Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 210 views

    116 User

    Uploaded by

    Mohamed Yahya
    The DKG-116 is a low cost manual and remote start genset control unit that can start and stop a generator manually using buttons or remotely via a signal. It monitors generator voltage, frequency, and battery voltage. It protects the generator and indicates faults. It has optional inputs and outputs and stores total run hours. Precautions must be followed for safe installation and use. It has programmable parameters and technical specifications.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    116 User

    Uploaded by

    Mohamed Yahya
    210 views4 pages
    The DKG-116 is a low cost manual and remote start genset control unit that can start and stop a generator manually using buttons or remotely via a signal. It monitors generator voltage, frequency, and battery voltage. It protects the generator and indicates faults. It has optional inputs and outputs and stores total run hours. Precautions must be followed for safe installation and use. It has programmable parameters and technical specifications.

    Original Description:

    This 116 manaul

    Original Title

    116_USER

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The DKG-116 is a low cost manual and remote start genset control unit that can start and stop a generator manually using buttons or remotely via a signal. It monitors generator voltage, frequency, and battery voltage. It protects the generator and indicates faults. It has optional inputs and outputs and stores total run hours. Precautions must be followed for safe installation and use. It has programmable parameters and technical specifications.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    210 views4 pages

    116 User

    Uploaded by

    Mohamed Yahya
    The DKG-116 is a low cost manual and remote start genset control unit that can start and stop a generator manually using buttons or remotely via a signal. It monitors generator voltage, frequency, and battery voltage. It protects the generator and indicates faults. It has optional inputs and outputs and stores total run hours. Precautions must be followed for safe installation and use. It has programmable parameters and technical specifications.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    DKG-116 User Manual V-03 (30.03.

    2011)

    DKG-116 MANUAL AND


    REMOTE START UNIT

    DESCRIPTION MEASUREMENTS

    The DKG-116 is a low cost Generator Volts: L1-N, L2-N, L3-N


    gasoline/diesel genset control unit Generator Volts: L1-L2, L2-L3, L3-L1
    designed to start and stop a genset both Generator Frequency
    manually and remotely. Battery Voltage
    The manual control is made using RUN
    and STOP pushbuttons on the front
    OPTIONS
    panel. The remote control is made via
    Auxiliary output (negative pulling).
    REMOTE START input signal.
    Magnetic pickup input.
    When RUN button is pressed or a Remote
    Start signal arrives, the engine will be FEATURES
    cranked up to 3 times. When it runs, the
    crank relay will be immediately deactivated Both Manual and remote control
    and after Holdoff timer delay, fault Generator protection
    checking will be enabled. When the engine
    is running, if a fault condition is detected Built in alarms and warnings
    then the engine is shutdown immediately Remote Start operation available
    and the unit indicates the source of the True RMS measurements
    failure through related alarm led.
    Tamper-proof engine hours display
    If the Remote Start signal disappears or Field adjustable parameters
    the STOP button is pressed or the genset
    will immediately stop. High current Fuel and Crank outputs
    Optional auxiliary output
    The MENU button selects display
    parameter scroll and allows program Optional magnetic pickup input
    mode entry and lamp test functions. Digital inputs: 4
    The total engine run hours is kept in a Survives cranking dropouts
    tamper-proof non-erasable memory which Sealed front panel
    is not affected by power failures.
    Standard panel dimensions: 96x48mm
    Plug-in connection system
    DKG-116 User Manual V-03 (30.03.2011)

    PRECAUTIONS FOR INSTALLATION AND SAFE USE

    Failure to follow below instructions will result in death or


    serious injury.

     Circuit breakers must be connected serially to BAT+, PHASE-L1, PHASE-L2 and PHASE-
    L3 terminals, in close proximity of the unit.
     Fuses must be of fast type with a maximum rating of 6A.
     Disconnect all power before working on equipment .
     When the genset is running, do not touch terminals.
     Do not try to clean the device with solvent or the like. Only clean with a dump cloth.
     Verify correct terminal connections when wiring.
     Electrical equipment should be serviced only by competent service personnel. No
    responsibility is assured by the manufacturer or any of its subsidiaries for any
    consequences arising out of the use of this material.
     Only for front panel mounting.

    CONNECTION DIAGRAM
    DKG-116 User Manual V-03 (30.03.2011)

    PROGRAMMING

    Both ‘High Temperature’ and ‘Emergency Stop’ inputs must be connected


    to ‘Battery negative’ prior to enter the programming mode.

