Leroy Motor 4850f - en PDF

Installation & maintenance
Three-phase induction
motors
LS / LSES, aluminium motors
FLSES, cast iron motors
PLSES, IP23 drip-proof motors
Part number: 4850 en - 2018.11 / f

IMPORTANT
These symbols appear in this document whenever it is important to take special precautions during installation,
operation, maintenance or servicing of the motors.
It is essential that electric motors are installed by experienced, qualified and authorized personnel.
In accordance with the main requirements of EU Directives, the safety of people, animals and property should be
ensured when fitting the motors into machines.
Particular attention should be given to equipotential ground or earthing connections.
The noise level of the machines, measured under standard conditions, conforms to the requirements of the standard.
The following preliminary precautions must be taken before working on any stationary device:
• mains voltage disconnected and no residual voltage present
• careful examination of the causes of the stoppage (blocked transmission - loss of phase
- cut-out due to thermal protection - lack of lubrication, etc)
2 Installation and maintenance - Three-phase induction motors

4850 en - 2018.11 / f

Dear Customer,
You have just acquired a LEROY-SOMER motor.
This motor benefits from the experience of one of the largest manufacturers in the world, using state-of-the-art technology in
automation, specially selected materials and rigorous quality control. As a result, the regulatory authorities have awarded our motor
factories the ISO 9001 - Edition 2015 international certificate.
We thank you for making this choice, and would ask you to read the contents of this manual.
By observing a few essential rules, you will ensure problem-free operation for many years.
MOTEURS LEROY-SOMER
CE conformity
Our motors conform to standard EN/IEC 60034-1, and to the directives 2014/35/EU (low voltage) modified by Directive 2006/42/EC
(machine), which is demonstrated by their marking with the symbol
NOTE :
LEROY-SOMER reserves the right to modify the characteristics of its products at any time in order to incorporate the latest technological
developments. The information contained in this document may therefore be changed without notice.
Copyright 2018 : MOTEURS LEROY-SOMER
This document is the property of MOTEURS LEROY-SOMER.
It may not be reproduced in any form without prior authorization.
All brands and models have been registered and patents applied for.
Installation and maintenance - Three-phase induction motors 3

4850 en - 2018.11 / f

CONTENTS INDEX
1 - RECEIPT................................................................ 5 Adjustment............................................................................8
1.1 - Identification.............................................................5 Alarms - early warning.........................................................12
1.2 - Storage....................................................................6 Assembly...............................................................................6
Balancing..............................................................................7
2 - ASSEMBLY............................................................ 6
Belts......................................................................................9
2.1 - Checking the insulation............................................6 Built-in thermal protection....................................................12
2.2 - Location - ventilation................................................7
2.3 - Coupling...................................................................7 Cable gland.........................................................................13
2.4 - Electrical guidelines...............................................10 Cables: cross-section................................................... 14 - 15
2.5 - Mains connection...................................................13 Capacitors........................................................................... 11
Connection..........................................................................15
3 - ROUTINE MAINTENANCE.................................. 16 Connection diagrams...........................................................15
3.1 - Lubrication.............................................................16 Corrective maintenance.......................................................22
3.2 - Bearing maintenance.............................................20 Coupling........................................................................... 7 - 8
Coupling sleeves ..................................................................8
4 - PREVENTIVE MAINTENANCE............................ 20 Digistart...............................................................................10
Direction of rotation..............................................................15
5 - TROUBLESHOOTING GUIDE............................. 21 Draining condensation ........................................................16
6 - CORRECTIVE MAINTENANCE: GENERAL....... 22 Earth terminal......................................................................15

6.1 - Dismantling the motor............................................22 Earthing............................................................................... 11
6.2 - Checks before reassembly.....................................22 European directives...............................................................5
6.3 - Mounting the bearings on the shaft.........................22 Frequency inverter............................................................... 11
6.4 - Reassembling the motor......................................... 22
6.5 - Reassembling the terminal box..............................22 Greasing - Grease nipples....................................... 6 - 16 - 20
Handling................................................................................7
7 - POSITION OF LIFTING RINGS............................ 23
Identification..........................................................................5
8 - SPARE PARTS..................................................... 24 Inertia flywheel.......................................................................8
Insulation ..............................................................................6
9 - RECYCLING......................................................... 24 Lifting rings..........................................................................23
Location ................................................................................7
Logos ....................................................................................5
Lubrication...........................................................................16
DISMANTLING AND REASSEMBLY
PROCEDURES Mains connection.................................................................13
Nameplate.............................................................................5
10 - LS/LSES MOTORS............................................ 26
Power..................................................................................10
10.1 - 71 to 160 MP/LR motors.......................................26
Power supply.......................................................................15
10.2 - 160 M/L/LU, 180 MT/LR motors........................... 28
Preventive maintenance..................................................... 20
10.3 - 180 L/LUR, 200 L/LR/LU, 225 ST/MT/MR,
Protection............................................................................12
250 MZ motors.....................................................30
Pulleys...................................................................................9
10.4 - 225 MG, 250 ME/MF, 280 SC/MC/SD/MD,
315 SN motors......................................................32 Receipt..................................................................................5
10.5 - 280 SU/SK/MK, 315 (except SN) motors..............34 Routine maintenance.......................................................... 20
11 - FLS/FLSES MOTORS........................................ 36 Shields.......................................................................... 16 - 20

Slide rails...............................................................................9
11.1 - 80 to 132 motors...................................................36
Space heaters.....................................................................12
11.2 - 160, 180 MR motors.............................................38
Spare parts......................................................................... 24
11.3 - 180 M/L/LUR, 200 LU, 225 MR/SR motors........... 40
Starting................................................................................10
11.4 - 225 M to 280 motors.............................................42
Storage..................................................................................6
11.5 - 315 to 355 LD motors...........................................44
Terminal box .......................................................................13
12 - PLS/PLSES MOTORS....................................... 46 Terminal box: tightening the nuts.........................................15
12.1 - 180 LG/LGU, 200 M/L/LP/LU/LR, Tie rods: tightening ..............................................................22
225 MR motors.....................................................46 Tolerances.............................................................................8
Troubleshooting...................................................................21
12.2 - 225 MG, 250, 280 SC/SD/MC/MD motors............48
12.3 - 280 MG, 315 motors.............................................50 Ventilation..............................................................................7

4850 en - 2018.11 / f
RECEIPT
1 - RECEIPT
On receipt of your motor, check that it has not suffered any damage in transit.
If there are obvious signs of knocks, contact the carrier (you may able to claim on their insurance) and after a visual check, turn the
motor by hand to detect any malfunction.
1.1 - Identification
As soon as you receive the motor, check that the nameplate on the machine conforms to your order.
* Other logos may be used as an optional extra:

This must be agreed prior to ordering.
Definition of symbols used on nameplates:

Legal mark of conformity
of product to the requirements
of European Directives
MOT 3 ~ : 3-phase A.C. motor IP55 IK08 : Index of protection Bearings

LSES : Series I cl. F : Insulation class F
DE : Drive end bearing
132 : Frame size 40°C : Ambient operating
temperature NDE : Non drive end bearing
S : Housing symbol
S1 : Duty - Duty (operating) factor g : Amount of grease at each
kg : Weight regreasing (in g)
Motor no. V : Supply voltage h : Regreasing interval
(in hours)
123456 : Motor batch number Hz : Supply frequency
POLYREX EM103 : Type of grease
E : Month of production min -1
: Revolutions per minute (rpm)
11 : Year of production kW : Rated output power : Vibration level
A
001 : Serial number cos ϕ : Power factor
: Balancing mode
H
IE2 : Efficiency class A : Rated current
83.8% : Efficiency at 4/4 load Δ : Delta connection
Y : Star connection
Please quote when

ordering spare parts

4850 en - 2018.11 / f
ASSEMBLY
1.2 - Storage 2.1 - Checking the insulation

Prior to commissioning, machines should be stored in a
horizontal position: Before starting the motor, it is advisable to check
- Away from humidity: at relative humidity levels greater than the insulation between the phases and earth,
90% the machine insulation can drop very rapidly, to just above and between phases.
zero at around 100%. The state of the anti-rust protection on
unpainted parts should be monitored.
This check is essential if the motor has been stored for longer
For very long storage periods the motor can be placed in a
than 6 months or if it has been kept in a damp atmosphere.
sealed package (for example heat-shrunk plastic) containing
This measurement must be carried out using a megohmmeter
sachets of desiccant.
at 500V D.C. (do not use a magnetoelectric system).
- Away from frequent significant variations in temperature, to
It is better to carry out an initial test at 30 or 50 volts and if the
avoid the risk of condensation. During storage the drain plugs
must be removed to allow condensation water to escape. insulation is greater than 1 megohm, carry out a second test at
- If the area is subject to vibration, try to reduce the effect of this 500 volts for 60 seconds. The insulation value must be at least
vibration by placing the motor on a damping support (rubber 10 megohms in cold state.
plate or similar) and turn the rotor a fraction of a turn once a If this value cannot be achieved, or if the motor may have been
fortnight to prevent the bearing rings from becoming marked. splashed with water or salt spray, or kept for a long period in a
- Do not discard the rotor locking device (where there are roller very humid place or if it is covered with condensation, it is
bearings). advisable to dry the stator for 24 hours in a drying oven at a
Even if the motor has been stored in the correct conditions, temperature of between 110°C and 120°C.
certain checks must be carried out before it is started up: If it is not possible to place the motor in a drying oven:
- Switch on the motor, with the rotor locked, at 3-phase A.C.
Greasing voltage reduced to approximately 10% of the rated voltage, for
Bearings which cannot be regreased 12 hours (use an induction regulator or a reduction transformer
Maximum storage: 3 years. After this time, replace the bearings with adjustable outlets). For slip-ring motors, this test should
(see section 6.3). be performed with the rotor short-circuited.
Bearings which can be regreased - Or supply the 3 phases in series with a D.C. current, with the
Grease Grease voltage at 1 to 2% of the rated voltage (use a D.C. generator
grade 2 grade 3 with independent excitation or batteries for motors of less than
22 kW).
less than less than The motor can be commissioned
6 months 1 year without regreasing.
- NB: The A.C. current must be monitored using a clamp
ammeter, and the D.C. current using a shunt ammeter. This
more than more than Regrease before commissioning,
6 months 1 year as described in section 3.1 current must not exceed 60% of the rated current.
Storage period
less than less than It is advisable to place a thermometer on the motor housing: if
1 year 2 years the temperature exceeds 70 °C, reduce the indicated voltage
more than more than Dismantle the bearing or current by 5% of the original value for every 10° difference.
1 year 2 years and - Clean it While it is drying, all the motor orifices must be open (terminal
less than less than - Replace the grease completely box, drain holes).
5 years 5 years
more than more than Change the bearing
5 years 5 years - Regrease it completely
M
Greases used by LEROY-SOMER

(see nameplate): - grade 3: ESSO UNIREX N 3
- POLYREX EM103
2 - ASSEMBLY
For all insulation or dielectric tests, it is advisable to
In all cases, compatibility of the motor and its earth the thermal probes and/or accessories.
environment must be guaranteed before its installation
and also throughout its life.
Warning: If the high voltage test, carried out at

Electric motors are industrial products. the factory before dispatch, needs to be repeated,
They must therefore be installed by it should be performed at half the standard voltage, ie.:
qualified, experienced and authorized personnel. The 1/2 (2U+1000V). Check that the capacitive effect
safety of people, animals and property must be ensured resulting from the high voltage test is eliminated before
when fitting the motors into machines (please refer to connecting the terminals to earth.
current standards).

4850 en - 2018.11 / f
ASSEMBLY
Positioning
Prior to commissioning for all motors: The motor must be mounted in the position specified on
Rotate the motor at no load (no mechanical load) the order, on a base which is rigid enough to prevent
for 2 to 5 minutes, checking that there is no abnormal distortion and vibration.
noise. If there is any abnormal noise, see section 5. Where the motor feet have six fixing holes, it is preferable to
use those which correspond to the standard dimensions for the
motor power rating (refer to the technical catalogue for
2.2 - Location - ventilation induction motors), or, failing that, to those shown at B2.
2.2.1 - TEFV motors
Our motors are cooled in accordance with method IC 411
(standard IEC 34-6), i.e. «machine cooled by its surface, using
the ambient fluid (air) flowing along the machine».
The fan at the non drive end cools the motor. Air is sucked in
through the grille of a fan cover (which provides protection
against the risk of direct contact with the fan in accordance with
B 1
standard IEC 34-5) and blown along the housing fins to ensure B 2
thermal equilibrium of the motor whatever the direction of

rotation.
Ensure there is easy access to the terminal box, the
1/4 H min condensation drain plugs and, if appropriate, to the grease
(with a minimum nipples.
distance of 25 mm)
Use lifting equipment which is compatible with the weight of the
motor (indicated on the nameplate).
When the motor is fitted with lifting rings, they are

for lifting the motor on its own and must not be
used to lift the whole machine after the motor has been
H
fitted to it.
Note 1: When installing a suspended motor, it is essential
2.2.2 - Drip-proof motors to provide protection in case the fixing breaks.
Location ventilation Note 2: Never stand on the motor.
Our motors are cooled in accordance with method IC 01
(standard IEC 34-6), ie. «machine cooled by means of the
ambient fluid (air) circulating inside the machine». 2.3 - Coupling
A fan at the non-drive end cools the motor. Air is sucked in at Preparation
the front of the motor and blown along the fan cover to ensure Turn the motor by hand before coupling to detect any possible
thermal equilibrium of the motor whatever the direction of fault due to handling.
rotation. Remove any protection from the shaft extension.
air
inlet
ØH
max
H
The motor must be installed in an adequately ventilated area,

with clearance for the air intake and outlet of at least onequarter
of the frame size. Drain off any condensation water which may have formed
Obstruction (clogging) - even accidental - of the fan cover grille inside the motor by removing the plugs from the drain holes.
has an adverse effect on motor operation.
In the case of vertical operation with the shaft extension facing Rotor locking device
down, it is advisable to fit the motor with a drip cover to prevent For made-to-order motors with roller bearings, remove the
penetration by any foreign bodies. rotor locking device.
It is also necessary to check that the hot air is not being In exceptional circumstances when the motor has to be moved
recycled. If it is, pipes must be provided for the intake of cold after the coupling device has been fitted, the rotor must be re-
air and the discharge of hot air, in order prevent abnormal immobilised.
motor temperature rise.
In this case, if the air is not circulated by an auxiliary fan, the
dimensions of the pipes must be such that the pressure losses
are negligible compared to those of the motor.

