BHS RPM
BHS RPM
Experience
We have been manufacturing crushers and mills for over
100 years. About 50 years ago, we specialized in impact
crushing. The primary focus of our technical development and
application expertise is on our vertical-shaft impact crushers.
Worldwide service
BHS provides fast and reliable service around the world,
complete with technical customer support and a large inventory
of spare parts for all common machine types, including older
models.
www.bhs-sonthofen.com
ROTOR IMPACT MILL
4
BHS rotor impact mills are not only used in the production
of sand for the dry mortar industry. They have also proved
themselves useful in the production of surfaces for sports
facilities, as well as in the milling of fertilizers from limestone,
dolomite, gypsum, anhydrite and burnt lime.
Functional Description
Rotor Impact Mill RPM Rotor Impact Mill RPMF – the pulverizer
The input material is fed into the machine from above at the The pulverizer uses the same crushing principle as the RPM.
center. When it impacts the rotor, the material is accelerated The difference is that the rock is exposed to more intense
towards the outside through centrifugal forces; there, the stress through a combination of higher circumferential speed
horseshoe-shaped hammers hit it and throw it against the and a narrower milling gap. The result, in percentage terms, is
anvil ring. Here, in the milling gap, it is crushed as a result of a higher proportion of fine sand.
the impact and shearing forces. The material leaves the rotor
through the gap and falls down through two outlet chutes.
Adjustable gap
A set of replaceable spacers is used to configure the ring gap.
The ongoing wear and tear of the impact hammers causes the
gap width to change; this can be easily corrected by replacing
spacers in different sizes (shown in red in the illustration).
RPM 1113 for the production of concrete sand (0–2 mm) from gravel (16–32 mm)
100%
90%
Input material
80% Final product
70%
60%
Sieve fraction
50%
40%
30%
20%
10%
0%
0,09
0,13
0,25
0,50
0,71
1,00
2,00
3,15
5,00
8,00
11,20
16,00
22,40
31,50
45,00
Comparison of RPM 1513 and RPMF 1516 for the production of dry mortar sand (0–1.6 mm) from limestone (8–20 mm)
100%
90%
Input material
80% Final product RPM 1513
70% Final product RPMF 1516
60%
Sieve fraction
50%
40%
30%
20%
10%
0%
1,00
1,60
0,06
0,25
2,00
4,00
8,00
11,20
16,00
0,09
0,16
0,32
0,50
0,71
22,40
31,50
RPM 1113 for the production of high-quality crushed sand (0–2 mm) from off-spec gravel fractions (2–5 mm, andesite)
100%
90%
Input material
80% Final product
70%
60%
Sieve fraction
50%
40%
30%
20%
10%
0%
0,09
0,13
0,16
0,25
0,50
0,71
1,00
1,25
1,40
1,60
2,00
2,80
3,15
4,00
5,00
5,60
EXAMPLES OF USE
11
www.bhs-sonthofen.com
Use of two RPM 1513 rotor impact mills in a dry-mortar plant in the United Arab Emirates (UAE)
Five BHS rotor impact mills of the RPM 1513 type are in use at a dry-mortar plant in Thailand
OPTIONS AND ACCESSORIES
12
Intensive cooling
In the event of high ambient temperatures or if the material to
be processed is hot, a supplementary lubrication unit featuring
a larger storage volume and stronger cooling power can be
provided.
Air cannon
In order to reduce material deposits in the outlet area, the
crusher can be optionally equipped with air cannons.
Control system
As an alternative to integrate the machine into the plant
control a BHS PLC control (including touchscreen) and a
frequency converter can be supplied if required. This allows
an autonomous operation and monitoring of the machine's
function.
Periphery
We can also provide the steel construction, storage bunker and
metering equipment, feed and discharge equipment, and dust
capture systems – all adapted to your specific applications.
13
www.bhs-sonthofen.com
Performance data
Rotor diameter Number Circumferential speed Drive power Throughput rate 1) Input size 2)
Type
x height of hammers (max.) (max.) (max.) (max.)
Type A B C D E Weight 3)
1)
The throughput rate depends on the circumferential speed of the rotor and the grading curve of the input material.
2)
The input size depends on the type of rock, the circumferential speed of the rotor, and the percentage of maximum particle size in the grading curve
(screened through square mesh).
3)
Weights refer to the standard design without motor and accessories.
E
BHS FIELDS OF COMPETENCE
www.bhs-sonthofen.com