MA1608-EB © 2016 CASIO COMPUTER CO., LTD.

Operation Guide 5478

ENGLISH
Congratulations upon your selection of this CASIO watch.

To ensure that this watch provides you with the years of service for which it is
designed, carefully read and follow the instructions in this manual, especially the
information under “Operating Precautions” and “User Maintenance”.
Be sure to keep all user documentation handy for future reference.

E-1

About This Manual Things to check before using the watch

x Depending on the model of your watch, display text 1. Check the Home City and the daylight saving time (DST) setting.
appears either as dark figures on a light background, or
light figures on a dark background. All sample displays Use the procedure under “To configure Home City settings” (page E-18) to configure
in this manual are shown using dark figures on a light your Home City and daylight saving time settings.
background. Important!
x Button operations are indicated using the letters shown x Proper World Time Mode data depends on correct Home City, time, and date
in the illustration. settings in the Timekeeping Mode. Make sure you configure these settings
x Note that the product illustrations in this manual are correctly.
intended for reference only, and so the actual product
may appear somewhat different than depicted by an 2. Set the current time.
illustration.
x See “Adjusting the Digital Time and Date Settings” (page E-21).
The watch is now ready for use.

E-2 E-3

Contents Using the Stopwatch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-25

To enter the Stopwatch Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-26
About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-2 To perform an elapsed time operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-28
Things to check before using the watch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-3 To pause at a split time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-28
To measure two finishes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-28
Mode Reference Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-8
To set a target time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-30
Timekeeping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-17 To use the target time alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-31
To stop the alert beeper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-35
Configuring Home City Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-18
To perform stopwatch timing without using the Target Time Alarm . . . . . . . . . E-35
To configure Home City settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-18
To change the Daylight Saving Time (summer time) setting . . . . . . . . . . . . . . E-20 Countdown Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-36
To enter the Countdown Timer Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-36
Adjusting the Digital Time and Date Settings . . . . . . . . . . . . . . . . . . . . . . . . . E-21
To configure the countdown timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-37
To configure the digital time and date settings . . . . . . . . . . . . . . . . . . . . . . . . E-21
To perform a countdown timer operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-38

E-4 E-5

To stop the alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-39 Illumination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-48

To turn on illumination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-48
Checking the Current Time in a Different Time Zone . . . . . . . . . . . . . . . . . . . E-40
To change the illumination duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-49
To enter the World Time Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-41
To view the time in another time zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-41 Adjusting Hand Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-50
To specify standard time or daylight saving time (DST) for a city . . . . . . . . . . . E-42
Button Operation Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-53
To swap your Home City and World Time City . . . . . . . . . . . . . . . . . . . . . . . . E-43
To turn the button operation tone on and off . . . . . . . . . . . . . . . . . . . . . . . . . E-53
Using the Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-44
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-55
To enter the Alarm Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-44
To set an alarm time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-45 Main Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-56
To test the alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-46
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-59
To turn an alarm and the Hourly Time Signal on and off . . . . . . . . . . . . . . . . . E-47
To stop the alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-47 Operating Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-62

User Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-73

E-6 E-7

Mode Reference Guide To do this: Enter this mode: See:

The mode you should select depends on what you want to do. x View the current time in one of 48 cities
(31 time zones) around the globe World Time Mode E-40
To do this: Enter this mode: See: x Swap Home Time and World Time
x View the current date in the Home City Set an alarm time Alarm Mode E-44
x Configure Home City and daylight saving time (DST)
settings
x Configure time and date settings Timekeeping Mode E-17
x One-press stopwatch timing start
x Change the display illumination duration setting
x Enable/disable the button operation tone
x Use the stopwatch to measure elapsed time
Stopwatch Mode E-25
x Use Target Time Alarm
Use the countdown timer Countdown Timer Mode E-36

E-8 E-9
 Operation Guide 5478
Selecting a Mode x Press C to cycle between the modes as shown below.
x In the Timekeeping Mode, press E to enter the Stopwatch Mode. x To return to the Timekeeping Mode from any other mode, hold down C for about
x For more information about using the Stopwatch Mode, see “To enter the two seconds.
Stopwatch Mode” (page E-26). x In any mode (except a setting mode), press B to illuminate the display.

Timekeeping Mode Stopwatch Mode

E-10 E-11

x The dial hand indicates the mode (Timekeeping Mode: ).

