Sheet Name Description

SS Simply Supported 1 Simply Supported Dog legge

SSD Simply Supported Detailing and end on landing with beam
ESSC End Span With Floor Slab Continuous Small fixity, meaning their be
ES-WSCD End Span With Slab Continuous Detailing
ESELC End Span With Elevated Landing Continuous Not only the two cases, when
ESELC-D End Span With Elevated Landing Continuous Detailing supported slab. And the anal
IS Interior Span on the SS sheet,
ISD Interior Span Detailing
Simply supported Stairs enco
Developed by: Af( ephabey@gmail.com) only main rebar is provided a
amount of rebar could be pro

opening and closing joints sh

2 End span with slab continuou

fixity is available at the slab a
stair is supported on landing

In this case the stair become

3 End Span with Elevated Land

some other rigid mechanism
or any other mechanism that

4 Interior Span is developed wh

continuous with slab.
 Detail description
ply Supported Dog legged stairs are usually encountered when the stair starts from a slab on Ground
end on landing with beam supports.both Slab on Ground and landing supported on Beam has
all fixity, meaning their behaviour is better modeled with pin support.

only the two cases, whenever the designer deem necessary, the stair could be modeled as simply
ported slab. And the analysis procedure is based on simple statics, one could see the 'Analysis' Section
he SS sheet,

ply supported Stairs encounter only span moment and their detailing should follow the design, meaning
y main rebar is provided at the bottom and for consideration of the 'small fixity' at the end supports small
ount of rebar could be provided at the top of the stair.

ning and closing joints should be assessed carefully while performing detailing of any stairs.

d span with slab continuous is the case when the stair is continuous with floor slab. In such case considerable
y is available at the slab and one could consider that region to be fixed supported. And the other end of such
r is supported on landing beam or some other mechanism that doesn’t allow moment to be supported.

his case the stair becomes End Span and the continuous part is at Floor Level, Either bottom or Top Floor.

d Span with Elevated Landing continuous is the case when the landing is supported on Structural wall or
me other rigid mechanism that can support moment. And the floor level support may be slab on Ground
ny other mechanism that doesn't support moment.

rior Span is developed when the landing level is supported on Structural wall and the floor level support is
tinuous with slab.
 Stair Geometry
L1 0.500 m H’ 3.300 m d
a' 2.000 m T 0.280 m N
C 1.500 m R 0.150 m α
Material Data
C 20.000 Mpa γc 1.500 γc(Wt.)
S 500.000 Mpa γs 1.150 ν
Cover 30.000 mm Ø 14.000 mm E
αcc 0.850 fctm
Depth of Stair
d 235.294 Span Type Simple
D 272.294 mm k(Simple) 1.000 ρo 0.447
Take D 280.000 mm ρ 0.500 l/d[Adjusted] 17.000
User Preferred depth 200.000 mm
Dead Load
Waist Slab Section Material unit weight and thickness Landing Section
RCC Slab 5.672 KN/m γc(Wt.) 25.000 KN/m 3
RCC Slab
Steps 1.875 KN/m γm(mortar) 23.000 KN/m 3
Screed
Plastering 0.522 KN/m γff(marble) 27.000 KN/m 3
Floor Finish

Marble(riser) 0.289 KN/m t(plastering) 0.020 m Plastering

Screed(riser) 0.246 KN/m t(marble thread) 0.030 m Gk(landing)

Marble(thread) 0.810 KN/m t(marble riser) 0.020 m

Screed(thread) 0.460 KN/m t(screed) 0.020 m
Gk(Waist Slab) 9.875 KN/m
Live Load
Qk 3.000 KN/m 2

Design Load
Partial safety Factor
Gk 1.350 Pd(Waist Slab)
17.831 KN/m
Qk 1.500 Pd(Landing) 13.221 KN/m
Analysis
Dead Load Transfer Live Load Transfer
RX 15.481 KN RX 6.000 KN
RY 17.189 KN RY 6.000 KN
 Design Moment Calculation
RX 29.900 KN xmax 1.935 m
RY 32.205 KN Msd -32.818 KN-m
Reinforcement Design
Main Rebar
fcd 11.333 d 163.000 mm
fyd 434.783 Msd 32.818 KN-m
As 491.505 mm 2
Ø 14.000 mm
S 313.197 mm Smax 400.000 mm
Sprovided 310.000 mm
Main Rebar Provide φ 14 C/C 310
Secondary Rebar
Ø 10.000 mm
Smax 450.000 mm
Secondary Rebar Provide φ 10 C/C 450
Check depth from deflection control for the updated rebar percentage
 1.600 m
0.200 m
0.492 rad

