Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
136 views

Minivna Tiny: Hardware Manual For

The miniVNA Tiny is a handheld vector network analyzer with an extraordinary frequency range of 1MHz to 3GHz. It has S11 and S21 measurement capabilities, integrated Smith chart software, and supports Windows, Linux, and Mac operating systems. Safety instructions must be strictly followed when using the device in hazardous environments.

Uploaded by

richardvmoreno
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
136 views

Minivna Tiny: Hardware Manual For

The miniVNA Tiny is a handheld vector network analyzer with an extraordinary frequency range of 1MHz to 3GHz. It has S11 and S21 measurement capabilities, integrated Smith chart software, and supports Windows, Linux, and Mac operating systems. Safety instructions must be strictly followed when using the device in hazardous environments.

Uploaded by

richardvmoreno
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Hardware Manual for miniVNA Tiny

Congratulation on your choice of mini RADIO SOLUTIONS Vector Network Analyzer!


The new miniVNA Tiny is a new extraordinary PC based, handheld Vector Network
Analyzer, the first with the very large frequency range from 1MHz up to 3GHz!

Safety
Please carefully read the safety instruction included in this manual.
The software for miniVNA Tiny is continuously under developement.
For the latest software and updates, visit www.miniradiosolutions.com

Specifications
• Frequency range 1-3000 MHz
• Calibration using open-short-load for accurate results
• Range of Z from 1 to 1000 ohm
• Two ports VNA with S11 and S21; displayed and save results
• RF Generator with output power of -6dBm @ 500 MHz
• Low power consumption, 370mA @ 5 V
• SMA connectors for better isolation
• Dynamic range up to 70 dB @ 500 MHz
• Boot loader for future firmware upgrades
• User friendly interface for PC: Windows, Linux and Mac
• Android Mobile Phone software
• Integrated Smith chart in software
• Export data in several formats – JPEG, EXCEL, ZPLOT, S2P, PDF
•

Basic Carton Content:


• miniVNA Tiny
• USB Cable (miniUSB )
• this Manual

Caution!
Safety Instructions – which must be strictly observed.
Hazardous Environments:
Do not operate the analyzer in hazardous environments. This equipment is intended to be used for
maintenance, research, evaluation, simulation and other analytical or scientific applications in areas such as
public utilities, hospitals, universities, laboratories, automotive service centers and electronic repair shops. We
are not liable for any problems resulting from the use of the analyzer in hazardous environments and misuse.
Warning!
The use of this device may be subject to national restrictions or regulations. Check your local authority or dealer
before purchasing and using this product.

Warning
RF inputs are protected against overload up to 25VDC and 10mW RF. Input power exceeding those limits my
cause permanent damage to the unit. Warranty is voided for damaged units due to overload.

www.miniradiosolutions.com support@miniradiosolutions.com

07276 / 96680 www.wimo.com info@wimo.com  WiMo 2014 1


Hardware Manual for miniVNA Tiny

Connections RF side
DUT Port ("device under test") is typically
connected to the antenna under test when the
analyzer is set by the software to work in Reflection
mode.
CAUTION! Not apply to this port DC signals over
25Vdc and RF signals over 10mW (voids Warranty)

DET Port ("detector") is used to check filters and


amplifiers when the analyzer is set by the software
to work in Transmission mode .
CAUTION! Not apply to this port DC signal over
25Vdc and RF signals over 10mW (voids
Warranty).

Connections USB side


The USB connection is required for power and
communication to the PC via USB cable (included
in the package).
CAUTION!
DO NOT Use Any other Voltage Source.
When connecting the analyzer via USB first time,
FTDI drivers are to be installed. Unless this driver is
not already installed on your system, a popup
window will open and ask for the new driver, which
is downloadable to the FTDI web site:
http://www.ftdichip.com/Drivers/VCP.htm

LED Placement and meaning. LED 2


Led 1, green: Analog POWER ON
Led 2, orange: blinks during serial communication

LED 1

Suggested Option:
CALIBRATION KIT, containing SMA open / short /
50Ohm termination
part no. 21010.SMA

www.miniradiosolutions.com support@miniradiosolutions.com

07276 / 96680 www.wimo.com info@wimo.com  WiMo 2014 2

You might also like