See discussions, stats, and author profiles for this publication at: https://www.researchgate.

net/publication/316277838

Comparison of IC Logic Families

Chapter · April 2017

CITATIONS READS

0 16,940

1 author:

Shree Krishna Khadka

Tribhuvan University
35 PUBLICATIONS   11 CITATIONS   

SEE PROFILE

Some of the authors of this publication are also working on these related projects:

PhD Research Proposal and Proceedings View project

The Socio-Economic Dimension View project

All content following this page was uploaded by Shree Krishna Khadka on 20 April 2017.

The user has requested enhancement of the downloaded file.

 Comparison of Logic Families

Logic Family (Silicon Technology) Introduction Features Limitations

- In common use before the development - Low speed, high power dissipation
1. RTL - First logic family, require minimum number
of ICs. Common Emitter Configuration. - Low fan out, poor noise immunity
(Resistor Transistor Logic) of transistors.
- Logic 1: 1-3.6 V and Logic 0: 0.2V - Operating speed <4MHz.
2. DCTL - Direct coupled transistors. - Simpler than RTL, easy to fabricate. - Small logic swing, poor noise margin.
)

(Direct Coupled Transistor Logic) - Base resistors of RTL are removed. - Fewer components hence economical. - Current hogging
Saturated Logic Families
ON − Saturation Mode
(Bipolar Transistor Technology)

OFF − Cut Off Mode

- First circuit configuration designed into IC.

- Use diodes and transistors.
Transistor Logic Families

3. DTL - Very small in size and high reliability at - No low and constant output impedance
- Input is fed through diodes followed by
(Diode Transistor Logic) very low price. in both states.
transistor at the output side.
- Greater fan out and improved noise margins.
- Use all transistors totem pole output. - Fast switching time, larger fan out. - Large current spike when switching
4. TTL
- Function of diodes in DTL is performed - Reduced silicon chip area. from low to high.
(Transistor-Transistor Logic)
by multi-emitter transistor at input - Easy to interface with other logic families. - Less noise immunity (0.4V)
(

- Merged Transistor Logic (MTL). - High component density, less power

5. IIL - Both PNP and NPN transistors are used. dissipation.
- Poor noise immunity.
(Integrated Injection Logic) - Designed around multi-collector - Low metal interconnection.
inverting transistors. - Used in MSI and LSI designs.
- Non saturated logic/Current mode logic. - Require large silicon area, high power
Non-Saturated Logic - Fastest logic family
6.ECL - Compliment output/eliminates the need dissipation (high cost).
ON − Active Mode - Used in very high frequency applications.
( ) (Emitter Coupled Logic) of inverter. - Inconvenient voltage levels.
OFF − Cut Off Mode - No noise spikes, large fan out.
- Logic 1: -0.8 and Logic 0: -1.7 - Low noise margins.
7.MOS Logic - Use pMOS, nMOS or both with high
- Lower power dissipation. - Larger propagation due to high output
MOS Logic Families (Metal Oxide Semiconductor packaging density.
- Shorter rise and fall times. impedance.
(Unipolar Transistor Technology) Logic) - Easy to design and fabricate
- Large fan-out. - Noise margin is around 1V.
- Less power drawn due to gate dielectric.

Parameter RTL IIL DTL HTL TTL ECL MOS CMOS

Basic Gate NOR NOR NAND NAND NAND OR-NOR NAND NOR-NAND
Fan Out 5 Depends on Injector Current 8 10 10-20 25 20 20-50
Power Dissipation 12 mW 6 nW – 70 uW 8-12 mW 55 mW 10 mW 40-55 mW 0.2-10 mW 0.025-1.01 mW
Noise Immunity Nominal Poor Good Excellent Very Good Poor Good Very Good
Propagation Delay 12 nSec 25-30 nSec 30 nSec 4 nSec 10 nSec 1-2 nSec 300 nSec 70 nSec
Clock Rate 8 MHz - 72 MHz 4 MHz 35 MHz +60 MHz 2 MHz 10 MHz
Speed X Power 144 Less than 1 300 - 100 100 60 70

View publication stats