Extrudex Aluminum Catalogue PDF

http://www.extrudex.
com
LOCATIONS:
Extrudex Aluminum Corp. Extrudex Aluminum Inc. Extrudex Aluminum (Quebec) Inc.
411 Chrislea Road 12051 Mahoning Ave 770 Chemin Oliver
Woodbridge, Ontario Box 697 Bernieres, Quebec
Canada North Jackson, Ohio Canada
L4L 8N4 USA 44451 G7A 2N2
Tel: (416) 745-4444 Tel: (330) 538-4444 Tel: (418) 831-4444
Fax: (416) 745-0925 Tel: (330) 538-4450 Fax: (418) 831-7400
Toll Free: 1-800-668-7210 Toll Free: 1-800-430-0006 Toll Free: 1-800-704-4244
Container Size:
7", 8", 10" and 13" 8" and 10" 7" and 8"
Stretching Capacity:
25 Lbs/Ft 15 Lbs/Ft
Alloys:
6063, 6061, 6351, 6005 6063, 6061, 6351, 6005 6063, 6061, 6005
Chemical composition and tolerance charts are included with permission from
"The Aluminum Association Inc., 900 19th St., N.W. Washington, D.C. 20006"
Revised on: April 18, 2019

http://www.extrudex.com
Rectangular Bars
Square Edges
Die Number Dim. (W) Dim. (T) WT. (LBS/FT) WT. (KGS/MT) Toronto Ohio
S-2133 0.437 0.312 0.161 0.240 à
S-4481 0.500 0.125 0.073 0.109 P
S-2979 0.500 0.187 0.110 0.164 P P
S-23972 0.500 0.250 0.148 0.210 P
S-2134 0.500 0.375 0.221 0.329 P
S-6347 0.625 0.125 0.092 0.137 P
S-26175 0.625 0.250 0.184 0.274 P
S-2135 0.625 0.375 0.276 0.411 P
S-23105 0.625 0.500 0.369 0.548 P
S-5567 0.750 0.094 0.084 0.125 P
S-4642 0.750 0.125 0.111 0.165 P P
S-2381 0.750 0.187 0.165 0.246 P P
S-22340 0.750 0.250 0.221 0.329 P
S-27823 0.750 0.375 0.332 0.494 P
S-4767 0.750 0.500 0.442 0.659 P P
S-5563 0.875 0.120 0.124 0.184 P
S-22060 0.875 0.125 0.129 0.192 P
S-4525 1.000 0.123 0.145 0.216 P
S-2234 1.000 0.125 0.148 0.220 P P
S-4526 1.000 0.185 0.218 0.325 P
S-2231 1.000 0.187 0.221 0.329 P P
S-2125 1.000 0.250 0.295 0.439 P P
S-22329 1.000 0.312 0.368 0.548 P P
S-2222 1.000 0.375 0.443 0.659 P P
S-2224 1.000 0.500 0.590 0.878 P P
S-2491 1.000 0.625 0.738 1.098 P P
S-2444 1.000 0.750 0.885 1.317 P P
S-24127 1.125 0.100 0.133 0.197 P
S-5598 1.125 0.165 0.218 0.324 P
S-25702 1.125 0.750 0.995 1.481 P
S-12343 1.125 1.000 1.327 1.975 P
S-4900 1.250 0.123 0.182 0.270 P
S-2351 1.250 0.125 0.184 0.274 P P
(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019
Rectangular Bars
Square Edges
S-4527 1.250 0.182 0.269 0.400 P
S-3513 1.250 0.188 0.277 0.412 P P
S-22148 1.250 0.200 0.295 0.439 P
S-2349 1.250 0.250 0.369 0.549 P P
S-4766 1.250 0.375 0.553 0.824 P P
S-2579 1.250 0.500 0.738 1.098 P P
S-2578 1.250 0.750 1.107 1.647 P P
S-12392 1.250 1.000 1.475 2.195 P P
S-2635 1.375 0.220 0.344 0.515 P
S-22342 1.375 1.000 1.622 2.414 P
S-2327 1.437 0.250 0.424 0.631 P
S-4674 1.500 0.123 0.218 0.325 P
S-2254 1.500 0.125 0.222 0.330 P P
S-4600 1.500 0.185 0.328 0.488 P P
S-2181 1.500 0.187 0.332 0.494 P P
S-2076 1.500 0.250 0.443 0.659 P P
S-2229 1.500 0.375 0.664 0.988 P P
S-2396 1.500 0.500 0.885 1.317 P P
S-4969 1.500 0.750 1.327 1.976 P P
S-4654 1.500 1.000 1.770 2.634 P P
S-4676 1.500 1.250 2.213 3.293 P P
S-26762 1.550 1.300 2.377 3.538 P
S-20806 1.625 0.250 0.479 0.713 P
S-2916 1.750 0.125 0.258 0.384 P P
S-4889 1.750 0.185 0.382 0.569 P
S-4801 1.750 0.188 0.388 0.577 P P
S-2398 1.750 0.250 0.517 0.769 P P
S-9312 1.750 0.438 0.904 1.345 P
S-2331 1.750 0.500 1.033 1.537 P P
S-9964 1.750 0.750 1.548 2.304 P P
S-24252 1.750 1.000 2.065 3.073 P
S-23324 1.750 1.375 2.835 4.220 P
S-2233 2.000 0.125 0.295 0.439 P P
Rectangular Bars
Square Edges
S-5269 2.000 0.185 0.437 0.650 P
S-2230 2.000 0.187 0.441 0.656 P P
S-2226 2.000 0.250 0.590 0.878 P P
S-2223 2.000 0.375 0.885 1.317 P P
S-30283 2.000 0.438 1.033 1.538 P
S-2221 2.000 0.500 1.180 1.756 P P
S-23874 2.000 0.625 1.475 2.195 P P
S-2436 2.000 0.750 1.770 2.634 P P
S-7238 2.000 1.000 2.360 3.512 P P
S-12342 2.000 1.125 2.655 3.951 P
S-22772 2.000 1.250 2.950 4.390 P P
S-4659 2.000 1.500 3.540 5.268 P P
S-5215 2.250 0.185 0.491 0.731 P
S-4090 2.250 0.188 0.499 0.743 P
S-2615 2.250 0.250 0.664 0.988 P P
S-21464 2.250 0.375 0.995 1.481 P P
S-24517 2.500 0.125 0.369 0.549 P
S-5268 2.500 0.185 0.546 0.813 P
S-4091 2.500 0.188 0.555 0.826 P P
S-2455 2.500 0.250 0.738 1.098 P P
S-16069 2.500 0.345 1.018 1.514 P
S-2325 2.500 0.375 1.107 1.647 P P
S-4651 2.500 0.500 1.475 2.195 P P
S-13590 2.500 0.750 2.212 3.292 P à
S-4655 2.500 1.000 2.950 4.390 P P
S-19141 2.500 1.250 3.687 5.487 P P
S-4660 2.500 1.500 4.425 6.585 P P
S-23922 2.500 2.000 5.900 8.780 P
S-25964 2.500 2.250 6.637 9.877 P
S-5206 2.750 0.125 0.406 0.604 P
S-21463 2.750 0.250 0.811 1.207 P P
S-2490 2.750 0.375 1.217 1.811 P
S-26761 2.750 2.000 6.490 9.658 P
Rectangular Bars
Square Edges
S-20793 2.750 2.375 7.707 11.469 P
S-20794 2.875 2.500 8.481 12.621 P
S-2155 2.937 0.081 0.281 0.418 P
S-2225 3.000 0.125 0.443 0.659 P P
S-2220 3.000 0.187 0.662 0.985 P P
S-2168 3.000 0.250 0.885 1.317 P P
S-2218 3.000 0.375 1.328 1.976 P P
S-2216 3.000 0.500 1.770 2.634 P P
S-15161 3.000 0.625 2.212 3.292 P
S-2313 3.000 0.750 2.655 3.951 P P
S-21121 3.000 0.875 3.097 4.609 P
S-4656 3.000 1.000 3.540 5.268 P P
S-15281 3.000 1.250 4.425 6.585 P P
S-4769 3.000 1.500 5.310 7.902 P P
S-20398 3.000 1.750 6.195 9.219 P P
S-7354 3.000 2.000 7.080 10.536 P P
S-21519 3.000 2.250 7.965 11.853 P
S-26187 3.000 2.500 8.850 13.170 P
S-8399 3.375 0.188 0.748 1.113 P P
S-16731 3.375 0.250 0.995 1.481 P
S-20820 3.375 1.875 7.467 11.112 P
S-6698 3.500 0.095 0.392 0.583 P
S-3469 3.500 0.187 0.773 1.150 P P
S-2450 3.500 0.250 1.033 1.537 P P
S-14971 3.500 0.375 1.549 2.304 P P
S-22691 3.500 0.500 2.065 3.075 P P
S-2314 3.500 0.625 2.582 3.842 P
S-22164 3.500 0.750 3.097 4.609 P P
S-22165 3.500 1.000 4.130 6.146 P P
S-22836 3.500 1.500 6.195 9.219 P P
S-22166 3.500 2.000 8.260 12.292 P
S-22433 3.500 2.000 8.260 12.292 P
S-26185 3.500 2.500 10.325 15.365 P
Rectangular Bars
Square Edges
S-20800 3.625 0.312 1.334 1.986 P
S-20821 3.625 1.875 8.020 11.935 P
S-20795 3.750 2.625 11.615 17.286 P
S-4274 4.000 0.125 0.590 0.878 P P
S-2219 4.000 0.187 0.883 1.314 P P
S-2215 4.000 0.250 1.180 1.756 P P
S-2217 4.000 0.375 1.770 2.634 P P
S-2171 4.000 0.500 2.360 3.512 P P
S-21375 4.000 0.625 2.950 4.390 P P
S-4653 4.000 0.750 3.540 5.268 P P
S-4657 4.000 1.000 4.750 7.068 P P
S-18708 4.000 1.250 5.900 8.780 P P
S-17122 4.000 1.500 7.080 10.536 P P
S-12195 4.000 2.000 9.440 14.050 P P
S-26186 4.000 2.500 11.800 17.500 P
S-17140 4.000 3.000 14.160 21.072 P
S-20302 4.250 0.188 0.942 1.402 P
S-12796 4.250 1.000 5.015 7.463 P
S-20804 4.250 2.250 11.284 16.792 P
S-11474 4.429 0.630 3.292 4.899 P
S-21680 4.500 0.125 0.664 0.987 P
S-6118 4.500 0.187 0.994 1.479 P P
S-22085 4.500 0.250 1.327 1.975 P
S-12912 4.500 3.000 15.930 23.706 P
S-8915 4.625 0.158 0.863 1.284 P
S-8916 4.625 0.187 1.021 1.519 P
S-16645 4.700 1.000 5.546 8.253 P
S-2311 4.750 0.250 1.402 2.086 P P
S-15823 5.000 0.125 0.737 1.097 P
S-3654 5.000 0.182 1.074 1.598 P
S-3655 5.000 0.220 1.298 1.931 P
S-3296 5.000 0.250 1.475 2.195 P P
S-16638 5.000 0.375 2.212 3.292 P P
Rectangular Bars
Square Edges
S-4768 5.000 0.500 2.950 4.390 P P
S-21683 5.000 0.625 3.687 5.487 P
S-65 5.000 0.750 4.425 6.585 P
S-23758 5.000 0.750 4.425 6.585 P
S-12198 5.000 1.000 5.900 8.780 P P
S-25582 5.000 1.500 8.850 13.170 P P
S-13042 5.000 2.000 11.800 17.560 P
S-24766 5.000 2.500 14.750 21.950 P
S-2504 5.040 0.750 4.460 6.636 P
S-21469 5.250 0.190 1.177 1.751 P
S-2755 5.375 0.250 1.586 2.360 P
S-20480 5.500 0.160 1.037 1.544 P
S-22339 5.500 0.188 1.220 1.816 P
S-20634 5.500 0.250 1.622 2.419 P P
S-13218 5.500 0.375 2.434 3.621 P
S-2757 5.875 0.250 1.733 2.579 P
S-2232 6.000 0.250 1.770 2.634 P P
S-4650 6.000 0.375 2.655 3.951 P P
S-4652 6.000 0.500 3.540 5.268 P P
S-4800 6.000 0.750 5.310 7.902 P P
S-4658 6.000 1.000 7.080 10.530 P P
S-17121 6.000 1.250 8.850 13.170 P P
S-13077 6.000 1.500 10.620 15.804 P P
S-17125 6.000 2.000 14.160 21.072 P
S-20819 6.000 2.250 15.930 23.706 P
S-26514 6.000 2.500 17.700 26.340 P
S-18276 6.000 3.000 21.240 31.608 P
S-2489 6.125 0.375 2.710 4.032 P
S-26687 6.250 0.500 3.687 5.487 P
S-17443 6.375 1.625 12.224 18.191 P
S-21682 6.500 1.000 7.670 11.414 P
S-5070 6.750 0.250 1.992 2.964 P P
S-125 6.750 0.500 3.982 5.926 P
Rectangular Bars
Square Edges
S-24451 7.000 0.500 4.130 6.146 P
S-66 7.000 0.750 6.195 9.219 P
S-24205 7.000 1.000 8.260 12.292 P
S-22245 7.250 0.500 4.277 6.365 P
S-18313 7.250 0.750 6.416 9.548 P
S-22732 7.375 0.375 3.263 4.856 P
S-29813 8.000 0.175 1.652 2.458 P
S-9001 8.000 0.187 1.769 2.633 P
S-12196 8.000 0.250 2.360 3.510 P
S-15198 8.000 0.250 2.360 3.512 P
S-12569 8.000 0.375 3.540 5.268 P P
S-12197 8.000 0.500 4.720 7.020 P P
S-9604 8.000 0.750 7.080 10.536 P P
S-16129 8.000 0.875 8.260 12.292 P
S-5830 8.000 1.000 9.439 14.046 P P
S-17419 8.000 1.250 11.800 17.560 P
S-9350 8.000 1.625 15.340 22.828 P
S-20788 8.000 1.750 16.520 24.584 P
S-10914 8.000 2.000 18.880 28.096 P
S-17579 8.250 0.250 2.434 3.621 P
S-26441 8.380 0.250 2.472 3.679 P
S-20282 8.500 0.188 1.885 2.805 P
S-21681 8.500 0.375 3.760 5.596 P
S-23684 8.500 0.500 5.015 7.463 P
S-10170 8.504 0.394 3.950 5.879 P
S-13660 9.000 0.250 2.655 3.951 P
S-18312 9.000 0.750 7.965 11.853 P
S-20813 9.125 1.875 20.189 30.044 P
S-26922 9.500 0.750 8.407 12.511 P
S-15448 10.000 0.250 2.950 4.390 P P
S-17932 10.000 0.375 4.425 6.585 P
S-23769 10.000 0.500 5.900 8.780 P P
S-22104 10.000 0.750 8.850 13.170 P P
Rectangular Bars
Square Edges
S-16095 10.000 1.000 11.800 17.560 P P
S-8792 12.000 0.250 3.540 5.268 P P
S-12570 12.000 0.375 5.310 7.902 P
S-23980 12.000 0.500 7.080 10.536 P P
S-20799 12.000 0.625 8.850 13.170 P
S-20792 12.500 0.250 3.687 5.487 P

