Gas Detection and

VESDA ECO™ Detector Environmental Monitoring

Gas Detection for Use with Features

Aspirated Smoke Detection • Toxic, Oxygen or Flammable gas
Xtralis the manufacturer of the detection
market leading VESDA aspirating • Single or dual gas versions
smoke detection (ASD) technology • Factory calibrated sensor cartridges
has developed the industries first • Integral alarm status LEDs
multi-hole aspirated gas detector.
• Integrates with PLCs/HVAC/BMS/
When used with the compatible FACP
range of ASD products; VESDA • Configurable relays
ECO provides the industries first • 4-20 mA analog outputs
combined aspirated smoke and gas
• RS485 Modbus output
detection system.
• On-board event logging
VESDA ECO provides early warning of toxic, • On-board fault diagnostics
oxygen and flammable gas hazards to protect • Integral gas test port
personnel and property whilst ensuring business
continuity. • Remote reset

Applications include: Compatibility

• Battery charging rooms • VESDA ASD
• Boiler plant rooms • ICAM ASD
• FAAST ASD
• Commercial kitchens
• Parking garages Approvals
• Utility / service tunnels • CE
• Refrigerated stores and plant rooms Electrical safety
• Water treatment and sewerage plants -- Conforms to ANSI/UL Std 61010-1
• Power generation plants -- Certified to CAN/CSA Std C22.2
No. 61010-1
• Metal processing plants
-- EN 61010-1
• and more.
• EMC
How It Works -- FCC 47CFR Part 15B class B
VESDA ECO uses an existing or new aspirating pipe network to actively -- ICES 003
monitor for gas escapes and build-ups. -- EN 50270
Each ECO gas detector can house up to two gas sensors, and additional • Others
detectors can be added easily to the pipe network to monitor more gases if -- LCPB, VdS, AFNOR compatible for
required. Pre-calibrated sensor cartridges are easily replaced in the field and use with EN54-20 approved ASD
make converting to different gas sensors or replacing sensors a simple task. -- LOM approved to UNE 23300
The VESDA ECO detector is configured using Xtralis VSC configuration (CO & CO+NO2)
software and can be remotely monitored using Xtralis VSM4 monitoring -- AQISQ – CMC Pattern Approval
software. Both VSC and VSM can be used to download data from the -- CCCF – CFE, GB:15322.1
on-board memory card for data analysis and trending of historical data. -- VNIIPO
Integration with other building systems, including fire alarm control panels, • SIL Rating
PLCs, HVAC and building management systems, provides real-time -- SIL 2 as per IEC 61508 (combustible
situational awareness for intelligent emergency response. gas and CO2 versions)
VESDA ECO by Xtralis provides significant installation and routine -- SIL 1 as per IEC 61508 (toxic gas
maintenance cost savings over conventional multi-point gas detection and oxygen versions)
solutions, by reducing the number of detectors required to cover an area and
by providing easy access for routine maintenance.
Hazardous area certified variants of VESDA ECO are available. For more Note: Consult with Xtralis if the application requires removal of
interferent gases.
information on VESDA ECO Ex, refer to document 19826.
 Gas Detection and
VESDA ECO™ Detector Environmental Monitoring

