Serie D1 - Cetop 3

Catalog HY14-2500/US Directional Control Valves
Introduction Series D1V
Application Operation
Series D1V hydraulic directional control valves are Series D1V directional control valves consist of a
A high performance, direct operated 4-way valves.
They are available in 2 or 3-position styles. They are
4-chamber style body, and a case hardened sliding
spool. The spool is directly shifted by a variety of
manifold mounted valves, which conform to NFPA’s operators including: solenoid, lever, cam, air or oil
D03, CETOP 3 mounting pattern. These valves pilots.
were designed for industrial and mobile hydraulic
applications which require high cycle rates, long life
and high efficiency.
D1VW Solenoid Operated Plug-In Conduit Box Style

• Easy access mounting bolts.
• Waterproof NEMA 4, IP67.
• No tools required for coil
removal.
• 19 standard spool styles
available.
• Four electrical connection
options.
• Lights included (CSA
approval for DC solenoids
and lights).
• Easy coil replacement.
• Plug-In design offered with
lights & other options.
D1VW Solenoid Operated Hirschmann (DIN) Style
• DIN Style (43650)

Hirschmann.
• 19 spool styles available.
removal.
• AC & DC lights available.
(CSA approval for solenoids
and lights).
D1VP Oil Pilot Operated
• Subplate pilot or end cap

pilot option.
• Pilot pressure:
15.2 Bar (220 PSI) to
207 Bar (3000 PSI).
D1.indd, dd
A2 Parker Hannifin Corporation

Hydraulic Valve Division
Elyria, Ohio, USA
Electrical Connections
Series D1V valves may be configured in all popular electrical configurations including:
Plug-in Conduit Box Explosion Proof Dual Spade (DC only)

A
DESINA (DC only) Hirschmann (DIN) Wire Lead Conduit Box
Deutsch (DC only) Metri-Pack (DC only)
D1VW Solenoid Operated Wire Lead Conduit Box Style

• Waterproof NEMA 4, IP67.
removal.
• 19 spool styles available.
• No lights available
D1VW Solenoid Operated DESINA Style
• Surge suppression standard.

• 19 standard spool available.
• No tools required for spool
removal.
• Wired to DESINA
Spec (VDMA).
• Lights included.
D1VW Solenoid Operated Dual Spade Style
• Dual spade connection

(SAE Style 1B).
• Surge suppression available.
• 19 standard spool styles
available.
D1.indd, dd

Elyria, Ohio, USA
Features • Low pressure drop.

• Easy access mounting bolts. • Phosphate finished body.
A • 345 Bar (5000 PSI) pressure rating. • CSA approved and U.L. recognized available.
• Flows to 22 GPM depending on spool. • Optional proportional spool available.
• Choice of five operator styles. • Optional painted body.
• Rugged four land spools.
D1VL Lever Operated
• Spring return or detent styles

available.
• Heavy duty handle design.
D1VA Air Operated
• Low pilot pressure

required –
4.1 Bar (60 PSI)
minimum.
D1VC Cam Operated
• Choice of 2 cam roller positions

(D1VC and D1VD).
• Two styles available
(D1VC and D1VG).
• Short stroke option.
D1.indd, dd

Elyria, Ohio, USA
D1VW AC Solenoid Operated Soft Shift

A
• 4 standard orifice
sizes available.
• 19 spool styles
available.
• AC Rectified or DC
input.
D1VW DC Solenoid Operated Soft Shift
D1.indd, dd

Elyria, Ohio, USA
Technical Information Series D1V
Standard Spool Reference Data
A
Maximum Flow, LPM (GPM)
350 Bar (5000 PSI) w/o Malfunction
High Watt Low Watt Low Watt
Model Spool Symbol DC AC DC
A B
D1V*001 78 (20) 49 (13) 37 (10)
P T
A B
D1V*002 78 (20) 45 (12) 68 (18)
P T
A B
D1V*003 70 (18) 30 (8) 34 (9)
P T
A B
D1V*004 37 (10) 30 (8) 68 (18)
P T
A B
D1V*005 60 (16) 45 (12) 45 (12)
P T
A B
D1V*006 79 (21) 49 (13) 52 (14)
P T
A B
D1V*007 45 (12) 18 (5) 18 (5)
P T
A B
D1V*008 49 (13) 45 (12) 37 (10)
P T
A B
D1V*009 58 (15) 45 (12) 45 (12)
P T
A B
D1V*010 13 (4) 11 (3) 15 (4)
P T
A B
D1V*011 58 (16) 30 (8) 37 (10)
P T
A B
D1V*014 45 (12) 18 (5) 18 (5)
P T
A B
D1V*015 79 (21) 30 (8) 34 (9)
P T
A B
D1V*016 60 (16) 45 (12) 52 (14)
P T
A B
D1V*020 78 (20) 45 (12) 75 (20)
P T
A B
D1V*026 37 (10) 11 (3) 7 (2)

P T
A B
D1V*030 70 (18) 18 (5) 75 (20)
P T
A B
D1V*081 32 (9) 26 (7) 30 (8)
P T
A B
D1V*082 32 (9) 26 (7) 34 (9)

P T
Center or De-energized position is indicated by P, A, B & T port notation.
D1.indd, dd

Elyria, Ohio, USA
D1VA, D1VP, D1VC, D1VL Reference Data
A
Maximum Flow, LPM (GPM) Maximum Flow, LPM (GPM)
350 Bar (5000 PSI) 350 Bar (5000 PSI)
Model Spool Symbol w/o Malfunction Model Spool Symbol w/o Malfunction
A B A B
D1V*1 83 (22) D1V*20 # 53 (14)
P T P T
A B A B
D1V*2 83 (22) D1V*26 # 11 (3)
P T P T
A B A B
D1V*4 45 (12) D1V*30 # 19 (5)
P T P T
A B A B
D1V*8 45 (12) D1V*81 30 (8)
P T P T
A B A B
D1V*9 57 (15) D1V*82 30 (8)

P T P T
Center or De-energized position is indicated by A, B, P & T port notation.

