Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

HPD Low Power

Download as pdf or txt
Download as pdf or txt
You are on page 1of 98

Divisione S.B.C.

HPD
HPD2, HPD5, HPD8,
HPD16

User’s manual

rev. 7
January 1997
software rel. 18
HPD EXTENDED
VOLTAGE RANGE

HIGH PERFORMANCE DRIVE


DIGITAL-LOCK
VARIABLE RATIO
1

X4

12 POSITIONER

M + -

STEP MOTOR
1
SIMULATION
X5
X1
X6

10 X7

1 1 EASY
MAINTENANCE

X2 X3

TORQUE CONTROL

20 20

ACCELERATION
CONTROL

SOFTWARE & HARDWARE


SPINDLE ORIENTATION
EXPANSION FOR TOOL CHANGING

RS-485 or RS-422 SERIAL LINK


BUILT-IN P.L.C.

Parker Hannifin S.p.A.


Divisione S.B.C.
Via Gounod, 1 – 20092 Cinisello B. HPD :
everywhere
(Milano) – Italy
Phone: +39-02-66012478
Fax: +39-02-66012808

for any
E-mail: drivesbc@parker.com

application
WARNING

HIGH VOLTAGE !
Certain circuits in the H P D drive carry dangerously high voltages that could cause serious personal
injury or death.
Do not attempt to service any parts of the drive when it is connected to the power supply.
If you need to access internal parts, before working on the drive allow at least 15 minutes after
power-down to allow the DC bus capacitors to discharge. It is the User’s responsibility to make
sure that the installation is executed in accordance with established industrial health and safety
standards.
In relation to the interpretation of standards, note that the drive is considered as a component and
not as a machine.

Any tampering or unauthorised modification of the drive will invalidate the guarantee immediately.
Guarantee cover is otherwise provided for 1 (one) year.

This instruction manual is applicable to the standard version of the drive.

Parker Hannifin S.p.A. - Divisione S.B.C. declines all liability for any whatsoever form of damage
caused by inappropriate use of the drive.

Installation and maintenance of the drive and connected


equipment must be performed exclusively by qualified and
trained personnel with basic skills in electronics.

Commissioning of the drive must performed exclusively by


qualified and trained personnel with advanced skills in
electronics and drive technology.

Training courses can be supplied by Parker Hannifin S.p.A. - Divisione S.B.C. on request.

The quoted performance of the HPD drive is guaranteed


only when used with series MB synchronous motors
manufactured by Parker Hannifin S.p.A. - Divisione S.B.C.

ISBN0204101609
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

CONTENTS:

1 INTRODUCTION ...................................................................................... 5

1.1 General information..................................................................................... 5


1.2 Product description...................................................................................... 5
1.3 Direct mains connection.............................................................................. 6
1.4 Identification................................................................................................ 6
1.5 Main hardware characteristics..................................................................... 7
1.6 Software features......................................................................................... 8
1.7 Compliance with EMC standards................................................................ 8
1.8 Safety........................................................................................................... 8

2 INSTALLATION........................................................................................ 9

2.1 Safety instructions....................................................................................... 9


2.2 Interference suppression hints...................................................................... 10
2.3 Mains filter installation instructions............................................................ 10
2.4 Control cubicle layout example................................................................... 12
2.5 HPD drive mains filters............................................................................... 13
2.6 Terminal assignments.................................................................................. 20
2.7 Power connections....................................................................................... 22
2.8 Power connection layout.............................................................................. 23
2.9 Signal cable connections............................................................................. 23
2.10 Signal cable connection layout.................................................................... 24
2.11 Frequency input connection......................................................................... 24
2.11.1Encoder emulation...................................................................................... 25
2.12 Serial line connection................................................................................... 26
2.13 Braking resistor…….................................................................................... 26
2.14 Backup......................................................................................................... 27

3 PARAMETERS AND PROGRAMMING.................................................. 28

3.1 Using the keypad......................................................................................... 29


3.2 Commissioning the HPD drive.................................................................... 30
3.3 Basic parameters.......................................................................................... 33
3.4 Basic commands.......................................................................................... 38
3.5 Calibrating speed loop................................................................................. 39
3.6 Operating modes.......................................................................................... 45
3.6.1 Torque control............................................................................................. 45
3.6.2 Acceleration control.................................................................................... 45
3.6.3 Maintenance and commissioning................................................................. 46
3.6.4 Positioner..................................................................................................... 47
3.6.5 Digital locking............................................................................................. 49
3.6.6 Stepper motor emulation............................................................................. 51
3.6.7 Spindle orientation...................................................................................... 52
3.7 Block diagrams............................................................................................ 52
3.8 Digital input and output programming........................................................ 59
3.8.1 Pico-PLC...................................................................................................... 59

4
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

3.8.2 Examples and applications........................................................................... 63


3.9 Programming with Pcbrush.......................................................................... 79

4 SERIAL INTERFACE............................................................................... 80

4.1 Communication protocol............................................................................. 80


4.2 Serial addresses and parameter lengths....................................................... 85

APPENDIXES

A HPD drive mechanical dimensions.............................................................. 87


B MB series motor connectors........................................................................ 88
C Hardware characteristics.............................................................................. 89
D DC bus voltage thresholds........................................................................... 90
E Conventions................................................................................................. 90
F Software timers............................................................................................ 91
G Pico-PLC default program........................................................................... 92
H Flash information......................................................................................... 93
I S.B.C. filter physical dimensions…............................................................. 94
L Remote communications interface…........................................................... 96
M Application description form....................................................................... 97

5
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

1 - INTRODUCTION

1.1 General information

This manual describes operations required for the installation and commissioning of the HPD
(High Performance drive) drive for brushless motors. Read all chapters of the manual carefully
before using the drive.

1.2 Product description

The HPD drive is a digital frequency converter for driving AC brushless motors. The adoption of
a Parametric Operator Interface makes drive configuration procedures faster and easier to repeat.
The large number of configuration possibilities makes the drive suitable for numerous applications.

A high power 16 bit micro-controller allows speed control with the characteristics required of a
servo controller, plus a range of auxiliary functions that can help reduce the presence of control
electronics in the application and thus permit considerable economic savings.

In addition to the positioner functions with trapezoidal profile, digital lock, spindle orientation,
stepper motor emulation, torque control and acceleration control, the HPD drive also has an internal
pico-PLC. The pico-PLC adopts the most diffused industrial programming standards and offers
considerable freedom for use of inputs and outputs. It also enables users to develop a range of
additional functions that are not among the basic features of the drive.

The HPD drive is complete with an RS-422/RS-485 serial interface which can be used for
configuration, monitoring, or simultaneous transmission of commands to a multiple system comprising
up to 32 HPD drives.

In addition to the above functionality, the HPD drive is designed as an open system with the
facility to accommodate hardware and software expansion cards. For further information on
currently available expansion cards contact Parker Hannifin S.p.A. - Divisione S.B.C. directly or
your local Dealer.

6
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

1.3 Direct mains connection

The HPD series of drives is specifically designed for direct connection to a three-phase mains
power supply from 90 to 460V~ 50/60 Hz, without interposing transformers. It is the responsibility
of the User to connect the system via protection fuses. The use of single phase power supplies is
permitted although motor power output must be derated in this case. Maximum motor power is
calculated by the following formula:
Pmax = 27 ⋅ 10-3 Vmains 2 [watt].
All protections required for safety, such as overvoltage detection, short circuit fault protection and
inverter and motor overtemperature detection are integral with the drive.
Mains filters and motor filters must be calculated during the design of the electrical cubicle so that
EMC standards are met in order to qualify for CE marking.
Chapter 2 provides a detailed view of problems related to EMC.
N.B. leave at least 60 sec. after switching the drive off before switching it
on again.

1.4 Identification

HPD drives are available in 4 models: HPD 2, HPD 5, HPD 8 and HPD 16. The number that
follows HPD is the value of drive rated current in amperes.

HPD drives carry an identification plate on the right hand side showing all
essential information for correct identification of the unit. Make a note of
the information on this plate before consulting S.B.C. on technical
matters.
The identification plate is shown below.

model
identification plate

7
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

1.5 Main hardware specifications

Parameter U.M. Value


Power supply V~ 90..460
HPD2 HPD5 HPD8 HPD16
Models
Rated output current A 2 5 8 16
Peak output current (4 s) A 4 10 16 32
Output power (400 V~ ) kW 1 2.5 4.1 8.3
Control electronics dissipation W 18
Dissipation from power components W 25 60 89 158
Ambient temperature oC 45
Braking resistor internal / external
Rated power of braking resistor W 120
Feedback resolver (speed 1)
Power stage switching frequency KHz 8
Maximum output frequency Hz 450
Protection category IP 20
Digital inputs 24V No 8
Digital outputs 24V -100mA PNP N o 6
Voltage-free digital outputs N o 1
Encoder emulation RS-422 steps/rev 128..16384
Frequency / sign or encoder input KHz 800 / 200
Analogue reference V ±10 diff 15 bit
Auxiliary analogue input V ±10 diff 10 bit
Analogue monitor output V ±10 - 8 bit
Tacho generator emulation output V ±10 V
Serial line RS-422 / RS-485
Backup for encoder emulation V 24 d.c.
Backup for encoder emulation A max. 2

8
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

1.6 Software features

The following capabilities are implemented in the basic software supplied with the HPD drive:

• Speed control
• Advanced torque limit manager
• Speed windows management
• Positioning with trapezoidal speed profile
• Digital locking functions with variable transmission ratio and phase shifting
• Spindle orientation
• Stepper motor emulation
• Torque control with overlaid speed control
• Acceleration ramp control with overlaid speed control
• Simplified maintenance and start-up mode
• Internal PLC for advanced input/output programming functions

1.7 Compliance with EMC standards


Immunity:

EN50082-1* / EN50082-2 Basic immunity specifications


IEC1000-4-2 (ex IEC 801-2) level 3 Electrostatic discharge immunity
IEC1000-4-3 (ex IEC 801-3) level 3 Electromagnetic field immunity
IEC1000-4-4 (ex IEC 801-4) level 4 Fast transient burst conducted immunity

Compatibility:

EN50081-1* / EN50081-2 Basic radio interference specifications


EN55011 group 1, class A Measurement limits for radio interference
EN55011 group 1, class B* Measurement limits for radio interference

1.8 Safety

Safety standard EN60065

Low voltage Directive 73/23/CEE amended by 93/68/CEE


Applied standard EN60204-1

* Conformity for use in domestic or industrial surroundings depends on the nature of the installation.

9
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

2 - INSTALLATION

• The HPD drive must be installed in a vertical position (power terminal block X4 at the top).
• Leave at least 190 mm clearance above and below the drive.

2.1 Safety instructions

• Make sure the drive is correctly sized for the motor you intend to connect. Compare rated
voltage and current.
• Wire up electrical panel/drive/motor in accordance with the instructions in this section of the
manual, taking into consideration EMC requirements and established safety legislation.
• The User is responsible for installing fuses on the drive A.C. power supply.
• Power conductors and control circuits must be kept apart (at least 20 cm) and, when they must
cross, intersections must be at a right angle. Motor lines and mains power lines must never be
parallel.
• All power conductors must be sufficiently sized (refer to table in heading 2.7; in all cases
compliance with IEC227-2 must be guaranteed).
• Conductors connected to the system by means of the terminal strip must not be soldered
(EN60065, art.15.3.5).
• Make sure drive and motor and properly earthed.
• Make sure that the maximum voltage on terminals L1, L2, L3 does not exceed rated voltage by
more than 10% in the worst possible case (see EN60204-1, section 4.3.1). Excessively high
mains feeding voltage can damage the drive.
• Do not detach electrical connections when the drive is connected to the power supply.
• Follow all installation instructions in this manual step by step. If you are in doubt, contact S.B.C.
customer service.
• Dangerous voltages may remain for 60 seconds after mains disconnection and system power-
down; do not touch power cables during this interval.
• Do not open the drive casing. This action is potentially dangerous and will automatically invalidate
the guarantee.

Installation and wiring must be carried out with the entire electrical panel
disconnected from the power supply. Make sure that the drive enable
command is disconnected from the emergency circuit. Qualified
technical personnel must preside when the power panel is powered up for
the first time.

10
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

2.2 Interference suppression hints

Because of the high speed voltage wavefronts in PWM, high levels of stray current may
sometimes flow through capacitive couplings and earth systems. Stray currents of this type can affect
other functional units. It is therefore prudent to calculate the presence of an amount of spurious
energy that depends on the size of the system (drives, motor lines, motor). Spurious energy generates
EM radiation that can interfere with the operation of nearby systems. Existing standards do not set
down limits for this type of radiation.

Preventive measures

Basic methods for preventing interference are: decoupling of drive from its surroundings, high
quality and properly sized conductors to neutralise voltages (earthing), and adequate shielding.
Shields, filters and drives must have a large contact area to achieve the maximum possible decoupling
and hence optimal noise suppression. Attention must be paid, however, to the entire installation, as
this is one of the most important precautions in assuring efficient noise suppression.
High frequency interference takes the form of radiation, especially from the motor lines. This
effect can be reduced with the use of shielding.
Another essential counter-measure for noise suppression is the use of filters.
The use of filters is aimed at reducing conducted interference on wiring and the return of
conducted interference to source (drive) through routes offering the lowest impedance. This method
provides effective protection for other systems connected to the same electrical line, also protecting
the drive from interference originating from other systems. When installing filters consider the mains
input and motor feeding output; the motor feeding output can be protected with output filters that
minimise interference levels (generally torroidal ferrite core coils bearing several windings of all three
motor wires).

2.3 Mains filter installation instructions

To guarantee electromagnetic compatibility in compliance with the relevant standards the


maximum priority must be awarded to EMC requirements when designing the control cubicle. To
obtain the best results from filters follow the instructions in this section carefully, because

even a complex and expensive filter is ineffective unless it is


installed taking EMC aspects into consideration.
Avoid:

- routing noise emitting cables parallel to “clean” cables


- parallel cables, especially in the vicinity of the filter (ensure physical separation)
- cable loops (keep cables as short as possible and close to the common potential).

11
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Additional measures

- With the exception of mains cables to the filter, all power and control wiring must be shielded
and, wherever possible, kept segregated (minimum distance 20 cm). If control and power cables
must cross, the intersection must be at a right angle.
- Shielded cables must be installed on a copper bar by means of a high conductivity wire clamp.
The area of contact must be as large as possible and the shield must be unbroken. In general the
shield should be connected at each extremity. In certain circumstances, however, control cable
shields may be connected only at one end to eliminate mains hum that could interfere with the control
signal. Decide case by case as numerous factors must be considered. Adopt the following general
approach: if the shield is solely for shielding, connect at both ends. If current flowing in the shield
interferes with the shielded signals, connect at one end only.
- The incoming cable must be connected to an earth terminal by means of a screw to ensure
proper contact between shield and earth.
- RF interference suppression filters must be installed as close as possible to the drive and must
have a large area of contact with the power panel or the baseplate. Remove all paint. The filter earth
terminal must be connected to the earth bar along the shortest possible route.
- As far as possible keep the power side (drive) and control side (PLC or NC) physically
separated by separating the metal mounting plates. Do not route any cables through the mounting
plates.

Protective measures for drives with > 3.5mA dispersion current per phase

Interference currents dispersed through the earth system may be considerable in certain
conditions. Therefore, make sure all suppression filters are properly earthed before they are
connected. Cable sizes must be in line with the requirements of safety standards.
If a suppression filter is permanently connected and current dispersion during normal operation is
greater than 3.5mA (which would be expected with most drives) adopt one of the following
measures additionally:
a) Increase shield size to at least 10 mm².
b) Install a detection system to monitor the shield and automatically disconnect the drive in the
presence of faults.
c) Install a second conductor in parallel (electrically) with the shield using separate terminals.

The installer must ensure that filter terminals are protected.

12
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

2.4 Control cubicle layout example

All conductors down-line of the mains filter must be shielded


and mounted to a copper bar with large contact area. Also the
copper bar must present an ample area of contact with the
cubicle mounting plate.

Large surface area partition shield with generous contact area


around perimeter. Remove paint from contact points in the
cubicle.

keep separate as far as possible

mains
filter
cable
control
cable
30 cm
max.

drive

motor
cable
Cubicle interior or mounting plate

POWER CONTROL

13
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

2.5 HPD drive mains filters

S.B.C. has developed a special series of filters for HPD drives. When the filters are installed in
accordance with our instructions, compliance with EN55011-class A is guaranteed; for class B
rating add a transformer to the power supply (shielded primary and secondary). Users must allow
space in the control cubicle to accommodate filters implemented at the time of the project. S.B.C.
filters provide both mains and motor output filter functions.

Filters of different manufacture can also be utilised. In this case S.B.C. offers its technical
support by testing the filter you intend to use and generating a test data report.

CERTIFIED FILTER CONFIGURATIONS IN COMPLIANCE WITH EN55011 (group


1 classes A and B)

High attenuation S.B.C. three-phase filters are specifically designed for S.B.C. brushless motor
drives in compliance with the standard IEC950 for stray current up to 3.5 mA (380 - 50 Hz) for
semi-static equipment.

TECHNICAL FEATURES

Enclosure metal
Temperature -25 … +85 oC
Rated voltage 460 V~ 50/60 Hz

S.B.C. FILTERS
type current enclosure
SBC3R10 mains 10 F6
SBC3R20 mains 20 F10
SBC3R35 mains 35 F7
SBC3RD35 mains 35 F5
SBC3M10 motor 10 F6
SBC3M20 motor 20 F6

14
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

SYMMETRICAL
MINIMUM GUARANTEED ATTENUATION
ASYMMETRICAL
MEASUREMENT MIL STD 220 A

dB

110

100

90

80

70

60

50

40

30

20

10

0.01 0.1 1 10 100 1000 10000

KHz
SBC3R10

SYMMETRICAL
MINIMUM GUARANTEED ATTENUATION
ASYMMETRICAL
MEASUREMENT MIL STD 220 A

dB

110

100

90

80

70

60

50

40

30

20

10

0.01 0.1 1 10 100 1000 10000

KHz
SBC3R20

15
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

SYMMETRICAL
MINIMUM GUARANTEED ATTENUATION
ASYMMETRICAL
MEASUREMENT MIL STD 220 A

dB

110

100

90

80

70

60

50

40

30

20

10

0.01 0.1 1 10 100 1000 10000

KHz
SBC3R35

SYMMETRICAL
MINIMUM GUARANTEED ATTENUATION
ASYMMETRICAL
MEASUREMENT MIL STD 220 A

dB

110

100

90

80

70

60

50

40

30

20

10

0.01 0.1 1 10 100 1000 10000

KHz
SBC3RD35

16
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

RESONANT FREQUENCY

Kohm

100

10

0.1

0.01

0.01 0.1 1 10 100 1000 10000

KHz
SBC3M10

RESONANT FREQUENCY

Kohm

100

10

0.1

0.01

0.01 0.1 1 10 100 1000 10000

KHz
SBC3M20

17
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Configuration 1 Class A

drives
mains filter motor filter
MAINS

SBC3RXX HPD SBC3MYY


M

HPD SBC3MYY
M

HPD SBC3MYY
M

HPD SBC3MYY
M
Where HPD rating is between 2 and 16 A

XX can be 10, 20 or 35 and stands for the mains filter rated current;
the sum of drive rated currents must not exceed the mains filter
rated current.

