Compressed air management systems

Control systems Made in

for compressors and compressed air stations Germany

Efficient and reliable!

RENNERtronic RENNERtronic Plus RENNERcontrol Touch RENNERconnect

RENNER compressor control systems
Compressed air supply must work reliably and economically. RENNER intelligent control systems ensure that for both single and multiple
compressor stations.

RENNERlogic – RENNER‘s standard control system

RENNERlogic – a controller that is both functional and simple with many benefits!

Features:
• the start button starts up the compressor, the stop button makes the compressor go into shut off delay
• emergency stop: the compressor switches off immediately in emergency situations
• LED display: the compressor status is displayed by various flashing patterns.
• remote-indicating thermostat monitoring the temperature of the system
• hour meter to easily monitor operating hours
• pressure gauge and switch to check and control pressure
• DIP switch to easily set the shut off delay and start up period
• Modbus RTU, for example, to connect to a higher level control system

Advantages:
• standard: terminals in the switching cabinet to connect an external on/off switch
• standardised: potential free signals, fault and stand by messages
• simplified: automatic restart after power failure by connecting an additonal board (90 seconds time delay)
• option: the compressor can be turned off via an external signal

Standard equipment
• RENNER screw compressors from 2.2 – 55.0 kW

2
RENNERtronic RENNERtronic Plus
The user-friendly basic control The compressor control with additional functions

Performance features Performance features

Pressure control within two adjustable pressure bands: The RENNERtronic Plus has all the functions of the standard
Customers can determine two pressure bands within limits set by the RENNERtronic. And it can do even more!
factory. Based on these pressure bands the compressor is controlled.
Real-time clock: All functions can be called up on the large display
Capture of operating and load hours: To identify uneconomi- with real-time clock. The internal software has a timer with 7 channels.
cal operation where load hours are highly variable.
Base load change over function: This software comes with a base
Monitoring of adjustable maintenance intervals: For ­different load change over function which will be connected via RS485 inter-
compressor components, such as air or oil filters, maintenance inter- face (modbus) to a maximum of 4 additional compressors.
vals can be programmed. A message appears when maintenance is due.
Hardware: The hardware also has additional features: RENNER-
Fault memory: The last ten messages stating the current operating tronic Plus has 11 digital inputs (the RENNERtronic has 5), 8 digital
hours are displayed on the control for diagnostic purposes. outputs (instead of 6), 1 analog input for a temperature sensor and
3 for pressure transducers and current transformers. Both analog
Different code levels: The menu system is protected from unau- outputs can be used without an additional module. Easier operation
thorised changes by various code numbers (e.g. factory code, service due to a larger display.
code, customer code).
Monitoring of system pressure: System pressure is monitored
Base load change over function: The control has a base load via a pressure transducer connected to the air end. The compressor
change over function that can be activated via the menu (additional only starts up after full discharge; shut off delay time can be control­
module required). led by system pressure. In addition, the controller checks whether the
mains pressure is building up, for example to identify a belt break.
Control of frequency converters: A PI control is integrated for
controlling compressors with variable speed control. This control de-
termines the rotating speed setpoint depending on the set pressure
limit and transmits this to the converter as an analog signal (addi-
tional module).

Modbus RTU: serves, for instance, for the connection to a higher­level

control system or a building control system (Industry 4.0 Ready).

Advantages Options
• saves energy • profibus connection
• safe operation of the compressor
• controls and monitors the system Standard equipment
• easy to use • SLM-S 7.5 – 30.0
• greater reliability of operation • water injected compressors (RSW)
• can be exhanced according to specific customer requirements
• optional compressor monitoring ndustry 4.0 Optionally available for: Part no.
• starting with RS 75 in different versions 05591
Standard equipment
• for all compressors with frequency converters
• Starting with RS 75 in different versions • RS-PRO 2-30.0 – 55.0 D
• For all compressors with variable speed control • Booster (RSM)
• RS-PRO 2-30.0 – 55.0 D
• Booster (RSM) • RENNER screw compressors from 2.2 – 55.0 kW 00829
• SL-S 1.5 – 5.5
Optionally available for: Part no.
• RENNER screw compressors from 2.2 – 55.0 kW 10869
• SL-S / SL-I 1.5 – 7.5

3
Base load change over (BLCO)

Advantages of BLCO
• even workload for all compressors in terms of operating hours K2 K2
K1 K2 K3
• maintenance work can be done during operation

• all compressors are activated with

the same switch on / off pressure Master Slave 1 Slave 2
1 2 3
• high potential for energy savings
3 1 2
• high efficiency for fluctuating air demand 2 3 1

• user-friendly configuration Master compressor: is always the same compressor; Master con­
trols, which and how many compressors are activated.
• compressors from other manufacturers Base Load compressor: is the compressor that is activated first (K1)
can be connected and activated Switching interval: the base load compressor alternates after a
defined number of load hours. The switching interval can be adjusted.

