LM1458/LM1558 Dual Operational Amplifier

August 2000

LM1458/LM1558
Dual Operational Amplifier
General Description Features
The LM1458 and the LM1558 are general purpose dual op- n No frequency compensation required
erational amplifiers. The two amplifiers share a common bias n Short-circuit protection
network and power supply leads. Otherwise, their operation n Wide common-mode and differential voltage ranges
is completely independent. n Low-power consumption
The LM1458 is identical to the LM1558 except that the n 8-lead can and 8-lead mini DIP
LM1458 has its specifications guaranteed over the tempera- n No latch up when input common mode range is
ture range from 0˚C to +70˚C instead of −55˚C to +125˚C. exceeded

Connection Diagrams
Dual-In-Line Package
Metal Can Package

DS007886-2
DS007886-3

Top View Top View

Order Number LM1558H, Order Number LM1558J/883, LM1458M,
LM1558H/883 or LM1458H LM1458MX or LM1458N
See NS Package Number H08C See NS Package Number J08A, M08A or N08E

© 2000 National Semiconductor Corporation DS007886 www.national.com

LM1458/LM1558
Absolute Maximum Ratings (Note 1) Operating Temperature Range
LM1558 −55˚C to +125˚C
If Military/Aerospace specified devices are required, LM1458 0˚C to +70˚C
please contact the National Semiconductor Sales Office/
Storage Temperature Range −65˚C to +150˚C
Distributors for availability and specifications.
Lead Temperature (Soldering, 10 sec.) 260˚C
(Note 5)
Soldering Information
Supply Voltage Dual-In-Line Package
LM1558 ± 22V Soldering (10 seconds) 260˚C
LM1458 ± 18V Small Outline Package
Power Dissipation (Note 2) Vapor Phase (60 seconds) 215˚C
LM1558H/LM1458H 500 mW Infrared (15 seconds) 220˚C
LM1458N 400 mW See AN-450 “Surface Mounting Methods and Their Effect
Differential Input Voltage ± 30V on Product Reliability” for other methods of soldering
± 15V surface mount devices.
Input Voltage (Note 3)
ESD tolerance (Note 6) 300V
Output Short-Circuit Duration Continuous

Electrical Characteristics (Note 4)

Parameter Conditions LM1558 LM1458 Units
Min Typ Max Min Typ Max
Input Offset Voltage TA = 25˚C, RS ≤ 10 kΩ 1.0 5.0 1.0 6.0 mV
Input Offset Current TA = 25˚C 80 200 80 200 nA
Input Bias Current TA = 25˚C 200 500 200 500 nA
Input Resistance TA = 25˚C 0.3 1.0 0.3 1.0 MΩ
Supply Current Both TA = 25˚C, VS = ± 15V 3.0 5.0 3.0 5.6 mA
Amplifiers
Large Signal Voltage Gain TA = 25˚C, VS = ± 15V 50 160 20 160 V/mV
VOUT = ± 10V, RL ≥ 2 kΩ
Input Offset Voltage RS ≤ 10 kΩ 6.0 7.5 mV
Input Offset Current 500 300 nA
Input Bias Current 1.5 0.8 µA
Large Signal Voltage Gain VS = ± 15V, VOUT = ± 10V 25 15 V/mV
RL ≥ kΩ
Output Voltage Swing VS = ± 15V, RL = 10 kΩ ± 12 ± 14 ± 12 ± 14 V
RL = 2 kΩ ± 10 ± 13 ± 10 ± 13 V
Input Voltage Range VS = ± 15V ± 12 ± 12 V
Common Mode RS ≤ 10 kΩ 70 90 70 90 dB
Rejection Ratio
Supply Voltage RS ≤ 10 kΩ 77 96 77 96 dB
Rejection Ratio
Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits.
Note 2: The maximum junction temperature of the LM1558 is 150˚C, while that of the LM1458 is 100˚C. For operating at elevated temperatures, devices in the H08
package must be derated based on a thermal resistance of 150˚C/W, junction to ambient or 20˚C/W, junction to case. For the DIP the device must be derated based
on a thermal resistance of 187˚C/W, junction to ambient.
Note 3: For supply voltages less than ± 15V, the absolute maximum input voltage is equal to the supply voltage.
Note 4: These specifications apply for VS = ± 15V and −55˚C ≤ TA ≤ 125˚C, unless otherwise specified. With the LM1458, however, all specifications are limited to
0˚C ≤ TA ≤ 70˚C and VS = ± 15V.
Note 5: Refer to RETS 1558V for LM1558J and LM1558H military specifications.
Note 6: Human body model, 1.5 kΩ in series with 100 pF.

www.national.com 2
 LM1458/LM1558
Schematic Diagram

DS007886-1

Numbers in parentheses are pin numbers for amplifier B.

3 www.national.com
LM1458/LM1558
Physical Dimensions inches (millimeters) unless otherwise noted

Metal Can Package (H)

Order Number LM1558H, LM1558H/883 or LM1458H
NS Package Number H08C

Small Outline Package (M)

Order Number LM1458M or LM1458MX
NS Package Number M08A

www.national.com 4
 LM1458/LM1558
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)

Small Outline Package (M)

Order Number LM1458M or LM1458MX
NS Package Number M08A

Molded Dual-In-Line Package (N)

Order Number LM1458N
NS Package Number N08E

5 www.national.com
LM1458/LM1558 Dual Operational Amplifier
Notes

LIFE SUPPORT POLICY

NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or 2. A critical component is any component of a life
systems which, (a) are intended for surgical implant support device or system whose failure to perform
into the body, or (b) support or sustain life, and can be reasonably expected to cause the failure of
whose failure to perform when properly used in the life support device or system, or to affect its
accordance with instructions for use provided in the safety or effectiveness.
labeling, can be reasonably expected to result in a
significant injury to the user.
National Semiconductor National Semiconductor National Semiconductor National Semiconductor
Corporation Europe Asia Pacific Customer Japan Ltd.
Americas Fax: +49 (0) 180-530 85 86 Response Group Tel: 81-3-5639-7560
Tel: 1-800-272-9959 Email: europe.support@nsc.com Tel: 65-2544466 Fax: 81-3-5639-7507
Fax: 1-800-737-7018 Deutsch Tel: +49 (0) 69 9508 6208 Fax: 65-2504466
Email: support@nsc.com English Tel: +44 (0) 870 24 0 2171 Email: ap.support@nsc.com
www.national.com Français Tel: +33 (0) 1 41 91 8790

National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.