4850 en - 2018.11 / f
ASSEMBLY
Applied Applied
to shoulder of shaft to stop ring
Balancing
Rotating machines are balanced in accordance with standard If there is a second shaft extension, it must only be used for
ISO 8821: direct coupling and the same recommendations must be
- Half-key when the shaft extension is marked H followed.
- No key when the shaft extension is marked N.
- Full key when the shaft extension is marked F.
and any coupling element (pulley, coupling sleeve, slip-ring, The 2nd shaft extension may also be smaller than
etc) must therefore be balanced accordingly. the main shaft extension, and under no
Motor with 2 shaft extensions: circumstances can it deliver torques greater than half the
If the second shaft extension is not used, in order to rated torque.
comply with the balancing class, the key or half-key must
be fixed firmly in the keyway so that it is not thrown out The inertia flywheels device must not be mounted directly
during rotation (H or F balancing) and must be protected onto the shaft extension, but installed between end shield and
against direct contact. device using a coupling.
Precautions Mounting a face mounted motor
All measures must be taken to ensure protection against the Mounting face mounted motors IM B14 (IM 3601) and IM B34
risks which arise when there are rotating parts (coupling (IM 2101).
sleeve, pulley, belt etc). Max. screw insertion length when mounting face mounted
motors IM B34 and IM B14.
If a motor is started up without a coupling device

having been fitted, carefully immobilize the key in Max. insertion (mm)
its location. LSES 71 F75 M5 / F85 M6 13
LSES 80 F100 M6 11
Beware of backdriving when the motor is switched off. The LSES 90 F115 M8 11
appropriate precautions must be taken: LSES 100 F130 M8 11
- For pumps, a non-return valve must be installed. LSES 112 F130 M8 11
- For mechanical devices, install a backstop or a holding brake. LSES 132 F215 M12 11
- etc.. LSES 160 F215 M12 15
Tolerances and adjustments
Direct connection onto the machine
The standard tolerances are applicable to the mechanical
When the mobile device (pump or fan turbine) is mounted
characteristics given in our catalogues. They comply fully with the
directly on the motor shaft extension, check that this device is
requirements of IEC standard 72-1.
perfectly balanced and that the radial force and the axial thrust
- Users must adhere strictly to the instructions provided by the
are within the limits indicated in the catalogue for the bearing
transmission device supplier.
withstand.
- Avoid impacts which could damage the bearings.
Use a spanner and the tapped hole of the shaft end with a special Direct connection using a flexible coupling
lubricant (e.g. molykote grease) to make it easier to fit the coupling. Selection of the coupling sleeve should take account of the
rated torque to be transmitted and the safety factor dependent
on the starting conditions for the electric motor.
The machines must be carefully aligned, so that any lack of
concentricity and parallelism in the two coupling halves is
compatible with the recommendations of the coupling sleeve
manufacturer.
Both parts of the coupling should be provisionally assembled
to make it easier to alter their relative position.
Adjust the parallel plane of both shafts using a gauge.
The hub of the transmission device must be: Measure the distance between the two coupling surfaces at
- Fully in contact with the shoulder of the shaft or, if this is missing, one point on the circumference. Rotate them 90°, 180° and
against the metal stop ring which forms a labyrinth seal and thus 270° in relation to this initial position, and measure each time.
locks the bearing in place (do not crush the seal). The difference between the two extremes of the value «x»
- Longer than the shaft extension (2 to 3 mm) so that it can be must not exceed 0.05 mm for standard couplings.
tightened using a screw and washer. If it is not, a spacer ring
must be inserted without cutting the key (if this ring is large, it
must be balanced).

4850 en - 2018.11 / f
ASSEMBLY
To perfect this adjustment and at the same time check the

concentricity of the two shafts, fit 2 gauges as shown in the
diagram and slowly turn both shafts. Protect all rotating devices before power-up.
The deviations registered by either shaft will indicate the need
for either an axial or radial adjustment if the deviation exceeds
0.05mm. Adjusting the tension of the belts
Direct connection using a rigid coupling The tension of the belts must be adjusted very carefully in
Both shafts must be aligned so as to adhere to the tolerances accordance with the recommendations of the belt supplier and
of the coupling sleeve manufacturer. the calculations made when the product was specified.
Maintain the minimum distance between the two shaft Reminder:
extensions to allow for expansion of the motor shaft and the - Tension too great = unnecessary force on the end shields
load shaft. which could lead to premature wear of the bearing unit (end
shield-bearings) and eventually break the shaft.
- Too little tension = vibration (wearing of the bearing unit).
Ø (mm) A (mm)
min. Fixed distance between centers:
A
9 to 55 1 Place a belt tensioning pulley on the slack side of the belts:
Ø
60 1.5 - Smooth pulley on the outside of the belt

65 1.5 - Grooved pulley on the inside of the belts when using V-belts.
75 2 Adjustable distance between centers:
80 2 The motor is usually mounted on slide rails, which enables
optimum adjustment of the pulley alignment and the belt
Transmission via belt pulleys tension.
The user can choose the diameter of the pulleys. Place the slide rails on a perfectly horizontal baseplate.
Cast iron pulleys with a diameter greater than 315 are not The lengthways position of the slide rails is determined by the
recommended for rotation speeds of 3000 min-1. length of the belt, and the crossways position by the pulley of
Flat belts cannot be used for rotation speeds of 3000 min-1 or the machine being driven.
more. Mount the slide rails firmly with the tension screws in the
direction shown in the diagram (the slide rail screw on the belt
Positioning the belts side between the motor and the machine being driven).
So that the belts can be correctly positioned, allow for Fix the slide rails onto the baseplate and adjust the belt tension
possible adjustment of approximately 3% with respect to the as before.
calculated distance E.
Force must never be used when fitting the belts.
For notched belts, position the notches in the pulley grooves
E
Tension screw
Tension screw
Aligning the pulleys

Check that the motor shaft is completely parallel with that of the
receiving pulley.

4850 en - 2018.11 / f
ASSEMBLY
Optional: Standard slide rails (conforming to standard NFC 51-105)

These steel slide rails are supplied with tension screws and the 4 nuts and bolts for fixing the motor on the slide rails, but the fixing
bolts for the slide rails are not supplied.
ØJ
H
A
K
L
E
Motor Type Dimensions Weight per pair

frame size of slide rail A E H K L X Y Z ØJ of slide rails (kg)
90 G 90/8 PM 355 395 40 2.5 50 324 264 294 13 3
100, 112 and 132 G 132/10 PM 420 530 49.5 7 60 442 368 405 15 6
160 and 180 G 180/12 PM 630 686 60.5 7 75 575 475 525 19 11
200 and 225 G 225/16 PF 800 864 75 28.5 90 - 623 698 24 16
250 and 280 G 280/20 PF 1000 1072 100 35 112 - 764 864 30 36
315 and 355 G 355/24 PF 1250 1330 125 36 130 - 946 1064 30 60
2.4 - Electrical guidelines The five essential modes are:

- D.O.L. starting
2.4.1 - Limiting problems caused by motor - Star/delta starting
- Soft starting with autotransformer
starting
- Soft starting with resistors
In order to protect the installation, any significant temperature - Electronic starting
rise in the cabling conduits must be prevented, while ensuring The «electronic» starting modes control the voltage at the
that the protection devices do not interrupt starting. motor terminals during the entire starting phase and enable
Operating problems in other equipment connected to the same very soft, jolt-free starting.
supply are due to the voltage drop caused by the current
demand on starting - many times greater than the current
absorbed by the motor at full load (approximately 7). 2.4.2 - LEROY-SOMER «Digistart» electronic
See the LEROY-SOMER induction motors technical starter
catalogue). This is a multi-function electronic system with a microcontroller,
Even though the mains supplies increasingly allow D.O.L. which is used with all 3-phase cage induction motors.
starting, the current inrush must be reduced for certain It provides soft starting of the motor with:
installations. - Reduction of the starting current
Jolt-free operation and soft starting ensure greater ease of use - Gradual, jolt-free acceleration, achieved by controlling the
and an increased lifespan for the machines being driven. current absorbed by the motor.
The two essential parameters for starting cage induction After starting, the DIGISTART performs additional motor
motors are: control functions in its other operating phases: steady state
- starting torque and deceleration.
- starting current - 18 to 1600 A models
The starting torque and the resistive torque determine the - Supply: 220 to 700 V - 50/60 Hz
starting time. DIGISTART is economical to install, as a fused switch is the
Depending on the load being driven, it may be necessary to only additional device needed.
adapt the torque and the current to the machine starting time
and to the possibilities of the mains power supply.

4850 en - 2018.11 / f
ASSEMBLY
2.4.3 - Other control systems 2.4.4 - Permissible starting times and locked
Frequency inverters, flux vector control, etc. Special rotor times
precautions need to be taken when standard induction motors The starting times must remain within the limits stated below
are being used for variable speed control, powered by a on condition that the number of starts per hour is 6 or less.
frequency inverter or voltage controller: Three successive cold starts and two consecutive warm starts
are allowed.
The reference voltage (drive output or motor
25
input) is 400V at 50 Hz: The drive must deliver a
constant voltage/frequency signal to the motor in the
50 Hz operating range. Beyond the 25/50 Hz range, 20
ensure that the fan and bearing unit are suitable.
Time (s)
15
During prolonged operation at low speed, cooling efficiency is
greatly diminished. It is therefore advisable to install a forced
ventilation unit that will produce a constant flow of air 10
independently of the motor speed.
In prolonged operation at high speed, the fan may make
excessive noise. It is again advisable to install a forced 5
5 6 7 8 9 10
Id/In
ventilation system.
Cold start Hot start
Effect of
cooling Permissible motor starting time in relation to the ratio ID / IN.
Forced ventilation Natural cooling Forced ventilation

(temperature rise) for N > 3600 min-1 2.4.5 - Earthing (see section 2.5.5)
1
2.4.6 - Power factor compensation capacitors
2/3 P/PN = f (N/NS)
Before any work is carried out on the motor or in

1/3 the cabinet, check that the capacitors are
isolated and/or discharged (read the voltage at the
N / Ns terminals).
0 1/3 2/3 1 Operating speed/
Synchronous speed
2.4.7 - Motor protection devices
If the frequency exceeds 50 Hz:
2.4.7.1 - On-line protection
a - Carefully check that all the components on a particular
transmission are properly aligned. Adjusting the thermal protection
b - The voltage remains constant above 50 Hz. It should be adjusted to the value of the current read on the
c - The power supplied by the motor up to 60 Hz remains motor nameplate for the connected mains voltage and
constant (make sure that the power absorbed by the load does frequency.
not vary differently in this frequency range). Thermal magnetic protection
d - Check that the application speed does not exceed the The motors must be protected by a thermal magnetic device
synchronous speed values: located between the isolating switch and the motor. These
- 2P --> 3600 min-1 motors protection devices provide total protection of the motor against
- 4P --> 1800 min-1 motors non-transient overloads.
- 6P --> 1200 min-1 motors This device can be accompanied by fused circuit-breakers.
e - For all other frequency and/or voltage limits, additional Built-in direct thermal protection
precautions must be taken for derating, bearings, ventilation, For low rated currents, bimetallic strip-type protection may be
noise, etc: please consult Leroy-Somer. used. The line current passes through the strip, which shuts
Check that the vibration level of the assembled machine down or restores the supply circuit as necessary. The design
complies with standard ISO 10816-3. of this type of protection allows for manual or automatic reset.
2.4.7.2 - Built-in indirect thermal protection
The user is responsible for protecting the motor and drive The motors can be equipped with optional heat sensors.
equipment from hazardous currents and overvoltages in the These sensors can be used to monitor temperature changes
winding. These instructions cannot guarantee efficiency in all at “hot spots”:
cases. - overload detection
- cooling check
- Monitoring strategic points for maintenance of the installation

4850 en - 2018.11 / f
ASSEMBLY
It must be emphasized that these sensors cannot be used to carry out direct adjustments to the motor operating cycles.
Operating Operating Breaking Mounting

Type Protection provided
principle curve capacity (A) Number required*
bimetallic strip, I
indirectly heated Mounted on control
operates on opening (0) general surveillance
Normally closed 1.6 at 250 V circuit
for non-transient
thermostat with cos j 0.6 overloads
T 2 or 3 in series
PTO
O NRT
bimetallic strip,
I
indirectly heated, Mounted on control
contact on closing (F) 1.6 at 250 V general surveillance circuit
Normally open for non-transient
thermostat with cos j 0.6 overloads
PTF T 2 or 3 in parallel
F NRT
Variable non-linear
resistor, indirectly R
Mounted with associated
heated general surveillance
Positive temperature relay on control circuit
0 for transient
coefficient thermistor
overloads
PTC T 3 in series
NRT
Thermocouples V Mounted on control

continuous
T (T<150°C) panels with associated
surveillance reading device
Constantan copper Peltier effect 0
at hot spots (or recording device)
K (T<1000°C)
T at regular intervals
Copper Copper-Nickel 1 per hot spot
R Mounted on control
Variable linear high accuracy panels with associated
Platinum resistance
continuous reading device
thermometer resistance, 0
surveillance (or recording device)
PT 100 indirectly heated T at key hot spots
1 per hot spot
- NRT: nominal running temperature.

- The NRTs are chosen according to the position of the sensor in the motor and the temperature rise class.
* The number of devices affects the protection of the windings.
Alarm and early warning
All protective equipment can be backed up by another type of Protection against condensation: space heaters
protection (with different NRTs): The first device will then act as Identification: 1 red label
an early warning (light or sound signals given without shutting
down the power circuits), and the second device will be the A glass fibre flexible resistor is fixed on 1 or 2 coil end turns.
alarm (shutting down the power circuits). This resistor heats the machines when stopped and thus
prevents condensation inside the machines.
Power supply: 230V single-phase unless otherwise specified
Warning: Depending on the type of protection, by the customer.
the motor may remain powered-up. Ensure that If the drain plugs at the bottom of the motor have not been
the mains supply is disconnected before any work is
removed at the time of installation, they must be opened
carried out in the terminal box or in the cabinet.
approximately every 6 months.
Warning: Check that the space heaters are

powered down before any work is carried out in
the terminal box or in the cabinet.

4850 en - 2018.11 / f
ASSEMBLY
2.5 - Mains connection If the non-standard position of the cable gland has not been
correctly specified on the order, or is no longer suitable, the
2.5.1 - Terminal box symmetrical construction of the terminal box enables it to be
turned in any of the 4 directions except for position (2) on
Placed as standard on the top of the motor near the drive end,
flange-mounted motors (B5).
for forms IM B3, B5, B14, the terminal box has IP 55 protection.
A cable gland must never open upwards.
Warning: The position of the terminal box cannot be easily
Check that the incoming cables have bends of such a radius as
modified, even with flanged motors, as the condensation drain
to prevent water from running into the cable gland.
holes must be at the bottom.
Cable gland
The standard position of the cable gland (1) is on the right,
seen from the drive end.
A Standard
position
3
2 4
1
Standard
position
NB: motors are fitted with plugs or a support plate as standard.
Tightening capacity of cable glands
Ø min. - Ø max. (mm) cable

Adapt the cable gland and Type
its reducer if present to the of cable gland Polyamide cable Brass cable gland
gland
Ø maxi
diameter of the cable being used.

