MDKBK BL BM BN BP BR Bs BT Bu BV Service Manual

Service Manual
Marine Generator Set
MDKBK (Spec A-G)

MDKBL (Spec A-G)
MDKBM (Spec A-G)
MDKBN (Spec A-G)
MDKBP (Spec A-E)
MDKBR (Spec A-E)
MDKBS (Spec A-B)
MDKBT (Spec A-C)
MDKBU (Spec A-C)
MDKBV (Spec A-B)
English
Original Instructions 9-2016 981-0543 (Issue 15)
Table of Contents
1. SAFETY PRECAUTIONS .............................................................................................................. 1
1.1 Overview ................................................................................................................................. 1
1.2 Precaution Symbols ................................................................................................................ 1
1.3 General Safety Precautions.................................................................................................... 2
1.4 Electrical Shocks and Arc Flashes Can Cause Severe Personal Injury or Death.................. 4
1.5 Generator Voltage Is Deadly .................................................................................................. 5
1.6 Engine Exhaust Is Deadly....................................................................................................... 5
1.7 Diesel Fuel is Combustible ..................................................................................................... 6
1.8 Battery Gas is Explosive......................................................................................................... 6
1.9 Moving Parts Can Cause Severe Personal Injury Or Death .................................................. 6
1.10 Flammable Vapor Can Cause a Diesel Engine to Overspeed ............................................. 6
1.11 Hazards of Carbon Monoxide ............................................................................................... 6
1.11.1 Carbon Monoxide Poisoning...................................................................................... 7
1.11.2 Special Risks of CO on Boats.................................................................................... 7
1.11.3 Protection From CO Poisoning .................................................................................. 8
1.12 Substances Hazardous to Health ......................................................................................... 8
1.12.1 Antifreeze (Fleetguard - ES Compleat and EG Premix) ............................................ 8
1.12.2 Gas Oil ..................................................................................................................... 10
1.12.3 Lubricant Oil - Premium Blue E 15W40 ................................................................... 11
1.13 Generator Set Warning Labels ........................................................................................... 12
2. INTRODUCTION.......................................................................................................................... 15
2.1 About This Manual................................................................................................................ 15
2.1.1 Warning - Generator Set Not Ignition Protected ........................................................ 15
2.2 Related Literature ................................................................................................................. 16
2.3 Model Identification ............................................................................................................... 16
2.3.1 Nameplate Location ................................................................................................... 17
2.4 Emissions Label.................................................................................................................... 17
2.4.1 Typical Emissions Label Location.............................................................................. 17
2.5 Noise..................................................................................................................................... 18
2.6 Electromagnetic Compatibility Compliance........................................................................... 18
2.7 Build Standards..................................................................................................................... 18
3. MAINTENANCE ........................................................................................................................... 21
3.1 Periodic Maintenance ........................................................................................................... 21
3.1.1 Periodic Maintenance Schedule ................................................................................ 21
3.2 General Inspection................................................................................................................ 22
3.2.1 Service Point Locations ............................................................................................. 23
3.2.2 Battery Connections................................................................................................... 24
3.2.3 Oil Level .................................................................................................................... 24
3.2.4 Fuel System Leaks .................................................................................................... 25
3.2.5 Coolant Level ............................................................................................................. 26
981-0543 (Issue 15) i Copyright © 2016 Cummins Inc.

Table of Contents 9-2016
3.2.6 Raw Water System .................................................................................................... 26

3.2.7 Exhaust System ......................................................................................................... 26
3.2.8 Mechanical System .................................................................................................... 27
3.3 Maintaining the Battery ......................................................................................................... 27
3.4 Maintaining the Lubrication System...................................................................................... 27
3.4.1 Oil Recommendations................................................................................................ 27
3.4.2 Changing Engine Oil and Filter.................................................................................. 28
3.5 Maintaining the Fuel System ................................................................................................ 29
3.5.1 Fuel Recommendations ............................................................................................. 29
3.5.2 Draining the Fuel Filter............................................................................................... 30
3.5.3 Replacing Fuel Filter .................................................................................................. 30
3.5.4 Priming the Fuel System............................................................................................ 31
3.6 Maintaining the Cooling System ........................................................................................... 32
3.6.1 Cooling System ......................................................................................................... 33
3.6.2 Cooling System .......................................................................................................... 34
3.6.3 Cooling System .......................................................................................................... 35
3.6.4 Pressure Cap ............................................................................................................. 35
3.6.5 Coolant Hoses............................................................................................................ 36
3.6.6 Siphon Break.............................................................................................................. 36
3.6.7 Coolant Recommendations........................................................................................ 37
3.6.8 Replenishing Normal Coolant Loss............................................................................ 38
3.6.9 Refilling Cooling System ............................................................................................ 38
3.6.10 Draining and Cleaning Cooling System ................................................................... 38
3.6.11 Heat Exchanger ....................................................................................................... 39
3.6.12 Zinc Anode............................................................................................................... 41
3.6.13 Replacing the Thermostat........................................................................................ 41
3.6.14 Replacing Raw Water Pump Impeller...................................................................... 42
3.6.15 Adjusting V-Belt Tension.......................................................................................... 44
3.6.16 Replacing V-Belt When PTO Equipped ................................................................... 45
3.7 Storing the Generator Set..................................................................................................... 45
3.8 Cold Temperature Storage ................................................................................................... 46
3.9 Returning the Generator Set to Service ............................................................................... 46
4. GENERATOR SET CONTROL.................................................................................................... 47

4.1 Overview ............................................................................................................................... 47
4.2 Controller .............................................................................................................................. 47
4.2.1 Major Functions of Generator Set Controller ............................................................. 47
4.2.2 Control Block Diagram ............................................................................................... 49
4.2.3 Connectors................................................................................................................. 50
4.2.4 Removal/Replacement............................................................................................... 50
4.2.5 Configuring Generator Set Controller Using Digital Display ...................................... 52
4.2.6 Configuring Generator Set Controller Using Control Switch...................................... 53
4.3 Control Switch Schematic ..................................................................................................... 53
4.4 Control Relays ...................................................................................................................... 54
4.5 Master Hour Meter (M11) ..................................................................................................... 54
4.5.1 Master Hour Meter (M11)........................................................................................... 54
Copyright © 2016 Cummins Inc. ii 981-0543 (Issue 15)

9-2016 Table of Contents
4.6 Emergency Stop Switch/Circuit Breaker............................................................................... 55

4.7 DC Circuit Breaker ................................................................................................................ 55
4.8 Engine Oil Pressure Sensor (E1).......................................................................................... 55
4.8.1 Oil Pressure Sensor (E1) ........................................................................................... 55
4.9 Coolant Temperature Sender (E2) ....................................................................................... 56
4.9.1 Coolant Temperature Sender (E2)............................................................................. 57
4.10 High Exhaust Temperature Switch (S5) ............................................................................. 58
4.10.1 High Exhaust Temperature Switch (S5) .................................................................. 58
4.11 Raw Water Flow Switch (S6) .............................................................................................. 59
4.11.1 Raw Water Flow Switch (S6) ................................................................................... 60
4.12 Low Coolant Level Switch (S3)........................................................................................... 61
4.12.1 Low Coolant Level Switch (S3)................................................................................ 62
4.13 Glow Plug Relay (K3) ......................................................................................................... 63
4.14 Starter Relay (K4) ............................................................................................................... 63
4.15 Governor Actuator (A12)..................................................................................................... 63
4.15.1 Governor Actuator.................................................................................................... 64
4.15.2 Governor Actuator.................................................................................................... 65
4.16 Network Interface Module (NIM)......................................................................................... 65
4.16.1 NIM Mounting Location ............................................................................................ 66
4.16.2 NIM Configuration Jumpers ..................................................................................... 66
4.16.3 Troubleshooting LEDs.............................................................................................. 67
4.16.4 Troubleshooting Network ......................................................................................... 67
4.17 Electrostatic Discharge Control Bonding ............................................................................ 67
5. ENGINE AND ACCESSORIES.................................................................................................... 69

5.1 Major Engine Service............................................................................................................ 69
5.2 Exhaust Manifold .................................................................................................................. 69
5.3 Fuel System .......................................................................................................................... 71
5.3.1 Fuel System ............................................................................................................... 72
5.3.2 Fuel Filter ................................................................................................................... 72
5.3.3 Fuel Pump Test.......................................................................................................... 72
5.3.4 Fuel Pump Removal and Installation ......................................................................... 73
5.3.5 Fuel Fittings................................................................................................................ 73
5.3.6 Fuel Hose................................................................................................................... 73
5.3.7 Glow Plugs ................................................................................................................. 73
5.4 Starter ................................................................................................................................... 74
981-0543 (Issue 15) iii Copyright © 2016 Cummins Inc.

5.4.1 Negative Ground Connection..................................................................................... 74

5.4.2 Ground Isolation Relay (K9)....................................................................................... 74
5.4.3 Starter Motor Mounting .............................................................................................. 75
5.5 Raw Water Pump.................................................................................................................. 75
5.6 Battery Charging Alternator .................................................................................................. 75
6. ALTERNATOR ............................................................................................................................. 77
6.1 Overview ............................................................................................................................... 77
6.1.1 Generator Stator and Winding Resistances .............................................................. 79
6.2 Winding Insulation Resistance Test Procedure .................................................................... 79
6.3 Winding Resistance Test Procedure .................................................................................... 79
6.4 Break-Out Tool 300-5512 ..................................................................................................... 80
6.5 Exciter Stator ........................................................................................................................ 80
6.5.1 Winding Insulation Resistance................................................................................... 80
6.5.2 Winding Resistance ................................................................................................... 80
6.5.3 Exciter Stator and End Bell ........................................................................................ 81
6.6 Exciter Rotor ......................................................................................................................... 81
6.7 Rotating Rectifiers................................................................................................................. 82
6.8 Main Rotor ............................................................................................................................ 83
6.8.3 Rotor Assembly.......................................................................................................... 85
6.9 Main Stator............................................................................................................................ 85
6.9.1 Winding Insulation Resistance .................................................................................. 85
6.9.3 Quadrature Winding Insulation Resistance................................................................ 86
6.9.4 Quadrature Winding Resistance ................................................................................ 86
6.9.5 Winding to Winding Insulation Resistance................................................................. 86
6.10 Generator Disassembly ...................................................................................................... 87
6.11 Generator Reassembly ....................................................................................................... 88
6.12 Reconnecting the Generator............................................................................................... 89
6.13 Line Circuit Breakers........................................................................................................... 89
7. CHANGING GENERATOR SET FREQUENCY .......................................................................... 91

7.1 As Manufactured................................................................................................................... 91
7.2 Reconnection Label .............................................................................................................. 91
7.3 Changing Frequency............................................................................................................. 92
7.4 Reconnecting Generator....................................................................................................... 93
8. ADJUSTING AC OUTPUT VOLTAGE ......................................................................................... 95

8.1 Adjusting Voltage .................................................................................................................. 95
8.2 Adjusting Voltage Using Digital Display................................................................................ 95
8.3 Adjusting Voltage Using Control Switch ............................................................................... 96
9. TROUBLESHOOTING ................................................................................................................. 97
Copyright © 2016 Cummins Inc. iv 981-0543 (Issue 15)

