RG10 - RG10Y SUPER FAST RECTIFIER DIODES

PRV : 70 - 600 Volts D2

Io : 1.0 - 1.5 Amperes
FEATURES :
1.00 (25.4)
* High current capability 0.161 (4.1) MIN.
* High surge current capability 0.154 (3.9)
* High reliability
* Low reverse current 0.284 (7.2)
* Low forward voltage drop 0.268 (6.8)
* Super fast recovery time
1.00 (25.4)
MECHANICAL DATA : 0.034 (0.86) MIN.
* Case : D2 Molded plastic 0.028 (0.71)
* Epoxy : UL94V-O rate flame retardant
* Lead : Axial lead solderable per MIL-STD-202,
Method 208 guaranteed
Dimensions in inches and ( millimeters )
* Polarity : Color band denotes cathode end
* Mounting position : Any
* Weight : 0.465 gram

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Rating at 25 ° C ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%.

RATING SYMBOL RG10Y RG10 RG10A UNITS

Maximum Recurrent Peak Reverse Voltage VRRM 70 400 600 Volts
Maximum RMS Voltage VRMS 49 280 420 Volts
Maximum Reverse Voltage VDC 70 400 600 Volts
Maximum Average Forward Current
0.375"(9.5mm) Lead Length Ta = 55 °C IF(AV) 1.5 1.2 1.0 Amp.
Peak Forward Surge Current,
8.3ms Single half sine wave Superimposed
on rated load (JEDEC Method) IFSM 50 Amps.
Maximum Peak Forward Voltage at IF = 1.0 A. VF 1.1 1.8 2.0 Volts
Maximum DC Reverse Current Ta = 25 °C IR 5 µA
at Rated DC Blocking Voltage Ta = 100 °C IR(H) 50 µA
Maximum Reverse Recovery Time ( Note 1 ) Trr 35 ns
Typical Junction Capacitance ( Note 2 ) CJ 50 pf
Junction Temperature Range TJ - 65 to + 150 °C
Storage Temperature Range TSTG - 65 to + 150 °C

Notes :
( 1 ) Reverse Recovery Test Conditions : IF = 0.5 A, IR = 1.0 A, Irr = 0.25 A.
( 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 VDC UPDATE : APRIL 23, 1998
 RATING AND CHARACTERISTIC CURVES ( RG10 - RG10Y )

FIG.1 - REVERSE RECOVERY TIM E CHARACTERISTIC AND TEST CIRCUIT DIAGRAM

50 Ω 10 Ω Trr

+ 0.5 A

D.U.T. 0
+ PULSE
- 0.25
50 Vdc GENERATOR
(approx) ( NOTE 2 )

1Ω OSCILLOSCOPE - 1.0 A
( NOTE 1 )
SET TIME BASE FOR 15 ns/cm
NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF. 1 cm
2. Rise time = 10 ns max., Source Impedance = 50 ohms.
3. All Resistors = Non-inductive Types.

FIG.2 - DERATING CURVE FOR OUTPUT FIG.3 - MAXIMUM NON-REPETITIVE PEAK

RECTIFIED CURRENT FORWARD SURGE CURRENT
PERCENTAGE AGAINST RATED

100 50
8.3 ms SINGLE HALF SINE WAVE
PEAK FORWARD SURGE

Ta = 50 °C
CURRENT, AMPERES
CURRENT Io (%)

80 40

60 30

40 20

20 10

60Hz RESISTIVE OR INDUCTIVE LOAD

0 0
0 25 50 75 100 125 150 175 1 2 4 6 10 20 40 60 100

AMBIENT TEMPERATURE, ( ° C) NUMBER OF CYCLES AT 60Hz

FIG.4 - TYPICAL FORWARD CHARACTERISTICS FIG.5 - TYPICAL REVERSE CHARACTERISTICS

REVERSE CURRENT, MICROAMPERES

100 10

TJ = 100 °C
FORWARD CURRENT, AMPERES

10 1.0

RG10Y RG10

1.0 0.1
RG10A
TJ = 25 °C

0.1 0.01
Pulse Width = 300 µs 0 20 40 60 80 100 120 140
2% Duty Cycle
PERCENT OF RATED REVERSE
TJ = 25 °C
VOLTAGE, (%)
0.01
0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4

FORWARD VOLTAGE, VOLTS

This datasheet has been download from:

www.datasheetcatalog.com

Datasheets for electronics components.