25.000 KN/m3
0.200
30 Mpa
2.2 Mpa

k(End) 1.300
k(Interior) 1.500
k(Simple) 1.000
k(cantilever) 0.400

Landing Section
5.000 KN/m
0.460 KN/m
0.540 KN/m
0.460 KN/m
6.460 KN/m
 µsd 0.109
Kz 0.942

rcentage
 Stair Reinforcement Detailing

E(optional)
1.5 m 2m

D(optional)

Individual Bar Detail

1.35

0.35

2.2
0

Ø 14 C/C 310, L=4.4 m

0.49

1.63 0.13
 1.5
B 7

Ø 14 C/C 310, L=3.4 m

 Anchorage Length Lap Length
fctd 0.889 Mpa a 1
Ld 855.9 mm a1 2
As,cal 491.5 mm2 Lo,min 520 mm
As,prov. 496.6 mm 2 Lo 1700 mm
Lb,net 847.2 mm
0.5 m Lb,min t 260 mm
Lb,min c 510 mm
Lb,net t 850 mm
Lb,net c 850 mm

C(optional)

D(optional)

1.7
1.7
D E
1.2
3

0.4
7 Ø 14 C/C 310, L=3.4 m
0.485

Ø 14 C/C 310, L=2.2 m

0.7
C 7

0.47 0.485
 0.35

Ø 14 C/C 310, L=2.1 m

 1.7

310, L=3.4 m
 Stair Geometry
L1 0.600 m H’ 3.000 m d 1.500
a' 3.000 m T 0.280 m N 0.200
C 1.200 m R 0.150 m α 0.492
Material Data
C 20.000 Mpa γc 1.500 γc(Wt.) 25.000
S 400.000 Mpa γs 1.150 ν 0.200
Cover 25.000 mm Ø 12.000 mm E 30
αcc 0.850 fctm 2.2
Depth of Stair
d 173.756 Span Type End k(End)
D 204.756 mm k(Simple) 1.300 ρo 0.447 k(Interior)
Take D 210.000 mm ρ 0.500 l/d[Adjusted] 27.625 k(Simple)
User Preferred depth 190.000 mm k(cantilever)
Dead Load
Waist Slab Section Material unit weight and thickness Landing Section
RCC Slab 5.389 KN/m γc(Wt.) 25.000 KN/m 3
RCC Slab 4.750
Steps 1.875 KN/m γm(mortar) 23.000 KN/m 3
Screed 0.460
Plastering 0.522 KN/m γff(marble) 27.000 KN/m 3
Floor Finish 0.810
Marble(riser) 0.289 KN/m t(plastering) 0.020 m Plastering 0.460
Screed(riser) 0.246 KN/m t(marble thread) 0.030 m Gk(landing)
6.480
Marble(thread) 0.810 KN/m t(marble riser) 0.020 m
Screed(thread) 0.460 KN/m t(screed) 0.020 m
Gk(Waist Slab) 9.591 KN/m
Live Load
Qk 3.000 KN/m 2

Design Load
Partial safety Factor
Gk 1.350 Pd(Waist Slab)
17.448 KN/m
Qk 1.500 Pd(Landing) 13.248 KN/m
Analysis
Dead Load Transfer Live Load Transfer
a 2.700 m M(L End) 8.640
b 2.100 m Rx 5.400
Mab(landing) 18.662 KN-m Rx 14.209 KN Ry 9.000
Mab(flight) 7.383 KN-m Ry 26.228 KN
M(L End) 26.045 KN-m
 Design Moment
Mab(landing) 38.154 KN-m Rx 27.283 KN
Mab(flight) 9.967 KN-m Ry 48.908 KN
M(sd supp.) 48.121 KN-m xmax 2.947 m
M(sd Span) -26.915 KN-m
Reinforcement Design
Main Rebar Support
fcd 11.333 d 159.000 mm µsd
fyd 347.826 Msd 48.121 KN-m Kz
As 958.852 mm
2
Ø 12.000 mm
S 117.951 mm Smax 400.000 mm
Sprovided 110.000 mm
Main Rebar support Provide Ø 12 C/C 110
Main Rebar Span
fcd 11.333 d 159.000 mm µsd
fyd 347.826 Msd 26.915 KN-m Kz
As 511.966 mm
2
Ø 12.000 mm
S 220.908 mm Smax 400.000 mm
Sprovided 220.000 mm
Main Rebar span Provide Ø 12 C/C 220
Secondary Rebar
Ø 10.000 mm
Smax 450.000 mm
Secondary Rebar Provide Ø 10 C/C 450
Check depth from deflection control for the updated rebar percentage
 m
m
rad