9-2016 Table of Contents
9.1 Overview ............................................................................................................................... 97

9.2 Troubleshooting with Digital Display..................................................................................... 97
9.3 Troubleshooting with Status Lamp ....................................................................................... 97
9.4 Troubleshooting Generator Set Faults.................................................................................. 98
9.4.1 No Code - No Response at Digital Display or Control Switch ................................... 98
9.4.2 No Code - Starter Engages and Disengages ............................................................ 99
9.4.3 No Code - Starting Batteries do not Maintain a Charge ............................................ 99
9.4.4 No Code - No AC Power When Generator Set is Running ....................................... 99
9.4.5 Code No. 1 - High Engine Temperature .................................................................. 100
9.4.6 Code No. 2 - Low Oil Pressure ............................................................................... 100
9.4.7 Code No. 3 - Service Check .................................................................................... 100
9.4.8 Code No. 4 - Overcrank........................................................................................... 101
9.4.9 Code No. 5 - Warning Shutdown due to CO ........................................................... 102
9.4.10 Code No. 7 - Loss of Raw Water Flow .................................................................. 102
9.4.11 Code No. 12 - High AC Voltage............................................................................. 102
9.4.12 Code No. 13 - Low AC Voltage.............................................................................. 103
9.4.13 Code No. 14 - High AC Frequency ........................................................................ 103
9.4.14 Code No. 15 - Low AC Frequency......................................................................... 104
9.4.15 Code No. 22 - Governor Overload......................................................................... 104
9.4.16 Code No. 23 - Faulty Oil Pressure Sender ............................................................ 105
9.4.17 Code No. 24 - Faulty Temperature Sender ........................................................... 105
9.4.18 Code No. 27 - Loss of AC Voltage Sense ............................................................. 105
9.4.19 Code No. 29 - High Battery Voltage ...................................................................... 106
9.4.20 Code No. 32 - Starting Fault .................................................................................. 106
9.4.21 Code No. 35 - Control Card Failure - EE............................................................... 106
9.4.22 Code No. 36 - Unknown Shutdown ....................................................................... 106
9.4.23 Code No. 37 - Invalid Generator Set Configuration............................................... 107
9.4.24 Code No. 38 - Field Overload ................................................................................ 107
9.4.25 Code No. 41 - Generator Rotor Fault .................................................................... 108
9.4.26 Code No. 43 - Control Card Failure - RAM............................................................ 108
9.4.27 Code No. 45 - Speed Sense Lost .......................................................................... 108
9.4.28 Code No. 57 - Overprime....................................................................................... 108
9.4.29 Code No. 58 - High Exhaust Temperature ............................................................ 108
9.4.30 Code No. 59 - Low Coolant Level.......................................................................... 109
9.4.31 Code No. 61 - External Shutdown ......................................................................... 109
10. SPECIFICATIONS .................................................................................................................... 111

10.1 MDKBK, MDKBL, and MDKBM Specifications Table ....................................................... 111
10.2 MDKBN, MDKBP, and MDKBR Specifications Table....................................................... 114
10.3 MDKBT, MDKBU, and MDKBV Specifications Table ....................................................... 117
11. MAINTENANCE RECORD ....................................................................................................... 121
APPENDIX A. WIRING DIAGRAMS ............................................................................................... 123

A.1 Wiring Drawing ................................................................................................................... 125
APPENDIX B. OUTLINE DRAWINGS ............................................................................................ 129
981-0543 (Issue 15) v Copyright © 2016 Cummins Inc.

B.1 MDKBK Outline Drawing .................................................................................................... 131

B.2 MDKBL Outline Drawing..................................................................................................... 133
B.3 MDKBM and MDKBN Outline Drawing .............................................................................. 135
B.4 MDKBP, MDKBR, and MDKBV Outline Drawing ............................................................... 137
B.5 MDKBT and MDKBU Outline Drawing ............................................................................... 140
APPENDIX C. WIRING HARNESSES............................................................................................ 143

C.1 MDK Wiring Harness.......................................................................................................... 145
Copyright © 2016 Cummins Inc. vi 981-0543 (Issue 15)

1 Safety Precautions
1.1 Overview
Thoroughly read the Operator Manual before operating the generator set. It contains important instructions
that should be followed during operation and maintenance. Safe operation and top performance can only
be achieved when equipment is properly operated and maintained. The owners and operators of the
generator set are solely responsible for its safe operation.
Generator set operation, maintenance, and installation must comply with all applicable local, state, and
federal codes and regulations. Electricity, fuel, exhaust, moving parts, and batteries present hazards which
can result in severe personal injury or death. Only trained and experienced personnel with knowledge of
fuels, electricity, and machinery hazards shall perform generator set installation or adjustment procedures.
Also, only trained and experienced personnel with knowledge of fuels, electricity, and machinery hazards
shall remove, dismantle, or dispose of the generator set.
SAVE THESE INSTRUCTIONS.
WARNING
This generator set is not a life support system. It can stop without warning. Children, persons
with physical or mental limitations, and pets could suffer personal injury or death. A personal
attendant, redundant power, or alarm system must be used if generator set operation is critical.
WARNING
This generator set is not be the main source of power for communication and steering systems.
It can stop without warning.
1.2 Precaution Symbols

The following symbols used in this manual alert you to potential hazards to operator, maintenance
personnel, and equipment.
DANGER
Indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING
Indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION
Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
NOTICE
Indicates information considered important, but not hazard-related (e.g., messages relating to
property damage).
981-0543 (Issue 15) 1 Copyright © 2016 Cummins Inc.

1. Safety Precautions 9-2016
1.3 General Safety Precautions

WARNING
Hot, moving, and electrically live parts can cause severe personal injury or death. Keep children
away from the generator set.
WARNING
Hot, moving, and electrically live parts can cause severe personal injury or death. Only trained
and experienced personnel should make adjustments while the generator set is running.
WARNING
Electrical Generating Equipment
Incorrect operation can cause severe personal injury or death.
Do not operate equipment when fatigued, or after consuming any alcohol or drug.
WARNING
Incorrect operation and maintenance can result in severe personal injury or death
Make sure that only suitably trained and experienced service personnel perform electrical and/or
mechanical service.
WARNING
Moving Parts
Moving parts can cause severe personal injury.
Use extreme caution around moving parts. All guards must be properly fastened to prevent
unintended contact.
WARNING
Running the generator set without the cover or service door can cause severe personal injury or
equipment damage. Do not operate the generator set with the cover or service doors removed.
WARNING
Hot Pressurized Liquid
Contact with hot liquid can cause severe burns.
Do not open the pressure cap while the engine is running. Let the engine cool down before
removing the cap. Turn the cap slowly and do not open it fully until the pressure has been
relieved.
WARNING
Hot Surfaces
Contact with hot surfaces can cause severe burns.
Wear appropriate PPE when working on hot equipment and avoid contact with hot surfaces.
Copyright © 2016 Cummins Inc. 2 981-0543 (Issue 15)

9-2016 1. Safety Precautions
WARNING
Combustible Liquid
Ignition of combustible liquids is a fire or explosion hazard which can cause severe burns or
death.
Do not store fuel, cleaners, oil, etc., near the generator set.
WARNING
Combustible Liquid
Ignition of combustible liquids is a fire or explosion hazard which can cause severe burns or
death.
Do not use combustible liquids like ether.
WARNING
Toxic Hazard
Ethylene glycol, used as an engine coolant, is toxic to humans and animals.
Wear appropriate PPE. Clean up coolant spills and dispose of used coolant in accordance with
local environmental regulations.
WARNING
Toxic Hazard
Used engine oils have been identified by some state and federal agencies to cause cancer or
reproductive toxicity.
Do not ingest, breathe the fumes, or contact used oil when checking or changing engine oil.
Wear protective gloves and face guard.
WARNING
Inhalation of carbon monoxide can cause severe personal injury or death. Test and confirm that
all carbon monoxide detectors are working in accordance with the manufacturer's instructions or
owner's manual prior to every startup, and after 8 hours of running.
WARNING
Toxic Gases
Substances in exhaust gases have been identified by some state and federal agencies to cause
cancer or reproductive toxicity.
Do not breathe in or come into contact with exhaust gases.
DANGER
Accidental or remote starting.
Accidental starting of the generator set while working on it can cause severe personal injury or
death
To prevent accidental or remote starting while working on the generator set, disconnect the
negative (–) battery cable at the battery using an insulated wrench.

CAUTION
Unsecured or loose fasteners can cause equipment damage. Make sure all fasteners are secure
and properly torqued.
CAUTION
Oily rags and other material can cause fire and restrict cooling. Keep the generator set, drip pan,
and compartment clean.
WARNING
Fire Hazard
Accumulated grease and oil are a fire hazard. Fire can cause severe burns or death.
Keep the generator set and the surrounding area clean and free from obstructions. Repair oil
leaks promptly.
NOTICE
Keep multi-class ABC fire extinguishers handy. Class A fires involve ordinary combustible
materials such as wood and cloth. Class B fires involve combustible and flammable liquid fuels
and gaseous fuels. Class C fires involve live electrical equipment. (Refer to NFPA No. 10 in
applicable region.)
1.4 Electrical Shocks and Arc Flashes Can Cause

Severe Personal Injury or Death
WARNING
Electric Shock Hazard
Voltages and currents present an electrical shock hazard that can cause severe burns or death.
Contact with exposed energized circuits with potentials of 50 Volts AC or 75 Volts DC or higher
can cause electrical shock and electrical arc flash. Refer to standard NFPA 70E or equivalent
safety standards in corresponding regions for details of the dangers involved and for the safety
requirements.
Guidelines to follow when working on de-energized electrical systems:

• Use proper PPE. Do not wear jewelry and make sure that any conductive items are removed from
pockets as these items can fall into equipment and the resulting short circuit can cause shock or
burning. Refer to standard NFPA 70E for PPE standards.
• De-energize and lockout/tagout electrical systems prior to working on them. Lockout/Tagout is
intended to prevent injury due to unexpected start-up of equipment or the release of stored energy.
Please refer to the lockout/tagout section for more information.
• De-energize and lockout/tagout all circuits and devices before removing any protective shields or
making any measurements on electrical equipment.
• Follow all applicable regional electrical and safety codes.
Guidelines to follow when working on energized electrical systems:

NOTICE
It is the policy of Cummins Inc. to perform all electrical work in a de-energized state. However,
employees or suppliers may be permitted to occasionally perform work on energized electrical
equipment only when qualified and authorized to do so and when troubleshooting, or if de-
energizing the equipment would create a greater risk or make the task impossible and all other
alternatives have been exhausted.
NOTICE
Exposed energized electrical work is only allowed as per the relevant procedures and must be
undertaken by a Cummins authorized person with any appropriate energized work permit for the
work to be performed while using proper PPE, tools and equipment.
In summary:
• Do not tamper with or bypass interlocks unless you are authorized to do so.
• Understand and assess the risks - use proper PPE. Do not wear jewelry and make sure that any
conductive items are removed from pockets as these items can fall into equipment and the resulting
short circuit can cause shock or burning. Refer to standard NFPA 70E for PPE standards.
• Make sure that an accompanying person who can undertake a rescue is nearby.
1.5 Generator Voltage Is Deadly

• Generator electrical output connections must be made by a trained and experienced electrician in
accordance with applicable codes.
• Use caution when working on live electrical equipment. Remove all jewelry, make sure clothing and
shoes are dry, stand on a dry wooden platform or rubber insulating mat, and use tools with insulated
handles.
1.6 Engine Exhaust Is Deadly

• Properly working carbon monoxide detectors must be located in all living areas of the boat.
• Never occupy the boat while the generator set is running unless the boat is equipped with properly
working marine carbon monoxide detectors.
• The exhaust system must be installed in accordance with the generator set Installation Manual and
be free of leaks.
• Prior to every startup and after every eight hours of running, all carbon monoxide detectors must be
tested and confirmed to be working in accordance with the manufacturer instructions or owner
manual.
• Make sure the bilge is adequately ventilated with a power exhauster or blower.
• Inspect for exhaust leaks at every startup and after every eight hours of operation.
• For more information about carbon monoxide see American Boat and Yacht Council (ABYC)
publication TH-22—Educational Information About Carbon Monoxide.

