Optical Detectors

Wei-Chih Wang
Department of Power Mechanical Engineering
National Tsing Hua University

w.wang 1
 Week 12
• Course Website: http://courses.washington.edu/me557/optics
• Reading Materials:
- Week 12 reading materials are from:
http://courses.washington.edu/me557/readings/
• HW #2 due today
• Set up a schedule to do Lab 2
• Prism Design Project memo and presentation due Week 13
(next Monday)
• Final Project proposal: Due Monday Week 14
• Set up a time to meet with me to discuss your final project in
Week 14
• Final Project Presentation on 6/11 (Monday) 1:20-4:10 - PM
w.wang 2
 Last Week
• Light sources
- Chemistry 101, orbital model-> energy gap model (light in quantum), spectrum
in energy gap
- Broad band light sources ( Orbital energy model, quantum theory,
incandescent filament, gas discharge, LED)
- LED (diode, diode equation, energy gap equation, threshold voltage, device
efficiency, junction capacitance, emission pattern, RGB LED, OLED)
- Narrow band light source (laser, Coherence, lasing principle, population
inversion in different lasing medium- ion, molecular and atom gas laser, liquid,
solid and semiconductor lasers, laser resonating cavity- monochromatic light,
basic laser constitutive parameters)

w.wang 3
 This Week
• Photodetectors
- Photoemmissive Cells
- Semiconductor Photoelectric Transducer
(diode equation, energy gap equation, reviser bias
voltage, quantum efficiency, responsivity, junction
capacitance, detector angular response, temperature
effect, different detector operating mode, noises in
detectors, photoconductive, photovoltaic, photodiode,
PIN, APD, PDA, PSD, CCD, CMOS detectors)
- Thermal detectors (IR and THz detectors)

w.wang 4
 Types of Optical Detectors
Photon detectors are subdivided according to the physical effect that produces the detector response. We
will present some of the important classes of photon detectors as follow:

•Photoemissive. These detectors are based on the photoelectric effect, in which incident photons
release electrons from the surface of the detector material. The free electrons are then collected in an
external circuit.

•Photoconductive. The incoming light produces free electrons which can carry electrical current so
Semiconductor

that the electrical conductivity of the detector material changes as a function of the intensity of the
incident light. Photoconductive detectors are fabricated from semiconductor materials such as
silicon (e.g. photoconductive antenna).

•Photovoltaic. Such a detector contains a junction in a semiconductor material between a region

where the conductivity is due to electrons and a region where the conductivity is due to holes (a so-
called pn junction). A voltage is generated when optical energy strikes the device (e.g. solar cell).

• Photodiode: The current is generated when photons are absorbed in the photodiode. A small
amount of current is also produced when no light is present.

•Thermal detector or IR detector: A thermal detector absorbs radiation and changes temperature.
Because the power in absorbed radiation is typically rather small (<10-7 W), the detector itself
should be small so that it has a low heat capacity. There are several different kind of detection
techniques: thermoelectric, pyroelectric, bolometer, phnematic.
w.wang 5
 Different Photodetectors
1. Photoemmissive Cells
There are basically 2 Types of Photo- emmissive Cells and these are
- Vacuum Type Photocell
- Gas Filled Type
- Photomultipliers
2. Semiconductor Photoelectric Transducer
These include :
- Photoconductive Cells
- Photovoltaic Cell (solar cell)
- Phototransistors (photodiode, CCD, PIN etc.)
- Photothyristors
3. Thermal detectors (IR detector)
- Thermoelectric
- Bolometer
- Pneumatic
- Pyroelectric
- Photoconductive antenna
- GUN, TUNNET, RTD, IMPATT, MIC
w.wang 6
 Photoemission Detectors
Photoemission detectors are either evacuated or
gas-filled tubes containing a cathode and one or
more anodes. When photons impinge on the
cathode, the electrons are ejected from the cathode
surface and are accelerated toward the anode that is
at a positive potential with respect to the cathode.
The photoelectric current increases proportionally
to the intensity of the illumination. This design is
the simplest diode version of the detector. In order (a) Photoemissive cell (b) and photomultiplier. L
to increase the sensitivity, several more electrodes = light flux, Eo through E4 = differences in
(dynodes) are added to the construction of the potentials between cathode and one of electrodes,
detector. In this device, called a photomultiplier, the 1 and 2 = cathodes, 3 and 4 = anodes, 5, 6, and 7
electrons that are ejected from the cathode are = dynodes, 8 and 9 = glass envelopes.
focused on one of the dynodes. When the surface of
the dynode is struck, an increased number of
electrons are liberated.
The electrons flow to the next dynode, where the process is repeated with a progressively increasing
number of electrons. The dynodes have sequentially higher positive potentials with respect to each
other. As a result, the output current has a significantly increased magnitude, which defines the high
sensitivity of the detector.
w.wang 7
 Photomultiplier Tubes (PMTS)

Photomultiplier Tubes (PMTS) are light detectors that are useful in low
intensity applications such as fluorescence spectroscopy. Due to high
internal gain, PMTs are very sensitive detectors.
w.wang 8
 Photomultiplier Tubes

Secondary emission of electrons due to high velocity electrons

- Amplification is very high (10,000x possible) Mim Lal Nakarmi, KSU

- Used in single photon counter

w.wang 9
 Semiconductor
Variable conductivity
A pure semiconductor is a poor electrical conductor as a consequence of having just the right number of electrons to
completely fill its valence bonds. Through various techniques (e.g., doping or gating), the semiconductor can be
modified to have excess of electrons (becoming an n-type semiconductor) or a deficiency of electrons (becoming a p-
type semiconductor). In both cases, the semiconductor becomes much more conductive (the conductivity can be
increased by a factor of one million, or even more). Semiconductor devices exploit this effect to shape electrical current.
Junctions
When doped semiconductors are joined to metals, to different semiconductors, and to the same semiconductor with
different doping, the resulting junction often strips the electron excess or deficiency out from the semiconductor near the
junction. This depletion region is rectifying (only allowing current to flow in one direction), and used to further shape
electrical currents in semiconductor devices.
Energetic electrons travel far
Electrons can be excited across the energy band gap of a semiconductor by various means. These electrons can carry
their excess energy over distance scales of microns before dissipating their energy into heat, significantly longer than is
possible in metals. This effect is essential to the operation of bipolar junction transistors.
Light energy conversion
Electrons in a semiconductor can absorb light, and subsequently retain the energy from the light for a long enough time
to be useful for producing electrical work instead of heat. This principle is used in the photovoltaic cell (e.g. solar cell).
Conversely, in certain semiconductors, electrically excited electrons can relax by emitting light instead of producing heat.
This is used in the light emitting diode.
Thermal energy conversion
Semiconductors are good materials for thermoelectric coolers and thermoelectric generators, which convert temperature
differences into electrical power and vice versa. Peltier coolers use semiconductors for this reason.

