Bent axis hydraulic motors

MXP Series
 Contents
M X P s e r i e s m o to r s
■■ Definition and main applications of hydraulic motors,
advantages of LEDUC motors. . . . . . . . . . . . . . . . . . . . 1 LEDUC hydraulic motors of the MXP series are of bent axis design,
with an angle of 40°. They combine high performance and reduced
■■ Operating conditions of motors. . . . . . . . . . . . . . . . . . . . 2 size envelope:
- global efficiency of over 90% (guaranteed in most applications);
■■ Determining the right motor. . . . . . . . . . . . . . . . . . . . . . 3
- suitable for use at operating speeds between 50 and 8,800 rpm;
■■ Range and characteristics . . . . . . . . . . . . . . . . . . . . . . . 4 - optimized weight and size.
Available in displacements from 12cc to 126cc, MXP motors are
■■ Efficiency curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
designed for applications on trucks or construction type equipment,
■■ Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 where intensive use is intermittent. (For heavy duty applications,
HYDRO LEDUC offers M and MSI series motors, literature available on
■■ ATEX certification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 request.)
MXP motors are designed for use in either closed or open loop
■■ Installation and start-up recommendations. . . . . . . . . . . 8 systems.
To ensure the best service life from your motors, please take care to
■■ Other LEDUC product lines. . . . . . . . . . . . . . . . . . . . . . 9
follow the installation and start-up recommendations (see pages 2
and 8).

HYDRO LEDUC also manufactures HYDRO LEDUC

a range of semi-integrated (plug-in) motors, the MSI series Head Office & Factory
and range of ISO flange motors: the M series type M. BP 9
Literature on request or on our website : F-54122 AZERAILLES (FRANCE)
www.hydroleduc.com Tél. +33 (0)3 83 76 77 40
Fax +33 (0)3 83 75 21 58
 A d v a nta ges o f M X P s e r i e s m o to r s

■■Definition of function

Hydraulic motors transform hydraulic flow into rotating speed and hydraulic
pressure into mechanical torque.
Motor rotating speed is proportional to the flow which is supplied to it.
Torque produced is proportional to the hydraulic pressure the motor receives.

■■Main applications of hydraulic motors

Typical applications are those requiring high torque within a small size.
The hydraulic motor is essential for rotations where:
-- mechanical solutions are complex or even impossible,
-- electrical or pneumatic power sources are not available,
-- environments are dangerous (i.e. risk of explosion or extreme temperatures).

■■Advantages of LEDUC motors

All structural components are made from similar materials resulting in consis-
tent thermal expansion and exceptional reliability.

No gears between plate

and rotating barrel yields
reduced noise levels. 1
Reinforced seals
to withstand back pressure
on motor drain return lines
up to 2.5 bar.

7 piston design, ensuring

excellent rotating smooth-
ness and constant torque.

High pressure oil injec-

tion on piston heads:
this reduces friction,
heat and wear.

Piston heads engaged

into barrel:
no risk of piston / plate
separation. Design and manufactured with
motor barrel and valve plate auto-
matically aligned. This guarantees
long service life (because no radial
mechanical stress).
 O pera ti n g co n d i ti o n s o f MX P se r ies m ot o r s

■■Hydraulic fluid ■■Rotating speeds

LEDUC motors are designed to be powered with mineral based hydraulic Minimum rotating speed to obtain continuous rotation is 200 rpm (however, in
fluid. Using other fluids is possible but may require a modified motor. Please certain conditions, the motor can run at speeds as low as 50 rpm).
contact us with details of fluid. Maximum rotating speed is given for each model of motor (see page 4).
Recommended viscosity:
-- Ideally : between 15 and 200 cSt; ■■Installation positions
-- Maximum range: between 5 and 1600 cSt.
LEDUC motors are made to operate in all positions.
■■Filtration of hydraulic fluid Important note : before start up, ensure the motor is filled with hydraulic fluid.
(See section on installation and start-up, page 8).
The service life of the motors depends greatly on the quality
and the cleanliness of the hydraulic fluid.
We recommend minimum cleanliness as follows:
-- NAS 1638 class 9
-- SAE class 6
-- IS0/DIS 4406 class 18/15.

■■Direction of rotation

The motors rotate clockwise or counter-clockwise depending on the direction of hydraulic flow entering the motor.

T1 T1

B A
CW rotation CCW rotation B
A

■■Drain pressure

It is essential to drain the motor (T1) to avoid excessive pressures on the shaft
seal.
Maximum acceptable internal pressure depends on motor rotating speed.