Ø mini
In order to preserve the motor’s ISO M16 5 - 10 5.5 - 9.5

original IP55 protection, it is ISO M20 9.5 - 15 8.5 - 13
essential to tighten the cable gland seal correctly (so
ISO M25 13 - 19 12 - 17
that it cannot be unscrewed by hand).
ISO M32 15 - 25 15 - 22
When there are several cable glands and some are not
being used, ensure that they are always covered and ISO M40 21 - 32 19.5 - 28
tighten them so that they also cannot be unscrewed by ISO M50 26 - 38 25.5 - 36
hand.
ISO M63 31 - 34 33 - 46

4850 en - 2018.11 / f
ASSEMBLY
2.5.2 - Cross-section of the power supply cables If the most important criterion is the starting torque (or starting
time), the voltage drop should be limited to 3% maximum (the
The higher the current, the greater the voltage drop in the
equivalent of a loss of torque of around 6 to 8%).
cables (standard NFC 15.100 or end user’s national standard).
The chart below can be used to select the conductors according
The voltage drop should therefore be calculated for the
to the length of the supply cables and the starting current, in
starting current to see if this is suitable for the application. order to limit the voltage drop to 3% maximum.
Length in m Maximum voltage drop 3 % (3-phase circuits - copper cable)

1000
900
800
700
600
500
400
1 1.5 2.5 4 6 10 16 25 35 50 75 90 Conductor cross-section
300
200
100
90
80
70
60
50
40
30
20
10
1 2 3 4 5 6 7 8 9 10 2 3 4 5 6 7 8 9 100 2 3 4 5 6 7 8 9 1000 2 3 4 5
Current in amps
This table does not allow the installer to dispense with checking the protective systems. Starting current
For motors with flying leads, the power supply cable must not be used for handling.
2.5.3 - Connection of the motor-drive unit

When controlling an induction motor by means of a variable
speed drive, certain rules must be adhered to in order to
guarantee correct system performance.
For variable speed applications, follow the recommendations
outlined in the good practice guide for Motor and drive
packages ref. 5626.

4850 en - 2018.11 / f
ASSEMBLY
2.5.4 - Terminal block wiring diagram 2.5.7 - Connecting the power supply cables to
All motors are supplied with a wiring diagram in the terminal the terminal block
box*. The cables must be fitted with connectors suitable for the cable
The connector links required for coupling can be found inside cross-section and the terminal diameter.
the terminal box. They must be crimped in accordance with the connector
Single-speed motors are fitted with a block of 6 terminals supplier’s instructions.
complying with standard NFC 51 120, with the terminal Connection must be carried out with connector resting on
markings complying with IEC 34 - 8 (or NFC 51 118). connector (see the diagrams below):
Particular attention must be paid to the

information on the nameplate in order to choose
the correct type of connection for the supply voltage.
2.5.5 - Direction of rotation

When the motor is powered by U1, V1, W1 or 1U, 1V, 1W from
a direct mains supply L1, L2, L3, it turns clockwise when seen
from the drive end.
If 2 phases of the power supply are changed over, the motor
will run in an anti-clockwise direction (make sure the motor has
been designed to run in both directions of rotation).
Warning: motor with backstop: starting in the wrong direction
destroys the backstop (see arrow on motor housing). Tightening torque (N.m) on the terminal block nuts
If the motor is fitted with accessories (thermal protection or
Terminal M4 M5 M6 M8 M10 M12 M14 M16
space heater), these should be connected on screw dominos
or terminal blocks with labelled wires (see section 2.4). Steel 1 2.5 4 10 20 35 50 65
Brass 1 2 3 6 12 20 - 50
Temperature probe
If using cables without connectors, attach some calipers.

If any nuts on the brass terminal block are lost, they must be
replaced by brass nuts, not steel ones.
When closing the box, ensure that the seal is correctly
positioned.
As a general rule, check that no nut, washer or

other foreign body has fallen into or come into
contact with the winding.
2.5.6 - Earth terminal

This is situated inside the terminal box; in some cases, the
earth terminal may be situated on one of the feet or on one of
the cooling fins (round motors).
It is indicated by the symbol:
It is compulsory to earth the motor. Earthing

must be performed in accordance with current
regulations (protection of workers).
* If required, this diagram should be obtained from the supplier,

specifying the motor type and number (shown on the motor
nameplate).

4850 en - 2018.11 / f
ROUTINE MAINTENANCE
3 - ROUTINE MAINTENANCE Condensation drain holes, located at the bottom of the motors
(bearing in mind their operating position) are sealed with plugs
Checks after start-up which must be removed and then replaced every six months (if
After approximately 50 hours’ operation, check that the screws they were not replaced, the motor degree of protection would
fixing the motor and the coupling device are still tight. no longer be maintained). Clean the orifices and plugs before
In the case of chain or belt transmission, check that the tension reassembling them.
is correctly adjusted. Note: In conditions of high humidity and significant temperature
variations, a shorter period is recommended.
Cleaning
As long as it poses no risk to the motor protection, the
To ensure the motor operates correctly, remove any dust or
condensation drain plugs can be removed.
foreign bodies which might clog the cover grille and the housing
fins.
Precaution: before carrying out any cleaning operation check 3.1 - Greasing
that the motor is completely sealed (terminal box, drain holes,
etc). 3.1.1 - Type of grease
Dry cleaning (vacuuming or compressed air) is always When the bearings are not greased for life, the type of grease
preferable to wet cleaning. is indicated on the nameplate.
As standard this grease is Polyrex EM103 and we recommend
that it is used for subsequent lubrication.
Always clean at reduced pressure from the center
of the motor towards the extremities to avoid Avoid mixing greases.
introducing dust and particles under the seals. 3.1.2 - Permanently greased bearings
For LS/LSES and FLS/FLSES ≤ 225 motors, the bearings
Draining off condensation water defined offer long grease life and therefore lubrication for the
Temperature variations cause condensation to form inside lifetime of the machines. The grease life according to speed of
the motor, which must be removed before it adversely affects
motor operation. rotation and ambient temperature is shown on the chart below.
PERMANENTLY GREASED BEARINGS

Under normal operating conditions, the service life (L10h) in hours of the lubricant is indicated in the table below for ambient
temperatures less than 55°C.
Types of permanently Grease life according to speed of rotation

No. of greased bearing 3000 rpm 1500 rpm 1000 rpm
Series Type poles N.D.E. D.E. 25°C 40°C 55°C 25°C 40°C 55°C 25°C 40°C 55°C
80 L 2 6203 CN 6204 C3 ≥40000 ≥40000 25000 - - - - - -
80LG 2;4 - - -
6204 C3 6205 C3 ≥40000 ≥40000 24000 ≥40000 ≥40000 31000
90 SL/L 2;4;6 ≥40000 ≥40000 34000
90 LU 4 6205 C3 6205 C3 - - - ≥40000 ≥40000 30000 - - -
100 L 2;4;6 ≥40000 ≥40000 22000 ≥40000 ≥40000 33000
6205 C3 6206 C3 ≥40000 ≥40000 30000
100 LR 4 - - - - - -
112 M 2 - - -
6205 C3 6206 C3 ≥40000 ≥40000 22000 - - -
112 MG 2;6 ≥40000 ≥40000 33000
112 MU 4 6206 C3 6206 C3 - - - ≥40000 ≥40000 30000 - - -
132 S 2;6 - - - ≥40000 ≥40000 30000
6206 C3 6208 C3 ≥40000 ≥40000 19000
132 SU 2;4 ≥40000 ≥40000 25000 - - -
132 SM/M 2;4;6 6207 C3 6308 C3 ≥40000 ≥40000 19000 ≥40000 ≥40000 25000 ≥40000 ≥40000 30000
132 MU 4;6 6307 C3 6308 C3 - - - ≥40000 ≥40000 25000 ≥40000 ≥40000 30000
160 MR 2;4 6308 C3 6309 C3 ≥40000 35000 15000 ≥40000 ≥40000 24000 - - -
160 MP 2;4 6208 C3 6309 C3 ≥40000 35000 18000 ≥40000 ≥40000 24000 - - -
160 M/MU 6 - - - - - -
LS/LSES 6210 C3 6309 C3 ≥40000 ≥40000 27000
160 L 2;4;6 ≥40000 30000 15000 ≥40000 ≥40000 23000
160 LUR 4;6 - - - ≥40000 ≥40000 27000
6210 C3 6310 C3 ≥40000 ≥40000 23000
180 MT 2;4 ≥40000 30000 15000 - - -
180 M 4 ≥40000 ≥40000 24900 - - -
6212 C3 6310 C3 - - -
180 L 6 - - - ≥40000 ≥40000 28000
180 LR 4 6210 C3 6310 C3 - - - ≥40000 ≥40000 23000 - - -
180 LUR 4;6 6312 C3 6310 C3 - - - ≥40000 ≥40000 22000 ≥40000 ≥40000 27000
200 L 2;6 6214 C3 6312 C3 ≥40000 25000 12500 - - - ≥40000 ≥40000 27000
200 LR 2;4;6 ≥40000 25000 12500
6312 C3 6312 C3 ≥40000 ≥40000 22000 ≥40000 ≥40000 27000
200 LU 4;6 - - -
225 ST 4 - - - ≥40000 ≥40000 21000
6214 C3 6313 C3 - - -
225 MT 2 ≥40000 22000 11000 - - -
225 SR 4 - - - - - -
6312 C3 6313 C3 ≥40000 ≥40000 21000
225 MR 2;4;6 ≥40000 22000 11000 ≥40000 ≥40000 26000
225 SG 4 - - -
6216 C3 6314 C3 - - - ≥40000 ≥40000 20000
225 MG 4;6 ≥40000 ≥40000 25000
Note: on request, all motors can be fitted with grease nipples except the 132 S/SU.

4850 en - 2018.11 / f
ROUTINE MAINTENANCE
Types of permanently Grease life according to speed of rotation

greased bearing 3000 rpm 1500 rpm 1000 rpm
No. of
Series Type poles N.D.E. D.E. 25°C 40°C 55°C 25°C 40°C 55°C 25°C 40°C 55°C
80 L 2 6203 CN 6204 C3 ≥40000 ≥40000 25000 - - - - - -
80 LG 4 - - - - - -
6204 C3 6205 C3 ≥40000 ≥40000 31000
90 SL/L 2;4;6 ≥40000 ≥40000 24000 ≥40000 ≥40000 34000
90 LU 2;6 6205 C3 6205 C3 ≥40000 ≥40000 24000 - - - ≥40000 ≥40000 34000
100 L 2;4 ≥40000 ≥40000 22000 - - -
≥40000 ≥40000 30000
100 LG 4;6 6205 C3 6206 C3 - - -
≥40000 ≥40000 33000
112 MG 2;6 ≥40000 ≥40000 22000 - - -
112 MU 4 6206 C3 6206 C3 - - - ≥40000 ≥40000 30000 - - -
132 SM/M 2;4;6 6207 C3 6308 C3 ≥40000 ≥40000 19000 ≥40000 ≥40000 25000 ≥40000 ≥40000 30000
132 MU 2;4 6307 C3 6308 C3 ≥40000 ≥40000 19000 ≥40000 ≥40000 25000 - - -
132 MR 4;6 6308 C3 6308 C3 - - - ≥40000 ≥40000 25000 ≥40000 ≥40000 30000
160 M 2;4;6 ≥ 40000 37800 18900 ≥ 40000 ≥ 40000 36900
FLS/FLSES 6210 C3 6309 C3 ≥ 40000 ≥ 40000 20050
160 MU 6 - - - - - -
160 LUR 2;4;6 6210 C3 6310 C3 ≥ 40000 24500 12250 ≥ 40000 36400 18200 ≥ 40000 ≥ 40000 22450
180 M 2 6212 C3 6310 C3 34000 17000 8500 - - - - - -
180 MT 4 6210 C3 6310 C3 - - - ≥ 40000 35500 17750 - - -
180 MUR 2 6312 C3 6310 C3 ≥ 40000 22800 11400 - - - - - -
180 L 4;6 6212 C3 6310 C3 - - - ≥ 40000 39500 19750 ≥ 40000 ≥ 40000 29050
180 LUR 4;6 6312 C3 6310 C3 - - - ≥ 40000 ≥ 40000 22900 ≥ 40000 ≥ 40000 29900
200 LU 2;4;6 6312 C3 6312 C3 28600 14300 7150 ≥ 40000 25400 12700 ≥ 40000 33200 16600
225 S 4 6314 C3 6314 C3 - - - ≥ 40000 23700 11850 - - -
225 SR 4 6312 C3 6313 C3 - - - ≥ 40000 ≥ 40000 21500 - - -
225 M 4;6 6314 C3 6314 C3 - - - ≥ 40000 23700 11850 ≥ 40000 25600 12800
225 MR 2 6312 C3 6313 C3 ≥ 40000 22800 11400 - - - - - -
Note: on request, all motors can be fitted with grease nipples.