Rectangular Bars
Full Round Edges
S-4276 0.703 0.312 0.234 0.348 P
S-4922 0.750 0.125 0.111 0.165 P P
S-21963 0.750 0.188 0.157 0.234 P
S-21964 0.750 0.250 0.205 0.306 P
S-2299 1.000 0.250 0.280 0.417 P P
S-23745 1.125 0.125 0.162 0.241 P
S-24936 1.250 0.375 0.518 0.770 P
S-2250 1.375 0.375 0.572 0.851 P
S-13825 1.500 0.125 0.217 0.323 P
S-7348 1.500 0.156 0.270 0.402 P
S-2174 1.500 0.250 0.427 0.635 P P
S-13141 1.500 0.500 0.822 1.223 P
S-13822 1.750 0.156 0.316 0.471 P
S-2202 1.750 0.750 1.407 2.094 P
S-2173 2.000 0.125 0.291 0.433 P
S-13823 2.000 0.156 0.363 0.540 P P
S-10077 2.000 0.188 0.434 0.646 P P
S-2269 2.000 0.250 0.575 0.856 P P
S-2266 2.000 0.375 0.850 1.265 P P
S-15348 2.000 0.500 1.117 1.662 P
S-14285 2.000 0.500 1.117 1.662 P
S-13824 2.250 0.219 0.569 0.846 P
S-26688 2.340 0.205 0.555 0.827 P
S-2329 2.500 0.250 0.722 1.074 P P
S-29992 2.500 0.312 0.896 1.333 P
S-29993 2.500 0.500 1.412 2.101 P
S-2175 3.000 0.250 0.870 1.295 P P
S-2267 3.000 0.375 1.292 1.922 P P
S-5424 3.000 0.500 1.706 2.539 P P
S-9489 3.000 1.000 3.286 4.891 P
S-2421 3.500 0.250 1.017 1.513 P
S-29994 3.500 0.312 1.264 1.881 P
S-29995 3.500 0.500 2.002 2.979 P
Rectangular Bars
Full Round Edges
S-2887 3.688 0.125 0.540 0.803 P
S-2298 4.000 0.250 1.165 1.734 P P
S-2248 4.000 0.375 1.735 2.582 P P
S-5016 4.000 0.500 2.296 3.417 P P
S-5423 4.000 1.000 4.466 6.646 P
S-13987 4.500 0.375 1.956 2.910 P
S-2302 5.000 0.250 1.460 2.172 P P
S-2341 5.000 0.375 2.177 3.239 P P
S-27107 5.000 0.500 2.887 4.269 P
S-2172 6.000 0.250 1.755 2.611 P P
S-2268 6.000 0.375 2.620 3.899 P P
S-5419 6.000 0.500 3.476 5.173 P P
S-22055 6.000 0.750 5.168 7.690 P
S-5422 6.000 1.000 6.826 10.150 P
S-13669 6.500 0.500 3.772 5.613 P
S-4952 7.000 0.250 2.050 3.050 P
S-12466 7.000 0.500 4.067 6.052 P
S-29769 8.000 0.250 2.344 3.489 P
S-5420 8.000 0.375 3.505 5.215 P
S-5421 8.000 0.500 4.656 6.929 P P
S-5693 8.000 1.000 9.186 13.669 P P
S-5829 10.000 0.375 4.390 6.532 P
S-6875 10.000 0.500 5.836 8.685 P P

Square Bars
Die Number Dim. (W) WT. (LBS/FT) WT. (KGS/MT) Toronto Ohio
S-4528 0.295 0.103 0.153 P
S-12321 0.375 0.166 0.247 P P
S-2572 0.500 0.295 0.439 P P
S-2203 0.625 0.461 0.686 P P
S-2566 0.750 0.664 0.988 P P
S-2382 1.000 1.180 1.756 P P
S-4763 1.250 1.843 2.743 P P
S-14441 1.375 2.231 3.320 P
S-4661 1.500 2.655 3.951 P P
S-21815 1.625 3.116 4.637 P
S-14092 1.750 3.614 5.377 P P
S-3132 2.000 4.720 7.023 P P
S-4770 2.500 7.375 10.970 P P
S-4662 3.000 10.620 15.800 P P
S-24121 3.500 14.455 21.511 P
S-12408 4.000 18.880 28.096 P

Round Bars
Rods
Die Number Dim. (D) WT. (LBS/FT) WT. (KGS/MT) Toronto Ohio
S-5706 0.312 0.090 0.134 P P
S-2333 0.375 0.130 0.193 à à
S-7766 0.438 0.178 0.265 P à
S-2162 0.500 0.231 0.344 P à
S-16303 0.562 0.293 0.436 P
S-3651 0.625 0.362 0.539 à à
S-21809 0.687 0.437 0.651 à
S-24767 0.687 0.437 0.651 P
S-4758 0.750 0.522 0.776 P à
S-2632 0.775 0.557 0.829 P
S-3652 0.812 0.611 0.909 P à
S-22032 0.840 0.654 0.973 P
S-4771 0.875 0.709 1.055 P
S-9515 0.875 0.709 1.055 à à
S-9514 0.938 0.814 1.212 P
S-6980 0.995 0.918 1.366 à
S-2845 1.000 0.926 1.378 P
S-9599 1.000 0.926 1.378 à à
S-12193 1.062 1.045 1.556 à
S-4772 1.125 1.173 1.745 P à
S-13376 1.125 1.173 1.745 à
S-8958 1.188 1.307 1.946 P
S-2187 1.250 1.448 2.155 à à
S-17999 1.313 1.598 2.378 P
S-4759 1.375 1.751 2.606 à à
S-26465 1.385 1.778 2.646 P
S-29039 1.438 1.916 2.852 P
S-3653 1.460 1.975 2.939 P
S-2500 1.500 2.085 3.102 P à
S-30934 1.500 2.085 3.103 à
S-11049 1.562 2.261 3.365 à à
Round Bars
Rods
Die Number Dim. (D) WT. (LBS/FT) WT. (KGS/MT) Toronto Ohio
S-6851 1.625 2.447 3.642 P à
S-26466 1.725 2.758 4.104 P
S-4760 1.750 2.838 4.223 à à
S-12194 1.812 3.043 4.528 à à
S-4761 1.875 3.258 4.848 P à
S-4663 2.000 3.708 5.518 à à
S-9257 2.125 4.185 6.229 P à
S-4762 2.250 4.692 6.982 à à
S-26904 2.375 5.228 7.779 à
S-26467 2.425 5.450 8.110 P
S-26750 2.438 5.509 8.198 à
S-4856 2.500 5.793 8.620 à à
S-21376 2.625 6.386 9.503 P
S-4664 2.750 7.008 10.430 à à
S-11048 2.875 7.660 11.400 à
S-4665 3.000 8.341 12.410 P à
S-12344 3.063 8.692 12.935 à
S-12505 3.125 9.050 13.469 à
S-4666 3.250 9.789 14.580 P à
S-6874 3.500 11.353 16.895 à à
S-13826 3.625 12.178 18.123 P
S-11050 3.750 13.033 19.395 à à
S-8748 3.875 13.916 20.709 P
S-6852 4.000 14.828 22.066 à
S-6860 4.250 16.739 24.910 à
S-4873 4.500 18.780 27.930 P
S-21378 4.750 20.910 31.118 P

Hexagonal Bar
Die Number Dim. (W) WT. (LBS/FT) WT. (KGS/MT) Toronto Ohio
S-12511 0.625 0.399 0.593 P
S-13002 0.750 0.575 0.855 P P
S-13003 0.875 0.782 1.164 P
S-2364 1.125 1.293 1.924 P
S-6529 1.750 3.129 4.657 P
S-24770 3.000 9.197 13.687 P

Tee Bars
Architectural
Die Number Dim. (B) Dim. (H) Dim. (P) Dim. (T) WT. (LBS/FT) WT. (KGS/MT) Toronto Ohio
S-9158 1.000 2.000 0.063 0.063 0.217 0.323 P
S-8568 1.000 2.000 0.118 0.118 0.401 0.597 P
S-4465 1.250 1.250 0.100 0.100 0.283 0.421 P
S-3317 1.250 1.250 0.187 0.187 0.511 0.760 P
S-6873 2.000 2.000 0.125 0.125 0.571 0.850 P P
S-4574 2.000 2.000 0.187 0.187 0.841 1.252 P P
S-22527 2.000 2.000 0.250 0.250 1.106 1.646 P
S-29327 2.500 2.000 0.190 0.190 0.966 1.438 P
S-29326 3.000 3.000 0.188 0.188 1.289 1.918 P

Tee Bars
Structural
Die Number Dim. (B) Dim. (H) Dim. (P) Dim. (T) Dim. (R) WT. (LBS/FT) WT. (KGS/MT) Toronto Ohio
S-6871 0.625 1.312 0.080 0.080 0.031 0.176 0.262 P
S-3303 1.250 1.250 0.187 0.187 0.187 0.529 0.787 P
S-2291 1.500 1.500 0.187 0.187 0.187 0.638 0.949 P
S-2823 2.000 1.500 0.187 0.187 0.187 0.761 1.132 P
S-2292 2.000 2.000 0.250 0.250 0.250 1.138 1.693 P
S-7903 2.000 2.100 0.120 0.120 0.120 0.570 0.848 P
S-4649 3.000 3.000 0.375 0.375 0.375 2.561 3.811 P P
S-2846 4.000 1.625 0.125 0.125 0.125 0.815 1.213 P
S-18614 4.000 4.000 0.375 0.375 0.375 3.445 5.126 P
S-5335 4.000 5.000 0.500 0.500 0.500 5.141 7.651 P
S-3272 5.000 3.000 0.375 0.375 0.312 3.446 5.128 P
S-7737 5.000 3.000 0.375 0.375 0.375 3.444 5.126 P

Angles, Equal Legs

Architectural
Die Number Dim (W) Dim (T) WT. (LBS/FT) WT. (KGS/MT) Toronto Ohio
S-3838 0.500 0.125 0.129 0.192 P
S-3488 0.750 0.062 0.105 0.156 P
S-25461 0.750 0.075 0.260 0.188 P
S-2240 0.750 0.125 0.203 0.302 P P
S-6095 0.906 0.177 0.342 0.508 P
S-3804 1.000 0.062 0.142 0.211 P P
S-4464 1.000 0.100 0.224 0.333 P
S-2238 1.000 0.125 0.277 0.412 P P
S-3316 1.000 0.187 0.400 0.595 P
S-4473 1.240 0.240 0.635 0.945 P
S-22341 1.250 0.094 0.267 0.397 P
S-2416 1.250 0.125 0.350 0.521 P P
S-15797 1.250 0.187 0.510 0.759 P P
S-10940 1.500 0.062 0.215 0.319 P P
S-2241 1.500 0.125 0.424 0.631 P P
S-2103 1.500 0.187 0.621 0.924 P P
S-13142 1.500 0.250 0.811 1.207 P
S-15988 1.500 0.250 0.811 1.207 P
S-2360 1.750 0.125 0.498 0.741 P
S-2109 1.750 0.187 0.731 1.087 P P
S-3821 1.750 0.250 0.959 1.427 P
S-5129 2.000 0.125 0.571 0.850 P P
S-2199 2.000 0.187 0.841 1.251 P P
S-2456 2.000 0.250 1.106 1.646 P P
S-3051 2.500 0.125 0.719 1.070 P P
S-3615 2.500 0.187 1.062 1.580 P P
S-15150 2.500 0.250 1.401 2.085 P P
S-21456 3.000 0.125 0.866 1.289 P P
S-15151 3.000 0.250 1.696 2.524 P P
S-2418 3.000 0.375 2.489 3.704 P
S-2123 3.000 0.500 3.245 4.829 P P
S-27195 4.000 0.250 2.286 3.402 P

Angles, Equal Legs

Structural
Die Number Dim. (W) Dim. (T) Dim. (R) WT. (LBS/FT) WT. (KGS/MT) Toronto Ohio
S-2197 0.500 0.062 0.062 0.070 0.104 P
S-2200 0.625 0.125 0.062 0.166 0.247 P
S-2239 0.750 0.125 0.125 0.207 0.308 P P
S-2228 1.000 0.125 0.125 0.281 0.418 P P
S-3302 1.000 0.187 0.187 0.409 0.609 P P
S-3808 1.000 0.250 0.250 0.532 0.792 P P
S-4773 1.250 0.125 0.125 0.354 0.527 P
S-2321 1.250 0.187 0.187 0.519 0.772 P P
S-2586 1.250 0.250 0.250 0.680 1.012 P
S-2154 1.500 0.125 0.125 0.428 0.637 P P
S-2108 1.500 0.187 0.187 0.630 0.937 P P
S-2310 1.500 0.250 0.250 0.827 1.231 P P
S-2318 1.750 0.250 0.250 0.975 1.451 P
S-3819 2.000 0.125 0.125 0.576 0.857 P P
S-2159 2.000 0.187 0.187 0.851 1.266 P P
S-2158 2.000 0.250 0.250 1.122 1.670 P P
S-2237 2.000 0.375 0.375 1.640 2.440 P P
S-2151 2.500 0.187 0.187 1.071 1.594 P
S-2414 2.500 0.250 0.250 1.417 2.108 P
S-5128 2.500 0.375 0.375 2.083 3.009 P
S-2236 3.000 0.187 0.187 1.292 1.922 P P
S-2227 3.000 0.250 0.250 1.712 2.547 P P
S-4667 3.000 0.375 0.375 2.525 3.756 P P
S-4774 3.000 0.500 0.500 3.309 4.924 P
S-24189 3.500 0.250 0.250 2.007 2.987 P
S-27750 3.500 0.375 0.375 2.967 4.415 P
S-22440 4.000 0.250 0.250 2.302 3.426 P
S-4668 4.000 0.312 0.312 2.856 4.250 P
S-4669 4.000 0.375 0.375 3.410 5.075 P P
S-28192 4.000 0.500 0.500 4.488 6.679 P
S-22741 6.000 0.375 0.375 5.179 7.708 P P

Angles, Equal Legs

Structural
Die Number Dim. (W) Dim. (T) Dim. (R) WT. (LBS/FT) WT. (KGS/MT) Toronto Ohio
S-22758 6.000 0.500 0.500 6.848 10.191 P P

