Fluidizing media

for bulk powder

handling and processing

Copyright 1999 MKI

All Rights Reserved

The high-strength cleanable

easily fabricated porous metal sheet
for all fluidizing applications
NO ONE BUT MKI CAN GIVE YOU:

LFM TM and HFM TM media are abrasion and puncture

Dynapore controlled permeability Dynapore resistant and will not chip, flake
media are constructed of multiple layers of carefully or shed fibers. Depending upon load, Dynapore can
selected stainless steel wire mesh, laminated by withstand continuous operating temperatures up to
precision sintering (diffusion bonding ) and calendering. 1000 ˚F with intermittent spikes of 1200 ˚F. The
The resultant monolithic structure is permanently bonded abrasion, corrosion, and temperature resisting properties
and has highly uniform flow characteristics. Dynapore
of Dynapore media are superior to that of polyester,
laminates are ideal for even flow distribution of gases in
metal felts, or sintered powder metals.
fluidizing and aeration applications.

LFM and HFM air flow ratings

Dynapore
is constructed of 100% AISI
Dynapore and pressure drop curves are
type 316 stainless steel. Other
temperature and corrosion resisting alloys are available presented on the adjacent page. LFM 3-layer media range
on special request. Custom laminates offering enhanced in air flow from 5 to 25 scfm/sf @ 2 in. water column
mechanical strength are also available. pressure drop. HFM 2-layer media range from 50 to 400
scfm/sf @ 2 in. water column. Custom permeabilities are
available on special request.
media are easily sheared,
Dynapore formed, punched, welded and For more information,
cleaned using standard equipment and methods. request the following Bulletins:
Dynapore laminates are available from stock in 401 Mechanical Properties
convenient 24”x 48” and 36” x 36” sheets. Larger TIG 402 Installation Recommendations
butt-welded sizes are also available. MKI, of course, 403 Fluidized Conveyor Truss and Bolt Spacing
offers custom fabrication services. 404 Flow Equations and Permeability Constants

Alumina (aluminum oxide) fluidized on Dynapore flows like water.

❏ LIME BINS ❏

❏ CEMENT SILOS ❏

❏ FLY ASH DRYERS ❏

❏ GYPSUM HOPPERS ❏

❏ ALUMINA REACTORS ❏

❏ TEREPHTHALIC AIR-GRAVITY ❏
ACID CONVEYORS
 AIR FLOW CHARACTERISTICS

The air flow rating values for 3-layer LFM and 2-layer HFM Dynapore laminates are
presented in the following tables. LFM laminates cover the air flow range from 5 to 25
scfm/ft2 @ 2 in. water column pressure drop. HFM laminates flow from 50 to 400 cfm/ft2
@ 2 in. water column. In general, HFM media are lower in weight and thickness, and have
larger mean pore sizes.

LFM
LFM HFM
HFM
3-LAYER LAMINATE (WEIGHT 2.0 LBS/FT2) 2-LAYER LAMINATE (WEIGHT 1.5 LBS/FT2)

AIR FLOW NOMINAL AIR FLOW NOMINAL

MEDIUM PART MEDIUM PART
SCFM/FT2 @ ∆ P THICKNESS SCFM/FT2 @ ∆ P THICKNESS
TYPE NUMBER TYPE NUMBER
2 IN. WATER INCHES 2 IN. WATER INCHES

HFM-50 401420 50 0.041

LFM-5 407520 5.0 0.054

HFM-100 401430 100 0.044

LFM-10 401300 10.0 0.058
HFM-200 401440 200 0.050
LFM-25 407530 25.0 0.061
HFM-400 407570 400 0.060

PRESSURE DROP vs AIR FLOW - 3 LAYER DYNAPORE PRESSURE DROP vs AIR FLOW - 2 LAYER DYNAPORE
200 200
UPSTREAM CONDITIONS UPSTREAM CONDITIONS
1 ATM. 70F 1 ATM. 70F
100 100
∆ P, PRESSURE DROP, in. water

80
∆ P, PRESSURE DROP, in. water

80
60 60
40 40

20 LFM-10 20
HFM-50 HFM-400
LFM-5 10
10
8 8
LFM-25 HFM-200
6 6
4
4
HFM-100
2
2
RATING POINT RATING POINT
1
1 1 4 8 20 60 100 400 800 2000
1 4 8 20 60 100 400 800 2 6 10 40 80 200 600 1000 4000
2 6 10 40 80 200 800 1000

G, AIR FLOW,SCFM/ft 2 G, AIR FLOW,SCFM/ft 2

BULK POWDERS FLOW LIKE LIQUIDS ON

STAINLESS STEEL FLUIDIZING MEDIA

A proven product for more than 25 Years
cleanability { Dynapore is easy to clean because ordinary water and
detergent, high pressure steam or chemical methods
may be used to remove most oil and dirt.