BLCO installed in compressor

1. Using RENNERtronic control: The master compressor must Other features: The base load compressor can be activated by a
be equipped with RENNERtronic. All other compressors (up to 4) are timer. The base load compressor can be one particular compressor
controlled by the MK200 module. and all other compressors take turns.

2. Using RENNERtronic Plus: Up to 4 other compressors (slaves) Application examples: A new energy efficient compressor runs
can be connected. The compressors are connected via an RS485- permanently and covers all demand for air. A second, old compres-
interface. Compressors from other manufacturers are connected via sor will be activated once a week for 2 hours to prevent standstill
a slave module. damage.

A high-performance compressor with variable speed control has pri-

ority during day time. At night priority is given to a RS-B which is
sufficient for the lower air demand that time.
BLCO Master
(RENNERtronic Plus) The base load compressor can be determined, all other peak load
K1 compressors alternate.

Connecting cable BLCO installed in compressor

RS485, part no. 20451 or
RENNERsimply-connect Option Part no.

BLCO Master (RENNERtronic) for up to 4 Slaves 10680

BLCO Master (RENNERtronic Plus) for up to 4 Slaves incl.
BLCO Slave (RENNERtronic, RENNERlogic and SCROLL)
K2 K2 to connect to a superordinate control system via digital 05581
K2 K3 K5 inputs and outputs
BLCO Slave (RENNERtronic / RENNERlogic) via RS485 incl.
BLCO Slave BLCO Slave BLCO Slave Compressor of other Adjustment of circuit diagram for compressors of other
(RENNERtronic) (RENNERlogic) (RENNERtronic) manufacturers
manufacturers for BLCO (circuit diagram must be provided 03155
No additional No additional No additional Connecting
by client)
equipment required equipment required equipment required module
BLCO Slave Sensor cable 2 x 0.5 mm² shielded cable
00979
Part no. 17485 (BLCO with RENNERtronic Plus)
Connecting cable 10 x 0.75 mm² (BLCO with RENNERtronic) 15475
up to 5 compressors (4 Slaves)
4
RENNERsimply-connect
The easy solution to connect compressors.

RENNERsimply-connect is a system providing an easy and quick way to connect RENNER compressors via RS485 bus. RENNERsimply-connect is
universally applicable, whether you would like to implement an integrated base load change over or connect to a superordinate control system.
Prefabricated connecting cables and terminals eliminate the need for complicated wiring. Simply guide the connecting cable into the switch
cabinet, plug it in, and the RS485 connection will be established. The system works with BLCO with the RENNERtronic Plus, RENNERcontrol and
RENNERconnect. RENNERsimply-connect can be pre-assembled in your compressor or is available as a retrofit kit.

Controller (back)
RENNERsimply-connect

BLCO Master Slave 1 Slave 2

Model Description Part no.

RENNERsimply-connect Connecting system mounted in compressor to simply and quickly connect compressors. RENNERsimply- 07975
connect consists of two RJ45-sockets, which are mounted ex factory in the switch cabinet of the
compressor. It works for BLCO with RENNERtronic, RENNERtronic Plus and RENNERlogic.
RENNERsimply-connect Logic Retrofit kit for compressors with RENNERlogic, RENNERtronic und RENNERtronic Plus control systems. 07985
Connecting system to simply and quickly connect compressors. RENNERsimply-connect-logic / -tronic /
RENNERsimply-connect Tronic -tronic Plus consists of two RJ45-sockets, which are mounted in the switch cabinet of the compressor. 08469
They are plugged into the RENNERtronic by means of a built-in connecting cable including connector
RENNERsimply-connect Tronic Plus (RENNERlogic model without connector). Two cable glands for retrofitting are also included. 08416

RENNERsimply-connect RSC 5 m Connecting cable suitable for RENNERsimply-connect system, completely pre-assembled connectors 08239
RENNERsimply-connect RSC 10 m Connecting cable suitable for RENNERsimply-connect system, completely pre-assembled connectors 07990
RENNERsimply-connect RSC 15 m Connecting cable suitable for RENNERsimply-connect system, completely pre-assembled connectors 08738
RENNERsimply-connect RSC 20 m Connecting cable suitable for RENNERsimply-connect system, completely pre-assembled connectors 07921
RENNERsimply-connect RSC 30 m Connecting cable suitable for RENNERsimply-connect system, completely pre-assembled connectors 20199

5
BLCO in wall mounting box (RENNERcontrol Touch)
RENNERcontrol Touch is a base load change over in a wall mounting box with web visualization and touchscreen.
It is available in different versions.