# D1VP only.
Manaplug – Electrical Mini Plug Desina – 12mm Connector

EP336-30 3 Pin Plug 5004109
EP316-30 5 Pin Plug (Double Solenoid)
EP31A-30 5 Pin Plug (Single Solenoid)
Monitor Switch Connector
1301903-N
Manaplug – Electrical Micro Plug
EP337-30 3 Pin Plug
EP317-30 5 Pin Plug (Double Solenoid)
EP31B-30 5 Pin Plug (Single Solenoid)
Electrical Cords – Mini Plug

EC 3 Conductor, 6 ft.
EC3 3 Conductor, 3 ft.
Quantity Required
A,C,D B,E,F H,K,M
Hirschmann – Female Connector
692915 Gray (Solenoid A) 1 – 1
692914 Black (Solenoid B) 1 1 –
Hirschmann – Female Connector-Rectified (48-240 VAC)

1301053 Gray (Solenoid A) 1 – 1
1301054 Black (Solenoid B) 1 1 –
Hirschmann – Female Connector-Rectified w/Lights (100-240 VAC)

1300712 2 1 1
Hirschmann – Female Connector w/Lights (Note Voltages)

694935 6-48 VAC or VDC 2 1 1
694936 48-120 VDC, 100-240 VAC 2 1 1
D1.indd, dd

Elyria, Ohio, USA
Solenoid Ratings Explosion Proof Solenoid Ratings*

Insulation System Class F U.L. & CSA (EU) Class I, Div 1 & 2, Groups C & D
A Allowable Deviation -15% to +10% for DC and AC rectified coils

from rated voltage -5% to +5% for AC Coils

Class II, Div 1 & 2, Groups E, F & G
As defined by the N.E.C.
Armature Wet pin type MSHA (EO) Complies with 30CFR, Part 18
CSA File Number LR60407 ATEX (ED) Complies with ATEX requirements for:
Exd, Group IIB; EN50014:
Environmental DC Solenoids meet NEMA 4 and IP67
1999+ Amds. 1 & 2, EN50018: 2000
Capability when properly wired and installed. Contact
HVD for AC coil applications. ATEX & CSA/US (ET) Complies with ATEX EN60079-0,
EN60079-1 Ex d IIC; CSA/US Ex d IIC,
AEx d IIC for Class I, Zone 1, UL1203,
UL1604, CSA E61241,1 Class II, Div 1
* Allowable Voltage Deviation ±10%.
Note that Explosion Proof AC coils are single frequency only.
Code
Voltage In Rush Amps In Rush Holding Amps Watts Resistance
Voltage Power Amperage VA @ 3MM
Code Code
D L 120 VDC N/A N/A 0.09 Amps 10 W 1584.00 ohms
D Omit 120 VDC N/A N/A 0.26 Amps 30 W 528.00 ohms
G Omit 198 VDC N/A N/A 0.15 Amps 30 W 1306.80 ohms
J L 24 VDC N/A N/A 0.44 Amps 10 W 51.89 ohms
J Omit 24 VDC N/A N/A 1.32 Amps 30 W 17.27 ohms
K L 12 VDC N/A N/A 0.88 Amps 10 W 12.97 ohms
K Omit 12 VDC N/A N/A 2.64 Amps 30 W 4.32 ohms
L L 6 VDC N/A N/A 1.67 Amps 10 W 3.59 ohms
L Omit 6 VDC N/A N/A 5.00 Amps 30 W 1.20 ohms
Q Omit 100 VAC / 60 Hz 2.05 Amps 170 VA 0.77 Amps 30 W 19.24 ohms
QD F 100 VAC / 60 Hz 1.35 Amps 135 VA 0.41 Amps 18 W 31.20 ohms
QD F 100 VAC / 50 Hz 1.50 Amps 150 VA 0.57 Amps 24 W 31.20 ohms
R F 24/60 VAC, Low Watt 6.67 Amps 160 VA 2.20 Amps 23 W 1.52 ohms
T Omit 240/60 VAC 0.83 Amps 199 VA 0.30 Amps 30 W 120.40 ohms
T Omit 220/50 VAC 0.87 Amps 191 VA 0.34 Amps 30 W 120.40 ohms
T F 240/60 VAC, Low Watt 0.70 Amps 168 VA 0.22 Amps 21 W 145.00 ohms
T F 220/50 VAC, Low Watt 0.75 Amps 165 VA 0.26 Amps 23 W 145.00 ohms
U L 98 VDC N/A N/A 0.10 Amps 10 W 960.00 ohms
U Omit 98 VDC N/A N/A 0.31 Amps 30W 288.00 ohms
Y Omit 120/60 VAC 1.7 Amps 204 VA 0.60 Amps 30 W 28.20 ohms
Y Omit 110/50 VAC 1.7 Amps 187 VA 0.68 Amps 30 W 28.20 ohms
Y F 120/60 VAC, Low Watt 1.40 Amps 168 VA 0.42 Amps 21 W 36.50 ohms
Y F 110/50 VAC, Low Watt 1.50 Amps 165 VA 0.50 Amps 23 W 36.50 ohms
Z L 250 VDC N/A N/A 0.04 Amps 10 W 6875.00 ohms
Z Omit 250 VDC N/A N/A 0.13 Amps 30 W 1889.64 ohms
Explosion Proof Solenoids
R 24/60 VAC 7.63 Amps 183 VA 2.85 Amps 27 W 1.99 ohms
T 240/60 VAC 0.76 Amps 183 VA 0.29 Amps 27 W 1.34 ohms
N 220/50 VAC 0.77 Amps 169 VA 0.31 Amps 27 W 1.38 ohms
Y 120/60 VAC 1.60 Amps 192 VA 0.58 Amps 27 W 33.50 ohms
P 110/50 VAC 1.47 Amps 162 VA 0.57 Amps 27 W 34.70 ohms
K 12 VDC N/A N/A 2.75 Amps 33 W 4.36 ohms
J 24 VDC N/A N/A 1.38 Amps 33 W 17.33 ohms
"ET" Explosion Proof Solenoids
K 12 VDC N/A N/A 1.00 Amps 12 W 12.00 ohms
J 24 VDC N/A N/A 1.00 Amps 13 W 44.30 ohms
Y 120/60-50 VAC N/A N/A 0.16 Amps 17 W 667.00 ohms
D1.indd, dd

Elyria, Ohio, USA
Performance Curves Series D1V
D1V Shift Limits, DC & AC Rectified 30 Watt
Example:
Determine the maximum allowable flow of a Series
Important Notes for Switching Limit Charts
D1V valve (#004 spool) at 138 Bar (2000 PSI) supply
1. For F & M style valves, reduce flow to 70% of that shown.
pressure. Locate the curve marked “004”. At 138 Bar 2. Shift limits charted for equal flow A and B ports. Unequal
(2000 PSI) supply pressure, the maximum flow is A and B port flows may reduce shift limits.
57 LPM (15 GPM). At 207 Bar (3000 PSI), the flow 3. These charts do not show explosion proof performance.
Consult factory for explosion proof duty.
is 49 LPM (13 GPM).
4. Blocking A or B ports will reduce flow by 70%.
D1VW*****L Shift Limits
D1.indd, dd

Elyria, Ohio, USA
Example:
57 LPM (15 GPM). At 207 Bar (3000 PSI), the flow is 3. These charts do not show explosion proof performance.
19 LPM (5 GPM).
D1.indd, dd

Elyria, Ohio, USA
Example:
42 LPM (11 GPM).
D1.indd, dd

Elyria, Ohio, USA
D1V Shift Limits, AC 30 Watt
A
PSI Bar
5000 345
003,004,
011,015
009
300
4000
021,022
Supply Pressure
250 010,026 007,014