w.wang 10
 Photoconductive
In these semiconductor based detectors light
whose energy is greater than that of the bandgap
causes the generation of electron-hole pairs. As
long as the electron remains in the conduction
band, the conductivity of the semiconductor will
be increased. This is the phenomenon of
photoconductivity, which is the basic mechanism
operative in photoconductive detectors.

The bulk effect photoconductors have no

junction. The bulk resistivity decreases with
increasing illumination, allowing more
photocurrent to flow. This resistive characteristic
gives bulk effect photoconductors a unique
quality: signal current from the detector can be
varied over a wide range by adjusting the applied
voltage. Geometry of a slab of
photoconductive material.
Photoconductor bias circuit: The slab of length L, width
changes in the resistance of the W and thickness D has
photoconductor cause changes electrodes on opposite
in the voltage appearing across faces; radiation falls onto
w.wang RL. the upper face.
11
 Photoconductive Cell
Photocells are high resistance thin
film devices made by depositing a
layer of a photoconductive material
on a ceramic substrate.

For a given type of photoconductor

material, at a given level of
illumination, the photoconductive
film will; have a certain sheet
resistivity. The resistance of the
photocell at this light level is
determined by the electrode
geometry:
w.wang 12
 Why Use Photocells?
• Lowest cost available in visible and near-IR photo detector
• Available in low cost plastic encapsulated packages as well as hermetic packages
(TO-46, TO-5, TO-8)
• Responsive to both very low light levels (moonlight) and to very high light levels
(direct sunlight)
• Wide dynamic range: resistance changes of several orders of magnitude between
"light" and "no light"
• Low noise distortion
• Maximum operating voltages of 50 to 400 volts are suitable for operation on 120/240 VAC
• Available in center tap dual cell configurations as well as specially selected
resistance ranges for special applications
• Easy to use in DC or AC circuits - they are a light variable resistor and hence symmetrical
with respect to AC waveforms
• Usable with almost any visible or near infrared light source such as LEDS; neon;
fluorescent, incandescent bulbs, lasers; flame sources; sunlight; etc
• Available in a wide range of resistance values

w.wang 13
 Applications
Photoconductive cells are used in many different types of circuits and applications.

Analog Applications
• Camera Exposure Control
• Auto Slide Focus - dual cell
• Photocopy Machines - density of toner
• Colorimetric Test Equipment
• Densitometer
• Electronic Scales - dual cell
• Automatic Gain Control - modulated light source
• Automated Rear View Mirror
Digital Applications
• Automatic Headlight Dimmer
• Night Light Control
• Oil Burner Flame Out
• Street Light Control
• Absence / Presence (beam breaker)
• Position Sensor

w.wang 14
 Semiconductor PN Junction types

P tyep
n tyep

P-N junction (no bias, short circuit)

1. Absorbed h excited e from valence to conduction,

resulting in the creation of e-h pair
2. Under the influence of a bias voltage these carriers move
through the material and induce a current in the external circuit.
3. For each electron-hole pair created, the result is an electron
flowing in the circuit.
w.wang 15
 Photovoltaic Cell
All photovoltaic (PV) cells consist of two or
more thin layers of semi-conducting material,
most commonly silicon (monocrystalline,
polycrystalline, amorphous, thick film) and
other materials such as cadmium telluride
(CdTe) and copper indium diselenide (CIS).

Thee semiconductor wafers are specially treated

to form an electric field, positive on one side
and negative on the other. When light energy
strikes these cells, electrons are knocked loose
from the atoms in the semiconductor material.
If electrical conductors are attached to the
positive and negative sides, forming an
electrical circuit, the electrons can be captured P tyep
n tyep
in the form of an electric current The electrical
output from a single cell is small, so multiple
cells are connected together to form a 'string',
which produces a direct current.
w.wang 16
 Multi-junction Cell
Today's most common PV devices use a single junction, or interface, to
create an electric field within a semiconductor such as a PV cell. In a
single-junction PV cell, only photons whose energy is equal to or greater
than the band gap of the cell material can free an electron for an electric
circuit.

One way to get around this limitation is to use two (or more) different
cells, with more than one band gap and more than one junction, to
generate a voltage. These are referred to as "multijunction" cells (also
called "cascade" or "tandem" cells). Multijunction devices can achieve a
higher total conversion efficiency because they can convert more of the
energy spectrum of light to electricity.

Much of today's research in multijunction cells focuses on gallium

arsenide as one (or all) of the component cells. Such cells have reached
efficiencies of around 35% under concentrated sunlight (compare to
15% monocrystal silicon). Other materials studied for multijunction
devices have been amorphous silicon and copper indium diselenide
(CIS). .
As shown below, a multijunction device is a stack of
individual single-junction cells in descending order of band
gap (Eg). The top cell captures the high-energy photons
and passes the rest of the photons on to be absorbed by
lower-band-gap cells.
w.wang 17
 Photovoltaic Cell
(Organic Solar Cell)
Organic thin-film solar cells using low-molecular-
weight materials are fabricated by vacuum
deposition. First, organic materials having p- and n-
type conductivities are successively deposited on a
transparent electrode, and then, a metal electrode is
deposited on them. The mechanism of electrical
power generation in OSCs can be understood as an
opposite process of emissions in OLEDs. Sunlight
is absorbed by organic layers in OSC, and excitons
generated by light absorption are dissociated to
electrons and holes at the interface between p- and
n-type organic layers. The electrons and holes are
collected at the upper and lower electrodes,
respectively, and electricity is generated.
Furthermore, it is known that power conversion
efficiency is improved by insertion of an electron
transport layer.

w.wang 18
 Solar cell
• Heterojunction to improve
coupling efficiency
• Multilayer for broadband
• Lenses, mirror arrays to
improve light collection

w.wang 19
 Photodiodes and Phototransistors
– Photodiodes are designed to detect photons and
can be used in circuits to sense light.
– Phototransistors are photodiodes with some
internal amplification.
Note:
Reverse current flows through the P tyep
n tyep
photodiode when it is sensing light.