KN/m3

Mpa
Mpa

1.300
1.500
1.000
0.400

ding Section
KN/m
KN/m
KN/m
KN/m
KN/m

Load Transfer
KN-m
KN-m
KN-m
0.168
0.907

0.094
0.951
 Stair Reinforcement Detailing

E(optional)
1.2 m 3m

F
B

Bar Spacing
A Provide Ø 12 C/C 220
B Provide Ø 12 C/C 220
C Provide Ø 12 C/C 110
D Provide Ø 12 C/C 110
E Provide Ø 12 C/C 220
F Provide Ø 10 C/C 450
 0.6 m

D
 Stair Geometry
L1 0.450 m H’ 2.850 m d 1.500
a' 3.000 m T 0.300 m N 0.300
C 1.350 m R 0.140 m α 0.437
Material Data
C(fck) 25.000 Mpa γc 1.500 γc(Wt.) 25.000
S 400.000 Mpa γs 1.150 ν 0.200
Cover 35.000 mm Ø 12.000 mm E 31
αcc 0.850 fctm 2.6
Depth of Stair
d 159.667 Span Type End k(End)
D 200.667 mm k(Simple) 1.300 ρo 0.500 k(Interior)
Take D 210.000 mm ρ 0.500 l/d[Adjusted] 30.063 k(Simple)
User Preferred depth 190.000 mm k(cantilever)
Dead Load
Waist Slab Section Material unit weight and thickness Landing Section
RCC Slab 5.242 KN/m γc(Wt.) 25.000 KN/m 3
RCC Slab 4.750
Steps 1.750 KN/m γm(mortar) 23.000 KN/m 3
Screed 0.460
Plastering 0.508 KN/m γff(marble) 27.000 KN/m 3
Floor Finish 0.810
Marble(riser) 0.252 KN/m t(plastering) 0.020 m Plastering 0.460
Screed(riser) 0.215 KN/m t(marble thread) 0.030 m Gk(landing)
6.480
Marble(thread) 0.810 KN/m t(marble riser) 0.020 m
Screed(thread) 0.460 KN/m t(screed) 0.020 m
Gk(Waist Slab) 9.236 KN/m
Live Load
Qk 3.000 KN/m 2

Design Load
Partial safety Factor
Gk 1.350 Pd(Waist Slab)
16.969 KN/m
Qk 1.500 Pd(Landing) 13.248 KN/m
Analysis
Dead Load Transfer Live Load Transfer
a 2.850 m M(R End) 8.640
b 1.950 m RX 9.000
Mab(landing) 18.662 KN-m RX 24.037 KN RY 5.400
Mab(flight) 5.944 KN-m RY 15.335 KN
M(REnd) 24.606 KN-m
 Design Moment
Mab(landing) 38.154 KN-m RX 45.950 KN
Mab(flight) 8.024 KN-m RY 28.802 KN
M(sd supp.) 46.178 KN-m xmax 1.796 m
M(sd Span) -26.992 KN-m
Reinforcement Design
Main Rebar Support
fcd 14.167 d 149.000 mm µsd
fyd 347.826 Msd 46.178 KN-m Kz
As 968.270 mm
2
Ø 12.000 mm
S 116.804 mm Smax 400.000 mm
Sprovided 110.000 mm
Main Rebar support Provide φ 12 C/C 110
Main Rebar Span
fcd 14.167 d 149.000 mm µsd
fyd 347.826 Msd 26.992 KN-m Kz
As 545.316 mm
2
Ø 12.000 mm
S 207.398 mm Smax 400.000 mm
Sprovided 200.000 mm
Main Rebar Span Provide φ 12 C/C 200
Secondary Rebar
Ø 10.000 mm
Smax 450.000 mm
Secondary Rebar Provide φ 10 C/C 450
Check depth from deflection control for the updated rebar percentage
 m
m
rad

