Mark-V Ground Fault Rectification

MARK-V GROUND FAULT
RECTIFICATION CASE STUDY
Adeel Imtiaz
FFC, Pakistan
INTRODUCTION
MARK-V control system is installed on one of our two gas turbines. Mark-V
125VDC supply ground problem appeared intermittently for past few
years. In Turnaround 2010 instrument team rectified this ground fault.
This report gives a brief overview of nature of job performed by
INSIDE THIS ISSUE instrument team. The report also presents a comparative analysis of
complexity of ground fault rectification procedure in MARK-II and MARK-V
1 Introduction system.
2 Background BACKGROUND
Mark-V has two main types of power supply sources
3 125VDC ground fault repair
• 125VDC
4 MARK-II vs MARK-V
• 125VAC
125VDC is further regulated to ±24 VDC, ±15 VDC and 5VDC.
125VDC continuously monitored by a ground detector soft relay L64D. In
case positive or negative pole of supply set out limit then 125VDC SUPPLY
GROUND FAULT alarm appears in MARK-V <I> alarm list.
“MARK-V system gives
valuable ground fault
diagnostic information
and voltage level
variation”
L64D Energized
In above picture it is clear that 125VDC positive terminal ground

contact L64D_P was energized actuating L64D ground detector soft
relay.
125VDC GROUND FAULT RECTIFICATION
Above piece of information was further verified by the voltage on

both poles of 125VDC with respect to ground. This information is also
available on DIAGNOSTIC software module (DIAGC).
“Speedtronic and
Thermocouple Ground
Faults do not exist in
MARK-V system.”
MARK-V <I> DIAGNOSTIC SCREEN
TERMINAL AS FOUND ACCEPTABLE NORMAL

VOLTAGE VOLTAGE IMPEDANCE
(VDC) RANGE (VDC) (KΩ)
POS-GND 15 More than 31 33
NEG-GND -117 Less than -31 33
P15-COM 14.75 17 to 13 -
N15-COM -14.90 -17 to -13 -
P24-COM 28.43 28 to 22 -
N24-COM -30 -24 to -22 -
P5-COM 5 7 to 4 -
MEASURED VOLTAGE LEVELS
Above values shows that positive and negative poles with respect to
ground are out of acceptable range. Since only 15VDC developed
across positive pole and ground which refers to the grounding of
positive pole.
No ground detector is installed for regulated supplies of ±24VDC,

±15VDC and 5VDC in MARK-V system. These supplies are protected
with fuses and under voltage alarms.

MARK-V system is composed of six cores and one protective interface
module. Each core has a maximum of four terminal blocks. Analog IOs are
terminated on processor<R>, communication <C> and protection <P> CORE
cores while digital IOs are terminated on <QD> and <CD>. 125VDC is TBs
supplied to each core and terminal block by power distribution core
<PD>.
POWER
CABLE
MARK-V Cores & Terminal Block
<QD> <CD>
125VDC Power Cables to TBs
The goal of this procedure was to disconnect all TBs and cores from
power distribution core one by one till L64D reset.
• The procedure started by disconnecting 125VDC power cables to
terminal block DTBA of <QD> core. Two multi-meters were also
placed to measure supply against ground. L64D did not reset.
• In the next step power cable of terminal block DTBB of <QD> was
removed but L64D did not reset.
• In this way all the digital inputs of <QD> core were isolated.
Digital inputs on <CD> core were to be disconnected in the next
phase.
• The L64D relay was reset when power cable was disconnected
from terminal block DTBA of <CD> core.
L64D Relay Reset

• DTBA contained 19 pairs of cables which were suspicious. Each pair was
removed one by one to narrow down the fault. It revealed that out of 19
pair 14 pairs were grounded.
• On the basis of analysis it was concluded that positive grounded supply
cable coming from field is looped in JB-2 from where ground fault is
spread to every field device looped from JB-2 terminal block as shown in
the picture. The figure shows that a single grounded sensor 26QAA
caused ground fault in all loops due to cable looping at JB-2.
JB-2
• To identify the root cause cables were disconnected from JB-2: TB-A. As
soon as the cable from grounded switch 26QAA atomizing air high
temperature was disconnected L64D reset, “125VDC Battery Ground” 26QAA SWITCH
alarm disappeared while “Atomizing air high temperature” alarm
initiated.
• On field inspection 125VDC supply cable was found damaged and switch
was in bad conditions. Voltages were sinking to ground from both cable
and switch. Cable was repaired and protected. Switch power terminal to
ground resistance was 2KΩ, far less than MARK-V ground threshold
(33KΩ). Switch was bypassed.
26QAA SWITCH
Ground Fault Detection Comparison

The Speedtronic regulated supplies are contained to MARK-V cabinet
through few jigs whereas thermocouples are directly terminated on
input TBs while logic is implemented in software. Therefore,
Speedtronic & Thermocouple ground fault does not exist in MARK-V
system which makes it less vulnerable to ground faults as shown in
the table. Recently we also removed 125VDC ground fault in MARK-II
a hence a comparison is given below
26QAA SWITCH
125VDC GROUND MARK-V MARK-II

Fault Detection Time 3 hours 48 Hours
Cables Disconnected 24 300
Fault Tracing Systematic Hit & trail
Ground Fault Detects which pole is Detects only
Information grounded and also shows ground fault
live voltage values
Field/JB Cable Topology Same Same
SPEEDTRONIC GROUND
Speedtronic Ground Does not Exist Probable
Fault
SGDD CARD/Soft Relay Non YES
SPD. Fault Det. Time - >90 Hours
Cables Disconnected - >680
Thermocouple GROUND
THRM. Ground Fault Does not Exist Probable
CONCLUSION
Mark-V 125VDC ground fault was detected in three hours while same
activity in MARK-II took more than 48 hours. A clear difference in number
of cables/modules disconnected was also observed in both cases.
MARK-II Thermocouple, Speedtronic and 125VDC circuits are
floating/ungrounded systems. Any ground fault occurrence in these
circuits can cause damage to human and equipment. On the other hand
MARK-V system possesses only 125VDC ungrounded circuit. Speedtronic
and thermocouple circuit are shifted to MARK-V soft logic.
Consequently, MARK-V control system architecture makes it less
susceptible to ground faults.
However field cable structure and JB looping does not have much
difference in both systems. Improvement in filed cable topology and JB
looping can reduce the 125VDC ground detection time in both systems.

Mark-V Ground Fault Rectification

Uploaded by

Copyright:

Available Formats

Mark-V Ground Fault Rectification

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Mark-V Ground Fault Rectification

Uploaded by

Copyright:

Available Formats

MARK-V GROUND FAULT

RECTIFICATION CASE STUDY

In above picture it is clear that 125VDC positive terminal ground

Above piece of information was further verified by the voltage on

TERMINAL AS FOUND ACCEPTABLE NORMAL

No ground detector is installed for regulated supplies of ±24VDC,

125VDC GROUND FAULT RECTIFICATION

MARK-V Cores & Terminal Block

L64D Relay Reset

Ground Fault Detection Comparison

125VDC GROUND MARK-V MARK-II

You might also like