1.7 Diesel Fuel is Combustible

• Do not smoke or turn electrical switches on or off where fuel fumes are present or in areas sharing
ventilation with fuel tanks or equipment. Keep flames, sparks, pilot lights, arc-producing equipment,
and all other sources of ignition well away.
• Fuel lines must be secured, free of leaks, and separated or shielded from electrical wiring.
1.8 Battery Gas is Explosive

• Wear splash-proof safety glasses.
• Do not smoke or permit flames or sparks to occur near the battery at any time or anywhere near the
generator set.
• To reduce arcing when disconnecting or reconnecting battery cables, always disconnect the
negative (–) battery cable first and reconnect it last.
1.9 Moving Parts Can Cause Severe Personal Injury Or

Death
• Do not wear loose clothing or jewelry near moving parts such as PTO (power take-off) shafts, fans,
belts, and pulleys.
• Keep hands away from moving parts.
• Keep protective guards in place over fans, belts, pulleys, and other moving parts.
1.10 Flammable Vapor Can Cause a Diesel Engine to

Overspeed
WARNING
Flammable vapor can cause an engine to overspeed and become difficult to stop, resulting in
possible fire, explosion, severe personal injury, and death. Do not operate a diesel- or gasoline-
powered generator set where a flammable vapor environment can be created by fuel spill, leak,
etc.
The owners and operators of the generator set are solely responsible for operating the generator set
safely.
1.11 Hazards of Carbon Monoxide

WARNING
Engine-driven generators can produce harmful levels of carbon monoxide causing nausea,
fainting, or death. It is possible to be harmed by this poisonous gas despite good generator set
maintenance and proper ventilation.

1.11.1 Carbon Monoxide Poisoning

Carbon Monoxide (CO) is an odorless, colorless, tasteless, and non-irritating gas. You cannot see it or
smell it. Exposure, even to low levels of CO, for a prolonged period can lead to asphyxiation (lack of
oxygen) resulting in death.
Mild effects of CO poisoning include:
• eye irritation
• dizziness
• sleepiness
• headaches
• fatigue
• inability to think clearly
More extreme symptoms include:
• vomiting
• seizures
• collapse
1.11.2 Special Risks of CO on Boats

Depending on air temperature and wind, CO can accumulate between hulls, under an overhanging deck
or rear swimming platform, and in and around the boat. A swimmer can be exposed to lethal levels of CO
when the generator set is running. Passengers on deck and in the living quarters can also be exposed,
especially when the boat is docked, beached, or tied to a neighboring boat.
The risk of exposure to CO can be multiplied greatly by the "station wagon" effect, obstructions that block
exhaust dissipation, and infiltration from neighboring boats. To protect against all three situations, it is
recommended that reliable and approved marine CO detector alarms be installed on your boat.
• The Station Wagon Effect: A boat pushes aside the air through which it is moving, causing a zone
of low pressure in the back of the boat and cabins into which exhaust gases can be drawn (see
figure below). A breeze across an anchored boat can have the same effect. Opening doors and
windows so that air can flow through the boat can reduce the effect.

FIGURE 1. STATION WAGON EFFECT

• Obstructions: Anchoring near a large object such as a boat house or sea wall, or in a confined
space such as a canyon, can cause exhaust gases to accumulate in and around the boat despite
good generator set maintenance and proper ventilation. Don't run the generator set when anchored
in such places.
• Exhaust from Neighboring Boats: When boats are anchored in close quarters, exhaust from
neighboring boats can accumulate in and around yours.
1.11.3 Protection From CO Poisoning

• Constantly watch for swimmers when the generator set is running.
• Make sure exhaust cannot get under the deck, between hulls, or enter the living quarters through a
window, vent, or door.
• Make sure all CO detectors are working properly.
• Pay attention to the signs of CO poisoning.
• Check the exhaust system for corrosion, obstruction, and leaks each time you start the generator set
and every eight hours if you run it continuously.
1.12 Substances Hazardous to Health

Generator sets use substances, and emit and create wastes, that can cause health risks. Generator set
operators must use appropriate personal protective equipment (such as clothing, gloves, protective
glasses, goggles, and respiration equipment) when lungs, eyes, or skin are exposed to fuel, oil, coolant,
wet batteries, grease, cleaning agents, or other substances. Use appropriate containers for transport,
storage, and disposal of waste substances. Follow local regulations for disposal and recycling.
1.12.1 Antifreeze (Fleetguard - ES Compleat and EG Premix)

This antifreeze is also known as an ethylene glycol based coolant, summer coolant, coolant additive. It is
a purple-colored viscous liquid with a mild chemical odor, is soluble in water, and is harmful under certain
conditions. It contains ethylene glycol and diethylene glycol. Ethylene glycol is a potentially hazardous
constituent.
The substance has a boiling point of 107° C (224.6° F) and a flash point of 121° C (249.8° F).
It is used as an engine coolant additive and can be found in engine cooling systems and heat exchangers.
Installers, operators, and maintainers are likely to encounter this substance.

1.12.1.1 Hazardous Reactions

Ethylene glycol is combustible when exposed to heat or flame and can react vigorously with oxidants.
• It is a moderate explosive hazard in the form of vapor when exposed to heat or flame. Hazardous
products resulting from combustion or decomposition include carbon monoxide, carbon dioxide, and
acrid smoke. Self-contained breathing apparatus must be worn in the event of fume build up.
• It is incompatible with sulfuric acid, nitric acid, caustics, and aliphatic amines. Avoid any strong
oxidizing agents.
• It may cause neurological signs and symptoms, kidney damage, and is a skin and eye irritant.
• It is very toxic in particulate form upon inhalation.
• It is harmful if swallowed. A lethal dose for humans is reported to be 100 ml.
1.12.1.2 Protective Measures

Refrain from eating, drinking, or smoking when using the product. Adopt a high standard of personal
hygiene. In case of skin contact, wash immediately with soap and water.
Ensure good ventilation and avoid heat sources. Avoid breathing mist. If there is a risk of vapor or
particulate, use a suitable organic vapor mask.
Eye protection, gloves, overalls, and an impervious apron should be worn. Avoid contamination inside the
gloves. If overalls become contaminated, discontinue use and clean thoroughly.
1.12.1.3 Storage and Transport

Store and transport only in correctly marked containers. Keep containers closed when not in use. Keep
cool, out of sunlight, and away from naked flames and strong acids. Do not freeze. Store well away from
food-stuffs and drinking water. Take special care to avoid discharge into drains, sewers, and water-course.
Contain leaks and spills with sand, earth, or non-combustible absorbent material to prevent entry of
substance into drains (sewage systems), water-courses, and land. Eliminate all ignition sources. Use a
plastic shovel to transfer to a suitable container. Dispose of unwanted or absorbed substance through an
authorized contractor to a licensed site.
1.12.1.4 Emergency Action

• Fire - Fire fighters are to use self contained breathing apparatus. Keep fire-exposed containers cool.
Prevent run-off from entering waterways, drains, and drinking water supplies. Extinguishing media:
CO2, alcohol resistant foam, dry powder, or water spray.
• Ingestion - Toxic by ingestion. If swallowed, contact a doctor or poison control center. Induce
vomiting only under the advice of a doctor or poison control center. Delayed treatment may result in
fatality.
• Inhalation (of vapor) - Remove from further exposure. In case of irritation to lungs or throat, seek
medical advice.
• Aspiration (inhalation of liquid) - Obtain immediate medical assistance.
• Eyes - Flush copiously with water or preferably eye-wash solution for at least five minutes. Seek
medical advice.
• Skin - Wash thoroughly with soap and water and seek medical attention if irritation develops.
Change clothing if necessary and wash clothing before re-use.
• Spillage - Soak up using an absorbent material and dispose of as directed under Storage and
Transport.

1.12.2 Gas Oil

This product is also known as red diesel, fuel oil, and type A1 or A2. It can be pale red or clear liquid with
a characteristic mild odor. It contains catalytically cracked oil, petroleum distillates, quinizarin, and gas oil
maker dye red. The catalytically cracked oil and petroleum distillates are potentially hazardous
constituents.
The substance has an initial boiling point of 180° C (345° F), a flash point greater than 56° C (132.8° F), a
vapor pressure less than 0.7 mm Hg at 20° C (68° F), and has negligible solubility in water.
It is used as a fuel for off-road diesel powered vehicles and stationary engines and can be found in fuel
tanks, pipes, and injection systems. The substance should not be used for any other purpose without
contacting the manufacturer or supplier. Installers, operators, and maintainers are likely to encounter this
substance.

This liquid is flammable. Avoid smoking, heat sources - such as welding and naked flames - sparks, and
static electricity build-up. Thermal decomposition products are hazardous, containing COX, NOX, and SOX
compounds.
The vapor is explosive. High vapor concentrations can cause respiratory irritation, dizziness, nausea, and
loss of consciousness. Excessive and prolonged exposure to the mist can cause chronic inflammatory
reaction of the lungs and a form of pulmonary fibrosis.
Avoid strong oxidizing agents such as chlorates which may be used in agriculture.
Gas oil is slightly irritating to the skin and has a de-fatting action. Toxicity following single exposure to a
high level of gas oil is of low importance. Prolonged, repeated skin contact may de-fat the skin resulting in
possible skin irritation and dermatitis. In some cases warty, cancerous growths have occurred.

Ensure good ventilation and avoid heat sources. Observance of good housekeeping rules will ensure
general safety. Do not smoke. Avoid breathing mist.
When working on or testing injection equipment, special care is required to avoid perforation of skin by
high pressure fuel. Use eye protection in the event of suspected high pressure leak.
Adopt a high standard of personal hygiene. In the case of skin contact, wash well with soap and water.
Use gloves, overalls, and eye protection if there is a risk of splashing. Use oil-impervious gloves and avoid
contamination inside the gloves. If overalls become contaminated, discontinue use and clean thoroughly.
Contaminated clothing should be removed, soaked with water, and laundered before re-use.
No special respiratory precautions are necessary in normal use.
Do not use as a solvent for removing dirt and grease, etc, from skin.