YY can be 10 or 20 and represents the motor filter rated current


the drive rated current must not exceed that of the filter

PMM 8010

MHz dBuV
.01 .1 1 10 30
120

90

60

30

Limit: C22_A_QP Title: DEFINIT4 Date: 06-25-1995

18
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Configuration 2 Class A

drives
mains filter
MAINS

SBC3RD35 HPD
M

HPD
M

HPD
M

HPD
M
Where HPD rating is between 2 and 16 A

the sum of drive rated currents must not exceed 35 A

PMM 8010

MHz dBuV
.01 .1 1 10 30
120

90

60

30

Limit: C22_A_QP Title: DEFINI13 Date: 06-25-1995

19
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Configuration 3 Class B

drivesi
mains filter motor filter
MAINS

SBC3RD35 HPD SBC3MYY


M

HPD SBC3MYY
M

HPD SBC3MYY
M

HPD SBC3MYY
M
Where HPD rating is between 2 and 16 A

The sum of drive rated current values must not exceed 35 A

YY can be 10 or 20 and represents the motor filter rated current;


drive rated current must not exceed that of the filter
PMM 8010

MHz dBuV
.01 .1 1 10 30
120

90

60

30

Limit: C22_B_QP Title: DEFINI12 Date: 06-25-1995

20
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

2.6 Terminal assignments

X4 power

12

1 X5 serial interface

resolver
X1

X6 encoder in
10

X7 encoder out

1 1

analog signals and digital outputs

X2 X3 control voltages and digital inputs

20 20

21
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Terminal board X1 Terminal board X4


1 motor PTC + ( 24 V ) 1 LIVE 1
2 motor PTC - 2 LIVE 2
3 resolver Excit. high 3 LIVE 3
4 resolver Excit. low 4 U PHASE
5 resolver Sin high 5 V PHASE
6 resolver Sin low 6 W PHASE
7 resolver Cos high 7 A-BUS
8 resolver Cos low 8 B-BUS
9 0V 9 BRAKE COMMAND
10 0V 10 INTER. BRAKE RESISTOR
11 + DC BUS
12 - DC BUS

Terminal board X2 Terminal board X3


1 reference high 1 + 10 V - 10 mA max
2 reference low 2 0V
3 0V 3 - 10 V - 10 mA max
4 Aux reference high 4 0V
5 Aux reference low 5 + 24 V - IN
6 0V 6 0V
7 Aux. analogue output 7 0V
8 0V 8 + V backup
9 tacho output 9 - V backup
10 0V 10 0V
11 digital out 0 11 drive enable
12 digital out 1 12 digital input 1
13 digital out 2 13 digital input 2
14 digital out 3 14 digital input 3
15 digital out 4 15 digital input 4
16 digital out 5 16 digital input 5
17 digital out 6 A 17 digital input 6
18 digital out 6 B 18 digital input 7
19 + 24 V - OUT 200 mA 19 + 24 V - OUT 200 mA
20 0V 20 0V

D type X5 D type X6 D type X7


1 TX 1 A 1 PHA
2 RX 2 /A 2 /PHA
3 /TX 3 B 3 PHB
4 /RX 4 /B 4 /PHB
5 5 -BRA 5 PHC
6 +BR 6 +BRB 6 /PHC
7 -BR 7 0V 7 0V
8 0V 8 -BRB 8
9 0V 9 +BRA 9

22
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

2.7 Power connections


For the motor cable consider
Choice between cable for fixed or floating installation.
Cable must be shielded and suitably sized in terms of insulation and wire sections.
Reticulated polypropylene is the preferred insulation material.
Length (max 100 m); note that conductor-conductor capacitance must not exceed 8 nF.
If cable length exceeds 50 m install a triple 1 mH inductance between drive and motor with rated
current identical to HPD rated current.
Minimum conductor size is 1.5mm2 for HPD2 and HPD5 , 2.5mm2 for HPD8 and 4mm2 for
HPD16.

For the mains power cable


Power cables must not be shielded.
Minimum conductor size is 1.5mm2 for HPD2 and HPD5, 2.5mm2 for HPD8 and 4mm2 for
HPD16.
Input fuses must be rated as follows:

MODEL Slow blow fuses


(A)
HPD2 6
HPD5 10
HPD8 16
HPD16 20

Resolver cable
The cable must comprise 4 twisted pairs with individual shields and one common shield.
Capacitance for the length of cable must not exceed 10 nF; wire size must be no less than
0.35mm2.
Maximum length is 100 m.

EMI filter connection


The connection between filter and drive must never exceed 30 cm. If the distance is less than 15
cm unshielded cables are possible, otherwise a shielded cable must be used.

Earth connections
To reduce the length of individual conductors that must be connected to earth we recommend
using an earth busbar located as near as possible to the drive.
The busbar must be made of copper to
Length (m) width (mm) thickness
ensure low inductance. It must also be
(mm)
mounted on insulated fixings. The adjacent
table shows minimum dimensions according to 0.5 20 6
length. 1 40 6
1.5 50 6

23
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

2.8 Power connection layout

EARTH STUD
MAINS SCREW

EMC filter

FERRITE CORE

*
B
C TOROIDAL COIL
A
12
D
X4
E

MOTOR

H J
G K
C
A
D B
E F

10

RESOLVER X1

SERVOMOTOR DRIVE

FERRITE COIL, MOTOR FILTER OR NO PROTECTION

* ACCORDING TO CHOSEN CONFIGURATION

2.9 Signal cable connections

A twisted and shielded pair must be employed for the analogue reference.
The cable for emulated encoder signals must comprise three twisted pairs with a common shield.
Normal cables can be used for digital inputs/outputs.

Minimum size of all signal wires is 0.35mm2

24
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

2.10 Signal cable connection layout

MOTION HPD
CONTROLLER
REF+ 1
Reference out
REF- 2 X2 - Reference in
3

A 1
/A 2
B 3
Encoder in /B 4 X7 - Encoder out
C 5
/C 6
7

24Vdc

Output

11
13
X3 - Inputs
Enable
19

11
Input X2 - Outputs

20

TO EARTH BAR

2.11 Frequency input connection

The RS-422 type frequency input can be software-configured in two modes: the first (default) to
accept quadrature signals from encoders, the second is frequency/direction mode (see chapter Basic
parameters bit b42.5).
In the former case follow this connection diagram:
HPD
8

A 1
X6
A 2

B 3

B 4

0V 7

In the case of parallel connections to more than one HPD, connections to pins 9, 5, 6, and 8,
must be made only on the last drive in the group.

25
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

If the frequency/direction mode configuration is adopted, channel A is dedicated to frequency


while channel B handles direction. Frequently, a 24V interface is preferred to an RS-422 serial port.
Using push-pull configuration, the conversion can be implemented on the external connector by
following this wiring diagram:

+24Vdc

3K9 3K9
2K2

PULSES 1

DIR 3

2K2 4

470 470
5 X6
6

HPD connection with digital locking

X7 (HPD) master X6 (HPD) X6 (HPD)

1 A 1

2 A 2

3 B 3

4 B 4

7 GND 7

see text for burden resistors

The example in the figure shows the connection between two HPD drives in digital lock with a
master, but this configuration can be extended to several drives connected in series. On the final
drive in the series connect the burden resistors by jumpering pin 1 with pin 9, pin 2 with pin 5, pin 3
with pin 6 and pin 4 with pin 8 on connector X6. The master can be an externally fed encoder, or the
simulated encoder output on another drive.
The signal from the master encoder must be differential type 5V RS-422; it is therefore possible
to connect a maximum of 10 slave HPDs.
If the master is an HPD drive, then up to 32 units can be connected in digital lock mode using the
same simulated encoder signal (RS-422 standard).
For the relative programming of the HPD, consult the Digital locking chapter in this manual.

2.11.1 Encoder emulation

On connector X7 there are signals of encoder emulation phase A, phase B and phase C
(reference zero). The signals are RS-422 type. For the relative programming of pulses per revolution
consult the Basic parameters chapter in this manual, bit b42.0, b42.1 and b42.2 (default = 1024
pulses/revolution).

26
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

2.12 Serial line connection

The HPD drive serial line can be configured as RS-422 or RS-485 depending on the connection.
In both cases termination resistors must be used (150 Ω). Where more than one HPD drive is
connected to the bus the final node must be terminated as shown below. The two cases are
illustrated in the following diagrams.

RS-485
MASTER X5 X5 X5

TX
RX
/TX
/RX

+BR
-BR
0V
0V

NODE 1 NODE n LAST NODE

RS-422
MASTER X5 X5 X5

TX
RX
/TX
/RX

+BR
-BR
0V
0V

NODE 1 NODE n LAST NODE

2.13 Braking resistor

HPD drives are equipped with an integrated braking resistor. The effective use of the braking
resistor can be checked by monitoring the value of parameter Pr37, which is expressed as a
percentage. If you intend to dissipate more power, use an external braking resistor. To connect up
the system (which must be carried out in conditions of complete safety) disconnect the jumper
between terminals 9 and 10 of terminal board X4; connect one end of the resistor to terminal 9 and
the other to terminal 11on X4. The external resistor value must be 40 ohm and a thermal magnetic
circuit breaker must be installed between resistor and drive. The minimum wire size for the
connection is 4 mm2; the connection cables should be as short as possible and, in any event, no
longer than 3 metres.

27
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

2.14 Backup

When you need to keep the drive electronics powered up during mains losses, for example to
maintain the simulated encoder function, certain precautions are necessary.
A) Use an external 24V d.c. 2 A power supply.
B) Ensure that the drive is not started up with the backup voltage, which is only intended to maintain
it in standby. To ensure this condition use the setup shown in the following figure.
C) When mains voltage is restored the drive must not be enabled until 10 seconds have elapsed.
When the mains fails the HPD will generate an undervoltage alarm; example 11 in the Examples
and applications chapter indicates a method for resetting this alarm automatically ensuring a 10
second delay.

CONNECTION OF BACKUP POWER SUPPLY

HPD

8
9

X3
24Vdc-2A

19
20

24V relay

28
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

3 - PARAMETERS AND PROGRAMMING

The features: torque, speed, acceleration and position control are the task of a dedicated electronic
circuits. In this chapter you can see how to set up and the meaning of any parameter, functional
block diagrams and advanced functions description too.
In the figure below it is described the general block diagram of the drive’s functions that you can
configure by parameters.

analogue
b40.2 TORQUE DEMAND
digital REFERENCE LIMIT SWITCH SPEED
&
internal MANAGER REGULATOR
STOP

TORQUE
OPERATING
LIMIT
MODE
MISCELLANEOUS MANAGER

SPEED
TRIPS
WINDOWS
MANAGER
Pr31

DIGITAL SPINDLE
TORQUE ACCEL. MAINT. POSITIO. STEPPER EXTERN.
LOCK ORIENT.
MODE MODE MODE MODE MODE
MODE
MODE MODE

See chapter Block diagrams for a better description of how to use the drive, especially for
operating modes. See chapter Pico-PLC to understand how to connect peripheral systems
(inputs/outputs) to the parametric system of the HPD drive.

Parameters are divided as follows:

from Pr0 to Pb42 basic parameters


from Pr50 to Pb70 operating mode parameters
from Pr71 to Pb99 pico-PLC parameters
from In0 to In63 pico-PLC instructions

The principal parameter units and resolutions are:

parameter unit resolution


speed revolutions per minute 1
acceleration seconds / 1000 rpm. 0.001
position 4096 steps / revolution 1/4096 revolution
current % of the drive peak current 0.1

29
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

3.1 Using the keypad

The keypad-display module is designed to provide an intuitive operator interface. It can be used
to program operating data, monitor system status and enter commands.
The module has only three keys, located at the top of the front panel just below the display. The
keys are marked: [M], [+] and [-].
[M] is used to change the display mode and consequently also the function of [+] and [-].
There are two display modes: parameter mode and parameter value mode.
When the unit is powered up, provided there are no active alarms, the message “IdLE” (drive
disabled) or “run” (drive enabled) is displayed; this is also the position of parameter Pr0.
Press [+] or [-] to scroll through the parameters.
If you want to check a parameter value, press [M]; when the value is shown it can be updated
using [+] and [-].
To return to parameter mode press [M] again.
The display can be shown in various forms, depending on the parameter in question.
If you need to increase (or decrease) a parameter value quickly, press [M] while the up key [+]
(or down key [-] ) is pressed.

HPD keypad
M
IDLE XXXXX
M
+ -

M + +1 M +9
Pr. 01 XXXXX
M - -1 M -9

+ -

M + +1 M +9
Pr. 02 XXXXX
M - -1 M -9

+ - +
M + 1
Pb. 40 b40.XX M XX
M - 0
-
+
M + done
Pb. 99 b99.XX M XX
M
-
+ -
+ + + +

In. 00 M PLC inst. M 1st oper. M 2nd oper. M 3rd oper. M

- - - -

In. XX

30
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

In addition to the parameter values and the pico-PLC instructions, the display may show the
following messages:
r. xx At the time of power-up this message indicates the software version installed (2 seconds
approx.).
IdLE At power-up and in correspondence with Pr0 this message shows that no alarms are
present and the system is disabled.
run At the time of power-up and in correspondence with Pr0 this message indicates that no
alarms are present and the drive is enabled; the motor shaft may be spinning.
Er. xx In correspondence with Pr0 this message indicates that the drive has detected an alarm (xx
indicates the alarm code) and has therefore been disabled. When an alarm is detected the
display automatically switches to parameter Pr0 and shows the alarm code.
dcbuS In correspondence with Pr0 this message indicates that the drive is not operating at low
voltage (b40.10=0) and that DC bus voltage is still below the 120 V threshold; the inrush
current circuit is still connected so the drive is not yet ready (b41.4=0).
Prxx Indication of parameter xx (value displayed by pressing “M”).
Pb. xx Indication of bit parameter xx.
bxx.yy Indication of bit yy of parameter xx; press “M” to display bit status.
In. xx Indication of instruction xx of PLC program.
donE Displayed for approximately 1 second each time a command is entered.
rESet Displayed for approximately 1 second each time an alarm reset command is entered
(b99.10).
tESt Displayed during wiring test (b70.3).
rEtrY It’s displayed when a writing error is detected storing the pico-PLC instructions (b99.14)
or while saving parameters (b99.15).

3.2 Commissioning the HPD drive

The steps described in this section must be followed carefully when the drive is started up for the
first time.
1) Connect the motor to the drive in compliance with the wiring diagrams in the manual.
2) Make sure the drive is disabled (terminal 11 of board X3 must be open)
3) Power up the drive.
4) After some seconds the display shows “IdLE”.
5) Setting essential parameters:
Pr33 calculation (rated current)
InM
Pr33 = ⋅ 100
InD ⋅ 2

where: InM is rated motor current at zero rpm in Ampere


InD is rated drive current in Ampere
The maximum value of Pr33 is 50.0

Pr19 calculation (peak current)


Pr19MAX = Pr33⋅ 3

31
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

The maximum value must be no higher than three times the value of Pr33

Pr29 calculation (number of poles)


Use the following table for MB series motors

Flange ( mm ) Pr29
56 4
70 4
105 8
145 8
205 8

Pr32 calculation (rated speed)

If Pb 42.6=0 Pr32 = Vmax ⋅ 1.12


ω ⋅ VMAIN
If Pb 42.6=1 Pr 32 = ⋅ 8.3
VMOT
where: ω is nominal motor speed in rad/sec
Vmain is HPD power supply in Vrms
Vmot is motor rated voltage in Vrms

Evaluation of Pr16 and Pr17 (speed regulator gain)


The default values of Pr16 and Pr17 have been chosen considering identical motor and drive
rated currents; if this is not the case correct the values of parameters Pr16 and Pr17 with the
ratio of the motor rated current/drive rated current. Preventive execution of this compensation
will eliminate the risk of motor vibration at the first start-up.
6) Set the analogue reference signal to 0 V (terminals 1, 2 of board X2), and enable the drive (24
V on terminal 11 of board X3 ).
7) The motor shaft must be stopped; when the analogue reference voltage is changed motor speed
should change proportionally. If this is not the case check your wiring.
8) Save your changes with b99.15.

The drive is preset with default values designed to meet the requirements of the majority of
applications. With the default values the pico-PLC in the drive runs the program described in
appendix G, so the following functions will be present on the input and output terminal boards:

TERMINAL BOARD X2 TERMINAL BOARD X3


11 real speed > Pr13 11 start drive
12 motor speed = reference (+/- 20 rpm) 12 left-hand stroke end (n. c.)
13 real speed = 0 13 right-hand stroke end (n. c.)
14 real speed > 0 14 emergency stop (n. c.)
15 motor thermal image active (i2t) 15 clockwise/counter-clockwise rotation
16 16 start / stop
17 terminal A drive ready 17
18 terminal B (n.c. contact) 18

32
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

The functions on terminals 12, 13 and 14 must be enabled by setting bit b90.10 to one. This
requires access to the extended parameters menu.
The default PLC program controls parameter Pr5 in addition to timer 1 (Pr92) and bits b40.0,
b40.4, b40.5, b40.6, b40.12 so in this case the above binary parameters and switches cannot be
utilised unless the pico-PLC is disabled (b99.13=0) or the basic program is modified.

Short and extended menu

When the HPD drive is in default status, only a limited number of parameters are displayed.
These parameters are the only ones required for applications in which the HPD is employed as a
straightforward frequency converter, i.e. you are not using the advanced functions of the drive (e.g.
using HPD with a Numerical Control or an intelligent axis control card). Switch between short and
extended menu using b99.6.
Short memory parameters are:
Pr0 Real speed of motor shaft in rpm.
Pr1 Analogue reference offset (terminals 1 and 2 of terminal board X2 ).
Pr2 Analogue reference full scale: speed value in rpm corresponding to 10 V reference signal.
Pr8 Acceleration/deceleration ramp values in seconds per 1000 rpm
Pr16 Integral gain of speed control loop.
Pr17 Speed control loop damping.
Pr19 Peak current delivered to drive expressed as a percentage of the peak rated value of the
drive.
Pr29 Number of motor poles.
Pr32 Rated speed (rpm).
Pr33 Rated current that can be delivered by the drive (can be maintained indefinitely) expressed
in percent of the peak rated current of the drive.
Pr35 Instantaneous current requested by the motor expressed as a percentage of drive peak
rated current.
b99.6 Enable extended menu. Default=0. Set to 1 to obtain the extended menu.
b99.7 Security. Default=0. Set to 1 to protect parameters from modification.
b99.10 Alarm reset command.
b99.13 PLC status. Default=1. At 1 the PLC program is executed, at 0 the program is not
executed.
b99.15 Parameter storage command.