{
Dynapore can be easily fabricated, punched, sheared,
easily or formed.Weldability is excellent using TIG or other
fabricated standard methods. Dynapore is available from stock,
in seamless 24” x 48” and 36” x 36” sheets.

air flow
uniformity { High temperature diffusion bonding and precision
calendering create the precise and uniform air flow
properties of Dynapore.

engineered
{
Dynapore laminates are not limited to LFM and HFM
construction. By careful mesh selection and sequencing,
porous media a porous metal medium can be engineered to fit almost
any specification for: pore size; pore density; tortuosity;
mechanical strength; permeability; corrosion resistance;
application and acoustical resistance.
versatility For extremely fine powders, MKI offers Dynapore
Particle Control Fluidizing MediaTM. PCMTM
media are available in the same flow ranges as
LFM and HFM but with particle barrier meshes as
fine as two microns sintered to the downstream
surface. Consult the factory for more information.
• Fluidized hoppers, • Propellant surface
beds and slides tension devices
• Air film conveyors • Resin and catalyst
• Air bearings beds
• Spargers and diffusers • Filter leaves and
• Transpiration cooling cartridges
media • Particle classification
• Flame and spark screens MARTIN KURZ & CO., INC.
arresters • Vacuum forming and 138 Liberty Avenue
• Flow restricters molding media Mineola, New York USA 11501-3580
• Drying/de-watering Tel: 516-746-7000 • Fax: 516-746-1818
• Pressure snubbers
• Acoustical mufflers media
INTERNET ADDRESS: http://www.mkicorp.com
E-Mail: dynapore@mkicorp.com
WARRANTY NOTE: MKI makes no warranties, express or implied, regarding the information herein, or the products described herein.
Application suitability must be determined by the end user of the products prior to purchase.
 Bulletin No. 401

Fluidizing Media Mechanical Properties

MEDIA Ultimate Tensile Yield Strength @ Elongation, 2 in. Tensile modulus of Thickness (in)
TYPE Strength (psi) 0.2% offset (psi) gauge length (%) elasticity (psi x 106) approximate

LFM-5 40,000 28,500 9.0 13.3 0.054

LFM-10 39,000 27,000 13.5 13.0 0.058

LFM-25 30,000 19,000 14.5 12.7 0.061

LFM-50 25,500 14,250 16.0 11.0 0.068

HFM-50 26,000 19,000 9.0 11.0 0.041

HFM-100 24,000 17,000 11.0 9.7 0.044

HFM-200 18,850 11,250 16.5 8.8 0.050

HFM-400 16,000 7,600 22.5 8.3 0.060

HFM-600 13,900 5,400 24.3 7.6 0.065

Notes
1.) Approximate weight: LFM 2.0 lbs/sq. ft.
HFM 1.5 lbs/sq. ft.

2.) Testing in accordance with ASTM A 370-95a.

3.) All data are approximate or average, and are based on standard AISI T-316 stainless steel construction.

4.) Specifications are subject to change without notice.

5.) Designs should reflect the decreasing yield strength of type 316 stainless steel at temperatures over 400o F.

• Sintered wire mesh laminates

• Sintered powder metal
• Sintered fiber metal

Martin Kurz & Co., Inc.

128 Liberty Avenue • Mineola, N.Y. 11501-3580
Phone: (516) 746-7000 • Fax: (516) 746-1818
E-mail: dynapore@mkicorp.com
 Bulletin No. 402

Installation Recommendations

1.0 Fitting Dynapore LFM & HFM Fluidizing Media:

Generally speaking, Dynapore fluidizing media can be handled as if they were solid stainless steel sheets.
They may be readily cut to size on a power shear, band saw, or nibbler of proper capacity. These media
may also be formed using suitable bend radii. (Please consult factory for recommendations). Dynapore
media may be punched using standard punches and dies. A punch-to-die clearance of 31⁄2% per side is
suggested.