001,002
3000
200
081,082 008
030
150 006
2000
100 005,016,020
1000
50
0
L/M 10 20 30 40 50 60 70 80 83
0
GPM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Flow
D1.indd, dd

Elyria, Ohio, USA
D1VW*****F Shift Limits, AC
Example:
68 LPM (18 GPM).
Soft Shift Limit Curves

DC Power Supply
D1.indd, dd

Elyria, Ohio, USA
Pressure Drop vs. Flow, D1VW Pressure Drop Reference Chart – 30 Watt Coil
High Watt
A
Curve Number
The table to the right provides Spool Shifted Center Condition
the flow vs. pressure drop No. P–A P–B B–T A–T (P–T) (B–A) (A–B) (P-A) (P-B) (A-T) (B-T)
curve reference for standard 001 3 3 2 2 — — — — — — —
and high performance D1V 002 2 2 1 1 2 1 1 1 1 1 1
Series valves by spool type. 003 2 2 1 1 — — — — — 1 —
The chart below demonstrates 004 2 2 1 1 — — — — — 2 2
graphically the pressure drop 005 2 3 1 1 — — — 5 — — —
characteristics of the standard 006 2 2 1 1 — 6 6 6 6 — —
D1VW*****F and the high 007 2 3 1 1 4 — 1 — — — —
performance D1V. The low watt 008 5 5 5 5 5 — — — — — —
coil and other design features 009 4 4 4 4 4 — — — — — —
of the standard D1VW*****F 010 3 3 — — — — — — — — —
accommodate a maximum flow 011 3 3 1 1 — — — — — 8 8
of 50 LPM (13 GPM) at
014 3 2 1 1 4 1 — — — — —
345 Bar (5000 PSI).
015 2 2 1 1 — — — — — — 1
016 3 2 1 1 — — — — 5 — —
020 4 4 2 2 — — — — — — —
026 4 4 — — — — — — — — —
030 2 2 1 1 — — — — — — —
081 7 7 8 8 — — — — — — —
082 7 7 8 8 — — — — — — —
Viscosity Correction Factor

Viscosity 75 150 200 250 300 350 400 Curves were generated using 100 SSU hydraulic oil.
(SSU) For any other viscosity, pressure drop will change per chart.
% of ∆P 93 111 119 126 132 137 141 Pressure drops charted for equal flow A and B ports.
(Approx.) Unequal A and B port flows may decrease shift limits.
Performance Curves – 30 Watt Coil
D1.indd, dd

Elyria, Ohio, USA
Pressure Drop vs. Flow, D1VW Pressure Drop Reference Chart – 10 Watt Coil
Low Watt Curve Number
The table to the right provides

Spool Shifted Center Condition
No. P–A P–B B–T A–T (P–T) (B–A) (A–B) (P-A) (P-B) (A-T) (B-T)
A
the flow vs. pressure drop
001 3 3 2 2 — — — — — — —
curve reference for 10 watt
002 2 2 1 1 2 2 2 2 2 1 1
D1V Series valves by spool
type. 003 3 3 2 1 — — — — — 4 —
004 3 3 1 1 — — — — — 6 6
The chart below demonstrates
005 3 3 1 1 — — — 7 — — —
graphically the pressure drop
006 3 3 1 1 — 8 8 7 7 — —
characteristics of the standard
D1VW*****L and the high 007 3 3 1 1 5 — 4 — — — 1
performance D1V. The low watt 008 5 5 6 6 7 — — — — — —
coil and other design features 009 6 6 6 6 5 — — — — — —
of the standard D1VW*****L 010 4 4 — — — — — — — — —
accommodate a maximum flow 011 3 3 1 1 — — — — — 11 11
of 50 LPM (13 GPM) at 014 3 3 1 1 4 — — 2 — 1 —
345 Bar (5000 PSI). 015 3 3 1 2 — — — — — — 4
016 3 3 1 1 — — — — 7 — —
020 7 7 4 4 — — — — — — —
026 6 6 — — — — — — — — —
030 2 2 1 1 — — — — — — —
081 9 9 10 10 — — — — — — —
082 10 10 10 10 — — — — — — —
Viscosity Correction Factor

Viscosity 75 150 200 250 300 350 400
(SSU)
% of ∆P 93 111 119 126 132 137 141
(Approx.)
Curves were generated using 100 SSU hydraulic oil.
For any other viscosity, pressure drop will change per chart.
Performance Curves – 10 Watt Coil
D1.indd, dd

Elyria, Ohio, USA
Catalog HY14-2500/US
Notes
D1.indd, dd

Elyria, Ohio, USA
Technical Information Series D1VW
General Description
Series D1VW directional control valves are high
performance, 4-chamber, direct operated, wet
armature solenoid controlled, 3 or 4-way valves.
B AB A A
They are available in 2 or 3-position and conform to
NFPA’s D03, CETOP 3 mounting patterns. PT
Features
• Soft shift available.
• 19 standard spool styles available (for other spools –
Consult Factory).
• Proportional spools.
• DC surge suppression.
• Eight electrical connection options.
• AC & DC lights available (CSA approval for solenoids and
lights).
• Internally ground.
• Waterproof (meets NEMA 4, up to IP67 on some models). • U.L. recognized available - Contact the division.
• Explosion proof. • No tools required for coil removal.
• CSA approvals. • AC rectified coils.
Specifications
Mounting Pattern NFPA D03, CETOP 3, NG 6 Leakage Rates* Maximum Allowable:
Mounting DIN 24340-A6 100 SSU @ 19.7 cc (1.2 Cu. in.) per Minute/Land @
Interface ISO 4401-AB-03-4-A 49°C (120°F) 69 Bar (1000 PSI)*
CETOP R35H 4.2-4-03, 73.8 cc (4.5 Cu. in.) per Minute/Land @
NFPA D03 207 Bar (3000 PSI)*
Maximum P, A, B *#008 and #009 Typical:
Pressure 345 Bar (5000 PSI) Standard Spools may 4.9 cc (0.3 Cu. in.) per Minute/Land @
207 Bar (3000 PSI) 10 Watt exceed these rates. 69 Bar (1000 PSI)*
CSA 276 Bar (3750 PSI) Consult Factory 26.2 cc (1.6 Cu. in.) per Minute/Land @
Tank: 345 Bar (5000 PSI)
103 Bar (1500 PSI) AC only
207 Bar (3000 PSI) DC/AC
Rectified Standard Response Time
207 Bar (3000 PSI) AC Optional Response time (milliseconds) at 345 Bar (5000 PSI) is
CSA 103 Bar (1500 PSI) 32 LPM (8.5 GPM).
Solenoid Type Pull-In Drop-Out
AC 13 20
DC 10 Watt 61 22
DC 30 Watt 51 21