4850 en - 2018.11 / f
ROUTINE MAINTENANCE
3.1.3 - Bearings with grease nipples

The bearings are lubricated in the factory Even in the event of prolonged storage or
The end shields are fitted with bearings lubricated by grease downtime, the interval between 2 greasing
nipples such as Tecalemit-Hydraulic M8 x 125. operations should never exceed 2 years.
The frequency of lubrication and the quantity and

quality of grease are given on the nameplates and
these should be referred to in order to ensure correct
bearing lubrication.
Type of bearing for Greasing intervals in hours

Quantity
bearings with grease nipples of grease 3000 rpm 1500 rpm 1000 rpm
No. of
Series Type poles N.D.E. D.E. g 25°C 40°C 55°C 25°C 40°C 55°C 25°C 40°C 55°C
160 M/MU*
2;4;6 6210 C3 6309 C3 13 22200 11100 5550 32400 16200 8100 39800 19900 9950
160 L*
180 MR* 2 - - -
19600 9800 4900
180 MT* 2;4 6210 C3 6310 C3 15 - - -
30400 15200 7600
180 LR* 4 - - -
180 LUR* 4;6 6312 C3 6310 C3 20 - - - 26800 13400 6700 35000 17500 8750
180 M* 4 29200 14600 7300 - - -

6212 C3 6310 C3 15 - - -
180 L* 6 - - - 37200 18600 9300
200 LR* 2;4;6 15200 7600 3800

6312 C3 6312 C3 20 26800 13400 6700 35000 17500 8750
200 LU* 4;6 - - -
200 L* 2;6 6214 C3 6312 C3 20 14600 7300 3650 - - - 34600 17300 8650
225 ST* 4 - - - 25200 12600 6300

6214 C3 6313 C3 25 - - -
LS/LSES 225 MT* 2 10600 5300 2650 - - -
225 SR/MR* 2;4;6 6312 C3 6313 C3 25 13400 6700 3350 25200 12600 6300 33600 16800 8400
225 SG* 4 - - -
6216 C3 6314 C3 25 - - - 23600 11800 5900
225 MG* 4;6 32200 16100 8050
250 MZ 2 6312 C3 6313 C3 25 13400 6700 3350 - - - - - -
250 ME 4;6 - - - 16800 8400 16800 22800 11400 5700

6216 C3 6314 C3 25
280 SC/MC 2 11800 5900 2950 - - - - - -
280 SC 6 6216 C3 6316 C3 35 - - - - - - 32200 16100 8050
280 SD/MD 4;6 6218 C3 6316 C3 35 - - - 1900 3800 7600 29600 14800 7400
315 SN 2 6216 C3 6316 C3 35 5600 2800 1400 - - - - - -
315 MP 2 6317 C3 6317 C3 40 5200 2600 1300 - - - - - -
315 SP 4 - - -
6317 C3 6320 C3 50 - - - 14000 7000 14000
315 MP/MR 4;6 21200 10600 5300
* bearing with grease nipple available to order

4850 en - 2018.11 / f
ROUTINE MAINTENANCE
Greasing intervals in hours

Type of bearing for Quantity
bearings with grease nipples of grease 3000 rpm 1500 rpm 1000 rpm
No. of
Series Type poles N.D.E. D.E. g 25°C 40°C 55°C 25°C 40°C 55°C 25°C 40°C 55°C
160 M* 2;4;6 22200 11100 5550 32400 16200 8100 39800 19900 9950
6210 C3 6309 C3 13
160 MU 6 - - - - - - 23400 11700 5850
160 LUR* 2;4;6 6210 C3 6310 C3 15 19600 9800 4900 30400 15200 7600 38200 19100 6600
180 M* 2 6212 C3 6310 C3 15 18000 9000 4500 - - - - - -
180 MT* 4 6210 C3 6310 C3 15 - - - 30400 15200 7600 - - -
180 MUR* 2 6312 C3 6310 C3 15 10600 5300 2650 - - - - - -
180 L* 4;6 6212 C3 6310 C3 20 - - - 29200 14600 7300 37200 18600 9300
180 LUR* 4;6 6312 C3 6310 C3 20 - - - 26800 13400 6700 35000 17500 8750
200 LU* 2;4;6 6312 C3 6312 C3 20 15200 7600 3800 26800 13400 6700 35000 17500 8750
225 S* 4 6314 C3 6314 C3 25 - - - 23600 11800 5900 - - -
225 SR* 4 6312 C3 6313 C3 25 - - - 25200 12600 6300 - - -
FLS/FLSES 225 M* 4;6 6314 C3 6314 C3 25 - - - 23600 11800 5900 32200 16100 8050
225 MR* 2 6312 C3 6313 C3 25 13400 6700 3350 - - - - - -
250 M 2;6 10400 5200 2600 - - - 32200 16100 8050
6314 C3 6314 C3 25
250 MR 4 - - - 17800 8900 4450 - - -
280 S/M 2;4;6 6314 C3 6316 C3 35 7200 3600 1800 21000 13230 6615 29000 29000 18270
315 S/M/L 2 6316 C3 6218 C3 35 7400 5880 2920 - - - - - -
315 S/M/L 4;6 6316 C3 6320 C3 50 - - - 15600 12400 6160 25000 25000 12500
355 L 2 6316 C3 6218 C3 35 7400 3700 1850 - - - - - -
355 L 4;6 6316 C3 6322 C3 60 - - - 13200 8316 4160 22000 13860 6930
355 LK 4;6 6324 C3 6324 C3 72 - - - 7500 3700 2800 20000 20000 10000
400 L/LV 4;6 6324 C3 6324 C3 72 - - - 7500 3700 2800 20000 20000 10000
400 LK/ 450 L 4;6 6328 C3 6328 C3 93 - - - 4600 2300 1100 10000 6000 3000
Type of bearing for Greasing intervals in hours

Quantity
bearings with grease nipples of grease 3000 rpm 1500 rpm
No. of
Series Type poles N.D.E. D.E. g 25°C 40°C 55°C 25°C 40°C 55°C
225 MG
250 SF 2;4
6314 C3 6317 C3 40 8000 4000 2000 19600 9800 4900
250 MF
280 MD 2
280 SGU 4
280 MGU 4
- - - 15800 7900 3950
315 SUR 4
6316 C3 6320 C3 50
315 LUS 4
315 SU 2
9000 4500 2250 - - -
PLS/PLSES 315 MU 2
315 L 2 6316 C3 6316 C3 35 9000 4500 2250 - - -
315 LD 2 6316 C3 6219 C3 35 8000 4000 2000 - - -
2 6317 C3 6317 C3 35 6500 6500 4095 - - -
315 LG/MGU
4 6317 C3 6322 C3 55 - - - 13200 13200 8316
2 6317 C3 6317 C3 35 6500 6500 4095 - - -
315 VLG/VLGU
4 6317 C3 6322 C3 55 - - - 13200 13200 8316
2 6317 C3 6317 C3 35 6500 6500 4095 - - -
355 L
4 6324 C3 6324 C3 72 - - - 7500 3700 2800
400 L 4 6328 C3 6328 C3 93 - - - 4600 2300 1100

4850 en - 2018.11 / f
PREVENTIVE MAINTENANCE
3.2 - Bearing maintenance Bearings with grease nipples

Always begin by cleaning the waste grease channel
3.2.1 - Checking the bearings If using the type of grease stated on the nameplate, remove the
covers and clean the grease nipple heads.
As soon as you detect any of the following on the motor:
If a different grease from that on the nameplate is being used,
- Abnormal noise or vibration the motor must be dismantled and the bearings and accessories
- Abnormal temperature rise in the bearing even though it has cleaned with degreasing agent (carefully clean the grease inlet
been lubricated correctly, and outlet pipes) to remove the old grease before relubrication.
the condition of the bearings must be checked. To ensure correct lubrication, fill the inner free spaces of the
Damaged bearings must be replaced as soon as possible bearing retainers, flanges and grease pipes and 30% of the
to prevent worse damage to the motor and the equipment bearing free space.
being driven. Then rotate the motor shaft to distribute the grease.
If one bearing needs to be replaced, the other bearing must
also be replaced. Warning:
The seals should be changed routinely when the bearings Too much grease causes the bearing to overheat (statistics
are changed. show that more bearings are damaged through too much
The free bearing must allow the rotor shaft to expand (check its grease than too little grease).
identification during dismantling).
Important note:
The new grease should be recently manufactured, of equivalent
performance and should not contain any impurities (dust,
3.2.2 - Reconditioning the bearings
water, etc).
Bearings without grease nipples
Dismantle the motor (see section 6.1); remove the old grease
and clean the bearings and accessories with degreasing
agent.
Fill with new grease: the correct amount of new grease for the
bearing is 50% of the free space.
4 - PREVENTIVE MAINTENANCE M 01V M 02V

Please consult LEROY-SOMER who, in its continuous search
for ways to help customers, has evaluated numerous methods 3
of preventive maintenance.
The diagram and table below give the recommended 4
1
equipment to use and the ideal positions to take measurements 2
of all parameters which can affect the operation of the machine,
such as eccentricity, vibration, state of bearings, structural
problems, electrical problems, etc.
5 M 02A
M 01H M 02H
Measurement points
Detector Measurement
M 01V M 01H M 02V M 02H M 02A Shaft E01 E02 E03
Accelerometer For measuring vibrations

• • • • •
Photo-electric cell For measuring speed and phase
(balancing) •
Clamp ammeter For measuring current
(D.C. and 3-phase) • • •
Voltage probe For measuring voltage
• • •
Infra-red probe For measuring temperature
• •

4850 en - 2018.11 / f
TROUBLESHOOTING GUIDE
5 - TROUBLESHOOTING GUIDE
Incident Possible cause Remedy
Abnormal noise Originating in motor or machine being driven? Uncouple the motor from the equipment being driven
and test the motor on its own
Noisy motor The cause is mechanical if the noise persists after
switching off the power supply, with the drive set to
«freewheel» mode
- vibration - check that the key conforms to the type of
balancing (see section 2.3)
- damaged bearings - change the bearings
- mechanical friction: ventilation, coupling - check and replace the defective part
The cause is electrical if the noise stops after - check the power supply at the motor terminals
switching off the power supply - check the drive settings
- normal voltage and 3 phases balanced - check the connection of the terminal block and
the tightening of the terminals
- abnormal voltage - check the power supply line
- phase imbalance - check the winding resistance
Other possible causes: - refer to the drive manual

- incorrect settings
- drive malfunction
Motor heats abnormally - faulty ventilation - check the environment

- clean the fan cover and the cooling fins
- check that the fan is correctly mounted on the shaft
- faulty supply voltage - check
- terminal connection fault - check
- overload - check the current consumption in relation to that

indicated on the motor nameplate
- partial short-circuit - check the electrical continuity of the windings and/or

the installation
- phase imbalance - check the winding resistance
Other possible causes: - refer to the drive manual

- incorrect settings
- drive malfunction
Motor does not start at no load When switched off:

- mechanical locking - check that rotation of the shaft is locked
- broken power supply line - check the fuses, electrical protection, starting
device
- position feedback (drive message) - check the drive wiring and settings, operation of the
position sensor
- thermal protection - check

on load When switched off:
- phase imbalance - check the direction of rotation (phase order)
- check the resistance and continuity of the windings
- check the electrical protection
- drive - check the settings and sizing (max. current that can
be delivered by the drive)
- position feedback (drive message) - check the drive wiring and settings, operation of the
position sensor
- thermal protection - check

4850 en - 2018.11 / f
CORRECTIVE MAINTENANCE: GENERAL
6 - CORRECTIVE MAINTENANCE:
- Hot state: Heat the bearing to between 80 and 100 °C: in a
GENERAL dryer, an oven or on a heating plate. (A blowtorch or an oil bath
must never be used).
After dismantling and reassembling a bearing, all the spaces
First switch off and lock the power supply between the seals and labyrinth seals must be filled with
grease in order to prevent the entry of dust and the rusting of
- Open the terminal box, mark the wires and their positions machined parts.
- Disconnect the power supply wires See detailed instructions for the relevant motor ranges in the
following pages.
- Uncouple the motor from the equipment being driven
Always use an extractor to remove any devices mounted on
the shaft end of the motor.
6.4 - Reassembling the motor
Be careful to replace the stator in its original position, that
the stack of laminations is centered correctly (generally with
the terminal box facing forward) and the water drain holes are
positioned correctly if they are on the housing.
Tightening the tie rods/screws
These must be tightened diagonally, to the torque indicated
(see below).
1 4
6.1 - Dismantling the motor 3 2

Refer to the detailed instructions for the relevant motor range
(see following pages).
It is advisable to mark the shields in relation to the stator and Tie rods/screws tightening torque
the direction in which the rotor fan is mounted. Tightening torque
Type Rod/screw Ø
N. m ± 5%
6.2 - Checks before reassembly 56 M4 2.5
63 M4 2.5
Stator: 71 M4 2.5
- Remove all dust from the stator: 80 M5 4
If the winding needs to be cleaned, a suitable liquid must be 90 M5 4
used: dielectric and inert on the insulating components and the 100 M5 or M6 4
external finish. 112 M5 or M6 4
- Check the insulation (see section 2.1) and if necessary, dry it 132 M7 10
in an oven. 160 M8 18
- Clean the spigots thoroughly, and remove all traces of knocks 180 MT/LR/LUR M8 18
on the mating surfaces if necessary. 180 L M10 25
Rotor: 200 M10 25
- Clean and check the bearing running surfaces. If they are 225 ST/MR/SR M10 25
damaged, renew the running surfaces or change the rotor. 225 MK M12 44
- Check the condition of the threads, keys and their housings. 250 M12 44
End shields: 280 M12 44
- Clean off any traces of dirt (old grease, accumulated dust, 315 M12 44
etc). 315 LK / 355 M16 100
- Clean the bearing housings and the spigot. 355 LK / 400 M16 100
- If necessary, apply anti-flash varnish to the insides of the end 450 M16 100
shields.
- Carefully clean the bearing retainers and the grease valves (if
these are fitted on the motor).
6.5 - Reassembling the terminal box
Reconnect all the power supply wires in accordance with the
6.3 - Mounting the bearings on the shaft diagram or markings made before dismantling.
To ensure the box is properly sealed: check that the cable
This operation is extremely important, as the slightest glands on the box and the cable(s) have been retightened, and
indentation of a ball on the bearing tracks would cause noise ensure that the seal has been correctly positioned before
and vibration. closing. For terminal boxes equipped with a horn (part no. 89
Lightly lubricate the running surfaces of the shaft. on the exploded views) or/and a cable gland support plate,
There are a number of ways of mounting the bearings correctly: ensure that the seal has been correctly positioned before
- Cold state: The bearings must be mounted without any closing. Check that the terminal box components are tightened
impact, using a spanner (do not use a hammer). The force correctly.
applied must not be transferred to the bearing track. You should Note: It is advisable to test the motor at no load
therefore use the internal cage for support (taking care not to - If necessary, repaint the motor.
press on the seal shield for sealed bearings). - Mount the transmission device on the motor shaft extension
and reinstall the motor on the machine to be driven.