If photons excite carriers in a reverse-

biased pn junction, a very small
current proportional to the light
intensity flows.

The sensitivity depends on the

wavelength of light.
w.wang 20
 i-v characteristic of a real diode
• Real diode is close to ideal

Ideal Diode

Threshold
or bias
 v D nV T  voltage
iD  I S  e  1 
w.wang
  21
 Photodiode Operation

A photodiode behaves as a
photocontrolled current source in parallel
with a semiconductor diode and is
governed by the standard diode equation

Ip = eP/(h)
where I is the total device current, I p is Two significant features to note from both
the photocurrent, Idk is the dark current the curve and the equation are that the
(leakage current), V0 is the voltage photogenerated current (Ip) is additive to
across the diode junction, q is the charge the diode current, and the dark current is
of an electron, k is Boltzmann's constant, merely the diode's reverse leakage
and T is the temperature in degrees current. Finally, the detector shunt
Kelvin. P= radiation energy, quantum resistance is the slope of the I-V curve
22
(dV/dI ) evaluated at V= 0.
w.wang coefficient
 Photodiode Light Sensitivity
The current through a photodiode
is directly proportional to the
intensity of the incident light.

Id~ Ip + Isat

w.wang 23
Three key features happening in reverse bias

p type

n type

- Reverse bias current is mainly due to minority carriers

- Photo current increases significantly in reverse bias
- diffusion current outside the depletion region diffusion is slow process
(high potential barrier)
w.wang 24
 Depletion Widen with Increase
Reverse Bias
The application of a reverse
voltage to the p-n junction minority carriers
will cause a transient
current to flow as both
electrons and holes are
pulled away from the
junction. When the potential
formed by the widened VA
depletion layer equals the Depletion region width:
applied voltage, the current
W = [2rVbi-VA)(NA+ND)/(q NAND)]1/2
will cease except for the
small thermal current.
25
w.wang  v D nV T 
iD  I S  e  1  ~ Isat because VD is negative
 
 Potential Barrier Increase with
Increase Reverse Bias

high potential barrier

W = [2rVbi-VA)(NA+ND)/(q NAND)]1/2
To reverse-bias the p-n junction, the p side is made more negative, making it "uphill" for
electrons moving across the junction. The conduction direction for electrons in the diagram is
right to left, and the upward direction represents increasing electron energy.

w.wang 26
Thermal Current Due to minority carriers

minority carriers
Drift across depletion
region due to reverse
voltage

w.wang 27
 Maximum Reverse Voltage (Vr)

Applying excessive
reverse voltage to
photodiodes may cause
breakdown and severe
degradation of device
performance. Any
reverse voltage applied
must be kept lower
than the maximum
rated vale, (Vr max).

w.wang 28
 Quantum efficiency
A photodiode's capability to convert light energy to electrical
energy, expressed as a percentage, is its Quantum Efficiency,
(Q.E.).
# of electrons (holes) collected as Ip/sec
re/rp = ---------------------------------------------------
# of incident photons/sec

Depends on , through absorption coefficient, thickness of layers,

Doping, geometry, etc. Operating under ideal conditions of
reflectance, crystal structure and internal resistance, a high quality
silicon photodiode of optimum design would be capable of
approaching a Q.E. of 80%.
w.wang 29
 Photodiode Responsivity
Responsivity R is defined as the ratio of radiant energy (in watts), P,
incident on the photodiode to the photocurrent output in amperes Ip. It is
expressed as the absolute responsivity in amps per watt. Please note that
radiant energy is usually expressed as watts/cm^2 and that photodiode
current as amps/cm^2. The cm^2 term cancels and we are left with
amps/watt (A/W).

Ip
R  (A/W)
P

Since h = energy of photon, P = rp h

where rp = photon flux = P/ h # photons/ sec

w.wang 30
 Recall QE is re/rp
Electron rate then
P = rp h

re = rp = P/(h)

Therefore, the output photo current Ip=ere is

Ip = eP/(h)
Ip
The responsivity R  may then be written
P
R = e/(h) = e/(hc) = (A/W)

h= plank constant = 6.63x10-34 joule-sec

w.wang 31
 Responsivity

R = 

w.wang 32
 Responsivity
R = 
Bias or no bias

R 

Silicone based
detector

A typical responsivity curve that shows A/W as a function of wavelength

w.wang 33
 Responsivity and Quantum Efficiency
R = 
re/rp Silicon ~ 90%
InGaAs ~ 70%
R
Silicon PN~ 0.41–0.7
Silicon PIN ~ 0.6–0.8
InGaAs PIN ~0.85
InGaAs APD ~0.8
Germanium ~0.7

w.wang 34
 Junction Capacitance
When designing a sensing circuit to maximize the
speed or linearity of response, one must know
two important electrical characteristics of a Cj = r W
photodiode: the junction capacitance and the
shunt resistance. Without these, the RC time
constant of the complete operating circuit cannot
be calculated.

