PWM Control 2-3A Step-Down Converter BM1513/A

FEATURES GENERAL DESCRIPTION

 Input voltage: 3.6V to 18V. BM1513/A consists of step-down switching

 Output voltage: 0.8V to VCC. regulator with PWM control. These devices
 BM1513 is 2A ; BM1513A is 3A include a reference voltage source, oscillation
 Oscillation frequency: 400KHz circuit, error amplifier, internal PMOS and etc.
 Soft-start, Current limit, Enable function
 Thermal Shutdown function BM1513/A provides low-ripple power, high efficiency
 Built-in internal SW P-channel MOS and excellent transient characteristics. The PWM
 replace AP151x series control circuit is able to very the duty ratio linearly
 SOP-8L Pb-Free Package. from 0 up to 100%. This converter also contains
an error amplifier circuit as well as a soft-start
circuit that prevent s overshoot at startup. An
enable function, an over current protect function
APPLICATIONS and a short circuit protect function are built inside,
and when OCP or SCP happens, the operation
 portable DVD frequency will be reduced from 400KHz to 60KHz.
 LCD Monitor Also, an internal compensation block is built in to
 Graphic Card minimum external component count.
 DVD-Video Player
These ICs can function as step-down switching
 Telecom Equipment
regulators. They serve as ideal power supply units
 ADSL Modem
for portable devices when coupled with the SOP-8L
 Printer and other Peripheral Equipment
mini-package, providing such outstanding features
 Microprocessor core supply
as low current consumption. Since this converter
 Networking power supply
can accommodate an input voltage of up to 18V, it
is also ideal when operating via an AC adapter.

PIN DESCRIPTIONS
Name Pin Description
PIN ASSIGNMENTS FB 1 Feedback pin.
Power-off pin
H: Normal operation
FB 1 ● 8 Vss
EN 2
(Step-down operation)
L: Step-down operation
2 7 Vss stopped
EN
(All circuits deactivated)
BM1513/A
3 Add an external resistor to set
OCSET 3 6 Output OCSET max output current.
VCC 4 IC power supply pin
VCC 4 5 Output Switch Pin. Connect external
inductor/diode here. Minimize
Output 5、6 trace area at this pin to reduce
EMI.
VSS 7、8 GND Pin

1/7

Free Datasheet http://www.datasheet4u.net/

PWM Control 2-3A Step-Down Converter BM1513
Ordering Information

BM1513 X E

acking
A: 3A ; Non-A means: 2A E means engineer, Non E means normal. Blank : Tube
A : Taping

Block Diagram

Output

Oscillation Reference Voltage

Circuit Source with Soft Start
Vcc

+
PWM-Switched
FB
Control Circuit
-
Thermal
Shutdown

VON/OFF 100uA Vss

EN OCSET

Absolute Maximum Ratings

Symbol Parameter Rating Unit
VCC*1 VCC pin voltage VSS - 0.3 to VSS + 20 V
VFB Feadback pin voltage VSS - 0.3 to VCC V
VON/OFF*1 ON/OFF pin voltage VSS - 0.3 to VIN + 0.3 V
VOUTPUT Switch pin voltage VSS - 0.3 to VIN + 0.3 V
PD Power dissipation Internally limited mW
o
TOPR Operating temperature range -20 to +125 C
o
TSTG Storage temperature range -40 to +150 C
Caution: The absolute maximum ratings are rated values exceeding which the product could suffer physical
damage. These values must therefore not be exceeded under any conditions.

2/7

Free Datasheet http://www.datasheet4u.net/

PWM Control 2-3A Step-Down Converter BM1513
Electrical Characteristics (VIN = 12V, Ta=25°C, unless otherwise specified)
Symbol Parameter Conditions Min. Typ. Max. Unit
VFB Feedback Voltage -- 0.784 0.8 0.816 V
VIN Input voltage -- 3.6 -- 18 V
ISW Switch Current (1513/A) -- 2A/ 3.0 -- -- A
ISSS Current consumption VON/OFF =0V -- 10 -- µA
during power off
∆VOUT VIN = 3.6V~18V -- 0.6 1 %
/VOUT Line regulation
∆VOUT IOUT = 0 to 2A -- 0.2 0.5 %
/VOUT Load regulation
fOSC Oscillation frequency Measure waveform at SW pin 360 400 440 KHz
fOSC1 Frequency of current limit or Measure waveform at SW pin 8 160 16 KHz
short circuit protect
VSH Evaluate oscillation at SW pin 2.0 -- --
V
VSL EN pin input voltage Evaluate oscillation stop at SW pin -- -- 0.8
ISH EN pin input leakage -- -10 -- 10 µA
ISL current -- -10 -- 10 µA
IOCSET OCSET pin bias current -- 90 100 110 µA
TSS Soft-Start time -- 0.3 2 5 ms
RDSON Internal MOSFET Rdson -- - 100 150 mΩ
EFFI Efficiency VIN = 12V, VOUT = 5V -- 92 -- %
IOUT = 2A

Typical Application Circuit

VOUT
VIN Vcc Output

RA
ROCSET COCSET CC
Optional
FB
OCSET +
BM1513 RB
COUT
CVcc D1
REN
20K

CIN EN
VSS

CEN
0.1µ

Note: VOUT = VFB x (1+RA/RB)