Using extended menu you can manage all parameters and pico-PLC instructions.

Restoring default parameters

If you need to restore the factory-set default parameter values:


- disable the drive via hardware (open terminal 11 on board X3)
- power-up the system
- the display will show “IdLE” after approximately 3 seconds
- set b99.7 and b99.13 to zero
- enter command b99.12
- save your changes with b99.14 and b99.15.

33
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

3.3 Basic parameters


To access all the following parameters open the extended menu by setting b99.6 to one. For this
procedure, b99.7 must be set to zero.

DECIMAL PARAMETERS

Pr0 Motor speed: this is a read-only parameter expressed in rpm; the message Pr0 never
appears on the display. In its place a message corresponding to drive status is shown.
Pr1 Analogue reference offset. This is expressed in input A/D converter counts.
Programming limits are -10000 and +10000 while the range of the A/D converter is from -
16384 to +16383 over ± 10 V.
Pr2 First full scale of analogue reference. Unit=rpm, range=±10000, default=3000. If
b40.0=0 and b40.12=0, Pr7 will be equal to: Vin ⋅ Pr2 / 9.76 where Vin is the voltage on
the analogue input.
Pr3 Second full scale of analogue reference. Unit=rpm, range=±10000, default=-3000. If
b40.0=1 and b40.12=0, Pr7 will be equal to: Vin ⋅ Pr3 / 9.76 where Vin is the voltage on
the analogue input.
Pr4 Frequency reference full scale (connector X6). Unit=rpm, range=±32767,
default=3000. If b40.12=1 and b40.13=1, Pr7 will have the following value:
if b42.5=0 Pr7 = Fin ⋅ Pr4 / 2000000 (frequency/direction signal)
if b42.5=1 Pr7 = Fin ⋅ Pr4 / 500000 (quadrature signal)
where Fin is the frequency on the encoder input.
Pr5 Internal reference. Unit=rpm, range=±9000, default=0. If b40.12=1 and b40.13=0, Pr7
will be the same as Pr5.
Pr6 Reserved read-only speed reference. Unit=rpm, range=±9000. If b40.2=1 Pr6 is only
utilised as a speed reference for the control loop. The active operating mode will enter its
speed request in parameter Pr6.
Pr7 Main reference (read-only parameter). Unit=rpm, range=±9000. If b40.2=0, Pr7 is used
as a reference for the speed control loop. In certain operating modes Pr7 can be used as a
reference for other factors (torque / acceleration). In this case Pr7 is expressed in a suitable
unit.
Pr8 Acceleration ramp for positive speed values. Unit=s/krpm range=0.002..65.535,
resolution=0.001 s, default=0.002 s. Acceleration for positive speeds required of the
motor by way of the speed reference is internally limited so that acceleration of 1000 rpm
takes Pr8 seconds.
Pr9 Deceleration ramp for positive speed values. Unit=s/krpm, range=0.002..65.535,
resolution=0.001 s, default=0.002 s. Deceleration for positive speeds required of the
motor by way of the speed reference is internally limited so that deceleration of 1000 rpm
takes Pr9 seconds.
Pr10 Acceleration ramp for negative speed values. Unit=s/krpm, range=0.002..65.535,
resolution=0.001 s, default=0.002 s. Acceleration for negative speeds required of the
motor by way of the speed reference is internally limited so that acceleration of 1000 rpm
takes Pr10 seconds.
Pr11 Deceleration ramp for negative speed values. Unit=s/krpm, range=0.002..65.535,
resolution=0.001 s, default=0.002 s. Deceleration for negative speeds required of the
motor by way of the speed reference is internally limited so that deceleration of 1000 rpm
takes Pr11 seconds.

34
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Pr12 Deceleration ramp for stroke end and stop functions . Unit=s/krpm,
range=0.002..65.535, resolution=0.001 s, default=0.002 s. Deceleration required of the
motor by the stroke limit and stop functions is internally limited so deceleration of 1000 rpm
takes Pr12 seconds.
Pr13 Overspeed threshold. Unit=rpm, range=0..+13000, default=3500. If the absolute value
for motor speed exceeds the value entered in Pr13, b41.0 must be =1, otherwise it will be
= 0.
Pr14 High speed threshold. Unit=rpm, range=±13000, default=20. When b40.7=0, if the
speed difference between motor and reference is less than Pr14 and greater than Pr15,
b41.1 will be =1, otherwise it will be = 0. In the case of b40.7=1, if motor speed is less
than Pr14 and higher than Pr15, b41.1 will be =1, otherwise it will be =0.
Pr15 Low speed threshold. Unit=rpm, range= ±13000, default=20. When b40.7=0, if the
speed difference between motor and reference is less than Pr14 and greater than Pr15,
b41.1 will be =1, otherwise it will be =0. In the case of b40.7=1, if motor speed is less
than Pr14 and higher than Pr15, b41.1 will be =1, otherwise it will be =0.
Pr16 Integral gain of speed control loop. Range =0...32767, default=120.
Pr17 Speed control loop damping. Range=0...32767, default=2000. If Pr16 is set to zero
Pr17 sets the value for proportional gain of the speed control loop.
Pr18 Bandwidth limiter. Unit=512µs, range=0..1000, default=1. Use Pr18 to set the time
constant of a first order filter located on the digital torque demand signal. The filter cut-off
frequency will be: 310/Pr18 Hertz.
Pr19 Peak current. Unit=%, range=0..100.0%, resolution=0.1%, default=100.0%. Maximum
current that the drive can deliver to the motor expressed as a percentage of drive peak
current. It is good practice to maintain this value to within 3 times the rated motor current.
Pr20 DC bus voltage. Unit=volt, read-only parameter. Shows the value of DC bus voltage.
Pr21 Torque limiter, read-only parameter. Unit=%. Can be used by operating modes to
restrict motor torque.
Pr22 Auxiliary analogue reference. Unit=%. The displayed value will be Pr22=Vin⋅100/9.76.
Resolution is 0.2%.
Pr23 Alarm code. This code shows the currently active alarm; zero means that no alarms are
active. Consult the table of alarm codes for more details.
Pr24 Last alarm. This parameter stores the last alarm. Pr24 is reset when the alarm reset
command is entered (b99.10).

Alarm code Alarm


0 no alarm
1 overvoltage
2 undervoltage
3 overcurrent
4 resolver alarm
5 motor overheating
6 drive overheating
7 external alarm
8 auxiliary alarm
9 digital output overcurrent alarm
10 PLC check-sum
11 parameter check-sum

35
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Pr25 Code describing installed software version. Read-only parameter.


Pr26 Serial line baud-rate code . Default=8. This is the code for programming transmission
speed. For more information consult the section on the serial interface.
Pr27 Serial line address code . Default=0, possible settings=0..31. For more information
consult the relative section of the manual.
Pr28 Motor shaft position. Unit=steps, range=0..4095. Read-only parameter that shows the
absolute position of the resolver.
Pr29 Number of motor poles. Possible settings=2..64, default=8.
Pr30 Resolver position offset. Default=0; use Pr30 for electronic correction of the mechanical
resolver position.
Pr31 Operating mode. Default=0. Use Pr31 to select the active operating mode. 0 indicates no
operating mode.
Pr32 Rated speed. Unit=rpm, range=0..9000, default=3200. Nominal motor speed. Should be
programmed with the motor speed at which rated voltage corresponds to drive power
feeding voltage reduced by 13%. Consult the formula in section Commissioning the HPD
drive.
Pr33 Motor rated current. Unit=% of peak current, range=10.0..50.0%, resolution=0.1%
default=50.0%. Enter motor rated current.
Pr34 Tacho generator emulation output gain. Default=127. Use parameter 34 to alter
analogue output gain in proportion to speed (terminal 9 on board X2). The analog output
value (Volt) is:
Pr 0 ⋅ Pr 34
tacho = where: K = 1 if Pr32 ≤ 875
K ⋅ 15875 K = 4 if 875 < Pr32 ≤ 3500
K = 16 if Pr32 > 3500
Pr35 Torque monitor. Unit=% of peak torque, resolution 0.1%. This parameter indicates the
percentage of torque (or current) that the motor is delivering.
Pr36 Thermal image of motor winding. Unit=% of reference temperature. This read-only
parameter indicates an estimation of the heat on the innermost windings of the motor. If the
value reaches 100.0 %, which is equal to the nominal value, b41.11 switches to 1 so that
current can be limited to the rated value.
Pr37 Thermal image of braking resistor. Unit=% of nominal temperature. This read-only
parameter indicates an estimation of the heat on the braking resistor. If the value reaches
100.0 % or more, consider using an external braking resistor.
Pr38 Auxiliary analogue output. Unit=% of 9.76V, default=0, range=±100.0%, resolution 8
bit. If b40.11 is equal to 1, the auxiliary analogue output will be equal to 976⋅Pr38/100
volts.
Pr39 Phase correction. This parameter may be used in certain applications with special motors
that are to run also at constant power. Range ±32000, default = 0.

BINARY PARAMETERS

Binary parameter Pb40 can be read, written and saved. Binary parameter Pb41 provides
information regarding system status. Parameters Pb42 and Pb99 are read/write parameters with save
facility.

b40.0 Selecting the first or second speed reference full scale value . Default=0. If set to 0
Pr2 is used to standardise the analogue reference. If set to 1 parameter Pr3 is used.

36
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

b40.1 Activation of algorithm for the suppression of vibration at 0 rpm. Default=0. Set to 1
to activate the algorithm.
b40.2 Selecting user/reserved reference. If set to 1 the reserved reference is used in
accordance with the currently active operating mode. If set to zero the reference selected
by b40.0, b40.12 and b40.13. is employed. Default is 0.
b40.3 Reference freeze . Default=0. If set to 1 the reference will not be updated so that motor
will not follow input reference modifications. If set to zero the reference will follow variation
in the input reference.
b40.4 Left-hand stroke end. Default=0. If set to 1 and the selected reference requires negative
speed, the reference will be forced to zero in accordance with the ramp in Pr12. If set to
zero no type of control is performed.
b40.5 Right-hand stroke end. Default=0. If set to 1 and the selected reference requires positive
speed, the reference will be forced to zero in accordance with the ramp set in Pr12. If set
to zero no control Is performed.
b40.6 Stop function. Default=0. If set to 1 the motor is stopped according to the ramp set in
Pr12.
b40.7 Absolute/relative speed window selection. Default=0. If set to zero speed windows
Pr14 Pr15 b41.1 will operate in relative mode, if set to 1 the speed windows will operate
in absolute mode.
b40.8 Analogue torque limit. Default=0. If set to 1, Pr22, i.e. auxiliary analogue input, will be
used to limit motor torque.
b40.9 Software enable. Default=1. If set to zero the drive cannot be started.
b40.10 Low voltage operation enable. Default=0. If at 1 the inrush current circuit will be
connected each time the drive is disabled, thus permitting rapid increases in power supply
voltage. When the drive is started the inrush current circuit will be connected before the
effective start-up of the power stage. This procedure causes a drive start-up delay of
120ms.
b40.11 Analogue output selector. Default=0. If set to 0 the analogue output will carry a signal
proportional to motor torque. If set to 1 it carries a value proportional to Pr38.
b40.12 Digital/analogue reference selector. Default=0. If set to 0 the analogue input is selected
as the main reference. If set to 1 the reference will be digital and, by means of 40.13, it can
be set for internal or external. If set for an external input, using b42.5 this can be set for
quadrature or frequency/direction.
b40.13 Internal or frequency reference selector. Default=0. If b40.12=1, b40.13 can be set
to 0 to select internal reference, or to 1 to select the frequency input (encoder-in) which, in
turn can be configured as frequency/direction or quadrature signal using b42.5.
b40.14 Serial communication enable. Default=0. Set this parameter to 1 to enable serial comms.
b40.15 Reserved. Must remain on zero.

b41.0 Overspeed. When the absolute motor speed value exceeds the value set in Pr13, b41.0 is
on 1, otherwise it is on 0.
b41.1 At speed. With b40.7=0 if the speed difference between motor and reference is lower
than Pr14 and higher than Pr15, b41.1 will be 1, otherwise it will be 0. With b40.7=1, if
motor speed is lower than Pr14 and higher than Pr15, b41.1 will be 1, otherwise it will be
0.
b41.2 Zero speed. If motor speed (Pr0) is zero rpm, b41.2=1, otherwise b41.2=0.
b41.3 Forward. If motor speed (Pr0) is positive b41.3=1, otherwise b41.3=0.
b41.4 Drive Healthy. If =1 no alarms are present, otherwise =0.
b41.5 Hardware enable status . 1 when hardware enable is set.

37
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

b41.6 Temperature pre-alarm. 10 degrees before reaching the maximum temperature of the
power stage, b41.6 is set to 1.
b41.7 External alarm. Alarm for user’s equipment.
b41.8 Auxiliary alarm. Second alarm for user’s equipment.
b41.9 Calibration failed. b41.9=1 indicates that initial calibration of current offsets has
terminated incorrectly.
b41.10 Speed control saturation. b41.10=1 when the speed control loop is delivering maximum
current.
b41.11 I2T active. Indicates that Pr36 has reached 100.0 % and therefore the drive is restricting
current to the rated value.
b41.12 Drive enabled.
b41.13 Keypad fault. b41.12=1 if communication between keypad and drive has failed.
b41.14 External operating mode. If set to 1 an external operating mode is installed.
b41.15 External operating mode time slot. If set to 1 indicates that the external operating mode
is controlled at 2 ms intervals otherwise at 512µs.

b42.0 Selector to configure encoder emulation.


b42.1 Selector to configure encoder emulation.
b42.2 Selector to configure encoder emulation.

Pr32 up to 9000 rpm ================


Pr32 up to 3500 rpm ==========================
Pr32 up to 875 rpm =====================================
ENCODER OUT 16384 8192 4096 2048 1024 512 256 128
b42.0 0 1 0 1 0 1 0 1
b42.1 0 0 1 1 0 0 1 1
b42.2 0 0 0 0 1 1 1 1
the double line indicates encoder resolutions available in the various speed ranges
Default value is 1024

b42.4 24V over current. Digital output trip.


b42.5 Frequency input (board X6). If set to 1 the frequency input is programmed to receive two
phases in quadrature. This is the default. If set to 0 it is enabled to receive a
frequency/direction type input.
b42.6 Torque compensation. Default=1. When set to 1 torque compensation is implemented to
improve linearity of response.
b42.7 Reserved.

b99.6 Extended menu enable. Default=0. Set to 1 to enable the extended menu.
b99.7 Security. Default=0. Set to 1 to prevent parameter modification.
b99.13 pico-PLC status. Default=1. If on 1 the PLC program is run, if on zero the program is not
run and the PLC instructions can be modified if required.

38
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

3.4 Basic commands

To transmit the following commands b99.7 must be on zero. For commands b42.3 and b94.1,
b99.6 must be on one.

b42.3 Re-initialise serial line. Command to reinitialise the serial line when the communication
speed (Pr26) has been modified. In any event, the serial line is initialised when the drive is
started up.
b94.1 Reset main reference offset. This command automatically sets parameter Pr1 in order
to reset any voltage offset on the main analogue reference. This procedure is only possible
if the absolute offset value is less than 200 mV.
b99.9 Current offset calibration request. The command is accepted only if the drive is
disabled. The calibration procedure is executed when the drive is started up.
b99.10 Alarm reset. This command resets Pr23 and Pr24; if the alarm persists it is shown on the
display. The command is not accepted in the presence of checksum errors (Pr23=10, 11);
in this case set default parameters (b99.12) and then reset the alarm.
If the backup power supply is present (terminals 8 and 9 on X3), when mains power is
restored to the terminals on X4 you must wait 10 seconds before transmitting the
undervoltage alarm reset command and enabling the drive.
b99.11 Operating mode parameter default values. This command sets current operating
parameters to default values. The command is executed only if b40.2 = 0.
b99.12 Default values. This command sets all parameters to default values and cancels the values
used by the operating modes; it also sets the pico-PLC program as described in appendix
G. If a checksum alarm is present, Pr23 and Pr24 are set to zero so that the alarm can be
reset. The command is executed only if b99.13 = 0.
b99.14 Save pico-PLC instructions. Saves the pico-PLC program. If an error occurs while
saving, “retry” is shown on display: in this case transmit the command again.
b99.15 Save parameters. Stores all parameters. This command is not possible in the presence of
a checksum error; in this case, set default parameters, reset the alarm and then save the
new parameterisation settings. If an error occurs while saving, “retry” is shown on display:
in this case transmit the command again.

39
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

3.5 Calibrating speed loop

IMPORTANT CONCEPTS

SPEED LOOP: the main task of any drive is to control motor speed so that it follows, as faithfully
as possible, the required speed, which is generally referred to as the REFERENCE. High fidelity
reproduction of the reference implies that motor speed is identical to reference speed in static
conditions and also that it follows speed requirements closely also in the case of sudden changes in
the speed reference (dynamic conditions). To perform this task the drive must be informed of various
characteristics of the motor and the mechanical system to which the motor is coupled; this type of
information is set in the CALIBRATION PARAMETERS.
ERROR: the error refers to the difference between reference speed and motor speed. The error
value is utilised by the speed control loop to calculate (using calibration parameters) how much
current to supply to the motor.
TORQUE: current flowing through the motor windings is converted into torque which allows the
motor to accelerate and decelerate.
GAIN: in consideration of the typical applications of the HPD drive, the expression “gain” in this
section of the manual refers to “stiffness”. To understand the concept of stiffness imagine a motor
controlled by a drive with speed demand of zero rpm. The motor shaft will appear immobile but if
we apply torque to the shaft it will rotate through an angle that depends on the amount of torque
applied. We can then apply the rated torque of the motor and then measure the “stiffness angle” in
degrees. The resulting value provides an indication of the fidelity of the drive thus parametrised,
although it is clearly not the only fidelity indicator.

WHAT’S NEEDED

To calibrate an HPD drive correctly we recommend using an oscilloscope with memory.


Obviously, the technician in charge must be well versed in the use of the instrument. If it is impossible
to use an oscilloscope, we illustrate, at the end of this section of the manual, an alternative although
less accurate method.

40
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

BEFORE STARTING

Before starting observe figure 1.