2.0 Welding:

Welding Dynapore sheets together to make larger pieces can be accomplished readily through
butt-welding. After shearing or cutting the media to obtain a clean straight edge, butt the sheet edges
together on top of a copper plate or bar for support and to serve as a heat sink. TIG weld the joint with an
initial setting of around 32 volts and 45 amps. Use a 0.063” diameter 2% thoriated Tungsten electrode and
T-347 filler wire of 0.032” to 0.040” diameter. If cleaning the weld is required, use only a STAINLESS
STEEL wire brush. These media can also be welded using plasma, laser, and electron beam methods.

3.0 Chemical Finishing:

Some applications may require passivation or electropolishing of the media. Dynapore media may be
finished by either of these chemical finishing processes. However, due to variances in bath compositions
and concentrations, residence times may vary. Always test a small sample or test coupon before
proceeding with the production lot. In addition, thorough rinsing is very important.

4.0 Caulking:

Airflow losses must be prevented around the panel edges where the media are clamped between plenum
flanges. An appropriate caulking compound should be applied to seal both upper and lower surfaces of
the media. Where Dynapore media are used to retrofit an existing slide, or in conjunction with another
medium, shimming may be required if variations in media thicknesses are greater than flange adjustment
allowances.

5.0 Air Supply:

To provide optimal operating life, the fluidizing air supply must be of instrument quality, i.e., clean and dry.
Regular replacement of the air supply filters, as well as providing moisture free air, will help insure long
life. In addition, thorough cleaning of the plenum prior to installation will prevent immediate plugging,
assuming the plenum has been properly and adequately sealed.

Martin Kurz & Co., Inc.

128 Liberty Avenue • Mineola, N.Y. 11501-3580
Phone: (516) 746-7000 • Fax: (516) 746-1818
E-mail: dynapore@mkicorp.com
 Bulletin No. 403

Installation Recommendations

In applications where the conveyor is subjected to an intermittent load from dropping powder, a
deflector plate, cross supports and bolting arrangement, as shown in the sketch, are
recommended. The accompanying table gives the support spacing for a range of inside conveyor
widths and air supply pressures.

2 CROSS SUPPORTS CEMENT IN

BEYOND SIDE OF
INLET CHUTE

DEFLECTOR PLATE
FOR ABSORBING
IMPACT OF
BUCKET DROP

W
A
WELD AIR IN

S S 1
⁄4 - 20 cres. screw self
threading
CRES. WASHER

2” TYP
DYNAPORE

1 x 1 x 1/4
SECTION A-A STEEL ANGLE OR EQUIVALENT

WIDTH SPACING OF CROSS SUPPORTS, “S”, Inches

“W” 1 PSIG 2 PSIG 3 PSIG 4 PSIG 5 PSIG 6 PSIG

6 - - - - 6.0 4.5
8 - - 8.5 6.0 6.0 4.5
10 - - 8.0 6.0 6.0 4.5

12 - 10.0 7.0 6.0 6.0 4.5

14 - 9.0 7.0 6.0 6.0 4.5
16 16.0 9.0 7.0 6.0 6.0 4.5

18 15.0 9.0 7.0 6.0 6.0 4.5

20 14.5 9.0 7.0 6.0 6.0 4.5

22 14.5 9.0 7.0 6.0 6.0 4.5

24 14.5 9.0 7.0 6.0 6.0 4.5

Martin Kurz & Co., Inc.

128 Liberty Avenue • Mineola, N.Y. 11501-3580
Phone: (516) 746-7000 • Fax: (516) 746-1818
E-mail: dynapore@mkicorp.com
 Bulletin No. 404

Fluidizing Media Technical Data

AIR FLOW CHARACTERISTICS

The air flow rating values for the 3-layer and 2-layer Dynapore laminates are presented in the following table. The 3-layer
2
laminate covers the air flow range from 5 to 25 SCFM/ft at 2 in. water pressure drop. The 2-layer laminate flows from 50
2
to 400 SCFM/ft at 2 in. water pressure drop.
AIR FLOW RATING

3-LAYER LAMINATE (WEIGHT 2.0 LBS./SQ. FT.) 2-LAYER LAMINATE (WEIGHT 1.5 LBS./SQ. FT.)
AIR FLOW NOMINAL AIR FLOW NOMINAL
PART SCFM/FT.2@P THICKNESS PART SCFM/FT.2@P THICKNESS
NUMBER 2 IN. WATER INCHES NUMBER 2 IN. WATER INCHES

407520 5.0 0.054 401420 50 0.041

401430 100 0.044
401300 10.0 0.058 401440 200 0.050
407530 25.0 0.061 407570 400 0.060

Pressure drop curves for the 3-layer and the 2-layer laminates are given in the following figures for standard pressure and
temperature air entry conditions. For other conditions, flow equations are provided to facilitate pressure drop calculation.
PRESSURE DROP VS AIR FLOW - 3-LAYER DYNAPORE
200
UPSTREAM CONDITIONS
UPSTREAM CONDITIONS
o
1 ATM. 70
70F F
100
80
60
P, PRESSURE DROP, in. water

40

20 401300
LFM-10

407520
LFM-5
10
8 407530
LFM-25
6

2
RATING POINT

1
1 4 8 20 60 100 400 800
2 6 10 40 80 200 600 1000
800
2
G, AIR FLOW, SCFM/ft

Martin Kurz & Co., Inc.