VESDA ECO Ordering information

VESDA ECO gas detectors come complete with the main housing, sensor
cartridge, data storage card and USB interface cable. Two variants are
available based on detector outputs:
Part number structure: ECO-D-B-AA-BB
Single Gas Units
Replace AA with the relevant gas type number below and remove BB:
11 Hydrogen (H2) 0-100% LFL
12 Methane (CH4) 0-100% LFL
13 Propane (C3H8) 0-100% LFL
14 Hydrogen (H2) 0-2000 ppm
15 Gasoline Vapour 0-100% LFL Specifications
16 Pentane (C5H12) 0-100% LFL
Supply Voltage
20 Alcohols 0-100% LFL
31 Oxygen depletion only (O2) 0-25% v/v 18-30 VDC
32 Oxygen depletion and enrichment (O2) 0-25% v/v Power Consumption @ 24 VDC
41 Carbon Monoxide (CO) 0-500 ppm 3.6 W (max)
43 Hydrogen Sulphide (H2S) 0-100 ppm Current Consumption
44 Sulphur Dioxide (SO2) 0-10 ppm
Typically 60 mA @ 24 V DC for a dual gas
45 Nitrogen Dioxide (NO2) 0-10 ppm (flammable / toxic) quiescent. 85 mA when in
49 Carbon Dioxide (CO2) 0-5% v/v alarm.
Dual Gas Units Dimensions (WHD)
Select one of the available combinations below. Replacing AA and BB with the 34 mm x 125 mm x 110 mm
preferred combination. Other combinations are available upon request: (1.3” x 4.9” x 4.4”)
Weight
12 – 31 Methane and Oxygen
250 g (0.6 pounds)
12 – 41 Methane and Carbon Monoxide
12 – 43 Methane and Hydrogen Sulphide IP/NEMA ratings
13 – 31 Propane and Oxygen IP65 and NEMA 4
31 – 41 Oxygen and Carbon Monoxide Operating Conditions
41 – 43 Carbon Monoxide and Hydrogen Sulphide
Temperature typically -20ºC to 50ºC
41 – 45 Carbon Monoxide and Nitrogen Dioxide (-4ºF to 122ºF) gas dependant.
Example: ECO-D-B-12-41 O2 - 20ºC to 55ºC (-4ºF to 131ºF)
NH3 -20ºC to 40ºC (-4ºF to 104ºF)
An ECO detector with relay, analogue and serial outputs for Methane and Humidity: 10-95% RH, non-condensing
Carbon Monoxide. Pipe Size
Replacement sensor cartridge part number structure: ECO-SC-AA-BB External Diameter 25 mm (EU), ¾” (US/CAN)
Where SC = Sensor Cartridge, AA-BB are 1st and 2nd gas types (see above). Wire/Terminal size
1.5 mm2 16 AWG maximum
Installation Cable Access and Termination
VESDA ECO is designed to press fit on to the air sampling pipe. To fit VESDA 2 x PG9 cable glands, to suit 4.0 to 8.5 mm
ECO simply remove a 60 mm section of pipe when using 25 mm OD air- (0.157” to 0.335”) outer cable diameter
sampling pipe work or 4” for ¾” BSP pipe. Use ECO-FT15 adapter when fitting Accuracy
ECO to 6mm based sampling systems.
+/- 5%
VESDA ECO provides total flexibility to install one or more detectors anywhere Outputs
on the pipe network to enable monitoring of a specific point, zone or total area.
4 wire RS 485 Modbus RTU
(2 wire data comms + 2 wire power)
Four (4) programmable relays 30 VDC 1A
One (1) 4-20 mA output per sensor
Onboard Memory Card
Micro SD card 2 GB - 8 GB (50,000+ events)

www.xtralis.com
UK and Europe +44 1442 242 330 D-A-CH +49 431 23284 1 The Americas +1 781 740 2223
Middle East +962 6 588 5622 Asia +86 21 5240 0077 Australia and New Zealand +61 3 9936 7000
The contents of this document are provided on an “as is” basis. No representation or warranty (either express or implied) is made as to the completeness,
accuracy or reliability of the contents of this document. The manufacturer reserves the right to change designs or specifications without obligation
and without further notice. Except as otherwise provided, all warranties, express or implied, including without limitation any implied warranties of
merchantability and fitness for a particular purpose are expressly excluded.
Xtralis, the Xtralis logo, The Sooner You Know, VESDA-E, VESDA, ICAM, ECO, OSID, HeiTel, ADPRO, IntrusionTrace, LoiterTrace, ClientTrace,
SmokeTrace, XOa, XOh, iTrace, iCommand, iRespond, iCommission, iPIR, and FMST are trademarks and/or registered trademarks of Xtralis and/or its
subsidiaries in the United States and/or other countries. Other brand names mentioned herein are for identification purposes only and may be trademarks
of their respective holder(s). Your use of this document does not constitute or create a licence or any other right to use the name and/or trademark and/
or label.
This document is subject to copyright owned by Xtralis. You agree not to copy, communicate to the public, adapt, distribute, transfer, sell, modify or
publish any contents of this document without the express prior written consent of Xtralis.
Doc. 18424_14
 Gas Detector for
VESDA ECO™ Ex Gas Detector Hazardous Locations