Fig. 1

The graph shows system response to a square wave speed reference. Channel 1 (Ch1) is speed
and channel 2 (Ch2) is motor current. The channel 1 oscilloscope probe is connected to terminal 9
of X2 and channel 2 to terminal 7 of X2. The V/div scale and the timebase are not mentioned as
they may vary considerably.

CALCULATING Pr16

The value of Pr16 should be calculated before enabling the drive. Pr16 defines system gain. To
convert Pr16 into degrees for rated torque use the formula: a c = Pr 3 3 ⋅ 2 8 where ac is the stiffness
Pr 1 6
angle. Obviously, before the formula can be used Pr33 must be set to motor rated current. To
evaluate ac correctly we shall consider that, if the driven machine transmission is rigid (not flexible)
and there is no transmission backlash, the optimal stiffness angle could be around 4 degrees. If the
transmission is not sufficiently rigid it may be necessary to reduce gain. If motor torque has been
selected to achieve steep acceleration ramps, while dynamic torque changes in normal operation are
minimal, stiffness angles of 20, 30 or 40 degrees are acceptable without negatively affecting
performance. If you encounter difficulty in choosing the most appropriate stiffness angle, start from
10 degrees, which is the default value when using a motor with the same rated current as the drive.
Now enter the calculated value for Pr16 and start the motor with a square wave reference signal
(pay attention when setting the reference amplitude and frequency to avoid problems in the case of
limited stroke axes). On the oscilloscope note that the response changes as Pr17 is altered.
Lowering Pr17 will allow you to approach system response as shown in figure 2.

41
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Fig.2

For higher values of Pr17 system response will resemble the situation of figure 3 below.

Fig.3

The optimal value of Pr17 can be considered when system response is as shown in figure 4.

42
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Fig.4

We must therefore obtain approximately 10% overshoot. Make sure that the overshoot is not
followed immediately by undershoot.
Once you have set the optimal value for Pr17 pay attention to the movement of the motor shaft: if
it moves smoothly without vibration and noise, you can deduce that system calibration procedures
are terminated. Otherwise repeat all the previous steps using lower values for Pr16.
In certain applications you can reduce system acoustic noise levels by raising parameter Pr18 by
a few points. Fig.5 shows that the optimal system response is accompanied by a current fluctuation
that can generate acoustic noise and mechanical vibration; increasing Pr18 to the value 3 will improve
this condition significantly (fig. 6).

Fig.5

43
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Fig.6

If the driven mechanical system is prone to oscillation, we recommend using very low values for
Pr16; in this configuration the HPD drive will smooth out motor torque requests to prevent the
creation of mechanical oscillation. Figure 7 shows this type of configuration.

Fig.7

44
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

CALIBRATION WITHOUT INSTRUMENTS

If an oscilloscope is not available, proceed as follows:

A) Calculate the value of Pr16 as described earlier.


B) Calculate Pr17 using the following formula:

135.41 ⋅ Pr16 ⋅ J tot


Pr17 = 1488 ⋅
Nm peak
where: Jtot is total inertia (motor + load) in kgm2
Nmpeak is available torque with peak current of the system

C) Start the drive and, moving the axis with an external control change Pr17 to seek the value at
which the axis moves as required.
D) Calculate Pr18 using the following formula:
Pr 17
Pr 18 = 017
. ⋅ ≥1
Pr 16
If the resulting calibration is unsatisfactory, repeat the procedure with lower values for Pr16.

45
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

3.6 Operating modes

Operating modes are selected by means of parameter Pr31, whose default value is 0. Each
operating mode commands a speed loop by means of parameter Pr6 and can limit motor torque with
parameter Pr21 (see block diagrams). Speed control uses Pr7 or Pr6 as a reference depending on
the value of b40.2. Before changing Pr31, b40.2 must be set to 0 to prevent undesired motor
movement; it is now possible to set Pr31 to the value of the chosen operating mode and load default
parameters by means of parameter b99.11. The operating mode will be enabled by setting b40.2 to
1.

3.6.1 Torque control

This operating mode (1) does not perform “classic” torque control because the speed loop
remains active to monitor limit speed; the torque reference is the main reference Pr7. To set torque
control first program the speed loop to create a stable system. Now set Pr2=1000 (10 V = 100.0 %
torque) b40.0=0 & b40.12=0; b40.2=1 to program the reserved reference, Pr31=1 to enable the
operating mode and Pr50 for maximum speed.

PARAMETERS FOR OPERATING MODE 1

Pr50 Maximum speed. Unit=rpm, default=3000, range=0..9000. This parameter makes it


possible to limit maximum absolute motor speed during torque control operation.

3.6.2 Acceleration control

Instead of performing closed loop acceleration control, this mode (2) uses main reference Pr7 for
dynamic modulation of the ramps. To program analogue acceleration control the first requirement is
a stable speed loop. When this is present set Pr2=ACC / 3.2 where ACC is acceleration in rad/s2
required with a 10V reference signal, b40.0 = 0, b40.12 = 0, b40.2 = 1 and Pr31 = 2. Maximum
speed must be programmed in Pr50.

PARAMETERS FOR OPERATING MODE 2

Pr50 Maximum speed. Unit=rpm, default=3000, range=0..9000. This parameter makes it


possible to limit maximum absolute motor speed during operation with acceleration
reference.
Pr55 Acceleration/deceleration ramp, read-only parameter. Unit=s/krpm, range=2..30000,
resolution=1 thousandth of a second.
Pr60:61 Reserved.
Pr62:63 Reserved.
Pr66:67 Reserved.

46
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

3.6.3 Maintenance and commissioning

This operating mode is designed to assist technical personnel during commissioning.


Mode 8 provides various tests to check drive wiring. It’s also possible to move the move the
shaft manually by means of Pr50, b70.1 and b70.2 or using the internal profile generator, which
simplifies speed control loop set-up and ensures that there is no overrun on the programmed
movement. Programming parameters for generating internal profiles are: speed, motor revolutions,
starting position and interval, in seconds, between forward and reverse movement.
To perform the wiring test the motor must be disconnected from all loads, including inertia loads;
disable the drive via software (b40.9=0), Pr30 must be zero, enable the drive via hardware and set
b70.3=1. The drive will now execute the test routine. When terminated (b70.3=0), the error code in
Pr56 can be displayed after setting Pr57=0.
Error codes:
0 no error
1 b40.9=1 or drive disabled via hardware
2 motor phase sequence and resolver direction incompatible
3 number of motor poles and Pr29 incompatible
4 resolver phase error
5 Pr30 value not zero
99 procedure aborted
By setting the various values in Pr57 you can get other useful information for installation and
maintenance (see table in block diagrams).

PARAMETERS FOR OPERATING MODE 8

Pr50 Manual speed. Unit=rpm, default=100. This speed value is used for manual movements
executed using b70.1 , b70.2 with b70.0=0 and b40.2=1.
Pr51 Profile execution speed. Unit=rpm, default=1000. This is the speed at which the
trapezoidal profile is executed.
Pr52 Distance. Unit=revolutions, default=30. This is the number of revolutions of the motor
shaft that must be performed during generation of the profile.
Pr53 Starting point. Default=1. If set to 1, at start profile (b70.0) the motor will start rotating
and execute Pr52 revolutions with positive speed. If set to 2 the motor will start rotating
and execute Pr52 / 2 revolutions with positive speed. If you set 3 the motor will start and
execute Pr52 revolutions at negative speed.
Pr54 Pause. Unit= tenths of a second, default=1. During execution of the profile the drive stops
between positive speed movement and negative speed movement for an interval of Pr54 at
zero rpm.
Pr55 Deviation factor. During execution of the profile, assuming the same value of Pr16 the
optimal value of Pr17 can be achieved by minimising the value of Pr55.
Pr56 Value. Returns information requested with Pr57.
Pr57 Information request. This parameter serves to query the drive. A table of queries is
shown in the block diagram of operating mode 8.
Pr58 Reserved.
Pr59 Reserved.
Pr60:61 Reserved.
Pr62:63 Reserved.
Pr64:65 Reserved.

47
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Pr66:67 Reserved.
Pr68:69 Reserved.
b70.0 Start profile. Set 1 to execute the programmed profile. Remember to set b40.2=1 to
effectively switch the speed reference to the control loop.
b70.1 Manual forward speed. If at 1 with b70.0=0 and b40.2=1, the shaft will rotate at the
speed programmed in Pr50.
b70.2 Manual reverse speed. If at 1 with b70.0=0 and b40.2=1, the shaft will rotate at the
speed programmed in Pr50 but in the opposite direction.
b70.3 Wiring test. When you set this command the drive performs a test procedure and returns
the result as an error code that can be viewed using parameters Pr56 and Pr57. Before
entering this command, make sure the motor is disconnected from all loads, even pure
inertia loads. Also ensure that b40.9=0.
b70.4 Reserved.
b70.5 Vibration test. If none of the above functions is active, you can set this bit to one to
evaluate the vibration of the motor shaft, incrementing parameter Pr64 in absolute terms by
a value proportional to the vibration detected. The user is responsible for evaluating Pr64
and bringing it to zero in relation to the appropriate time interval.
b70.6 Reserved.
b70.7 Reserved.
b70.8 Reserved.

3.6.4 Positioner

Operating mode 9 executes a simple trapezoidal profile. For this profile the user must define
acceleration with Pr51, steady time rpm with Pr52 and displacement using the pair of long format
parameters Pr64 and Pr65. At each profile execution command, b70.8, the motor executes Pr64:65
steps (one motor revolution is equivalent to 4096 steps). The parameters of a trapezoidal profile
cannot be changed during execution (b70.7=1), except Pr64:65. In the block diagram note the four
different reset types, the availability of servo-error indication and the possibility of using space
control with or without feed forward. The incremental position must be always positive and
movement direction must be selected with parameter b70.1. Displacement can be defined using the
drive frequency input. Additional features are available using the internal PLC.
Note that the profile execution command is not generated on a constant time base (profile
calculation may require more than 2 milliseconds).

PARAMETERS FOR OPERATING MODE 9

Pr50 Pulse input multiplication factor K. Default=1. If b70.9=1 frequency/direction input


pulses are multiplied by Pr50 and the result is added to Pr64:65. The frequency input
direction signal must be forced to a fixed level (logical 0). Refer to the chapter Frequency
input connection for the connection diagrams.
Pr51 Acceleration time . Unit=s/krpm, range=0.002..30.000, resolution=0.001 sec,
default=0.002 S. Acceleration ramp for positioning profile.
Pr52 Rpm at speed. Unit=rpm, default=1000. Steady state speed used during generation of the
positioning profile.
Pr53 Reserved.
Pr54 Reserved.

48
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Pr55 Reserved.
Pr56 Servo-error window. Unit=steps, default=100. If the position error as an absolute value
exceeds the value set in Pr56, b70.5 is set to 1. If b70.5 is utilised it must be reset by the
user following servo errors. This can be achieved, for example, by the PLC program.
Pr57 Position controller proportional gain. Default=100, range 0..32000.
Pr58 Reserved.
Pr59 Reserved.
Pr60:61 Position controller reference. Unit=steps.
Pr62:63 Motor position. Unit=steps, 4096 steps per revolution.
Pr64:65 Incremental position. Unit=steps. On receipt of the profile request, b70.8, the motor will
execute Pr64:65 steps in the direction set in b70.4.
Pr66:67 Reserved. Cannot be used during profile generation.
Pr68:69 Reserved. Cannot be used during profile generation.
b70.2 Reset incremental position. Resets Pr64:65. This command is useful when the
incremental value is programmed on the frequency input.
b70.4 Forward/Reverse. When the start profile command is transmitted (b70.8) if b70.4=0 the
motor will execute Pr64:65 steps in the positive speed direction. If b70.4=1 it will execute
the same number of steps in the negative speed direction.
b70.5 Servo error. b70.5 is set to 1 if the absolute value of the position error is greater than the
value set in Pr56. If utilised, b70.5 must be reset by the user, e.g. using the PLC program,
following servo-errors.
b70.6 Feed-forward enable. Default=0. If set to 1 feed-forward is enabled on the position
controller.
b70.7 Profile in execution. B70.7=1 indicates that the drive is executing a positioning profile.
b70.8 Start profile. To start positioning.
b70.9 Enable frequency input. Default=0. If set to 1, Pr64:65 can be set on the frequency
input.
b70.10 Reset type 1. Resets motor and reference position. This command is only accepted when
no profile is in execution.
b70.11 Reset type 2. Command to set motor and reference position to equal the absolute
position of the shaft. Accepted only when no profile is in execution.
b70.12 Reset type 3. Command to set the reference equal to the motor position. Accepted only
when no profile is in execution.
b70.13 Reserved.
b70.14 Reserved.
b70.15 Reserved.

3.6.5 Digital locking

Operating mode 10 is a tracking function referred to a frequency input signal (connector X6) set
as an encoder signal with b42.5=1; the encoder signal is counted on all A and B signal switching
fronts. The motor position counter increases by 4096 steps each revolution. The ratio between
master and slave can be entered using parameters Pr51 and Pr53. You can also select the ramp to
utilise during catch or release cycles (Pr52), add slip speed (Pr58) and limit speed demands of the
proportional part of the loop (Pr50). Further information available: master and slave locked and
servo-error. Using Pr52, the main ramps and the internal PLC makes it possible to program various

49
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

different catch and release modes with or without phase recuperation. Refer to Frequency input
connection chapter for connection diagrams.

PARAMETERS FOR OPERATING MODE 10

Pr50 Maximum speed. Unit=rpm, default=200, range =0..9000. This parameter makes it
possible to limit maximum speed of the motor; it can be used to limit speed during a catch
on fly cycle or during sudden speed changes (see Pr58).
Pr51 Reference multiplication factor. Default=1, range =-32000..+32000. This parameter,
together with Pr53, makes it possible to set the required ratio for the input reference
frequency.
Pr52 Acceleration/deceleration ramp. Unit=s/krpm, default=500, range=0..30000,
resolution=1 thousandth of a second. The acceleration/deceleration demanded of the motor
can be restricted so that a speed decrease or increase of 1000 rpm takes Pr52 thousandths
of a second; this function is useful during catch on fly cycles.
Pr53 Reference division factor. Default=1, range=-32000..+32000. This parameter together
with Pr51 makes it possible to set the required ratio for the input reference frequency.
Pr54 Reserved.
Pr55 Required speed. Unit=rpm Read-only parameter. Shows the input reference frequency
converted into rpm
Pr56 Servo-error window. Unit=steps, default=100. If the absolute value of the position error
exceeds the value set in Pr56, b70.5 is set to 1. If utilised, b70.5 must be reset by the user,
e.g. by the PLC program, following servo-errors.
Pr57 Position controller proportional gain. Default=100, range 0..32000.
Pr58 Slip speed.
Pr59 Reserved.
Pr60:61 Position controller reference. Unit=steps.
Pr62:63 Motor position. Unit=steps, 4096 steps per revolution.
Pr64:65 Reserved.
Pr66:67 Reserved.
Pr68:69 Reserved.
b70.2 Digital locking engaged. During locking with ramp (Pr52) other than zero, this bit
indicates the termination of the transitional phase.
b70.3 Enable position. Default=0. During unlocking b70.3=1 enable position with Pr61:60.
b70.5 Servo-error. b70.5 is set to 1 if the absolute value of the position error exceeds the value
set in. If utilised, b70.5 must be reset by the user, e.g. by the PLC program, following
servo-errors.
b70.6 Feed-forward. Default=1. If set to 1 feed-forward is enabled on the position controller.
b70.8 Axis lock/release. With this bit you can lock (=1) or release (=0) the axis from the input
encoder reference.
b70.9 Reserved.
b70.10 Reset type 1. Resets motor and reference position. Implemented only with b70.8=0.
b70.15 Reserved.

50
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

3.6.6 Stepper motor emulation

This mode emulates the operation of a stepper motor: each pulse received on the frequency input
(terminal board X6 channel A=frequency, channel B=direction) is multiplied by Pr51 and the result is
added to the reference position. The frequency input must be programmed as a direction/sign signal
by setting b42.5=0. Just as in all other operating modes it is possible to enable feed forward, limit the
action of the proportional part, obtain servo-error indication and select the most suitable type of
reset. Note that the frequency count occurs on the negative front of the signal and changes of the
direction signal must be made at least 1 µS before the negative frequency front. Unlike stepper
motors, in this case there is no risk of step loss. Refer to Frequency input connection chapter for
the connection diagrams.

PARAMETERS FOR OPERATING MODE 11

Pr50 Maximum speed. Unit=rpm, default=3000, range=0..9000. This parameter makes it


possible to limit maximum motor speed.
Pr51 Reference multiplication factor. Default=1, range=-0..+4096. This parameter allows
you to set the required multiplication ratio for input reference frequency.
Pr54 Reserved.
Pr56 Servo-error window. Unit=steps, default=100. If the absolute position error is greater
than the value in Pr56, b70.5 is set to 1. If utilised, b70.5 must be reset by the user, e.g. by
the PLC program, following servo-errors.
Pr57 Position control loop proportional gain. Default=100, range 0..32000.
Pr60:61 Position control loop reference. Unit=steps.
Pr62:63 Motor position. Unit=steps, 4096 steps per revolution.
Pr64:65 Reserved.
b70.5 Servo-error. b70.5 is set to 1 if the absolute position error is greater than the value in
Pr56. If utilised, b70.5 must be reset by the user, e.g. by the PLC program, following
servo-errors.
b70.6 Feed-forward enable. Default=0. If set to 1 feed-forward is enabled on the position
controller.
b70.8 Axis lock/release. With this bit you can lock (=1) or release (=0) the axis from the input
encoder reference.
b70.9 Reserved.
b70.10 Reset type 1. This command resets motor and reference position.
b70.11 Reset type 2. Sets motor and reference position equal to the absolute shaft position.
b70.12 Reset type 3. Sets the reference equal to the motor position.

51
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

3.6.7 Spindle orientation

When this mode (12) is selected it becomes operational when b40.2=1. The motor reaches the
speed in Pr50 on the ramps in Pr52. It now spins at constant speed until it reaches the position set in
Pr54; at this point the position loop is closed.

PARAMETERS FOR OPERATING MODE 12

Pr50 Maximum speed during spindle orientation. Unit=rpm, default=200, range=0..500.


This parameter makes it possible to limit maximum motor speed during spindle orientation.
Pr51 Reserved.
Pr52 Deceleration ramp. Unit=s/krpm, default=500, range=2..30000, resolution=1 thousandth
of a second. When the spindle orientation command is set (b40.2=1) deceleration required
of the motor can be limited by this parameter so that a change of 1000 rpm takes Pr52
thousandths of a second.
Pr53 Reserved.
Pr54 Motor shaft position for spindle orientation. Unit=steps, default=0, range=0..4095.
One revolution of the motor shaft corresponds to 4096 steps.
Pr56 Servo-error window. Unit=steps, default=100. If the absolute position error is greater
than the value set in Pr56, b70.5 is set to 1.
Pr57 Position control loop proportional gain. Default=100, range = 0..32000.
Pr58 Reserved.
Pr59 Reserved.
b70.5 Servo-error. b70.5 is set to 1 if the absolute position error is greater than the value in
Pr56, otherwise it is set to zero.