128 Liberty Avenue • Mineola, N.Y. 11501-3580
Phone: (516) 746-7000 • Fax: (516) 746-1818
E-mail: dynapore@mkicorp.com
1
 Fluidizing Media Technical Data

PRESSURE DROP VS AIR FLOW - 2 LAYER DYNAPORE

200
UPSTREAMCONDITIONS
UPSTREAM CONDITIONS
o
1 ATM.
ATM.70
70FF
100
80
60
P, PRESSURE DROP, in. water

40

20
401420
HFM-50 HFM-400
407570
10
8
6 401440
HFM-200

4
401430
HFM-100
2
RATING POINT
1
1 4 8 20 60 100 400 800 2000
2 6 10 40 80 200 600 1000 4000

2
G, AIR FLOW, SCFM/ft

The flow permeability of Dynapore material may be presented in equation form for estimating the flow
characteristics for a variety of conditions and fluids.
For incompressible air flow the equation is:
2
P = AG + BG
2
Where P is pressure drop (in. water column) and G is air flow (SCFM/ft @ 70oF). The constants A (viscous flow
coefficient) and B (inertial flow coefficient) are listed in the table.
For compressible air flow the equation is:
2 2
P = AG + BG
2 2 2
Where P = P - P , and P is the upstream pressure and P is the downstream pressure, (both in in. water column
1 2 1 2
2
absolute. G is air flow (SCFM/ft @ 70oF). The applicable constants, A and B are listed in the table. Note that they are
different than for incompressible flow.

Martin Kurz & Co., Inc.

128 Liberty Avenue • Mineola, N.Y. 11501-3580
Phone: (516) 746-7000 • Fax: (516) 746-1818
E-mail: dynapore@mkicorp.com
2
 Fluidizing Media Technical Data

AIR FLOW EQUATION CONSTANTS

1 2
INCOMPRESSIBLE COMPRESSIBLE
2 2
FLOW (P, IN. WATER (P , IN. WATER
2 2 2
PART SCFM/FT. @P G, SCFM/FT. ) G,SCFM/FT. )
NUMBER 2 IN. WATER
A B, x 10-3 A B

3-LAYER LAMINATES

407520 5.0 0.375 4.95 300.0 4.40

401300 10.0 0.181 1.90 147.0 1.45
407530 25.0 0.0697 0.415 58.0 0.33

2-LAYER LAMINATES

401420 50.0 0.0295 0.210 24.2 0.165

401430 100.0 0.0130 0.070 10.8 0.054
401440 200.0 0.0050 0.025 4.60 0.0177
407570 400.0 0.00192 0.0077 1.78 0.0057

1. Incompressible - upstream conditions: 70oF, 1 Atm.

2. Compressible - upstream conditions: 70oF

When estimating the flow permeability for air at temperatures other than 70oF, or for other fluids the more general gas flow
equations are applicable.

For incompressible gas (or liquid) the equation is:

2
P = AV + BV
3
Where  is absolute viscosity (in centipoise, CP)  is specific weight (lb/ft ), P is pressure drop (in. water) and V is flow
2
(CFM/ft ). The constants for A and B are obtained from the gas flow table.
For compressible gas the equation is:

2 T T 2
P = A G + B G
M M
2 2 2 2
Where P = P - P and P is the upstream pressure, P is downstream (in. water column), G is flow (SCFM/ft referred
1 2 1 2
to 70F, 1 Atm.), T is absolute temperature (oR), M is molecular weight, and  is viscosity (centipoise), the constants A and
B are given in the gas flow table for compressible flow.

Martin Kurz & Co., Inc.