Spool Center Condition
Orifice Closed Open 2-Position
Soft Shift Size Energize De-Energize Energize De-Energize Energize De-Energize
S2 0.020 125 ms 920 ms 200 ms 275 ms 51 ms 100 ms
S5 0.050 51 ms 675 ms 50 ms 27 ms 51 ms 21 ms
D1.indd, dd

Elyria, Ohio, USA
Ordering Information Series D1V
D 1V
A Directional Basic Valve

Control Valve
Actuator Spool Style Seal Solenoid Voltage
NFPA D03 Code Description Code Description Code Description Code Description
CETOP 3 W* Solenoid, N Nitrile A** 24/50 VAC Q** 100/60 VAC
DIN NG6 Wet Pin, V Fluorocarbon D 120 VDC QD† 100/60 - 100/50 VAC
Screw-in
E* EPR G 198 VDC R 24/60 VAC
HW* Reversed
* Contact HVD for J 24 VDC T 240/60 - 220/50 VAC
Wiring
availability. K 12 VDC U 98 VDC
* Valve schematic symbols are per NFPA/
L 6 VDC Y 120/60 - 110/50 VAC
ANSI standards, providing flow P to A when
energizing solenoid A. Note operators reverse N*** 220/50 VAC Z 250 VDC
sides for #008 and #009 spools. See installation P*** 110/50 VAC
information for details. To configure per DIN ** High Watt only
standards (A coil over A port, B coil over B port) *** Explosion Proof only.
code valves as D1VHW***. † Available in DIN only.
Code Symbol Code Symbol Code

Description Symbol
b A B
A B A B
B* Single solenoid, 2 position, spring offset.
001 011 P to A and B to T in offset position.
P T P T P T
b A B a
A B A B
C Double solenoid, 3 position,
002 014 spring centered.
P T
P T P T
b A B a
A B A B D† Double solenoid, 2 position, detent.
003 015
P T
P T P T
b A B
A B
A B
E Single solenoid, 2 position, spring centered.
004 016 P to B and A to T when energized.
P T
P T P T
b A B
A B A B
F‡ Single solenoid, 2 position. Spring offset,
005 020* energized to center. Position spool spacer on
P T P T A side. P to A and B to T in spring offset position. P T
A B A B A B a
006 026* H* Single solenoid, 2 position, spring offset.
P T P T P to B and A to T in offset position.
P T
A B A B
A B a
007 030** K Single solenoid, 2 position, spring centered.
P T P T P to A and B to T when energized.
P T
A B A B
00 8*, 081 M‡ Single solenoid, 2 position, spring offset,
A B a
009** P T energized to center position. Spool spacer on

P T
A B A B B side. P to B and A to T in spring offset position. P T
010 082
* 020, 026 and 030 spools only.
P T P T † 020 and 030 spools only.
* 008, 020 & 026 spools have closed crossover. ‡ High Watt only.
** 009 & 030 spools have open crossover.
Bold: Designates Tier I products and options.

Non-Bold: Designates Tier II products and options. These products will have longer lead times.
D1.indd, dd

Elyria, Ohio, USA
Ordering Information Series D1V
Solenoid Connection Coil

Options
Tube
Options
Manual
Override
Options
Electrical
Options
Shift
Response
and
Approvals Valve
Variations
Design
Series
NOTE:
A
Code Description Indication Not required
C* Leadwire Conduit Box when ordering.
D** Metric Plug (M12X1), Code Description
DESINA
Omit Standard Response
E† Explosion Proof
S2* Soft Shift, 0.020" Orifice
G†† Plug-In Conduit Box
J# Deutsch (DT06-2S)
M# Metri-Pack (150)
P DIN with Plug
I7** Monitor Switch Direct
S# Dual Spade Op. End Stroke
W† DIN w/o Plug I8** Monitor Switch
* No variations – See Plug-in. Direct Op. Start Stroke
** DC only, lights, diode surge * Not available with 10 watt. AC DIN
suppressor, not CSA approved. coil must include plug.
† Not available with lights. ** Single solenoid models only.
†† Required for variations on Not CE or CSA approved.
conduit box style. Must have
lights.
# DC only, no lights, not CSA
approved.
Code Description Code Description Code Description
Omit* High Watt Omit No Options Omit Standard Valve
D** Explosion Proof, J** Diode Surge 3*† CSA US
EEXD ATEX Suppressor 4*# CSA Canada
E** Explosion Proof, Z† Rectified Coil * Not available with AC
EEXME ATEX † DC tube standard. high pressure tube.
F† Low Watt ** DC only. DIN coil must † B, C, H styles only.
L†† 10 Watt have plug with lights. J, K, Y, U voltages only.
C, G, W sol. connections
O** Explosion Proof,
only. Conforms to UL429.
MSHA
# Valve is derated.
T# Explosion Proof,
Ex d IIC ATEX/CSA Code Description Code Description
U** Explosion Proof, Omit Standard Omit No Variations
UL/CSA T*† No Override 5** Signal Lights
* AC ambient temperature must P* Extended Manual Override 56* Manaplug (Mini) with Lights
not exceed 60°C (140°F). w/Boot
** 60 Hz only on AC, no options. 7B* Manaplug (Micro) with Lights
† AC only. * Manual override options not available 1C* Manaplug (Mini) Single Sol. 5-pin,
†† DC and AC rectified only. on explosion proof or soft shift. with Lights
# J, K and Y voltages only. Dual † DC/AC rectified only.
1D* Manplug (Micro) Single Sol. 5-pin,
frequency on AC, no options. with Lights
1M* Manaplug Opposite of Normal
Code Description
4D† Twist & Lock Override
Omit Standard Pressure (Old 5426, 33 Ford wiring)
103.5 Bar (1500 PSI) AC
Valve Weight: 4E† Push Manual Override (Old x5450)
207 Bar (3000 PSI) DC
Single Solenoid 1.36 kg (3.0 lbs.) 4F Heavy Duty Detent
H* High Pressure, AC only
Double Solenoid 1.6 kg (3.5 lbs.) 207 Bar (3000 PSI) 1P Painted Body
Standard Bolt Kit: BK209 * Not available with CSA. 7Y* 4-pin M12x1 Manaplug,
Metric Bolt Kit: BKM209 special wiring with lights (Old B755)
Seal Kit: * Plug-in Conduit Box
Nitrile SKD1VWN91 ** Plug-in, DIN, or DESINA only
Fluorocarbon SKD1VWV91 † DC/AC Rectified only.
Not available with soft shift.
D1.indd, dd

Elyria, Ohio, USA
Dimensions Series D1V
Inch equivalents for millimeter dimensions are shown in (**)
DC Plug-In Conduit Box Connector,