Angles, Equal Legs

American Standard
Die Number Dim. (W) Dim. (T) Dim. (R) Dim. (R1) WT. (LBS/FT) WT. (KGS/MT) Toronto Ohio
S-22328 0.750 0.125 0.125 0.094 0.202 0.301 P
S-10520 1.000 0.125 0.125 0.094 0.276 0.411 P
S-24693 1.000 0.188 0.125 0.094 0.401 0.597 P
S-10521 1.000 0.250 0.125 0.094 0.516 0.767 P
S-12 1.250 0.125 0.188 0.125 0.351 0.523 P
S-24691 1.250 0.188 0.094 0.125 0.507 0.755 P
S-13 1.250 0.250 0.188 0.125 0.665 0.989 P
S-13546 1.500 0.125 0.188 0.125 0.425 0.633 P
S-10522 1.500 0.188 0.188 0.125 0.625 0.930 P
S-10523 1.500 0.250 0.188 0.125 0.812 1.209 P
S-14 1.750 0.250 0.188 0.125 0.960 1.428 P
S-10524 2.000 0.125 0.250 0.125 0.580 0.863 P
S-10525 2.000 0.188 0.250 0.125 0.853 1.270 P
S-10526 2.000 0.250 0.250 0.125 1.114 1.658 P
S-15 2.000 0.375 0.250 0.125 1.612 2.399 P
S-10527 2.500 0.188 0.250 0.125 1.075 1.600 P
S-10528 2.500 0.250 0.250 0.125 1.409 2.097 P
S-10529 2.500 0.375 0.250 0.125 2.054 3.057 P
S-10530 3.000 0.188 0.312 0.250 1.288 1.917 P
S-26326 3.000 0.250 0.250 0.250 1.680 2.501 P
S-10531 3.000 0.250 0.312 0.250 1.689 2.514 P
S-10532 3.000 0.375 0.312 0.250 2.482 3.693 P
S-10533 3.000 0.500 0.312 0.250 3.238 4.818 P
S-18 3.500 0.250 0.375 0.250 1.995 2.969 P
S-10534 4.000 0.250 0.375 0.250 2.290 3.408 P
S-10535 4.000 0.375 0.375 0.250 3.378 5.027 P
S-18268 4.000 0.500 0.375 0.250 4.429 6.591 P
S-21883 5.000 0.250 0.375 0.250 2.881 4.287 P
S-10536 5.000 0.375 0.500 0.375 4.251 6.327 P
S-24 5.000 0.500 0.500 0.375 5.597 8.329 P
S-18492 6.000 0.375 0.500 0.375 5.136 7.644 P
S-22733 6.000 0.625 0.500 0.380 8.379 12.469 P

Angles, Unequal Legs

Architectural
Die Number Dim. (B) Dim. (H) Dim. (T) WT. (LBS/FT) WT. (KGS/MT) Toronto Ohio
S-5502 0.625 0.500 0.062 0.078 0.116 P
S-12368 0.687 0.202 0.062 0.060 0.090 P
S-5784 0.750 0.375 0.120 0.143 0.212 P
S-2177 0.750 0.500 0.125 0.166 0.247 P
S-4261 0.950 0.810 0.125 0.241 0.359 P
S-24692 1.000 0.500 0.125 0.203 0.302 P
S-5597 1.000 0.625 0.065 0.119 0.177 P
S-2362 1.000 0.750 0.050 0.100 0.149 P
S-21967 1.000 0.750 0.062 0.123 0.183 P
S-6504 1.000 0.750 0.125 0.240 0.356 P P
S-3355 1.250 1.000 0.125 0.313 0.466 P P
S-4289 1.500 0.500 0.060 0.137 0.204 P
S-10065 1.500 0.625 0.125 0.295 0.439 P
S-2438 1.500 0.750 0.095 0.242 0.360 P
S-2243 1.500 0.750 0.125 0.314 0.467 P P
S-2751 1.500 1.000 0.055 0.158 0.235 P P
S-8136 1.500 1.000 0.063 0.181 0.269 P
S-2284 1.500 1.000 0.125 0.350 0.521 P P
S-25567 1.500 1.000 0.188 0.513 0.763 P
S-6641 1.625 0.750 0.188 0.485 0.722 P
S-2639 1.750 1.500 0.062 0.234 0.348 P
S-2206 1.875 1.125 0.125 0.424 0.631 P
S-5365 2.000 0.750 0.187 0.565 0.841 P
S-2954 2.000 1.000 0.055 0.191 0.284 P
S-9157 2.000 1.000 0.063 0.217 0.323 P P
S-17463 2.000 1.000 0.090 0.309 0.460 P P
S-8569 2.000 1.000 0.118 0.401 0.597 P
S-2397 2.000 1.000 0.125 0.424 0.631 P P
S-24876 2.000 1.000 0.188 0.624 0.928 P P
S-3854 2.000 1.250 0.055 0.208 0.310 P
S-2205 2.000 1.250 0.125 0.461 0.686 P
S-2286 2.000 1.500 0.125 0.498 0.741 P P
S-2242 2.000 1.500 0.187 0.732 1.089 P P

Architectural
S-11637 2.250 2.000 0.125 0.608 0.905 P
S-16648 2.500 1.000 0.125 0.498 0.741 P P
S-25178 2.500 1.250 0.125 0.534 0.795 P
S-2955 2.500 1.500 0.055 0.256 0.381 P
S-2423 2.500 1.500 0.125 0.571 0.850 P P
S-15021 2.500 1.500 0.188 0.845 1.258 P
S-16652 2.500 1.750 0.188 0.901 1.341 P
S-22265 3.000 0.750 0.125 0.534 0.795 P
S-8274 3.000 1.000 0.063 0.293 0.435 P
S-13664 3.000 1.000 0.125 0.571 0.850 P P
S-26689 3.000 1.500 0.250 1.253 1.865 P
S-13808 3.000 2.000 0.125 0.719 1.070 P P
S-2244 3.000 2.000 0.187 1.063 1.582 P
S-17185 3.000 2.000 0.250 1.401 2.085 P
S-26845 3.000 2.000 0.375 2.046 3.045 P
S-20810 3.125 1.875 0.188 1.067 1.588 P
S-9560 3.500 2.500 0.188 1.289 1.918 P
S-5880 4.000 1.000 0.125 0.719 1.069 P
S-30383 5.000 2.000 0.375 2.931 4.362 P
S-5881 6.000 1.000 0.125 1.014 1.508 P
S-30382 6.000 2.000 0.375 3.374 5.021 P
S-28082 6.000 4.000 0.375 4.259 6.338 P
S-26690 6.250 5.000 0.312 4.027 5.992 P
S-24215 8.000 4.000 0.250 3.466 5.158 P


Structural
Die Number Dim. (B) Dim. (H) Dim. (T) Dim. (R) WT. (LBS/FT) WT. (KGS/MT) Toronto Ohio
S-2178 1.250 1.000 0.125 0.125 0.317 0.472 P
S-3805 1.500 0.750 0.125 0.125 0.317 0.472 P
S-9935 1.500 1.000 0.125 0.125 0.354 0.527 P
S-2160 1.500 1.000 0.187 0.187 0.519 0.772 P
S-9567 1.750 0.750 0.090 0.094 0.258 0.385 P
S-7913 1.750 1.000 0.094 0.094 0.295 0.439 P
S-8592 1.750 1.125 0.070 0.094 0.258 0.385 P
S-2320 2.000 1.250 0.187 0.187 0.684 1.018 P
S-2153 2.000 1.500 0.187 0.187 0.740 1.101 P P
S-4854 2.000 1.500 0.250 0.250 0.975 1.450 P P
S-2152 2.500 1.500 0.187 0.187 0.851 1.266 P
S-2275 2.500 1.500 0.250 0.250 1.122 1.670 P
S-9934 2.500 2.000 0.125 0.125 0.649 0.966 P
S-20805 2.500 2.000 0.187 0.187 0.960 1.429 P
S-5361 2.500 2.000 0.250 0.250 1.270 1.889 P P
S-4860 2.500 2.000 0.375 0.375 1.861 2.769 P
S-17065 3.000 1.250 0.250 0.312 1.204 1.792 P
S-2188 3.000 2.000 0.187 0.187 1.071 1.594 P
S-3820 3.000 2.000 0.250 0.250 1.417 2.109 P P
S-6858 3.000 2.000 0.375 0.375 2.082 3.098 P P
S-4855 3.500 2.500 0.250 0.250 1.712 2.548 P
S-11644 4.000 1.125 0.090 0.125 0.538 0.801 P
S-17580 4.000 2.000 0.250 0.250 1.680 2.500 P P
S-2306 4.000 3.000 0.250 0.250 2.007 2.986 P P
S-4670 4.000 3.000 0.375 0.375 2.968 4.417 P P
S-28426 4.000 3.000 0.500 0.500 3.898 5.801 P
S-23642 5.000 3.000 0.312 0.312 2.855 4.248 P
S-23242 5.000 3.000 0.375 0.375 3.409 5.074 P
S-4861 5.000 3.500 0.375 0.375 3.631 5.403 P


Structural
Die Number Dim. (B) Dim. (H) Dim. (T) Dim. (R) WT. (LBS/FT) WT. (KGS/MT) Toronto Ohio
S-6371 6.000 1.750 0.250 0.250 2.228 3.316 P
S-17669 6.000 3.000 0.375 0.375 3.852 5.732 P
S-4671 6.000 4.000 0.375 0.375 4.295 6.392 P P
S-4672 6.000 4.000 0.500 0.500 5.669 8.436 P


American Standard
Die Number Dim. (B) Dim. (H) Dim. (T) Dim. (R) Dim. (R1) WT. (LBS/FT) WT. (KGS/MT) Toronto Ohio
S-15372 1.500 1.000 0.188 0.188 0.188 0.504 0.750 P
S-30336 1.500 1.250 0.125 0.125 0.100 0.386 0.574 P
S-10537 2.000 1.500 0.125 0.188 0.125 0.499 0.743 P
S-10538 2.000 1.500 0.188 0.188 0.125 0.736 1.095 P
S-28 2.000 1.500 0.250 0.188 0.125 0.960 1.428 P
S-26692 2.500 1.500 0.188 0.188 0.188 0.837 1.245 P
S-16470 2.500 1.500 0.188 0.250 0.125 0.853 1.270 P
S-25197 2.500 1.500 0.250 0.250 0.125 1.114 1.658 P
S-30 2.500 2.000 0.188 0.250 0.125 0.964 1.435 P
S-10539 2.500 2.000 0.250 0.250 0.125 1.261 1.877 P
S-11669 3.000 1.250 0.250 0.312 0.188 1.187 1.766 P
S-10540 3.000 2.000 0.188 0.312 0.188 1.074 1.599 P
S-10541 3.000 2.000 0.250 0.312 0.188 1.408 2.095 P
S-10542 3.000 2.000 0.375 0.312 0.188 2.053 3.055 P
S-31 3.000 2.500 0.250 0.313 0.250 1.542 2.295 P
S-26693 3.500 1.500 0.250 0.250 0.125 1.409 2.097 P
S-10543 3.500 2.500 0.250 0.312 0.250 1.689 2.514 P
S-23127 4.000 2.500 0.375 0.375 0.250 2.714 4.039 P
S-10544 4.000 3.000 0.250 0.375 0.250 1.995 2.969 P
S-26327 4.000 3.000 0.312 0.312 0.250 2.455 3.654 P
S-10545 4.000 3.000 0.375 0.375 0.250 2.935 4.368 P
S-24929 5.000 3.000 0.250 0.375 0.250 2.290 3.408 P
S-12660 5.000 3.000 0.375 0.438 0.313 3.373 5.019 P
S-24115 6.000 3.500 0.375 0.375 0.375 4.002 5.956 P
S-27277 6.000 4.000 0.375 0.500 0.375 4.251 6.327 P
S-40 6.000 4.000 0.500 0.500 0.375 5.597 8.329 P
S-25241 6.000 5.000 0.250 0.375 0.250 3.175 4.725 P

I-Beam and H-Beam

Aluminum Association
Die Number Dim. (W) Dim. (H) Dim. (P) Dim. (T) Dim. (R) WT. (LBS/FT) WT. (KGS/MT) Toronto Ohio
S-6872 2.000 3.000 0.250 0.188 0.375 1.876 2.792 P
S-20807 2.000 4.375 0.250 0.250 0.250 2.386 3.551 P
S-26468 2.250 4.000 0.215 0.135 0.105 1.720 2.559 P
S-23017 2.500 3.000 0.250 0.187 0.375 2.169 3.227 P
S-23023 3.000 4.000 0.230 0.150 0.250 2.318 3.450 P
S-27040 3.000 4.000 0.250 0.188 0.375 2.689 4.001 P
S-30270 3.000 4.000 0.312 0.188 0.375 3.100 4.613 P
S-2296 3.000 5.000 0.218 0.250 0.437 3.083 4.588 P
S-3859 3.500 6.000 0.375 0.250 0.438 4.840 7.202 P
S-26738 4.000 4.000 0.250 0.375 0.437 3.846 5.723 P
S-5258 4.000 4.000 0.312 0.250 0.437 4.135 6.153 P P
S-57 4.000 6.000 0.279 0.230 0.250 4.174 6.211 P
S-20791 4.000 6.000 0.375 0.281 0.437 5.474 8.146 P
S-24405 4.500 7.000 0.380 0.230 0.300 5.820 8.661 P
S-20801 5.000 5.000 0.313 0.313 0.438 5.494 8.177 P P
S-4403 5.000 5.000 0.375 0.312 0.562 6.309 9.389 P P
S-21927 5.000 8.000 0.410 0.250 0.300 7.047 10.487 P
S-27029 5.000 8.000 0.500 0.311 0.563 8.790 13.081 P
S-26325 5.250 8.000 0.308 0.230 0.320 5.923 8.815 P
S-58 6.000 6.000 0.269 0.240 0.250 5.419 8.064 P
S-5411 6.000 6.000 0.375 0.312 0.625 7.638 11.366 P
S-24769 6.000 6.000 0.500 0.375 0.375 9.435 14.040 P
S-4851 7.250 5.500 0.312 0.250 0.312 6.876 10.232 P
S-17391 8.000 8.000 0.433 0.288 0.400 10.761 16.014 P
S-20745 8.000 8.000 0.500 0.375 0.750 13.107 19.505 P