3.7 Block diagrams

The main block diagram provides a graphic description of how to use the drive. Each rectangular
block represents one or more read/write parameters, each rhomboid shape represents read-only
parameters. In the diagram there are other functional blocks such as: greater than..., equal to, the
smallest among..., logical and/or; we have used standard symbols for all these blocks. Binary
parameters are shown as switches and the position depicted is the default value.

52
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Pr X
A
• Read/write parameter PrX
A = value of PrX
A B • Read/write parameter PrX
Pr X
B = value according to values of A and PrX
A • Read-only parameter
Pr X PrX is value of A (can also be binary)
• Read/write bit parameter
bx.y
switch position shows bx.y=0

bx.y
• Value of bit parameter bx.y sets the switch

• If A is smaller than B, C =1 (true); otherwise C = 0 (false)


A B

A
B
C G
D • The value of G is the lower value among A B C D E and F
E
F

A
C
B

• C = 1 only when A = 1 and B = 1; otherwise C = 0

A
C
B
• If A or B are 1, C = 1
otherwise C = 0

A + C

• C=A- B
-
B

• values from hardware

• values to hardware

A B
• Value of A is converted to B. E.g., if the triangle symbol contains A/D,
the analogue value of A is converted into the digital value B
A

• Maximum value of A is PrX

Pr X

53
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

left-sw b40.4
offset

Pr 1 full scale main ref.


right-sw b40.5
HIGH PERFORMANCE DRIVE
ref. 1

+
- Pr 2 b40.0
Pr 7
stop b40.6
MAIN BLOCK DIAGRAM
A/D
torque demand
ramps values
Pr 3
band-width
S/H Pr 35
full scale Pr 8 speed control limitator
b40.12
ref. 2 Pr 9
b40.2 b40.3 torque
Pr 10 + Pr 16
max fq ref. Pr 18
Pr 11 Pr 17 demand
F/D -
Pr 4
user current limit
internal reference ramp b40.11
Pr 12 Pr 19
value analog out
b40.7
Pr 5 b40.13 Pr 0
thermal image limit
reserved reference
motor speed
b41.11
Pr 6 Pr 38
-
+ Pr 33
Vout aux
rated current
over reserved current limit
Param. DESCRIPTION R/W
over speed
Pr 13
Pr 21
Pr 25 SOFTWARE RELEASE N
b 41.0
Pr 26 BAUD RATE Y max
high
Pr 27 SERIAL LINK ADDRESS Y
Pr 14 b40.8
Pr 28 SHAFT POSITION N
at speed
Pr 29 MOTOR POLES Y
Pr 30 RES. PHASE SHIFT Y b 41.1 Pr 22 trip code
Pr 31 OPERATING MODE Y present last
low aux reference drive enabled
Pr 32 RATED SPEED Y
Pr 15 Pr 23 Pr 24
Pr 36 I2T ACCUMOLATOR N b41.12
over voltage
Pr 37 BRAKE RESISTOR USE N
drive ok
under voltage
Pr 20 DC BUS VOLTAGE N
over current
Pr 39 PHASE ADVANCE Y b41.4
zero speed
resolver break
Pr 34 GAIN FOR TACHO
motor over temp. hardware
B42.0 b 41.2
enable
power stage over temp
B42.1 ENCODER OUT RESOL. Y
b 41.7 external trip
B42.2 forward b41.5
aux. trip
B42.5 QUADRATURE / FD Y
b 41.3 output short circuit
B41.14 EXTERNAL OPM N b 41.8 software
PLC check-sum enable
B41.15 FLAGS
PAR. check-sum
B41.6 PRE ALARM N b40.9
B40.1 VIBRATION STOP. Y
B40.10 LOW VOLTAGE OP. Y

54
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

REFERENCE SELECTION
offset

Pr 1 full scale main ref.


ref. 1

Pr 7
- Pr 2 b40.0
+
A/D
ramps values
Pr 3
S/H
full scale Pr 8
b40.12
ref. 2 Pr 9
b40.2 b40.3
Pr 10
max fq ref.
Pr 11
F/D Pr 4

internal reference

Pr 5 b40.13

reserved reference

Pr 6

1 TORQUE CONTROL
OPERATING MODE

Pr 50 Pr 6
max speed
-1 reserved reference

Pr 7

main ref
1

Pr 21

reserved
-1
current limit

55
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

2 ACCELERATION CONTROL
OPERATING MODE

ramps
1

Pr 50 Pr 55 Pr 6
max speed
-1 reserved reference

Pr 7

main ref
1

-1

8 MAINTENANCE & COMMISSIONING


manual speed
1

OPERATING MODE
b70.1

Pr 50
-1
b70.2

profile generator

T
Pr 6
V
reserved
reference
wiring test selector pos.
A
b70.3 Pr 57

0
b70.0 error code
1
1 2 3 # motor poles
start/stop 2
resolver phase
3 value
reference input
4
Pr 55 Pr 51 Pr 52 Pr 53 Pr 54 aux analog input 5 Pr 56
digital input status 1
6
err. std dev. test speed test stroke starting point delay
digital input status 2 7
encoder in counter
8
bus voltage
9
offset compensation U
10
offset compensation V

56
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

TRAPEZOIDAL POSITIONER
9 OPERATING MODE
in progress

b70.6
b70.7

profile generator
feed
Pr 56
forward
servo error
V b70.5
window
servo error -1
IQ
A
proportional reserved
gain
+ reference

Pr 61:Pr60
+ Pr 57
+ Pr 6
Pr 51 Pr 52 -
ramps steady time target position
speed

b70.8
Pr 63:Pr62
profile on reset 1
reverse/forward
motor position b70.10 target position = motor position = 0
b70.4

pulses b70.11 target position = motor position = shaft position


Pr 65:Pr 64 Pr 50 reset 2
b70.9

incremental
steps for pulse
position b70.12 target position = motor position
reset 3

b70.2 incremental position Pr 65:Pr 64 = 0


reset 4

DIGITAL LOCK
10 OPERATING MODE
master speed

Pr 55 b70.2
ratio
encoder locked
master
d Pr 51 b70.6
Pr 52
dt b70.8
Pr 53
ramp feed
forward

proportional

+
gain
+
Pr 61:Pr60
+ Pr 57
+ Pr 6

+ target position
- reserved reference

Pr 58
Pr 50
slip
Pr 63:Pr62
speed max regulator
speed
motor position

reset 1 Pr 56
servo error
b70.10 target position = motor position = 0 b70.5
window
servo error -1

57
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

STEPPER LIKE
11 OPERATING MODE
feed forward
d
dt b70.6

Pr 56
servo error
b70.5
window
servo error -1
k mul
pulses input
Pr 51 proportional
gain
+
Pr 61:Pr60
+ Pr 57
+ Pr 6
- reserved reference
target position

Pr 50
Pr 63:Pr62
max regulator
speed
motor position
reset 1

b70.10 target position = motor position = 0

b70.11 target position = motor position = shaft position


reset 2

b70.12 target position = motor position


reset 3

SPINDLE ORIENTATION
OPERATING MODE
12
Pr 56
oriented
b70.5 window
not oriented -1

proportional
gain

Pr 54
+ Pr 57

target position
- Pr 6

reserved reference
max regulator
Pr 50 Pr 52
speed
Pr 28
ramps

shaft position
motor
speed Pr 0

58
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

3.8 Digital input and output programming

3.8.1 Pico-PLC

The internal pico-PLC makes it possible to connect peripheral systems (inputs/outputs) to the
parametric system of the HPD drive. The PLC can be used to copy a digital input into a bit
parameter, copy a bit parameter into a digital output and perform mathematical and boolean
calculations. The PLC program must be entered as a list of instructions from the keypad; alternatively
the PLC can be programmed with the ladder diagram system using a PC on the serial line with an
interface such as Pcbrush. Default parameterisation (b99.12) provides a PLC program (see
appendix G) designed to fill the requirements of the broadest possible range of applications,
therefore it is not necessary to reprogram the PLC in the majority of cases.
Main features of the PLC:

Program steps 64
scan time 6.144 ms
timers 2
instructions 15
stack depth 1
mathematic operations 16 / 32 bits
fast inputs (fast copy) 3 - (512 µ s)

PLC PARAMETERS

Pr71 Constant value = -1. Double word.


Pr72 Constant value = 0. Double word.
Pr73 Constant value = 1. Double word.
Pr74 Constant value = 2. Double word.
Pr75 Constant value = 10. Double word.
Pr76 Constant value = 100. Double word.
Pr77 Constant value = 1000. Double word.
Pr78 Constant value = 1024. Double word.
Pr79 Constant value = 4096. Double word.
Pr80 Free parameter. Parameter with save facility at user’s disposal (word).
Pr81 Free parameter. Parameter with save facility at user’s disposal (word).
Pr82 Free parameter. Parameter with save facility at user’s disposal (word).
Pr83 Free parameter. Parameter with save facility at user’s disposal (word).
Pr84 Free parameter. Parameter with save facility at user’s disposal (word).
Pr85 Free parameter. Parameter with save facility at user’s disposal (word).
Pr86 Free parameter. Parameter with save facility at user’s disposal (word).
Pr87 Free parameter. Parameter with save facility at user’s disposal (word).
Pr88 Free parameter. Parameter with save facility at user’s disposal (word).
Pr89 Free parameter. Parameter with save facility at user’s disposal (word).
b90.X Digital input X status . If X is greater than 7, parameter with save facility at user’s
disposal (b90.0 = drive enable).
b91.Y Digital input Y status. If Y is greater than 7, parameter with save facility at user’s
disposal. Parameter Pb91 is not saved at power up and is definitely at zero.

59
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Pr92 First PLC timer. Every 6.144 ms if Pr92 is not at 0 the timer is decreased, if set to zero
b99.0 is set at 1.
Pr93 Second PLC timer. Every 6.144 ms if Pr93 is not at 0 the timer is decreased, if set to
zero b99.1 is set to 1.
b94.0 Forces a double word formatted operation. When the drive is powered up this
parameter is on zero. If it is on one, the first mathematical operation of the pico-PLC is
executed setting the three operands as double word type; after the operation is executed
b94.0 is automatically set to zero.
If Pr60..Pr68 are utilised, double word formatting is automatic (see text).
b94.5 Disables the first fast input (b94.5=0). Set to zero at power-up.
b94.6 Disables the second fast input (b94.6=0). Set to zero at power-up.
b94.7 Disables the third fast input (b94.7=0). Set to zero at power-up.
b99.0 First timer status. At 1 if Pr92 = 0
b99.1 Second timer status. At 1 if Pr93 = 0
b99.2 At 1 if the result of the last PLC operation is negative.
b99.3 At 1 if the result of the last PLC operation is zero.
b99.13 PLC status. Default=1. If set to 1 the PLC program is executed, if on zero the program is
not executed and modification of PLC instructions is enabled.

PLC INSTRUCTIONS
Pa.y

LD Pa.y load bit y of parameter Pa in the stack


Pa.y

LDN Pa,y load inverted bit y of parameter Pa in the stack


Pa.y

OUT Pa,y set bit y of parameter Pa to the value loaded in the stack
Pa.y

Pa.y
OUTN Pa,y set bit y of parameter Pa to the stack value and invert it
SET

Pa.y
SET Pa,y if stack is at 1, set bit y of parameter Pa to 1
RST RES Pa,y if stack is at 1, set bit y of parameter Pa to zero
Pa.y AND Pa,y the bit loaded into the stack assumes the result of the logical
AND operation between itself and bit y of parameter Pa
Pa.y ANDN Pa,y the stack bit assumes the result of the logical AND between
itself and inverted bit y of parameter Pa
Pa.y
OR Pa,y the bit loaded into the stack assumes the result of the OR
between itself and bit y of parameter Pa
Pa.y
ORN Pa,y the stack bit assumes the result of the OR between itself and
inverted bit y of parameter Pa
Pa Pb Pc
ADD Pa, Pb, Pc if stack bit is at 1, parameter sum operation is executed,
ADD

Pa Pb Pc
therefore: Pc = Pa + Pb
SUB
SUB Pa, Pb, Pc if stack bit is at 1, subtraction operation is executed on
Pa Pb Pc
parameters, therefore: Pc = Pa - Pb
MUL MUL Pa, Pb, Pc if stack bit is at 1, multiplication operation is executed on
Pa Pb Pc parameters, therefore: Pc = Pa ⋅ Pb
DIV DIV Pa, Pb, Pc if stack bit is at 1, division operation is executed on the
END
parameters, therefore: Pc = Pa / Pb
Pa.y
END program end
FIN

FIN y, 0/1 fast scanning input


60
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

OPERATIONAL DESCRIPTION

The pico-PLC program is scanned every 6.144 msec; at each sampling first the inputs are read,
then the two timers are updated (Pr92 Pr93 b99.0 and b99.1), the user program is scanned, and
finally the outputs are updated. Therefore, reading of the inputs and output updates can deviate
temporally by up to 6.144 ms with respect to the physical event.
All pico-PLC instructions with the exception of mathematical instructions, operate on single bits;
moreover, available stack depth is a single bit.
Instruction LD (LDN) loads the bit defined as operand into the stack, while all other logical
instructions operate on the stack. Mathematical operations are executed only if the stack bit is at 1.
The following logic operations truth tables are provided for the user’s convenience:

logical AND operations logical OR operations


bit A bit B result bit A bit B result
0 0 0 0 0 0
0 1 0 0 1 1
1 0 0 1 0 1
1 1 1 1 1 1

The relative inverted ANDN and ORN operations follow the same logic, except they use the
inverted value of the specified bit.
There are 8 bits with save facility from b90.8 to b90.15 reserved for the PLC; a further 8 bits
from b91.8 to b91.15 are available for the PLC; these are not stored and are always at zero at drive
power-up.
Also 10 word parameters are reserved, specifically from Pr80 to Pr89 with save facility and
option for use as 5 double word parameters. For mathematical operations the pico-PLC has 9
constants available, from Pr71 to Pr79 selected from those that are most frequently utilised in
standard applications.
When using mathematical instructions (ADD, SUB, MUL, DIV) note that operators are assumed
as words with their relative signs. If a double word operation is necessary, parameter b94.0 must be
set to 1 before the operation; after the operation the PLC will automatically set the bit to zero.
Parameters Pr60...Pr69 are considered as double words so an operation like [ADD 71 72 64] will
write the result -1 in the double word Pr64:65 without having to set b94.0=1 before the operation. If
Pr80=-1 and Pr81=0, the operation [ADD 80 72 64] will have the result Pr64:65=-1, while the
same operation performed with b94.0=1 will assume Pr81 as the high part of the double word
Pr80:81 so the result will be Pr64:65=65535. In the first case, therefore, operands other than
Pr60...Pr69 will be treated as words, while in the second case they will be treated as double words.
Note that in mathematical operations on double words, operands and results are defined as
follows: the operand parameter defines the least significant part while the most significant part is
represented by the word with the next serial address (see chapter Serial addresses and parameter
lengths). Parameters from Pr50 to Pr69 and from Pr80 to Pr89 are successive.
At the completion of each mathematical operation b99.2 is set to 0 if the result is positive, and to
1 if the result is negative; likewise, b99.3=0 if the result is zero and b99.3=1 if it is different from
zero. These settings remain valid until the next mathematical operation is performed (the operation is
executed only if the stack bit is equal to one). A mathematical operation can be performed, setting
the result in one of the constant parameters (Pr71...Pr79) in order to set bits b99.2 and b99.3.
In the case of the DIV operation, if it is executed on a double word the most significant part of the
result contains the rest of the division, i.e. if you set b94.0=1 and perform [DIV 79 77 80] the result
will be Pr80=4 and Pr81=96.

61
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Note that parameters Pr23, Pr24, Pr25, Pr26, Pr27, Pr29, Pr31 and Pr34 are bytes like Pb42
and Pb94; therefore, these parameters cannot be used for mathematical operations; logical
operations must be used to alter their values.

FIN instruction. Three instructions are provided for high speed input acquisition: in this case the
scan is executed at 512µs (normal scanning is 6.144ms). If used, FIN instructions must be the first
PLC instructions. The first FIN instruction copies digital input 1 into bit y of parameter Pb40 (second
operand=0) or Pb70 (second operand =1). The second FIN instruction copies digital input 2 into bit
y of parameter Pb40 (second operand=0) or Pb70 (second operand=1). The third FIN instruction
copies digital input 3 into bit y of parameter Pb40 (second operand=0) or Pb70 (second
operand=1). If the second operand is added to value 2, before the input is copied it will be inverted.
If a FIN instruction is included at any other position in the program it will have no effect. FIN
instructions can be enabled/disabled for each FIN: 1st FIN enabled if b94.5=0; 2nd FIN enabled if
b94.6=0; 3rd FIN enabled if b94.7=0.
A FIN instruction in the PLC program after the first three instructions or after any other type of
instruction will always be ignored.

There are two timers Pr92 and Pr93 at the disposal of the user. To use the first timer simply load
the time in terms of number of samplings (6.144 ms) in parameter Pr92: for example Pr92=100 is
equivalent to 614 milliseconds. Pr92 automatically decreases through time, bit b99.0 remains on zero
until the timer interval has elapsed; when Pr92=0 then b99.0=1. The same functionality applies to the
second timer regarding parameter Pr93 and bit b99.1. Ensure that Pr92 Pr93 b99.0 and b99.1 are
refreshed only after the first pico-PLC program scan.
The maximum number of instructions is 64 including the END instruction. Note that mathematical
operations occupy the space of two logical operations so when they are used the maximum number
of instructions available is decreased accordingly.
The PLC program must always be terminated with an END instruction.
The pico-PLC program can be edited on a PC (see Programming with Pcbrush) or directly
from the keypad. In this latter case, to facilitate procedures, when you need to delete an instruction,
select it and then press [M] to display the type of instruction; now keep [M] pressed and
simultaneously press [-]; when both keys are released the instruction will be deleted. On the
contrary, in order to add an instruction after In06 for example, select the next instruction In07, press
[M] to display the type of instruction; now keep [M] pressed and press [+] simultaneously; when
both keys are released an FIN instruction will be inserted. In this latter procedure make sure that the
instructions in the program are no more than the maximum number or you will lose the last one(s).
The pico-PLC program can be edited or altered only when the PLC is in stop status (b99.13=0).