A with Lights, Double Solenoid
Note: 22.0 mm (0.87") from bottom of bolt hole counterbore to bottom of valve.
DC Plug-In or Leadwire Conduit Box Connector,

with or without Lights, Single Solenoid
D1.indd, dd

Elyria, Ohio, USA
DC DIN with Plug Connector, Double Solenoid

“P” Option Shown A
DC DIN Connector, Single Solenoid

“P” Option Shown
D1.indd, dd

Elyria, Ohio, USA
AC Leadwire Conduit Box Connector,

A without Lights, Double Solenoid, “C” Option
AC Leadwire Conduit Box Connector,

without Lights, Single Solenoid, “C” Option
D1.indd, dd

Elyria, Ohio, USA
AC Plug-in Conduit Box Connector,

with Lights, Double Solenoid, “G” Option A
DC Plug-in or Leadwire Conduit Box Connector, with or without Lights

and Extended Override Tubes, Double Solenoid
D1.indd, dd

Elyria, Ohio, USA
DC Deutsch Connector, Double Solenoid

A
DC Deutsch Connector, Single Solenoid
D1.indd, dd

Elyria, Ohio, USA
DC Desina Connector, Double Solenoid

A
87.8
(3.46)
DC Desina Connector, Single Solenoid
D1.indd, dd

Elyria, Ohio, USA
Explosion Proof, Ex d IIC ATEX/CSA, Double Solenoid

A
Explosion Proof, Ex d IIC ATEX/CSA, Single Solenoid
D1.indd, dd

Elyria, Ohio, USA
Explosion Proof U.L. & C.S.A., Double Solenoid
t
Note: A
u
163.7 2 black wires
(6.44) 18 Inch Lead 1 green wire
O
60.4
(2.38) Wires Standard
e
1/2" NPT
a s
94.4
(3.72)
130.8
(5.15)
P h 304.4
(11.98)
46.0
(1.81)
73.0 (2.87)
15.1 (0.61)
7.5 (0.30)
Explosion Proof M.S.H.A., Double Solenoid
3/4-20 UNF 163.7

Thd. 60.4 (6.44)
3/4-20 UNF
(2.38) 38.0 (1.50)
Thd.
113.0
(4.45)
130.8 15.51 (0.61)

(5.15) 7.5 (0.30)
304.4 46.0
(6.44) (1.81)
73.0 (2.87)
Explosion Proof, EEXD ATEX, Double Solenoid

74.7 (2.94)
69.9 (2.75)
19.4 M20 x 1.5-6H Thd.
(0.76) 15.5 Ground Stud with Lockwasher
(0.61)
131.7
(5.19)
100.9
(3.97) 100.6
(3.96)
42.8
(1.69)
7.5 (0.30)
141.0 (5.55)
46.0 (1.81)
73.5 (2.89) 324.7 (12.78)
D1.indd, dd

Elyria, Ohio, USA
DC Plug-in or Leadwire Conduit Box with Monitor Switch,

A with or without Lights, Single Solenoid
Monitor Switch
(Variation I7 and I8)
This feature provides for electrical confirmation of
the spool shift. This can be used in safety circuits,
to assure proper sequencing, etc.
Switch Data
Inductive switch requiring +18-42 volt input.
Outputs “A” and “B” are opposite; one at “0”
voltage, the other at input voltage. During
switching, “A” and “B” outputs reverse. Provides
0.4A switching current.
For repetitive switch power-up conditions, please consult factory.
D1.indd, dd

Elyria, Ohio, USA
Accessories Series D1V
Manaplug (Options 56 & 1C) Micro Connector Options (7B & 1D)
Interface – Brad Harrison Plug

– 3-Pin for Single Solenoid
– 5-Pin for Double Solenoid
A
Ground
Wire #1 (Green)
Solenoid (Negative)
Solenoid (Positive)
Wire #3 (Red/Black)
Wire #2 (Red/White)
3-Pin Manaplug (Mini) with Lights
Single Solenoid Valves – Installed Opposite Side of Solenoid
Pins are as seen on valve (male pin connectors)
Conduit Box Option C Signal Lights (Option 5) — Plug-in Only

– No Wiring Options Available – LED Interface
– Meets Nema 4/IP67
Hirschmann Plug with Lights (Option P5) DESINA Connector (Option D)

ISO 4400/DIN 43650 Form “A” M12 pin assignment
Pin #3 Standard
(Ground) DESINA – design
Pin 1 and 2
connected
Pin #1 1 = Not used
Pin #2
(Negative)
4 1
2 = Not used
(Positive) 2
3 = 0V
3
4 = Signal (24 V) 1 3
5 = Earth Ground
4
5
2 5
Face View of Plug
Pins are as seen on valve (male pin connectors)

D1.indd, dd

Elyria, Ohio, USA
Accessories Series D1V
Mounting Bolt Kits
A Bolt Kits for use with D1V Directional Control Valves, "ET" Explosion Proof & Sandwich Valves
(D1V*-91, 82 & 70/75 Design, Solenoid Operated & D1V*-72 Design, Non-Solenoid Operated)
Number of Sandwich Valves @40mm (1.58") thickness
0 1 2 3 4
BK209 1.25 in. BK243 2.88 in. BK225 4.38 in. BK244 6.00 in. BK245 7.50 in.
0
BKM209 30 mm BKM243 70 mm BKM225 110 mm BKM244 150 mm BKM245 190 mm
Number of Sandwich Valves at
BK246 3.00 in. BK247 4.62 in. BK248 6.12 in. BK249 7.75 in.
44.5mm (1.75") Thickness
1
BKM246 75 mm BKM247 115 mm BKM248 155 mm BKM249 195 mm
BK250 4.75 in. BK251 6.38 in. BK252 7.88 in.
2
BKM250 120 mm BKM251 160 mm BKM252 200 mm
BK253 6.50 in. BK254 8.12 in.
3
BKM102 170 mm BKM254 205 mm
BK103 8.25 in.
4
BKM103 210 mm
Note: All bolts are SAE Grade 8, 10-24 UNC 2A thread (Metric-M5-0.8)
Torque to 5.6 Nm (50 in-Lb).
Bolt Kits for use with D1V Directional Control Valves with Explosion Proof Coils & Sandwich Valves
(D1V*-91, 82 & 70/75 Design) Except "ET" Coil
Number of Sandwich Valves @40mm (1.58") thickness
0 1 2 3 4
BK50 2.00 in. BK211 3.63 in. BK101 5.12 in. BK102 6.75 in. BK103 8.25 in.
0
BKM50 50 mm — BKM101 130 mm BKM102 170 mm BKM103 210 mm
Number of Sandwich Valves at
BK51 3.75 in. BK212 5.37 in. BK105 6.87 in. BK106 7.75 in.
44.5mm (1.75") Thickness
1
BKM51 95 mm — BKM105 180 mm BKM106 195 mm
BK52 5.50 in. BK213 7.13 in. BK108 8.62 in.
2
BKM52 140 mm — BKM108 220 mm
BK53 7.25 in. BK214 8.87 in.
3
BKM53 185 mm —
BK54 9.00 in.
4
BKM54 230 mm
Note: All bolts are SAE Grade 8, 10-24 UNC 2A thread (Metric-M5-0.8)
Torque to 5.6 Nm (50 in-Lb).
Sandwich Valve Dimensional Data