RB=1K~10K ohm

3/7

Free Datasheet http://www.datasheet4u.net/

PWM Control 2-3A Step-Down Converter BM1513
Typical Performance Characteristics

BM1513 Efficiency BM1513 Vin v.s. FB

(Vin=12V) (Vout=3.3V; Iout=0.5A)
0.81
96 0.805
Vout=5V
0.8
92
0.795
88 Vout=3.3V 0.79
0.785
84
Vout =3V 0.78
80 0.775
0.77
76
0.765
72 0.76
0 0.5 1 1.5 2 0 5 10 15 20
Iout (A) Vin (V)

BM1513 Vin v.s. Frequency BM1513 Load Regulation

(Vout=3.3V; Iout=0.5A) (Vin=12V)
410 3.35
400
390 3.3
440
410 3.25
380
350 3.2
340
330 3.15
320
310 3.1
0 5 10 15 20 0 0.5 1 1.5 2
Vin (V) Iout (A)

4/7

Free Datasheet http://www.datasheet4u.net/

PWM Control 2-3A Step-Down Converter BM1513
Typical Performance Characteristics (Continued)
BM1513 Vout Ripple BM1513 Vout Ripple
(Vin=12V; Vout=3.3V; Iout=0.2A) (Vin=12V; Vout=3.3V; Iout=2A)

Test Circuit
Open
Open
OUTPUT OUTPUT
VCC FB A VCC FB

OCSET
+
OCSET
A EN EN
VSS VSS

VIN C1
12v 470uF R5 OUTPUT FB 1 8
VCC FB VSS
R4 100K ON
3K OCSET 2 7
+ EN VSS
+ V
EN OFF 3 6 L 22 uH VOUT
VSS OCSET Output
4 5 3.3v
VCC Output
C3
0.1uF R1
D1 4.7K C2
B220 R2 470uF
1.5K

5/7

Free Datasheet http://www.datasheet4u.net/

 PWM Control 2-3A Step-Down Converter BM1513

PWM Control Output Voltage Definition

The BM1513/A consists of DC/DC converters that The output voltage is programmed by selection of the
employ a pulse-width modulation (PWM) system. divider R1 and R2. Designer should use resistors R1
In converters of the BM1513/A, the pulse width and R2 with ±1% tolerance in order to obtain best
varies in a range from 0 to 100, according to the accuracy of output voltage. The output voltage can
load current, and yet ripple voltage produced by be calculated from the following formula.
the switching can easily be removed through a
Vout = 0.8 x ( 1 + R1 / R2)
filter because the switching frequency remains
constant. Therefore, these converters provide a
Select a value for R2 between 0.5KΩ and 10KΩ. The
low-ripple power over broad ranges of input
lower resistor values minimize noise pickup in the
voltage and load current. sensitive feedback pin.

Under Voltage Lockout Recommended resistance value list below:

The under voltage lockout circuit of the BM1513/A
assures that the high-side MOSFET driver outputs Vo = 3.3V Vo = 5.0V
remain in the off state whenever the supply voltage R1 4.7K 6.8K
drops below set parameters. Lockout occurs if VCC R2 1.5K 1.3K
falls below 3.3V. Normal operation resumes once
VCC rises above 3.5V.
Max. Current Limiting
The current limit threshold is setting by connecting
an external resistor from VCC supply to OCSET. The
voltage drop across this resistor is due to the 100uA
internal sink sets the voltage at the pin. When the
PWM voltage is less than the voltage at OCSET, an
over-current condition occurs.
8 5
Select a value for ROCSET to set the current limit
level by using this formula:
BM1513 ILOAD = (IOCSET x ROCSET)/ RDSON
Y WW X P In which the RDSON =100 mΩ、IOCSET =100uA, if
the ROCSET =3K then the ILOAD have 3A maximum
transient current.

Note:
BM1513A is fully same as BM1513 , only bigger
current output , BM1513A can replace BM1513
without change anything in external.

6/7

Free Datasheet http://www.datasheet4u.net/

PWM Control 2-3A Step-Down Converter BM1513
Package Information
Package Type: SOP-8L

VIEW "A"

D
0.015x45
7 (4X) 7 (4X)

e B VIEW "A"
y

Dimensions In Millimeters Dimensions In Inches

Symbol
Min. Nom. Max. Min. Nom. Max.
A 1.40 1.60 1.75 0.055 0.063 0.069
A1 0.10 - 0.25 0.040 - 0.100
A2 1.30 1.45 1.50 0.051 0.057 0.059
B 0.33 0.41 0.51 0.013 0.016 0.020
C 0.19 0.20 0.25 0.0075 0.008 0.010
D 4.80 5.05 5.30 0.189 0.199 0.209
E 3.70 3.90 4.10 0.146 0.154 0.161
e - 1.27 - - 0.050 -
H 5.79 5.99 6.20 0.228 0.236 0.244
L 0.38 0.71 1.27 0.015 0.028 0.050
y - - 0.10 - - 0.004
θ 0O - 8O 0O - 8O

7/7

Free Datasheet http://www.datasheet4u.net/