62
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

3.8.2 Examples and applications

The following examples illustrate possible functionalities obtained by suitable programming of the
HPD pico-PLC. The suggested solutions offer the possibility of reducing the components required to
build the machine or part of the machine while, in many cases, also cutting the overall cost of the
application. Note that the pico-PLC scanning time is 6.144 msec and the maximum number of
instructions is 64; moreover, the PLC is designed principally to manage the drive’s digital inputs and
outputs.
In addition to a concise description of the application, the examples show the settings required for
HPD parameters and the pico-PLC program. The program is shown in ladder diagrams and
instruction listings.

Example 1: two inputs for on/off functions

90.1 90.2 91.2


LD 90.1 digital input 1 sets bit b91.2 to on
OR 91.2 digital input 2 sets bit b91.2 to off
91.2 ANDN 90.2
OUT 91.2

Example 2: changing a parameter value with the up/down keys


90.1 99.0 05 73 05
LD 09.1 digital input 1 in high status increases
ADD
AND 99.0 parameter Pr5 by one unit every 614
92 76 92 ADD 05.73.05 msec
ADD ADD 92.76.92
90.2 99.0 05 71 05
LD 90.2 digital input 2 in high status decreases
ADD AND 99.0 parameter Pr5 by one unit every 614
92 76 92 ADD 05.71.05 msec
ADD
ADD 92.76.92

Example 3: command on positive front of a digital input


90.1 90.10 70.8 LD 90.1 digital input 1 sets bit b70.8 just once
SET
ANDN 90.10 when the signal changes from low to
SET 70.8 high
90.1 90.10
LD 90.1
OUT 90.10

63
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Example 4: filtered digital input at 60 msec

90.1 90.10 72 75 92 LD 90.1 if digital input 1 is low, load 60 msec on


ADD ANDN 90.10 counter;
ADD 72,75,92 if digital input 1 is high for 60 msec
99.0
RST 99.0 b99.0 will be set to 1 and b90.11=1
RST

90.1 90.10 72 75 92

ADD
LDN 90.1 if digital input 1 is high, load 60 msec on
AND 90.10 counter
99.0
ADD 72,75,92 if digital input 1 is low for 60 msec,
RST RST 99.0 b99.0=1 and b90.11=0
90.1 90.10
LD 90.1
OUT 90.10
LD 90.1
90.1 99.0 90.11 AND 99.0
SET SET 90.11 b90.11 is the status of filtered digital
LDN 90.1 input 1
90.1 99.0 90.11
AND 99.0
RST RST 90.11

Example 5: correlation between parameter values

99.13 00 80 72
LD 99.13 calculate difference between Pr0 and
SUB SUB 0,80,72 Pr80 to set b99.2 and b99.3
99.3 81.0
LD 99.3
OUT 81.0 if Pr0=Pr80 then b81.0=1
99.2 81.1

LD 99.2
OUT 81.1 if Pr0<Pr80 then b81.1=1
99.3 81.2
LDN 99.3
OUT 81.2 if Pr0<>Pr80 then b81.2=1
99.2 99.3 81.3 LDN 99.2
ANDN 99.3 if Pr0>Pr80 then b81.3=1
OUT 81.3
99.2 81.4

LDN 99.2
OUT 81.4 if Pr0>=Pr80 then b81.4=1
99.3 81.5

LD 99.3
99.2 OR 99.2 if Pr0<=Pr80 then b81.5=1
OUT 81.5

64
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Example 6: filter (600 msec) for reading the value of a parameter

99.13 35 60 60

ADD
LD 99.13 Add Pr35 and Pr60
ADD 35,60,60
99.0 60 76 81

DIV LD 99.0 if timer 1 expired calculate filtered Pr35


60 60 60 DIV 60,76,81 setting result in Pr81
SUB
SUB 60,60,60 zero set Pr60
92 76 92

ADD ADD 92,76,92 reset time m 1 to 600 milliseconds


81.15 81 71 81
LD 81.15 if Pr81 is negative its sign changes
MUL
MUL 81,71,81

Example 7: homing

If you are using an operating mode with spatial control (9, 10 or 11) and you need to align the
motor with a zero position defined by a proximity sensor when the system is powered up. You can
use two digital inputs, one for the homing command and one to acquire the proximity sensor signal.
The commands are pulse type and the homing command is executed once only.
After setting the default values set up the required operating mode (Pr31=xx, b99.11=1,
b40.2=1, and any other settings required) and then set the homing speed for the zero proximity
sensor in Pr5 and set b40.12=1 to enable Pr5 when b40.2 reaches zero.
Terminal 13 on X3 = pulse command - execute homing.
Terminal 14 on X3 = PNP axis zero proximity sensor.
Bit b91.10 is utilised to signal that the operation is terminated. Note that bits from b91.8 to b91.15
are at the disposal of the PLC and cannot be stored in the memory.

The program is as follows:

90.2 91.10 40.2 LD 90.2 If homing command not


RST ANDN 91.10 executed, disables operating
RST 40.2 mode
91.10 40.2

SET LD 91.10 If homing command executed,


SET 40.2 re-enables operating mode
90.3 91.10 70.10

SET LD 90.3 if proximity switch operated


ANDN 91.10 resets operating mode counters
91.10 SET 70.10 sets homing executed flag
SET SET 91.10

In certain cases a more precise axis zero reference is required; this is achieved using, in addition
to the proximity sensor on the machine, also the motor position transducer. In this setup the proximity
sensor signal is correlated with the first zero on the motor position transducer.
The following example provides this functionality using operating mode (9) (trapezoidal profile).

65
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

After setting default values, set up operating mode 9 (Pr31=9, b99.11=1, b40.2=0, b40.12=1,
and any other settings required) and then enter the zero proximity sensor homing speed in Pr5.
Terminal 13 on X3 = homing pulse command.
Terminal 14 on X3 = PNP type axis zero proximity sensor.
Terminal 11 on X2 = digital output. Switches to 1 when the homing phase is terminated.
The following bits are utilised b91.8, b91.9, b91.11.

The program is as follows:

LD 90.2 If homing command is given


90.2 91.9 40.2
ANDN 91.9 and not yet executed, disables
RST RST 40.2 operating mode: the motor
runs at speed set in Pr5
90.3 91.0 91.9
LD 90.3
SET ANDN 91.0 when proximity sensor
SET 91.9 operates alignment is enabled
40.2
SET 40.2 on the resolver zero position
SET

91.9 41.2 91.8 79 28 64


LD 91.9
AND 41.2 proximity sensor trip is
SUB
ANDN 91.8 followed by trapezoidal profile
70.8 SUB 79.28.64 to align with resolver zero
SET 70.8 position
SET
SET 91.8
91.8

SET

91.8 70.8 91.0 91.0 LD 91.8


ANDN 70.8 if alignment with resolver zero
SET ANDN 91.0 is terminated, sets axis zero
SET 91.0 terminated output
41.4 91.11 40.2

SET LD 41.4
ANDN 91.11 if drive is OK operating mode
91.11
SET 40.2 is enabled
SET SET 91.11

66
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Example 8: execution of modulus in digital locking

(FILE: E001.HPD)
To obtain the following functionality: with reference to the figure assume you have a conveyor
transporting product and a blade roller driven by the HPD drive. At start up on an external command
the blade roller is aligned with a zero reference (proximity sensor). On receipt of the next pulse
command, which is generated by a product detection sensor, the blade roller drive locks onto the
conveyor master so that the product is always cut at precisely the same length; when the cut is
terminated the blade roller reassumes the starting position awaiting the next cutting command.
In this case the program permits the homing procedure (see chapter 1) and then, on receipt of the
command from the product sensor, it assumes digital locked mode and covers a space equal to the
value of Pr87:86; when it reaches this distance the drive unlocks and ramps down to the standby
position defined by parameter Pr89:88 = modulus. Note that one motor shaft revolution corresponds
to 4096 steps so the modulus value to set is equal to the number of steps required by the motor shaft
to execute a full revolution of the blade roller. The value of Pr87:86 must be less than the value of the
modulus (=Pr89:88).
The master encoder mounted to the conveyor shaft provides the drive with a position reference
during the digital locking phase.

BLADE
PROX SENSOR
SLAVE MOTOR

SENSOR

E
MASTER ENCODER

When you have set the default values set the following parameters: Pr5=10 (homing speed),
Pr31=10, b99.11=1, b40.2=1, b40.12=1, Pr52=0, b70.3=1, Pr87:86=modulus - ramp,
Pr89:88=modulus in which the ramp is expressed in steps, i.e. it is the space that the axis must cover
during ramp down. Pay attention when programming Pr89:88 and Pr87:86 because these
parameters are utilised as double word format by the PLC but they must be set up as two pairs of
single whole words from the keypad. For example, if the modulus is 40960 steps, Pr89 must be set
to 0 and Pr88 must be set to 24576.
Terminal 13 on X3 = homing pulse command
Terminal 14 on X3 = NPN type axis zero proximity sensor
Terminal 12 on X3 = pulse command - digital locking engage sensor.
Terminal 12 on X2 = exit - high during modulus execution; if a digital lock command is transmitted
during execution of the modulus it will be ignored.
The delay before digital locking varies by up to 2.048 msec max.
The following auxiliary parameters are utilised: Pr83, Pr84, Pr85, b91.10, b91.12.
It is assumed that parameter Pr34 is not used. The program is as follows:

67
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

70.8

FIN
FIN 8.1 Fast input for digital lock trigger
90.1 70.8 94.5
LD 90.1 if the axis is locked
SET
AND 70.8 fast input disabled
91.1
SET 94.5 and output enabled (cycle in progress)
SET
SET 91.1 if homing has been carried out the bit is enabled.
91.10 70.8 94.0
LD 91.10
SET
AND 70.8 Force double word operation (comparison)
86 62 84
SET 94.0 comparison for release test
SUB
SUB 86.62.84
85.15 55 72 05 AND 85.15 release test Pr86<Pr62
ADD ADD 55.72.05 copy master speed into internal speed reference
40.2 and enable it
RST RST 40.2
70.8 release axis
RST RST 70.8
94.0 force double word operation
SET SET 94.0
88 62 84 Pr84 = remaining space
SUB SUB 88.62.84
94.0
force double word operation
SET
SET 94.0
84 55 83
Pr83 = time to reach zero rpm
DIV
DIV 84.55.83
91.12
ramp stopped flag
SET 91.12
SET
91.12 94.0 LD 91.12 ramp down management?
SET SET 94.0 Force double word operation
88 62 84 SUB 88.62.84 Pr84 = remaining space
SUB

94.0 SET 94.0 force double word operation


SET

84 83 84
DIV 84.83.84 calculate ramp speed
DIV

72 84 05
ADD 72.84.05 and write in internal reference
ADD
41.2 72 72 60 AND 41.2 if speed is zero..........
ADD ADD 72.72.60 reset position reference (modulus close)
94.0
SET 94.0 force double word operation
SET

62 88 62
SUB 62.88.62 subtract modulus from motor dimension
SUB

91.12
RST 91.12 deactivate ramp in progress flag
RST
RST 91.1 deactivate cycle in progress output
91.1

RST
RST 94.5 enable fast output
94.5
LD 91.10
RST
ANDN 91.12 test if reference must be Pr6
91.10 91.12 40.2
SET 40.2
SET
LD 90.2 test whether to execute homing
90.2 91.10 40.2 ANDN 91.10 execute homing
RST RST 40.2
90.3 91.10 70.10 LD 90.3 zero proximity sensor input
SET ANDN 91.10 honing end test…
91.10 SET 70.10 position reset
SET SET 91.10 homing flag
94.5 RST 94.5 enable fast input
91.10 94.5
RST LDN 91.10 if homing not executed
SET
SET 94.5 disable fast input
END program end
END

68
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Example 9: movement with digital locking and return to origin

(FILE: E002.HPD)
To obtain the following functionality: with reference to the figure below assume there is a
conveyor transporting product and a carriage running parallel to the conveyor and controlled by an
HPD drive. On receipt of an external start command the carriage is aligned on a zero reference
position (proximity sensor). With a second pulse command, provided by a product detection sensor,
the drive locks on to the conveyor in order to perform an operation on the product at a precisely
defined position; when this operation is terminated the carriage returns to its starting position.
In this case the program makes it possible to execute homing (see chapter 1) after which, on
receipt of the manual command from the sensor, the carriage locks on and covers a distance equal to
the value of Pr87:86; when this distance is reached the drive unlocks and stops according to the
ramp programmed in parameter Pr83. The motor now automatically returns to the origin position
executing a trapezoidal profile with the ramps set in Pr80 and the speed in Pr81. Note that one
motor revolution corresponds to 4096 steps so the value to set in Pr87:86 should correspond to the
number of steps of the motor shaft needed for the carriage to execute the required translation.
The master encoder on the conveyor shaft provides the drive with the necessary position
reference during digital locking.
SLAVE MOTOR

PROX SENSOR
M

CARRIAGE

SENSOR

E
MASTER ENCODER

After having set the default values, program the following parameters:
Pr5=10 (homing speed), Pr31=10, b99.11=1, b40.2=1, b40.12=1, Pr80=trapezoidal profile ramp,
Pr81=trapezoidal profile speed, Pr82=copy of P.51 in digital locking, Pr83=digital locking release
deceleration ramp, Pr84=copy of Pr53 in digital locking, Pr87:86=release dimension in steps
terminal 13 on X3 = pulse command for homing execution
terminal 14 on X3 = axis zero position PNP proximity sensor
terminal 12 on X3 = digital locking sensor pulse command
terminal 12 on X2 = output; high during cycle execution; digital locking commands received during
cycle execution will be disregarded.
The digital locking delay interval can be up to 6.144 msec.
The following auxiliary bits are utilised: b91.10, b91.12.
Program (see on next page) :

69
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

91.12 70.8 LD 91.12


SET SET 70.8 return start management
91.12 RST 91.12 with trapezoidal profile
RST

91.10 40.2 LD 91.10


SET 40.2 if homing exec. ref=pr6
SET

90.1 70.8
AND 90.1 locking start request
SET
SET 70.8 locking
91.1
SET 91.1 cycle output on
SET
ADD 72.72.52 no ramp pr52=0
72 72 52

ADD
LD 90.2
90.2 91.10 40.2
ANDN 91.10 homing request
RST RST 40.2
90.3 91.10 70.10 LD 90.3
SET ANDN 91.10 stand by for proximity
91.10 SET 70.10 reset dimensions
SET SET 91.10 homing exec. flag
31.1 91.10 91.1 94.0 LD 31.1
AND 91.10 if OPM = 10
SET
AND 91.1 if homing is done
86 60 88
SET 94.0 and locked
SUB
SUB 86.60.88 forces double word
89.15 72 83 52
AND 89.15 release dimension reached ?
ADD
ADD 72.83.52 set release ramp
70.8
RST 70.8 and release axis
RST
AND 41.2 if speed is zero
41.2 31 31 31
SUB 31.31.31 disable OPM
SUB
ADD 72.72.70 reset all b70
72 72 70

ADD ADD 72.80.51 trapezoidal profile ramp


72 80 51

ADD ADD 72.81.52 trapezoidal profile speed


72 81 52

ADD ADD 72.60.64 copy position in incremental


72 60 64
dimension
SET 70.4 and reverse for return
ADD
set OPM 9
70.4

SET
ADD 71.75.31
preset start
71 75 31
profile at next scan
ADD
SET 91.12
91.12 if no profile in exec.
SET
LDN 70.8 Motor stopped
70.8 41.2 91.12 31.0 31 31 31
AND 41.2 no profile preset
SUB
ANDN 91.12 and OPM is 9
72 82 51
AND 31.0 disable OPM
ADD
SUB 31.31.31 reset ratio
72 84 53 ADD 72.82.51 reset ratio
ADD ADD 72.84.53 zero set slip
72 72 58 ADD 72.72.58 zero set all bits
ADD ADD 72.72.70
72 72 70

SET 70.6 enable feed forward


ADD

70.6
ADD 72.75.31 set OPM 10
SET

72 75 31
RST 91.1 zero set current cycle
ADD

91.1
END program end
RST

END

70
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Example 10: Inter-Drive Communication

IDC (Inter Drive Communication) refers to a specific configuration of the serial port of the HPD
drive that makes it possible to interchange parameters between two or more units.
With IDC enabled (Pr26=10) if bit b99.5 is set to 1 the HPD activates a broadcast command by
sending the value of Pr81 to the address of Pr80. HPDs that receive broadcast commands with
Pr26=10 automatically set b99.5 to 1 causing automatic transmission of Pr81 to the address of Pr80
in broadcast mode. Using this potential, it is extremely simple to connect two HPD drives in a loop
via the serial ports, and a short program on the internal PLC will suffice to start transmission at
power-on and restore it in the event of communication errors. The following example describes the
PLC program required to copy Pr81 from the two drives in parameters Pr80.

Connection function
drive 1 drive 2
X5 X5 drive 1 drive 2
1 1
2 2 Pr81 Pr80
3 3
4 4
5
6
5
6
Pr80 Pr81
7 7
8 8

99.5 75 74 92
LD 99.5 If broadcast is received
DIV timer is set to 30ms
DIV 75.74.92
99.0 99.5 if time-out is present
LD 99.0
SET
SET 99.5 reset serial comms
75 74 92
DIV 75.74.92 and set timer
DIV

These PLC instructions must be entered on only one of the drives; both drives must have
parameter Pr26=10 to enable the IDC function.

71
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Example 11: automatic undervoltage alarm reset

In applications in which the auxiliary backup power supply is utilised it may be necessary to reset
the undervoltage alarm automatically after power has been lost and restored. Simply set the following
instructions in the PLC program:

99.13 20 80 72 LD 99.13 Check real DC bus


SUB SUB 20.80.72 voltage, if > than Pr80
LD 99.2
99.2 76 78 92 ADD 76.78.92 set delay time
ADD LDN 24.0
AND 24.1 If Pr24 = 2, i.e.
24.0 24.1 24.2 24.3 99.0 99.10 ANDN 24.2 undervoltage alarm and
SET ANDN 24.3 timer expired
AND 99.0 reset alarms
SET 99.10

Only the undervoltage alarm (Pr24=2) is reset automatically; the nominal DC bus voltage -10%
must be set in parameter Pr80 (for 380V~ power supplies Pr80=500); timer 1 must not be utilised in
any other section of the pico-PLC program.

72
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Example 12: 5 positioning with teach-in

(FILE: E003.HPD)
To obtain the following functionality: with reference to the figure, assume you need to acquire 5
different machine positions and then execute them automatically.