I-Beam and H-Beam

American Standard
Die Number Dim. (H) Dim. (W) Dim. (T) Dim. (P) Dim. (R) Dim. (R1) WT. WT. Toronto Ohio
(LBS/FT) (KGS/MT)
S-13562 2.510 3.000 0.349 0.170 0.270 0.090 2.606 3.878 P
S-55 2.660 4.000 0.190 0.190 0.290 0.110 2.654 3.949 P
S-56 3.000 5.000 0.210 0.210 0.310 0.210 3.442 5.122 P
S-16375 3.449 6.000 0.343 0.230 0.330 0.140 5.106 7.598 P
S-63 4.000 4.000 0.313 0.290 0.313 0.145 4.774 7.104 P
S-64 5.938 6.000 0.250 0.360 0.313 0.180 7.882 11.730 P
S-26340 6.125 6.000 0.438 0.347 0.313 0.180 9.184 13.667 P

Channels
Architectual
S-3204 0.500 0.500 0.062 0.062 0.101 0.150 P
S-3206 0.500 0.625 0.062 0.062 0.119 0.177 P
S-3400 0.500 0.750 0.125 0.125 0.258 0.384 P P
S-2141 0.625 0.625 0.062 0.062 0.129 0.191 P
S-2207 0.625 0.750 0.062 0.062 0.146 0.217 P
S-5792 0.625 1.250 0.062 0.062 0.219 0.327 P
S-26694 0.730 1.110 0.110 0.110 0.354 0.527 P
S-2255 0.750 0.500 0.125 0.125 0.222 0.330 P
S-7242 0.750 0.750 0.062 0.062 0.156 0.232 P
S-7577 0.750 0.750 0.125 0.125 0.295 0.439 P P
S-26695 0.750 1.375 0.125 0.125 0.479 0.713 P
S-2121 0.875 0.875 0.050 0.050 0.149 0.222 P
S-2138 1.000 0.500 0.125 0.125 0.258 0.384 P P
S-22112 1.000 0.750 0.065 0.065 0.182 0.270 P
S-9081 1.000 0.750 0.125 0.125 0.332 0.493 P
S-7243 1.000 1.000 0.125 0.125 0.406 0.604 P P
S-16346 1.000 2.000 0.125 0.125 0.700 1.042 P
S-19866 1.250 0.500 0.125 0.125 0.295 0.439 P
S-3326 1.250 0.625 0.125 0.125 0.332 0.494 P
S-26696 1.250 0.687 0.250 0.250 0.626 0.932 P
S-26697 1.250 0.781 0.250 0.375 0.682 1.015 P
S-4647 1.260 1.145 0.125 0.125 0.486 0.723 P
S-20926 1.360 1.000 0.048 0.048 0.191 0.284 P
S-7809 1.450 1.000 0.125 0.125 0.472 0.702 P
S-6855 1.500 0.500 0.125 0.125 0.332 0.493 P P
S-2703 1.500 0.625 0.093 0.093 0.281 0.418 P
S-8943 1.500 0.750 0.063 0.063 0.212 0.316 P
S-25206 1.500 0.750 0.125 0.125 0.405 0.603 P
S-7791 1.500 1.000 0.125 0.125 0.479 0.713 P P
S-7235 1.500 1.500 0.125 0.125 0.627 0.932 P
S-21823 1.500 1.500 0.250 0.250 1.180 1.756 P
S-22230 1.625 0.750 0.125 0.125 0.424 0.631 P

Channels
Architectual
S-3521 1.688 1.330 0.080 0.080 0.395 0.588 P
S-15193 1.750 1.625 0.125 0.125 0.700 1.042 P
S-2122 1.875 0.875 0.050 0.050 0.208 0.309 P
S-9530 2.000 1.000 0.062 0.062 0.283 0.421 P
S-3356 2.000 1.000 0.125 0.125 0.553 0.823 P P
S-28963 2.000 1.000 0.188 0.188 0.804 1.196 P
S-70 2.000 2.000 0.250 0.250 1.622 2.414 P
S-21966 2.500 1.000 0.125 0.125 0.627 0.932 P
S-2440 2.500 1.312 0.188 0.188 1.054 1.568 P
S-4254 2.500 1.500 0.125 0.125 0.774 1.152 P P
S-16431 2.500 1.500 0.188 0.188 1.136 1.691 P
S-26921 2.500 2.000 0.250 0.375 2.065 3.073 P
S-27948 2.938 4.000 0.125 0.250 1.973 2.936 P
S-27937 3.000 0.500 0.125 0.125 0.553 0.823 P
S-2752 3.000 1.000 0.125 0.125 0.701 1.043 P P
S-3512 3.000 1.500 0.125 0.125 0.848 1.262 P
S-9709 3.000 1.500 0.187 0.187 1.241 1.847 P P
S-4503 3.750 1.250 0.187 0.187 1.297 1.930 P
S-26698 4.000 0.969 0.125 0.125 0.839 1.248 P
S-3138 4.000 1.000 0.100 0.100 0.684 1.018 P P
S-26437 4.000 1.650 0.250 0.180 1.716 2.554 P
S-4619 4.200 0.500 0.062 0.062 0.372 0.554 P
S-3399 4.500 4.500 0.125 0.125 1.954 2.908 P
S-22687 5.000 2.000 0.188 0.188 1.913 2.847 P
S-20924 5.000 2.000 0.250 0.250 2.507 3.731 P
S-22434 5.250 1.000 0.125 0.125 1.032 1.536 P
S-10169 5.906 1.969 0.197 0.197 2.194 3.266 P
S-26440 6.000 2.000 0.230 0.200 2.392 3.560 P

Channels
Structural
S-2330 0.500 0.562 0.062 0.060 0.062 0.110 0.164 P
S-2798 1.250 1.250 0.125 0.125 0.125 0.524 0.780 P
S-2139 1.500 0.500 0.125 0.125 0.062 0.334 0.497 P
S-3446 1.725 1.475 0.125 0.125 0.125 0.661 0.984 P
S-9933 2.000 1.000 0.125 0.125 0.125 0.561 0.834 P
S-24927 2.000 1.250 0.250 0.188 0.130 1.078 1.605 P
S-6853 2.000 1.500 0.125 0.125 0.125 0.708 1.054 P
S-4675 2.000 2.000 0.125 0.125 0.125 0.855 1.272 P
S-25095 2.250 1.000 0.125 0.125 0.125 0.598 0.889 P
S-4645 2.250 1.000 0.188 0.188 0.188 0.877 1.305 P
S-8648 2.250 1.500 0.188 0.188 0.188 1.099 1.635 P
S-3920 3.000 1.500 0.125 0.125 0.125 0.856 1.274 P
S-51 3.000 1.500 0.200 0.130 0.250 1.138 1.694 P
S-2247 3.000 1.500 0.250 0.187 0.312 1.486 2.211 P
S-2246 3.000 1.500 0.312 0.250 0.312 1.855 2.760 P
S-23764 3.000 1.500 0.375 0.375 0.375 2.394 3.563 P
S-24928 3.000 1.750 0.260 0.170 0.250 1.603 2.385 P
S-22095 3.000 2.000 0.250 0.250 0.250 1.949 2.900 P P
S-2245 3.000 2.000 0.312 0.250 0.187 2.191 3.260 P
S-23757 4.000 1.500 0.250 0.250 0.250 1.949 2.900 P
S-4646 4.000 1.750 0.250 0.250 0.250 2.097 3.121 P
S-12537 4.000 1.812 0.250 0.188 0.312 1.894 2.818 P
S-25972 4.000 2.000 0.230 0.150 0.250 1.743 2.595 P
S-2107 4.000 2.000 0.250 0.187 0.375 2.024 3.012 P
S-22502 4.000 2.000 0.250 0.250 0.188 2.230 3.319 P
S-4862 4.000 2.000 0.250 0.250 0.250 2.244 3.339 P P
S-2328 4.000 2.000 0.312 0.250 0.375 2.539 3.778 P
S-16347 4.000 2.250 0.290 0.190 0.250 2.338 3.479 P
S-2312 4.000 2.500 0.312 0.250 0.187 2.854 4.247 P
S-4435 5.000 2.000 0.312 0.187 0.375 2.509 3.734 P
S-24768 5.000 2.000 0.343 0.281 0.375 3.120 4.644 P
S-52 5.000 2.250 0.260 0.150 0.300 2.219 3.302 P
S-4399 5.000 2.500 0.312 0.218 0.437 3.063 4.559 P
Channels
Structural
S-20594 5.000 2.500 0.375 0.250 0.437 3.563 5.302 P
S-53 5.000 2.750 0.320 0.190 0.300 3.100 4.613 P
S-22894 5.800 1.500 0.187 0.125 0.125 1.470 2.188 P
S-24926 6.000 1.250 0.200 0.200 0.190 1.930 2.871 P
S-4400 6.000 2.000 0.375 0.281 0.437 3.607 5.368 P
S-26879 6.000 2.500 0.290 0.170 0.300 2.834 4.232 P
S-4968 6.000 2.500 0.312 0.250 0.437 3.523 5.243 P P
S-6966 6.000 2.500 0.437 0.375 0.437 4.943 7.356 P
S-8605 6.000 2.750 0.375 0.250 0.437 4.079 6.071 P
S-199 6.000 3.250 0.350 0.210 0.300 4.034 6.017 P
S-6854 6.000 3.500 0.500 0.375 0.437 6.439 9.583 P
S-26333 7.000 2.750 0.290 0.170 0.300 3.215 4.785 P
S-2822 7.000 3.000 0.375 0.250 0.500 4.626 6.884 P
S-26739 8.000 2.290 0.250 0.313 0.437 4.218 6.276 P
S-18427 8.000 3.000 0.438 0.281 0.500 5.590 8.318 P
S-22053 10.000 3.000 0.437 0.281 0.500 6.246 9.295 P
S-18109 10.000 3.500 0.500 0.312 0.562 7.603 11.315 P
S-18110 12.000 4.000 0.562 0.375 0.625 10.315 15.351 P

Channels
American Standard
Die Number Dim. (B) Dim. (H) Dim. (P) Dim. (T) Dim. (R) Dim. (R1) WT. WT. Toronto Ohio
(LBS/FT) (KGS/MT)
S-10509 3.000 1.410 0.170 0.170 0.270 0.100 1.423 2.118 P
S-10510 3.000 1.498 0.170 0.258 0.270 0.100 1.735 2.581 P
S-10511 3.000 1.596 0.170 0.356 0.270 0.100 2.082 3.098 P
S-10512 4.000 1.580 0.180 0.180 0.280 0.110 1.852 2.757 P
S-10513 4.000 1.647 0.180 0.247 0.280 0.110 2.169 3.227 P
S-10514 4.000 1.720 0.180 0.320 0.280 0.110 2.513 3.740 P P
S-10515 5.000 1.750 0.190 0.190 0.290 0.110 2.324 3.458 P
S-41 5.000 1.885 0.190 0.325 0.290 0.110 3.120 4.643 P
S-24114 6.000 1.250 0.186 0.188 0.250 0.125 2.203 3.278 P
S-43 6.000 1.920 0.200 0.200 0.300 0.120 2.836 4.220 P
S-10516 6.000 1.945 0.200 0.225 0.300 0.120 3.013 4.483 P
S-10517 6.000 2.034 0.200 0.314 0.300 0.120 3.643 5.421 P
S-45 6.000 2.157 0.200 0.437 0.300 0.120 4.514 6.717 P
S-10518 7.000 2.110 0.210 0.230 0.310 0.130 3.554 5.289 P
S-26337 7.000 2.194 0.210 0.314 0.310 0.130 4.248 6.321 P
S-47 8.000 2.290 0.220 0.250 0.320 0.130 4.267 6.350 P
S-10519 10.000 2.600 0.240 0.240 0.340 0.140 5.297 7.883 P
S-25630 12.000 2.960 0.280 0.300 0.380 0.170 7.215 10.737 P

Square Tubes
Square Corners
H-3855 0.500 0.050 0.106 0.158 P
H-22243 0.625 0.050 0.136 0.202 P
H-5140 0.750 0.050 0.165 0.246 P
H-17510 0.750 0.062 0.201 0.299 P P
H-6859 0.750 0.120 0.356 0.530 P P
H-26849 0.750 0.125 0.369 0.549 P
H-6869 0.995 0.125 0.513 0.764 P
H-18984 1.000 0.062 0.274 0.408 P
H-9376 1.000 0.090 0.387 0.576 P
H-2439 1.000 0.095 0.406 0.604 P P
H-4237 1.000 0.120 0.498 0.741 P P
H-3325 1.250 0.120 0.640 0.952 P
H-8195 1.250 0.125 0.663 0.987 P P
H-6868 1.250 0.125 0.664 0.987 P
H-2322 1.500 0.050 0.342 0.509 P
H-23647 1.500 0.062 0.421 0.626 P
H-18396 1.500 0.070 0.472 0.703 P
H-9367 1.500 0.075 0.504 0.750 P
H-23648 1.500 0.093 0.617 0.919 P
H-7215 1.500 0.095 0.630 0.938 P
H-2179 1.500 0.120 0.781 1.162 P P
H-22212 1.500 0.188 1.164 1.732 P P
H-25464 1.500 0.250 1.475 2.195 P
H-20639 1.625 0.100 0.719 1.070 P
H-17559 1.750 0.062 0.494 0.735 P
H-25661 1.750 0.093 0.727 1.082 P
H-7216 1.750 0.094 0.735 1.094 P
H-2585 1.750 0.120 0.923 1.373 P P
H-3154 1.775 0.085 0.678 1.008 P
H-20641 2.000 0.060 0.549 0.817 P
H-23646 2.000 0.093 0.837 1.246 P
H-7217 2.000 0.095 0.854 1.271 P
H-2270 2.000 0.120 1.064 1.583 P P
Square Tubes
Square Corners
H-22327 2.000 0.125 1.106 1.646 P
H-18426 2.000 0.188 1.608 2.393 P P
H-17072 2.000 0.250 2.065 3.073 P P
H-8730 2.180 0.062 0.620 0.922 P
H-20640 2.500 0.075 0.858 1.227 P
H-7218 2.500 0.125 1.401 2.084 P P
H-27087 2.500 0.188 2.051 3.053 P
H-24875 2.500 0.250 2.655 3.951 P P
H-9847 2.625 0.125 1.474 2.193 P
H-5200 3.000 0.125 1.696 2.523 P P
H-24939 3.000 0.188 2.495 3.713 P P
H-6856 3.000 0.250 3.245 4.829 P P
H-3203 4.000 0.090 1.661 2.472 P
H-20569 4.000 0.125 2.286 3.401 P P
H-23960 4.000 0.187 3.365 5.008 P P
H-15202 4.000 0.250 4.425 6.585 P P
H-23024 4.000 0.375 6.416 9.548 P P
H-22210 4.000 0.500 8.260 12.292 P
H-13109 4.364 0.109 2.187 3.254 P
H-7574 4.500 0.100 2.077 3.091 P
H-7072 4.500 0.125 2.581 3.840 P
H-15003 5.000 0.250 5.605 8.341 P
H-20593 5.000 0.375 8.186 12.182 P P
H-12287 5.830 0.109 2.943 4.380 P
H-19501 6.000 0.125 3.466 5.158 P
H-21586 6.000 0.188 5.157 7.675 P