When you enter the Timer Mode (TR) or Stopwatch Mode (ST), the dial hand first
indicates TR or ST, and then moves to the position shown below.

Timekeeping Mode Countdown Timer Mode World Time Mode Alarm Mode Stopwatch Mode

C C C C

E-12 E-13

General Functions (All Modes) 1. While holding down B, press C.

The functions and operations described in this section can be used in all modes. x This will cause the hour and minute hands to move to a location where they do
not block your view of the digital display.
Moving the Hands Out of the Way for Better Viewing Example: When the current time is 8:23
You can use the procedure below to temporarily move the hour and minute hands
out of the way to better view what is on the display. Flashes while the hands are moved out of the way.
x This operation can be performed in any mode. In the case of a setting mode
(setting flashing on the screen), the hands will move out of the way automatically,
even if you do not perform the below operation.

E-14 E-15

2. Holding down B again as you press C will cause the hands to return to their Timekeeping
normal positions (normal timekeeping).
Use the Timekeeping Mode to set and view the current time and date.
Note
x Watch button functions are the same regardless of whether the hands are moved Day of week Month-Day PM indicator
out of the way or at their normal positions.
x Changing to another mode will cause the hands to move back to their normal
positions.
x The hands also will move back to their normal positions automatically if no Hour D
operation is performed for about one hour.
Second
Auto Return
x If you do not perform any operation for about two or three minutes while
configuring settings (setting flashing on the digital display) in any mode, the watch
will exit the setting operation and return to normal display. Minute Second

Dial hand Hour : Minute

E-16 E-17

Configuring Home City Settings 3. After the setting is the way you want, press A to return to the Timekeeping
Mode.
There are two Home City settings: actually selecting the Home City, and selecting
either standard time or daylight saving time (DST). Note
x You can check the city code and name (English) of your Home City by pressing A.
To configure Home City settings x After you specify a city code, the watch will use UTC* offsets in the World Time
City Code 1. In the Timekeeping Mode, hold down A until the Mode to calculate the current time for other time zones based on the current time
flashing SET Hold indicator disappears from the in your Home City.
display and the currently selected city code flashes on * Coordinated Universal Time, the world-wide scientific standard of timekeeping.
the display. The reference point for UTC is Greenwich, England.
x This indicates the Home City setting mode.
2. Use D (+) and B (–) to scroll through city codes until
the one you want is displayed.
x For details about city codes, see the “City Code
Table” at the back of this manual.
x Holding down either button scrolls at high speed.

E-18 E-19
 Operation Guide 5478
To change the Daylight Saving Time (summer time) setting Adjusting the Digital Time and Date Settings
1. In the Timekeeping Mode, hold down A until the
DST indicator Use the procedure below to adjust the digital time and date settings.
flashing SET Hold indicator disappears from the
display and the currently selected city code flashes on
the display. To configure the digital time and date settings
1. In the Timekeeping Mode, hold down A until the
2. Press C to display the DST setting mode. flashing SET Hold indicator disappears from the
3. Press D to toggle between Daylight Saving Time (ON) display and the currently selected city code flashes on
and Standard Time (OFF). the display.
x Note that you cannot switch between daylight saving
time and standard time while UTC is selected as your
Home City.
4. After the setting is the way you want, press A to
return to the Timekeeping Mode.
x The DST indicator appears to indicate that Daylight
Saving Time is turned on.

E-20 E-21

2. Press C to move the flashing in the sequence shown below to select the other 3. When the timekeeping setting you want to change is flashing, perform the
settings. operation described below.
C C C Screen To do this: Do this:
Home City DST
(page E-18) (page E-20) 12/24-Hour Format Seconds Toggle between 12-hour (12H) and 24-hour
(24H) timekeeping Press D.
C
Reset the seconds to 00 Press D.
C Hour

C Change the hour or minute

Use D (+) and B (–) to
Illumination Duration change these settings.
Minute Change the year
(page E-48) x Holding down either button
C C scrolls at high speed.
Change the month or day
Button Operation Tone On/Off
(page E-53) Day Month Year
C C C 4. Press A to exit the setting mode.

