Permeability Test in The Field by Pumping From Wells

Permeability Test in the Field by Pumping Figure shows a case where the
from Wells top permeable layer, whose

In the field, the average hydraulic conductivity of a hydraulic conductivity has to be
soil deposit in the direction of flow can be determined, is unconfined and
determined by performing pumping tests from underlain by an impermeable
wells layer. During the test, water is
pumped out at a constant rate
from a test well that has a
perforated casing. Several
observation wells at various
radial distances are made around
the test well. Continuous
observations of the water level
in the test well and in the
observation wells are made after
the start of pumping, until a
steady state is reached. The
steady state is established when
the water level in the test and
observation wells becomes
constant.
A sandy layer 10 m thick overlies an impervious layer. The water table is in the sandy
layer at a depth of 1.5 m below the ground surface. Water is pumped out from a well
at the rate of 100 liters per second and the drawdown of the water table at radial
distances of 3 m and 25 m is 3 and 0,5 m, respectively. Determine the coefficient of
permeability.
r1  25 m
r2  3 m
1.5 m
10 m
h2 h1
h1  10  1.5  0.5  8 m
h2  10  1.5  3.0  5.5 m
 25 
2.303  100  10 3  log10  
k  3   0.002 m sec
 82  5.52
 
The average hydraulic conductivity for a confined aquifer can be determined by
conducting a pumping test from a well with a perforated casing that penetrates the
full depth of the aquifer and by observing the piezometric level in a number of
observation wells at various radial distances. Pumping is continued at a uniform rate q
until a steady state is reached.
A permeability pumping test was carried out from a well sunk into a confined stratum
of dense sand. Figure shows the arrangement of the pumping well and observations
wells, together with relevant dimensions. Initially, the piezometric surface was located
at a depth of 2.5 m. When the steady state was achieved at a pumping rate of 37.4
m3/hr the following drawdowns were observed:
Pumping well: dw = 4.46 m

Observation well 1: d1=0.42 m
Observation well 2: d2=1.15 m
Determine the coefficient of permeability.

h1  7.4  2.5  0.42  4.48 m, r1  50 m
h2  7.4  2.5  1.15  3.75 m, r2  15 m
m3 1 hr m3
q  37.4   0.0104
hr 3600 s s
 50 
0.0104  log  
k  15   2.33  104 m s
2.727  11.7  4.48  3.75
 
Seepage
In many instances,the flow of water through soil is not in one direction only,
nor is it uniform over the entire area perpendicular to the flow. In such cases,
the groundwater flow is generally calculated by the use of graphs referred to
as flow nets. The concept of the flow net is based on Laplace’s equation of
continuity, which governs the steady flow condition for a given point
in the soil mass.
The continuity equation in an isotropic medium represents two orthogonal

families of curves—that is, the flow lines and the equipotential lines. A flow
line is a line along which a water particle will travel from upstream to the
downstream side in the permeable soil medium. An equipotential line is a line
along which the potential head at all points is equal. Thus, if piezometers are
placed at different points along an equipotential line, the water level will rise
to the same elevation in all of them.
A combination of a number of
flow lines and equipotential
lines is called a flow net.
To complete the graphic construction of a flow net, one must draw the flow
and equipotential lines in such a way that
1. The equipotential lines intersect the flow lines at right angles.
2. The flow elements formed are approximate squares.
Drawing a flow net takes several trials. While constructing the flow net, keep the
boundary conditions in mind. For the flow net shown , the following four
boundary conditions apply:
Condition 1: The upstream and downstream surfaces of the permeable layer (lines
ab and de) are equipotential lines.
Condition 2: Because ab and de are equipotential lines, all the flow lines intersect
them at right angles.
Condition 3: The boundary of the impervious layer—that is, line fg—is a flow line,
and so is the surface of the impervious sheet pile, line acd.
Condition 4: The equipotential lines intersect acd and fg at right angles.

Permeability Test in The Field by Pumping From Wells

Uploaded by

Copyright:

Available Formats

Permeability Test in The Field by Pumping From Wells

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Permeability Test in The Field by Pumping From Wells

Uploaded by

Copyright:

Available Formats

Permeability Test in the Field by Pumping Figure shows a case where the

from Wells top permeable layer, whose

Pumping well: dw = 4.46 m

Determine the coefficient of permeability.

The continuity equation in an isotropic medium represents two orthogonal

You might also like