and vegetable)
Oxalic acid 10% 20 B A
boiling C C
50% boiling D C
Petroleum – all A A
Phenol pure boiling B A
Phosphoric acid 10% boiling A A
50% 20 A A
boiling C B
80% 20 B A
boiling D C
conc. 20 B A
boiling D D
Potassium permanganate 10% all A A
Salicylic acid – 20 A A
Seawater – 20 A A
Sodium carbonate cold saturated all A A
Sodium hydroxide 20% 20 A A
boiling B B
50% 120 C C
Sodium nitrate – all A A
Sodium perchlorate 10% all A A
Sugar solution – all A A
Sulphur dioxide – 100–500 C A
900 D C
Sulphuric acid. 1% to 70% B A
boiling B B
2.5% to 70 B A
boiling C C
5% 20 B A
> 70 B B
10% 20 C B
70 C C
60% all D D
Sulphurous acid aqueous solution 20 A A
Tannic acid all all A A
10
1763
 Corrosive agent Concentration Temperature in °C Degree of resistance Degree of resistance
A2 A4
Tar – hot A A
Tartaric acid to 10% 20 A A
boiling B A
over 100% 20 A A
to 50% boiling C C
75% boiling C C
Wine – 20 and hot A A

2.2.6 Creation of extraneous rust

Extraneous rust consists of adherent particles of a carbon
steel (“normal steel”) on the stainless steel surface that
turn into rust through the effect of oxygen. If these places
are not cleaned and removed, the rust can cause electro-
chemical pitting corrosion even in stainless steel.

Extraneous rust can be caused by:

• Contact of objects that rust with a stainless steel
surface.
• Flying sparks during work with a right angle grinder, or
grinding dust. or during welding work.
• Water containing rust dripping onto a stainless steel
surface.
• Use of tools that were previously used to work on
carbon steel.

10
1764
 Origin mark

XYZ
XYZ A2-70

A2-70
A2-70 XYZ

A4
Alternative marking
Steel group Strength class for socket head
cap screws

XYZ

A2-70

XYZ
Marking of screws that do not
satisfy the requirements for tensile
or torsion strength because of their
geometry, e.g. low cylinder heads

A2

Fig. L: Extract from DIN EN ISO 3506-1

2.3 Marking corrosion-resistant screws and Marking nuts in accordance with

nuts DIN EN ISO 3506-2
The marking of corrosion-resistant screws and nuts must Nuts with a nominal thread diameter from 5 mm must
contain the steel group, the strength class and the manu- be clearly marked in accordance with the classification
facturer’s mark. system. Marking on a single flat is permissible and may
only be recessed. Marking on the flats is also permissible
Marking screws in accordance with as an option.
DIN EN ISO 3506-1
Hexagon head screws and socket head cap screws from
nominal diameter M5 must be clearly marked in accord-
XYZ
ance with the classification system. Where possible, the
XYZ
marking should be on the screw head.

A2-50

Strength class only with

low-strength nuts
(see chapter 3.2.3)

Fig. M: Extract from DIN EN ISO 3506-2

10
1765