Gas Detection for Use with Aspirating Features

Smoke Detection • Approved for Class I Div 2
Xtralis the manufacturer of the market leading applications
VESDA aspirating smoke detection (ASD) • Toxic, Oxygen or Flammable gas
technology has developed the industries first detection
multi-hole aspirated gas detector. • Single or dual gas versions
When used with the compatible range of ASD • Factory calibrated sensor cartridges
products; VESDA ECO (Ex) provides the industries • Integral alarm status LEDs
first combined aspirated smoke and gas detection
system. • Integrates with PLCs/HVAC/BMS/
FACP
VESDA ECO (Ex) provides early warning of toxic, • Configurable relays
oxygen and flammable gas hazards to protect
• 4-20 mA analog outputs
personnel and property whilst ensuring business
continuity. • RS485 Modbus output
• On-board event logging
VESDA ECO (Ex) is approved for use within
Class I Division 2 classified hazardous locations. • On-board fault diagnostics
It must be used with a similarly approved VESDA • Integral gas test port
ASD and installed within the Class I Div 2 area. • Remote reset
Applications include:
Compatibility
• Battery charging rooms • VESDA ASD
• Boiler plant rooms • ICAM ASD
• Utility/ service tunnels • FAAST ASD
• Refrigerated stores and plant rooms
• Water treatment and sewerage plants Approvals
• Power generation plants • Electrical safety
• Metal processing plants -- Conforms to ANSI/UL Std 61010-1
• and more. -- Certified to CAN/CSA Std C22.2
No. 61010-1
How It Works -- EN 61010-1
VESDA ECO (Ex) uses an existing or new aspirating pipe network to actively • EMC
monitor for gas escapes and build-ups. -- FCC 47CFR Part 15B class B
Each VESDA ECO (Ex) gas detector can house up to two gas sensors, and -- ICES 003
additional detectors can be added easily to the pipe network to monitor more -- EN 50270
gases if required. Pre-calibrated sensor cartridges are easily replaced in the • Hazardous Location
field and make converting to different gas sensors or replacing sensors a -- ETL approved to ISA12.12.01,
simple task. CSA C22.2 No. 213
The VESDA ECO (Ex) detector is configured using Xtralis VSC configuration -- Class I Div 2 Groups ABC&D T4
software and can be remotely monitored using Xtralis VSM4 monitoring -4ºF ≤ Tamb ≤ +131ºF
software. Both VSC and VSM can be used to download data from the • SIL Rating
on-board memory card for data analysis and trending of historical data. -- SIL 2 as per IEC 61508 (combustible
Integration with other building systems, including fire alarm control panels, gas and CO2 versions)
PLCs, HVAC and building management systems, provides real-time -- SIL 1 as per IEC 61508 (toxic gas and
situational awareness for intelligent emergency response. oxygen version)

VESDA ECO (Ex) by Xtralis provides significant installation and routine

maintenance cost savings over conventional multi-point gas detection Note: Consult with Xtralis if the application requires removal of
solutions, by reducing the number of detectors required to cover an area and interferent gases.
by providing easy access for routine maintenance.
 Gas Detector for
VESDA ECO™ Ex Gas Detector Hazardous Locations

VESDA ECO (Ex) Ordering information Specifications

VESDA ECO (Ex) gas detectors are supplied complete with: Outer metal Supply Voltage
casing and surface mounting assembly, detector housing, sensor cartridge, 18-30 VDC
data storage card and USB interface cable. Detector outputs include: relays,
Power Consumption @ 24 VDC
analogue outputs and a serial output.
3.6 W (max)
Single Gas Units
Current Consumption
Part number structure: ECO-D-B-AA-Ex Typically 60 mA @ 24 VDC per sensor (Gas
and quantity dependant)
Replace AA with the relevant gas type number below:
Dimensions (protective enclosure)
11 Hydrogen (H2) 0-100% LFL
155 mm x 135 mm x 74 mm
12 Methane (CH4) 0-100% LFL (6.1” x 5.3” x 2.9”)
13 Propane (C3H8) 0-100% LFL Material
14 Hydrogen (H2) 0-2000 ppm
Enclosure 304 Stainless Steel, Detector
15 Gasoline Vapour 0-100% LFL PC/ABS
16 Pentane (C5H12) 0-100% LFL Weight
20 Alcohols 0-100% LFL 1 kg (2.2 lb) detector and enclosure
31 Oxygen depletion only (O2) 0-25% v/v combined
32 Oxygen depletion and enrichment (O2) 0-25% v/v IP/NEMA ratings
41 Carbon Monoxide (CO) 0-500 ppm IP54 (minimum)
43 Hydrogen Sulphide (H2S) 0-100 ppm Operating Conditions
44 Sulphur Dioxide (SO2) 0-10 ppm Temperature typically -20ºC to 50ºC
45 Nitrogen Dioxide (NO2) 0-10 ppm (-4ºF to 122ºF) gas dependant.
49 Carbon Dioxide (CO2) 0-5% v/v O2 - 20ºC to 55ºC (-4ºF to 131ºF)
NH3 -20ºC to 40ºC (-4ºF to 104ºF)
Dual Gas Unit Humidity: 10-95% RH, non-condensing
Part number structure: ECO-B-AA-BB-Ex Accuracy