However, following these guidelines will avoid problems during operation:

-- maximum internal pressure (P int)
regardless of rotating speed (continuous): 2.5 bar (60psi);
-- maximum internal pressure (P int)
regardless of rotating speed (peak): 3 bar (80psi);
-- minimum pressure in the motor housing:
must be greater than ambient (external) pressure (P ext).
 De te rmi na t ion MX P se r ies m ot o r s

■■How to determine the correct motor for your application

Calculations using usual mechanical units:

N = rotating speed in rpm

C = torque in N.m
P = pressure supplied by the generator (hydraulic pump), in bar
ΔP = pressure difference between A and B, in bar
Disp. = displacement in cc
Q = flow in litres per minute
η = efficiency (%)

1. Torque supplied by the hydraulic motore

Disp. x ΔP
Theoretical torque = = Cth
20 π
Torque C = Cth x ηmotor

For example: a 50cc motor with a ∆P of 250 bar will supply a theoretical
torque of : 200 N.m.
Average global efficiency of the motor is 90%, actual torque is thus: 180 N.m

2. Rotating speed of the motor

The rotating speed of the hydraulic motor depends on the flow Q which goes
through it, and on the displacement of the motor.
Q
N= x 1000
Disp.

test bench for motors

3
■■Example

➀ Motor

➁ Variable displacement pump

➂ Pressure relief valve

➃ Valve

➄ Hydraulic motor

➅ Winch and load

The receiving organ (winch) ➅

needs to rotate at N = 400 rpm and supply an actual torque of 200 N.m.

The hydraulic pump ➀ is capable of operating at pressure P up to 350 bar.

1. Calculating the displacement of the hydraulic motor:
Disp. x ΔP
Cth = thus Disp. Cy = 35.9 cc In the LEDUC range,
20 π choose a motor with a displacement of 32 cc or 41 cc.
2. Calculating the flow Q which the pump needs to supply:
Corresponding flow :
Q
N= x 1000 thus Q = 14.36 l/min - for 32 cc motor, Q = 12.8 l/min
Disp.
- for 41 cc motor, Q = 16.4 l/min
 Range a nd cha r a cte r i s t ic s MX P se r ies m ot o r s

■■Characteristics of the MXP series motors

MXP series motors are designed for use on:

- truck equipment;
- construction equipment;
- agricultural machinery;
for intermittent service applications.
These motors are designed with a DIN interface.

Motor Max. allowable

continuous max. Intermittent max. Max. flow Torque max./min. pressure
Motor model
Displacement speed (1) speed(1) absorbed Torque bar at 350 bar temperature* continuous / peak
(cc) (rpm) (rpm) (l/mn) (m.N/bar) (m.N) (°C) (bar)
MXP12-092965 12 8000 8800 96 0.19 66 −25 / 110 400 / 450

MXP18-092890 18 8000 8800 144 0.28 98 −25 / 110 400 / 450

MXP25-092895 25 6300 6900 158 0.4 140 −25 / 110 400 / 450

MXP32-092900 32 6300 6900 202 0.5 175 −25 / 110 400 / 450

MXP41-092905 41 5600 6200 230 0.65 227 −25 / 110 400 / 450

MXP50-092910 50.3 5000 5500 252 0.8 280 −25 / 110 400 / 450

MXP63-092915 63 5000 5500 315 1 350 −25 / 110 400 / 450

MXP80-092925 80.4 4500 5000 362 1.27 445 −25 / 110 400 / 450

MXP108-092930 108.3 4000 4400 435 1.7 595 −25 / 110 400 / 450

MXP126-092970 126 3400 4400 428 2.0 700 −25 / 110 400 / 450

* for wider extreme temperatures, please contact us.

(1) for higher speeds, please contact us.
4 For special fluids, please contact us.

■■Acceptable forces applied to motor shaft

Fr : radial force measured at mid point of length of shaft.

Avoid having any radial or axial force on the shaft of MXP motors. If that is not
possible, please contact our Technical Department with details of application.

Motor model MXP 12 MXP 18 MXP 25 MXP 32 MXP 41 MXP 50 MXP 63 MXP 80 MXP 108 MXP 126

Fa (N/bar*) 15 20 30 30 40 40 50 60 80 90

* differential pressure between A and B.

For other forces, please contact us.

Fa
 DiEme
ffi nsion
ci e n cys MX P se r ies m ot o r s

■■Efficiency of motors f(displacement)

N of motor = 1000 rpm
ISO46 fluid at 25°C

MXP 12 - 18 MXP 25
% %
100 100

MXP 18 MXP 25
90 90
MXP 12

80 80

70 70

60 60

50 50
20 100 200 300 400 bar 20 100 200 300 400 bar

MXP 32 - 41 MXP 50 - 63
% %
100 100
MXP 63
MXP 41

90
MXP 32
90
MXP 50 5
80 80

70 70

60 60

50 50
20 100 200 300 400 bar 20 100 200 300 400 bar

MXP 80 - 108 MXP 126

% %
100 MXP 108 100
MXP 126
MXP 80
90 90

80 80

70 70

60 60

50 50
20 100 200 300 400 bar 20 100 200 300 400 bar
 Di me nsion s MX P se r ies m ot o r s

98
14.5 80
7 4 x  12.75

+
25.95 – 0.1
– 0.013

M12-6H
0

80
 80

40°
24
1,9 +– 0.1

B
+0.2
C
37.9 – 0.4

+0.2
55 – 0.4

drain G3/8”
Splines 8-32-36
DIN ISO 14 NF E 22.131
A
E
D
F

2xG F

View from F

Dis. weight
Motor model A B C D E F G
(cc) (kg)
MXP12-092965 12 171.5 71.9 103.9 197.9 108.5 54 G 3/4” 9.3