4850 en - 2018.11 / f
POSITION OF LIFTING RINGS
7 - POSITION OF LIFTING RINGS

Horizontal position
Type
A e min h min Øt
Position of lifting rings for lifting the motor only
(not connected to the machine). LSES 100 L/LR/LG 165 165 150 9
LSES 112 M/MR 165 165 150 9
LSES 112 MG/MU - - - 9
Labour regulations stipulate that all loads over 25 kg must be
LSES 132 S/SU 180 180 150 9
fitted with lifting devices to facilitate handling.
LSES 132 M/MU 200 180 150 14
The positions of the lifting rings and the minimum dimensions
LSES 160 MP/MR/LR 200 180 110 14
of the loading bars are given below in order to help with
LSES 160 M/MU/L/LUR 200 260 150 14
preparation for handling the motors. If these precautions are
LSES 180 M/MUR/L/LUR 200 260 150 14
not followed, there is a risk of warping or crushing some
LSES 200 L/LR 270 260 150 14
equipment such as the terminal box, protective cover or drip LSES 200 LU 270 260 150 14
cover. LSES 225 SR/MR 270 260 150 14
LSES 225 S/SG/M/MG 360 380 200 30
Motors intended for use in the vertical position LSES 250 MZ 360 380 200 30
may be delivered on a pallet in the horizontal LSES 250 ME 400 400 500 30
position. When the motor is pivoted, the shaft must under LSES 280 SC/SD/MC/MD 400 400 500 30
no circumstances be allowed to touch the ground, as the LSES 315 SN 400 400 500 30
bearings may be irreparably damaged. Moreover, LSES 315 SP/MP/MR 360 380 500 17
additional special precautions must be taken, as the
integral motor lifting rings are not designed for pivoting
the motor.
Horizontal position
Type
A e min h min Øt
• Horizontal position FLSES 100 152 200 150 22

FLSES 100 LG 145 200 150 22
FLSES 112 145 200 150 22
FLSES 132 180 200 150 25
FLSES 160 M/MU 200 260 150 14
FLSES 180 M/MUR/L/LUR 200 260 150 14
FLSES 200 LU 270 260 150 14
FLSES 225 SR/MR 270 260 150 14
FLSES 225 S/M 360 380 200 30
FLSES 250 M/MR 360 380 200 30
FLSES 280 360 380 500 30
A
FLSES 315 S/M/LA/LB 440 400 500 60
FLSES 355 545 500 500 60
FLSES/FLS 355LK 685 710 500 30
e 2 x Øt FLS 400 735 710 500 30
FLS 450 730 710 500 30
h
Horizontal position
Type
A e min h min Øt
PLSES 225 MG 310 300 300 30
PLSES 250 MF/SF 310 300 300 30
PLSES 280 MD/MGU/SGU 310 300 300 30
PLSES 315 SUR/MUR/L/LD/LUS 385 380 500 30
PLSES/PLS 315 LG/MGU/VLG/VLGU 450 750 550 48

4850 en - 2018.11 / f
SPARE PARTS
• Vertical position 8 - SPARE PARTS

When ordering spare parts, you must indicate the
complete motor type, its serial number and the information
e given on the nameplate (see section 1).
Part numbers can be found on the exploded views and
h
C
their descriptions in the parts list (section 6).

n x ØS
In the case of flange mounted motors, indicate the type of
flange and its dimensions (see below).
D
IM 3001 (IM B5)

E LA T
View from above Side view
Vertical position
Type M
C E D n** ØS e min* h min
NJ6
P
LSES 160 M/MU/L/LUR 320 200 230 2 14 320 350
LSES 180 MR 320 200 230 2 14 320 270
LSES 180 M/L/LUR 390 265 290 2 14 390 320 nØS
LSES 200 L/LR 410 300 295 2 14 410 450
LSES 200 LU 410 300 295 2 14 410 450
LSES 225 SR/MR 480 360 405 4 30 540 350
LSES 225 S/SG/M/MG 480 360 405 4 30 500 500 IM 3601 (IM B14)
LSES 250 MZ 480 360 405 4 30 590 550
T
LSES 250 ME 480 360 405 4 30 500 500 n Ø M.S
LSES 280 SC/SD/MC/MD 480 360 405 4 30 500 500
LSES 315 SN 480 360 405 4 30 500 500
M
LSES 315 SP/MP/MR 630 - 570 2 30 630 550
NJ6
P
Vertical position
Type
C E D n** ØS e min* h min
FLSES 160 M/MU 320 200 230 2 14 320 350
FLSES 180 M/MUR/L/LUR* 320 200 230 2 14 320 270
FLSES 200 LU 410 300 295 2 14 410 450
FLSES 225 SR/MR 410 300 295 2 14 410 450 Our extensive network of service centers can dispatch the
FLSES 225 S/M 480 360 405 4 30 540 350 necessary parts without delay.
FLSES 250 M/MR 480 360 405 4 30 590 550
FLSES 280 S 480 360 585 4 30 590 550 To ensure that our motors operate correctly and safely, we
FLSES 280 M 480 360 585 4 30 590 550 recommend the use of original manufacturer spare parts.
FLSES 315S/ M/LA/LB 620 - 715 2 35 650 550
FLSES 355 760 - 750 2 35 800 550 In the event of failure to comply with this advice, the
FLSES/FLS 355 LK 810 350 1135 4 30 810 600 manufacturer cannot be held responsible for any damage.
FLS 400 810 350 1135 4 30 810 600
FLS 450 960 400 1170 4 30 960 750
Type
C E
Vertical position
n** ØS e min* h min
9 - RECYCLING
PLSES 180 LG/LGU 430 270 2 14 430 450
At the end of life, we advise that you contact a salvage company
PLSES 200 M/LU/LR 400 280 2 14 400 450
to recycle the various motor components.
PLSES 225 MG 450 310 2 14 450 490
PLSES 250 SP/MP/MF 450 310 4 30 450 490
PLSES 280 SD 450 310 4 30 450 490
PLSES 280 MD/MG 450 310 4 30 450 490
PLSES 315 S/SUR 500 385 4 30 500 500
PLSES 315 M/MUR/L/LD/LDS/LU 500 385 4 30 500 500
PLSES 315 MG/MGU/LG 750 450 4 48 750 450
* if the motor is fitted with a drip cover, allow an additional 50 to 100 mm to

avoid damaging it when the load is swung.
** if n = 2, the lifting rings form an angle of 90° with respect to the terminal box
axis. if n = 4, this angle becomes 45°.

4850 en - 2018.11 / f
RECYCLING
DISMANTLING AND REASSEMBLY PROCEDURES
10 - LS/LSES motors..........................................................................................................26 to 35
11 - FLS/FLSES motors...................................................................................................36 to 45
12 - PLS/PLSES motors..................................................................................................46 to 51

4850 en - 2018.11 / f
LS/LSES MOTORS
10 - LS/LSES MOTORS
LS/LSES 71 LS/LSES 71
10.1 - LS/LSES 71 to 160 MP/LR motors foot mounted flange mounted (or foot/flange)
10.1.1 - Dismantling 6 59 5 6 59 60 5
- Remove the screws (27) and then take off the cover (13).
- Pull out the fan (7) using a hub remover or 2 levers (for
example, 2 screwdrivers) diametrically opposed to one
another, using the shield (6) for support.
- Remove the tie rods (14).
- Remove the key (21).
- Using a wooden mallet, tap the shaft on the fan side in order 7 50 30 39 7 50 30 39
to loosen the drive end shield (5). NDE DE NDE DE
- Remove the rotor shaft (3) and the DE shield (5) taking care
not to knock the winding.
- Remove the shield on the fan side (6). LS/LSES 80 - 90 LS/LSES 80 - 90
- Take out the preloading washer (59) and the seal of the NDE foot mounted flange mounted (or foot/flange)
shield (54) for LS/LSES 100, 112 and 132 motors.
- Remove the circlip (60) from flanged motors using angled 6 59 5 6 59 60 5
circlip pliers.
- Separate the DE shield from the rotor shaft.
- The shaft can then be seen with its 2 bearings and, if
appropriate, the circlip.
Use a bearing remover to take out the bearings, taking care not
to knock the running surfaces of the shaft.
7 50 30 308 7 50 30 39
10.1.2 - Reassembling motors without circlip
NDE DE NDE DE
- Mount the bearings on the rotor shaft.
- Insert the rotor into the stator taking all possible precautions
not to knock the winding. LS/LSES 100 - 112 - 132 LS/LSES 100 - 112 - 132
- Mount the DE shield (5). foot mounted flange mounted (or foot/flange)
- For LS/LSES 71 motors, mount the seal (39) with grease
beforehand. 6 59 5 6 59 60 5
- Place the preloading washer (59) in the bearing housing, then
mount the NDE shield (6).
- Place the tie rods (14) in position and tighten the nuts
diagonally up to the recommended torque (see section 6.4).
- Mount the shield seals (39, 54, 308) with grease.
- Mount the fan (7) using a drift to bed it into position.
- Check that the motor turns freely by hand and that there is no 54 50 30 308 54 50 30 39
radial play. NDE DE NDE DE
- Replace the cover (13) and fix it with the screws (27).
10.1.3 - Reassembling motors with flange and

LS/LSES 160 MP/LR LS/LSES 160 MP/LR
circlip foot mounted flange mounted (or foot/flange)
- Mount the DE bearing (30) in the flange (5) using the outer
slip-ring for support. 6 59 5 6 59 60 5
- Fit the circlip (60).
- Mount this assembly on the rotor (3) using the inner slip-ring
for support.
- Mount the NDE bearing on the rotor.
- Insert the rotor (3) and shield (5) assembly in the stator taking
care not to knock the winding.
- Place the preloading washer (59) in the bearing housing, then 54 50 30 308 54 50 30 39
mount the NDE shield (6). NDE DE NDE DE
- Check that the motor turns freely by hand and that there is no
axial play.
- Replace the key (21).

4850 en - 2018.11 / f
LS/LSES MOTORS
LS/LSES 71 to 160 MP/LR
71b
71a
13
27
78
508 98
85 54
84 50 59
21
7 14
6
2
30 26 85
IM B3
84
39
5
6
1
60
IM B14
39 5
26
IM B5
39
5
LS/LSES 71 to 160 MP/LR

Ref. Description Ref. Description Ref. Description
1 Wound stator 21 Drive end shield shaft extension key 60 Circlip
2 Frame 26 Nameplate 71 a Plastic terminal box (< or = frame size 112)
3 Rotor 27 Fan cover screw 71 b Metal terminal box
5 Drive end shield 30 Drive end bearing 84 Terminal block
6 Non drive end shield 39 Drive end seal 85 Set screw
7 Fan 50 Non drive end bearing 98 Connectors
13 Fan cover 54 NDE weatherproof seal 508 Terminal box plug
14 Tie rods 59 Preloading (wavy) washer

4850 en - 2018.11 / f
LS/LSES MOTORS
10.2 - LS/LSES 160 M/L/LU, 180 MT/LR

motors
10.2.1 - Dismantling LS/LSES 160 M/L/LU - 180 MT/LR
- Remove the screws (27) and then take off the cover (13). standard bearings
- Pull out the fan (7) using a hub remover or 2 levers diametrically 54 6 59 50 33 5 30 38 40 39
opposed to one another, using the shield (6) for support.
- Take out the key (21) and remove the seals (39 and 54 for foot
mounted motors) (54 for flange mounted motors).
- Remove the mounting screws (14).
- Unscrew the inner bearing retainer (33) fixing screws (40)
when using a flange mounted motor or if the drive end bearing
is locked.
- Using a bronze drift, remove the shields (5 and 6) by tapping
gently on the shield bosses. Recover the preloading washer NDE DE
(59).
- Remove the circlip (38) if necessary (flange mounted motor).
- Remove the rotor (3) from the stator (1) taking care not to
touch the winding. LS/LSES 160 M/L/LU - 180 MT/LR
- Take out the bearings (30) and (50) using a bearing remover, drive end roller bearings
while protecting the end of the shaft extension with a washer. 54 62 6 542 60 50 53 33 5 30 38 40 39
Avoid knocking the running surfaces of the shaft.
10.2.2 - Reassembly
- See section 6.1 before reassembly.
- If necessary, insert the inner bearing retainer (33) at the rotor
drive end, then mount new bearings on the shaft, see section
6.3 mounting bearings.
- Mount the circlip (38) for flange mounted motors.
NDE DE
- Insert the rotor (3) in the stator (1) taking care not to knock the
winding.
- Position the preloading washer (59) with a small amount of
grease in the back of the bearing cage of the NDE shield (6),
then remount the NDE shield (6), positioning it on the stator.
- If there is a bearing retainer (33), screw a rod with the same
thread diameter as the screws (40) into one of the tapped holes
of the bearing retainer to maintain its angular position when
remounting the DE shield (5).
- Remount the shield (5) taking care to allow for the positioning
of a bearing retainer if used.
- Place the mounting screws (14) in position and tighten the
nuts diagonally up to the recommended torque (see section
6.1).
- If necessary, fix the bearing retainer (33) with its own screws.
- Mount the shield seals with grease: (54 at the non drive end)
(39 at the drive end for foot mounted motors).
- Check that the rotor turns freely by hand (that there is no axial
play if there is a locked end shield).

4850 en - 2018.11 / f
LS/LSES MOTORS
LS/LSES 160 M/L/LU, 180 MT/LR
308
466
533
8
54
6
50
508
509
74
70
21
27
13
7
273
274
629
59
2
26
1
33
30 4
38
5
271
270
629
41
40
39
272 270
271
629
LS/LSES 160 M/L/LU, 180 MT/LR

1 Wound stator 30 Drive end bearing 271 Drive end shield fixing nut
2 Frame 33 Inner drive end bearing retainer 272 DE shield washer
3 Shaft 38 Snap ring for drive end shaft 273 Non drive end shield fixing screw
4 Rotor 39 Drive end seal 274 NDE shield fixing nut
5 Drive end shield 40 Drive end cover fixing screw 308 Cover fixing washer
Leaktight toothed lock washer for DE bearing
6 Non drive end shield 41 retainer
466 Snap ring for fan
7 Fan 50 Non drive end bearing 508 Terminal box plug
8 Fan key 54 NDE weatherproof seal 509 Cable gland seal
13 Fan cover 59 Preloading (wavy) washer 533 Cover shock mount
21 Drive end shield shaft extension key 70 Terminal box 629 Draining plug
26 Nameplate 74 Terminal box lid
27 Fan cover screw 270 Drive end shield fixing screw

4850 en - 2018.11 / f
LS/LSES MOTORS
10.3 - LS/LSES 180 L/LUR, 200 L/LR/LU, 225

ST/MT/MR, 250 MZ motors
10.3.1 - Dismantling
LS/LSES 180 L/LUR - 200 L/LR/LU
- Remove the screws (27) and then take off the cover (13). 225 ST/MT/MR - 250 MZ
- Pull out the fan (7) using a hub remover or 2 levers diametrically standard bearings
opposed to one another, using the shield (6) for support. 54 6 59 50 33 5 30 38 40 39
- Remove the mounting screws (270 + 273).
- Unscrew the inner bearing retainer (33) fixing screws (40) when
using a flange mounted motor or if the drive end bearing
is locked.
gently on the shield bosses. Recover the preloading washer (59).
- Remove the circlip (38) if appropriate. NDE DE
- Remove the rotor (3) from the stator (1) taking care not to touch
the winding.
- Take out the bearings (30) and (50) using a bearing remover,
while protecting the end of the shaft extension with a washer. Avoid LS/LSES 180 L/LUR - 200 L/LR/LU
225 ST/MT/MR - 250 MZ
knocking the running surfaces of the shaft. drive end roller bearings
54 62 6 542 60 50 53 33 5 30 38 40 39
10.3.2 - Reassembly
drive end, then mount new bearings on the shaft, see section 6.3
mounting bearings.
- Fill with new grease: the correct amount of new grease for the
- Mount the circlip (38) if necessary.
- Insert the rotor (3) in the stator (1) taking care not to knock the NDE DE
winding.
grease in the back of the bearing cage of the NDE shield (6), then
remount the NDE shield (6), positioning it on the stator.
thread diameter as the screws (40) into one of the tapped holes of
the bearing retainer to maintain its angular position when
- Remount the shield (5) taking care to allow for the positioning of
a bearing retainer if used.
- Place the mounting screws (14) in position and tighten the nuts
- If necessary, fix the bearing retainer (33) with the screws (40).