All D03 Sandwich valves (starting with 31 Series) including CM2, CPOM2, FM2, PRDM2 and RM2 measure
40mm (1.58") thickness.
For additional technical information about Sandwich valves, refer to the Sandwich Valve Section of this Catalog.
D1.indd, dd

Elyria, Ohio, USA
Technical Information Series D1VA, D1VP
General Description
Series D1VA and D1VP directional control valves are B AB A
high performance, 4 and 5-chamber, direct operated,
air and oil pilot controlled, 3 or 4-way valves. They are P T
A
available in 2 or 3-position and conform to NFPA’s
D03, CETOP 3 mounting patterns. B AB A
Features P T
• Low pilot pressure required.
D1VA – 4.1 Bar (60 PSI) minimum
D1VP – 15.2 Bar (220 PSI) minimum
Air Operated
Shift Volume. The air pilot chamber requires a volume
of 1.8 cc (.106 in.3) for complete shift from center to
end.
Pilot Piston. The pilot piston area is 506 mm2 (.785
in.2). Pilot piston stroke is 3.4 mm (.135 in.).
Response Time. Response time will vary with pilot
line size, pilot line length, pilot pressure, air control
valve shift time and air valve flow capacity (Cv). Specifications
Mounting Pattern NFPA D03, CETOP 3, NG 6
Oil Operated Operating: 345 Bar (5000 PSI)
Maximum
Shift Volume. The hydraulic pilot chamber requires Pressure Tank Line: D1VA 34 Bar (500 PSI)
a volume of 0.7 cc (.042 in.3) for complete shift from D1VP 207 Bar (3000 PSI)
center to end. Maximum Flow See Reference Data
Pilot Piston. The hydraulic piston area is 198 mm2 D1VA:
Air Minimum 4.1 Bar (60 PSI)
(.307 in.2). Pilot piston stroke is 3.4 mm (.135 in.).
Pilot Pressure Air Maximum 10.2 Bar (150 PSI)
Response Time. Response time will vary with pilot D1VP:
line size, pilot line length, pilot pressure, pilot valve Oil Minimum 15.2 Bar (220 PSI)
shift time and oil valve flow capacity (GPM). Oil Maximum 207 Bar (3000 PSI)
Dimensions – Inch equivalents for millimeter dimensions are shown in (**)

Oil Operated D1VP, Single and Double Pilot
51.0
(2.00)
min.
40.5
(1.60)
23.0
Y
(0.91)
15.5 9.0
42.0 1/4 BSPP (90) (0.35)
(1.65) (0.61) 43.0 22.0
or (1.70) (0.87)
16.9
min.
(0.67)
SAE #4
3.3 (0.13) max.

50.0 X & Y Ports
(1.97) 0.56
See (0.022)
Note
127.0 46.0 23.8

(5.13) (1.81) (0.94)
Note: 22.0 mm (0.87”) from bottom of bolt hole counterbore to bottom of valve.
D1.indd, dd

Elyria, Ohio, USA
Ordering Information Series D1VP
D 1V P
A Directional
Control
Valve
Basic
Valve
Actuator Spool Style Seal Variations Design
Series
NOTE:
Not required
when ordering.
NFPA D03 Code Description

CETOP 3 Omit Standard
P10* Monitor Switch
4F Heavy Duty Detent
Oil 90 BSPP Threads
Operator * Not available on C and D styles.
Not CE or CSA approved.
Code Description
Code Symbol N Nitrile
A B V Fluorocarbon
001
P T
A B
002
Code
Description Symbol
P T
A B Single operator, two position
004 B# spring offset.
P to A and B to T in offset position.
P T
A B Double operator,
008* C three position,
P T
spring centered.
A B
D Double operator,
009**
two position, detent.
P T
A B Two position, spring centered.
020* E# P to B and A to T
P T in shifted position.
A B Single operator, two position,
026* H# spring offset. P to B and A to T
P T in offset position.
A B Two position, spring centered.
030** K# P to A and B to T
P T in shifted position.
A B
# D available with 020 and 030 spools only.
081 B & H available with 020, 026 and 030 spools only.
P T E & K not available with 020, 026 and 030 spools.
A B
082 This condition varies

Valve schematic symbols are per with spool code.
P T
NFPA/ANSI standards, providing
flow P to A when energizing * 008, 020 and 026 spools
operator X. Note operators reverse have closed crossover.
Valve Weight: 1.90 kg (4.2 lbs.)
sides for #008 and #009 spools. ** 009 and 030 spools have
See installation information for Standard Bolt Kit: BK209 10–24x1.25
open crossover.
details. Metric Bolt Kit: BKM209 M5–0.8x30mm
Seal Kit:
Nitrile SKD1VP
Fluorocarbon SKD1VPV

D1.indd, dd

Elyria, Ohio, USA
Ordering Information Series D1VA
D 1V A
Directional
Control
Valve
Basic
Valve
Actuator Spool Style Seal Variations Design
Series
NOTE:
A
Not required
when ordering.

CETOP 3 Omit Standard
Air P10* Monitor Switch
Operator 90 1/4 BSPP Threads
* Not available on C & D
styles.
Not CE or CSA approved.
Code Symbol
Code Description
A B
001 N Nitrile
V Fluorocarbon
P T
A B
002
P T Code
Description Symbol
A B
Single operator, two position b A B
004 B spring offset.
P T P to A and B to T in offset position. P T
A B
Double operator, b A B a
008* C three position,
P T spring centered. P T
A B
b A B a
009** D Double operator,
two position, detent.
P T
P T
A B
b A B
Two position, spring centered.
081
E P to B and A to T
P T in shifted position. P T
A B A B a
Single operator, two position,
082
H spring offset. P to B and A to T
P T in offset position. P T
A B a
* 008 spool has closed Two position, spring centered.
crossover. K P to A and B to T
** 009 spool has open in shifted position. P T
crossover.
Valve schematic symbols are per NFPA/
energizing operator A. Note operators reverse
sides for #008 and #009 spools. See installation This condition varies
information for details. with spool code.