E-22 E-23

Note Using the Stopwatch

x Resetting the seconds to 00 while the current count is in the range of 30 to
59 causes the minutes to be increased by 1. The stopwatch measures elapsed time, split times, and two finishes.
x The watch’s built-in full automatic calendar makes allowances for different month x The measurement range of the stopwatch is 23 hours, 59 minutes, 59.99 seconds.
lengths and leap years. Once you set the date, there should be no reason to When the measurement range is exceeded, measurement stops (display becomes
change it except after you have the watch’s battery replaced. 0).
x The day of the week changes automatically when the date changes. Minutes

Hours 1/100 Second

Minutes Seconds

Seconds

E-24 E-25

To enter the Stopwatch Mode 2. Now you can perform the same operations as those shown on page E-28.
You can enter the Stopwatch Mode using any one of the methods below.
Entering from Another Mode (including the Timekeeping Mode)
Entering Directly from the Timekeeping Mode Press C as many times as necessary to navigate to the Stopwatch Mode as shown
If the stopwatch was reset to all zeros the last time you used it, a new elapsed time on page E-13.
operation will start as soon as you enter the Stopwatch Mode. x To enter from the Timekeeping Mode using this method, press C four times.
See page E-28 for information about measuring an elapsed time. x This will display the stopwatch screen in the same status as it was the last time you
1. In the Timekeeping Mode, press E. exited the Stopwatch Mode. However, if you exited with a split time displayed, the
This will result in one of the following, depending on the status of the stopwatch the split time operation will be released when you return.
last time you exited the Stopwatch Mode.
x If reset (stopped at 0:00 00"00): Timing starts.
One-press timing start from the Timekeeping Mode (direct timing start from the
Timekeeping Mode)
x If an ongoing timing operation is paused: Timing remains paused.
x If an ongoing timing operation is in progress*: Timing continues to be performed.
* An ongoing stopwatch timing operation continues even if you navigate to
another mode from the Stopwatch Mode.

E-26 B B E-27

To perform an elapsed time operation Note

E E E E D x Once started, elapsed time measurement continues until the elapsed time
measurement limit is reached, even if you change to a different mode.
Start Stop (Resume) (Stop) Reset
Using the Target Time Alarm
To pause at a split time
You can set a target time in the range of one minute to 24 hours, in units of one
E D D E D minute.
Start Split Split release Stop Reset A beeper will sound for 10 seconds when the elapsed timing of the stopwatch
(SPL displayed) reaches the target time.

To measure two finishes

E D E D D
Start Split Stop Split release Reset
(SPL displayed) Second runner Display time of
First runner finishes. finishes. second runner.
Display time of first
runner.

E-28 E-29
 Operation Guide 5478
To set a target time 7. Press D to toggle the target time alarm between on and off.
1. Reset the stopwatch to all zeros. x TARGET is displayed while the target time alarm is on, and not displayed while
Hours
it is off.
2. Hold down A until the flashing SET Hold indicator
disappears from the display and the hour digit starts to 8. After all the settings are the way you want, press A to exit the setting screen.
flash. Release A after the hour digit starts to flash.
To use the target time alarm
3. Use D (+) and B (–) to change the hour setting.
1. Reset the stopwatch to all zeros and then press E.
x Holding down either button scrolls at high speed. This will cause TARGET to flash on the display.
x For a target time of 24 hours, set 00 hours
00 minutes. 2. Now you can perform the same operations as those in the steps on page E-28.
4. Press C to switch to the minutes setting. Start Target time
Target Time operation in 5. Use D (+) and B (–) to change the minutes setting.
progress x Holding down either button scrolls at high speed.
(1) (2) (4)
6. Press C to display the target time alarm on/off setting. (3)

E-30 E-31

x You can get an idea of time elapsed until the target time from changes in the (2) From target time half until target time is reached
display. x Screen: As shown in the figure, all of the part that
(1) From start up to half of target time indicates minutes flashes.
x Screen: As shown in the figure, rightmost indicator that x TARGET flashes at high speed starting from one
indicates minutes flashes. minute before the target time.
x TARGET starts to flash.

E-32 E-33

(3) Target time reached Note

x Beep for 10 seconds. x TARGET flashes in the above operation even if the watch is in another mode.
x Screen: Changes as shown in the figure.
To stop the alert beeper
x TARGET becomes unlit.
Pressing any button while the alert beeper is sounding will stop it.
x Pressing D or E operates the elapsed time operation on page E-28.