Store and transport only in correctly marked containers. Keep containers closed when not in use. Keep
cool, out of sunlight, and away from naked flames. Electrical continuity is required between the transport
and storage vessels during product transfer.
Contain leak or spill with sand, earth, or other suitable material, and prevent entry of substance into
drainage (sewage system), water-courses, and land. Dispose of unwanted or absorbed substance through
an authorized contractor to a licensed site.
Inform fire and local authorities should the product reach waterways, drains, etc.


• Fire - Avoid making sparks. Fire fighters are to use self-contained breathing apparatus. Keep fire-
exposed containers cool, using water fog or spray. Prevent run-off from entering waterways, drains,
and drinking water supplies.
◦ Extinguishing media for large fire: Foam or water fog. Never use water jet.
◦ Extinguishing media for small fire: Foam or dry powder, AAAF, CO2, sand, earth.
• Ingestion - Do not induce vomiting. Wash mouth out with water and send to hospital immediately.
• Inhalation (of vapor) - Remove from further exposure. Obtain medical assistance immediately.
• Aspiration (inhalation of liquid) - If, following ingestion of gas oil, vomiting occurs, there is danger of
aspiration into the lungs. This would cause intense local irritation and chemical pneumonitis that can
be fatal. Obtain immediate medical assistance.
• Eyes - Irrigate copiously with water or preferably eye-wash solution for at least five minutes. If
irritation persists seek medical advice.
• Skin - Wash thoroughly with soap and water. Change clothing if necessary. If high pressure injection
has occurred prompt surgical attention is required.
• Spillage - Absorb using sand, earth, or other suitable material. Dispose of unwanted or absorbed
flammable material as directed under Storage and Transport.
1.12.3 Lubricant Oil - Premium Blue E 15W40

Also known as oil, lube oil, sump oil. New oil is a dark, viscous liquid with a slight characteristic odor. The
base oil contains distillates (petroleum) and solvent-dewaxed heavy paraffinic. It is not classified as
dangerous according to Directive 1999/45/EC and its amendments, and is not classified according to the
EU regulations.
It has a boiling point greater than 150° C (302° F), and a flash point Open Cup of 220° C (438° F)
(Cleveland) and is insoluble in cold water.
It is used in engine lubricant oil systems, sump pan and filters, make-up tanks, and piping systems as a
lubrication oil for use in a wide range of diesel engines operating under severe conditions. Installers,
operators, and maintainers are likely to encounter this product.

This product is stable, although slightly re-active, with oxidizing agents. Results of decomposition are
carbon oxides (CO, CO2) and water.
Although harmful if ingested (swallowed) or aspirated (breathed in), repeated or prolonged exposure is not
known to aggravate medical conditions.
Used oil may contain harmful combustion by-products and un-burnt fuel that will cause skin reactions as
detailed for fuel. Particular care must be taken if oil from a severely overheated engine is handled. Use
impervious gloves, lab coat, and safety glasses. Do not breathe vapor or spray.

Ensure good ventilation and avoid heat sources.
Adopt a high standard of personal hygiene. In case of skin contact, wash thoroughly with soap and water.
Use safety glasses, impervious gloves, and lab coat. Avoid contamination inside the gloves. If overalls
become contaminated, discontinue use and clean thoroughly.
No special respiratory precautions are necessary in normal use. Do not breathe vapor or spray when
handling hot materials.


Store and transport only in correctly marked containers. Keep containers tightly sealed when not in use.
Keep in cool, well ventilated area, out of sunlight and away from naked flames. Store well away from food-
stuffs and drinking water.
Wear splash goggles, full suit, boots, and gloves. Absorb leaks or spills with an inert material and dispose
of unwanted or absorbed substance through an authorized contractor to a licensed site. Finish cleaning by
spreading water on the contaminated surface and allow to evacuate through the sanitary system.

• Fire - Fire-fighters are to use self contained breathing apparatus and full turnout gear. Keep fire-
exposed containers cool.
◦ Extinguishing media for large fire: Use water spray, fog or foam. Do not use water jet.
◦ Extinguishing media for small fire: Use dry chemical powder or CO2.
• Ingestion - Do not induce vomiting. Obtain medical advice immediately.
• Inhalation (of vapor) - Remove from further exposure. Obtain medical attention.
• Aspiration (inhalation of liquid) - Obtain immediate medical assistance.
• Eyes - Flush copiously with water or preferably eye-wash solution for at least fifteen minutes. Obtain
medical advice.
• Skin - Wash thoroughly with soap and water. Obtain medical advice if irritation develops. Change
clothing if necessary and wash before re-use.
• Spillage - Absorb with an inert material and dispose of as directed under Storage and Transport.
1.13 Generator Set Warning Labels

Warning signs are provided on the generator set at or near the point of risk. To avoid injury, always take
the necessary precautions as indicated on the sample signs shown below.
Caution or Warning.
Indicates a risk of personal injury.
Caution or Warning of Temperature Hazard.

Indicates a risk of personal injury from high temperature.
Caution or Warning of High Voltage Hazard.

Indicates a risk of personal injury from electric
shock or electrocution.
Caution or Warning of Engine Coolant Pressure Hazard.

Indicates a risk of personal injury from hot pressurized engine coolant.

Caution or Warning.
Indicates to read Operator Manual for additional information.
Caution or Warning of No Step.

Indicates a risk of personal injury or equipment damage from stepping on
equipment.
Caution or Warning of Combustion or Explosion Hazard.

Indicates a risk of personal injury from explosion.
Caution or Warning of Belt and Rotating Part Hazard.

Indicates a risk of personal injury from entanglement in moving parts.
Caution or Warning of Chemical (ingestion or burn) Hazard.

Indicates a risk of personal injury or asphyxiation from poisonous fumes
or toxic gases.
Caution or Warning of High Voltage or Current Source Hazard.

Indicates a risk of personal injury from electrical shock or electrocution.
Caution or Warning of Fan and Rotating Part Hazard.

Indicates a risk of personal injury from entanglement in moving parts.

This page is intentionally blank.

2 Introduction
WARNING
Hazardous Voltage
Contact with high voltages can cause severe electrical shock, burns, or death.
Make sure that only a trained and experienced electrician makes generator set electrical output
connections, in accordance with the installation instructions and all applicable codes.
WARNING
Faulty electrical generating equipment can cause severe personal injury or death.
Generator sets must be installed, certified, and operated by trained and experienced person in
accordance with the installation instructions and all applicable codes.
2.1 About This Manual

This is the Service Manual for the generator set or sets listed on the front cover.
The information contained within the manual is based on information available at the time of going to print.
In line with Cummins Power Generation policy of continuous development and improvement, information
may change at any time without notice. The users should therefore make sure that before commencing
any work, they have the latest information available. The latest version of this manual is available on
QuickServe Online (https://quickserve.cummins.com).
This manual includes generator set specifications, troubleshooting resolutions for all fault codes,
maintenance schedule, service and maintenance procedures for the generator set control, engine,
accessories, and generator as well as adjusting the AC output voltage and changing the generator set
frequency .
See the Parts Manual for part identification numbers and required quantities. Genuine Cummins Onan
replacement parts are recommended for best results.
2.1.1 Warning - Generator Set Not Ignition Protected

WARNING
The generator set or sets included in this manual are not ignition protected and shall not be used
in a flammable vapor environment.
WARNING
Within the Parts Manual, MC parts are marine critical and must comply with boating safety
ignition protection, backfire, fire resistance, exhaust system integrity, or other requirements
established by regulatory agencies, such as the U.S. Coast Guard, ABYC, and ISO. When marine
critical parts are replaced for any reason, use Cummins Onan parts that are identified with the
part numbers in the appropriate Parts Manual.

2. Introduction 9-2016
2.2 Related Literature

Before any attempt is made to operate the generator set, the operator should take time to read all of the
manuals supplied with the generator set, and to familiarize themselves with the warnings and operating
procedures.
CAUTION
A generator set must be operated and maintained properly if you are to expect safe and reliable
operation. The Operator manual includes a maintenance schedule and a troubleshooting guide.
The Health and Safety manual must be read in conjunction with this manual for the safe
operation of the generator set:
• Health and Safety Manual (0908-0110)

The relevant manuals appropriate to your generator set are also available, the documents below are in
English:
• Operator Manual (0981-0181)
• Installation Manual (0981-0648)
• Service Manual for (0981-0543)
• Parts Manual MDKBK (0981-0279); MDKBL, MDKBM, MDKBN (0981-0280); MDKBP, MDKBR,
MDKBU (0981-0288); MDKBT and MDKBV (0981-0284)
• Service Manual for Kubota 03-M-E3B and E3BG and 03-M DI-E3B (0981-0551)
• Specification and Data Sheet (MDKBK A1477, MDKBL A1476, MDKBM A1478, MDKBN A1479,
MDKBP A1480, MDKBR A1481, MDKBT A1494, MDKBU A1488, MDKBV A1537) (For engineering
data specific to the generator set)
• Standard Repair Times - BT Family (0900-0625)
• Warranty Manual (F1117-0002)
• Global Commercial Warranty Statement (A028U870)
2.3 Model Identification

The generator set model name is found on the nameplate, which is mounted on the service side of the
generator set. See figure below. Every character is significant (the last character of the model number is
the specification letter, which is important for obtaining the right parts).
WARNING
Improper service or replacement of parts can lead to severe personal injury or death and damage
to equipment and property. Service personnel must be qualified to perform electrical and
mechanical service.