Square Tubes
Round Corners
Die Number Dim. (W) Dim. (T) Dim. (R) Dim. (Q) WT. (LBS/FT) WT. (KGS/MT) Toronto Ohio
H-20638 0.750 0.050 0.045 0.010 0.163 0.243 P
H-2433 0.750 0.064 0.093 0.029 0.199 0.296 P
H-4466 0.750 0.100 0.093 0.000 0.299 0.445 P P
H-20815 0.938 0.125 0.093 0.015 0.471 0.701 P
H-5117 1.000 0.050 0.125 0.075 0.214 0.318 P
H-6444 1.000 0.063 0.157 0.094 0.263 0.391 P P
H-6846 1.000 0.064 0.156 0.092 0.267 0.397 P
H-13656 1.000 0.065 0.125 0.060 0.275 0.409 P
H-2137 1.000 0.075 0.156 0.081 0.309 0.460 P P
H-20816 1.000 0.080 0.250 0.170 0.313 0.465 P
H-22067 1.000 0.090 0.125 0.035 0.372 0.554 P
H-9566 1.000 0.090 0.156 0.066 0.366 0.544 P P
H-20796 1.000 0.100 0.093 0.015 0.416 0.619 P
H-6026 1.000 0.100 0.156 0.056 0.404 0.601 P
H-24083 1.000 0.120 0.120 0.120 0.498 0.742 P P
H-2669 1.000 0.120 0.156 0.036 0.476 0.708 P P
H-22068 1.000 0.125 0.062 0.010 0.512 0.763 P
H-13658 1.000 0.125 0.125 0.010 0.501 0.745 P
H-11867 1.250 0.090 0.125 0.035 0.478 0.712 P
H-20797 1.250 0.100 0.093 0.015 0.534 0.795 P
H-10063 1.250 0.100 0.156 0.056 0.522 0.776 P P
H-2442 1.250 0.120 0.156 0.036 0.617 0.918 P P
H-21580 1.250 0.120 0.250 0.130 0.594 0.884 P
H-10280 1.250 0.125 0.093 0.000 0.655 0.975 P
H-8381 1.250 0.125 0.187 0.063 0.631 0.939 P
H-25352 1.250 0.125 0.188 0.063 0.632 0.940 P
H-9777 1.440 0.050 0.100 0.050 0.321 0.478 P
H-6445 1.500 0.083 0.177 0.094 0.532 0.792 P
H-20071 1.500 0.090 0.090 0.090 0.599 0.891 P
H-9076 1.500 0.095 0.156 0.061 0.609 0.906 P
H-20798 1.500 0.100 0.093 0.015 0.652 0.971 P
H-3807 1.500 0.120 0.156 0.036 0.759 1.129 P P
H-22496 1.500 0.120 0.312 0.192 0.720 1.072 P
Square Tubes
Round Corners
H-27163 1.500 0.120 0.370 0.250 0.706 1.051 P
H-30390 1.500 0.125 0.250 0.125 0.764 1.137 P
H-16350 1.500 0.125 0.312 0.192 0.750 1.116 P P
H-19638 1.500 0.187 0.186 0.156 1.149 1.709 P P
H-10357 1.550 0.125 0.125 0.080 0.832 1.238 P
H-24930 1.688 0.125 0.188 0.188 0.922 1.372 P
H-8712 1.700 0.135 0.225 0.090 0.955 1.421 P
H-8126 1.700 0.188 0.188 0.037 1.292 1.923 P
H-10073 1.820 0.120 0.280 0.160 0.910 1.354 P P
H-20072 2.000 0.090 0.090 0.090 0.811 1.207 P P
H-13894 2.000 0.100 0.100 0.000 0.886 1.319 P
H-11634 2.000 0.102 0.383 0.281 0.845 1.258 P
H-3839 2.000 0.120 0.255 0.135 1.017 1.513 P
H-22497 2.000 0.120 0.375 0.255 0.988 1.471 P
H-24938 2.000 0.125 0.125 0.000 1.091 1.623 P P
H-22294 2.000 0.125 0.125 0.125 1.106 1.646 P P
H-13659 2.000 0.125 0.187 0.062 1.075 1.599 P
H-6713 2.000 0.125 0.375 0.250 1.027 1.528 P P
H-22129 2.000 0.187 0.250 0.250 1.600 2.381 P P
H-24940 2.000 0.188 0.188 0.000 1.572 2.340 P P
H-18310 2.000 0.188 0.281 0.093 1.537 2.287 P P
H-29498 2.000 0.188 0.400 0.212 1.491 2.219 P
H-24937 2.000 0.250 0.250 0.000 2.002 2.979 P
H-27873 2.000 0.250 0.250 0.010 2.002 2.979 P
H-11478 2.000 0.250 0.375 0.125 1.938 2.885 P P
H-14696 2.375 0.160 0.375 0.215 1.577 2.347 P
H-13791 2.500 0.100 0.100 0.000 1.123 1.671 P
H-10074 2.500 0.120 0.280 0.160 1.294 1.926 P P
H-28771 2.500 0.125 0.500 0.375 1.290 1.920 P
H-25119 2.500 0.188 0.250 0.250 2.052 3.053 P
H-29053 2.500 0.250 0.250 0.125 2.608 3.880 P
H-13792 3.000 0.100 0.100 0.000 1.359 2.022 P
H-23746 3.000 0.125 0.187 0.063 1.665 2.478 P
Square Tubes
Round Corners
H-30389 3.000 0.125 0.250 0.125 1.649 2.454 P
H-6826 3.000 0.160 0.062 0.000 2.142 3.187 P
H-14181 3.000 0.160 0.280 0.120 2.080 3.095 P
H-13387 3.000 0.187 0.125 0.031 2.468 3.673 P
H-23747 3.000 0.188 0.187 0.063 2.464 3.667 P
H-13783 3.000 0.250 0.187 0.062 3.213 4.782 P P
H-22173 3.000 0.250 0.438 0.188 3.086 4.593 P P
H-22283 3.000 0.250 0.500 0.250 3.055 4.546 P
H-3134 3.375 0.500 0.125 0.125 6.770 10.074 P
H-10075 4.000 0.188 0.280 0.280 3.383 5.035 P P
H-11781 4.000 0.250 0.500 0.250 4.235 6.302 P P
H-13937 4.000 0.437 0.187 0.187 7.356 10.947 P
H-15425 4.500 0.188 0.375 0.188 3.719 5.534 P
H-26322 5.000 0.187 0.375 0.188 4.142 6.163 P
H-27671 5.000 0.250 0.500 0.250 5.415 8.059 P
H-20777 5.000 0.312 0.015 0.125 6.919 10.297 P

Rectangular Tubes
Square Corners
H-14871 0.750 0.500 0.050 0.134 0.200 P
H-18259 0.750 0.500 0.062 0.165 0.245 P
H-18514 1.000 0.500 0.125 0.369 0.549 P
H-9369 1.000 0.750 0.065 0.248 0.369 P
H-6821 1.015 0.520 0.065 0.216 0.321 P
H-15634 1.500 0.750 0.125 0.590 0.878 P P
H-26758 1.500 1.000 0.062 0.348 0.517 P
H-5514 1.500 1.000 0.090 0.493 0.734 P P
H-13784 1.500 1.000 0.125 0.664 0.988 P P
H-7298 1.750 1.000 0.125 0.738 1.098 P
H-3830 2.000 1.000 0.095 0.630 0.937 P P
H-4960 2.000 1.000 0.125 0.812 1.208 P P
H-23013 2.000 1.250 0.125 0.885 1.317 P
H-2592 2.000 1.500 0.120 0.923 1.373 P
H-16051 2.000 1.500 0.125 0.959 1.427 P
H-15010 2.500 1.000 0.100 0.779 1.159 P
H-2591 2.500 1.500 0.120 1.064 1.583 P P
H-25118 2.500 2.000 0.250 2.360 3.512 P
H-11036 3.000 0.750 0.080 0.678 1.008 P
H-22492 3.000 1.000 0.120 1.065 1.584 P
H-22330 3.000 1.000 0.125 1.106 1.646 P
H-13665 3.000 1.500 0.125 1.254 1.866 P P
H-16550 3.000 1.500 0.188 1.830 2.723 P P
H-21882 3.000 1.750 0.094 1.012 1.506 P
H-5261 3.000 2.000 0.120 1.348 2.005 P P
H-18513 3.000 2.000 0.188 2.051 3.053 P P
H-24170 3.000 2.000 0.250 2.655 3.951 P P
H-26321 3.250 1.250 0.200 1.935 2.880 P
H-5260 3.375 1.875 0.125 1.475 2.195 P
H-26334 4.000 1.500 0.250 2.950 4.390 P
H-3200 4.000 1.750 0.090 1.184 1.762 P P
H-21468 4.000 1.750 0.190 2.408 3.583 P
H-9368 4.000 2.000 0.120 1.631 2.427 P P
Rectangular Tubes
Square Corners
H-2249 4.000 2.000 0.187 2.483 3.695 P P
H-16405 4.000 2.000 0.250 3.245 4.829 P P
H-12575 4.000 2.000 0.375 4.606 6.855 P
H-25447 4.000 3.000 0.188 2.939 4.373 P
H-1070 4.000 3.000 0.250 3.835 5.707 P P
H-15644 4.500 1.750 0.090 1.289 1.918 P
H-10365 5.000 1.750 0.125 1.917 2.853 P
H-21569 5.000 2.000 0.125 1.991 2.963 P P
H-9550 5.000 2.500 0.188 3.161 4.704 P
H-6636 5.000 2.992 0.093 1.713 2.549 P
H-8751 5.000 4.000 0.125 2.581 3.841 P
H-7567 6.000 1.750 0.100 1.782 2.652 P
H-17430 6.000 2.000 0.120 2.198 3.270 P
H-1318 6.000 2.000 0.125 2.286 3.402 P
H-20019 6.000 2.000 0.188 3.382 5.034 P
H-15283 6.000 2.000 0.250 4.425 6.585 P P
H-13662 6.000 3.000 0.125 2.581 3.841 P
H-1317 6.000 3.000 0.187 3.807 5.665 P
H-15081 6.000 3.000 0.250 5.015 7.463 P
H-27086 6.000 4.000 0.188 4.270 6.354 P
H-13661 6.000 4.000 0.250 5.605 8.341 P P
H-8744 6.250 3.500 0.250 5.457 8.121 P
H-19567 8.000 3.000 0.250 6.195 9.219 P
H-25679 8.000 4.000 0.250 6.785 10.097 P
H-21471 8.000 6.000 0.250 7.965 11.853 P

Rectangular Tubes
Round Corners
Die Number Dim. (W) Dim. (H) Dim. (T) Dim. (R) Dim. (Q) WT. (LBS/FT) WT. (KGS/MT) Toronto Ohio
H-25349 1.000 0.500 0.125 0.125 0.063 0.357 0.531 P
H-9808 1.000 0.750 0.100 0.156 0.056 0.344 0.512 P
H-25351 1.000 0.750 0.125 0.188 0.063 0.411 0.611 P
H-15239 1.500 1.000 0.062 0.125 0.063 0.336 0.500 P
H-22160 1.500 1.000 0.120 0.250 0.125 0.593 0.882 P
H-25350 1.500 1.000 0.125 0.188 0.063 0.632 0.940 P
H-28769 1.500 1.000 0.188 0.250 0.250 0.940 1.399 P
H-15240 2.000 1.000 0.062 0.125 0.063 0.409 0.609 P P
H-27568 2.000 1.000 0.125 0.125 0.010 0.796 1.184 P
H-14173 2.000 1.000 0.125 0.125 0.125 0.811 1.207 P
H-8380 2.000 1.000 0.125 0.188 0.063 0.780 1.161 P P
H-17138 2.000 1.000 0.125 0.250 0.125 0.764 1.137 P
H-21585 2.000 1.250 0.090 0.060 0.010 0.649 0.965 P
H-28768 2.000 1.500 0.125 0.250 0.250 0.959 1.427 P
H-1183 2.500 1.000 0.125 0.250 0.125 0.911 1.356 P
H-393 2.500 1.250 0.125 0.156 0.036 1.009 1.502 P
H-11968 2.500 1.500 0.125 0.280 0.155 1.051 1.564 P P
H-11026 3.000 1.000 0.120 0.182 0.062 1.035 1.541 P P
H-20802 3.000 1.000 0.187 0.094 0.035 1.593 2.370 P
H-24941 3.000 1.500 0.125 0.188 0.063 1.222 1.818 P
H-17139 3.000 1.500 0.125 0.375 0.250 1.175 1.748 P
H-11967 3.000 2.000 0.120 0.280 0.160 1.295 1.926 P
H-15290 3.000 2.000 0.125 0.188 0.063 1.369 2.038 P P
H-27874 3.000 2.000 0.250 0.188 0.016 2.619 3.898 P
H-24842 3.000 2.000 0.250 0.250 0.125 2.608 3.880 P
H-24942 3.625 1.625 0.187 0.187 0.000 2.117 3.150 P
H-17949 4.000 1.000 0.125 0.125 0.010 1.386 2.062 P
H-27570 4.000 1.125 0.090 0.070 0.125 1.061 1.579 P
H-20701 4.000 1.250 0.125 0.250 0.120 1.426 2.123 P
H-28611 4.000 2.000 0.120 0.250 0.130 1.585 2.359 P
H-10076 4.000 2.000 0.120 0.280 0.280 1.632 2.429 P
H-20862 4.000 2.000 0.125 0.125 0.010 1.681 2.501 P
H-21813 4.000 2.000 0.125 0.188 0.063 1.664 2.477 P P
Rectangular Tubes
Round Corners
Die Number Dim. (W) Dim. (H) Dim. (T) Dim. (R) Dim. (Q) WT. (LBS/FT) WT. (KGS/MT) Toronto Ohio
H-23267 4.000 2.000 0.188 0.250 0.250 2.495 3.713 P
H-20861 4.000 2.000 0.250 0.187 0.187 3.245 4.826 P
H-27490 4.000 2.000 0.250 0.250 0.125 3.198 4.758 P
H-17937 5.000 1.000 0.125 0.062 0.010 1.692 2.519 P
H-14131 5.000 1.750 0.125 0.063 0.063 1.917 2.854 P
H-13988 5.000 2.000 0.125 0.250 0.125 1.944 2.893 P P
H-21486 5.000 2.000 0.250 0.250 0.125 3.788 5.636 P
H-25948 5.000 2.500 0.125 0.188 0.063 2.107 3.136 P
H-17298 5.000 3.000 0.250 0.250 0.250 4.425 6.585 P
H-3293 5.000 4.250 0.250 0.625 0.038 4.910 7.307 P
H-13989 6.000 2.000 0.125 0.250 0.125 2.239 3.332 P
H-23748 6.000 2.000 0.188 0.187 0.010 3.347 4.981 P P
H-21485 6.000 2.000 0.250 0.313 0.188 4.362 6.491 P
H-16426 6.000 4.000 0.250 0.375 0.125 5.478 8.153 P
H-20790 8.000 2.000 0.125 0.062 0.010 2.872 4.275 P P
H-1080 8.000 2.000 0.250 0.187 0.062 5.573 8.294 P
H-15316 8.000 2.500 0.250 0.187 0.062 5.868 8.732 P
H-27076 8.000 4.000 0.188 0.500 0.312 5.003 7.445 P
H-20817 8.000 4.000 0.250 0.031 0.016 6.727 10.010 P
H-20789 10.360 3.360 0.180 0.500 0.320 5.526 8.223 P