The parallel plate capacitance across the

depletion region gives rise to a junction
capacitance (Cj) which increases with the area A
of the junction. Since increasing capacitance in a
circuit slows its speed of response, photodiodes
with smaller active areas are inherently capable
of faster response than those with larger active
areas. The junction capacitance is a function of
the thickness of the depletion layer W, which
varies with applied bias VA, as shown in the
graph. Therefore, it is common to specify the W = [2rVbi-VA)(NA+ND)/(q NAND)]1/2
junction capacitance at zero external bias.
w.wang 35
 Response Time
In many applications the most important
Rise time (tr)
parameter is dynamic performance. This is the measure of the photodiode response
speed to a stepped light input signal. It is the time
Photodiode response time is the root mean required for the photodiode to increase its output
square sum of the charge collection time and from 10% to 90% of final output level.

the RC time constant arising from series

plus load resistances and the junction and
stray capacitances. Charge collection time
is voltage dependent and is made up of a
fast and a slow component. The fast
component is the transit time of the charge
carriers (electrons and holes) through the
depletion region, producing carriers that are
collected by diffusion. The transit time of
these carriers will be relatively slow. The
figure below illustrates the transient
response of a photodiode to a square pulse
of radiation.
w.wang 36
 Response time
The time required for the detector to respond to an optical input.
The response time is related to the bandwidth of the detector by

BW = 0.35/tr Junction capcacitance

where tr is the rise time of the device. The rise time is the time it
takes for the detector to rise to a value equal to 63.2% of its final
steady-state reading.
1/RC
Cj = r W

W = [2rVbi-VA)(NA+ND)/(q NAND)]1/2

w.wang 37
Typical Photodetector Characteristics
Photodetector Wavelength Responsivity Dark Rise Time
(nm) (A/W) Current (nA) (ns)
Silicon PN 550–850 0.41–0.7 1–5 5–10

Silicon 850–950 0.6–0.8 10 0.070

PIN
InGaAs 1310–1550 0.85 0.5–1.0 0.005–5
PIN
InGaAs 1310–1550 0.80 30 0.100
APD
Germaniu 1000–1500 0.70 1000 1–2
m
w.wang 38
 Detector Angular Response
The photocurrent generated from a photodiode is essentially independent of angle of
incidence of the incoming radiation when the angle of incidence is less than 30
degrees. Typically, a variation in photocurrent of 1% to 2% can be expected,
provided the detector's active area is underfilled, (i.e., the incoming radiation does
not completely cover the device's entire active area). This condition assumes the
photodiode's absorption layer thickness approximately equals the depletion layer
thickness in the photodiode junction.

In circumstances where the photodiode is immersed in a collimated beam of incident

light, the device's responsivity will fall off with the cosine of the angle of incidence as
follows: 

where is the photodiode responsivity at normal incidence. Detection pattern

w.wang 39
 Temperature Effects

Typically, the dark current of a PNN+ silicon photodiode approximately

doubles for each 10°C increase or decrease in the device temperature.
The shunt resistance approximately doubles for each 6°C change:
.

These formulas can be used to calculate the shunt resistance and dark
current for any temperature from the specified values, which are usually
specified at 25°C.

w.wang 40
Increasing the temperature of a semiconductor shifts its absorption
spectrum to longer wavelengths by reducing the effective band gap.
Fortunately, the absorption spectrum of silicon is quite broad. Consequently,
the small temperature-induced shifts in the absorption spectrum only affect the
responsivity significantly at the edges of the spectral responsivity curve, as
shown in the figure below.

w.wang 41
 Temperature Effects

Increasing the operating temperature of a photodiode device results in two

distinct changes in operating characteristics. The first change is a shift in the
Quantum Efficiency (Q.E.) due to changes in the radiation absorption of the
device. Q.E. values shift lower in the UV region and higher in the IR region.
w.wang 42
 Equivalent Operating Circuits
A photodiode behaves as a photocontrolled current source in parallel
with a semiconductor diode

Vo

Vo

w.wang 43
Fundamentally a photodiode is a current generator. The junction capacitance of
the photodiode depends on the depletion layer depth and hence bias voltage.
The value of the shunt resistance Rd is usually high (megohms). The series
resistance Rs is low. The effect of the load resistor Rl value on the
current/voltage characteristics is shown in the following figure:

Cj = r W

W = [2rVbi-VA)(NA+ND)/(q NAND)]1/2

V
(a) Photovoltaic Operation - Rl>>Rd, load line, increase voltage like solar cell
(b) Zero Bias Operation - Rl<<Rd, load line, no bias bad way to connecting diode
(c) Photoconductive Operation - load line, best way current change with load
w.wang 44
 Photovoltaic
(a) Photovoltaic Operation - Rl>>Rd, load line

The generated photocurrent flows through Rd causing a voltage across the diode.
This voltage opposes the band gap potential of the photodiode junction, forward
biasing it. The value of Rd drops exponentially as the illumination increases.
Thus the photo-generated voltage is a logarithmic function of incident light
intensity. The major disadvantage of this circuit is that the signal depends on Td,
which typically has a wide spread of values over different production batches.
The basic circuit is shown below:

w.wang 45
 Zero Bias Operation
(b) Zero Bias Operation Vo=0 - Rl<<Rd, load line
The generated photocurrent flows through Rl which is fixed. The resultant voltage is
therefore linearly dependent on the incident radiation level. One way to achieve
sufficiently low load resistance, and an amplified output voltage, is by feeding the
photocurrent to an operational amplifier virtual ground as shown below. The circuit
has a linear response and has low noise due to the almost complete elimination of
leakage current.

w.wang 46
 Photoconductive
(c) Photoconductive Operation - load line
In the photoconductive mode, the generated
photocurrent produces a voltage across a
load resistor in parallel with the shunt
resistance. Since, in the reverse biased
mode Rd is substantially constant, large
values of Rl may be used still giving a
linear response between output voltage and
applied radiation intensity. This form of
circuit is required for high speed of
response. The main disadvantage of this
mode of operation is the increased leakage
current due to the bias voltage, giving
higher noise than the other circuit modes
already described. (Note that the
photodiode is reverse-biased.)

w.wang 47
 Bias of Photodiode

Photovoltaic
mode or increase voltage
Open circuit like solar cell
mode

Zero bias
mode

Reverse bias
mode or
Photoconductive Ip varies with RL
mode
Cj = r W
48
w.wang W = [2rVbi-VA)(NA+ND)/(q NAND)]1/2
 Minimum detectable power
(Noise floor)

The noise floor is related to the dark current since the dark
current will set the lower limit.

Noise floor = Noise (A)/Responsivity (A/W)

Ip
R 
P
w.wang 49
 Noise in photodetectors

N Ip
h detector eletronics

Radiation noise Internal detector System noise Output

(quantum noise) noise Signal Ip

w.wang 50
 Four noise sources often encountered in
connection with optical detectors.

