The document describes the operation and diagnosis of a chime warning/reminder system in a vehicle. It has three main functions: fastening seat belts, headlights left on, and key left in ignition. It provides testing steps to diagnose issues with each function, such as checking for continuity and voltage. The removal and installation of related components like the chime, seat belt buckle, and headlight switch are also outlined.
The document describes the operation and diagnosis of a chime warning/reminder system in a vehicle. It has three main functions: fastening seat belts, headlights left on, and key left in ignition. It provides testing steps to diagnose issues with each function, such as checking for continuity and voltage. The removal and installation of related components like the chime, seat belt buckle, and headlight switch are also outlined.
The document describes the operation and diagnosis of a chime warning/reminder system in a vehicle. It has three main functions: fastening seat belts, headlights left on, and key left in ignition. It provides testing steps to diagnose issues with each function, such as checking for continuity and voltage. The removal and installation of related components like the chime, seat belt buckle, and headlight switch are also outlined.
The document describes the operation and diagnosis of a chime warning/reminder system in a vehicle. It has three main functions: fastening seat belts, headlights left on, and key left in ignition. It provides testing steps to diagnose issues with each function, such as checking for continuity and voltage. The removal and installation of related components like the chime, seat belt buckle, and headlight switch are also outlined.
These are the conditions that have to be met for INTRODUCTION the headlamps on, chime function to work: • Headlamps ON. WARNING: ON VEHICLES EQUIPPED WITH AN AIR- • Driver’s door open. BAG, REFER TO THE AIRBAG PORTION OF THIS • Key removed from the ignition switch. SECTION FOR STEERING WHEEL OR SWITCH Chime should sound until headlamps are turned REMOVAL AND INSTALLATION PROCEDURES. off or driver’s door is closed. If these conditions are met and there is still a The seat belt reminder system uses both visual problem with the system, replace the instrument and audible signals. A combined seat belt and key cluster. Refer to Group 8E-Instrument Panel and reminder chime with a red light on the instrument Systems, Instrument Cluster Removal and Installa- panel. tion. The system will always illuminate the seat belt reminder lamp for four to eight seconds when the KEY LEFT IN IGNITION SWITCH ignition switch is turned to the ON position. The To test the key left in ignition function, insert key CHIME will sound during the same time interval if into the ignition and open the driver’s door. Chime the driver’s seat belt is not fastened. Passenger belts should sound until key is removed from ignition or are not connected to the system. driver’s door is closed. The chime will activate if the drivers door is If these conditions are met and there is still a opened and: problem with the system, replace the instrument • The key is in the ignition switch, with the igni- cluster. Refer to Group 8E-Instrument Panel and tion switch in either the OFF or accessory (ACC) Systems, Instrument Cluster Removal and Installa- position. tion. • The head lamps are ON. The chime is integral to the instrument cluster. CHIME SYSTEM CONDITIONS
DIAGNOSIS AND TESTING NO TONE WHEN IGNITION SWITCH IS TURNED ON
AND DRIVERS SEAT BELT IS UNBUCKLED FASTEN SEAT BELTS (1) Using an ohmmeter, with the seat belt fully To test the fasten seat belts function, turn the igni- retracted, check for continuity to ground at Pin 25 of tion switch to the ON position with the driver’s seat the cluster harness connector. If OK, go to step 2. If belt unbuckled and fully retracted. The seat belt not OK, repair as necessary. warning lamp should light for four to eight seconds (2) Using voltmeter, check for battery feed at Pin and the tone should sound three to five times. 21 of the cluster harness connector. Check for igni- If the lamp does not light, check the connection at tion feed at Pin 15 of the cluster harness connector. the seat belt retractor and the LED in the instru- If not OK, repair as necessary. ment cluster. Replace as necessary. 8U - 2 CHIME WARNING/REMINDER SYSTEM PL DIAGNOSIS AND TESTING (Continued) NO FASTEN SEAT BELT LAMP WHEN IGNITION in ignition and parking lamps are OFF. If ground is SWITCH IS ON still present check door switch, key in switch, head- (1) Check for battery feed at cluster harness con- lamp switch and repair as necessary. nector Pin 21. (2) Check for ignition feed at cluster harness con- REMOVAL AND INSTALLATION nector Pin 15. Repair as necessary.
NO TONE WHEN HEADLAMPS ARE ON AND
CHIME The functions previously performed by the chime DRIVERS DOOR IS OPEN module are now part of the smart cluster. There is no (1) Check left door jamb switch for good ground servicable part of the instrument cluster chime func- when drivers door is open. tion. Replacement of the instrument cluster is neces- (2) Check for ground at Pin 10. sary. Refer to Group 8E-Instrument Panel and (3) Check for battery feed at cluster harness con- Systems, Instrument Cluster Removal and Installa- nector Pin 21. tion. (4) Check for NO voltage at Pin 14. Ignition volt- age must not be present for the chime to work. SEAT BELT BUCKLE (5) Check headlamp switch. Refer to Group 23-Body, Front Seat Belt Buckle Removal and Installation. NO TONE WHEN KEY IS LEFT IN IGNITION AND DRIVERS DOOR IS OPEN HEADLAMP SWITCH (1) Check for continuity to ground at Pin 23 of the Refer to Group 8J-Turn Signal and Hazard Warn- cluster harness connector. If OK, go to Step 3. If not ing Systems, Multi-Function Switch Removal and OK, repair as necessary. Installation. (2) Using voltmeter, check for battery feed at Pin 21 of the cluster harness connector. Check for NO KEY-IN SWITCH ignition feed at Pin 15 of the cluster harness connec- The Key-in switch is built into the ignition switch tor. If OK, go to Step 3. If not OK, repair as neces- assembly. Should the Key-in switch require service, sary. the ignition switch assembly must be replaced. Refer (3) Open driver’s door and ensure the ignition key to Group 8D-Ignition System, Ignition Switch is in the OFF or ACC position. Check for continuity Removal and Installation. to ground at Pin 10 of the cluster harness connector. If ground OK, replace cluster printed circuit board. If no ground, check key-in switch or door switch wiring and repair as necessary.
CHIMES CONTINUE WHEN HEADLAMPS ARE
TURNED OFF AND/OR KEY IS REMOVED FROM IGNITION Check for ground at Pin 10. If grounded the chime should activate. Make sure the door is closed, key is