4850 en - 2018.11 / f
LS/LSES MOTORS
LS/LSES 180 L/LUR, 200 L/LR/LU, 225 ST/MT/MR, 250 MZ

466
8
7
54
6
59
50
28
25
29
508
74
70
1
4
3
21
42
272
270
13
27
273
33 275
30 556
38 319
5 322
39 323
41 321
26
40 2
320
629
643
270
271
LS/LSES 180 L/LUR, 200 L/LR/LU, 225 ST/MT/MR, 250 MZ

1 Wound stator 29 Lifting ring fixing washer 271 Drive end shield fixing nut
2 Frame 30 Drive end bearing 272 DE shield washer
3 Shaft 33 Inner drive end bearing retainer 273 Non drive end shield fixing screw
4 Rotor 38 Snap ring for drive end shaft 275 Fixing washer for NDE shield
5 Drive end shield 39 Drive end seal 319 Right foot
6 Non drive end shield 40 Drive end cover fixing screw 320 Left foot
7 Fan 41 retainer
321 Screws for feet
8 Fan key 42 Drive end grease nipples 322 Nut for feet
13 Fan cover 50 Non drive end bearing 323 Washer for feet
21 Drive end shield shaft extension key 54 NDE weatherproof seal 466 Snap ring for fan
25 Lifting ring 59 Preloading (wavy) washer 508 Terminal box plug
26 Nameplate 70 Terminal box 556 NDE bearing circlip
27 Fan cover screw 74 Terminal box lid 629 Draining plug
28 Lifting ring fixing screw 270 Drive end shield fixing screw 643 DE grease draining plug

4850 en - 2018.11 / f
LS/LSES MOTORS
10.4 - LS/LSES 225 MG, 250 ME/MF,

280 SC/MC, 280 SD/MD, 315 SN motors
10.4.1 - Dismantling LS/LSES 225 MG - 250 ME/MF
280 SC/MC/SD/MD - 315 SN
- Remove the screws (27), the grease nipple (42) and its extension, standard bearings
then take off the cover (13).
416
- Pull out the fan (7) using a hub remover or 2 levers diametrically 5 6
- Take out the key (21).
- Unscrew the DE bearing retainer (33) fixing screws (40) and NDE
bearing retainer (52) and (53) fixing screws (62), and remove
them.
gently on the shield bosses. Recover the preloading washer (59). 50
33 53
- Remove circlips (38) and (60).
- Remove the rotor (3) from the stator (1), taking care not to touch NDE DE
the winding with the inner bearing retainer.
while protecting the end of the shaft extension with a washer. Avoid
LS/LSES 225 MG - 250 ME/MF
knocking the running surfaces of the shaft.
280 SC/MC/SD/MD - 315 SN
- The bearings are removed either separately or with the bearing drive end roller bearings
retainers; to avoid damaging the bearing retainers, heat the outer
bearing retainer to make it easier to dismantle (the bearing should 54 62 63 60 542 6 50 52 33 30 38 5 41 40 39
be discarded).
10.4.2 - Reassembly
- Insert the inner bearing retainer (33) at the rotor drive end and the
inner bearing retainer (53) at the non drive end.
- Add new grease: the correct amount of new grease for the bearing
is 50% of the free space.
- Mount the new bearings on the shaft, see section 6.3 on mounting
bearings. NDE DE
- Mount the circlips (38) and (60).
winding.
- Screw a rod with the same thread diameter as the screws (40 and
62) into one of the tapped holes of the bearing retainers (33 and
53) to maintain their position and that of the grease nipple when
remounting the shields (5 and 6).
grease in the back of the bearing cage of the NDE shield (6), then
remount the NDE shield (6), positioning it on the stator.
- Fit the seal (54), the outer bearing retainer (52) and the locking
screws (62) for the bearing retainers (52, 53).
- Mount the shield (5) taking care to allow for the positioning of the
bearing retainer.
- Place the mounting screws (14), tighten the nuts diagonally
without locking them so that the feet of the protective cover can be
positioned when it is mounted.
- At the drive end fit the seal (39), insert the bearing retainer (32)
and the locking screws (40) for the bearing retainer.
- Mount the fan (7) using a drift to bed it in position or by heating the
hub of the aluminium fan to approximately 100°C.
axial play.
- Replace the cover (13), fixing it with the screws (27).
- Replace the grease nipple (42) and extension.
- Tighten the rod nuts (14) diagonally up to the torque recommended
in section 6.1.

4850 en - 2018.11 / f
LS/LSES MOTORS
LS/LSES 225 MG, 250 ME/MF, 280 SC/MC, 280 SD/MD, 315 SN
27 13
7 427 533
8
6 64 54
59
53 50
508
74
70
92
4
21 3
272 42
270 41
40
466
33 63 62
38 30 645 275 273
5 629
468 26
2
1
39
643 629
270 272
40 41
LS/LSES 225 MG, 250 ME/MF, 280 SC/MC, 280 SD/MD, 315 SN
1 Wound stator 38 Snap ring for drive end shaft 92 Terminal box baseplate
2 Frame 39 Drive end seal 270 Drive end shield fixing screw
3 Shaft 40 Drive end cover fixing screw 272 DE shield washer

4 Rotor 41 retainer
273 Non drive end shield fixing screw
5 Drive end shield 42 Drive end grease nipples 275 Fixing washer for NDE shield
6 Non drive end shield 50 Non drive end bearing 427 Cover plug
7 Fan 53 Inner non drive end bearing retainer 466 Snap ring for fan
8 Fan key 54 NDE weatherproof seal 468 Earth terminal plug
13 Fan cover 59 Preloading (wavy) washer 508 Terminal box plug
21 Drive end shield shaft extension key 62 Cover fixing screw 533 Cover shock mount
26 Nameplate 63 Fixing washer for NDE bearing retainer 629 Draining plug
27 Fan cover screw 64 Non drive end grease nipple 643 DE grease draining plug
30 Drive end bearing 70 Terminal box 645 NDE grease draining plug
33 Inner drive end bearing retainer 74 Terminal box lid

4850 en - 2018.11 / f
LS/LSES MOTORS
10.5 - LS/LSES 280 SU/SK/MK, - Mount the shield (5) at the drive end, positioning it on the
stator, then mount the fixed valve (34) in the shield bearing
315 (except SN) motors housing.
10.5.1 - Dismantling - Mount the mobile valve (35) by either screwing it or locking it,
- Remove the screws (27), the grease nipple (42) and its having carefully installed the seal (39) on the valve.
extension, then take off the cover (13). - Mount the outer bearing retainer (32) with the bearing retainer
- Pull out the fan (7) using a hub remover or 2 diametrically locking screws (40), making sure that the grease drain hole is
opposed levers, using the shield (6) for support; for an at the bottom.
aluminium fan, heat the hub to approximately 100°C before - Put the tie rods (14) in place, not forgetting the feet of the
protective cover (380), tighten the nuts diagonally without
removing it.
locking them so that the feet of the protective cover can be
positioned when it is mounted.
- Unscrew the tie rods (14) then remove them.
- Mount the fan (7) using a drift to bed it in position or by heating
- Unscrew the DE bearing retainer (33) fixing screws (40) and the hub of the aluminium fan to approximately 100°C.
NDE bearing retainer (32) and (52) fixing screws (62), and - Check that the motor turns freely by hand and that there is no
remove the bearing retainers. axial play.
- Unscrew the «CHc» screws of the mobile valves (35 and 56) - Replace the protective cover (13) and fix it with the screws
then unscrew the valves using a hook spanner or a conical (27), replace the grease nipple (42) and its extension.
bronze drift; unscrew the valves by hand and remove them. - Tighten the rod nuts (14), always diagonally, up to the torque
The valves hold the seal (39 and 54). recommended in section 6.1.
- Remove the fixed valves (34 and 35) from the bearing - Replace the key (21).
housings.
gently on the shield bosses.
LS/LSES 280 SU/SK/MK - 315
- Check that the bearing retainer (53) is smaller in diameter standard bearings
than the stator, otherwise remove the bearing (50) as per the
52 6 59 53 33 5 32
following instructions.
- Remove the rotor (3) from the stator (1) at the drive end, 62 40
taking care not to touch the winding with the inner bearing
retainer if there is no internal turbine. 55
while protecting the end of the shaft extension with a washer.
Avoid knocking the running surfaces of the shaft.
56 54 50 30 34 35 39
- The bearings are removed either separately or with the
bearing retainers (33 and 53); to avoid damaging the bearing NDE DE
retainers, heat the outer bearing ring (the bearing should be
discarded).
- Recover the preloading washer or springs (59) from the
LS/LSES 280 SU/SK/MK - 315
bearing retainer (53). drive end roller bearings
10.5.2 - Reassembly 52 55 6 53 33 5 32
- See section 6.1 before reassembly. 62 40

- Insert the inner bearing retainer (33) at the rotor drive end and
the inner bearing retainer (53) at the non drive end, not
forgetting to insert the preloading springs (59).
- Add new grease: the correct amount of new grease for the
- Mount the new bearings (30 and 50) on the shaft, see section 56 54 50 30 34 35 39
6.3 on mounting bearings. NDE DE
winding.
- Screw a rod with the same thread diameter as the screws (40)
and (62) into one of the tapped holes of the bearing retainers
(33) and (53) to maintain the position of the grease nipple when
remounting the shields (5 and 6).
- Check that the preloading springs are properly installed.
- Fit the NDE shield (6), positioning it on the stator, then mount
the fixed valve (55) in the shield bearing housing.
- Mount the mobile valve (56) by either screwing it or locking it,
having carefully installed the seal (54) on the valve.
- Mount the outer bearing retainer (52) with the bearing retainer
locking screws (62), making sure that the grease drain hole is
at the bottom.

4850 en - 2018.11 / f
LS/LSES MOTORS
LS/LSES 280 SU/SK/MK, 315 (except SN)
13
74 27
81 7
70 14
52
42 54
6
53
1
21
30
42
34
39
35
62
56
32 55
380
50
59
2
3
40 33
LS/LSES 280 SU/SK/MK, 315 (except SN)

1 Wound stator 30 Drive end bearing 53 Inner non drive end bearing retainer
2 Frame 32 Outer drive end bearing retainer 54 NDE weatherproof seal
3 Rotor 33 Inner drive end bearing retainer 55 Non drive end fixed grease valve
5 Drive end shield 34 Drive end fixed grease valve 56 Non drive end mobile grease valve
6 Non drive end shield 35 Drive end mobile grease valve 59 Preloading washer or spring
7 Fan 39 Drive end seal 62 Cover fixing screw
13 Fan cover 40 Drive end cover fixing screw 70 Terminal box
14 Tie rods 42 Grease nipples 74 Terminal box lid
21 Shaft extension key 50 Non drive end bearing 81 Cable gland support plate
27 Fan cover screw 52 Outer non drive end bearing retainer 380 Protective cover feet

4850 en - 2018.11 / f
FLS/FLSES MOTORS
11 - FLS/FLSES MOTORS
11.1 - FLS/FLSES 80 to 132 motors
11.1.1 - Dismantling FLS/FLSES 80 to 132
- Remove the screws (27) and then take off the cover (13). foot mounted
- Pull out the fan (7) using a hub remover or 2 levers (for example,
2 screwdrivers) diametrically opposed to one another, using the 6 59 5
shield (6) for support.
- Remove the tie rods (14).
- Remove the key (21).
- Using a wooden mallet, tap the shaft on the fan side in order to
loosen the drive end shield (5).
- Remove the rotor shaft (3) and the DE shield (5) taking care not
to knock the winding. 54 50 30 308
- Remove the shield on the fan side (6).
- Recover the preloading (wavy) washer (59) and the NDE shield NDE DE
seal (54).
- Remove the circlip (60) from flanged motors using angled circlip
pliers. FLS/FLSES 80 to 132
- Separate the DE shield from the rotor shaft. flange mounted (or foot/flange)
- The shaft can then be seen with its 2 bearings and, if appropriate,
the circlip. 6 59 60 5
Use a bearing remover to take out the bearings, taking care not to
knock the running surfaces of the shaft.
11.1.2 - Reassembling motors without circlip

- Mount the bearings on the rotor shaft.
- Insert the rotor into the stator taking all possible precautions not
to knock the winding. 54 50 30 39
- Mount the DE shield (5).
- Place the preloading washer (59) in the bearing housing, then NDE DE
- Place the tie rods (14) in position and tighten the nuts diagonally
up to the recommended torque (see section 6.4).
radial play.
11.1.3 - Reassembling motors with flange and

circlip
- Mount the DE bearing (30) in the flange (5) using the external
slip-ring for support.
- Fit the circlip (60).
- Mount this assembly on the rotor (3) using the inner slip-ring for
support.
- Mount the NDE bearing on the rotor.
- Insert the rotor (3) and shield (5) assembly in the stator taking
care not to knock the winding.
- Place the preloading washer (59) in the bearing housing, then
- Place the tie rods (14) in position and tighten the nuts diagonally
up to the recommended torque (see section 6.4).
axial play.

4850 en - 2018.11 / f
FLS/FLSES MOTORS
FLS/FLSES 80 to 132
71
27 13
508
54
85 59
98 84
3
21
50 6 14
2 7
98
85
26 84
30
60
308 5
IM B3 1
IM B14
39 26
5
IM B5
5
39
FLS/FLSES 80 to 132
1 Wound stator 21 Shaft extension key 60 Circlip
2 Frame 26 Nameplate 71 FLSES terminal box
3 Rotor 27 Fan cover screw 84 Terminal block
5 Drive end shield 30 Drive end bearing 85 Set screw
6 Non drive end shield 39 Drive end seal 98 Connectors
7 Fan 50 Non drive end bearing 308 Labyrinth seal
13 Fan cover 54 NDE weatherproof seal 508 Terminal box plug
14 Tie rods 59 Preloading (wavy) washer

4850 en - 2018.11 / f
FLS/FLSES MOTORS
11.2 - FLS/FLSES 160, 180 MR motors

- Remove the screws (27) and then take off the cover (13).
- Pull out the fan (7) using a hub remover or 2 levers diametrically
opposed to one another, using the shield (6) for support. FLS/FLSES 160 - 180 MR
standard bearings
mounted motors) (54 for flange mounted motors). 54 6 59 50 33 5 30 38 40 39
is locked.
gently on the shield bosses. Recover the preloading washer
(59).
- Remove the circlip (38) if necessary (flange mounted motor).
- Remove the rotor (3) from the stator (1) taking care not to NDE DE
touch the winding.
while protecting the end of the shaft extension with a washer.
Avoid knocking the running surfaces of the shaft. FLS/FLSES 160 - 180 MR
drive end roller bearings
54 62 6 542 60 50 53 33 5 30 38 40 39
11.2.2 - Reassembly
winding.
- Position the preloading washer (59) with a small amount of NDE DE
6.1).