9-2016 2. Introduction
2.3.1 Nameplate Location
FIGURE 2. NAMEPLATE LOCATION
2.4 Emissions Label

The emissions label states compliance with applicable engine emissions regulations for US EPA certified
models (17 MDKDP, 21.5 MDKDR, and 29 MDKDS). Refer also to the Federal Emissions Design And
Defect Limited Warranty For C.I. Engine (Diesels) publication that was shipped in the same package as
the Operator Manual.
NOTICE
The emissions warranty statement is for EPA certified only products.
2.4.1 Typical Emissions Label Location
FIGURE 3. TYPICAL EMISSIONS LABEL LOCATIONS

2.5 Noise
Generator sets emit noise. As noise level and time of exposure increase, risk of hearing damage
increases. Chapter 10 on page 111 includes specific noise level information for these generator sets. Use
personal hearing protection appropriate for your exposure to generator set noise.
When used in countries where compliance to the EU Noise directive is required: This generator set has
not been evaluated and is not marked for use in open air. Install the generator set in accordance with the
Installation Manual. Obey local noise restrictions when you operate the generator set.
2.6 Electromagnetic Compatibility Compliance

Generator sets emit and receive electromagnetic (radio frequency) energy. If the generator set affects
operation of nearby devices, or nearby devices affect generator set operation, increase the distance
between them.
When used in countries where compliance to the EMC directive is required: This generator set has been
evaluated for use in the residential, commercial, and light industrial environments.
2.7 Build Standards

The generator set and its control system have been designed, constructed and tested generally in
accordance with the following Standards where applicable.
Standard Title
BS EN 1037:1995+a1:2008 Safety of machinery - Prevention of unexpected start up.
BS EN ISO 14121-1:2007 Safety of machinery. Risk assessment principles.
BS EN ISO 13857:2008 Safety of machinery. Safety distances to prevent hazard zones being
reached by upper and lower limbs.
BS EN 349:1993+A1:2008 Safety of machinery - Minimum gaps to avoid crushing parts on the human
body.
BS EN 547-1:1996+A1:2008 Safety of machinery - Human body dimensions - Part 1: Principles for
determining the dimensions required for openings for whole body access
into machinery.
BS EN 547-2:1996+A1:2008 Safety of machinery - Human body dimensions - Part 2: Principles for
determining the dimensions required for access openings.
BS EN 547-3:1996+A1:2008 Safety of machinery - Human body dimensions - Part 3: Anthropomorphic
data.
BS EN 60204-1:2006+A1:2009 Safety of machinery. Electrical equipment of machines. General
requirements.
BS EN 614-1:2006+A1:2009 Safety of machinery. Ergonomic design principles. Terminology and
general principles.
BS EN 953:1997+A1:2009 Safety of machinery - Guards - General requirements for the design and
construction of fixed and movable guards.
BS EN ISO 12100-1:2003+A1:2009 Safety of machinery. Basic concepts, general principles for design. Basic
terminology, methodology

9-2016 2. Introduction
Standard Title
BS EN ISO 12100-2:2003+A1:2009 Safety of machinery. Basic concepts, general principles for design.
Technical principles
BS EN ISO 13732-1:2008 Ergonomics of the thermal environment. Methods for the assessment of
human responses to contact with surfaces. Hot surfaces
BS EN ISO 13849-1:2008 Safety of machinery - Safety-related parts of control systems
BS EN ISO 13850:2006 Safety of machinery - Emergency stop. Principles for design.
BS EN 61310-1:2008 Safety of machinery - Indication, marking and actuation - Part 1:
Requirements for visual, auditory and tactile signals.
BS EN 61310-2:2008 Safety of machinery - Indication, marking and actuation - Part 2:
Requirements for marking.
BS EN 61000-6-1:2007 Electromagnetic compatibility (EMC). Generic standards. Immunity
standard for residential, commercial and light-industrial environments.
BS EN 61000-6-3:2007 Electromagnetic compatibility (EMC). Generic standards. Emission
standard for residential, commercial and light-industrial environments.
BS EN 1299:1997+A1:2008 Mechanical vibration and shock - Vibration isolation of machines -
Information for the application of source isolation
BS EN 1679-1:1998 Reciprocating internal combustion engines - Safety - Part 1: Compression
ignition engines
BS EN 12601:2001 Reciprocating internal combustion engine driven generating sets - Safety


3 Maintenance
3.1 Periodic Maintenance
Periodic maintenance is essential for top performance and long generator set life. Use the Periodic
Maintenance Schedule below as a guide for normal periodic maintenance.
Maintenance, replacement, or repair of emission control devices and systems may be performed by any
engine repair establishment or individual. However, warranty work must be completed by an authorized
Cummins Onan service representative.
To help keep generator set maintenance regular and provide a basis for warranty claims, record
maintenance performed, see Chapter 11 on page 121.
3.1.1 Periodic Maintenance Schedule

TABLE 1. PERIODIC MAINTENANCE SCHEDULE
MAINTENANCE FREQUENCY
Every
After Every Every Every Every
MAINTENANCE OPERATION Every Every Every 5
First Mont Year/ Year/ Year/
Day/8 800 2 Years
50 h/100 200 350 500
Hrs hrs Years /2000
Hrs Hrs Hrs Hrs Hrs
Hrs
General Inspection1 x
Check Engine Oil Level x
Drain Water From Fuel Filter x
Check Battery and Battery Connections2 x
Check V-Belt Tension3 x
Check Siphon Break x
Change Oil and Filter - All except MDKDS,
x x
MDKDT, and MDKDU5
Change Oil and Filter - Only
x x
MDKDS, MDKDT, and MDKDU5
Change Fuel Filter x
Inspect Zinc Anode x
Replace Raw Water Pump Impeller x
Adjust Valve Lash4
x
Replace Coolant, Pressure Cap, and Thermostat x
Inspect Generator Bearing4 x

3. Maintenance 9-2016
1 - Includes inspection of Oil Level, Coolant Level, Fuel System, Exhaust System, Batteries and Battery Connections.
2 - See battery manufacturer's recommendations.
3 - Check for slippage, cracking, and wear.
4 - Must be performed by a qualified mechanic (authorized Cummins Onan Dealer).
5 - Perform twice as often when using high sulfur fuel. See Engine Oil Recommendations in the Maintenance chapter.
3.2 General Inspection

Inspect the following before the first start of the day and after every eight hours of operation.
• Battery Connections
• Oil Level
• Fuel System
• Coolant Level
• Raw Water System
• Exhaust System
• Mechanical System
Review the following figure for assistance in locating various service points.

9-2016 3. Maintenance
3.2.1 Service Point Locations
No. Description No. Description

1 Oil Dipstick 4 Fuel Filter and Water Separator
2 Oil Fill 5 Oil Drain Hose
3 Oil Filter
FIGURE 4. OIL AND FUEL SERVICE POINTS - MDKDP, MDKDR, MDKDV


1 Fuel Filter 4 Oil Drain Hose
2 Oil Dipstick 5 Oil Filter
3 Oil Fill
FIGURE 5. OIL AND FUEL SERVICE POINTS - MDKDS, MDKDT, AND MDKDU
3.2.2 Battery Connections

WARNING
Flames, sparks, or arcing at battery terminals, light switches, or other equipment can ignite
battery gas, causing severe personal injury. Ventilate the battery area before working on or near
a battery, wear safety glasses, and do not smoke. Turn work light on or off away from the battery.
When performing maintenance procedures or when servicing a battery, stop the generator set
and disconnect the charger before disconnecting battery cables. Using an insulated wrench,
disconnect the negative (–) cable first and reconnect it last.
Check the battery terminals for clean, tight connections. Loose or corroded connections have high
electrical resistance which makes starting harder.
3.2.3 Oil Level

WARNING
Engine components (drains, filters, hoses, etc.) can be hot and cause severe burns, lacerations
of the skin, and liquid splash. Use personal protective equipment when working with or around
hazardous materials. Examples of personal protective equipment include (but are not limited to)
safety glasses, protective gloves, hard hats, steel toed boots, and protective clothing.

WARNING
Crankcase pressure can blow hot engine oil out the fill opening causing, severe burns. Always
stop the generator set before removing the oil fill cap.
WARNING
State and federal agencies have determined that contact with used engine oil can cause cancer
or reproductive toxicity. Avoid skin contact and breathing of vapors. Use rubber gloves and
wash exposed skin.
CAUTION
Too little oil can cause severe engine damage. Too much oil can cause high oil consumption.
Keep the oil level between the high and low beads (or markings) on the dipstick.
1. Shut off the generator set.

2. Pull the oil fill plug and dipstick out of the oil fill neck. The plug may be difficult to pull straight out - tilt
the plug in its socket while pulling out.
3. Wipe off the dipstick and thread it back into the fill neck. Seat the plug, which snaps into its socket.
4. Remove the plug and dipstick again and check the oil level on the dipstick. Replace and seat the oil
fill plug.
5. Add or drain oil as necessary if the oil level is not within the bead markings (FULL or ADD markings).
See Section 3.4 on page 27 for oil recommendations.
NOTICE
It is not necessary to add oil between oil changes unless the oil level has dropped more
than 1/3 of the way between the high and low beads. A full quart (0.9 liter) can be added if
the oil level is at the lower bead.
FIGURE 6. OIL LEVEL DIPSTICK ADD/FULL MARKINGS
3.2.4 Fuel System Leaks

WARNING
Fuel leaks can lead to fire. Repair leaks immediately. Do not run the generator set if it causes fuel
to leak.

WARNING
1. Check for leaks at hose, tube, and pipe fittings in the fuel supply and return systems while the
generator set is running and while it is stopped.
2. Check flexible fuel hoses for cuts, cracks, abrasions, and loose hose clamps.
3. Make sure fuel lines do not rub against other parts.
4. Replace worn or damaged fuel line parts before leaks occur. Replace hose with a high pressure fuel
injection system USCG TYPE A1 or ISO 7840-A1 fuel hose.
5. Prime the fuel system if the generator set ran out of fuel.
3.2.5 Coolant Level

The recovery tank is designed to maintain coolant level, not to fill the system. Keep the level of coolant in
the recovery tank between COLD and HOT. See Section 3.6.7 on page 37 for coolant specifications.
Also see Section 3.6.9 on page 38 for detailed instructions on refilling the cooling system.
1. Check coolant level in the recovery tank and, if necessary, refill the recovery tank to COLD when the
engine is cold or to HOT when it is at normal running temperature. Use the recommended antifreeze
mixture.
2. If the tank is empty, check for and repair any coolant leaks and refill the system through the fill neck
on the engine. Use the recommended antifreeze mixture.
3.2.6 Raw Water System

1. Clean out the sea water strainer, if necessary.
2. Make sure the sea-cock is open for generator set operation.
3. When a water/exhaust separator is provided, open the sea-cock for the water drain hose.
4. Check for hoses that leak or are damaged. Have a qualified service person replace any leaking or
damaged hoses.
3.2.7 Exhaust System

WARNING
Exhaust gas is deadly. Do not operate the generator set until all exhaust leaks have been
repaired.
1. Check that all CO monitors are working properly.

2. Inspect the exhaust system for leaks and loose hose clamps on:
• exhaust manifold
• exhaust elbow
• muffler
• water separator
• hull fittings
3. Replace any damaged sections of exhaust hose.

3.2.8 Mechanical System

1. Monitor generator set status using the digital display.
2. Visually check the generator set for mechanical damage.
3. For generator sets with sound shield, install service doors before running the generator set, then
listen for unusual noises when the generator set is running.
4. Check the generator set mounting bolts.
5. Check to see that the generator set air inlet and outlet openings are not clogged with debris or
blocked.
6. Keep the generator set compartment clean.
3.3 Maintaining the Battery

WARNING
Flames, sparks, or arcing at battery terminals, light switches, or other equipment can ignite
battery gas, causing severe personal injury. Ventilate the battery area before working on or near
a battery, wear safety glasses, and do not smoke. Turn work light on or off away from the battery.
When performing maintenance procedures or when servicing a battery, stop the generator set
and disconnect the charger before disconnecting battery cables. Using an insulated wrench,
disconnect the negative (–) cable first and reconnect it last.
Refer to Section 3.1 on page 21 for the battery maintenance schedule and follow the battery
manufacturer's instructions. Have the battery charging system serviced if DC system voltage is
consistently low or high.
Check the battery terminals for clean, tight connections. Loose or corroded connections have high
electrical resistance which makes starting harder.
1. Keep the battery case and terminals clean and dry.
2. Keep the battery terminals tight.
3. Remove battery cables with a battery terminal puller.
4. Make sure which terminal is positive (+) and which is negative (–) before making battery
connections, always removing the negative (–) cable first and reconnecting it last to reduce arcing.
3.4 Maintaining the Lubrication System

Keep dirt, water, and other contaminants from entering the lubrication system and corroding or clogging
lubrication components.
3.4.1 Oil Recommendations

CAUTION
Using normally specified CH-4 or equivalent oils will not allow a new or rebuilt engine to break-in
properly.
• Use API (American Petroleum Institute) Service Category CH-4 engine oil or better after the first 100
hours of engine break-in.