MXP18-092890 18 171.5 71.9 103.9 197.9 108.5 54 G 3/4” 9.3

MXP25-092895 25 171.5 71.9 103.9 197.7 108.5 54 G 3/4” 9.3

MXP32-092900 32 177.7 77 109.1 203.8 108.5 54 G 3/4” 10.3

MXP41-092905 41 177.7 77 109.1 203.8 108.5 54 G 3/4” 10.3

MXP50-092910 50,3 189.3 86.8 118.9 215.4 108.5 54 G 3/4” 11.5

MXP63-092915 63 189.3 86.8 118.9 215.4 108.5 54 G 3/4” 11.5

MXP80-092925 80,4 216.2 99.5 133.3 241.7 123.5 60 G 1” 14.5

MXP108-092930 108,3 216.2 99.5 133.3 241.7 123.5 60 G 1” 14.5

MXP126-092970 126 218.5 101.43 135.2 244 123.5 60 G 1” 14.5

 AT E X ce r ti fi ca t ion MX P se r ies m ot o r s

■■LEDUC motors can be certified ATEX; please consult us.

1 Dimensional control of MXP motor housing

2 Assembly of MXP motor
3 Spline cutting (shaft)
4 MXP motors
 I ns ta l l a ti o n a nd s ta rt - u p MX P se r ies m ot o r s

■■Maximizing service life of bearings

In cases where there is a radial force on motor shaft, keeping the direction
of that force within the shaded areas shown below will improve service life of
the motor.
For acceptable radial and axial forces, see page 4.

gear hub pulley hub

motor in rotation motor in rotation motor in rotation motor in rotation motor susceptible
CCW CW CW CCW of rotation
pressure in A pressure in B pressure in B pressure in A CCW et CW

70° 70° Fr 45° 45° Fr Fr

Fr Fr

B A B A B A B A B A

■■Mounting position of motors In installations where the position of the motor (H) is above the tank for the
drain return, be sure the drain line is always submerged in fluid.
LEDUC motors can be used in any position. If this is not the case, it is necessary to add a check valve on the drain line
following the figure below.
8

0.5 bar
ensure a ∆P of 0.3 to 0.5 bar

■■Operating conditions

See page 2.

■■Instructions for use

Each motor is supplied with an instruction leaflet,

also available via e-mail on request mail@hydroleduc.com.
 other product lines
XP
hydraulic motors
Fixed displacement
bent-axis pistons motors.
Models from 12 to 126 cc.
Available both in ISO
and SAE versions.

TXV PA
PAC
PAD

piston pumps
for trucks
HYDRO LEDUC offers 3 types of piston pumps perfectly
suited to all truck and PTO-mount applications.
Fixed and variable displacement from 12 to 150 cc.

micro-hydraulics
mobile and This is a field of exceptional
HYDRO LEDUC know-how:
industrial pumps • axial and radial piston pumps,
of fixed and variable displacement,
Fixed displacement pumps, the W series, and variable • axial piston micro-hydraulic motors,
displacement pumps, the DELTA series. High pressure • micro-hydraulic units incorporating
capabilities within minimal size. pump, electric motors, valving, controls,
W series: flanges to ISO 3019/2, shafts to DIN 5480. etc.
DELTA series: SAE shafts and flanges.
To users of hydraulic components which have to
be housed in extremely small spaces,
HYDRO LEDUC offers complete, original and reliable
solutions for even the most difficult environments.

we are passionate
about hydraulics…

hydro-pneumatic
accumulators
A dedicated R&D team means HYDRO LEDUC is able to adapt or create
Bladder, diaphragm accumulators.
products to meet specific customer requirements. Working in close
Spherical and cylindrical accumulators.
Volume capacities from 20 cc to 50 liters. cooperation with the decision-making teams of its customers, HYDRO LEDUC optimizes
Pressures up to 500 bar. proposals based on the specifications submitted.
Accessories for use with hydraulic accumulators.
 a passion for hydraulics

HYDRO LEDUC
Head Office & Factory
BP 9 - F-54122 AZERAILLES (FRANCE)
Tél. +33 (0)3 83 76 77 40
Fax +33 (0)3 83 75 21 58

HYDRO LEDUC GmbH

Haselwander Str. 5
D-77746 SCHUTTERWALD (DEUTSCHLAND)
Tel. +49 (0) 781-9482590
Fax +49 (0) 781-9482592

HYDRO LEDUC N.A., Inc.

19416 Park Row - Suite 170
HOUSTON, TEXAS 77084 (USA)
Tel. +1 281 679 9654
Fax +1 832 321 3553

Complete catalogues available at:

www.hydroleduc.com

The information is given as rough guide. Not contractual document. Cancels and replaces previous version.

HYDRO LEDUC

SAS with capital of 4 065 000 euros

Siret 319 027 421 00019

RC Nancy B 319 027 421

Editech.com

mail@hydroleduc.com

11/07/2012