To perform stopwatch timing without using the Target Time Alarm

Use step 7 under “To set a target time” to disable the target time alarm.

(4) After target time is expired

x Screen: Rightmost indicator that indicates minutes flashes (at slow speed).
x Elapsed time is measured, with TARGET remaining unlit.
x Resetting the elapsed stopwatch time automatically causes TARGET to re-
appear. You can re-use the same target time, if you want.

E-34 E-35

Countdown Timer To configure the countdown timer

x If a countdown timer operation is in progress, press E
1/10 second The countdown timer can be set within a range of to pause it and then press D to reset the target time to
one minute to 60 minutes. An alarm sounds when the its start time.
Seconds
countdown reaches zero. x If a countdown timer operation is paused, press D to
To enter the Countdown Timer Mode reset the timer to its start time.
Use C to select the Countdown Timer Mode as shown 1. Hold down A until the flashing SET Hold indicator
on page E-12. disappears from the display and the minutes digits
start to flash. Release A after the digits start to flash.
2. Use D (+) and B (–) to change the minutes setting.
x Holding down either button scrolls at high speed.
3. After all the settings are the way you want, press A to
exit the setting screen.
Minutes
Seconds

E-36 E-37

To perform a countdown timer operation To stop the alarm

Press any button.
E E E E D
Start Stop (Resume) (Stop) Reset

Countdown in Progress

Dial hand: Moves from right to left.

E-38 E-39
 Operation Guide 5478
Checking the Current Time in a Different Time Zone To enter the World Time Mode
Use C to select the World Time Mode as shown on page E-13.
World Time City hour and You can use the World Time Mode to view the current
minute time in one of 31 time zones (48 cities) around the To view the time in another time zone
globe. The city that is currently selected in the World In the World Time Mode, press D to change the city code setting.
Time Mode is called the “World Time City”. x Holding down D scrolls at high speed.
x The hour and minute hands indicate information for x To display the UTC city code (differential 0), press B and D at the same time.
the currently selected Home City.
x When you enter the World Time Mode, the currently
selected city code and city name (English) scroll once
across the digital display. After that, the city code
remains displayed.
x You can view the name (English) of your Home City
Second by pressing A.

Indicates WT.

City code of World Time City

E-40 E-41

To specify standard time or daylight saving time (DST) for a city To swap your Home City and World Time City
DST indicator 1. In the World Time Mode, press D to display the city In the World Time Mode, hold down E for at least three seconds.
code (time zone) whose Standard Time/Daylight Saving This will cause SWAP Hold to flash on the display, and then your Home City and
Time setting you want to change. World Time City will be swapped.
2. Hold down A for about two seconds. Example: To swap the Home City (TYO) and World Time City (NYC)
x This toggles the city code you selected in step 1
between Daylight Saving Time (DST indicator World Time City (NYC) time New World Time City (TYO)
displayed) and standard time (DST indicator not
displayed).
x Note that you cannot switch between standard time/
E, at least
daylight saving time (DST) while UTC is selected as 3 seconds
the World Time City.
x The standard time/daylight saving time (DST) setting
affects only the currently displayed city. Other cities
are not affected.

TYO (Tokyo) time NYC (New York) time

E-42 E-43

Using the Alarm x If you do not perform any operation for about two or three minutes in the Alarm
Mode, the watch will automatically return to the Timekeeping Mode.
Alarm time (Hour : Minute) You can set five independent daily alarms. When a daily
alarm is turned on, an alarm tone will sound for about To set an alarm time
Alarm number 10 seconds each day when the time in the Timekeeping
Alarm indicator 1. In the Alarm Mode, use D to display the alarm whose
Mode reaches the preset alarm time. One of the alarms settings you want to change.
is a snooze alarm that repeats every five minutes, up to
seven times. AL1 AL2 AL3
You can also turn on an Hourly Time Signal, which will
cause the watch to beep twice every hour on the hour.
SIG SNZ AL4
To enter the Alarm Mode
Use C to select the Alarm Mode as shown on page E-13. 2. Hold down A until the flashing SET Hold indicator
x The snooze alarm screen is indicated by SNZ, while the disappears from the display and the alarm time hour
other alarm screens are numbered AL1 through AL4. digits start to flash. Release A after the digits start
The Hourly Time Signal screen is indicated by SIG. to flash.
Alarm ON/OFF indicator x When you enter the Alarm Mode, the data you were x ALM appears on the display, indicating that alarm
viewing when you last exited the mode appears first. setting is enabled.
E-44 E-45