E-mail dispatch
Part no. 21537
Signal pillar Pressure sensor Flow sensor Dew point sensor
Part no. 21471 Part no. 01378 Part no. 04804 Part no. 04807
RENNERcontrol Touch
Part no. 17483
17484
VPN

Connecting cable RS485

Part no. 20451
or RENNERsimply-connect

K2 K2
K1 K2 K3 K4
RENNERtronic RENNERlogic RENNERtronic Plus Compressor of other manufacturers Connection for
No additional equipment required No additional equipment required No additional equipment required Connecting module digital messages via
BLCO Slave additional module
Part no. 17485 Part no. 17485

RENNERcontrol Touch
Webserver with base load change over and 7“ touchscreen. Visuali- Advantages of RENNERcontrol Touch
zation and monitoring of compressors via network and at site; BLCO
for up to 4 compressors. • easy to retrofit

• visualization of compressors
RENNERcontrol Touch without web visualisation
Like RENNERcontrol Touch, but without webserver • enhanced fault and maintenance management

The compressors are connected via RS485 interface of the RENNER • analysis of 3 additional analog sensors
control systems RENNERlogic, RENNERtronic und RENNERtronic Plus.
Compressors of other manufacturers and other digital signals can be • E-mail reports maintenance and malfunction
connected via an additional connection module.
• digital inputs / outputs can be expanded via additional module

Base load change over + webserver in wall mounting box

Model Part no.

RENNERcontrol Touch 17483

RENNERcontrol Touch without webser visualization 17484

6
The basic view shows the current network pressure, the current If a compressor is selected, the current state will be explained in
state of the compressors as well as date and time. Detailed informa- more detail. From this screen other details like oil temperature pro-
tion can be retrieved by directly selecting the respective data. file, fault message memory, and maintenance data can be retrieved.

Not Aus

Fault indication of the selected compressor Display of maintenance schedule and the operating hours of
the selected compressor

Temperature profile
bar

Visualisation of the pressure profile of selected compressors Display of the temperature profile of compressor and room

7
 RENNERconnect with 7“ touchscreen
Does your compressed air station work economically? RENNERconnect is a higher level, intelligent control system for optimal management
and monitoring of your compressed air station. RENNERconnect contributes to efficiency and is highly reliable. Intelligent, air-demand based
connection of the compressors provides not only a high energy savings potential, but also ensures increased operational reliability of your
compressors. The control can be operated intuitively and safely via the integrated touchscreen.

Connectivity:
RENNERconnect
Part no. 14873
17489
14874

Server
VPN

Connecting cable
RS485
Part no. 20451
or
RENNERsimply-connect

up to 3 additional components
(analog inputs)

analog or digital inputs and outputs

K4
FU

K2
K4 K6
Compressor of other Compressor of other Connecting
K2 manufacturers
Connecting module
manufacturers
Connecting module
module
­RENNERconnect
K1 K2 K3 K5 RENNERconnect
Part no. 10546
RENNERconnect
Part no. 10546
Part no. 10546

RENNERtronic RENNERlogic RENNERtronic Plus RENNERtronic

No additional No additional No additional No additional
equipment required equipment required equipment required equipment required

up to 16 compressors up to 8 connecting modules

8
Features of the RENNERconnect:

1) Regardless of the compressor type, up to 16 compressors can 3) All compressors are connected via RS485-bus-system.
be controlled:
• RENNER compressors 4) RENNERconnect can connect to various additonal components in
• compressors of other manufacturers your compressor room and monitor them (e.g. dryer, drain, dew point
• standard compressors with load and no-load control sensor, flow sensor, additional pressure sensors).

2) All compressors operate in a common, narrow pressure band, 5) DIN ISO 50001: The control system can be used as energy manage­
which means: ment tool according to DIN ISO 50001 (section 4.6.1. monitoring,
• all compressors are activated at the same switch on/off pressure measurement, analysis). Contact us, we gladly ­provide you with
• pressure band can be reduced to a minimum information!
• high potential for energy savings, as pressure can be reduced
maximally
• older compressor stations can be operated more economically

• extremely low switching frequency (extends the service life of all mechanical components of the compressors)

• particularly low energy cost due to constant calculation of air consumption which ensures an efficient use of compressor capacity

Advantages of RENNERconnect

• Compressors with RENNERtronic, RENNERtronic Plus or RENNERlogic can be directly connected to RENNERconnect.

• Compressors of other manufacturers can be connected by simply applying a compact connecting module.

• Maximum energy savings (up to 40%) by avoiding expensive idle time and load / unload switching cycles, pressure optimization by
4 adjustable pressure bands and by reduction of maximum pressure.