KN/m3

Mpa
Mpa

1.300
1.500
1.000
0.400

ding Section
KN/m
KN/m
KN/m
KN/m
KN/m

oad Transfer
KN-m
KN-m
KN-m
0.147
0.920

0.086
0.955
 Stair Reinforcement Detailing

E
1.35 m 3m

F
B

Bar Spacing
A Provide φ 12 C/C 200
B Provide φ 12 C/C 200
C Provide φ 12 C/C 200
D Provide φ 12 C/C 200
E Provide φ 12 C/C 110
F Provide φ 10 C/C 450
 0.45 m

D
 Stair Geometry
L1 0.700 m H’ 3.500 m d 1.500
a' 3.000 m T 0.300 m N 0.900
C 1.500 m R 0.150 m α 0.464
Material Data
C 25.000 Mpa γc 1.500 γc(Wt.) 25.000
S 400.000 Mpa γs 1.150 ν 0.200
Cover 25.000 mm Ø 12.000 mm E 31
αcc 0.850 fctm 2.6
Depth of Stair
d 149.910 Span Type Interior k(End)
D 180.910 mm k(Interior) 1.500 ρo 0.500 k(Interior)
Take D 190.000 mm ρ 0.500 l/d[Adjusted] 34.688 k(Simple)
User Preferred depth 170.000 mm k(cantilever)
Dead Load
Waist Slab Section Material unit weight and thickness Landing Section
RCC Slab 4.752 KN/m γc(Wt.) 25.000 KN/m 3
RCC Slab 4.250
Steps 1.875 KN/m γm(mortar) 23.000 KN/m 3
Screed 0.460
Plastering 0.514 KN/m γff(marble) 27.000 KN/m 3
Floor Finish 0.810
Marble(riser) 0.270 KN/m t(plastering) 0.020 m Plastering 0.460
Screed(riser) 0.230 KN/m t(marble thread) 0.030 m Gk(landing)
5.980
Marble(thread) 0.810 KN/m t(marble riser) 0.020 m
Screed(thread) 0.460 KN/m t(screed) 0.020 m
Gk(Waist Slab) 8.911 KN/m
3.000
Qk 3.000 KN/m 2

Design Load
Partial safety Factor
Gk 1.350 Pd(Waist Slab)
16.530 KN/m
Qk 1.500 Pd(Landing) 12.573 KN/m
Analysis
Dead Load Transfer Live Load Transfer
a 3.000 m M(R End) 10.140
b 2.200 m RX 7.800
Mab(landing) 13.475 KN-m RX 19.050 KN RY 7.800
Mab(flight) 4.380 KN-m RY 20.838 KN
Mba(flight) 5.512 Left=a
M(REnd) 18.987 KN-m Right=b
M(LEnd) 17.855 KN-m
 Design Moment
Mab(landing) 28.331 KN-m RX 37.418 KN
Mab(flight) 5.913 KN-m RY 39.832 KN
Mba(flight) 7.441 KN-m xmax 2.577 m
M(lsd supp.) 34.244 KN-m
M(rsd supp.) 35.772 KN-m
M(sd Span) -18.156 KN-m
Reinforcement Design
Main Rebar Support
fcd 14.167 d 139.000 mm µsd
fyd 347.826 Msd 35.772 KN-m Kz
As 795.825 mm
2
Ø 12.000 mm
S 142.113 mm Smax 400.000 mm
Sprovided 140.000 mm
Main Rebar support Provide Ø 12 C/C 140
Main Rebar Span
fcd 14.167 d 139.000 mm µsd
fyd 347.826 Msd 18.156 KN-m Kz
As 388.892 mm
2
Ø 12.000 mm
S 290.819 mm Smax 400.000 mm
Sprovided 290.000 mm
Main Rebar span Provide Ø 12 C/C 290
Secondary Rebar
Ø 8.000 mm
Smax 450.000 mm
Secondary Rebar Provide Ø 8 C/C 450
Check depth from deflection control for the updated rebar percentage
k(Interior) 1.500 ρo 0.500 %
 m
m
rad

KN/m3

Mpa
Mpa

1.300
1.500
1.000
0.400

ding Section
KN/m
KN/m
KN/m
KN/m
KN/m

Load Transfer
KN-m
KN-m
KN-m
0.131
0.930

0.066
0.966
 Stair Reinforcement Detailing

E
1.5 m 3m

F
B

A Provide Ø 12 C/C 290

B Provide Ø 12 C/C 290
C Provide Ø 12 C/C 140
D Provide Ø 12 C/C 140
E Provide Ø 12 C/C 140
F Provide Ø 8 C/C 450
 0.7 m