•Johnson noise

•Shot noise

1/f noise

•Photon noise

w.wang 51
Sources of internal detector noise

Johnson (thermal) noise

1. All resistive materials

2. Depends only on temp. and bandwidth of measuring system

w.wang 52
The Johnson noise contribution is provided by the shunt
resistance of the device, series resistance and the load
resistance. The Johnson noise (thermal noise) is given by:

w.wang 53
Johnson noise is generated by thermal fluctuations in
conducting materials. It is sometimes called thermal noise. It
results from the random motion of electrons in a conductor. The
electrons are in constant motion, colliding with each other and
with the atoms of the material. Each motion of an electron
between collisions represents a tiny current. The sum of all
these currents taken over a long period of time is zero, but their
random fluctuations over short intervals constitute Johnson
noise.

To reduce the magnitude of Johnson noise, one may cool the

system, especially the load resistor. One should reduce the
value of the load resistance, although this is done at the price of
reducing the available signal. One should keep the bandwidth
of the amplification small; one Hz is a commonly employed
value.
w.wang 54
 Shot noise
• Seen in photodiodes under reverse bias (dark
current noise) with no photon input,

I = Isat (eqV/kt –1) = -Id (dark current)

id2 = 2eBId “white noise”
With light: id2 = 2eBIp Ip = eP/(h)

where e = electronic charge and B=detection bandwidth.

w.wang 55
The term shot noise is derived from fluctuations in the stream
of electrons in a vacuum tube. These variations create noise
because of the random fluctuations in the arrival of electrons at
the anode. The shot noise name arises from the similarity to the
noise of a hail of shots striking a target.

In semiconductors, the major source of shot noise is random

variations in the rate at which charge carriers are generated
and recombine. This noise, called generation-recombination
or gr noise, is the semiconductor manifestation of shot noise.
Shot noise may be minimized by keeping any DC component to
the current small, especially the dark current, and by keeping the
bandwidth of the amplification system small.

w.wang 56
 1/f noise
Larger noise powers at lower frequencies.
No theory: not well understood.
Seems to be related to contacts, surfaces, other potential
barrieres

If2 ~ I2B/f

B = bandwidth f = frequency

Usually much smaller than shot noise except at very low

frequency
w.wang 57
The term 1/f noise (pronounced one over f) is used to
describe a number of types of noise that are present
when the modulation frequency f is low. This type of
noise is also called excess noise because it exceeds
shot noise at frequencies below a few hundred Hertz.
The mechanisms that produce 1/f noise are poorly
understood. The noise power is inversely proportional
to f, the modulation frequency. This dependence of the
noise power on modulation frequency leads to the
name for this type of noise.
To reduce 1/f noise, an optical detector should be
operated at a reasonably high frequency, often as high
as 1000 Hz. This is a high enough value to reduce the
contribution of 1/f noise to a small amount.
w.wang 58
 Noise spectrum

1/f

Measured
Squared noise shot
Current
per BW

Johnson

frequency

w.wang 59
As an example: If a photodiode has a dark leakage current of 2 nA and a shunt
resistance of 5x10^8 Ohms, and a responsivity of 0.5 A/W, and letting the
bandwidth of the system be 1 Hz,

Noise-equivalent power (NEP) is a

measure of the sensitivity of a
photodetector or detector system. It
is defined as the signal power that
gives a signal-to-noise ratio of one
in a one hertz output bandwidth.

As an example: If a photodiode has a dark leakage current of 2 nA and a shunt

resistance of 5E8 Ohms, and a responsivity of 0.5 A/W, and letting the bandwidth
of the system be 1 Hz,
Shot noise is the dominant component of the noise current of a reverse-biased
photodiode. This is particularly true at higher voltages. If devices are operated
in a photovoltaic mode with zero bias, the Johnson noise dominates, as dark
current approaches zero. When operating in the zero bias mode the noise current
is reduced such that the NEP, and hence the minimum detectable signal, is reduced
in spite of some loss of absolute sensitivity.
w.wang 60
 p-i-n Photodiodes

Mim Lal Nakarmi, KSU

-As mentioned- increasing deletion layer width improve quantum coefficient

=> Lower doping increase deletion width (higher potential barrier)

w.wang W = [2rVbi-VA)(NA+ND)/(q NAND)]1/2 61

 Avalanche Photodiodes (APD)
I
Avalanche breakdown

High field gain region

Mim Lal Nakarmi, KSU

- APD are designed to provide an internal current gain by impact ionization

- single primary electron/hole generated through absorption of a photon creates
many secondary electrons and holes, all of which contribute to the photodiode current

w.wang 62
 Photodiode array (PDA)

A photodiode array (PDA) is a linear array of discrete photodiodes on an

integrated circuit (IC) chip. For spectroscopy it is placed at the image plane of a
spectrometer to allow a range of wavelengths to be detected simultaneously. In
this regard it can be thought of as an electronic version of photographic film.
Array detectors are especially useful for recording the full uv-vis absorption
spectra of samples that are rapidly passing through a sample flow cell, such as in
an HPLC detector.
PDAs work on the same principle as simple photovoltaic detectors.
w.wang 63
 Position Sensing Detector
Lx

m sensitivity
- limited by
intensity and Ly
beam size

Lx X 1  X 2
X 
2 X1  X 2

Ly Y1  Y 2
Y  
2 Y1  Y 2
w.wang 64
 Charge coupled detector array
(CCD)
Charge Coupled Device was invented in the late 1960s by researchers at Bell Labs,
The CCD's superb ability to detect light has turned it into the industry-standard
image sensor technology.
CCD Basics
CCD imaging is performed in a three-step process:
1. Exposure, which converts light into an electronic charge at
discrete sites called pixels
2. Charge transfer, which moves the packets of charge within the
silicon substrate
3. Charge-to-voltage conversion and output amplification.

w.wang Mim Lal Nakarmi, KSU 65

 Charge coupled detector array
(CCD)