3. Press C to move the flashing between the hour and the minute digits. To turn an alarm and the Hourly Time Signal on and off
x The selected digits are those that are flashing. Alarm on indicator In the Alarm Mode, press D to select an alarm or the
Hourly Time Signal.
4. Use D (+) and B (–) to change the hour and minute settings. Hourly time signal x When the alarm you want or the Hourly Time Signal
x Holding down either button scrolls at high speed. on indicator
is displayed, press E to toggle it between on
x When setting the alarm time using the 12-hour format, take care to set the time (ON displayed) and off (OFF displayed).
correctly as a.m. (no indicator) or p.m. (PM indicator).
x The alarm on indicator (when any alarm is on), snooze
5. Press A to exit the setting mode. alarm indicator (when the snooze alarm is on), and the
Hourly Time Signal on indicator (when the Hourly Time
To test the alarm Signal is on) are shown on the display in all modes.
In the Alarm Mode, hold down D to sound the alarm. x SNZ and ALM will be displayed while the snooze
alarm is turned on.

To stop the alarm

Snooze alarm on indicator
Press any button.

E-46 E-47

Illumination To change the illumination duration

1. In the Timekeeping Mode, hold down A until the flashing SET Hold indicator
The display of the watch is illuminated for easy reading in the dark. disappears from the display and the currently selected city code flashes on the
display.
To turn on illumination
Press B in any mode to illuminate the display. 2. Press C ten times to display the illumination duration setting screen.
x You can use the procedure below to select either 1.5 seconds or three seconds as x The current illumination duration setting (1 or 3) will be flashing in the display.
the illumination duration. x See the sequence in step 2 of the procedure under “To configure the digital time
and date settings” (page E-21) for information about how to scroll through setting
screens.
3. Press D to toggle the illumination duration between three seconds (3 displayed)
and 1.5 seconds (1 displayed).
4. After all the settings are the way you want, press A to exit the setting screen.

E-48 E-49
 Operation Guide 5478
Adjusting Hand Positions 1. In the Timekeeping Mode, hold down A for about
five seconds until 00 starts to flash. Release A after
The watch hands can go out of alignment with the time on the digital display if it 00 flashes.
is exposed to strong magnetism or impact. If this happens, you should adjust the x This indicates the dial hand adjustment mode.
hand positions.
2. If the dial hand is not at 0 o’clock, use D (+) and B
Important! (–) to move it there.
x You do not need to perform the operation below as long as the analog hands
indicate the same time as the digital display.

Dial hand

E-50 E-51

Hour hand and minute hand 3. Press C. Button Operation Tone

x This enters the hour and minute hand adjustment
mode. You can turn the button operation tone on or off as
x Press C again* to enter the dial hand adjustment desired.
mode. x Even if you turn off the button operation tone, the Target
* Nothing will happen if you press C while the hands Time Alarm, alarms, the Hourly Time Signal, and other
are moving. beepers all operate normally.

4. If the hour and minute hands are not at 12 o’clock, To turn the button operation tone on and off
use D (+) and B (–) to adjust them until they are. 1. In the Timekeeping Mode, hold down A until the
x Holding down either button scrolls at high speed. flashing SET Hold indicator disappears from the
display and the currently selected city code flashes on
5. Press A to return to the Timekeeping Mode.
the left side of the upper display.
Check to make sure that the time indicated by the
hands matches the time on the digital display. If the 2. Press C nine times to display the button operation
times don’t match, perform the correction procedure tone On/Off screen (page E-22).
above again. The screen will show either KEY or MUTE.

E-52 B E-53

3. Press D to toggle the setting between KEY (ON) and MUTE (OFF). Troubleshooting
4. After all the settings are the way you want, press A to exit the setting screen.
Time Setting
■ The current time setting is off by hours.
Your Home City setting may be wrong (page E-18). Check your Home City setting and
correct it, if necessary.
■ The current time setting is off by one hour.
You may need to change your Home City’s standard time/daylight saving time
(DST) setting. Use the procedure under “Adjusting the Digital Time and Date
Settings” (page E-21) to change the standard time/daylight saving time (DST) setting.

