Technical Data Sheet

Approved 500;501;499 1,5 500 epoxy ^(ValidationDate) 1

Jotafloor Solvent Free Primer

Product description
This is a two component amine cured solvent free epoxy coating. It is transparent. It ensures very good
adhesion on most concrete floors in atmospheric environments only. Specially designed for high build floor
coatings on properly prepared concrete floors and walls.

Typical use
Designed for a wide range of floors with various levels of mechanical and chemical exposure. It is a primer for
all Jotafloor products. Specially designed for use with the traffic deck system for heavy duty traffic, areas such
as ramps, car parks, parking bays, pedestrian walkways, roof decks and industrial floors. Recommended for cold
stores, laboratories, hospitals, food and beverage plants, kitchens, high tech manufacturing facilities, dairies,
warehouses, factories and hangars. This product when used with Jotafloor Non Slip Aggregates, is suitable for
filling and repairing of cracks, undulations and surface imperfections.
Other

Approvals and certificates

Additional certificates and approvals may be available on request.

Colours
transparent

Product data
Property Test/Standard Description

Solids by volume ISO 3233 98 ± 2 %

Gloss level (GU 60 °) ISO 2813 gloss (70-85)
Flash point ISO 3679 Method 1 100 °C
VOC-EU EU VOC Directive 2004/42/CE (theoretical) 22 g/l

The provided data is typical for factory produced products, subject to slight variation depending on colour.
All data is valid for mixed paint.
Gloss description: According to Jotun Performance Coatings' definition.

Film thickness per coat

Typical recommended specification range

Dry film thickness 50 - 200 μm

Wet film thickness 50 - 200 μm
Theoretical spreading rate 20 - 5 m²/l

Date of issue: 31 August 2018 Page: 1/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jotafloor Solvent Free Primer

Surface preparation
To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any
contamination.

Surface preparation summary table

Surface preparation

Substrate Minimum Recommended

Concrete and Coated Clean, dry and undamaged compatible Clean, dry and undamaged compatible
surfaces coating as per SSPC SP13/NACE NO 6 coating as per SSPC SP13/NACE NO 6
/ASTM D4258 -05 /ACI 503.6R- /ASTM D4258 -05 /ACI 503.6R-
97/SSPC-TR 5/ICRI TECHNICAL 97/SSPC-TR 5/ICRI TECHNICAL
GUIDELINE 03741/NACE02203 GUIDELINE 03741/NACE02203

Application
Application methods
The product can be applied by

Brush: Recommended.
Roller: Recommended.

Conditions during application :

The temperature of the substrate should be minimum 10 °C and at least 3 °C above the dew point of the air,
measured in the vicinity of the substrate. Good ventilation is usually required in confined areas to ensure proper
drying. The moisture content in the substrate should not exceed 4 % (by weight). The coating should not be
exposed to oil, chemicals or mechanical stress until fully cured.

Product mixing ratio (by volume)

Jotafloor Solvent Free Primer Comp A 2 part(s)

Jotafloor Solvent Free Primer Comp B (20) 1 part(s)

Jotafloor Solvent Free Primer Comp A 2 part(s)

Jotafloor Solvent Free Primer Comp B (40) 1 part(s)

Thinner/Cleaning solvent
Thinner: Jotun Thinner No. 17

Date of issue: 31 August 2018 Page: 2/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jotafloor Solvent Free Primer

Drying and Curing time

Substrate temperature 15 °C 23 °C 40 °C

Jotafloor Solvent Free Primer Comp B (20)

Surface (touch) dry 7h 5h 3h

Walk-on-dry 25 h 16 h 9h
Dry to over coat, minimum 24 h 15 h 6h
Dry to over coat, maximum, atmospheric 72 h 48 h 30 h
Dried/cured for service 10 d 7d 4d

Jotafloor Solvent Free Primer Comp B (40)

Surface (touch) dry 12 h 10 h 6h

Walk-on-dry 42 h 30 h 18 h
Dry to over coat, minimum 32 h 24 h 10 h
Dry to over coat, maximum, atmospheric 96 h 72 h 36 h
Dried/cured for service 12 d 9d 3d

Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness.

Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.

Dry to over coat, minimum: The recommended shortest time before the next coat can be applied.

Dry to over coat, maximum, atmospheric: The longest time allowed before the next coat can be applied.

Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended
environment/medium.

Induction time and Pot life

Paint temperature 23 °C

Jotafloor Solvent Free Primer Comp B (20)

Pot life 10 min

Jotafloor Solvent Free Primer Comp B (40)

Pot life 20 min

Jotafloor Solvent Free Primer Comp B (20) - 30 min. after poured on to the floor.
Jotafloor Solvent Free Primer Comp B (40) - 45 min. after poured on to the floor.

Date of issue: 31 August 2018 Page: 3/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jotafloor Solvent Free Primer

Product compatibility
Depending on the actual exposure of the coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.
Subsequent coat: epoxy, polyurethane

Packaging (typical)
Volume Size of containers
(litres) (litres)

Jotafloor Solvent Free Primer Comp A 3.33/13 5/20

Jotafloor Solvent Free Primer Comp B (20) 1.67/6.5 3/10
Jotafloor Solvent Free Primer Comp B (40) 1.67/6.5 3/10

The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary
due to local regulations.

Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.

Shelf life at 23 °C
Jotafloor Solvent Free Primer Comp A 24 month(s)
Jotafloor Solvent Free Primer Comp B (20) 24 month(s)
Jotafloor Solvent Free Primer Comp B (40) 24 month(s)

In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.

Green Building Standards

This product contributes to Green Building Standard credits by meeting the following specific requirements:

LEED®v4 (2013)
EQ credit: Low emitting materials
- VOC content for Floor coatings (100 g/l) (CARB(CSM)2007) and emission between 0.5 and 5.0 mg/m³ (CDPH
method 1.1).
MR credit: Building product disclosure and optimization
- Material Ingredients, Option 2: Material Ingredient Optimization, International Alternative Compliance Path -
REACH optimization: Fully inventoried chemical ingredients to 100 ppm and not containing substances on the
REACH Authorization list – Annex XIV, the Restriction list – Annex XVII and the SVHC candidate list.
- Environmental Product Declarations. Product-specific Type III EPD (ISO 14025;21930, EN 15804).

LEED® (2009) :
IEQ Credit 4.2: The VOC requirements of SCAQMD Rule 1113, 2004.

BREEAM® International (2016) Issue 2.0

Hea 02: Meets the VOC emission demands (ISO 16000-9/10 (2006) or CDPH method 1.1 (2010) and the VOC
content demands for Two-pack reactive performance coatings (80 g/l).
Mat 01: Product-specific Type III EPD (ISO 14025;21930, EN 15804).

Date of issue: 31 August 2018 Page: 4/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jotafloor Solvent Free Primer

BREEAM® International (2013)

Hea 02: VOC content for Two-pack performance coating WB (140 g/l) (EU Directive 2004/42/CE)

Additional certificates and approvals may be available on request.

Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.

Health and safety

Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.

Colour variation
When applicable, products primarily meant for use as primers or antifoulings may have slight colour variations
from batch to batch. Such products may fade and chalk when exposed to sunlight and weathering.

Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.

Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.

If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.

Date of issue: 31 August 2018 Page: 5/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com