MOTOR

PROX SENSOR
M

CARRIAGE

POSITIONS: 0 1 2 3 4 5

This can be achieved using a smart keypad module (see appendix L, SBC1 program) connected
on the serial communications line with the drive and with the internal PLC. When the machine is
powered up the drive will stand by to receive the homing exec command and the keypad will show
the message “axis zero (F4)”. By pressing [F4] or sending a pulse command to digital input 2 of the
drive, the motor shaft will turn at the speed established by parameter Pr5 until the intervention of the
proximity sensor at digital input 3. The keypad display will now present the message “automatic
dimension 1”; digital inputs 4, 5 and 6 select the position to be reached, while a pulse supplied to
digital input 1 provides a trapezoidal profile to reach the selected position. The following table shows
the relationship between parameters Pr80...Pr89 and the encoding of the 3 digital inputs; for
example, input 4 on one selects position 1 and the distance in steps between the zero axis point and
position 1 is set in Pr81:80, bearing in mind that one revolution of the motor shaft is equivalent to
4096 steps.

Input 6 Input 5 Input 4 position dimension


0 0 1 1 Pr81:80
0 1 0 2 Pr83:82
0 1 1 3 Pr85:84
1 0 0 4 Pr87:86
1 0 1 5 Pr89:88
other combinations 0 axis zero

If you want to set the dimension from the keypad, press [F3] and the display will show the
message “dimension xx yyyy“ where xx defines the dimension in question and yyyy determines the
relative value. The [+] and [-] keys are used to modify the value yyyy while [F3] changes the value
xx.
If you wish to acquire the required position by moving the carriage, press [F1]: the display will
show the message “manual dimension xx “; [F1] selects the xx dimension to be programmed while

73
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

[+] and [-] are used to move the carriage. The [+] key provides the motor start/stop in the positive
direction, while [-] provides the start/stop in a negative direction; the translation speed in this case
must be set in parameter Pr4. Once the required position has been reached, press [C] to confirm the
dimension. Press [F2] to set automatic mode.
To store the parameters you have programmed press [S].
After having set the default values, set the following parameters on the HPD drive:
Pr4=10 manual translation speed
Pr5=5 homing speed
Pr31=9, b99.11=1, b40.2=1, b40.12=1
Pr81:80=dimension 1
Pr83:82=dimension 2
Pr85:84=dimension 3
Pr87:86=dimension 4
Pr89:88=dimension 5
terminal 12 on X3 = pulse command - execute positioning
terminal 13 on X3 = pulse command - execute homing
terminal 14 on X3 = PNP zero axis proximity sensor
terminal 15 on X3 = select position
terminal 16 on X3 = select position
terminal 17 on X3 = select position
terminal 11 on X2 = output: high during homing
terminal 12 on X2 = output, high during positioning
terminal 13 on X2 = output, high during manual translation
The following auxiliary bits are utilised: b91.10, b91.11.
The program is as follows:

90.2 91.10 40.2


LD 90.2 If digital input 2 and homing not yet
RST ANDN 91.10 executed, executes homing
90.3 91.10 70.10 RST 40.2
SET
LD 90.3 If digital input 3 and homing not yet
91.10 ANDN 91.10 executed
SET

91.0
SET 70.10 reset mode counters
SET 91.10 set homing executed flag
RST
RST 91.0 set digital output 0 to zero
70.8 91.1

LD 70.8 copy bit b70.8 to digital output 1


OUT 91.1
41.4 91.11 40.2

SET LD 41.4 if drive OK, enable operating mode


91.11 ANDN 91.11 at power up
SET 40.2
SET
SET 91.11
END
END program end

Inputs and outputs can be read and written directly via the serial communications line so there is no
need to use the pico-PLC if you have an intelligent unit connected to the drive via the serial line. For
more information regarding the serial line, refer to the HPD user manual.

74
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Example 13: 5 positioning

(FILE: E004.HPD)
Referring to the figure below, assume you need to move the carriage to 5 different positions
selected by means of three digital signals.

MOTOR

PROXIMITY SENSOR
M

CARRIAGE

POSITIONS: 0 1 2 3 4 5

The positions are set in parameters Pr80...Pr89 in resolver steps taking the position of the
proximity sensor as the zero value. When the machine is powered up the drive remains in standby
mode awaiting the homing execution command: when a pulse command is supplied to digital input 2
of the HPD drive the motor shaft will turn at the speed set in parameter Pr5 until the proximity switch
provides a signal at digital input 3. At this point digital inputs 4, 5 and 6 select the position to be
reached, while a pulse on digital input 1 makes it possible to perform positioning on a trapezoidal
profile. The following table shows the relationship between parameters Pr80...Pr89 and the encoding
on the 3 digital inputs; for example, only input 4 on one selects position 1 and the distance in steps
between the zero axis point and position 1 is set in steps, bearing in mind that one revolution of the
motor shaft corresponds to 4096 steps.

Input 6 Input 5 Input 4 Position Dimension


0 0 1 1 Pr81:80
0 1 0 2 Pr83:82
0 1 1 3 Pr85:84
1 0 0 4 Pr87:86
1 0 1 5 Pr89:88
other combinations 0 axis zero

After having set the default values, set the following parameters on the HPD unit:
Pr5=5 homing speed
Pr31=9, b99.11=1, b40.2=1, b40.12=1
Pr81:80= dimension 1
Pr83:82= dimension 2
Pr85:84= dimension 3
Pr87:86= dimension 4
Pr89:88= dimension 5

75
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

terminal 12 on X3 = execute positioning - pulse command


terminal 13 on X3 = execute homing - pulse command
terminal 14 on X3 = PNP axis zero proximity sensor
terminal 15 on X3 = position selection
terminal 16 on X3 = position selection
terminal 17 on X3 = position selection
terminal 12 on X2 = output, high during positioning
The following auxiliary bits are utilised: b91.10, b91.11.
Program:

91.10 40.2 LD 91.10 If homing already


SET SET 40.2 executed enable operating
90.2 91.10 40.2
mode
LD 90.2
RST
ANDN 91.10 If digital input 2 execute
90.3 91.10 70.10
SET 40.2 homing if not yet done
SET LD 90.3
91.10 ANDN 91.10 if digital input 3 and
SET
SET 70.10 homing not executed:
SET 91.10 reset counters
70.8 72 72 64
homing exec flag
ADD
LDN 70.8 digital output 0 at zero
90.4 90.5 94.0 ADD 72.72.64
SET AND 90.4 if profile terminated,
80 72 64 ANDN 90.5 select dimension
ADD
SET 94.0 according to the three
ADD 80.72.64 digital inputs
90.6 94.0
AND 90.6
SET
SET 94.0
88 72 64 ADD 88.72.64
ADD LDN 70.8
70.8 90.5 90.6 94.0
AND 90.5
SET
ANDN 90.6
SET 94.0
82 72 64
ADD 82.72.64
ADD AND 90.4
90.4 94.0 SET 94.0
SET ADD 84.72.64
84 72 64
LDN 70.8
ANDN 90.4
ADD
ANDN 90.5
70.8 90.4 90.5 90.6 94.0
AND 90.6
SET SET 94.0
86 72 64 ADD 86.72.64
ADD if profile terminated and
70.8 91.10 90.1 70.8
LDN 70.8 input 1=1 execute profile
AND 91.10 resetting direction bit and
SET
AND 90.1 calculating distance with
70.4
SET 70.8 respect to current motor
RST RST 70.4 position
64 60 64 SUB 64.60.64 if negative sign set
SUB
AND 99.2 b70.4=1
99.2 70.4
SET 70.4
digital output 2 indicates
SET
LD 70.8 profile on
70.8 91.1 OUT 91.1 program end
END

END

76
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Example 14: reading 4-digit preselector (BCD Thumbwheels)

(FILE: E005.HPD)
To change the value of parameter Pr82 by means of a 4-digit preselector. This procedure
involves the use of four digital outputs and four digital inputs:
terminal 12 on X2 = output for selection of first preselector digit (least significant)
terminal 13 on X2 = output for selection of second preselector digit
terminal 14 on X2 = output for selection of third preselector digit
terminal 15 on X2 = output for selection of fourth preselector digit
terminals 12...15 on X3 = inputs for reading digit in BCD (terminal 12 is least significant bit;
connection diagram shown on next page).

90.1 80.0
LD 90.1 Copy bit 0 BCD digit
OUT 80.0

90.2 80.1
LD 90.2 copy bit 1 BCD digit
OUT 80.1

90.3 80.2 LD 90.3 copy bit 2 BCD digit


OUT 80.2

90.4 80.3 LD 90.4 copy bit 3 BCD digit


OUT 80.3

91.1 80 73 81 LD 91.1 if first digit


MUL 80.73.81 calculate units
MUL

91.2 80 75 81 LD 91.2 if second digit


MUL 80.75.81 calculate first decimal place
MUL

91.3 80 76 81 LD 91.3 if third digit


MUL 80.76.81 calculate second decimal place
MUL

91.4 80 77 81 LD 91.4 if fourth digit


MUL 80.77.81 calculate third decimal place
MUL

99.13 81 82 82 LD 99.13 add calculation result to auxiliary


ADD
ADD 81.82.82 parameter Pr81

91.4 82 72 83 LD 91.4 if last digit (most significant)


ADD
ADD 82.72.83 copy final value in Pr83

82 82 82 SUB 82.82.82 zero set parameter Pr82


SUB
LD 91.3 refresh outputs to enable reading of
91.3 91.4 OUT 91.4 next digit

LD 91.2
91.2 91.3
OUT 91.3

LD 91.1
91.1 91.2
OUT 91.2
LDN 91.2
ANDN 91.3 if last digit already acquired, start
91.2 913 91.4 91.1
ANDN 91.4 scanning digits starting from units
OUT 91.1
END
END program end

77
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

CONNECTION OF 4-DIGIT PRESELECTOR

15
14
X2 13
12

15
14
X3 13
12

1 2 4 8 C 1 2 4 8 C 1 2 4 8 C 1 2 4 8 C

x1000 x100 x10 x1

Example 15: programmable zero speed window

Assume you want the value of the main analogue reference to remain below a programmable
threshold when it is cancelled. In practice, a speed window around zero rpm is defined within which
speed is set to zero. The value of the threshold is set in parameter Pr88 in rpm; parameter Pr89 is
used as an auxiliary memory area.

The required pico-PLC program is as follows:

99.13 07 72 89 LD 99.13 Copy analogue reference value in Pr89


ADD ADD 07.72.89
89.15 89 71 89
LD 89.15 if Pr89 < 0 invert Pr89 to obtain the
MUL MUL 89.71.89 modulus
99.13 89 88 72

SUB
LD 99.13 calculate difference between Pr89 and
SUB 89.88.72 Pr88:
99.2 40.6
AND 99.2
OUT 40.6 if negative, set drive to stop

78
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

3.9 Programming with Pcbrush

The HPD serial kit is supplied to enable communication between a PC and the drive. The kit
includes an RS-422/RS-232 converter, relative 230V~ power supply and serial connection cable.
The enclosed communication software (supplied free of charge) designated Pcbrush has the
following HW/SW requirements: 486 microprocessor or higher, Windows* 3.1 or more recent
version, mouse and serial port for drive connections. The main features of Pcbrush are:
- serial connection of up to 32 drives
- reading and setting of basic parameters and drive commands
- reading and setting of commands and parameters of operating modes
- functional block diagrams
- pico-PLC program displayed as ladder diagrams
- display of pico-PLC program status during operation
- I/O status
- file storage of parameterisation including pico-PLC program
- uploading of parameterisation including pico-PLC program from a file that can be selected from
among those previously stored
- speed regulator and position controller simulation

PC - HPD connection layout (HPD serial kit):


CL-422 X5 (HPD)

personal computer
17 1
RS-232
DB9 DB25
tx 5 3
3 2
rx 14 2
2 3
0V 2 4
5 7
RS-422 7 8

refer to text for burden resistors

To create line load (burden) resistances, jumper pins 2 and 6, and pins 4 and 7 on connector X5
of the last drive on the serial line.
If the PC is a battery powered laptop (i.e. not connected to ground) use the following connection
layout:
personal computer
X5 (HPD)
DB9 DB25
8

5 7 1

3
2 3
4
3 2

To install Pcbrush open WINDOWS*, insert the diskette in drive A, select the File menu in
Program Manager and then the Run.option. Now run Setup.exe on [A:\] by typing the following
string on the Command line: A:\setup.exe or by selecting the file with the Browse...button. The
following installation procedure automatically creates a new icon for Pcbrush. Once the program is
installed, launch it by double clicking the relative icon (or select the icon and then press ENTER).
Set the following parameters on the drive: Pr26=6, Pr27=0, b40.14=1, b42.3=1.

* Windows and the Windows logo are registered trade marks or trade marks owned by Microsoft Corporation in the United States
of America and/or other countries.

79
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

4 - SERIAL INTERFACE

The drive communication protocol is “master-slave” half-duplex type on an asynchronous RS-


485/RS-422 line. The drives assume control of the line only following interrogation by the master.
Up to 32 drives can be connected on the same serial line, allocating each a different serial address
in parameter Pr27. It is also possible to set transmission speed in parameter Pr26 as specified in the
table:

Pr26 (decimal base) b/s time-out (ms)


0 600 512
1 1200 256
2 2400 128
3 4800 64
4 9600 (*) 32
5 9600 32
6 19200 16
7 38400 12
8 57600 8
9 125000 4
10 57600 (**) 8

(*) The version with code Pr26=4 differs from Pr26=5 because of the 25 ms response delay. This
version was developed to interface with PLCs that require this characteristic.
(**) The version with code Pr26=10 was developed to allow data communication between two
HPD drives.

Refer to the heading Serial line connection for connection diagrams.

4.1 Communication protocol

The right hand column in the table shows the time-out value in milliseconds for each
communication speed; this is the time, starting from the beginning of each message (STX) within
which the transmission of the message must terminate. Therefore, if the message is interrupted, after
the time-out the drive will ignore the information already received and stand by to receive a new
message.
Messages are made up of several consecutive data in the following format:
1 start bit
8 data bits following one byte between square brackets
1 parity bit (even)
1 stop bit
The message structure is:
[STX] [CMD+ADDR] [LUN] [PAR] [D0] ... [Dn] [CHK]
where:

80
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

[STX] = $7E transmission start indicator. If a field other than STX should assume the value $7E in
the message, this field is followed by a ($00) to ensure that it cannot be interpreted as an [STX].
[CMD+ADDR] = command and address of peripheral device, always different to zero. This datum
is composed as follows: the first 5 bits (from 0 to 4) define the drive address (from 0 to 31); the
remaining 3 bits (from 5 to 7) define the type of message, as described in the following table:

CMD bit 7 bit 6 bit 5 message type


1 0 0 1 drive response
2 0 1 0 read PLC instruction
3 0 1 1 write PLC instruction
4 1 0 0 read parameter
5 1 0 1 write parameter
6 1 1 0 bit change
7 1 1 1 broadcast parameters to all drives

[LUN] = total number of bytes transmitted (parameter or PLC instruction); can assume values from
1 to 4. This value must not hold zero characters ($00) after values that coincide with the initial
transmission character ($7E).
[PAR] = parameter or PLC instruction read/write address
[D0] ... [Dn] = datum transmitted.
[CHK] = 256 modulus sum of all fields except [STX] (checksum).

Message types

[CMD1] = drive response to data request, format:


[STX] [001+ADDR] [LUN] [PAR] [D0] ... [Dn] [CHK]
or confirm message in response to data entry or update, format:
[STX] [001+ADDR]
where ADDR identifies the answering drive.

[CMD2] = read message of PLC area instruction; format:


[STX] [010+ADDR] [LUN] [PAR] [CHK]

[CMD3] = write message of PLC area instruction; format:


[STX] [011+ADDR] [LUN] [PAR] [D0] ... [Dn] [CHK]

[CMD4] = parameter read message; format:


[STX] [100+ADDR] [LUN] [PAR] [CHK]

[CMD5] = parameter write message; format:


[STX] [101+ADDR] [LUN] [PAR] [D0] ... [Dn] [CHK]

[CMD6] = byte parameter bit change message; format:


[STX] [110+ADDR] [LUN] [PAR] [D0] [D1] [CHK]
In this case (LUN=2) two bytes are transmitted for the data: the first byte is the mask containing
0 in the positions of the bits to change and 1 in the other positions; the second byte contains 1 in bit
positions to be set to 1 and 0 in the other positions. The address PAR corresponds to the parameter

81
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

(byte) in which one or more bits is to be modified. If the parameter is a word and the bit to be
modified is among the first 8 (b0...b7): PAR = parameter address; otherwise if the bit to modify is
one of the upper 8 (b8...b15): PAR = parameter address + 1.

[CMD7] = parameter write broadcast message to all drives connected to the serial line; format:
[STX] [11100000] [LUN] [PAR] [D0] ... [Dn] [CHK]
The address of peripheral device (ADDR) must be zero.

Notes:
- Parameters shown on the display with decimals must be treated as integer values, e.g. 978.5 will
be read, and written, as 9785.
- All values preceded by the symbol $ are hexadecimal numbers.
- The value in square brackets is the basic unit (byte) of the message.
- To be considered valid all messages must be terminated within a clearly defined time interval
(time-out) which is a function of speed, and they must have correct parity and checksum.
- The drive responds to data requests or transmission only if the message is received correctly; if
the message contains an error, no answer will be transmitted. The only exception is message type
7, with which a datum is transmitted with a single message addressed to all drives connected to
the serial line.

Serial line initialisation and management

Drive serial communication can be enabled or disabled by means of bit b40.14.


The drive is factory set with b40.14=0, i.e. serial line disabled (default).
If you want to use the serial line first set the baud-rate in Pr.26; now set the serial address in
Pr.27; finally, enable serial communication by setting b40.14=1 and initialise using b42.3. At this
point you must save the configuration using command b99.15.

For parameter addresses and lengths refer to the relative table.


In the case of PLC instructions, each one occupies 2 or 4 bytes, the format of which is described
below.
Instruction code length (bytes)
LD Pa.y 0 2
LDN Pa.y 1 2
OUT Pa.y 2 2
OUTN Pa.y 3 2
AND Pa.y 4 2
ANDN Pa.y 5 2
OR Pa.y 6 2
ORN Pa.y 7 2
ADD Pa, Pb, Pc 8 4
SUB Pa, Pb, Pc 9 4
MUL Pa, Pb, Pc 10 4
DIV Pa, Pb, Pc 11 4
SET Pa.y 12 2
RES Pa.y 13 2
FIN Pb40.y/Pb70.y 14 2
END 15 2

82
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

The memory area available for PLC instructions is 128 bytes, with addresses from 0h to 7Fh.
As the minimum length for each instruction is 2 bytes, the PLC program can hold a maximum of
64 instructions.
The first four bits of the first byte in each instruction (b0..b3) contain the instruction code.
For the first 8 instructions in the table (LD...ORN) and the SET and RES instructions, the
remaining 4 bits of the first byte (b4..b7) contain the value y, while the second byte contains the
value Pa.
For instructions ADD, SUB, MUL and DIV, the second byte contains the value Pa, the third Pb,
and the fourth Pc.
The second byte is not utilised for the END instruction.
For the FIN instruction the fifth bit (b4) of the first byte selects the parameter: b4=0 refers to
Pr.40, b4=1 refers to Pr.70; the sixth bit (b5) of the first byte is used for negative logic if required:
b5=0 the bit is copied; b5=1 the bit is inverted and then copied. The second byte of the FIN
instruction contains the value of y.
If FIN instructions are used they must be the first of the program and there must be no more than
3 so they will occupy addresses from 0h to 5h. If a FIN instruction is included from address 6h
forward or, anyway, after any other instruction, it will be ignored (NOP).
The instructions must be one after the other starting from address 0h, without any free bytes.
There is just one program and it terminates with the END instruction.