World Time Mode

■ The time for my World Time City is off in the World Time Mode.
This could be due to incorrect switching between standard time and daylight saving
time. See “To specify standard time or daylight saving time (DST) for a city” (page E-42)
for more information.

E-54 E-55

Main Indicators Graphic

The graphic flashes in each mode as described below.
1 2 34 5 6 Number Name See
Mode Flashing
1 Snooze alarm on indicator E-47
Timekeeping Seconds of current time
2 Alarm on indicator E-45
Stopwatch Minutes of elapsed time measurement
3 Hourly time signal on indicator E-47
Countdown Timer Minutes of countdown
4 PM indicator E-17 World Time Seconds of current time
5 Hands shifted indicator E-14 Synced with World Time seconds.
6 DST indicator E-20, E-42
Target Time operation in
7 progress E-30

E-56 E-57

Dial Hand Specifications

The dial hand indicates the information below in each mode.
Mode Dial Hand Indication Accuracy at normal temperature: ±15 seconds a month
Timekeeping Mode name Digital Timekeeping: Hour, minutes, seconds, p.m. (PM), month, day, day of the
week
Stopwatch Elapsed seconds Time format: 12-hour and 24-hour
Countdown Timer Seconds count Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099
World Time Mode name Other: Home City code (can be assigned one of 48 city codes);
Standard Time/Daylight Saving Time (summer time)
Alarm Mode name
Analog Timekeeping: Hour, minutes (hand moves every 20 seconds)
Stopwatch:
Measuring unit: 1/100 second
Measuring capacity: 23:59' 59.99"
Measuring modes: Elapsed time, split time, two finishes, Direct timing start from
the Timekeeping Mode, Target Time Alarm

E-58 B E-59
 Operation Guide 5478
Countdown Timer: Power Supply: One lithium battery (Type: CR2016)
Measuring unit: 1/10 second Approximate battery operating time: 3 years under the following conditions:
Countdown range: 60 minutes x Stopwatch: 40 hours/month
Countdown start time setting range: 1 to 60 minutes (1-minute increments) x Alarm: 10 seconds/day
x 1 illumination operation (1.5 seconds) per day
World Time: 48 cities (31 time zones)
Other: Daylight Saving Time/Standard Time; Home City/World Time City Frequent use of illumination runs down the battery.
switching
Alarms: 5 Daily alarms (with 1 snooze alarm); Hourly time signal Specifications are subject to change without notice.
Illumination: LED (light-emitting diode); Selectable illumination duration
(approximately 1.5 seconds or 3 seconds)
Other: Button operation tone on/off; Moving the Hands to View the Digital Display

E-60 E-61

City Code Table

L-1

City Code Table City City UTC Offset/ City City UTC Offset/
Code GMT Differential Code GMT Differential
City UTC Offset/ City UTC Offset/ MOW Moscow SEL Seoul
City City +3 +9
Code GMT Differential Code GMT Differential JED Jeddah TYO Tokyo
PPG Pago Pago –11 Fernando de THR Tehran +3.5 ADL Adelaide +9.5
FEN –2
HNL Honolulu –10 Noronha DXB Dubai +4 GUM Guam
ANC Anchorage –9 RAI Praia –1 +10
KBL Kabul +4.5 SYD Sydney
YVR Vancouver UTC KHI Karachi +5 NOU Noumea +11
–8
LAX Los Angeles LIS Lisbon 0 DEL Delhi +5.5 WLG Wellington +12
YEA Edmonton LON London KTM Kathmandu +5.75
DEN Denver
–7
MAD Madrid xThis table shows the city codes of this
DAC Dhaka +6
MEX Mexico City PAR Paris RGN Yangon +6.5
watch (As of January 2016).
CHI Chicago
–6
ROM Rome +1 xThe rules governing global times
BKK Bangkok +7
NYC New York –5 BER Berlin (GMT differential and UTC offset) and
SIN Singapore summer time are determined by each
YHZ Halifax –4 STO Stockholm HKG Hong Kong
+8 individual country.
YYT St. John’s –3.5 ATH Athens BJS Beijing
BUE Buenos Aires CAI Cairo +2 TPE Taipei
–3
RIO Rio De Janeiro JRS Jerusalem
L-2 L-3