TH97/2478 TH09/2479 IATF 0113686

SGS TH07/1033
www.eicsemi.com

FR201 - FR207-STR FAST RECOVERY

RECTIFIER DIODES
PRV : 50 - 1000 Volts D2
Io : 2.0 Amperes
FEATURES :
1.00 (25.4)
* High current capability 0.161 (4.1) MIN.
* High surge current capability 0.154 (3.9)

* High reliability
* Low reverse current 0.284 (7.2)
* Low forward voltage drop 0.268 (6.8)
* Fast switching for high efficiency
* Pb / RoHS Free
1.00 (25.4)
MECHANICAL DATA : 0.034 (0.86) MIN.
0.028 (0.71)
* Case : D2 Molded plastic
* Epoxy : UL94V-O rate flame retardant
* Lead : Axial lead solderable per MIL-STD-202,
Method 208 guaranteed Dimensions in inches and ( millimeters )
* Polarity : Color band denotes cathode end
* Mounting position : Any
* Weight : 0.465 gram

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Rating at 25 °C ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%.

FR207
RATING SYMBOL FR201 FR202 FR203 FR204 FR205 FR206 FR207 UNIT
-STR
Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 400 600 800 1000 1000 V
Maximum RMS Voltage VRMS 35 70 140 280 420 560 700 700 V
Maximum DC Blocking Voltage VDC 50 100 200 400 600 800 1000 1000 V
Maximum Average Forward Current
IF(AV) 2.0 A
0.375"(9.5mm) Lead Length Ta = 55 °C
Peak Forward Surge Current,
8.3ms Single half sine wave Superimposed IFSM 75 A
on rated load (JEDEC Method)
Maximum Peak Forward Voltage at IF = 2.0 Amps. VF 1.3 V
Maximum DC Reverse Current Ta = 25 °C IR 10 µA
at Rated DC Blocking Voltage Ta = 100 °C IR(H) 500 µA
Maximum Reverse Recovery Time ( Note 1 ) Trr 150 250 500 250 ns
Typical Junction Capacitance ( Note 2 ) CJ 15 pf
Junction Temperature Range TJ - 65 to + 150 °C
Storage Temperature Range TSTG - 65 to + 150 °C

Notes :
( 1 ) Reverse Recovery Test Conditions : IF = 0.5 A, IR = 1.0 A, Irr = 0.25 A.
( 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 VDC
Page 1 of 2 Rev. 02 : March 24, 2005
 TH97/2478 TH09/2479 IATF 0113686
www.eicsemi.com SGS TH07/1033

RATING AND CHARACTERISTIC CURVES ( FR201 - FR207-STR )

FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM

Trr
50 Ω 10 Ω

+ 0.5 A

D.U.T. 0
+ PULSE
- 0.25 A
50 Vdc GENERATOR
(approx) ( NOTE 2 )

1Ω OSCILLOSCOPE - 1.0 A
( NOTE 1 )
SET TIME BASE FOR 50-100 ns/cm
NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF. 1 cm
2. Rise time = 10 ns max., Source Impedance = 50 ohms.
3. All Resistors = Non-inductive Types.

FIG.2 - DERATING CURVE FOR OUTPUT FIG.3 - MAXIMUM NON-REPETITIVE PEAK

RECTIFIED CURRENT FORWARD SURGE CURRENT
2.0 75
AVERAGE FORWARD OUTPUT

8.3 ms SINGLE HALF SINE WAVE

PEAK FORWARD SURGE
CURRENT, AMPERES
CURRENT, AMPERES

1.6 60

Ta = 55 °C
1.2 45

0.8 30

0.4 15

60Hz RESISTIVE OR INDUCTIVE LOAD

0 0
0 25 50 75 100 125 150 175 1 2 4 6 10 20 40 60 100

AMBIENT TEMPERATURE, ( °C) NUMBER OF CYCLES AT 60Hz

FIG.4 - TYPICAL FORWARD CHARACTERISTICS FIG.5 - TYPICAL REVERSE CHARACTERISTICS

100 10

Pulse Width = 300 µs TJ = 100 °C

REVERSE CURRENT,
FORWARD CURRENT, AMPERES

2% Duty Cycle
MICROAMPERES

TJ = 25 °C
10 1.0

1.0 0.1
TJ = 25 °C

0.1 0.01
0 20 40 60 80 100 120 140

PERCENT OF RATED REVERSE

VOLTAGE, (%)
0.01
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0

FORWARD VOLTAGE, VOLTS

Page 2 of 2 Rev. 02 : March 24, 2005