12 – 43 Methane and Hydrogen Sulphide Typically +/- 5%

Sample Pipe Size
Replacement sensor cartridge part number structure: ECO-SC-AA-BB-Ex
External Diameter 25 mm (EU), ¾”
Where SC = Sensor Cartridge, AA-BB are 1st and 2nd gas types (see above) (US/CAN)
Cable Access
Installation 2 x PG9 cable glands, to suit 4.0 to 8.5 mm
(0.157” to 0.335”) outer cable diameter
VESDA ECO (Ex) is designed to press fit on to the air sampling pipe. To fit
VESDA ECO (Ex) simply remove a 60 mm section of pipe when using 25 mm Wire/Terminal size
OD air-sampling pipe work or 4” for ¾” BSP pipe. Use ECO-FT15 adapter 1.5 mm2 16 AWG maximum
when fitting ECO to 6mm based sampling systems. Outputs

VESDA ECO (Ex) provides total flexibility to install one or more detectors Four (4) programmable relays 30 VDC 1A
Two 4-20 mA outputs, one per gas sensor
anywhere on the pipe network to enable monitoring of a specific point, zone or and 2 wire RS 485 Modbus RTU
total area.
Onboard Memory Card
Micro SD card 2 GB - 8 GB
(50,000+ events)

www.xtralis.com
UK and Europe +44 1442 242 330 D-A-CH +49 431 23284 1 The Americas +1 781 740 2223
Middle East +962 6 588 5622 Asia +86 21 5240 0077 Australia and New Zealand +61 3 9936 7000
The contents of this document are provided on an “as is” basis. No representation or warranty (either express or implied) is made as to the completeness,
accuracy or reliability of the contents of this document. The manufacturer reserves the right to change designs or specifications without obligation
and without further notice. Except as otherwise provided, all warranties, express or implied, including without limitation any implied warranties of
merchantability and fitness for a particular purpose are expressly excluded.
Xtralis, the Xtralis logo, The Sooner You Know, VESDA-E, VESDA, ICAM, ECO, OSID, HeiTel, ADPRO, IntrusionTrace, LoiterTrace, ClientTrace,
SmokeTrace, XOa, XOh, iTrace, iCommand, iRespond, iCommission, iPIR, and FMST are trademarks and/or registered trademarks of Xtralis and/or its
subsidiaries in the United States and/or other countries. Other brand names mentioned herein are for identification purposes only and may be trademarks
of their respective holder(s). Your use of this document does not constitute or create a licence or any other right to use the name and/or trademark and/
or label.
This document is subject to copyright owned by Xtralis. You agree not to copy, communicate to the public, adapt, distribute, transfer, sell, modify or
publish any contents of this document without the express prior written consent of Xtralis.
Doc. 19826_08
 ® ®
VESDA VLI by Xtralis VLI-880, VLI-885
Features
• Suitable for Class 1 Division 2 applications
- Groups A,B,C & D
• Up to 2000 m2 (21,520 sq. ft.) coverage
• Up to 4 inlet pipes
• Total pipe length up to 360 m (1181 ft)
• Five (5) high intensity status LEDs for
greater visibility
• Robust absolute smoke detection
• Intelligent Filter (patent pending)
• Lint Trap to capture fibrous particulates
• Sub-sampling Probe (inertial separator)
• Secondary Filter
The VESDA VLI by Xtralis is an industry first early warning aspirating smoke • Clean air barrier for optics protection
detection (ASD) system, designed to protect industrial applications and harsh • Referencing
environments of up to 2000 m2 (21,520 sq. ft.). • AutoLearn™ Smoke and Flow
• Clean Air Zero™
Long life, intelligent, fail-safe technology • Air-path monitoring
• Five (5) relays (Fire, Fault and 3
The VLI detector combines a fail-safe Intelligent Filter (patent pending) configurable)
with an advanced clean-air barrier for optics protection allowing the use of • Relays configurable as latching or non-
absolute detection and a long detection chamber life without the need for re- latching
calibration. • Expandable GPI and relays
• Ultrasonic flow sensing
The Intelligent Filter:
• Xtralis VSC, Xtralis VSM4 and ASPIRE
• reduces the level of pollution in the air sample before it enters the detection software support
chamber, which dramatically extends the operational life of the detector in • IP66 Enclosure
harsh and polluted environments. • Easy mounting with steel support bracket
• Modular field replaceable parts for ease
• is fully monitored, providing consistent sensitivity over the entire
of servicing
operational life of the detector.
• Local USB configuration port
Installation, Commissioning and Operation • Easy cable termination access
• Imperial and metric pipe ports
The VLI detector features a robust IP66-rated enclosure which provides • Rubberized finish to external housing
complete protection against dust ingress and strong water jets from all
directions. In the majority of industrial applications, specifically in very Listings / Approvals
harsh environments, this eliminates the need to use expensive external IP
enclosures, thus simplifying and reducing the cost of installation. • UL
• ULC
The VLI detector is equipped with a powerful aspirator that provides a total • FM
pipe length of 360 m (1181 ft). It is fully supported by the Xtralis ASPIRE, • ActivFire
VSC and VSM4 software applications which facilitate ease of pipe network • CE
design, system commissioning and maintenance together with compatibility • LPCB
with existing VESDA installations. • NF
The AutoLearn™ commissioning assistant reduces setup time and ensures • SIL 2 as per IEC 61508
optimum alarm and flow thresholds in a range of environments. • EN 54-20
-- Class A (24 holes / Alert = 0.06% obs/m)
The VLI detector is inherently less prone to nuisance alarms due to the -- Class B (28 holes / Fire-1 = 0.15% obs/m)
intelligent filter, lint trap, sub-sampling probe and secondary filter. Coupled -- Class C (60 holes / Fire-1 = 0.15% obs/m)
with its modular design, VLI offers a lower total cost of ownership over the life Classification of any configuration is determined using
of the product. ASPIRE.
Regional approvals listings and regulatory compliance vary between
VESDA product models. Refer to www.xtralis.com for the latest product
approvals matrix.
 ® ®
VESDA VLI by Xtralis VLI-880, VLI-885