Standard Bolt Kit: BK209 10–24x1.25
Metric Bolt Kit: BKM209 M5–0.8x30mm
Grade 8 bolts required
Seal Kit:
Nitrile SKD1VA
Fluorocarbon SKD1VAV

D1.indd, dd

Elyria, Ohio, USA
Dimensions Series D1VA
A Air Operated D1VA, Double Pilot
117.8 (4.64)
61.6
104.55 (4.12)
(2.43)
1/8 NPT Typ.

or
18-28 BSPP
38.5
192.5 (1.52)
(7.58)
51.95
(2.05)
23.8
(0.94)
23.0 (0.91)
46.0
Note: 22.0 mm (0.87") from bottom of bolt (1.81)
hole counterbore to bottom of valve.
Air Operated D1VA, Single Pilot
Note: 22.0 mm (0.87") from bottom of bolt

D1.indd, dd

Elyria, Ohio, USA
Technical Information Series D1VC, D1VD, D1VG
General Description
Series D1VC, D1VD and D1VG directional control
valves are high performance, 4-chamber, direct
operated, cam controlled, 4-way valves. They are
A
available in 2-position and conform to NFPA’s D03,
CETOP 3 mounting patterns.
Features
• Choice of 2 cam roller positions (D1VC and D1VD)
• Two styles available (D1VC and D1VG)
• Short stroke option
Specifications
Maximum Operating: 345 Bar (5000 PSI)
Pressure Tank Line: 34 Bar (500 PSI)
Nominal Flow 32 LPM (8.5 GPM)
Maximum Flow See Reference Data
Force Required D1VC, D1VD: 107 N (24 lbs.)
to Shift D1VG: 36 N (8 lbs.)
Maximum
Cam Angle 30°
Ordering Information
D 1V
Directional Basic Actuator Spool Style Seal Variations Design
Control Valve Series
Valve NOTE:
Not required
NFPA D03 Code Symbol Code Description when ordering.
CETOP 3 A B N Nitrile
001 V Fluorocarbon
P T
A B
Code Description
002
P T
Omit Standard
A B P05 Short Stroke
004 P10* Monitor Switch
Code Description
P T * Not CE or CSA approved.
C Cam (90° to A B
mounting surface)
008* Code Description Symbol
D Cam parallel to
mounting surface
P T
Two position, A B
G Cam Lever
A B B spring offset operator
009† at “A” port end. P T
P T Two position, A B
A B H spring offset operator
081 at “B” port end. P T
Valve Weight: Type C & D 1.44 kg (3.2 lbs.) P T
Type G 1.6 kg (3.7 lbs.) Valve schematic symbols are per NFPA/
A B
Standard Bolt Kit: BK209 1–24x1.25 ANSI standards, providing flow P to A when
082
energized. Note flow paths reverse sides for
Metric Bolt Kit: BKM209 M5–0.8x30mm P T #008 and #009 spools.
Seal Kit:
* 008 spool has closed crossover.
Nitrile SKD1VC
† 009 spool has open crossover.
Fluorocarbon SKD1VCV
D1.indd, dd

Elyria, Ohio, USA
Dimensions Series D1VC, D1VD, D1VG
Cam Operated D1VC and D1VD

A Full
Valve Type Pre-Travel Spool Over-Travel
Travel
Standard 2.00 9.06 2.03
Valve (0.079) (0.357) (0.080)
P05 0 7.06 4.03
Short Stroke (0) (0.278) (0.159)
38.5 38.4
Over-Travel (1.51)
(1.52) Full Spool Travel
Pre-Travel
Note: For D1VD,

52.0 Cam Rotated 90°
(2.05)
23.8
(0.94)
165.9 23.0 (0.91)

(6.53) 46.0
(1.81)
Cam Lever Operated D1VG

Full
Valve Type Pre-Travel Spool Over-Travel
Travel
Standard 6.95 39.63 10.00
Valve (0.27) (1.56) (0.39)
P05 0 30.12 18.40
Short Stroke (0) (1.19) (0.72)
Over-Travel
Full Spool Travel
Pre-Travel 38.5
(1.52)
38.5
(1.52)
79.1
(3.11)
52.0
(2.05)
See 23.8
Note (0.94)
209.7 23.0 (0.91)

(8.26) 46.0
(1.81)
D1.indd, dd

Elyria, Ohio, USA
Technical Information Series D1VL
General Description
Series D1VL directional control valves are high-
performance, 4-chamber, direct operated, lever
controlled, 4-way valves. They are available in 2 or
A B A
3-position and conform to NFPA’s D03, CETOP 3
mounting patterns. P T
Features
• Spring return or detent styles available
• Heavy duty handle design
Specifications
Maximum Operating: 345 Bar (5000 PSI)
Pressure Tank Line: 34 Bar (500 PSI)
Maximum Flow See Reference Data
Force Required
to Shift Lever 25 N (5.6 lbs)
Operator
Dimensions
Lever Operated D1VL
15.5
8.9° (0.61)
85.5 Full Shift
(3.37) 15.5
(0.61)
150.6
38.6 (5.93)
(1.52)
50.0
46.0 (1.97)
(1.81) 23.8
See
Note (0.94)
149.5 23.0
(5.89) (0.91)
46.0
(1.81)
D1.indd, dd

Elyria, Ohio, USA
Ordering Information Series D1VL
D 1V
A Directional
Control
Valve
Basic
Valve
Operator
Type and Location
Spool Style Seal Variations Design
Series
NOTE:
Not required
when ordering.

CETOP 3
Omit Standard
P10* Monitor Switch
* Not available on C,D or
N styles. Not CE or CSA
Operator Location (A or B Port End) approved.
Code Operator Type For Valve Style
B C D E H K N
L Lever (Standard) B B B A B B B Code Description
LB Lever (Alternate) A A A N/A A N/A A N Nitrile
V Fluorocarbon
Code Symbol Code

Description Symbol
A B
Two position, spring offset. A B
001 B P to A and B to T in offset
P T position. P T
A B A B
002 C Three position,
P T spring centered. P T
A B A B
004 D Two position, detent.
P T P T
A B
Two position, spring centered. A B
008* E P to B and A to T
P T in shifted position. P T
A B A B
Two position, spring offset.
009† H P to B and A to T
P T in offset position. P T
A B A B
Two position, spring centered.
081*
K P to A and B to T
P T
in shifted position. P T
A B
A B
082
N Three position, detent.
P T
P T
* 008 and 081 spools have

This condition varies
closed crossover.
with spool code.
† 009 has open crossover.
Valve schematic symbols are per NFPA/

energizing operator A. Note flow paths reverse
sides for #008 and #009 spools in three Standard Bolt Kit: BK209 10–24x1.25
position valves. Metric Bolt Kit: BKM209 M5–0.8x30mm
Grade 8 bolts required
Seal Kit:
Nitrile SKD1VL
Fluorocarbon SKD1VLV

D1.indd, dd

Elyria, Ohio, USA
Installation Information Series D1V
Fluid Recommendations Flow Path Data