A CCD is an integrated-circuit chip that contains an array of

capacitors (MOSFET) that store charge when light creates e-hole
pairs. The charge accumulates and is read in a fixed time interval.
CCDs are used in similar applications to other array detectors
such as photodiode arrays, although the CCD is much more
sensitive for measurement of low light levels.
w.wang 66
 Charge coupled detector array
(CCD)
An image is projected through a lens onto the capacitor array (the
photoactive region), causing each capacitor to accumulate an electric
charge proportional to the light intensity at that location. A one-
dimensional array, used in line-scan cameras, captures a single slice
of the image, whereas a two-dimensional array, used in video and
still cameras, captures a two-dimensional picture corresponding to
the scene projected onto the focal plane of the sensor. Once the array
has been exposed to the image, a control circuit causes each
capacitor to transfer its contents to its neighbor (operating as a shift
register). The last capacitor in the array dumps its charge into a
charge amplifier, which converts the charge into a voltage. By
repeating this process, the controlling circuit converts the entire
contents of the array in the semiconductor to a sequence of voltages.
In a digital device, these voltages are then sampled, digitized, and
usually stored in memory; in an analog device (such as an analog
video camera), they are processed into a continuous analog signal
(e.g. by feeding the output of the charge amplifier into a low-pass
filter), which is then processed and fed out to other circuits for
transmission, recording, or other processing.
w.wang 67
 Charge coupled detector array
(CCD)
Before the MOS capacitors are exposed to light, they are biased into the depletion region; in n-channel
CCDs, the silicon under the bias gate is slightly p-doped or intrinsic. The gate is then biased at a
positive potential, above the threshold for strong inversion, which will eventually result in the creation
of a n channel below the gate as in a MOSFET. However, it takes time to reach this thermal
equilibrium: up to hours in high-end scientific cameras cooled at low temperature. Initially after
biasing, the holes are pushed far into the substrate, and no mobile electrons are at or near the surface;
the CCD thus operates in a non-equilibrium state called deep depletion. Then, when electron–hole
pairs are generated in the depletion region, they are separated by the electric field, the electrons move
toward the surface, and the holes move toward the substrate. Four pair-generation processes can be
identified:
•photo-generation (up to 95% of quantum efficiency),
•generation in the depletion region,
•generation at the surface, and
•generation in the neutral bulk.
The last three processes are known as dark-current generation, and add noise to the image; they can
limit the total usable integration time. The accumulation of electrons at or near the surface can proceed
either until image integration is over and charge begins to be transferred, or thermal equilibrium is
reached. In this case, the well is said to be full. The maximum capacity of each well is known as the
well depth, typically about 105 electrons per pixel.
w.wang 68
 MOSFET
MOSFET also acts like a voltage
controlled resistor were the
current flowing through the main
channel between the Drain and
Source is proportional to the input
voltage. Also like the JFET, the
MOSFETs very high input
resistance can easily accumulate
large amounts of static charge
resulting in the MOSFET
becoming easily damaged unless
carefully handled or protected.

Enhancement-mode MOSFETs make excellent electronics switches due to their low

“ON” resistance and extremely high “OFF” resistance as well as their infinitely high
input resistance due to their isolated gate. Enhancement-mode MOSFETs are used in
integrated circuits to produce CMOS type Logic Gates and power switching circuits
in the form of as PMOS (P-channel) and NMOS (N-channel) gates. CMOS actually
stands for Complementary MOS meaning that the logic device has both PMOS and
NMOS within its design.
69
Electronics Tutorial
w.wang
 CCD architectures

In a full-frame CCD, the exposure is Frame Transfer

controlled by a mechanical shutter or In a frame-transfer CCD, the entire
strobe. The resultant charges are shifted array is shifted quickly to an
one row at a time to serial register. After a identically sized storage array. The
row is read out by the serial register next read out process from the storage array Charge Transfer
row is shifted to the register for read out. is the same as in a full-frame device, Technique
The process is repeated until all rows are but the frame rates are increased
transferred, at which point the array is because the image array can begin the
ready for the next exposure. next exposure while the readout
process is taking place.

w.wang 70
 complementary metal oxide
semiconductor (CMOS)
Charge is collected in potential well created by applying a
voltage to the polysilicon, or gate electrode. The charge is
confined in the well associated with each pixel by surrounding
zones of higher potential barrier.

Mim Lal Nakarmi, KSU

w.wang 71
 CMOS
Complementary metal–oxide–semiconductor,
abbreviated as CMOS, is a technology for
constructing integrated circuits. CMOS
technology is used in microprocessors,
microcontrollers, static RAM, and other digital
logic circuits. CMOS technology is also used for
several analog circuits such as image sensors
(CMOS sensor), data converters, and highly
integrated transceivers for many types of
communication. In 1963, while working for
Fairchild Semiconductor, Frank Wanlass patented
CMOS (US patent 3,356,858). CMOS is also CMOS inverter
sometimes referred to as complementary-symmetry
metal–oxide–semiconductor (or COS-MOS).[1] The
words "complementary-symmetry" refer to the fact
that the typical design style with CMOS uses
complementary and symmetrical pairs of p-type and
n-type metal oxide semiconductor field effect
transistors (MOSFETs) for logic functions
Cross section of two transistors in a CMOS gate, in
w.wang an N-well CMOS process 72
 Difference between CCD and CMOS
• One difference between CCD and CMOS
sensors is the way they capture each frame.
A CCD uses what's called a "Global
Shutter" while CMOS sensors use a
"Rolling Shutter". Global Shutter means
that the entire frame is captured at the exact
same time.
• In a CCD sensor, every pixel's charge is Teledyne DALSA CCD (left) and CMOS (right) image sensors
transferred through a very limited number
• CMOS sensor, each pixel has its own
of output nodes (often just one) to be
charge-to-voltage conversion, and the
converted to voltage, buffered, and sent off-
sensor often also includes amplifiers,
chip as an analog signal. All of the pixel
noise-correction, and digitization
can be devoted to light capture, and the
circuits, so that the chip outputs digital
output's uniformity (a key factor in image
bits. These other functions increase the
quality) is high.
design complexity and reduce the area
available for light capture. With each
pixel doing its own conversion,
uniformity is lower, but it is also
massively parallel, allowing high total
73
w.wang
bandwidth for high speed.
 Difference between CCD and CMOS

By The Sony Tech Guy

Simplified GIF animation of a CCD image sensor with Interline

Simplified GIF animation of a CMOS image sensor with active
Transfer technology. After the buckets of charge accumulate in the
pixel sensor (APS) technology. Where a CCD converts charge to
individual photo sensors, they are simultaneously transferred into
voltage at the end of the process, a CMOS sensor performs this
the vertical shift registers. Buckets of charge move down the
conversion at the outset. The voltages can then be output over
vertical registers and across the horizontal register. At the end,
compact, energy-saving micro wires.
charge is converted to voltage and amplified.