How it works Specification

Air is continually drawn through the pipe network and into the VLI detector by Supply voltage:
18 to 30 VDC
a high efficiency aspirator. The air sample passes four (4) sets of ultrasonic
Power consumption:
flow sensors before being passed through the Intelligent Filter. The Intelligent 10 W quiescent, 10.5 W with alarm (max)
Filter incorporates an innovative flow splitting arrangement where a smaller
Current consumption:
unfiltered portion is passed through another set of ultrasonic flow sensors and 415 mA quiescent, 440 mA with alarm (max)
a larger portion of the sample passes through a HEPA filtration medium. This Fuse rating:
arrangement dramatically reduces the amount of contaminants entering the 1.6 A
aspirator and the detection chamber, thus extending detector life. Dimensions (WHD):
426.5 mm x 316.5 mm x 180 mm
Filter loading is constantly monitored which enables the detector to (16.8 in x 12.5 in x 7.1 in)
“intelligently” maintain the sensitivity, hence ensuring consistent and reliable Weight:
operation over time. This is achieved by comparing the readings from the 6.035 kg (13.3 lbs)
four (4) sets of ultrasonic flow sensors at the detector air inlets to the readings Operating conditions:
from that in the unfiltered path and measuring the split of the airflow ratio as Tested to -10°C to 55°C (14°F to 131°F)
Recommended Detector Ambient: 0°C to 39°C
the filter load changes.
Sampled Air: -20°C to 60°C (-4°F to 140°F)
The filtered and unfiltered portions are recombined as they exit the Intelligent Humidity: 10% to 95% RH, non-condensing
Filter. A portion of the recombined air sample is then passed through the Sampling network:
Maximum area of Coverage 2000 m2 (21,520 sq.ft)
sub-sampling probe (inertial separator) and secondary filter. This ensures Minimum total airflow: 40 l/m
that larger dust particles are less likely to pass through the probe and Minimum airflow per pipe: 20 l/m
filter arrangement, hence they are exhausted out of the detector. This Maximum pipe lengths:
configuration minimizes nuisance alarms caused by larger dust particles and Total Pipe Length: 360 m (1181 ft)
extends detection chamber life. A third filter within the detection chamber Maximum Single Pipe Length: 120 m (394 ft)
assembly delivers a clean air barrier which protects the optical surfaces Computer design tool:
ASPIRE
from contamination, further extending detector life and ensuring absolute
calibration. Pipe:
Internal Diameter 15 mm - 21 mm (9/16”–7/8”)
The detection chamber uses a stable, highly efficient laser light source and External Diameter 25 mm (1”)
unique sensor configuration to achieve optimum response to a wide range of Relays:
5 Relays rated 2 A @ 30 VDC
smoke types. The presence of smoke in the detection chamber creates light Fire (NO), Fault (NC), Configurable (NO)
scattering which is detected by the very sensitive sensor circuitry and then
IP rating:
converted to an alarm signal. IP66
The status of the detector, all alarms, service and fault events, are monitored Cable access:
4 x 25 mm (1”) cable entries
and logged with time and date stamps. Status reporting can be transmitted via
relay outputs and across VESDAnet (VN version only). Cable termination:
Screw Terminal blocks 0.2–2.5 sq mm (30–12 AWG)