• Look for the SAE (Society of Automotive Engineers) viscosity grade. Choose the viscosity grade
appropriate for the ambient temperatures expected until the next scheduled oil change. See figure
below.
• Multi-grade oils such as SAE 15W-40 are recommended for year-round use.
3.4.1.1 Oil Viscosity vs. Ambient Temperature
FIGURE 7. OIL VISCOSITY VS. AMBIENT TEMPERATURE
3.4.2 Changing Engine Oil and Filter

WARNING
Accidental or remote starting can cause severe personal injury or death. Before removing a
panel or access door, or before working on the generator set, use an insulated wrench to
disconnect the negative (-) cable from the battery to prevent accidental starting.
WARNING
WARNING
State and federal agencies have determined that contact with used engine oil can cause cancer
or reproductive toxicity. Avoid skin contact and breathing of vapors. Use rubber gloves and
wash exposed skin.
Refer to Chapter 3 on page 21 for the engine oil change schedule.

1. Run the generator set under load until it is up to operating temperature, stop it, and disconnect the
negative (–) battery cable at the battery.
2. For generator sets with sound shield, remove service door.
3. Remove oil fill plug and open the drain valve. The drain valve has a 3/8 NPT outlet for connecting a
hose fitting to facilitate oil drainage.
WARNING
Crankcase pressure can blow hot engine oil out the fill opening causing, severe burns.
Always stop the generator set before removing the oil fill cap.
NOTICE
If an oil pump-out system is installed, follow the instructions provided with the pump.

NOTICE
Dispose of oil in accordance with local requirements.
4. Drain used oil into a suitable container.

5. Close the oil drain valve.
6. Remove the old oil filter or filters using a suitable filter wrench (available from Cummins Onan) and
appropriately discard the filter or filters.
7. Remove the old gasket if it does not come off with the filter. Wipe the sealing surface clean.
8. Apply a film of oil to the new filter gasket and partly fill the new filter with oil so that it reaches engine
parts sooner at startup.
9. Spin the filter on by hand until the gasket just touches the mounting pad and tighten 3/4 of a turn.
10. Refill the engine with the proper type and amount of engine oil. See previous section for oil
recommendations and Chapter 10 on page 111 for oil capacity.
CAUTION
Too little oil can cause severe engine damage. Too much oil can cause high oil
consumption. Keep the oil level between the high and low beads (or markings) on the
dipstick.
NOTICE
Do not fill the oil through the oil check port (where the dipstick is located) as oil will backup
in the tube.
11. Check the oil level and add or drain oil as necessary.
12. Reinstall service doors on generator sets that have a sound shield.
13. Reconnect the negative battery cable.
14. Run the generator for a few minutes, shut it down, and recheck for proper oil level and leaks.
15. Dispose of the used oil and oil filter in accordance with local environmental regulations.
3.5 Maintaining the Fuel System

Keep dirt, water, and other contaminants from entering the fuel system and corroding or clogging fuel
system components.
3.5.1 Fuel Recommendations

WARNING
Diesel fuel is combustible and can cause severe personal injury or death. Do not smoke near fuel
tanks or fuel-burning equipment or in areas sharing ventilation with such equipment. Keep
flames, sparks, pilot flames, electrical arcs and switches, and all other sources of ignition well
away. Keep a multiclass fire extinguisher handy.

High quality Grade 2-D diesel fuel is necessary for good performance and long engine life. Use Grade 1-D
diesel fuel where ambient temperatures are below 5° C (40° F). Where fuel is exposed to cold ambient
temperature, use fuel that has a cloud point (temperature at which wax crystals begin to form) at least 6°
C (10° F) degrees below the lowest expected fuel temperature.
• Diesel fuels specified by EN 590 or ASTM D975 are recommended.
• The Cetane number should not be less than 45 and sulfur content not more than 0.5% by weight.
• The specifications for the type and sulfur content (ppm, % weight) of the diesel fuel used must
comply with all emissions regulations applicable where the generator set is to be operated.
• Diesel fuel must meet the ASTM D975 standard for lubricity and pass a minimum load level of 3100
grams as measured by ASTM D6078, or maximum scar diameter of 0.45 mm as measured by
ASTM D6079 or ISO 12156-1.
• B5 bio-diesel fuel that meets industry specifications and quality is suitable for use with this generator
set.
3.5.2 Draining the Fuel Filter

The generator set may have a water-separator fuel filter. Check for other up-stream filters which may also
need to be drained or replaced. Drain water and sediment more often than scheduled if fuel quality is
poor, condensation cannot be avoided, or when a warning is being displayed for WATER IN FUEL.
Have towels and containers ready to clean, collect, and properly dispose of spilled or dripping fuel.
1. Using an insulated wrench, disconnect the negative (–) cable at the battery to prevent the engine
from starting.
2. Open the front access door.
3. Remove drain plug on bottom of filter to drain water and sediment into a suitable container, about
120 ml (1/2 cup).
4. Re-install drain plug.
5. Replace the front access door.
6. Connect negative (–) battery cable.
7. Dispose of the drain-off in accordance with local environmental regulations.
3.5.3 Replacing Fuel Filter

WARNING
WARNING

WARNING
See Section 3.1 on page 21 for scheduled fuel filter replacement. Replace the fuel filters if the engine
lacks power. The generator set may have a primary and a secondary fuel filter. The primary filter has a
water separator and sensor. Check for up-stream filters which may also need to be replaced.
1. Using an insulated wrench, disconnect the negative (–) cable at the battery to prevent the engine
from starting.
2. Open the front access door (if applicable).
3. Close any fuel supply and return valves.
4. Spin off the old filter with a filter wrench.
5. Dispose of old filter in accordance with local environmental regulations.
6. Clean the contact surface on the filter base, lubricate the new filter gasket, and hand tighten the new
filter.
7. Open any fuel supply and return valves.
8. Close the front access door, if applicable.
9. Prime the engine for at least 30 seconds to fill the new filter. Check for leaks as the generator set
runs for several minutes.
10. Retighten the filter by hand, if necessary.
11. Connect the negative (–) cable at the battery.
3.5.4 Priming the Fuel System

WARNING
WARNING
The fuel system should be primed after fuel filters are replaced or after the generator set runs out of fuel.
Push and hold STOP (prime) on the control switch or push and hold STOP (prime) on the digital
display for at least 30 seconds. The Generator status lamp will blink while priming and the status on the
digital display will change from Stopped to Priming.

3.6 Maintaining the Cooling System

The engine is cooled by a pressurized, closed-loop liquid system. Coolant is pumped through passages in
the engine block, head, and exhaust manifold. The exhaust manifold also serves as the engine coolant
reservoir.
Raw water (flotation water) is pumped through tubes in the heat exchanger to cool the engine coolant.
The raw water then passes through a hose into the exhaust-water mixer where it cools the exhaust gases
and is expelled.

3.6.1 Cooling System

Exhaust and Raw Water out to Bulkhead Fitting on
1 Coolant Flow 9
Right or Left Side
Exhaust-Water Mixer with High Temperature
2 Raw Water Flow 10
Exhaust Switch
Exhaust Manifold and Coolant Reservoir with
3 Coolant Drain Valve 11 Pressure Cap and Coolant Fill Neck. Fill neck has
hose barb for connecting coolant recovery tank.
4 Zinc Anode 12 Optional Low Coolant Level Sensor Location
5 Raw Water Drain Plug (both ends) 13 Coolant Thermostat
6 Heat Exchanger and Cleanout Covers (both ends) 14 Coolant Pump
7 Block Drain Valve 15 Raw Water Pump
Raw Water Hose to Exhaust-Water Mixer - when
Raw Water in from Bulkhead Fitting on Right or Left
8 required, replace with Siphon Break and Connecting 16
Side
Hoses
FIGURE 8. MDKBK, MDKBL, MDBKM, AND MDKBN


Raw Water to Pump from Bulkhead Fitting on Right
1 9 Coolant Temperature Sensor
or Left Side
2 Raw Water Pump 10 Coolant Thermostat Housing
Raw Water Hose to Exhaust-Water Mixer - When Location, Optional Low Coolant Sensor
3 required, replace with siphon break and connecting 11
hoses
Heat Exchanger with Zinc Anode and Clean Out Coolant Reservoir with Pressure Cap and Coolant
4 Covers (both ends) 12 Fill Neck - Fill Neck has Hose Barb for Connecting
Coolant Recovery Tank
Raw Water Cleanout Cover (Both Ends - Make Sure
5 Location, Block Drain Valve (Coolant) 13 to Reconnect Ground Strap on This End with Cover
Screw)
Exhaust and Raw Water Out to Bulkhead Fitting on
6 Coolant Drain Valve Raw Water Plugs (Underneath) 14
Right or Left Side
Exhaust-Water Mixer with High Temperature
7 Coolant Flow 15
Exhaust Switch
8 Coolant Pump Pulley
FIGURE 9. MDKBP, MDKBR, AND MDBKV


1 Hose, Thermostat to Coolant Reservoir 8 Raw Water Flow Switch
Heat Exchanger Mounting Straps (2) Torque to 11
2 Coolant Flow 9
Nm (8 ft-lb)
3 Hose, Heat Exchanger to Coolant Pump 10 Coolant Drain Valve
4 Hose, Coolant Reservoir to Heat Exchanger 11 Raw Water Drain Plug
Hose, Raw Water to Exhaust-Water Mixer - Replace
hose with siphon break and connecting hoses when
5 12 Heat Exchanger with Cleanout Covers (both ends)
required - For dry exhaust replace with hose to hull
fitting.
6 Raw Water Flow 13 Raw Water Pump
7 Zinc Anode 14 Hose, Raw Water Pump to Heat Exchanger
FIGURE 10. MDKBT AND MDKBU
3.6.4 Pressure Cap

WARNING
Hot Coolant
Hot coolant is under pressure and can spray, causing severe burns when loosening the pressure
cap or opening the coolant drain.
Let the engine cool before loosening the pressure cap. Wear safety glasses.
Replace the pressure cap every two years (seals deteriorate and leak). Proper cooling system pressure (7
psi) is essential for optimal engine cooling and minimal coolant loss.

3.6.5 Coolant Hoses

Check for and replace hoses that leak or are damaged.
Make sure the two hoses from the recovery tank are routed through the two holes in the right side of the
generator set enclosure (if applicable), that the coolant recovery hose is connected to the fill neck on the
engine, and that the overflow hose terminates in the drip pan where it will not splash coolant on electrical
components.
3.6.6 Siphon Break

WARNING
Bypassing a siphon break or failing to maintain it can lead to engine flooding and damage to the
engine that is not covered under warranty.
A siphon break is installed when the exhaust-water mixer is less than 6 inches above the water line.
Replace the siphon break if it is encrusted with deposits, which indicates leakage. If it is of the bleed-vent
type, check that the vent hose is connected to a through-hull fitting. Check for normal water flow whenever
the engine is running. See the Installation Manual for more information regarding siphon breaks.