4850 en - 2018.11 / f
FLS/FLSES MOTORS
FLS/FLSES 160, 180 MR
81 308
70
74
8 466 533
6 54
50
3
21
13 27
7
273
59 629
2 26
1
4
30 33
38
5
41 629 270
39 40
272 270
629 271
FLS/FLSES 160, 180 MR

1 Wound stator 27 Fan cover screw 74 Terminal box lid
2 Frame 30 Drive end bearing 81 Cable gland support plate
3 Shaft 33 Inner drive end bearing retainer 270 Drive end shield fixing screw
4 Rotor 38 Snap ring for drive end shaft 271 Drive end shield fixing nut
5 Drive end shield 39 Drive end seal 272 DE shield washer
6 Non drive end shield 40 Drive end cover fixing screw 273 Non drive end shield fixing screw
7 Fan 41 retainer
308 Cover fixing washer
8 Fan key 50 Non drive end bearing 466 Snap ring for fan
13 Fan cover 54 NDE weatherproof seal 533 Cover shock mount
21 Drive end shield shaft extension key 59 Preloading (wavy) washer 629 Draining plug
26 Nameplate 70 Terminal box

4850 en - 2018.11 / f
FLS/FLSES MOTORS
11.3 - FLS/FLSES 180 M/L/LUR, 200 LU,

225 MR/SR motors
- Remove the screws (27) and then take off the cover (13). FLS/FLSES 180 M/L/LUR - 200 LU
225 MR/SR
- Pull out the fan (7) using a hub remover or 2 levers diametrically standard bearings
- Take out the key (21) and remove the seals (39 and 54 for foot 54 6 59 50 33 5 30 38 40 39

is locked.
(59).
- Remove the circlip (38) if necessary (flange mounted motor). NDE DE
- Remove the rotor (3) from the stator (1) taking care not to
touch the winding.
FLS/FLSES 180 M/L/LUR - 200 LU
while protecting the end of the shaft extension with a washer. 225 MR/SR
Avoid knocking the running surfaces of the shaft. drive end roller bearings
54 62 6 542 60 50 53 33 5 30 38 40 39
11.3.2 - Reassembly
winding.
- Position the preloading washer (59) with a small amount of NDE DE
6.1).

4850 en - 2018.11 / f
FLS/FLSES MOTORS
FLS/FLSES 180 M/L/LUR, 200 LU, 225 MR/SR
466
7
8
54
6
81 59
74 50
70
1
4
3
21
13
27
42
272
270
273
275
629
556
26
2
33
30
38
5
39
41
629
643
40
270
271
FLS/FLSES 180 M/L/LUR, 200 LU, 225 MR/SR

1 Wound stator 30 Drive end bearing 81 Cable gland support plate
2 Frame 33 Inner drive end bearing retainer 270 Drive end shield fixing screw
3 Shaft 38 Snap ring for drive end shaft 271 Drive end shield fixing nut
4 Rotor 39 Drive end seal 272 DE shield washer
5 Drive end shield 40 Drive end cover fixing screw 273 Non drive end shield fixing screw
275 Fixing washer for NDE shield
7 Fan 42 Drive end grease nipples 466 Snap ring for fan
8 Fan key 50 Non drive end bearing 556 NDE bearing circlip
13 Fan cover 54 NDE weatherproof seal 629 Draining plug
21 Drive end shield shaft extension key 59 Preloading (wavy) washer 643 DE grease draining plug
26 Nameplate 70 Terminal box
27 Fan cover screw 74 Terminal box lid

4850 en - 2018.11 / f
FLS/FLSES MOTORS
11.4 - FLS/FLSES 225 M to 280 motors From now on, we recommend checking at every step that
the rotor turns freely by hand before continuing to the next
11.4.1 - Dismantling the NDE shield instruction.
- Remove the fixing screws (27) and then take off the cover - Replace the shield fixing screws (270) and (273).
(13). - Insert the fixing screws on the inner bearing retainers (33) and
- Remove the shaft extension screw if necessary. (53). Replace the AZ washers to ensure a perfect seal.
- Take out the fan (7). - Replace the fan key if appropriate.
- Remove the fixing screws from the inner NDE bearing retainer - Replace the fan (7).
(53). - Replace the shaft extension screw if necessary.
- Remove the fixing screws (273) from the NDE shield (6). - Replace the cover (13) and reinsert the fixing screws (27).
- Remove the fan key if appropriate. - Lubricate the DE and NDE antifriction bearings, turning the
- Using two levers or a flexible hammer, disengage the NDE shaft by hand.
shield (6) taking care not to place it aslant. Remove the shield
Amount of grease for ball bearings:
by sliding it along the shaft.
- Frame size 225 - 250: DE and NDE = 120 cm3
- Put the dismantled components to one side and recover the
- Frame size 280: DE = 170 cm3 / NDE = 120 cm3
preloading washer (59), which should be replaced in its
housing.
11.4.2 - Dismantling the DE shield FLS/FLSES 225 M to 280

- Dismantle the DE shield without removing the rotor (3). To do standard bearings
this:
- Remove the fixing screws (270) from the DE shield (5). 5
416
6
- Remove the fixing screws (40) from the DE internal cover
(33).
- Using two levers or a flexible hammer, disengage the DE
shield (5) taking care not to place it aslant.
- Remove the shield by sliding it along the shaft.
11.4.3 - Changing the antifriction bearings 50

33 53
- Using an appropriate lifting tool, take out the rotor without
knocking the winding. NDE DE
- Take off the DE circlip (38).
- Remove the bearings (30) and (50) with an appropriate tool,
protecting the end of the shaft extension. Avoid knocking the FLS/FLSES 225 M to 280
running surfaces of the shaft. drive end roller bearings
- Change the bearings in accordance with the instructions
5 416 6
described in the General information in section 6 (shrinkfitting
only).
IMPORTANT : Before undertaking any of these procedures,
read the «CHECKS BEFORE REASSEMBLY» section.
11.4.4 - Reassembly
- Mount the DE bearing (30) on the rotor shaft (take care not to
forget the inner bearing retainer (33) and the circlip (38)!), and 50
also the NDE bearing (50) if and only if the stator inner Ø allows 33 53
the inner NDE bearing retainer (53) to pass through. NDE DE

- Insert the rotor into the stator taking care not to knock the
winding. Install the NDE bearing if this has not already been
done.
- Fill the decompression grooves (416) located in the shaftway
with grease.
- Present the shields, grease nipples facing upwards. Begin
with the DE shield (5). Fix a dowel pin in one of the inner bearing
retainer (33) tapped holes so that the grease inlet pipes fully
correspond.
- End with the NDE shield (6). Fix a dowel pin in one of the
inner bearing retainer (53) tapped holes so that the grease
inlet pipes fully correspond.
- Lift the rotor slightly and fit the shields in place.

4850 en - 2018.11 / f
FLS/FLSES MOTORS
FLS/FLSES 225 M to 280
74
75
77 27 13
64
81
70
69
26
3
33 21
38 30
42 5
11
10
12
7
273
456
40 59
50
53
270
271 2
406
1
5
FLS/FLSES 225 M to 280

1 Wound stator 26 Nameplate 69 Terminal box base seal
2 Frame 27 Fan cover screw 70 Terminal box
3 Rotor 30 Drive end bearing 74 Terminal box lid
5 Drive end shield 33 Inner drive end bearing retainer 75 Terminal box lid fixing screw
6 Non drive end shield 38 Snap ring for drive end shaft 77 Terminal box lid seal
7 Fan 40 Drive end cover fixing screw 81 Cable gland support plate
10 Turbine or fan screw 42 Drive end grease nipples 270 Drive end shield fixing screw
11 Lockwasher 50 Non drive end bearing 271 Drive end shield fixing nut
12 Lock washer 53 Inner non drive end bearing retainer 273 Non drive end shield fixing screw
13 Fan cover 59 Preloading (wavy) washer 406 Drive end grease valve cover plate (plug)
21 Drive end shield shaft extension key 64 Non drive end grease nipple 456 Non drive end grease valve cover plate (plug)

4850 en - 2018.11 / f
FLS/FLSES MOTORS
11.5 - FLS/FLSES 315 to 355 LD motors From now on, we recommend checking at every step that
the rotor turns freely by hand before continuing to the next
11.5.1 - Dismantling the NDE shield instruction.
- Remove the fixing screws (27) and then take off the cover - Replace the shield fixing screws (270) and (273).
(13). - Insert the fixing screws on the inner bearing retainers (33) and
- Remove the shaft extension screw if necessary. (53). Replace the AZ washers to ensure a perfect seal.
- Take out the fan (7). - Replace the fan key if appropriate.
- Remove the fixing screws from the inner NDE bearing retainer - Replace the fan (7).
(53). - Replace the shaft extension screw if necessary.
- Remove the fixing screws (273) from the NDE shield (6). - Replace the cover (13) and reinsert the fixing screws (27).
- Remove the fan key if appropriate. - Lubricate the DE and NDE antifriction bearings, turning the
- Using two levers or a flexible hammer, disengage the NDE shaft by hand.
shield (6) taking care not to place it aslant. Remove the shield Amount of grease for ball bearings:
by sliding it along the shaft. - Frame size 315 : DE and NDE = 50 g for 4P and + / 35 g for 2P
- Put the dismantled components to one side and retrieve the - Frame size 355 : DE and NDE = 60 g for 4P and + / 35 g for 2P
preloading springs (256), which should be replaced in their
housing.
11.5.2 - Dismantling the DE shield

- Dismantle the DE shield without removing the rotor (3). To do
this:
FLS/FLSES 315 to 355 LD
- Remove the fixing screws (270) from the DE shield (5). standard bearings
- Remove the fixing screws (40) from the DE internal cover
(33). 416
5 6
- Using two levers or a flexible hammer, disengage the DE
shield (5) taking care not to place it aslant.
- Remove the shield by sliding it along the shaft.
11.5.3 - Changing the antifriction bearings

- Using an appropriate lifting tool, take out the rotor without
knocking the winding.
50
- Remove the DE (38) and NDE (60) circlips. 33 53
- Remove the bearings (30) and (50) with an appropriate tool,
NDE DE
protecting the end of the shaft extension. Do not knock the
running surfaces of the shaft.
- Change the bearings in accordance with the instructions
described in the General information in section 6 (shrinkfitting drive end roller bearings
only).
IMPORTANT : Before undertaking any of these procedures, 416
5 6
read the «CHECKS BEFORE REASSEMBLY» section.
11.5.4 - Reassembly
- Mount the DE bearing (30) on the rotor shaft (take care not to
forget the inner bearing retainer (33) and the circlip (38)!), and
also the NDE bearing (50) if and only if the stator inner Ø allows
the inner NDE bearing retainer (53) to pass through, refit the
circlip (60), refit the preloading springs in their housing in the
50
inner NDE bearing retainer (53). 33 53
- Insert the rotor into the stator taking care not to knock the
NDE DE
winding. Install the NDE bearing if this has not already been
done.
- Fill the decompression grooves (416) located in the shaftway
and the grease inlet pipes with grease.
- Present the shields, grease nipples facing upwards. Begin
with the DE shield (5). Fix a dowel pin in one of the inner bearing
retainer (33) tapped holes so that the grease inlet pipes fully
correspond.
- End with the NDE shield (6). Fix a dowel pin in one of the inner
bearing retainer (53) tapped holes so that the grease inlet
pipes fully correspond.
- Lift the rotor slightly and fit the shields in place.

4850 en - 2018.11 / f
FLS/FLSES MOTORS

10
12 11
275 273
74 65 64
70
81 256 6
25
26
1
4
3
42
272 13
270
27
7
62
63
456
629
60
50
53
468 25
2
21
33
30
38
42
5
629
406
41
40
629
406
270 272

1 Wound stator 27 Fan cover screw 70 Stator terminal box
2 Frame 30 Drive end bearing 74 Stator terminal box lid
3 Shaft 33 Inner drive end bearing retainer 81 Cable gland support plate
4 Rotor 38 Snap ring for drive end shaft 256 Preloading spring
5 Drive end shield 40 Drive end cover fixing screw 270 Drive end shield fixing screw
272 DE shield washer
7 Fan 42 Drive end grease nipples 273 Non drive end shield fixing screw
10 Turbine or fan screw 50 Non drive end bearing 275 Fixing washer for NDE shield
11 Lockwasher 53 Inner non drive end bearing retainer 406 Drive end grease valve cover plate
12 Lock washer 60 Circlip 456 Non drive end grease valve cover plate
13 Fan cover 62 Cover fixing screw 468 Earth terminal plug
21 Drive end shield shaft extension key 63 Fixing washer for NDE bearing retainer 629 Draining plug
25 Lifting ring 64 Non drive end grease nipple
26 Nameplate 65 Extension for non drive end grease nipple

4850 en - 2018.11 / f
PLS/PLSES MOTORS
12 - PLS/PLSES MOTORS
12.1 - PLS/PLSES 180 LG/LGU PLS/PLSES 180 LG/LGU
200 M/L/LP/LU/LR, 225 MR motors 200 M/L/LP/LU/LR
standard bearings
6 59 53 33 5 40
- Remove the screws (27) and grease nipple (64), then take off
the cover (13).
62
- Pull out the fan (7) using a hub remover or 2 diametrically
opposed levers, using the shield (6) for support, then remove
the fan key or pin.
- Unscrew the tie rods (14) then remove them.
- Unscrew the DE bearing retainer (33) fixing screws (40) and
54 50 30 38 39
NDE bearing retainer (53) fixing screws (62), and remove
them. NDE DE
(59). PLS/PLSES 225 MR
- Remove the circlip (38) and if necessary the circlip (60) (motor standard bearings
with roller bearing).
6 59 53 33 5 40
- Remove the rotor (3) from the stator (1) at the drive end,
taking care not to touch the winding with the inner bearing
62
retainer. Take out the bearings (30) and (50) using a bearing
remover, while protecting the end of the shaft extension with a
washer. Take care not to knock the running surfaces of the
shaft.
bearing retainers; to avoid damaging the bearing retainers,
54 50 30 38 39
heat the inner bearing retainer to make it easier to dismantle
(the bearing should be discarded).
NDE DE
12.1.2 - Reassembly
- Insert the inner bearing retainer (33) at the rotor drive end and PLS/PLSES 180 LG/LGU
200 M/L/LP/LU/LR - 225 MR
the inner bearing retainer (53) at the non drive end. drive end roller bearings
- Fit the new bearings on the shaft, see section 6.1 on mounting
bearings. 6 53 33 5 40
- Insert the rotor (3) in the stator (1) taking every precaution not
to knock the winding. 62
(33) and (53) to maintain the position of the grease nipple when
refitting the shields (5 and 6).
grease at the back of the bearing cage of the NDE shield (6), 54 60 50 30 38 39
then remount the NDE shield (6) by positioning it on the stator. NDE DE
- Fit the shield (5) taking care to position the bearing retainer
(33) correctly.
- Fix the bearing retainers (33) and (53) with their own screws Bearing g
(40) and (62). 6212 Z 31
- Mount the shield seals with grease: (54) for the non drive end, 6214 60
(39) for the drive end. 6312 or NU312 90
- Install the fan key or pin. 6313 or NU313 93
- Mount the fan (7) using a drift to bed it into position. 6314 or NU314 140
MAKE SURE it is facing the right way!
- Check that the rotor turns freely by hand (that there is no axial (Weight valid for POLYREX EM103 grease with immaculately
play if there is a locked end shield). clean grease track + bearing seat + drain holes).
- Replace the grease nipple (64).
- Fill with new grease: the quantity is indicated in the table
opposite.
Turn the shaft by hand during greasing.