Clean Air Zero Sensitivity Range:

0.005% - 20.0% obs/m (0.0015% - 6.25% obs/ft)
Clean Air Zero is a user-initiated VLI feature which compliments consistent Threshold setting range:
absolute detection over time and also safeguards against nuisance alarms. Alert: 0.05%-1.990% obs/m (0.016%-0.6218% obs/ft)
Action: 0.1%-1.995% obs/m (0.031%-0.6234% obs/ft)
This is achieved by introducing clean air into the detection chamber and Fire1: 0.15 %-2.0% obs/m (0.047% - 0.625% obs/ft)
taking a reference reading of the chamber background. This reading is then Fire2: 0.155 % - 20.0% obs/m (0.05% - 6.25% obs/ft)*
*Limited to 4% obs/ft for UL
offset against the actual environmental background to maintain consistent
Software features:
absolute smoke detection. Event log: Up to 18,000 events stored in FIFO format
Smoke level, user actions, alarms and faults with time
Ordering Information Spare Parts and date stamp
VESDA VLI VLI-880 VLI Intelligent Filter VSP-030 AutoLearn: Min 15 minutes, Max 15 days.
VESDA VLI with VESDAnet1 VLI-885 VLI Secondary Foam Filter VSP-031
Recommended minimum 14 days.
While AutoLearn is in progress, thresholds are NOT
VESDA VLI Remote Display 7 Relays VRT-Q00 VLI Aspirator VSP-032
changed from pre-set values.
VESDA VLI Remote Display No Relays VRT-T00 VLI Chamber Assembly VSP-033
VLI VESDAnet Card VSP-034 Configurable general input (5 - 30 VDC):
VLI Remote Display Module Spare VSP-035 External Reset, Mains OK, Standby, Isolate, Use
Notes:
VLI Ultrasonic Flow Manifold Spare VSP-036
Night-time Threshold, Reset + Isolate, Inverted Reset
1. Please contact your nearest Xtralis office for availability.