Serial line application examples

For a better understanding of how to implement the serial line communication protocol, we have
provided a few examples for each type of message.
The values are entered simply by way of example.

Case 1: reading a 1 byte parameter


Assume you want to read the value of parameter Pr.31 (operating mode), and that the value of this
parameter is 9; assume the drive serial address is 0. The message to transmit is:
[$7E][$80][$01][$54][$D5]
The drive answers with the message:
[$7E][$20][$01][$54][$09][$7E][$00]

Case 2: reading a 2 byte parameter


Assume you wish to read the reference speed (Pr.7) and that the relative value is 2000; assume also
that the drive serial address is 1. The message to transmit is:
[$7E][$81][$02][$42][$C5]
The drive answers with:
[$7E][$21][$02][$42][$D0][$07][$3C]

Case 3: writing a 1 byte parameter


Assume you want to select operating mode 1 (Pr.31); assume also that the drive serial address is 3.
The message to transmit is:
[$7E][$A3][$01][$54][$01][$F9]
The drive answers with:
[$7E][$23]

83
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Case 4: writing a 2 byte parameter


Assume you intend to set rated current at 25.3% (Pr.33); assume also that the drive serial address is
3. The message to transmit is:
[$7E][$A3][$02][$C6][$FD][$00][$68]
The drive answers with:
[$7E][$23]

Case 5: setting a bit to 1


Assume you want to enter the command to save the PLC program (b99.14=1); assume also that the
drive serial address is 0. The message to transmit is:
[$7E][$C0][$02][$93][$BF][$40][$54]
The drive answers with:
[$7E][$20]

Case 6: setting a bit to 0


Assume you want to disable the drive by software (b40.9=0); assume that drive serial address is 0.
The message to transmit is:
[$7E][$C0][$02][$5D][$FD][$00][$1C]
The drive answers with:
[$7E][$20]

Case 7: writing a PLC instruction


Assume you want to set the first PLC instruction as: LD 90.4; assume the drive serial address is 0.
The message to transmit is:
[$7E][$60][$02][$00][$40][$5A][$FC]
The drive answers with:
[$7E][$20]

Case 8: reading the first PLC instructions


Assume you want to read the first instructions of the PLC default program; assume the serial address
of the drive is 0. The message to transmit is:
[$7E][$40][$04][$00][$44]
The drive answers with the message:
[$7E][$20][$04][$00][$10][$5A][$A7][$5A][$8F]
which corresponds to the acquisition of the following instructions: LD 90.1, ORN 90.10.

84
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

4.2 Serial addresses and parameter lengths

Parameter Address Length Meaning

Pr0 038h 2 motor speed in rpm


Pr1 034h 2 analogue reference
Pr2 03Ah 2 full scale 1
Pr3 03Ch 2 full scale 2
Pr4 036h 2 frequency full scale
Pr5 03Eh 2 internal reference
Pr6 040h 2 reserved reference
Pr7 042h 2 chosen reference
Pr8 0AEh 2 positive acceleration in seconds
Pr9 0B0h 2 positive deceleration in seconds
Pr10 0B2h 2 negative acceleration in seconds
Pr11 0B4h 2 negative deceleration in seconds
Pr12 0B6h 2 limit switch deceleration
Pr13 0B8h 2 overspeed threshold
Pr14 044h 2 top speed limit
Pr15 046h 2 lower speed limit
Pr16 048h 2 integral gain
Pr17 0BAh 2 damping factor
Pr18 0BCh 2 filter time constant
Pr19 0BEh 2 user current limit
Pr20 04Ah 2 DC bus voltage
Pr21 04Ch 2 reserved torque limit
Pr22 04Eh 2 auxiliary reference
Pr23 051h 1 current alarm code
Pr24 052h 1 previous alarm code
Pr25 053h 1 software version code
Pr26 05Eh 1 baud rate
Pr27 05Fh 1 serial address
Pr28 0C0h 2 shaft position (0..4095)
Pr29 061h 1 motor poles
Pr30 0C2h 2 resolver offset
Pr31 054h 1 operating mode
Pr32 0C4h 2 rated motor speed
Pr33 0C6h 2 rated current
Pr34 055h 1 scale factor for tacho generator
Pr35 0C8h 2 filtered torque request
Pr36 058h 2 i2t accumulation
Pr37 05Ah 2 thermal image for braking
Pr38 0CAh 2 auxiliary analogue output
Pr39 0CCh 2 K for phase advance
Pb40 05Ch 2 flags used by main block
Pb41 056h 2 flags used by main block
Pb42 060h 1 flags used by main block
Pr50 064h 2

85
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Pr51 066h 2
Pr52 068h 2
Pr53 06Ah 2
Pr54 06Ch 2
Pr55 06Eh 2
Pr56 070h 2
Pr57 072h 2
Pr58 074h 2
Pr59 076h 2
Pr60 078h 2
Pr61 07Ah 2
Pr62 07Ch 2
Pr63 07Eh 2
Pr64 080h 2
Pr65 082h 2
Pr66 084h 2
Pr67 086h 2
Pr68 088h 2
Pr69 08Ah 2
Pb70 062h 2 flags used by operating mode
Pr80 0CEh 2
Pr81 0D0h 2
Pr82 0D2h 2
Pr83 0D4h 2
Pr84 0D6h 2
Pr85 0D8h 2
Pr86 0DAh 2
Pr87 0DCh 2
Pr88 0DEh 2
Pr89 0E0h 2
Pb90 0E2h 2 inputs
Pb91 08Ch 2 outputs
Pr92 08Eh 2 timer 1
Pr93 090h 2 timer 2
Pb94 032h 1 flags used by PLC
Pb99 092h 2 flags used for PLC and commands

PLC area length: 128 bytes, addresses 00h to 7Fh.

86
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Appendix A: HPD drive mechanical dimensions


81.5 301

5.5 5 M5

17
20

316
A B

5.5
40

Dimensions can be changed at discretion of the manufacturer.

drive type A B weight kg


HPD2 348 335 5.1
HPD5, HPD8, HPD16 377 364 5.5

87
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Appendix B: MB series motor connectors

CONNECTIONS FOR MBmax BRUSHLESS MOTORS

resolver A= white-red = EXCT +


B= white-yellow = EXCT - FAN MOTOR CONNECTOR FOR MBmax 105
C= blue = Cos -
D= yellow = Cos +
B A H
E= black = Sin - CONNECTOR (Male) CONNECTOR (Female)
C J K G
F= red = Sin +
G= Gnd (shield of cable) C
D E F
H= Gnd (shield of cable) M A
+
B A B C
K= PTC
J= PTC 24V=
-
motor A = (white)

A F C = (blue)
}
B = (green) motor

G
E
D= Gnd
B
E= Gnd
D F= Brake FAN MOTOR CONNECTOR FOR MBmax 145 and 205
C
G= Brake
} 24V= ±10%
CONNECTOR (Male) CONNECTOR (Female)
alternatively
M
C A A C

B B

F G 220V~
W2 U2 V2
F - G = BRAKE

U1 V1 W1 C-B-A = MOTOR

C B A

88
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Appendix C: hardware characteristics

digital input
input impedance 7 Kohm
VH 15..30 V
VL 0..3 V
digital output
type PNP open collector
VH using internal supply 20..26 V
IO for single output 100 mA
IT current for all outputs 200 mA
using internal supply
IT current for all outputs using 500 mA
ext. supply +24 VIN
VSW max. voltage between 110 V~
out 6 A and out 6 B
ISW max. current trough out 6 A 600 mA
and out 6 B
analogue reference
type differential
impedance 20 Kohm
range ± 10 V
CMMR > 60 dB
resolution 15 bits
aux. analogue input
type differential
impedance 250 Kohm
range ± 10 V
CMMR > 40 dB
resolution 10 bits
analogue output
type single ended
IO max. 1.5 mA
range ± 10 V
resolution 8 bits

89
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Appendix D: DC bus voltage thresholds


1024
800 OVER VOLTAGE
768
BRAKE HIGH THRESHOLD
744 BRAKE LOW THRESHOLD

NORMAL
OPERATION
AREA

120 INRUSH CONTROL ON


56 UNDER VOLTAGE

40 INRUSH CONTROL OFF

Appendix E: Standard settings

Reference Positive
Shaft moving ( motor shaft view ) : clockwise

Torque monitor Positive


R/D Counter UP
Encoder out A
B
tacho signal positive
Iu torque • sin( ϑ )
Iv  2 •π 
torque • sinϑ + 
 3 
IN AUX positive Pr22 positive
Pr38 positive OUT AUX. Positive
Encoder In. A Counter Up
B

90
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Appendix F: Software timers

Time slot Task running


256 µs Torque vector generation
512 µs Speed loop
Fast operating mode manager
Torque limit evaluation
Speed reference manager
Brake resistor manager
Fast input
2.048 ms Slow operating mode
6.144 ms Motor thermal image algorithm
Digital input
PLC instruction scan
Digital output
49.152 ms Speed windows manager

91
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Appendix G: pico-PLC default program

90.1 40.4
LD 90.1
digital input 1 for left hand limit
ORN 90.10
switch enabled only if b90.10=1
90.10 OUTN 40.4

90.2 40.5 LD 90.2


digital input 2 for right hand limit
ORN 90.10
switch enabled only if b90.10=1
90.10
OUTN 40.5

90.3 40.6 LD 90.3


digital input 3 for emergency stop
ORN 90.10
enabled only if b90.10=1
OUTN 40.6
90.10

90.4 40.0 LD 90.4


digital input 4 for clockwise or
OUT 40.0
counter-clockwise rotation
90.5 05 05 05 LD 90.5
digital input 5 for start/stop reset
SUB SUB 05,05,05
parameter Pr5
41.0 91.0
LD 41.0
digital output 0 indicates speed
OUT 91.0
greater than Pr13
41.1 91.1 LD 41.1
digital output 1 indicates motor
OUT 91.1
speed = reference
digital output 2 indicates motor
41.2 91.2
LD 41.2
speed = 0
OUT 91.2
digital output 3 indicates clockwise
41.3 91.3 LD 41.3
or counter-clockwise motor shaft
OUT 91.3
rotation
41.4 91.6 LD 41.4
digital output 6 indicates drive
OUT 91.6
healthy
LD 41.11
41.11 91.4 digital output 4 indicates active
OUT 91.4
motor thermal image
90.11 99.0 92 78 92 LD 90.11
if b90.11=1 the drive performs a
AND 99.0
ADD direction inversion at 6 second
ADD 92,78,92
intervals at the speed in Pr5
05 71 05
MUL 05,71,05
MUL

90.5 40.12
LD 90.5
digital input 5 for start/stop disabled
OR 90.11
if b90.11=1
90.11 OUT 40.12

END
program end
END

92
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Appendix H: flash information

• USE b99.15 TO SAVE PARAMETERS

• USE b99.14 TO SAVE PLC PROGRAM

• TO CHANGE PLC INSTRUCTIONS b99.13 MUST BE AT 0

• WHEN CHANGING OPERATING MODE USE b99.11 TO LOAD DEFAULT


PARAMETERS (b40.2=0)

• WARNING, BEFORE CHANGING Pr31 MAKE SURE b40.2=0

• SPEED REFERENCE IS LIMITED TO THE VALUE IN Pr32

• IN TORQUE CONTROL Pr2 AND Pr3 MUST BE SET TO 1000

• TO USE THE ACTIVE OPERATING MODE b40.2 MUST BE SET TO 1

• TO USE Pr32 TO CHANGE FEEDBACK RESOLUTION ON THE FLY, DISABLE


TORQUE COMPENSATION (b42.6=0)

• IF YOU CANNOT UPDATE READ/WRITE PARAMETERS FROM THE KEYPAD,


MAKE SURE b99.7=0. IF b99.7=0, THE PARAMETERS ARE PROBABLY MANAGED
BY THE PLC PROGRAM.

93
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Appendix I: S.B.C. filter mechanical dimensions

50 126 12.5 25
M5 6.5

15

255 225 240

S.B.C. 3RD-7

M5

Nome del file: H:\ENGINEERING\FILTRI\SCHAFFNER\SBC 3RD_7


Scala Data Firma

s.r.l. Disegn. 15-07-98


= Grezzo Via Gounod,1
12.5 CINISELLO B.(MI) - Contr. 15-07-98
= Sgrossato (ITALY)
-- -- -- 3.2 MOTOVARIATORI Modif.to -- REV. 0
= Lav.Finito
-- -- -- 0.8 Denominazione:
-- -- -- =
0.2
Rettif.to
Motore tipo:
FILTRI S.B.C. 3RD-7 DIS. 3RD-7
Data
MODIFICHE Revisione Descrizione Eseg. da Control. = Lappato

55 142 12.5 30
M5 6.5

15

305 275 290

M5
Nome del file: H:\ENGINEERING\FILTRI\SCHAFFNER\SBC 3RD_16
Scala Data Firma
s.r.l. Disegn. 15-07-98
= Grezzo Via Gounod,1
12.5 CINISELLO B.(MI) - Contr. 15-07-98
= Sgrossato (ITALY)
3.2 MOTOVARIATORI Modif.to -- REV. 0
-- -- -- Lav.Finito
=
-- -- -- 0.8 Denominazione:
= FILTRI S.B.C. 3RD-16
--
Data
MODIFICHE
--
Revisione
--
Descrizione Eseg. da Control. =
0.2
Rettif.to
Lappato Motore tipo: DIS. 3RD-16

94
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

55 142 12.5 30
M5 6.5

15

305 275 290

M5
Nome del file: H:\ENGINEERING\FILTRI\SCHAFFNER\SBC 3RD_16
Scala Data Firma

s.r.l. Disegn. 15-07-98


= Grezzo Via Gounod,1
12.5 CINISELLO B.(MI) - Contr. 15-07-98
= Sgrossato (ITALY)
-- -- -- 3.2 MOTOVARIATORI Modif.to -- REV. 0
= Lav.Finito
-- -- -- 0.8 Denominazione:
-- -- -- =
0.2
Rettif.to FILTRI S.B.C. 3RD-16 DIS. 3RD-16
Motore tipo:
Data Revisione Descrizione Eseg. da Control. = Lappato
MODIFICHE

95
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Appendix L: remote communications interface

If the application calls for a simple operator interface, use console 048+049+064. The console is
connected to the drive by means of the serial line; it does not provide I/O capabilities and it does not
have buffered memory. The connection cable is not part of the standard supply and the software
must be generated by Parker, Divisione S.B.C. to client specifications.

90 90 max

Power supply type 064

F1 F2 F3
SHIFT
128.5 F4 F5 F6

START
A P STOP

ESC C S

Rear panel view

HPD connector P2 pins

4 4

3 5

X5 1 2 P2

2 3

8 8

for burden resistors refer to Serial line connection

L1

3 power
L2 2
1 M1

PE

96
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

Appendix M: application description form


In order to develop our products in co-ordination with user’s needs, we are most
interested to learn about your HPD application. Please fill in this form and return it to us.
This will also enable us to tailor our technical support to your individual requirements.

Fill in these forms in full and keep them with the machine technical
documentation to facilitate maintenance.

to: Parker Hannifin S.p.A. - Divisione S.B.C. / ITALY


R & D department
fax: +39-2-66016116
CUSTOMER name ..........................................
Contact name ..........................................
Tel. ..........................................
Fax. ..........................................
MODEL HPD 2
HPD 5
HPD 8
HPD 16
SERIAL NUMBER _______
MOTOR MODEL ..........................................
MOTOR SERIAL NUMBER ..........................................
OPERATING VOLTAGE ___V
FIRST HPD APPLICATION? YES NO
MACHINE TYPE ..............................................................................
TASK PERFORMED BY AMPLIFIER.................................................
.........................................................................................................................
COMMENTS
...................................................................................................
...................................................................................................
...................................................................................................
...................................................................................................
...................................................................................................

FUNCTIONS USED

EXTERNAL BRAKING MAINS FILTERS ENCODER IN


BACK-UP LOW VOLTAGE FUNCTION ENCODER OUT
PARALLEL BUS INTERNAL PLC
MOTOR COILS SERIAL LINE

AMPLIFIER CONTROLLED BY
MAKE MODEL
NUMERICAL CONTROL
PLC
SINGLE AXIS CARD
MASTER/SLAVE CARD
OTHER....................................

97
Parker Hannifin S.p.A. - Divisione S.B.C. HPD User’s Manual

AMPLIFIER PROGRAMMING
Pr value Pr value Pr value Pr value
1 31 42.5 70.6
2 32 42.6 70.7
3 33 42.7 70.8
4 34 50 70.9
5 39 51 70.10
8 40.0 52 70.11
9 40.1 53 70.12
10 40.2 54 70.13
11 40.3 55 70.14
12 40.4 56 70.15
13 40.5 57 80
14 40.6 58 81
15 40.7 59 82
16 40.8 60:61 83
17 40.9 62:63 84
18 40.10 64:65 85
19 40.11 66:67 86
23 40.12 68:69 87
24 40.13 70.0 88
25 40.14 70.1 89
26 40.15 70.2 99.5
27 42.0 70.3 99.6
29 42.1 70.4 99.7
30 42.2 70.5 99.13

IF YOU USE AN INTERNAL PLC PROGRAM OTHER THAN THE DEFAULT


PROGRAM, PLEASE ENCLOSE THE LISTING.

In 0 In 16 In 32 In 48
In 1 In 17 In 33 In 49
In 2 In 18 In 34 In 50
In 3 In 19 In 35 In 51
In 4 In 20 In 36 In 52
In 5 In 21 In 37 In 53
In 6 In 22 In 38 In 54
In 7 In 23 In 39 In 55
In 8 In 24 In 40 In 56
In 9 In 25 In 41 In 57
In 10 In 26 In 42 In 58
In 11 In 27 In 43 In 59
In 12 In 28 In 44 In 60
In 13 In 29 In 45 In 61
In 14 In 30 In 46 In 62
In 15 In 31 In 47 In 63

98

You might also like