    The unit offers 12 programmable parameters listed below.


    FACTORY
    NO SYMBOL RANGE DESCRIPTION
    SET
    1 70-500 V 170 V Low AC voltage shutdown limit
    2 70-500 V 300V High AC voltage shutdown limit
    3 0-1000 50 MPU crank cut frequency divided by 4
    4 0-1 0 Nominal frequency: 0=50Hz 1=60Hz
    5 0-1 0 Oil input: 0=pressure switch 1=level switch
    6 0-1 0 Fuel output type 0:Fuel 1:Stop
    0-3 0 Relay 3 function
    7
    0:Alarm 1:Choke 2:Stop 3:Preheat
    8 0-15 sec 0 Choke timer in seconds
    9 0-15 sec 10 Preheat timer in seconds
     0-7 0 Connection topology:
    0=1phase 1=2phases 2=3 phases 3=3 phases ,
    center tapped delta (voltage checks on first 2
    10
    phases only)
    4..7= same as 0..3, but voltages are not
    displayed
    11 0-15 sec 5 Under/over voltage delay timer
    12  - - Phase L1-N calibration value
    13  - - Phase L2-N calibration value
    14  - - Phase L3-N calibration value
    The program mode is entered by long-pressing the MENU button. Each depression of the MENU
    button will switch to the next parameter.
    Another long press will enable the lamp test mode. Then any depression of MENU button will return
    the display to normal mode.
    If no key is pressed, then the unit will return to normal display mode with a delay.
    1- When genset is in off mode; press MENU button for 5 sec to
    MENU
    enter program mode and display the Low AC Voltage limit.

    2- Press RUN or STOP buttons until requested value is displayed.


    RUN STOP

    N 3- Press MENU button for saving the Low AC Voltage limit and
    MENU displaying the next program parameter.

    4- Press RUN or STOP buttons until requested value is displayed.


    RUN STOP

    N
    5- Press MENU button for saving the parameter and displaying
    MENU the next parameter.
    6- Repeat steps 4 and 5 as required.
    7- Any time on settings, press MENU button for 3 sec. to exit from
    RUN STOP
    program mode.
    N
    DKG-116 User Manual V-03 (30.03.2011)

    TECHNICAL SPECIFICATIONS DIESEL ENGINE SELECTION


    Alternator voltage: 15 to 300 V-AC (Ph-N)
    Alternator frequency: 50 or 60 Hz nominal. In order to control
    Measurement Accuracy: 0.5% + 1 digit
    diesel engines,
    connect a conductive
    Overspeed: nominal frequency + 14%
    wire to between
    (+24% overshoot)
    terminals 1 and 3.
    Underspeed: 30 Hz
    Crank time: 10 sec.
    Crank rest: 10 sec.
    Crank attempts: 3 PANEL CUTOUT DIMENSIONS
    Stop timer: 10 sec.
    Holdoff timer: 10 sec.

    44mm
    DC Supply Range: 9.0 to 16.0 V-DC
    Cranking dropouts: survives 0 V for 100ms.
    Typical Standby Current: 12mA-DC (display off)
    Maximum Operating Current: 130 mA-DC
    Fuel and Crank outputs: 10A @ 12V-DC
    Auxiliary Output: 1A @ 12V-DC (negative pulling
    protected semiconductor output)
    92mm
    Magnetic pickup Input: 1.5 to 30Vpp
    Operating temp.: -40°C (-40°F) to 80 °C (176°F).
    Maximum humidity: 95% non-condensing. PACKAGING INFORMATION
    Dimensions: 102 x 55 x 40 mm (WxHxD)
    Pieces per Package: 24
    Packed weight: 140 g
    Package Size: 280 x 170 x 215mm (LxWxH)
    Case Material: High Temp. ABS/PC (UL94-V0)
    Package Weight: 3.6 kg
    IP Protection: IP65 (front panel), IP30 (rear)
    Conformity (EU directives)
    -2006/95/EC (low voltage)
    -2004/108/EC (EMC)
    Norms of reference:
    EN 61010 (safety requirements)
    EN 61326 (EMC requirements)

    DATAKOM Electronics Ltd.


    Tel: +90-216-466 84 60 Fax: +90-216-364 65 65 e-mail: datakom@datakom.com.tr http: www.datakom.com.tr

    You might also like