www.xtralis.com
UK and Europe +44 1442 242 330 D-A-CH +49 431 23284 1 The Americas +1 781 740 2223
Middle East +962 6 588 5622 Asia +86 21 5240 0077 Australia and New Zealand +61 3 9936 7000
The contents of this document are provided on an “as is” basis. No representation or warranty (either express or implied) is made as to the completeness,
accuracy or reliability of the contents of this document. The manufacturer reserves the right to change designs or specifications without obligation
and without further notice. Except as otherwise provided, all warranties, express or implied, including without limitation any implied warranties of
merchantability and fitness for a particular purpose are expressly excluded.
Xtralis, the Xtralis logo, The Sooner You Know, VESDA-E, VESDA, ICAM, ECO, OSID, HeiTel, ADPRO, IntrusionTrace, LoiterTrace, ClientTrace,
SmokeTrace, XOa, XOh, iTrace, iCommand, iRespond, iCommission, iPIR, and FMST are trademarks and/or registered trademarks of Xtralis and/or its
subsidiaries in the United States and/or other countries. Other brand names mentioned herein are for identification purposes only and may be trademarks
of their respective holder(s). Your use of this document does not constitute or create a licence or any other right to use the name and/or trademark and/
or label.
This document is subject to copyright owned by Xtralis. You agree not to copy, communicate to the public, adapt, distribute, transfer, sell, modify or
publish any contents of this document without the express prior written consent of Xtralis.
Doc. no. 17115_19 Part: 29414
VESDA-E VEA VEA-040-A00, VEA-040-A10
Features
• Pinpoint addressability with superior
detection compared to spot detectors
• 40 addressable microbore tubes with
individual sampling points
• Assured detection with end to end system
integrity monitoring
• Interruption-free business operation with
centralised testing and maintenance
• Single sampling point or single tube
blockage detection
The VESDA-E VEA series of detectors combine VESDA reliability and • Automatic sampling point presence and
early warning smoke detection with pinpoint addressability and a variety of tube breakage detection
annunciation options that truly surpass traditional spot detectors. They use • Automatic sampling point cleaning
patented air sampling points and multi-channel microbore air-sampling with • Three sensitivity settings for the sampling
three alarm sensitivity settings for the sampling points. As a multi-channel points
addressable system, the VEA detector is able to divide a protected space • Variable length capillary tubes, up to 100 m
into sampling locations, enabling the localization of potential sources of (330 ft)
fire for faster incident response. The detectors are suitable for protection • Laser-based absolute smoke detection
of areas where pinpoint location of fire events is essential, thus providing • Dual stage filtering and clean air barrier for
ideal fire detection solutions for healthcare, offices, education, retail, prisons optics protection
and electrical cabinets. A wide range of features provide flexibility, field • Reliable linear pump technology
programmability, enhanced connectivity and reduced total cost of ownership. • LEDs for alarm and fault signalling
• 3.5” colour touch screen for status review
Installation, Commissioning and Maintenance
• Seven programmable relays
The VEA detector features a robust IP40-rated enclosure and is equipped • Two GPIs, monitored and unmonitored
with a powerful pump that provides up to 100 m (330 ft) microbore tube
• Xtralis VSC and VSM4 PC software
length. It is fully supported by the Xtralis VSC software which facilitates ease support
of system commissioning and maintenance. During commissioning, the
• iVESDA application for system monitoring
normalization process establishes the flow performance parameters. Local on mobile devices
smoke test ports are used during servicing to verify that the system is fully • IP 40 enclosure (not UL tested)
operational. Field replaceable filter, smoke sensor module, pump and rotary
• Easy mounting with steel support bracket
valve components result in less down time and ease of maintenance.
• Field replaceable filter, smoke sensor
Color LCD display module, pump and rotary valve
The VEU-040-A10 detector features a 3.5” colour LCD display which provides • VESDAnet networking
a range of status information including alarm and fault conditions as well • Ethernet 100 base T
as smoke level. Screens for each type of information are available using a • WiFi, 802.11 b/g/n
simple navigation system. • Local host-mode USB port
VESDAnet™ • Easy cable termination access
• Event Log (20,000 events)
VESDA detectors and devices communicate on VESDAnet which provides
a robust bi-directional communication network allowing continued redundant Listings / Approvals
operation even during single point wiring failures. VESDAnet enables primary
reporting, centralized configuration, control, maintenance and monitoring. • UL
• ULC
Ethernet and WiFi connectivity
• Other major agency approvals pending
VESDA-E detectors offer Ethernet and WiFi connectivity as standard
features. The detector can be added to a corporate network, allowing Regional approvals listings and regulatory compliance vary between
product models. Refer to www.xtralis.com for the latest product approvals
WiFi enabled tablet devices and laptops installed with Xtralis configuration matrix.

software to connect wirelessly to the detector via the network.