w.wang 74
 Difference between CCD and CMOS
• One difference between CCD and CMOS
sensors is the way they capture each frame.
A CCD uses what's called a "Global
Shutter" while CMOS sensors use a
"Rolling Shutter". Global Shutter means
that the entire frame is captured at the exact
same time.
• In a CCD sensor, every pixel's charge is Teledyne DALSA CCD (left) and CMOS (right) image sensors
transferred through a very limited number
• CMOS sensor, each pixel has its own
of output nodes (often just one) to be
charge-to-voltage conversion, and the
converted to voltage, buffered, and sent off-
sensor often also includes amplifiers,
chip as an analog signal. All of the pixel
noise-correction, and digitization
can be devoted to light capture, and the
circuits, so that the chip outputs digital
output's uniformity (a key factor in image
bits. These other functions increase the
quality) is high.
design complexity and reduce the
area available for light capture. With
each pixel doing its own conversion,
uniformity is lower, but it is also
massively parallel, allowing high total
75
w.wang
bandwidth for high speed.
 Difference between CCD and CMOS

• CCD became dominant, primarily because

they gave far superior images with the
fabrication technology available. CMOS
image sensors required more uniformity
and smaller features than silicon wafer
foundries could deliver at the time. Not
until the 1990s did lithography develop to
the point that designers could begin making
a case for CMOS imagers again.
• Renewed interest in CMOS was based on Teledyne DALSA CCD (left) and CMOS (right) image sensors
expectations of lowered power
consumption, camera-on-a-chip integration,
and lowered fabrication costs from the
reuse of mainstream logic and memory
device fabrication.
w.wang 76
 Phototransistors
• Built in transistor amplifier
• Operate at zero bias mode

visay

w.wang 77
 Semiconductor
Variable conductivity
A pure semiconductor is a poor electrical conductor as a consequence of having just the right number of electrons to
completely fill its valence bonds. Through various techniques (e.g., doping or gating), the semiconductor can be
modified to have excess of electrons (becoming an n-type semiconductor) or a deficiency of electrons (becoming a p-
type semiconductor). In both cases, the semiconductor becomes much more conductive (the conductivity can be
increased by a factor of one million, or even more). Semiconductor devices exploit this effect to shape electrical current.
Junctions
When doped semiconductors are joined to metals, to different semiconductors, and to the same semiconductor with
different doping, the resulting junction often strips the electron excess or deficiency out from the semiconductor near the
junction. This depletion region is rectifying (only allowing current to flow in one direction), and used to further shape
electrical currents in semiconductor devices.
Energetic electrons travel far
Electrons can be excited across the energy band gap of a semiconductor by various means. These electrons can carry
their excess energy over distance scales of microns before dissipating their energy into heat, significantly longer than is
possible in metals. This effect is essential to the operation of bipolar junction transistors.
Light energy conversion
Electrons in a semiconductor can absorb light, and subsequently retain the energy from the light for a long enough time
to be useful for producing electrical work instead of heat. This principle is used in the photovoltaic cell (e.g. solar cell).
Conversely, in certain semiconductors, electrically excited electrons can relax by emitting light instead of producing heat.
This is used in the light emitting diode.
Thermal energy conversion
Semiconductors are good materials for thermoelectric coolers and thermoelectric generators, which convert temperature
differences into electrical power and vice versa. Peltier coolers use semiconductors for this reason.

w.wang 78
 Infrared Sensor

Infrared light contains the least amount of energy per photon of any other band. Because of this, an infrared photon often lacks
the energy required to pass the detection threshold of a quantum detector. Infrared is usually measured using a thermal detector
such as a thermopile, which measures temperature change due to absorbed energy.

While these thermal detectors have a very flat spectral responsivity, they suffer from temperature sensitivity, and usually must be
artificially cooled. Another strategy employed by thermal detectors is to modulate incident light with a chopper. This allows the
detector to measure differentially between the dark (zero) and light states.

Quantum type detectors are often used in the near infrared, especially below 1100 nm. Specialized detectors such as InGaAs
offer excellent responsivity from 850 to 1700 nm. Typical silicon photodiodes are not sensitive above 1100 nm. These types of
detectors are typically employed to measure a known artificial near-IR source without including long wavelength background
ambient.

Since heat is a form of infrared light, far infrared detectors are sensitive to environmental changes - such as a person
moving in the field of view. Night vision equipment takes advantage of this effect, amplifying infrared to distinguish people and
machinery that are concealed in the darkness.

Infrared is unique in that it exhibits primarily wave properties. This can make it much more difficult to manipulate than
ultraviolet and visible light. Infrared is more difficult to focus with lenses, refracts less, diffracts more, and is difficult to diffuse.
Most radiometric IR measurements are made without lenses, filters, or diffusers, relying on just the bare detector to measure
incident irradiance. 79
w.wang
 Microbolometer
A microbolometer is a specific type of bolometer used as a detector in a thermal camera.
Infrared radiation with wavelengths between 7.5-14 μm strikes the detector material,
heating it, and thus changing its electrical resistance. This resistance change is measured
and processed into temperatures which can be used to create an image. Unlike other types
of infrared detecting equipment, microbolometers do not require cooling

A microbolometer consists of an array of pixels,

each pixel being made up of several layers. IR
absorbing material (resistor), electrode contacts and
bottom layer consists of a silicon substrate and a
readout integrated circuit (ROIC).

The quality of images created from

microbolometers has continued to increase. The
microbolometer array is commonly found in two
sizes, 320×240 pixels or less expensive 160×120
pixels. Current technology has led to the production
of devices with 640×480 or 1024x768 pixels.
w.wang 80
 Thermoelectric effect

The thermoelectric effect is the direct conversion of

temperature differences to electric voltage and vice
versa. A thermoelectric device creates voltage when
there is a different temperature on each side.
Conversely, when a voltage is applied to it, it creates a
temperature difference. At the atomic scale, an applied
temperature gradient causes charge carriers in the
material to diffuse from the hot side to the cold side.
 Thermopile

The thermopile is a heat sensitive device that measures radiated heat.