4850 en - 2018.11 / f
PLS/PLSES MOTORS
PLS/PLSES 180 LG/LGU, 200 M/L/LP/LU/LR, 225 MR
64 1 70 74 84 2 5 14
110
6
42
53
39
50
59
54
30
13
21
3
33
27
PLS/PLSES 180 LG/LGU, 200 M/L/LP/LU/LR, 225 MR

1 Wound stator 21 Key 54 Non drive end seal
2 Frame 27 Fan cover screw 59 Preloading (wavy) washer
3 Rotor 30 Drive end bearing 64 Grease nipple
5 Drive end shield 33 Inner drive end bearing retainer 70 Terminal box
6 Non drive end shield 39 Drive end seal 74 Terminal box lid
7 Fan 42 Grease nipple 84 Terminal block
13 Fan cover 50 Non drive end bearing 110 Protective grille
14 Tie rods 53 Inner non drive end bearing retainer

4850 en - 2018.11 / f
PLS/PLSES MOTORS
12.2 - PLS/PLSES 225 MG, 250, - Put the tie rods (14) in place, not forgetting the feet of the
protective cover (380), tighten the nuts diagonally without
280 SC/SD/MC/MD motors locking them so that the feet of the protective cover can be
12.2.1 - Dismantling positioned when it is mounted.
- Remove the screws (27), the grease nipple (64) and its - Install the fan key.
extension (65), then take off the cover (13). - Mount the fan (7) using a drift to bed it in position or by heating
- Pull out the fan (7) using a hub remover or 2 diametrically the hub of the aluminium fan to approximately 100°C.
opposed levers, using the shield (6) for support, then remove MAKE SURE it is facing the right way!
the fan key. - Check that the motor turns freely by hand and that there is no
- Take out the key (21). axial play.
- Unscrew the tie rods (14) then remove them. - Replace the protective cover (13) and fix it with the screws
- Unscrew the DE bearing retainer (33) and (32) fixing screws (27), replace the grease nipple (64) and its extension (65).
(40) and NDE bearing retainer (52) and (53) fixing screws (62),
- Tighten the rod nuts (14), always diagonally, up to the torque
and remove them.
recommended in section 6.1.
- Unscrew the «Hc» screw of the mobile valve (35) then
- Fill with new grease: the quantity is indicated in the table
unscrew the valve using a hook key or a conical bronze drift;
unscrew the valve by hand and remove it. The valve holds the below.
seal (39) and its support (386) in place. Turn the shaft by hand during greasing.
- Using a bronze drift, remove the shields (5 and 6) by tapping - Replace the key (21).
(59).
- Remove the circlip (60). PLS/PLSES 225 MG - 250
- Remove the rotor (3) from the stator (1) at the drive end, 280 SC/SD/MC/MD
taking care not to touch the winding with the inner bearing standard bearings
retainer. 6 59 33 5 32
- Take out the bearings (30) and (50) using a bearing remover, 52 40
while protecting the end of the shaft end with a washer. Take 62 39
care not to knock the running surfaces of the shaft.
386
- The bearings are removed either separately or with the 54
bearing retainers; to avoid damaging the bearing retainers, 388

35
heat the inner bearing retainer to make it easier to dismantle

(the bearing should be discarded).
60 50 53 30
12.2.2 - Reassembly
- See section 6.1 before reassembly. NDE DE
the inner bearing retainer (53) at the non drive end.
PLS/PLSES 225 MG - 250
- Fit the new bearings on the shaft, see section 6.1 on mounting 280 SC/SD/MC/MD
bearings. drive end roller bearings
- Mount the circlip (60).
6 33 5 40
- Insert the rotor (3) in the stator (1) taking every precaution not 52
32
to knock the winding. 62 39
54 386
35
(33) and (53) to maintain the position of the grease nipple when 388

60 50 53 30
grease at the back of the bearing cage of the NDE shield (6),
then remount the NDE shield (6) by positioning it on the stator. NDE DE
- At the non drive end fit the seal (54) and its support (388),
insert the bearing retainer (52) and the locking screws (62) for
the bearing retainers (52) and (53).
- At the drive end fit the shield (5) taking care to position the Bearing g
bearing retainer (33) correctly. 6314 105
- Mount the mobile valve (35) by either screwing it or locking it 6315 140
having carefully mounted the seal (39) and its support (386). 6317 or NU317 180
- Mount the shield seals with grease: (54) for the non drive end, 6318 or NU318 220
(39) for the drive end.
- Mount the outer bearing retainer (32) with the bearing retainer (Weight valid for POLYREX EM103 grease with immaculately
clean grease track + bearing seat + drain holes).
at the bottom.

4850 en - 2018.11 / f
PLS/PLSES MOTORS
PLS/PLSES 225 MG, 250, 280 SC/SD/MC/MD
65
6 64 118 2 1 70 74 84 42 5 33
53
30
411
32
13
39
59
386
50
387
52
35
54
36
388
7 3
21
27
380 14
PLS/PLSES 225 MG, 250, 280 SC/SD/MC/MD

1 Wound stator 32 Outer drive end bearing retainer 65 Extension for grease nipple
2 Frame 33 Inner drive end bearing retainer 70 Terminal box
3 Rotor 35 Drive end mobile grease valve 74 Terminal box lid
5 Drive end shield 39 Drive end seal 84 Terminal block
6 Non drive end shield 42 Grease nipple 118 Internal deflector
7 Fan 50 Non drive end bearing 380 Protective cover feet
13 Fan cover 52 Outer non drive end bearing retainer 386 Drive end seal support
14 Tie rods 53 Inner non drive end bearing retainer 388 Non drive end seal support
21 Key 54 Non drive end seal 411 External deflector
27 Fan cover screw 59 Preloading (wavy) washer
30 Drive end bearing 64 Grease nipple

4850 en - 2018.11 / f
PLS/PLSES MOTORS
12.3 - PLS/PLSES 280 MG, 315 motors - Put the tie rods (14) and the feet of the protective cover (380)
in place, tighten the nuts diagonally without locking them so
12.3.1 - Dismantling that the feet of the protective cover can be positioned when it
- Remove the screws (27), the grease nipple (64) and its is mounted.
extension (65), then take off the cover (13). - Install the fan key.
- Pull out the fan (7) using a hub remover or 2 diametrically - Mount the fan (7) using a drift to bed it in position or by heating
opposed levers, using the shield (6) for support; for an the hub of the aluminium fan to approximately 100°C.
aluminium fan, heat the hub to approximately 100°C before MAKE SURE it is facing the right way!
removing it. - Check that the motor turns freely by hand and that there is no
- Take out the key (21). axial play.
- Unscrew the mounting screws (14) then remove them. - Replace the protective cover (13) and fix it with the screws
- Unscrew the DE bearing retainer (32) and (33) fixing screws (27), replace the grease nipple (64) and its extension (65).
(40) and NDE bearing retainer (52) and (53) fixing screws (62), - Fill with new grease: the quantity is indicated in the table
and remove them. below. Turn the shaft by hand during greasing.
- Unscrew the «Hc» screws of the mobile valves (35 and 56) - Tighten the nuts (14), always diagonally, up to the torque
then unscrew the valves using a pin spanner; unscrew the recommended in section 6.1.
valves by hand and remove them. - Replace the key (21).
The valves hold the supports (386) and (388) for the seals (39
and 54) in place.
gently on the shield bosses.
PLS/PLSES 280 MG - 315
- Check that the bearing retainer (53) is smaller in diameter
standard bearings
than the stator, otherwise remove the bearing (50) as per the
following instructions.
- Remove the rotor (3) from the stator (1) at the drive end, 62 6 59 33 5 40
taking care not to touch the winding with the inner bearing 32
52
retainer if there is no internal turbine. Take out the bearings 39
(30) and (50) using a bearing remover, while protecting the end 54 386
of the shaft end with a washer. Take care not to knock the
388 35
running surfaces of the shaft.
bearing retainers (33 and 53); to avoid damaging the bearing 56 50 53 30
retainers, heat the inner bearing ring (the bearing should be
discarded). NDE DE
- Recover the preloading washer or springs (59) from the
bearing retainer (53).
12.3.2 - Reassembly PLS/PLSES 280 MG - 315
drive end roller bearings
the inner bearing retainer (53) at the non drive end, not 62 6 33 5 40
forgetting to insert the preloading springs (59) with a little 32
52
grease. 39
- Fit the new bearings (30 and 50) on the shaft, see section 6.1 54 386
on mounting bearings.
- Insert the rotor (3) in the stator (1) taking every precaution not 388 35
to knock the winding.
- Screw a rod with the same thread diameter as the screws (40) 56 50 53 30
(33) and (53) to maintain the position of the grease nipple when NDE DE
- Check that the preloading springs are properly installed.
- Mount the NDE shield (6) by positioning it on the stator.
- Mount the mobile valve (56) by either screwing it or locking it,
having carefully installed the seal (54) with its support (388). Bearing g
- Mount the outer bearing retainer (52) with the bearing retainer
6316 160
6320 385
at the bottom.
- Mount the DE shield (5) by positioning it on the stator. NU320 385
- Mount the mobile valve (35) by either screwing it or locking it, 6219 215
having carefully installed the seal (39) with its support (386). 6224 244
- Mount the shield seals with grease: (54) for the non drive end,
(39) for the drive end. (Weight valid for POLYREX EM103 grease with immaculately
- Mount the outer bearing retainer (32) with the bearing retainer clean grease track + bearing seat + drain holes).
at the bottom.

4850 en - 2018.11 / f
PLS/PLSES MOTORS
PLS/PLSES 280 MG, 315
65
53 13 64 6 118 74 70 2 1 5 42
33
390
30
59
386
411
39
7
35
52
388
54
56
3
50
21
14
27 32
380
PLS/PLSES 280 MG, 315

1 Wound stator 32 Outer drive end bearing retainer 64 Grease nipple
2 Frame 33 Inner drive end bearing retainer 65 Extension for grease nipple
3 Rotor 35 Drive end mobile grease valve 70 Terminal box
5 Drive end shield 39 Drive end seal 74 Terminal box lid
6 Non drive end shield 42 Grease nipple 84 Terminal block
7 Fan 50 Non drive end bearing 118 Internal deflector
13 Fan cover 52 Outer non drive end bearing retainer 380 Protective cover feet
14 Tie rods 53 Inner non drive end bearing retainer 386 Drive end seal support
21 Key 54 Non drive end seal 388 Non drive end seal support
27 Fan cover screw 56 Non drive end mobile grease valve 390 Non drive end inner bearing retainer strut
30 Drive end bearing 59 Preloading (wavy) washer 411 External deflector

4850 en - 2018.11 / f
Moteurs Leroy-Somer
Headquarter: Boulevard Marcellin Leroy - CS 10015
16915 ANGOULÊME Cedex 9
Limited company with capital of 65,800,512 €

RCS Angoulême 338 567 258
www.leroy-somer.com

Leroy Motor 4850f - en PDF

Uploaded by

Copyright:

Available Formats

Leroy Motor 4850f - en PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Leroy Motor 4850f - en PDF

Uploaded by

Copyright:

Available Formats

Installation & maintenance

Part number: 4850 en - 2018.11 / f

Particular attention should be given to equipotential ground or earthing connections.

2 Installation and maintenance - Three-phase induction motors

You have just acquired a LEROY-SOMER motor.

Installation and maintenance - Three-phase induction motors 3

6 - CORRECTIVE MAINTENANCE: GENERAL....... 22 Earth terminal......................................................................15

11 - FLS/FLSES MOTORS........................................ 36 Shields.......................................................................... 16 - 20

4 Installation and maintenance - Three-phase induction motors

* Other logos may be used as an optional extra:

Definition of symbols used on nameplates:

MOT 3 ~ : 3-phase A.C. motor IP55 IK08 : Index of protection Bearings

Please quote when

Installation and maintenance - Three-phase induction motors 5

1.2 - Storage 2.1 - Checking the insulation

Greases used by LEROY-SOMER

Warning: If the high voltage test, carried out at

6 Installation and maintenance - Three-phase induction motors

thermal equilibrium of the motor whatever the direction of

When the motor is fitted with lifting rings, they are

The motor must be installed in an adequately ventilated area,

Installation and maintenance - Three-phase induction motors 7

If a motor is started up without a coupling device

8 Installation and maintenance - Three-phase induction motors

To perfect this adjustment and at the same time check the

60 1.5 - Smooth pulley on the outside of the belt

Aligning the pulleys

Installation and maintenance - Three-phase induction motors 9

Optional: Standard slide rails (conforming to standard NFC 51-105)

Motor Type Dimensions Weight per pair

2.4 - Electrical guidelines The five essential modes are:

10 Installation and maintenance - Three-phase induction motors

Forced ventilation Natural cooling Forced ventilation

Before any work is carried out on the motor or in

Installation and maintenance - Three-phase induction motors 11

Operating Operating Breaking Mounting

Thermocouples V Mounted on control

- NRT: nominal running temperature.

Warning: Check that the space heaters are

12 Installation and maintenance - Three-phase induction motors

NB: motors are fitted with plugs or a support plate as standard.

Tightening capacity of cable glands

Ø min. - Ø max. (mm) cable

diameter of the cable being used.

In order to preserve the motor’s ISO M16 5 - 10 5.5 - 9.5

Installation and maintenance - Three-phase induction motors 13

Length in m Maximum voltage drop 3 % (3-phase circuits - copper cable)

2.5.3 - Connection of the motor-drive unit

14 Installation and maintenance - Three-phase induction motors

Particular attention must be paid to the

2.5.5 - Direction of rotation

If using cables without connectors, attach some calipers.

As a general rule, check that no nut, washer or

2.5.6 - Earth terminal

It is compulsory to earth the motor. Earthing

* If required, this diagram should be obtained from the supplier,

Installation and maintenance - Three-phase induction motors 15

PERMANENTLY GREASED BEARINGS

Types of permanently Grease life according to speed of rotation

Accelerometer For measuring vibrations