Round Tubes and Pipes
Die Number Dim. (D) Dim. (T) Remarks WT. (LBS/FT) WT. (KGS/MT) Toronto Ohio
H-4421 0.311 0.073 0.065 0.097 P
H-9664 0.435 0.050 0.072 0.107 P
H-10299 0.472 0.059 0.090 0.134 P
H-14695 0.500 0.049 0.082 0.122 P
H-2575 0.500 0.065 0.105 0.156 P
H-4951 0.540 0.088 1/4" SCH. 40 PIPE 0.148 0.220 P
H-4921 0.625 0.049 0.105 0.156 P
H-22251 0.625 0.065 0.135 0.201 P
H-6847 0.675 0.091 3/8" SCH. 40 PIPE 0.197 0.293 P P
H-5141 0.750 0.050 0.129 0.193 P
H-22432 0.750 0.058 0.149 0.221 P
H-2576 0.750 0.065 0.165 0.246 P P
H-28964 0.750 0.120 0.280 0.417 P
H-2156 0.840 0.109 1/2" SCH. 40 PIPE 0.295 0.439 P P
H-7765 0.840 0.147 1/2" SCH. 80 PIPE 0.378 0.562 P P
H-3910 0.865 0.125 0.343 0.510 P
H-3692 0.875 0.062 0.186 0.277 P P
H-12790 1.000 0.049 0.173 0.257 P
H-2367 1.000 0.065 0.225 0.335 P P
H-20848 1.000 0.100 0.334 0.497 P P
H-3846 1.000 0.120 0.392 0.583 P P
H-12319 1.000 0.215 0.626 0.931 P
H-15148 1.000 0.250 0.695 1.034 P P
H-2157 1.050 0.113 3/4" SCH. 40 PIPE 0.393 0.585 P P
H-15282 1.050 0.154 3/4" SCH. 80 PIPE 0.512 0.761 P
H-20925 1.125 0.125 0.463 0.690 P
H-26176 1.125 0.156 0.560 0.834 P
H-21449 1.125 0.247 0.805 1.198 P
H-1342 1.185 0.100 0.402 0.599 P
H-4917 1.250 0.050 0.222 0.331 P P
H-2101 1.250 0.058 0.256 0.381 P
H-4838 1.250 0.065 0.286 0.425 P P
H-13580 1.250 0.085 0.367 0.546 P
H-5157 1.250 0.095 0.407 0.606 P
H-2186 1.250 0.125 0.522 0.777 P P
H-22472 1.250 0.188 0.740 1.101 P
H-2637 1.250 0.250 0.926 1.378 P P
H-2304 1.250 0.327 1.119 1.665 P
H-12320 1.250 0.340 1.147 1.707 P
H-12123 1.250 0.409 1.275 1.898 P
H-2213 1.315 0.133 1" SCH. 40 PIPE 0.583 0.868 P P
H-3837 1.315 0.179 1" SCH. 80 PIPE 0.754 1.122 P P
H-5047 1.344 0.065 0.308 0.458 P
H-26516 1.375 0.125 0.579 0.862 P
H-23260 1.375 0.188 0.827 1.231 P
H-2794 1.425 0.125 0.603 0.897 P
H-2350 1.500 0.062 0.330 0.491 P P
H-13320 1.500 0.085 0.446 0.664 P
H-17285 1.500 0.085 0.446 0.664 P
H-2324 1.500 0.120 0.614 0.914 P P
H-22591 1.500 0.125 0.637 0.948 P
H-26469 1.500 0.157 0.779 1.160 P
H-27384 1.500 0.188 0.914 1.361 P
H-6861 1.500 0.250 1.159 1.724 P P
H-2424 1.500 0.453 1.758 2.616 P
H-5300 1.575 0.079 0.437 0.649 P
H-22043 1.625 0.437 1.926 2.860 P
H-15126 1.660 0.140 0.789 1.174 à
H-2214 1.660 0.140 1 1/4" SCH. 40 PIPE 0.789 1.174 P P
H-2503 1.660 0.191 1 1/4" SCH. 80 PIPE 1.040 1.548 P P
H-3089 1.660 0.268 1.381 2.055 P
H-6681 1.750 0.065 0.406 0.604 P P
H-20814 1.750 0.083 0.512 0.762 P
H-17286 1.750 0.095 0.583 0.867 P
H-23724 1.750 0.375 1.911 2.845 P
H-26177 1.795 0.300 1.663 2.474 P
H-4881 1.839 0.125 0.795 1.183 P P
H-13503 1.875 0.065 0.436 0.649 P
H-9687 1.900 0.109 1 1/2" SCH. 10 PIPE 0.723 1.076 P P
H-2212 1.900 0.145 1 1/2" SCH. 40 PIPE 0.943 1.403 P P
H-2467 1.900 0.200 1 1/2" SCH. 80 PIPE 1.260 1.875 P P
H-2274 1.900 0.385 2.162 3.217 P
H-5301 1.969 0.079 0.551 0.821 P
H-4891 2.000 0.065 0.466 0.693 P P
H-3847 2.000 0.120 0.837 1.245 P P
H-21377 2.000 0.125 0.869 1.293 P P
H-16474 2.000 0.188 1.263 1.879 P P
H-11344 2.000 0.250 1.622 2.414 P P
H-18189 2.000 0.375 2.259 3.362 P
H-21750 2.016 0.128 0.896 1.333 P
H-16294 2.125 0.065 0.496 0.739 P
H-20781 2.125 0.120 0.892 1.327 P
H-20637 2.125 0.375 2.433 3.620 P
H-22338 2.250 0.125 0.985 1.465 P
H-8417 2.250 0.188 1.437 2.139 P
H-16551 2.250 0.250 1.854 2.758 P
H-26339 2.250 0.375 2.607 3.879 P
H-5302 2.362 0.157 1.287 1.915 P
H-2211 2.375 0.154 2" SCH. 40 PIPE 1.269 1.888 P P
H-2466 2.375 0.218 2" SCH. 80 PIPE 1.743 2.594 P P
H-9354 2.375 0.218 2" SCH. 80 PIPE 1.743 2.594 P
H-11962 2.500 0.065 0.587 0.873 P
H-13657 2.500 0.065 0.587 0.873 à
H-20869 2.500 0.120 1.059 1.576 P
H-21397 2.500 0.125 1.101 1.638 P
H-17269 2.500 0.250 2.085 3.103 P
H-26330 2.500 0.375 2.954 4.396 P
H-21558 2.500 0.500 3.707 5.517 P
H-10078 2.530 0.135 1.199 1.784 P
H-19867 2.688 0.200 1.845 2.745 P
H-16081 2.750 0.250 2.317 3.449 P
H-3273 2.875 0.203 2 1/2" SCH. 40 PIPE 2.011 2.992 P P
H-2201 2.875 0.276 2 1/2" SCH. 80 PIPE 2.659 3.957 P P
H-5503 3.000 0.050 0.546 0.813 P
H-2577 3.000 0.065 0.707 1.052 P
H-3842 3.000 0.125 1.332 1.983 P
H-19266 3.000 0.187 1.950 2.902 P
H-19620 3.000 0.250 2.549 3.793 P P
H-29334 3.000 0.500 4.634 6.896 P
H-20281 3.000 0.516 4.751 7.071 P
H-20159 3.000 0.750 6.256 9.309 P
H-3136 3.062 0.281 2.897 4.311 P
H-5298 3.150 0.157 1.747 2.599 P
H-20283 3.250 0.250 2.780 4.138 P P
H-26323 3.250 0.375 3.997 5.948 P
H-26338 3.250 0.500 5.097 7.585 P
H-8495 3.500 0.083 3" SCH. 5 PIPE 1.051 1.565 P
H-16298 3.500 0.120 3" SCH. 10 PIPE 1.504 2.238 P P
H-2210 3.500 0.216 3" SCH. 40 PIPE 2.629 3.912 P P
H-6857 3.500 0.300 3" SCH. 80 PIPE 3.559 5.296 P P
H-21356 3.500 0.375 4.344 6.465 P
H-21470 3.500 0.750 7.646 11.378 P
H-5299 3.543 0.197 2.442 3.634 P
H-23172 3.620 0.665 7.285 10.841 P
H-3135 3.750 0.344 4.344 6.464 P
H-891 3.750 0.500 6.024 8.965 P
H-16034 4.000 0.065 0.948 1.411 P P
H-16517 4.000 0.083 1.205 1.794 P
H-3806 4.000 0.125 1.796 2.672 P P
H-23715 4.000 0.156 2.223 3.308 P
H-23068 4.000 0.188 2.657 3.954 P P
H-3274 4.000 0.226 3 1/2" SCH. 40 PIPE 3.162 4.705 P P
H-11496 4.000 0.318 3 1/2" SCH. 80 PIPE 4.341 6.459 P P
H-26324 4.000 0.375 5.039 7.499 P
H-21379 4.000 0.500 6.487 9.654 P
H-23171 4.120 0.915 10.871 16.178 P
H-23670 4.125 0.375 5.213 7.758 P
H-20780 4.500 0.083 4" SCH. 5 PIPE 1.359 2.022 P
H-18705 4.500 0.120 4" SCH. 10 PIPE 1.948 2.900 P
H-19509 4.500 0.120 4" SCH. 10 PIPE 1.948 2.900 P
H-6281 4.500 0.237 4" SCH. 40 PIPE 3.745 5.574 P P
H-6282 4.500 0.337 4" SCH. 80 PIPE 5.200 7.739 P P
H-26757 4.500 0.531 4" SCH. 160 PIPE 7.813 11.627 P
H-20779 5.000 0.083 1.513 2.251 P
H-23550 5.000 0.125 2.259 3.362 P
H-23595 5.000 0.156 2.801 4.169 P
H-23250 5.000 0.188 3.354 4.991 P
H-20332 5.000 0.245 4.319 6.427 P P
H-24621 5.000 0.437 7.392 11.001 P
H-17417 5.563 0.258 5" SCH. 40 PIPE 5.074 7.551 P P
H-20331 5.563 0.375 5" SCH. 80 PIPE 7.212 10.733 P P
H-23194 6.000 0.188 4.051 6.028 P P
H-17229 6.000 0.250 5.329 7.930 P P
H-5063 6.625 0.104 6" SCH. 5 PIPE 2.514 3.742 P
H-6399 6.625 0.134 6" SCH. 10 PIPE 3.225 4.799 P
H-9036 6.625 0.280 6" SCH. 40 PIPE 6.587 9.802 P P
H-21962 6.625 0.432 6" SCH 80 PIPE 9.918 14.759 P P
H-25529 8.000 0.250 7.182 10.689 P
H-14304 8.000 0.281 8.055 11.987 P
H-16450 8.000 0.453 12.674 18.861 P
H-17180 8.625 0.322 8" SCH 40 PIPE 9.911 14.749 P
H-20787 10.750 0.200 7.822 11.640 P

Zees
Die Number Dim. (H) Dim. (W) Dim. (T) Dim. (R) Dim. (R1) WT. (LBS/FT) WT. (KGS/MT) Toronto Ohio
S-25196 1.750 1.750 0.188 0.188 0.125 1.091 1.624 P
S-20927 2.000 1.000 0.062 0.010 0.015 0.283 0.422 P
S-23027 2.375 1.250 0.188 0.188 0.125 1.008 1.500 P
S-48 3.000 2.688 0.250 0.312 0.250 2.341 3.484 P
S-25250 4.000 1.000 0.125 0.010 0.015 0.848 1.262 P
S-49 4.000 3.063 0.250 0.312 0.250 2.857 4.252 P
S-12272 4.125 3.188 0.375 0.375 0.250 4.354 6.480 P

CHEMICAL COMPOSITION LIMITS
AA DESIGNATION SILICON IRON COPPER MANGANESE MAGNESIUM CHROMIUM ZINC TITANIUM OTHERS ALUMINUM
EACH TOTAL MINIMUM
6005A 0.60-0.9 0.35 0.1 0.1 0.40-0.60 0.1 0.1 0.1 0.05 0.15 BALANCE
6061 0.4-0.8 0.7 0.15-0.4 0.15 0.80-1.20 0.04-0.35 0.25 0.15 0.05 0.15 BALANCE
6063 0.20-0.6 0.35 0.1 0.1 0.45-0.90 0.1 0.1 0.1 0.05 0.15 BALANCE
6351 0.70-1.3 0.5 0.1 0.40-0.8 0.40-0.80 0.2 0.2 0.05 0.15 BALANCE
MECHANICAL PROPERTY LIMITS-EXTRUDED ROD, BAR AND PROFILES (SHAPES)
ALLOY &TEMPER SPECIFIED AREA TENSILE STRENGTH - KSI ELONGATION

DIAMETER OR (SQ. INCHES) (PERCENT
THICKNESS OR ULTIMATE YIELD MINIMUM
MIN DISTANCE MIN. MAX. MIN. MAX. IN 2 INCHES)
ACROSS FLATS
(INCHES)
6005A
6005A-T1 UP THRU 0.249 ALL 25.0 14.5 15.0
6005A-T5 UP THRU 0.249 ALL 38.0 31.0 7.0
0.250 - 0.999 ALL 38.0 31.0 9.0
6005A-T61 UP THRU 0.249 ALL 38.0 35.0 8.0
0.250 - 1.000 ALL 38.0 35.0 10.0
6061
6061-T1 UP THRU 0.625 ALL 26.0 14.0 16.0
6061-T4 ALL ALL 26.0 16.0 16.0
6061-T6 UP THRU 0.249 ALL 38.0 35.0 8.0
AND T6511 0.250 AND OVER ALL 38.0 35.0 10.0
6063
6063-T1 UP THRU 0.500 ALL 17.0 9.0 12.0
0.501 - 1.000 ALL 16.0 8.0 12.0
6063-T4 UP THRU 0.500 ALL 19.0 10.0 14.0
0.501 - 1.000 ALL 18.0 9.0 14.0
6063-T5 UP THRU 0.500 ALL 22.0 16.0 8.0
0.501 - 1.000 ALL 21.0 15.0 8.0
6063-T52 UP THRU 1.000 ALL 22.0 30.0 16.0 25.0 8.0
6063-T6 UP THRU 0.124 ALL 30.0 25.0 8.0
0.125 - 1.000 ALL 30.0 25.0 10.0
6351
6351-T1 UP THRU 0.499 UP THRU 20 26.0 13.0 15.0
6351-T4 UP THRU 0.749 ALL 32.0 19.0 16.0
6351-T5 UP THRU 0.249 ALL 38.0 35.0 8.0
0.250-1.000 ALL 38.0 35.0 10.0
6351-T6 UP THRU 0.124 ALL 42.0 37.0 8.0
0.125 - 0.749 ALL 42.0 37.0 10.0
Cextruded/standard tolerances
wire, rod, bar and profilesC
TABLE 11.2 CProfiles1