Premium quality hydraulic oil with a viscosity range
between 32-54 cst. (150-250 SSU) at 38°C (100°F) is
recommended. The absolute operation viscosity range
D1V
Operator A Operator B
A
is from 16-220 cst. (80-1000 SSU). Oil should have
maximum anti-wear properties and rust and oxidation
treatments.
*Note: On valves with 008 or 009 spool, A and/or B operators
Fluids and Seals reverse sides. Flow paths remain the same as viewed from
top of valve.
Valves using synthetic, fire-resistant fluids require
special seals. When phosphate ester or its blends are Single Pass Operation
used, fluorocarbon seals are required. Water- Valve flow ratings are for double pass operation
glycol, (95/5) water-in-oil emulsions, and petroleum oil (with equal flow in both paths). When using these
may be used with NITRILE seals. components in single pass applications, flow
Temperature Recommendation capabilities may be reduced. Consult your local Parker
representative for details.
Recommended oil temperature:
-29°C to +71°C (-20°F to +160°F) Double Solenoid. With solenoid “A” energized,
flow path is P→A and B→T. When solenoid “B” is
Ambient temperature:
energized, flow path is P→B and A→T. The center
AC High Watt ambient temperature cannot exceed condition on a spring-centered valve exists when both
60°C (140°F). coils are de-energized, or during a complete shift, as
DC High Watt, DC Low Watt and AC Low Watt ambient the spool passes through center.
temperature cannot exceed 71°C (160°F). Detent and Spring Offset. The center condition exists
on detent and spring offset valves only during spool
Filtration crossover. To shift and hold a detented spool, only a
For maximum valve and system component life, the momentary energizing of the solenoid is necessary.
system should be protected at a contamination level The minimum duration of the signal is approximately
not to exceed 125 particles greater than 10 microns 0.1 seconds for DC voltages. This position will be held
per milliliter of fluid. (SAE Class 4 or better, ISO Code provided the spool center line is in a horizontal plane,
16/13). and no shock or vibration is present to displace the
spool.
Tank Line Surges
Single Solenoid. Spring offset valves can be ordered
If several valves are piped with a common tank line,
in styles B, E, F, H, K and M. Flow path data for the
flow surges in the line may cause unexpected spool
various styles are described in the order chart.
shift. Detent style valves are most susceptible to this.
Separate tank lines should be used when line surges
Electrical Failure
are expected in an application.
Should electric power fail, spring offset and spring
Recommended Mounting Position centered valves will shift to the spring held position.
Detented valves will stay in the last position held
Valve Type Recommended Mounting Position before power failure. If main flow does not fail or stop
Detent (Solenoid) Horizontal simultaneously, machine actuators may continue to
Spring Centered Unrestricted function in an undesirable manner or sequence.
Spring Offset Unrestricted
Torque Specifications
Silting Torque values recommended for the bolts which mount
Silting can cause any sliding spool valve to stick the valve to the manifold or subplate are as follows:
and not spring return, if held shifted under pressure #10-24 thread (M5-0.8) torque 5.6 Nm (50 in-lbs).
for long periods of time. The valve should be cycled
periodically to prevent sticking.
D1.indd, dd

Elyria, Ohio, USA
Installation Information Series D1V
Mounting Pattern — NFPA D03, CETOP 3, NG 6

A 51.00
(2.000) M5-0.8 (10-24) UNC-2B thread
min. x 10.40 (.410) min. thread depth
40.50
(1.594) 4-holes
0.28
33.00
(0.011) S A B
(1.300)
30.20
5.10 (1.190)
(0.200)
21.50
(0.850)
0.75
(0.030) B
O 7.5 (.295) max.
A P.A.B. & T ports
T 0.56
15.50 (0.022)
L A B
31.00 (0.610)
43.00 (1.220)
(1.70) A
min.
25.90
(1.020) O 3.86/4.27 (.152/.168)
31.75 B x 4.00 (.160) min. depth
(1.250)
0.28
(0.011) S A B
P
12.70
(0.500)
4.80 (0.190) R. max. typ.
4 places
D1.indd, dd

Elyria, Ohio, USA

Serie D1 - Cetop 3

Uploaded by

Copyright:

Available Formats

Serie D1 - Cetop 3

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Serie D1 - Cetop 3

Uploaded by

Copyright:

Available Formats

Catalog HY14-2500/US Directional Control Valves

Introduction Series D1V

D1VW Solenoid Operated Plug-In Conduit Box Style

D1VW Solenoid Operated Hirschmann (DIN) Style

• DIN Style (43650)

D1VP Oil Pilot Operated

• Subplate pilot or end cap

A2 Parker Hannifin Corporation

Plug-in Conduit Box Explosion Proof Dual Spade (DC only)

D1VW Solenoid Operated Wire Lead Conduit Box Style

• Easy access mounting bolts.

D1VW Solenoid Operated DESINA Style

• Surge suppression standard.

D1VW Solenoid Operated Dual Spade Style

• Dual spade connection

A3 Parker Hannifin Corporation

Features • Low pressure drop.

D1VL Lever Operated

• Spring return or detent styles

D1VA Air Operated

• Low pilot pressure

D1VC Cam Operated

• Choice of 2 cam roller positions

A4 Parker Hannifin Corporation

D1VW AC Solenoid Operated Soft Shift

D1VW DC Solenoid Operated Soft Shift

A5 Parker Hannifin Corporation

Standard Spool Reference Data

D1V*026 37 (10) 11 (3) 7 (2)

D1V*082 32 (9) 26 (7) 34 (9)

Center or De-energized position is indicated by P, A, B & T port notation.

A6 Parker Hannifin Corporation

D1VA, D1VP, D1VC, D1VL Reference Data

D1V*9 57 (15) D1V*82 30 (8)

Center or De-energized position is indicated by A, B, P & T port notation.

Manaplug – Electrical Mini Plug Desina – 12mm Connector

Electrical Cords – Mini Plug

Hirschmann – Female Connector-Rectified (48-240 VAC)

Hirschmann – Female Connector-Rectified w/Lights (100-240 VAC)

Hirschmann – Female Connector w/Lights (Note Voltages)

A7 Parker Hannifin Corporation

Solenoid Ratings Explosion Proof Solenoid Ratings*

A Allowable Deviation -15% to +10% for DC and AC rectified coils

A8 Parker Hannifin Corporation

D1V Shift Limits, DC & AC Rectified 30 Watt

D1VW*****L Shift Limits

A9 Parker Hannifin Corporation

D1V Shift Limits, DC & AC Rectified 30 Watt

D1VW*****L Shift Limits

A10 Parker Hannifin Corporation

D1V Shift Limits, DC & AC Rectified 30 Watt

D1VW*****L Shift Limits

A11 Parker Hannifin Corporation

D1V Shift Limits, AC 30 Watt

250 010,026 007,014

A12 Parker Hannifin Corporation

D1VW*****F Shift Limits, AC

Soft Shift Limit Curves

A13 Parker Hannifin Corporation

D1V9 57 (15) D1V82 30 (8)