128 Liberty Avenue • Mineola, N.Y. 11501-3580
Phone: (516) 746-7000 • Fax: (516) 746-1818
E-mail: dynapore@mkicorp.com
3
 Fluidizing Media Technical Data

GAS FLOW EQUATION CONSTANTS

GAS OR LIQUID GAS

FLOW INCOMPRESSIBLE COMPRESSIBLE
2 2 2
PART SCFM/FT. @P (P, IN. WATER (P , IN. WATER
2 2
NUMBER 2 IN. WATER V, CFM/FT. ) G,SCFM/FT. )

A B, x 10-3 A B, x 10-3
3-LAYER LAMINATES

407520 5.0 20.60 66.10 900.0 241.00

401300 10.0 9.92 25.40 441.0 79.40
407530 25.0 3.82 5.54 174.0 18.10

2-LAYER LAMINATES

401420 50.0 1.616 2.80 72.6 9.00

401430 100.0 0.712 0.934 32.4 2.90
401440 200.0 0.274 0.336 13.8 0.969
407570 400.0 0.105 0.103 5.34 0.312

SAMPLE CALCULATIONS
To illustrate the use of the flow equations, sample calculations are presented for the four equations for Dynapore Part
2
No. 401300 (10 SCFM/ft @ 2 in. water) for the following conditions:
INCOMPRESSIBLE AIR FLOW
2
Air Flow, G = 100 SCFM/ft
Upstream Temperature = 70oF From Air Flow Table:
Upstream Pressure = 1 Atm. A = 0.181
2 -3
P = AG + BG B = 1.90 x 10
-3 2
P = 0.181 (100) + 1.90 x 10 (100)
P = 37.1 in. water
COMPRESSIBLE AIR FLOW
2
Air Flow, G = 250 SCFM/ft Subscripts:
Upstream Temperature = 70oF 0 = Standard
Upstream Pressure, P = 814.4 in. water absolute 1 = Upstream
1
2 2 2 = Downstream
P = AG + BG
2 2
P = 147(250) + 1.45(250)
2 2 2
P = 127,375 = P 1 - P2 From Air Flow Table:

2 2 A = 147
P = (814.4) - 127,375 = 732.0 in. water B = 1.45
P = P - P = 814.4 - 732.0 = 82.4 in. water
1 2

Martin Kurz & Co., Inc.

128 Liberty Avenue • Mineola, N.Y. 11501-3580
Phone: (516) 746-7000 • Fax: (516) 746-1818
E-mail: dynapore@mkicorp.com
4
 Fluidizing Media Technical Data

INCOMPRESSIBLE GAS FLOW (OR LIQUID)

Upstream Air Conditions:

P = 814.4 in. water absolute

1
T = 200oF + 460o = 660oR
1 2
V = 62 CFM/ft
1 P T
 , specific weight =  1 x 0 = 0.07493(814.4) (70 + 460) = 0.1203 lb./ft3
1 0 P T (407.2) (660)
0 1
 = viscosity = 0.02127 centipoise @ 660 Ro
1
2
P = A  V + B  V From Gas Table:
1 1 1 1 -3 2
P = 9.92(0.02127)62 + 25.4 x 10 (0.1203)(62) A = 9.92
-3
P = 24.8 in. water B = 25.4 x 10

COMPRESSIBLE GAS FLOW

Upstream Air Conditions:

P = 814.4 in. water absolute

1
T = 200oF + 460o = 660oR
1 2
V = 248 CFM/ft
1
P T
G=V 1 x 0 = 248(814.4) (70 + 460) = 398.3 SCFM/ft2
1P T (407.2) (660)
0 1
From Gas Table:
P T A = 441
 , specific weight =  1 x 0 = 0.07493(814.4) (70 + 460) = 0.1203 lb./ft3 -3
1 0 P T (407.2) (660) B = 79.4 x 10
0 1

 = viscosity = 0.02127 centipoise

1
M = Molecular weight = 28.97

2 T T 2
P = A  1 G + B 1 G
1M M VISCOSITY OF AIR
2 441(0.02127)(660)(398.3) 79.4 x 10-3 (660) (398.3)2 TEMPERATURE VISCOSITY
P = +
28.97 28.97 o
F R
o
CENTIPOISE
-60 400 0.0145
2 2 2 70 530 0.0182
P = 372,086 = P - P
1 2
140 600 0.0200
340 800 0.0250
2
P = (814.4) - 372,086 = 539.6 in. water
2 540 1000 0.0285
P = P - P = 814.4 - 539.6 = 274.8 in. water 1040 1500 0.0370
1 2

Martin Kurz & Co., Inc.

128 Liberty Avenue • Mineola, N.Y. 11501-3580
Phone: (516) 746-7000 • Fax: (516) 746-1818
E-mail: dynapore@mkicorp.com
5