VESDA-E VEA VEA-040-A00, VEA-040-A10
Specifications How it works
Supply Voltage: 18 to 30 VDC The VEA detector draws a combined
Power Consumption @ 24VDC: VEA-040-A00 VEA-040-A10 air sample from a network of
Quiescent 22 W 23 W microbore flexible tubing from all
Alarm Average 35.5 W 36.5 W sampling points in the protected area,
Peak current (scan mode) 3.5A (for initial 5 seconds of scanning) then filters and analyzes the sample
Aspirator Linear Vacuum Pump in laser detection chambers in the
Dimensions (WHD): 352 mm x 336 mm x 135.5 mm (13.9in x 13.2in x 5.33in) smoke sensor module. When smoke
Weight: VEA-040-A00: 9.9 kg (21.8 lbs) particles are detected and the smoke
VEA-040-A10: 10 kg (22.2 lbs) level reaches set alarm thresholds,
Operating Conditions: Ambient: 0°C to 39°C (32°F to 102°F)
the system will raise appropriate
Sampled Air: 0°C to 50°C (32°F to 122°F) alarm conditions. After a Fire 1 alarm
Tested to: 0°C to 49°C (32°F to 120°F)* is raised, the system will sequentially
Humidity: 10% to 95% RH, non-condensing scan the sampling locations via the
Microbore Tube Size: OD: 6 mm, ID 4 mm rotary valve to identify one or more
OD: 4 mm, ID 2.5 mm sampling locations with the fire alarm
Microbore Tube Length: Up to 100m (330 ft) event. To assist in investigation of the
Flow Monitoring: Single sampling point and single tube blockage and breakage source of a fire, if the system is in Pre-
detection Alarm, the user can initiate a smoke
Relays: 7 programmable relays (latch or non-latch states) scan of all sampling locations.
Contacts rated 2 A @ 30 VDC (Resistive)
IP Rating: IP40 The VEA uses a vacuum pump
Cable Access: 4 x 25 mm (1”) cable entries which provides superior detection
Cable Termination: Screw Terminal blocks 0.2–2.5 sq mm (24 - 14 AWG) times for long tube lengths. The
Pre-alarms: Alert and Action - two pre alarm levels system monitors the airflow within
Sensitivity: 0.020%/m (0.006%/ft) - 16%/m (4.88%/ft)
the installation, allowing detection of
Fire-1 Alarm Thresholds High: 1.6 %/m (0.5 %/ft)
breakages or blockages of individual
at the Sampling Hole: Enhanced 4.0 %/m (1.3 %/ft)
sampling points and sampling tubes,
with faults indicated on the display and
Standard 8.0 %/m (2.5 %/ft)
to the monitoring equipment.
Communication Interfaces: USB (Type 2), Ethernet (RJ45), WiFi (802.11 b/g/n)
Software Features: Event log: Up to 20,000 events stored in FIFO format, smoke Alarms and fire location can be
level, user actions, alarms and faults with time and date stamp signaled via Relays and VESDAnet.
Ethernet and WiFi can be used
for configuration and secondary
monitoring, and a USB interface is
provided for field installation and
maintenance. The optional Relay StaX
module can be used to identify and
signal fire source locations on a fire
panel loop.
A series of LEDs display Alarm,
* Product UL Listed between 0°C to 39°C (32°F to 102°F)
Trouble, Disable and detector power
Ordering Information Spare Parts on status. A button allows the user
VESDA-E VEA-40 Aspirating Smoke VEA-040-A00 VESDA-E VEA-40 Mounting Bracket VSP-970 to Reset or Disable the detector.
Detector with LEDs
VESDA-E VEA-40 Aspirating Smoke VEA-040-A10
VESDA-E VEA-40 Smoke Sensor Module VSP-971
Additionally, the VEA-A10 features
VESDA-E VEA Filter VSP-972
Detector with 3.5” Display a 3.5” LCD display which shows
VESDA-E VEA Pump VSP-973
VESDA-E VEA-20 Expansion StaX VEA-020-STX
VESDA-E VEA Rotary Valve VSP-974
detector status.
VESDA-E VEA-40 Expansion StaX VEA-040-STX
VESDA-E VEA 40-Relay Local StaX VER-A40-40-STX
VESDA-E VEA-040-A00 Fascia with LEDs VSP-975 Expansion to 60, 80, 100 or 120
VESDA-E VEA-040-A10 Fascia with 3.5” Display VSP-976
Sampling Point for 6mm Tube VSP-980 sampling points can be achieved by
Sampling Point for 6mm Tube (22 pack) VSP-980-22 installing additional Expansion StaX
Sampling Point for 6mm Tube (44 pack) VSP-980-44
modules.
Sampling Point for 4mm Tube VSP-981
Sampling Point for 4mm Tube (22 pack) VSP-981-22 Approvals Compliance
Sampling Point for 4mm Tube (44 pack) VSP-981-44 Please refer to the Product Guide for details regarding compliant design,
installation and commissioning.

www.xtralis.com
UK and Europe +44 1442 242 330 D-A-CH +49 431 23284 1 The Americas +1 781 740 2223
Middle East +962 6 588 5622 Asia +86 21 5240 0077 Australia and New Zealand +61 3 9936 7000
The contents of this document are provided on an “as is” basis. No representation or warranty (either express or implied) is made as to the
completeness, accuracy or reliability of the contents of this document. The manufacturer reserves the right to change designs or specifications
without obligation and without further notice. Except as otherwise provided, all warranties, express or implied, including without limitation any
implied warranties of merchantability and fitness for a particular purpose are expressly excluded.
Xtralis, the Xtralis logo, The Sooner You Know, VESDA-E, VESDA, ICAM, ECO, OSID, HeiTel, ADPRO, IntrusionTrace, LoiterTrace, ClientTrace,
SmokeTrace, XOa, XOh, iTrace, iCommand, iRespond, iCommission, iPIR, and FMST are trademarks and/or registered trademarks of Xtralis and/or its
subsidiaries in the United States and/or other countries. Other brand names mentioned herein are for identification purposes only and may be trademarks
of their respective holder(s). Your use of this document does not constitute or create a licence or any other right to use the name and/or trademark and/
or label.
This document is subject to copyright owned by Xtralis. You agree not to copy, communicate to the public, adapt, distribute, transfer, sell, modify or
publish any contents of this document without the express prior written consent of Xtralis.
Doc. no. 22210_09 Part: 30359