1 Hose 4 Clamp-Hose
2 Valve-Check 5 Connector-Hose
3 Cap-Tube 6 Side Marked Vac (Black)
FIGURE 11. SIPHON BREAK
3.6.7 Coolant Recommendations

Use a high quality, fully formulated, ethylene glycol coolant with rust inhibitors and coolant stabilizers that
meets ASTM D6210 Standard Specification for Fully-Formulated Glycol Base Engine Coolant for Heavy-
Duty Engines. This will provide corrosion protection, foam control, liner-pitting protection, and
scale/deposit control.
Unless prohibited by shipping regulations, the generator set is shipped with the recommended 50/50
mixture of water and ethylene glycol which provides protection to -37° C (-34° F). In warmer climates and
sea water environments, a 60/40 mixture of water/ethylene glycol is recommended.
Use fresh water that is low in minerals and corrosive chemicals for the coolant mixture. Distilled water is
best.
See Chapter 10 on page 111 regarding coolant capacity.

WARNING
Ethylene glycol antifreeze is considered toxic. Dispose of it according to local regulations for
hazardous substances.
3.6.8 Replenishing Normal Coolant Loss

Check coolant level in the recovery tank before the first startup of each day and, if necessary, refill to
COLD when the engine is cold or to HOT when it is running. The recovery tank is designed to maintain
coolant level, not to fill the system. If the tank is empty, check for and repair any coolant leaks and refill
the system through the fill neck on the engine.
Make sure the two hoses from the recovery tank are routed through the two holes in the right end of the
generator set enclosure, that the coolant recovery hose is connected to the fill neck on the engine, and
that the overflow hose terminates in the drip pan where it will not splash coolant on electrical components.
3.6.9 Refilling Cooling System

CAUTION
Filling a hot engine with cold water can cause cracks in the manifold, head, and block. Follow the
manufacturer's instructions for cleaning and flushing.
See Section 3.6.7 on page 37 for coolant specifications. See Chapter 10 on page 111 for coolant
capacity.
1. Close the block and heat exchanger drain valves (or check to be sure they are closed), reconnect
the pump inlet hose (or check to be sure it is connected), and fill the system through the engine fill
neck. The system will fill only as fast as the air can escape. Fill to the bottom of the fill neck.
2. Start and run the engine for a couple of minutes to dislodge air pockets then shut it down.
3. Check the coolant level, add as much coolant as necessary, and secure the pressure cap.
4. Refill the recovery tank up to the COLD mark.
5. On sets with an enclosure, secure the top and front access doors, and use an insulated wrench to
reconnect the battery cables, negative [-] last, when done.
CAUTION
Low coolant level can cause severe engine damage. Be sure the system is full.
3.6.10 Draining and Cleaning Cooling System

WARNING
Hot Coolant

WARNING
1. Have towels and containers ready to clean, collect and properly dispose of the coolant.
2. Use an insulated wrench to disconnect the negative (-) cable at the battery to prevent the engine
from starting, let the engine cool, remove the front access door, top of the enclosure and coolant
pressure cap.
3. Remove the pressure cap.
4. Remove heat exchanger drain plug. Disconnect and drain lower hoses. Open block drain valve.
Drain the coolant into suitable containers for disposal in accordance with the local regulations for
hazardous substances.
5. Drain or flush a keel cooler in accordance with the manufacturer's instructions.
6. Use radiator cleaning chemicals to clean and flush the cooling system before refilling with fresh
coolant. Follow the cleaner manufacturer's instructions.
CAUTION
Filling a hot engine with cold water can cause cracks in the manifold, head, and block.
Follow the manufacturer's instructions for cleaning and flushing.
3.6.11 Heat Exchanger

WARNING
WARNING
WARNING
Ethylene glycol is considered toxic. Do not use it to protect the raw water passages in the heat
exchanger from freezing. It will be expelled into the environment when the generator set is
started.
See Section 3.1 on page 21 for scheduled maintenance. Clean the raw water tubes if the engine keeps
shutting down (Code No. 1) or the engine gauge or digital display indicates abnormally high engine
temperatures. Drain the heat exchanger if there is a danger of freezing when the generator set is not
running or is in storage. Freezing water can damage the raw water tubes in the heat exchanger. Engine
coolant is protected from freezing, water is not.

3.6.11.1 Heat Exchanger

1 Zinc Anode 3 Raw Water Drain Plug
2 Coolant Drain Valve 4 Clean Out Cover (both ends)
FIGURE 12. HEAT EXCHANGER
3.6.11.2 Removing and Installing the Heat Exchanger

Removal
1. Disconnect the four hoses. (To work the coolant hose elbow off the fitting on the heat exchanger, it
will be necessary to loosen the hose clamps on both ends.)
2. Remove the screw and mounting straps.
3. Remove the heat exchanger.
Installation
1. Reconnect hoses.
2. Place heat exchanger in mounting bracket.
3. Install mounting strap and secure with screw.
3.6.11.3 Draining and Cleaning the Heat Exchanger

1. Disconnect the negative (-) cable at the battery to prevent the engine from starting, let the engine
cool, and close the sea cock.
2. Remove the front access door, belt guard, top of the enclosure, and end panel, if so equipped.
3. Have towels and containers ready to prevent spilling raw water on the electrical components below
the heat exchanger.
4. Remove the water pump. This will make it easier to clean the tubes.

5. Remove the drain plug or clean-out cover.

6. Clean and flush the tubes. The drain plug must be removed to get all the water out of the tubes. Do
not use metal rods to clean the tubes. The tubes are made of relatively soft copper alloy and can be
easily damaged.
NOTICE
Have the heat exchanger cleaned at a radiator shop if there is hard scale in the tubes.
7. Use thread sealant on the drain plug and a new clean-out cover gasket if the old one is torn or
otherwise damaged.
8. Reassemble all the parts that were disassembled for access.
3.6.12 Zinc Anode

Replace the zinc anode as recommended in Chapter 3 on page 21. Use thread sealant on the zinc plug
and drain plugs and replace the clean-out cover gaskets if the old ones are torn or otherwise damaged.
See Section 3.6.11 on page 39 for location of zinc anode.
3.6.13 Replacing the Thermostat

WARNING
WARNING
Hot Coolant
See the Section 3.1 on page 21 section for scheduled replacement.

1. Use an insulated wrench to disconnect the negative battery cable at the battery to prevent the engine
from starting. Let the engine cool and remove the front access door.
2. Remove the pressure cap.
3. Drain the cooling system following procedure in previous section - Draining and Cleaning the Cooling
System.
4. Remove the two thermostat housing bolts and pull off the housing, thermostat, and gasket. The hose
does not need to come off.
5. Clean off the gasket area and install the new thermostat and gasket. Apply Three Bond 1215 liquid
sealant or equivalent to the top side of the gasket.
6. Replenish any lost coolant (refer to the previous section - Refilling the Cooling System), secure the
pressure cap, secure the top of the enclosure and access door, and reconnect the negative battery
cable.

FIGURE 13. TYPICAL THERMOSTAT AND HOUSING
3.6.14 Replacing Raw Water Pump Impeller

WARNING
WARNING
See Section 3.1 on page 21 for scheduled replacement. Avoid spilling raw water on the electrical
components below the pump. Have towels and containers ready in case of water spillage.
1. Close the sea-cock.
2. Disconnect the negative (-) cable at the battery to prevent the engine from starting.
3. Loosen the three screws on the end of the pump body to remove the pump body or impeller cover,
depending on construction (see below).
4. Remove the impeller and O-ring. An impeller removal tool may be necessary to pull the impeller off
the shaft.
5. Inspect impeller for broken vanes. Check for and clean out pieces that may have lodged in the heat
exchanger.
6. Install the new impeller - for easier installation, twist the impeller the way it normally turns on its own
while squeezing it into the housing.

7. To provide initial lubrication and better pump suction before water reaches the pump, wet the inside
of the pump and impeller with water, soap solution, or a silicone lubricant and secure the O-ring and
cover.
CAUTION
Do not lubricate with petroleum products like grease and oil which chemically attack
impeller materials.
8. Secure the cover or pump body and O-ring.

9. If the sea water strainer is above the water line, fill it for faster priming at startup.
10. Open the sea-cock, reconnect the negative battery cable and start the generator set. The generator
set will shut down within a few seconds if there is no raw water flow, and the amber status lamp will
blink shutdown Code No. 7. If it shuts down, remove any blockage and restart the generator set.


1 Cover 3 Impeller
2 O-Ring 4 Raw Water Pump
FIGURE 14. REPLACING THE RAW WATER PUMP IMPELLER
3.6.15 Adjusting V-Belt Tension

WARNING
1. Use an insulated wrench to disconnect the negative (–) cable at the battery to prevent the engine
from starting.
2. Remove the belt guard or enclosure top panel and access doors.
3. Loosen the alternator pivot bolt first and then the adjusting bracket bolt on top.

4. Pivot the alternator out to tighten belt tension. Hold tension by tightening the tension adjusting bolt
and then check tension by applying 10 kg (20 pounds) to the middle of the pulley span. Belt tension
is correct when deflection is 10 mm (3/8 inch).
5. Tighten the alternator bolts when tension is correct.
6. Tighten the bolts, secure the belt guard or enclosure and reconnect the negative battery cable.

1 Tension Adjusting Bolt 3 V-Belt
2 Alternator Pivot Bolt
FIGURE 15. ADJUSTING V-BELT TENSION
3.6.16 Replacing V-Belt When PTO Equipped

A special belt replacement kit must be used when the generator set is equipped with a PTO. The kit
includes a tool to keep the flexible coupling from twisting during assembly and disassembly. The coupling
has to be disassembled so that the belt can be looped around the crank pulley. Follow the instructions in
the kit.
3.7 Storing the Generator Set

When the generator set cannot be exercised regularly and (or) will be idle for more than 120 days, proper
storage is essential in preserving top performance and reliability.
1. Turn off the generator set line circuit breaker or AC distribution panel.
2. Change the engine oil and filter and attach a tag indicating oil viscosity.
3. Crank the engine several revolutions by pressing the start switch momentarily but do not let it start.
This will fill the oil passages with the new oil.
4. Use an insulated wrench to disconnect the battery cables, negative [-] cable first, from the starting
battery and store the battery according to the battery manufacturer's recommendations. Check
coolant level and add as necessary. Test the coolant mixture if freezing temperatures are possible
and change if necessary.

5. Drain the heat exchanger and muffler if freezing temperatures are expected.
6. Disengage the PTO clutch, if so equipped.
7. Clean and lightly oil parts that can rust.
3.8 Cold Temperature Storage

Freezing water can damage the heat exchanger and exhaust cooler. Drain these of any water before
freezing temperatures begin. See Section 3.7 on page 45.
3.9 Returning the Generator Set to Service

1. Check the oil tag on the generator set and change the oil if the viscosity indicated is not appropriate
for the temperatures expected.
2. Use an insulated wrench to reconnect the starting battery, negative [-] cable last.
3. Replace the raw water pump impeller if it is over one year old.
4. Service the air filter element if it is dirty.
5. Reinstall the serpentine belt if so equipped (see Service Manual).
6. Reinstall the PTO clutch, if so equipped.
7. Perform required maintenance.
8. After connecting the battery complete the pre-start checks and prime the fuel system.
9. Start and run the generator set.
10. Turn on the generator set line circuit breaker or distribution panel when ready to power loads.