• Extends the service life of suction controls, air ends, contactors and motors! The service cost corresponds to the actual load times.

• RENNERconnect matches the use of the compressors automatically with the demand for compressed air in order to generate just the
right amount needed for production.

ndustry 4.0
Connect your central control system via modbus with RENNER com- Intelligent interconnectedness of the components enables communi-
pressors and benefit from extensive possibilities of network data ex- cation between compressed air production, air treatment as well as
change in real time. Whether you want to focus on status monitoring, their optimal adjustment to achieve maximum efficiency.
look at fault reports, or retrieve service messages, all information is
available and ready to be gathered. Communication interfaces of the
control systems are used between the individual RENNER compres-
sors and secure full access as well as full control of the compressed
air station.

9
Webserver for the RENNERconnect control system
In control of your compressed air station – always and everywhere
• webserver is part of every RENNERconnect control system
• all current measurements are displayed on webserver
• up to date online analysis of the operation of the compressors and other equipment
• statistical analysis of all parameters in daily, weekly, or monthly reports
• compressors and equipment can be set and parameterized via webserver
• optionally: automatic forwarding of daily reports
• calculation of service dates in accordance with operating hours of compressor
• remote control of pressure profiles, sequences and timer via webserver

Energy balance and cost calculation:

The energy and cost calculation is available for each completed day. Several days up to a full month can be merged. The table can be exported in
Excel or Word format for further use.

Maintenance summary

10
Main View Dew-Point-Diagram

View of all connected compressors and sensors All connected sensors can be displayed graphically. Exceeding or under­
shooting alarm thresholds triggers selectable alarm responses.

Panel-Designer Total diagram

m3/min

bar

With the integrated panel designer, you can create a professional A clear overall diagram shows at a glance the pressure profile, flow rate
image of your station. as well as the operating times of the compressor.

Webserver Plus
An integrated service and alarm management will be provided by the option „Webserver Plus“:
• sending eMails in case of faults, warnings, and maintenance
• message, if limit values of pressure, dew point, and temperature are exceeded fall below minimum

RENNERconnect-Control System
Model Description Part no.

RENNERconnect in plastic housing – superordinated control for up to 16 compressors, two of which (optionally 4 / 6 / 8)
space for max. 1 connecting module for additional signals can be compressors with variable speed control (inverter) 14873
(dimensions: 490 x 390 x 130 mm) – option to connect 8 additonal modules with digital and analog input and output
RENNERconnect in plastic housing for a total of 16 analog sensors with 4-20 mA and 24 digital inputs for monitoring
space for max. 4 connecting modules for additonal signals (fault messages of dryers, drains, filters, operating reports …) 17489
(dimensions: 500 x 500 x 200 mm) – incl. pressure sensor
– includes compressed air visualisation (web server)
RENNERconnect without housing – remote programming and configuring of control system 14874
to be mounted into existing switch cabinet – 7“ touchscreen

11
COMPRESSED AIR FOR ALL APPLICATIONS

RENNER GmbH Kompressoren, a family run business established in 1994, develops and assembles economical and energy-efficient compressors.
A broad range of compressed air accessories are also part of the product portfolio. The structure and size of the company ensure flexible
decisions and short lead times, thus providing optimal focus on the requirements of the customers.

THE RENNER MANUFACTURING AND SUPPLY PROGRAMME:

We can supply you with the right compressor for any application – guaranteed.

SCREW COMPRESSORS: PISTON COMPRESSORS:

• from 2.2 to 355 kW • from 1.5 to 11.0 kW
• up to 40 bar, e.g. for manufacture of PET bottles • stationary or mobile, with or without sound insulation
• compact systems with air receiver, refrigeration dryer,
and ­variable speed control CONTROL SYSTEMS:
• heat exchanger integrated or as an external box • compressor control systems
• special applications: gas compression, operation of • superordinate control systems
drilling devices, rail, and special-purpose vehicles • state-of-the-art web server monitoring ndustry 4.0
• customized models designed to customer specifications
COMPRESSED AIR ACCESSORIES:
OIL-FREE COMPRESSORS: • air filters, air receivers, refrigeration dryers, adsorption dryers,
• SCROLL compressors for oil-free compressed air from 1.5 to 30.0 kW condensate drains, and oil-water-separators
• water-injected screw compressors for oil-free compressed air
in breathing air quality from 18.5 to 120 kW

RENNER GmbH ∙ Kompressoren

Your RENNER distributor:
Emil-Weber-Strasse 32
D-74363 Gueglingen
Steuerungen - EN - 03/2019 - PDF

Phone +49 (0) 7135 93193-0

Fax +49 (0) 7135 93193-50

E-Mail: info@renner-kompressoren.de
www.renner-kompressoren.de