Penguard Clear Sealer

Technical Data Sheet
612;4265 1 4265 epoxy ^(ValidationDate). 1
Penguard Clear Sealer
Product description
This is a two component transparent polyamide cured high molecular weight epoxy sealer coating. It has
excellent penetrating properties and is designed as a sealer coat for concrete surfaces. Can be used as primer or
finish coat in a complete system in atmospheric environments.
Typical use
Protective:
Suitable for concrete exposed to a wide range of environments.
Other
Colours
transparent
Product data
Property Test/Standard Description
Solids by volume ISO 3233 44 2 %
Gloss level (GU 60 ) ISO 2813 gloss (70-85)
Flash point ISO 3679 Method 1 25 C
VOC-EU IED (2010/75/EU) (calculated) 496 g/l
The provided data is typical for factory produced products, subject to slight variation depending on colour.
All data is valid for mixed paint.
Gloss description: According to Jotun Performance Coatings' definition.
Film thickness per coat

Typical recommended specification range
Dry film thickness 30 - 50 m

Wet film thickness 70 - 115 m
Theoretical spreading rate 14,7 - 8,8 m/l
Surface preparation
To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any
contamination.
Surface preparation summary table
Date of issue: 16 November 2015 Page: 1/4
This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Surface preparation
Substrate Minimum Recommended
Coated surfaces Clean, dry and undamaged compatible Clean, dry and undamaged compatible
coating (ISO 12944-5 6.1) coating (ISO 12944-5 6.1)
Concrete Low pressure water washing to a Minimum 4 weeks curing.Moisture
rough, clean, dry and laitance free content maximum 5 %.Low pressure
surface. water washing to a rough, clean, dry
and laitance free surface.
Application
Application methods
The product can be applied by
Spray: Use airless spray.

Brush: Recommended.
Roller: Recommended.
Product mixing ratio (by volume)
Penguard Clear Sealer Comp A 4 part(s)

Penguard Comp B 1 part(s)
Thinner/Cleaning solvent
Thinner: Jotun Thinner No. 17
Guiding data for airless spray

Nozzle tip (inch/1000): 15-23
Pressure at nozzle (minimum): 150 bar/2100 psi
Drying and Curing time

Substrate temperature 10 C 23 C 40 C
Surface (touch) dry 2h 1h 30 min

Walk-on-dry 14 h 6.5 h 4h
Dry to over coat, minimum 8h 4h 2h
Dried/cured for service 14 d 7d 3d
Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and
at average of the DFT range for the product.
Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness.

Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.
Dry to over coat, minimum: The shortest time allowed before the next coat can be applied.
Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended
environment/medium.
Induction time and Pot life

Paint temperature 23 C
Induction time 30 min

Pot life 8h
Heat resistance
Temperature
Continuous Peak
Dry, atmospheric 120 C 140 C
Peak temperature duration max. 1 hour.

The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these
temperatures.
Product compatibility
Depending on the actual exposure of the coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.
Subsequent coat: epoxy, polyurethane
Packaging (typical)
Volume Size of containers
(litres) (litres)
Penguard Clear Sealer Comp A 4/16 5/20

Penguard Comp B 1/4 1/5
The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary
due to local regulations.
Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.

Shelf life at 23 C
Penguard Clear Sealer Comp A 48 month(s)
Penguard Comp B 48 month(s)
In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.
Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.
Health and safety

Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.
Colour variation
When applicable, products primarily meant for use as primers or antifoulings may have slight colour variations
from batch to batch. Such products may fade and chalk when exposed to sunlight and weathering.
Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.
Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.
If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.


Penguard Clear Sealer

Uploaded by

Copyright:

Available Formats

Penguard Clear Sealer

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Penguard Clear Sealer

Uploaded by

Copyright:

Available Formats

Technical Data Sheet

612;4265 1 4265 epoxy ^(ValidationDate). 1

Penguard Clear Sealer

Film thickness per coat

Dry film thickness 30 - 50 m

Surface preparation summary table

Date of issue: 16 November 2015 Page: 1/4

This Technical Data Sheet supersedes those previously issued.

Substrate Minimum Recommended

Spray: Use airless spray.

Product mixing ratio (by volume)

Penguard Clear Sealer Comp A 4 part(s)

Guiding data for airless spray

Pressure at nozzle (minimum): 150 bar/2100 psi

Drying and Curing time

Surface (touch) dry 2h 1h 30 min

Date of issue: 16 November 2015 Page: 2/4

This Technical Data Sheet supersedes those previously issued.

Induction time and Pot life

Induction time 30 min

Dry, atmospheric 120 C 140 C

Peak temperature duration max. 1 hour.

Penguard Clear Sealer Comp A 4/16 5/20

Date of issue: 16 November 2015 Page: 3/4

This Technical Data Sheet supersedes those previously issued.

Health and safety

Date of issue: 16 November 2015 Page: 4/4

This Technical Data Sheet supersedes those previously issued.

You might also like