ENGLISH Quick Start Guide - ATV 61

S1B8697400

DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• Read and understand this quick start guide before performing any procedure with this drive.
• The user is responsible for compliance with all international and national electrical code requirements with respect to grounding of all
equipment.
• Many parts of this drive, including the printed circuit boards, operate at the line voltage. DO NOT TOUCH. Use only electrically insulated tools.
• DO NOT touch unshielded components or terminal strip screw connections with voltage present.
• DO NOT short across terminals PA/+ and PC/- or across the DC bus capacitors.
• Before servicing the drive:
- Disconnect all power, including external control power that may be present.
- Place a "DO NOT TURN ON" label on all power disconnects.
- Lock all power disconnects in the open position.
- WAIT 15 MINUTES to allow the DC bus capacitors to discharge.
- Measure the voltage of the DC bus between the PA/+ and PC/- terminals to ensure that the voltage is less than 42 Vdc.
- If the DC bus capacitors do not discharge completely, contact your local Schneider Electric representative. Do not repair or
operate the drive
• Install and close all covers before applying power or starting and stopping the drive.
Failure to follow these instructions will result in death or serious injury.

Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by
Schneider Electric for any consequences arising out of the use of this product.
Information below is designed to use single drive connected to single asynchronous motor with a motor cable length less than 50 meters (164ft).
In any other case, consult the drive installation manuals (1760643 or 1760655) and programming manual (1760649) on www.schneider-electric.com.

1 Check the delivery of the drive

• Remove the drive from the packaging and check that it has not been damaged.

WARNING
DAMAGED DRIVE EQUIPMENT
Do not operate or install any drive or drive accessory that appears damaged.
Failure to follow these instructions can result in death, serious injury, or equipment damage.

• Check that the drive reference printed on the label matches the delivery note and corresponding purchase order.

Write the drive Model Reference: _____________ ___________and Serial Number: ____________________________
ATV61HU15N4
1.5KW - 2HP - 380/480V

2 Check the line voltage compatibility

• Check that the line voltage is compatible with the supply range of the drive.
Line voltage _______ Volts Drive voltage range _______ Volts
Drive range: ATVpppppp M3 = 200/ 240 V three-phase - ATVpppppp N4 = 380 /480 V three-phase 8B0917121134

ATVpppppp Y = 500 /690 V three-phase - ATVpppppp S6 = 500 /600 V three-phase

3 Mount the drive vertically

h1u

uh3

ATV61H h1 h2
D55M3X, D75M3X, mm (in.) mm (in.) ATV61H h3 h4
100 (3.9) 100 (3.9) mm (in.) mm (in.)
D90M3X, D90N4, C11N4 D18M3X to D45M3X,
C13N4, C16N4, C22N4, 150 (5.9) u h4 u h4 D22N4 to D75N4
C11Y, C13Y, C16Y, C20Y 150 (5.9) U30Y to D90Y 100 (3.9) 50 (1.9)
C25N4, C31N4, C25Y, 200 (7.8) 150 (5.9) 075M3 to D15M3X,
C31Y, C40Y 075N4 to D18N4,
U22S6X to U75S6X
h3

C40N4, C50N4 300 (11.8) 250 (9.8)

C63N4, C50Y, C63Y, 400 (15.7) 250 (9.8)
u

C80Y
h2u

Free space in front of the drive: 10 mm (0.4 in.) minimum

Install the drive vertically at ± 10°.

For a surrounding air temperature up to 50 °C (122°F), see installation manual ( 1760643 or 1760655)
on www.schneider-electric.com for other thermal conditions.

www.schneider-electric.com 1/4 S1B86974 - 04/2012

 4 Connect the drive: Power 5 Connect the drive: Control
• Wire the drive to the ground.
• Check circuit breaker rating or fuse rating (See SCCR annex S1B86981). by external reference
• Check that the motor voltage is compatible with the drive voltage. Motor
voltage ______Volts.
(Fr1 = Al1 )
0,6 N.m
• Wire the drive to the motor.
5.3 lb.in
• Wire the drive to the line supply.
• Wire the speed reference:

COM
AI1+
+10 v

AI1-
3 200...690 Vac

or
• Wire the command:
Source
Control command 2-wire:
Parameter tCC = 2C SW1 Ext
Sink
Int

LI1: forward
LI2: reverse

... N.m
... lb.in
ATVpppppp

+24

LI1

LI2
See installation manual
(1760643 or 1760655) on
www.schneider-electric.com
or on the drive nameplate for
tightening torque.

DANGER
HAZARD OF FIRE OR ELECTRIC SHOCK
• To avoid overheating or loss of contact, connections must be carried out according to the cable sizes and tightening torques visible on the
label stuck on the ATVpp.
• The use of multi-wire cable without a lug is forbidden for the mains connection.
• Carry-out a pull out test to check that terminal screws are correctly tighten.
Failure to follow these instructions will result in death or serious injury.

6 Apply power to the drive

• Check that Logic Inputs are not active (LI1, LI2, see drawing 5 ).
• Apply power to the drive.
• At first power up, it's displaying the drive state.