Cross-Sectional Dimension TolerancesC
EXCEPT FOR T3510, T4510, T6510, T73510, T76510 AND T8510 TEMPERS7
TOLERANCE23—in. plus and minus

METAL DIMENSIONS SPACE DIMENSIONS
ALLOWABLE DEVIATION FROM
ALLOWABLE DEVIATION FROM SPECIFIED
SPECIFIED DIMENSION WHERE
SPECIFIED DIMENSION WHERE MORE THAN 25 PERCENT OF
75 PERCENT OR MORE OF
DIMENSION THE DIMENSION IS SPACE68
THE DIMENSION IS METAL9bl
At At At At At At
in. Wall Thickness4
All Dimensioned Dimensioned Dimensioned Dimensioned Dimensioned Dimensioned
Completely5
Except Those Points Points Points Points Points Points
Enclosing Space
Covered 0.250–0.624 0.625–1.249 1.250–2.499 2.500–3.999 4.000–5.999 6.000–8.000
0.11 sq. in. and
by Column 3 inches from inches from inches from inches from inches from inches from
Over (Eccentricity)
Base of Leg Base of Leg Base of Leg Base of Leg Base of Leg Base of Leg
Col. 2 Col. 3 Col. 4 Col. 5 Col. 6 Col. 7 Col. 8 Col. 9
5xxx 5xxx 5xxx 5xxx 5xxx 5xxx 5xxx 5xxx
Col. 1 $4.0 Other $4.0 Other $4.0 Other $4.0 Other $4.0 Other $4.0 Other $4.0 Other $4.0 Other
nominal Alloys nominal Alloys nominal Alloys nominal Alloys nominal Alloys nominal Alloys nominal Alloys nominal Alloys
Mgbm Mgbm Mgbm Mgbm Mgbm Mgbm Mgbm Mgbm
CIRCUMSCRIBING CIRCLE SIZES LESS THAN 10 INCHES IN DIAMETER
±15% of specified dimension;
Up thru 0.124 .009 .006 .013 .010 .015 .012 .. .. .. .. .. .. .. ..

0.125–0.249 .011 .007 .016 .012 .018 .014 .020 .016 .. .. .. .. .. ..
±.090 max. ±.015 min.
±.060 max. ±.010 min.
0.250–0.499 .012 .008 .018 .014 .020 .016 .022 .018 .024 .020 .. .. .. ..
0.500–0.749 .014 .009 .021 .016 .023 .018 .025 .020 .027 .022 .. .. .. ..
0.750–0.999 .015 .010 .023 .018 .025 .020 .027 .022 .030 .025 .035 .030 .. ..
1.000–1.499 .018 .012 .027 .021 .029 .023 .032 .026 .036 .030 .041 .035 .. ..
1.500–1.999 .021 .014 .031 .024 .033 .026 .038 .031 .043 .036 .049 .042 .057 .050
2.000–3.999 .036 .024 .046 .034 .050 .038 .060 .048 .069 .057 .080 .068 .092 .080
4.000–5.999 .051 .034 .061 .044 .067 .050 .081 .064 .095 .078 .111 .094 .127 .110
6.000–7.999 .066 .044 .076 .054 .084 .062 .104 .082 .121 .099 .142 .120 .162 .140
8.000–9.999 .081 .054 .091 .064 .101 .074 .127 .100 .147 .120 .182 .145 .197 .170
CIRCUMSCRIBING CIRCLE SIZES 10 INCHES IN DIAMETER AND OVER
Up thru 0.124 .021 .014 .025 .018 .027 .020 .. .. .. .. .. .. .. ..
0.125–0.249 .022 .015 .026 .019 .029 .022 .035 .028 .. .. .. .. .. ..
0.250–0.499 .024 .016 .028 .020 .032 .024 .038 .030 .058 .050 .. .. .. ..
0.500–0.749 .025 .017 .030 .022 .035 .027 .049 .040 .068 .060 .. .. .. ..
0.750–0.999 .027 .018 .031 .023 .039 .030 .057 .050 .079 .070 .099 .090 .. ..
±.090 max. ±.025 min.
±.090 max. ±.015 min.
1.000–1.499 .028 .019 .033 .024 .043 .034 .069 .060 .089 .080 .109 .100 .. ..
1.500–1.999 .036 .024 .046 .034 .056 .044 .082 .070 .102 .090 .122 .110 .182 .170
2.000–3.999 .051 .034 .061 .044 .071 .054 .097 .080 .117 .100 .137 .120 .197 .180
4.000–5.999 .066 .044 .076 .054 .086 .064 .112 .090 .132 .110 .152 .130 .212 .190
6.000–7.999 .081 .054 .091 .064 .101 .074 .127 .100 .147 .120 .167 .140 .227 .200
8.000–9.999 .096 .064 .106 .074 .116 .084 .142 .110 .162 .130 .182 .150 .242 .210
10.000–11.999 .111 .074 .121 .084 .131 .094 .157 .120 .177 .140 .197 .160 .257 .220
12.000–13.999 .126 .084 .136 .094 .146 .104 .172 .130 .192 .150 .212 .170 .272 .230
14.000–15.999 .141 .094 .151 .104 .161 .114 .187 .140 .207 .160 .227 .180 .287 .240
16.000–17.999 .156 .104 .166 .114 .176 .124 .202 .150 .222 .170 .242 .190 .302 .250
18.000–19.999 .171 .114 .181 .124 .191 .134 .217 .160 .237 .180 .257 .200 .317 .260
20.000–21.999 .186 .124 .196 .134 .206 .144 .232 .170 .252 .190 .272 .210 .332 .270
22.000–24.000 .201 .134 .211 .144 .221 .154 .247 .180 .267 .200 .287 .220 .347 .280
1 These Standard Tolerances are applicable to the average profile; wider 4 Where dimensions specified are outside and inside, rather than wall
tolerances may be required for some profiles and closer tolerances may be thickness itself, the allowable deviation (eccentricity) given in Column 3
possible for others. applies to mean wall thickness. (Mean wall thickness is the average of two
2 The tolerance applicable to a dimension composed of two or more wall thickness measurements taken at opposite sides of the void.)
component dimensions is the sum of the tolerances of the component 5 In the case of Class 1 Hollow Profiles the standard wall thickness
dimensions if all of the component dimensions are indicated. tolerance for extruded round tube is applicable. (A Class 1 Hollow Profile
3 When a dimension tolerance is specified other than as an equal bilateral is one whose void is round and one inch or more in diameter and whose
tolerance, the value of the standard tolerance is that which applies to the weight is equally distributed on opposite sides of two or more equally
mean of the maximum and minimum dimensions permissible under the spaced axes.)
tolerance for the dimension under consideration. (Continued on bottom of next page)
11-6 March, 2003

Cextruded
standard tolerances/wire, rod, bar and profilesC
Examples Illustrating Use of Table 11.2, Page 11-6
Closed-Space Dimensions
All dimensions designated “Y” are classed as “metal dimensions,” and tolerances are determined
from column 2.
Dimensions designated “X” are classed as “space dimensions through an enclosed void,” and the
tolerances applicable are determined from column 4 unless 75 percent or more of the dimension
is metal, in which case column 2 applies.
Open-Space Dimensions
Tolerances applicable to dimensions “X” are

determined as follows:
1. Locate dimension “X” in column 1.
2. Determine which of columns 4–9 is
applicable, dependent on distance “A.”
3. Locate proper tolerance in column 4, 5, 6,
7, 8 or 9 in the same line as dimension “X.”
\
Dimensions “Y” are “metal dimensions”; tolerances are determined from column 2.
Distances “C” are shown merely to indicate incorrect values for determining which of columns
4–9 apply.
Tolerances applicable to dimensions “X” are determined as follows: Tolerances applicable to dimensions “X” are not determined from Table
1. Locate distance “B” in column 1. 11.2; tolerances are determined by standard tolerances applicable to
2. Determine which of columns 4–9 is applicable, dependent on angles “A.”
distance “A.”
3. Locate proper tolerance in column 4, 5, 6, 7, 8 or 9 in the same line
as value chosen in column 1.
Footnotes for page 11-7 (Continued)

6 At points less than 0.250 inch from base of leg the tolerances in Col. 9 These tolerances do not apply to
2 are applicable. space dimensions such as dimen-
7 Tolerances for extruded profiles in T3510, T4510, T6510, T73510, sions “X” and “Z” of the example
T76510 and T8510 tempers shall be as agreed upon between purchaser (right), even when “Y” is 75 percent
and vendor at the time the contract or order is entered. or more of “X.” For the tolerance
8 The following tolerances apply where the space is completely en- applicable to dimensions “X” and “Z,”
closed (hollow profiles); For the use Col. 4, 5, 6, 7, 8 or 9, dependent
width (A), the balance is the value on distance “A.”
shown in Col. 4 for the depth di-
mension (D). For the depth (D), the
tolerance is the value shown in
Col. 4 for the width dimension (A).
In no case is the tolerance for ei- bl The wall thickness tolerance for hol-
ther width or depth less than the metal dimensions (Col. 2) at the cor- low or semihollow profiles shall be as
ners. agreed upon between purchaser and
Example—Alloy 6061 hollow profile having 1 × 3 rectangular outside vendor at the time the contract or order
dimensions; width tolerance is ±0.021 inch and depth tolerance is entered when the nominal thickness
±.034 inch. (Tolerances at corners, Col. 2, metal dimensions, are of one wall is three times or greater than
±0.024 inch for the width and ±0.012 inch for the depth.) Note that that of the opposite wall.
the Col. 4 tolerance of 0.021 inch must be adjusted to 0.024 inch so bm Tolerances apply to 5xxx alloys with
that it is not less than the Col. 2 tolerance. $4.0% nominal Mg.
March, 2003 11-7

TABLE 11.3 CRound Wire and Rod - Square, Hexagonal

Diameter or Distance Across FlatsC
and Octagonal Wire and Bar
TOLERANCE3—in. plus and minus
ALLOWABLE DEVIATION FROM SPECIFIED DIMENSION ACROSS FLATS OR DIAMETER
SPECIFIED ROUND SQUARE HEXAGONAL OCTAGONAL
DIMENSION WIRE AND ROD WIRE AND BAR WIRE AND BAR WIRE AND BAR
IN 5xxx 5xxx 5xxx 5xxx
$4.0 Other $4.0 Other $4.0 Other $4.0 Other
nominal Alloys nominal Alloys nominal Alloys nominal Alloys
Mgbm Mgbm Mgbm Mgbm
Up thru 0.124 0.009 0.006 0.009 0.006 0.009 0.006 0.009 0.006
0.125-0.249 0.011 0.007 0.011 0.007 0.011 0.007 0.011 0.007
0.250-0.499 0.012 0.008 0.012 0.008 0.012 0.008 0.012 0.008
0.500-0.749 0.014 0.009 0.014 0.009 0.014 0.009 0.014 0.009
0.750-0.999 0.015 0.010 0.015 0.010 0.015 0.010 0.015 0.010
1.000-1.499 0.018 0.012 0.018 0.012 0.018 0.012 0.018 0.012
1.500-1.999 0.021 0.014 0.021 0.014 0.021 0.014 0.021 0.014
2.000-3.999 0.036 0.024 0.036 0.024 0.036 0.024 0.036 0.024
4.000-5.999 0.051 0.034 0.051 0.034 0.051 0.034 0.051 0.034
6.000-7.070 0.066 0.044 0.066 0.044 0.066 0.044 0.066 0.044
7.071-7.999 0.066 0.044 0.081 0.054 0.066 0.044 0.066 0.044
8.000-8.659 0.081 0.054 0.096 0.064 0.081 0.054 0.081 0.054
8.660-8.999 0.081 0.054 0.096 0.064 0.096 0.064 0.081 0.054
9.000-9.238 0.081 0.054 0.096 0.064 0.096 0.064 0.081 0.054
9.239-9.999 0.081 0.054 0.096 0.064 0.096 0.064 0.096 0.064
10.000-11.999 0.111 0.074 0.111 0.074 0.111 0.074 0.111 0.074
12.000-13.999 0.126 0.084 0.126 0.084 0.126 0.084 0.126 0.084
14.000-15.999 0.141 0.094 0.141 0.094 0.141 0.094 0.141 0.094
Note: Shaded tolerances denote products with a circumscribing circle size of 10 inches in diameter and over.
For all numbered footnotes, see pages 11-6 and 11-7.
TABLE 11.4 C
Thickness or Width (Distance Across Flats)C
Rectangular Wire and Bar
TOLERANCE—in. plus and minus
ALLOWABLE DEVIATION FROM SPECIFIED
WIDTH OR THICKNESS ACROSS FLATS
SPECIFIED 5xxx 5xxx
DIMENSION $4.0 Other $4.0 Other
IN. nominal Alloys nominal Alloys
Mgbm Mgbm
Up thru 0.124 0.009 0.006 0.021 0.014
0.125-0.249 0.011 0.007 0.022 0.015
0.250-0.499 0.012 0.008 0.024 0.016
0.500-0.749 0.014 0.009 0.025 0.017
0.750-0.999 0.015 0.010 0.027 0.018
1.000-1.499 0.018 0.012 0.028 0.019
1.500-1.999 0.021 0.014 0.036 0.024
2.000-3.999 0.036 0.024 0.051 0.034
4.000-5.999 0.051 0.034 0.066 0.044
6.000-7.999 0.066 0.044 0.081 0.054
8.000-9.999 0.081 0.054 0.096 0.064
10.000-11.999 .. .. 0.111 0.074
12.000-13.999 .. .. 0.126 0.084
14.000-15.999 .. .. 0.141 0.094
16.000-17.999 .. .. 0.156 0.104
18.000-19.999 .. .. 0.171 0.114
20.000-21.999 .. .. 0.186 0.124
22.000-24.000 .. .. 0.201 0.134
Note: Shaded tolerances denote products with a circumscribing circle size of 10 inches in diameter and over.
For numbered footnote, see page 11-7.
11-8 March, 2003