The sensor is usually sealed in a vacuum to prevent heat transfer except by radiation. A thermopile consists of a number of
thermocouple junctions in series which convert energy into a voltage using the Peltier effect. Thermopiles are convenient
sensor for measuring the infrared, because they offer adequate sensitivity and a flat spectral response in a small package.
More sophisticated bolometers and pyroelectric detectors need to be chopped and are generally used only in calibration
labs.

Thermopiles suffer from temperature drift, since the reference portion of the detector is constantly absorbing heat. The
best method of operating a thermal detector is by chopping incident radiation, so that drift is zeroed out by the modulated
reading.

The quartz window in most thermopiles is adequate for transmitting from 200 to 4200 nm, but for long wavelength
sensitivity out to 40 microns, Potassium Bromide windows are used.
w.wang 82
 Seeback Coefficient
The Seebeck effect is a classic example of an electromotive force (emf) and
leads to measurable currents or voltages in the same way as any other emf.
Electromotive forces modify Ohm's law by generating currents even in the
absence of voltage differences (or vice versa); the local current density is
given by

Where V is the local voltage and is the local conductivity. In general the
Seebeck effect is described locally by the creation of an electromotive field

Where S is the Seeback coefficient , a property of local material and

is the gradient temperature T.

w.wang 83
 Peltier Effect
The Peltier effect is the presence of heating or cooling at an
electrified junction of two different conductors and is named for
French physicist Jean Charles Athanase Peltier, who discovered it in
1834. When a current is made to flow through a junction between
two conductors A and B, heat may be generated (or removed) at the
junction. The Peltier heat generated at the junction per unit time, ,
is equal to

Π Π

Where Π Π are hte Peltier coefficients (how much heat is The Seebeck circuit configured as a
carried per unit charge) at A and B and I is current. Note that the thermoelectric cooler (Peltier effect)
total heat generated at the junction is not determined by the Peltier
effect alone, as it may also be influenced by Joule heating and
thermal gradient effects.

if a simple thermoelectric circuit is closed then the Seebeck effect

will drive a current, which in turn (via the Peltier effect) will always
transfer heat from the hot to the cold junction. The close
relationship between Peltier and Seebeck effects can be seen in the
direct connection between their coefficients: = ST
84
w.wang
 Thomson Effect
In many materials, the Seebeck coefficient is not constant in temperature, and so a spatial
gradient in temperature can result in a gradient in the Seebeck coefficient. If a current is
driven through this gradient then a continuous version of the Peltier effect will occur. This
Thomson effect was predicted and subsequently observed by Lord Kelvin in 1851. It
describes the heating or cooling of a current-carrying conductor with a temperature gradient.

If a current density J is passed through a homogeneous conductor, the Thomson effect

predicts a heat production rate per unit volume of:

Κ ·

Where is the temperature gradient and K is Thomson coefficient This

equation however neglects Joule heating, and ordinary thermal conductivity

w.wang 85
 Full thermoelectric equations
Often, more than one of the above effects is involved in the operation of a real thermoelectric
device. The Seebeck effect, Peltier effect, and Thomson effect can be gathered together in a
consistent and rigorous way, described here; the effects of Joule heating and ordinary heat
conduction are included as well. As stated above, the Seebeck effect generates an
electromotive force, leading to the current equation

)=

To describe the Peltier and Thomson effects we must consider the flow of energy. To start we
can consider the dynamic case where both temperature and charge may be varying with time.
The full thermoelectric equation for the energy accumulation,

· · Π

where is the thermal conductivity. The first term is the Fourier's heat conduction law,
and the second term shows the energy carried by currents. The third term is the heat
added from an external source (if applicable)
w.wang 86
In the case where the material has reached a steady state, the charge and temperature
distributions are stable so one must have both 0 and ·J=0 . Using these facts and the
second Thomson relation (see below), the heat equation then can be simplified to

= · Κ · J)-TJ·

The middle term is the Joule heating, and the last term includes both Peltier ( at junction)
and Thomson ( in thermal gradient) effects. Combined with the Seebeck equation for J ,
this can be used to solve for the steady state voltage and temperature profiles in a
complicated system. If the material is not in a steady state, a complete description will also
need to include dynamic effects such as relating to electrical capacitance, inductance, and
heat capacity.

w.wang 87
 Thomson relation
In 1854, Lord Kelvin found relationships between the three coefficients, implying that the Thomson,
Peltier, and Seebeck effects are different manifestations of one effect (uniquely characterized by the
Seebeck coefficient).

The first Thomson relation is - S,

Where T the absolute temperature, K is the Thomson coefficient,  is the Peltier coefficient, and S is
the Seebeck coefficient. This relationship is easily shown given that the Thomson effect is a continuous
version of the Peltier effect. Using the second relation (described next), the first Thomson relation
becomes

The second Thomson relation is

This relation expresses a subtle and fundamental connection between the Peltier and Seebeck effects. It
was not satisfactorily proven until the advent of the Onsager relations, and it is worth noting that this
second Thomson relation is only guaranteed for a time-reversal symmetric material; if the material is
placed in a magnetic field, or is itself magnetically ordered (ferromagnetic, antiferromagnetic, etc.), then
the second Thomson relation does not take the simple form shown here.

The Thomson coefficient is unique among the three main thermoelectric coefficients because it is the
only one directly measurable for individual materials. The Peltier and Seebeck coefficients can only be
easily determined for pairs of materials; hence, it is difficult to find values of absolute Seebeck or Peltier
coefficients for an individual material. 88
w.wang
 Pyroelectric
The incident radiation is absorbed in a
ferroelectric material which has molecules
with a permanent electric dipole moment. The
net electric polarization present is temperature
dependent (below the a critical temperature
characteristic of the material). When
configured as a capacitor in a circuit, changes
in polarization induced by temperature
changes in the material can be detected by
measuring the change in the charge on the
plates of the capacitor. Pyroelectric detectors
can be made with response times in the
nanosecond region and with a wavelength
response extending out to » 100 ¹m. They
have proved very useful as low cost, robust IR
detectors in such uses as first detection and
intruder alarms.
w.wang 89