RDY Term +0.00Hz 0.0A RDY Term +0.00Hz 0.0A

5 LANGUAGE 2 ACCESS LEVEL
English ENT Basic ENT

Français Standard
ATV61HU15N4
3 seconds Deutsch Advanced
1.5kW/2HP 380/480Vac
Config. n°1 Español Expert
Italiano
<< >> Quick << >> Quick

Switches to [5 LANGUAGE] menu

Display for 3 seconds
automatically after 3 seconds. Switches to [2 ACCESS LEVEL] menu
following power-up
Select the language and press ENT

RDY Term +0.00Hz 0.0A RDY Term +0.00Hz 0.0A

With integrated display terminal.
1 DRIVE MENU MAIN MENU
ESC
1.1 SIMPLY START 1 DRIVE MENU At first power ON
1.2. MONITORING
1.3. SETTINGS
2 ACCESS LEVEL E
2 times 3 OPEN / SAVE AS
rdY
1.4. MOTOR CONTROL
4 PASSWORD
1.5. INPUTS / OUTPUTS CFG
5 LANGUAGE ESC ENT

Code << >> Quick Code Quick

Switches to [1 DRIVE MENU] Press ESC to return to [MAIN MENU]. SIM-

www.schneider-electric.com 2/4 S1B86974 - 04/2012

 7 Set motor parameters for asynchronous motor.
• See on the motor Nameplate to set the following parameters .
Menu Code Description Factory setting Customer
setting
bFr [Standard mot. freq]: [50Hz IEC] 50
Standard motor frequency (Hz)
nPr [Rated motor power]: drive rating
Nominal motor power on motor nameplate (KW)
UnS [Rated motor volt.]: drive rating
Nominal motor voltage on motor nameplate (Vac)
SIM- nCr [Rated mot. current]: drive rating
[1.1 SIMPLY START] Nominal motor current on motor nameplate (A)
FrS [Rated motor freq.]: 50
Nominal motor frequency on motor nameplate (Hz)
nSP [Rated motor speed]: drive rating
Nominal motor speed on motor nameplate (rpm)
ItH [Mot. therm. current]: drive rating
Motor thermal protection current on the motor's rating plate (A)

Menu Code Description Factory setting Customer

setting
SIM- Set [Auto tuning] (tUn) parameter to YES. Auto-tuning is
tUn performed as soon as possible, then the parameter automatically nO
[1.1 SIMPLY START]
changes to [Done] (dOnE).

DANGER WARNING
HAZARD OF ELECTRIC SHOCK OR ARC FLASH DAMAGED DRIVE EQUIPMENT
• During auto-tuning, the motor operates at rated • Asynchronous motor: It is essential that the following parameters
current. UnS, FrS, nCr, nSP and nPr are correctly configured before starting
• Do not service the motor during auto-tuning. autotuning.

Failure to follow these instructions will result in • Synchronous motor: It is essential that the following parameters
death or serious injury. nCrS, nSPS, PPnS, PHS, LdS and LqS are correctly configured
before starting autotuning.
• When one or more of these parameters have been changed after
auto-tuning has been performed, YES will return to dOnE and the
procedure will have to be repeated.

Failure to follow these instructions can result in death, serious injury, or

equip-ment damage.

8 Set basic parameters

Menu Code Description Factory setting Customer
setting
ACC [Acceleration]: 3.0
Acceleration time (s)
dEC [Deceleration]: 3.0
SIM- Deceleration time (s)
[SIMPLY START] LSP [Low speed]: 0
Motor frequency at minimum reference (Hz)
HSP [High speed]: 50
Motor frequency at maximum reference (Hz)

9 Start the motor

ATVpppppp Graphic display terminal Integrated display terminal
E
RDY Term+38.0Hz 0.0A
LI2
+24

LI1

LI1: forward Frequency ref. 38.0

+ 38.0 Hz

Code Quick

www.schneider-electric.com 3/4 S1B86974 - 04/2012

Menus structure
Access level
Comparison of the menus that can be accessed on the graphic display terminal/integrated display terminal

Graphic display terminal Integrated display [2. ACCESS LEVEL] (LAC-)

terminal
[2 ACCESS LEVEL] LAC-
[3 OPEN/SAVE AS] -
[4 PASSWORD] COd-
[5 LANGUAGE] -
[1 DRIVE MENU] [1.1 SIMPLY START] SIM-
[1.2 MONITORING] SUP-
[1.3 SETTINGS] SEt-
[1.11 IDENTIFICATION] -
[1.12 FACTORY SETTINGS] FCS-
[1.13 USER MENU] USr-
A single function can be assigned to each input.

AdU[Advanced]
drC-

EPr[Expert]
bAS[Basic]

(factorysetting)
[1.4 MOTOR CONTROL]

Std[Standard]
[1.5 INPUTS / OUTPUTS CFG] I-O-
[1.6 COMMAND] CtL-
[1.7 APPLICATION FUNCT.] FUn-
[1.8 FAULT MANAGEMENT] FLt-
[1.9 COMMUNICATION] COM-
[1.10 DIAGNOSTICS] -
[1.14 PROGRAMMABLE CARD] (1) PLC-
[6 MONITORING CONFIG.] -
A single function can be assigned to each input.
[7 DISPLAY CONFIG.] -
Several functions can be assigned to each input
Expert parameters EPr-
Several functions can be assigned to each input.

(1) can be accessed if the PLC card is present.

Accessing SIMPLY START and parameters.

A dash appears after menu and submenu codes to differentiate them from parameter codes.
Example: [1.1 SIMPLY START] (SIM-), [2/3 wire control] (tcc) parameter.

Power-up
XXX Displays the state of the drive

ENT
ESC ENT

SIM- SIMPLY START Simplified menu for a fast startup

Menus ESC
ESC ENT

ESC
Refer to the programming manual
(1760649) for comprehensive menu
description.

Certificate CE/ATEX e
ATV61H CE Certificate
See on www.schneider-electric.com
ATV61W CE Certificate 07ATEX0004X
ATV61E5 CE Certificate

www.schneider-electric.com 4/4 S1B86974 - 04/2012