Cextruded
TABLE 11.5 Length1CWire, Rod, Bar and Profiles

TOLERANCE—in. plus
SPECIFIED DIAMETER (WIRE AND ROD): ALLOWABLE DEVIATION FROM SPECIFIED LENGTH
SPECIFIED WIDTH (BAR):
CIRCUMSCRIBING SPECIFIED LENGTH—ft.
CIRCLE DIAMETER4: Over Over
(PROFILES) Up
12 30 Over
in. thru
thru thru 50
12
30 50
Up thru 2.999 1'8 1'4 3'8 1
3.000–7.999 3'16 5'16 7'16 1
8.000 and over 1'4 3'8 1'2 1
TABLE 11.6 Straightness1 CRod, Bar and Profiles

TOLERANCE3—in.
ALLOWABLE DEVIATION (D) FROM STRAIGHT9
SPECIFIED DIAMETER
(ROD): SPECIFIED
THICKNESS
SPECIFIED WIDTH (RECTANGLES):
(BAR):
PRODUCT TEMPER MINIMUM D
CIRCUMSCRIBING THICKNESS:
CIRCLE DIAMETER4: (PROFILES)
(PROFILES)
in.
IN TOTAL LENGTH OR IN ANY
in.
MEASURED
SEGMENT OF ONE FT.
OR MORE OF TOTAL LENGTH
All except O
TX5102 All .. .0125 × Measured length, ft.
Rod and Square, TX5112
Hexagonal
and Octagonal O 0.500 and over .. .050 × Measured length, ft.
Bar TX5102 0.500 and over .. .050 × Measured length, ft.
TX5112 0.500 and over .. .0125 × Measured length, ft.
All except O Up thru 1.499 Up thru 0.0947 .050 × Measured length, ft.
TX5102 0.095 and over .0125 × Measured length, ft.
TX5112 1.500 and over All .0125 × Measured length, ft.
Rectangular
Bar O Over 0.500 0.500 and over .050 × Measured length, ft.
TX5102 Over 0.500 0.500 and over .050 × Measured length, ft.
TX5112 Over 0.500 0.500 and over .0125 × Measured length, ft.
All except O Up thru 1.499 Up thru 0.0947 .050 × Measured length, ft.
TX51025 0.095 and over .0125 × Measured length, ft.
TX5112 1.500 and over All .0125 × Measured length, ft.
Profiles O 0.500 and over Up thru 0.0947 .200 × Measured length, ft.
0.095 and over .050 × Measured length, ft.
TX5112 0.500 and over Up thru 0.0947 .050 × Measured length, ft.
0.095 and over .0125 × Measured length, ft.
Footnotes for Pages 11-9 and 11-10

1 These Standard Tolerances are applicable to the average profile; 6 See Standards Section (6) for Application of Twist Limits; for addi-
wider tolerances may be required for some profiles, and closer toler- tional information, see Aluminum Association publication “Understanding
ances may be possible for others. Aluminum Extrusion Tolerances”.
2 TX510 and TX511 are general designations for the following stress 7 Applies only if the thickness along at least 1'3 of the total perimeter is
relieved tempers: T3510, T4510, T61510, T6510, T8510, T73510, 0.094 or less. Otherwise use the tolerance shown for 0.095 and over.
T76510 and T3511, T4511, T61511, T6511, T8511, T73511, T76511, 8 Tolerance for “O” temper material is four times the standard toler-
respectively. ances shown.
3 When weight of piece on the flat surface minimizes deviation. 9 Straightness must be met in all orientations, including orientations
4 The circumscribing circle diameter is the diameter of the smallest which are not self-supporting.
circle that will completely enclose the cross section of the extruded
product.
5 Tolerances for T3510, T4510, T6510, T73510, T76510, and T8510
tempers shall be as agreed upon between purchaser and vendor at the
time the contract or order is entered.
March, 2003 11-9

TABLE 11.7 Twist16CBar and Profiles

TOLERANCE3—Degrees
ALLOWABLE DEVIATION FROM STRAIGHT
SPECIFIED SPECIFIED
WIDTH THICKNESS
(BAR): (RECTANGLES):
PRODUCT TEMPER CIRCUMSCRIBING MINIMUM

CIRCLE DIAMETER4: THICKNESS:
(PROFILES) (PROFILES)
in. in. IN TOTAL LENGTH OR IN

MAXIMUM
ANY MEASURED SEGMENT
FOR TOTAL
OF ONE FT. OR MORE
LENGTH
OF TOTAL LENGTH
All except O Up thru 1.499 All 1 × Measured length, ft. 7
TX5102 1.500–2.999 All ½ × Measured length, ft. 5
TX5112 3.000 and over All ¼ × Measured length, ft. 3
0.500–1.499 0.500 and over 3 × Measured length, ft. 21
O 1.500–2.999 0.500 and over 1½ × Measured length, ft. 15
Bar 3.000 and over 0.500 and over ¾ × Measured length, ft. 9
TX5102 0.500–2.999 0.500 and over 1½ × Measured length, ft. 7
3.000 and over 0.500 and over ½ × Measured length, ft. 5
0.500–1.499 0.500 and over 1 × Measured length, ft. 7
TX5112 1.500–2.999 0.500 and over ½ × Measured length, ft. 5
3.000 and over 0.500 and over ¼ × Measured length, ft. 3
All except O Up thru 1.499 All 1 × Measured length, ft. 7
TX51025 1.500–2.999 All ½ × Measured length, ft. 5
TX5112 3.000 and over All ¼ × Measured length, ft. 3
0.500 and over Up thru 0.094 7 3 × Measured length, ft. 21
O 0.500–1.499 0.095 and over 3 × Measured length, ft. 21
Profiles 1.500–2.999 0.095 and over 1½ × Measured length, ft. 15
3.000 and over 0.095 and over ¾ × Measured length, ft. 9
0.500 and over Up thru 0.094 7 1 × Measured length, ft. 7
TX5112 0.500–1.499 0.095 and over 1 × Measured length, ft. 7
1.500–2.999 0.095 and over ½ × Measured length, ft. 5
3.000 and over 0.095 and over ¼ × Measured length, ft. 3
TABLE 11.8 Flatness (Flat Surfaces)1CBar, Solid Profiles and Semihollow Profiles
EXCEPT FOR PROFILES IN O8, T3510, T4510, T6510, T73510, T76510 and T8510 TEMPERS5
SURFACES WIDTHS UP THRU 1 INCH OR ANY 1 INCH INCREMENT OF

WIDER SURFACES
Maximum Allowable Deviation D = TOLERANCE (in.)
WIDTHS OVER 1 INCH

Maximum Allowable Deviation D = TOLERANCE × W (in.)
SURFACE WIDTH—in.
MINIMUM THICKNESS
UP 6.000 8.000 10.000 12.000 14.000 16.000 18.000 20.000 22.000 24.000
OF METAL FORMING
TO TO TO TO TO TO TO TO TO TO AND
THE SURFACE
5.999 7.999 9.999 11.999 13.999 15.999 17.999 19.999 21.999 23.999 UP
in.
TOLERANCE
Up thru 0.124 .004 .006 .010 .014 .. .. .. .. .. .. ..
0.125-0.187 .004 .006 .008 .012 .014 .014 .014 .. .. .. ..
0.188-0.249 .004 .006 .008 .010 .012 .012 .012 .014 .014 .. ..
0.250-0.374 .004 .006 .006 .008 .010 .010 .012 .012 .012 .014 ..
0.375-0.499 .004 .004 .006 .008 .008 .008 .010 .010 .010 .012 .014
0.500-0.749 .004 .004 .006 .006 .008 .008 .008 .008 .010 .010 .012
0.750-0.999 .004 .004 .006 .006 .008 .008 .008 .008 .008 .008 .010
1.000-1.499 .004 .004 .004 .006 .006 .008 .008 .008 .008 .008 .008
1.500-1.999 .004 .004 .004 .004 .006 .006 .006 .008 .008 .008 .008
2.000 and up .004 .004 .004 .004 .004 .006 .006 .006 .008 .008 .008
For all numbered footnotes, see page 11-9.
11-10 March, 2003

Cextruded
PROFILES EXCEPT FOR PROFILES IN Obl, T3510, T4510, T6510, T73510,
TABLE 11.9 Flatness (Flat Surfaces)1 HOLLOW
T76510 and T8510 TEMPERS4
SURFACES WIDTHS UP THRU 1 INCH OR ANY 1 INCH INCREMENT OF WIDER SURFACES

Maximum Allowable Deviation D = TOLERANCE (in.)
WIDTHS OVER 1 INCH

Maximum Allowable Deviation D = TOLERANCE × W (in.)
SURFACE WIDTH—in.
MINIMUM THICKNESS
UP 6.000 8.000 10.000 12.000 14.000 16.000 18.000 20.000 22.000 24.000
OF METAL FORMING
TO TO TO TO TO TO TO TO TO TO AND
THE SURFACE
5.999 7.999 9.999 11.999 13.999 15.999 17.999 19.999 21.999 23.999 UP
in.
TOLERANCE
Up thru 0.124 .006 .008 .012 .016 .. .. .. .. .. .. ..
0.125-0.187 .006 .008 .010 .014 .016 .. .. .. .. .. ..
0.188-0.249 .004 .006 .010 .012 .014 .014 .014 .016 .. .. ..
0.250-0.374 .004 .006 .008 .010 .012 .012 .012 .014 .014 .016 ..
0.375-0.499 .004 .006 .008 .010 .010 .010 .012 .012 .012 .014 .016
0.500-0.749 .004 .004 .006 .008 .008 .008 .010 .010 .012 .012 .014
0.750-0.999 .004 .004 .006 .006 .008 .008 .008 .008 .010 .010 .012
1.000 and up .004 .004 .004 .006 .006 .008 .008 .008 .008 .008 .008
TABLE 11.10 Surface Roughness18CWire TABLE 11.14 Angularity15CBar and Profiles

Rod, Bar & Profiles TOLERANCE
Degrees plus and minus
ALLOWABLE DEPTH
SPECIFIED SECTION THICKNESS ALLOWABLE DEVIATION FROM
OF CONDITIONS2
in. SPECIFIED ANGLE
in. max.
Up thru 0.063 .0015
0.064-0.125 .002 MINIMUM
0.126-0.188 .0025 SPECIFIED
0.189-0.250 .003 TEMPER LEG
0.251-0.500 .004 THICKNESS
0.501- and over .008 in.
TABLE 11.11 Contour (Curved Surfaces)13C RATIO:67LEG OR SURFACE

Profiles LENGTH TO LEG OR METAL
THICKNESS
Temper 1 and less Over 1 thru 40
Col. 1 Col.2 Col.3
All except Up thru 0.187 1 2
O, 0.188–0.749 1 1½
All except Allowable deviation from specified contour: 0.005 inch TX5104 0.750 and over 1 1
O, per inch of chord length; 0.005 inch minimum. Not appli- Up thru 0.187 3 6
TX5104 cable to contours with chord length 6 inch and over. O 0.188–0.749 3 4½
Allowable deviation from specified contour: 0.015 inch 0.750 and over 3 3
O per inch of chord length; 0.015 inch minimum. Not appli-
cable to contours with chord length 6 inches and over. 1 These Standard Tolerances are applicable to the average profile; wider
tolerances may be required for some profiles, and closer tolerances may be
possible for others.
TABLE 11.12 Squareness of Cut Ends1 2 Conditions include die lines and handling marks.
3 As measured with a contour gauge whose surface is limited to a maximum sub-
Allowable deviation from square: 1 degree tended angle of 90 degrees. Extruded curved surfaces comprising more than a 90-
degree subtended angle are checked by sliding the gauge across the surface, thus
TABLE 11.13 Corner and Fillet Radii1C checking two or more 90-degree portions of the surface. Extruded profile surfaces
comprising arcs formed by two or more radii require the use of a separate contour
Bar and Profiles gauge for each portion of the surface formed by an individual radius.
4 Tolerances for T3510, T4510, T6510, T73510, T76510 and T8510 tempers
TOLERANCE—in. shall be as agreed upon between the purchaser and vendor and at the time the
contract or order is entered.
ALLOWABLE DEVIATION 5 Angles are measured with protractors or with gauges.
FROM SPECIFIED RADIUS As illustrated, a four-point contact system is used, two
contact points being as close to the angle vertex as prac-
tical, and the others near the ends of the respective
SPECIFIED RADIUS9 surfaces forming the angle. Between these points of
in. measurement surface flatness is the controlling tolerance.
6 When the area between the surface forming an angle is all metal, values in
column 2 apply if the larger surface length to metal thickness ratio is 1 or less.
7 When two legs are involved the one having the larger ratio determines the
applicable column.
Difference between radius 8 Not applicable to 2219 alloy extrusions. Most profiles in 2219 alloy will have
A and specified radius die lines about twice the depth shown in the table; however, for each profile the
Sharp corners + 1'64 supplier should be contacted for the roughness value to apply.
0.016–0.187 ± 1'64 9 If unspecified, the radius shall be 1'32 in. maximum including tolerances.
0.188 and over ±10% bl Tolerance for “O” temper material is four times the standard tolerances shown.
March, 2003 11-11

Extrudex Aluminum Catalogue PDF

Uploaded by

Copyright:

Available Formats

Extrudex Aluminum Catalogue PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Extrudex Aluminum Catalogue PDF

Uploaded by

Copyright:

Available Formats

http://www.extrudex.

Revised on: April 18, 2019

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

Angles, Equal Legs

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

Angles, Equal Legs

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

Angles, Equal Legs

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

Angles, Equal Legs

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

Angles, Unequal Legs

Angles, Unequal Legs

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

Angles, Unequal Legs

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

Angles, Unequal Legs

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

Angles, Unequal Legs

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

I-Beam and H-Beam

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

I-Beam and H-Beam

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

Round Tubes and Pipes

Round Tubes and Pipes

Round Tubes and Pipes

Round Tubes and Pipes

Round Tubes and Pipes

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

(*) - 1/2 Commercial Tolerances Revised on: April 18, 2019

MECHANICAL PROPERTY LIMITS-EXTRUDED ROD, BAR AND PROFILES (SHAPES)

ALLOY &TEMPER SPECIFIED AREA TENSILE STRENGTH - KSI ELONGATION

TABLE 11.2 CProfiles1

TOLERANCE23—in. plus and minus

±10% of specified dimension;

Up thru 0.124 .009 .006 .013 .010 .015 .012 .. .. .. .. .. .. .. ..

±.060 max. ±.010 min.

±15% of specified dimension;

±.090 max. ±.015 min.

11-6 March, 2003

Tolerances applicable to dimensions “X” are

Footnotes for page 11-7 (Continued)

March, 2003 11-7

TABLE 11.3 CRound Wire and Rod - Square, Hexagonal