4 Generator Set Control
4.1 Overview
WARNING
Accidental or remote starting of the generator set can cause severe personal injury or death.
Prevent accidental or remote starting by disconnecting the starting battery cables (negative [–]
first), using an insulated wrench and isolating all auxiliary supplies.
The control board has a microprocessor controller that provides all the control, monitoring, and diagnostic
functions required to operate the generator set.
Up to three Cummins Onan Digital Displays may be connected to the generator set for operator control
and monitoring.
An optional Network Interface Module (NIM) is available for mounting in the control box. It is equipped with
a connector for external SAE J1939 data link connections to an integrated boat monitoring system.
Refer to Appendix A on page 123 and Appendix C on page 143 for more information on control board
wiring and harnesses.
4.2 Controller
4.2.1 Major Functions of Generator Set Controller
4.2.1.1 Initialization
Control initialization consists of checking memory (RAM, ROM, EEPROM) and generator set configuration.
4.2.1.2 Fuel Prime

Press and hold the control switch at STOP (Prime) for more than 3 seconds to cause fuel pump (E5) to
prime the fuel system.
4.2.1.3 Start
Press and hold the control switch at START (Preheat) until the generator set starts. The controller:
1. Enables the status lamp (amber) to blink rapidly.
2. Enables some fault detection.
3. Energizes fuel lift pump (E5).
4. Energizes the glow plugs during pre-heat and cranking. The duration of pre-heat prior to cranking is
engine temperature dependent, but not to exceed 15 seconds.
5. Enables cranking. The maximum allowed duration of cranking is 20 to 60 seconds, depending on
engine temperature.
6. Enables field flash if no frequency pulses are present (F1-F2).
7. Energizes governor actuator (A12) (full rack).
8. Disconnects the starter (B1) at 800 RPM.

4. Generator Set Control 9-2016
9. When operating speed is reached:

a. Enables output voltage.
b. Turns off field flash.
c. Switches amber status lamp to green run lamp.
d. Enables Switched B+ (J7).
e. Enables complete fault detection.
4.2.1.4 Stop
Touch the control switch to STOP (Prime). The controller:
1. Disables output voltage.
2. De-energizes the fuel lift pump and governor actuator.
3. Turns off the status lamp.
4. Writes session data (number of cranks, minutes of operation, last fault, etc.) to non-volatile memory
(NVM).
5. Removes processor power when idle 5 minutes.
NOTICE
Stop takes precedence over Start if both are present due to a faulty switch or other cause.
4.2.1.5 Fuel Control

The controller positions the fuel rack to maintain nominal frequency as load varies by sending a pulse-
width-modulated (PWM) square-wave signal to governor actuator A12. It determines frequency by sensing
the frequency of the quadrature winding output. When the actuator is not energized, its spring-loaded
plunger holds the fuel rack in the no-fuel position.
4.2.1.6 Voltage Control

The controller maintains nominal AC output voltage during steady state operation by varying field current
as load varies. In response to transient loads it lowers the voltage set-point to allow engine recovery. Field
power (DC) is supplied by the quadrature windings (Q1-Q2) (AC) through the controller.
4.2.1.7 Voltage Adjustment

See Chapter 8 on page 95.
4.2.1.8 Adjusting Frequency

See Chapter 7 on page 91.
4.2.1.9 Fault Monitoring, Shutdown and Diagnostics

See the Troubleshooting Chapter of this manual (Chapter 9 on page 97).

9-2016 4. Generator Set Control
4.2.2 Control Block Diagram
FIGURE 16. CONTROL BLOCK DIAGRAM

4.2.3 Connectors
All connections to the controller are through connectors P1/J1 (black), P2/J2 (gray) and P3/J3 (green).
When removing a connector from the controller, squeeze the locking tabs on the sides while pulling out.
When reinstalling a plug, make sure the seal is in place and that the locking tabs snap into position.
CAUTION
Makeshift meter test probes used for testing control board connections during troubleshooting
can damage pin sockets by spreading or dislodging the contact wiper arms, resulting in an open
or intermittent electrical connection. Use a mating pin (Cummins Onan PN 323-1491) or a test
probe that is 0.045 inches in diameter. Replace damaged pin sockets (Cummins Onan PN 323-
1492). Make sure the pin sockets are fully seated and cannot be pulled out.
4.2.4 Removal/Replacement
WARNING
The control board is secured to the access cover by 2 screws. The cover is secured by 4 screws to the
enclosure end panel. Remove the 4 cover screws and withdraw the control board with the cover. To
remove the control board, first disconnect the 3 connectors (P1, P2 and P3) by squeezing the locking tabs
on the sides of the connectors while pulling out.
When reinstalling a connector plug, make sure the seal is in place and that the locking tabs snap into
position.

4.2.4.1 Generator Controller Mounting
FIGURE 17. GENERATOR CONTROLLER MOUNTING (ALL MODELS EXCEPT MDKBK)
4.2.4.2 Generator Controller Mounting
FIGURE 18. MDKBK CONTROLLER MOUNTING ILLUSTRATION

4.2.5 Configuring Generator Set Controller Using Digital Display

A replacement controller must be configured to the generator set configuration (1-phase or 3-phase). An
INVALID GENSET CONFIGURATION - CODE NO.37 shutdown will occur at startup if not configured
properly. Also, the digital display hour meter should be set to match the master hour meter.
Setting Configuration:
1. Stop the generator set and press STOP 6 times to display the configuration screen.
2. Press NEXT to select Genset Config.
3. Press the up-down arrows to select the configuration number marked on the generator set
nameplate, or see table below.
4. Press BACK to save the selection and get back to GEN STATUS.
Setting Digital Display Hour Meter:
1. Press NEXT to select Set Hour Meter.
2. Press the up-down arrows to match the number or hours on the master hour meter.
3. Press BACK to save the selection and get back to GEN STATUS.
FIGURE 19. CONFIGURING CONTROLLER AND SETTING HOUR METER
4.2.5.1 Generator Set Configuration Codes

TABLE 2. GENERATOR SET CONFIGURATION CODES
Generator Set Model Code Number

MDKBK — 1-phase 18
MDKBL — 1-phase 18
MDKBM — 1-phase 12
MDKBN — 1-phase 13
MDKBP — 1-phase 14
MDKBP — 3-phase 24
MDKBR — 1-phase 15
MDKBR — 3-phase 16
MDKBS — 1-phase 17
MDKBS — 3-phase 25
MDKBT — 1-phase 41
MDKBT — 3-phase 43

Generator Set Model Code Number

MDKBU — 1-phase 42
MDKBU — 3-phase 45
MDKBV — 1-phase 46
MDKBV — 3-phase 47
4.2.6 Configuring Generator Set Controller Using Control Switch

1. Remove the insulating connectors from wiring harness connectors CONFIG 1 and CONFIG 2 in the
control box and connect them together. This places the control in configuration mode. (In
configuration mode the control will not start, prime, or display faults.)
2. The status lamp on the control switch will blink the numeric configuration code, a two-digit number.
See above table for appropriate code number.
3. Press START or STOP to increase or decrease the code number. For example, the lamp should
blink as follows when configured for a 1-Phase, Model MDKDR generator set (15): blink — pause —
blink-blink-blink-blink-blink — long pause — repeat code
4. When configured properly, disconnect CONFIG 1 from CONFIG 2 and re-install the insulating
connectors that were removed from each connector.
4.3 Control Switch Schematic

The control switch, when located on the generator, is mounted on the control panel. Unsnap the connector
for access to its terminals. See Appendix A on page 123 for connections.
Referring to the figure below, replace the switch if:
• START does not close terminals 2 and 3,
• STOP does not close terminals 1 and 2,
• Green does not light when 12 VDC is applied across terminals 7 (–) and 8 (+),
• Amber does not light when 12 VDC is applied across terminals 7 (–) and 6 (+).
FIGURE 20. CONTROL SWITCH SCHEMATIC AND TERMINALS

4.4 Control Relays

To test a relay, apply 12 VDC (or 24 VDC if applicable) across terminals 85-86 (see figure below).
Replace the relay if 30-86 (NO) does not close or 30-87a (NC) does not open, or either does not return to
its normal position when power is removed.
See the drawings in Appendix A on page 123 for relay function.
FIGURE 21. CONTROL RELAY TERMINALS AND SCHEMATIC
4.5 Master Hour Meter (M11)

See Operator Manual for instructions on how to reset the hour meter on the digital display to match the
master hour meter when replacing the generator set controller.
4.5.1 Master Hour Meter (M11)
FIGURE 22. MASTER HOUR METER MOUNTED ON BRACKET

4.6 Emergency Stop Switch/Circuit Breaker

The switch/circuit breaker is mounted on the control panel. Disconnect the leads and check electrical
continuity across the two terminals. Replace the circuit breaker if it does not reset, turn on, or turn off. For
easier access to the switch terminals, push out the four plastic buttons that secure the panel and pull the
panel with switch forward.
4.7 DC Circuit Breaker

The switch/circuit breaker is mounted on the control panel. Disconnect the leads and check electrical
continuity across the two terminals. Replace the circuit breaker if it does not reset, turn on, or turn off. For
easier access to the switch terminals, push out the four plastic buttons that secure the panel and pull the
panel and switch forward.
4.8 Engine Oil Pressure Sensor (E1)

In isolated ground applications the sensor has two terminals. Use thread sealant and engage at least two
full threads when installing. Replace the sensor if resistance is not between 227 and 257 ohms when the
engine is stopped (0 psi). See Appendix A on page 123 for connections.
4.8.1 Oil Pressure Sensor (E1)
FIGURE 23. MDKBK, MDKBL, MDKBM, MDKBN

FIGURE 24. MDKBP, MDKBR, MDKBV
FIGURE 25. MDKBT, MDKBU
4.9 Coolant Temperature Sender (E2)

In isolated ground applications the sender has two terminals. Use thread sealant and engage at least two
full threads when installing. Replace the sender if resistance is not approximately 800 ohms at room
temperature or does not decrease rapidly when immersed in boiling water. See Appendix A on page 123
for connections.

4.9.1 Coolant Temperature Sender (E2)

4.10 High Exhaust Temperature Switch (S5)

The high exhaust temperature switch is provided on models with wet exhaust and is a normally-closed
switch. It is secured to the side of the water/exhaust mixer. See Appendix A on page 123 for
connections.
4.10.1 High Exhaust Temperature Switch (S5)

4.11 Raw Water Flow Switch (S6)

This switch is provided on models having a heat exchanger. The raw water flow switch is threaded into the
heat exchanger. It is a normally-closed switch. Use thread sealant and engage at least two full threads
when installing.

Check continuity across the switch terminals while blowing into it (1 psi). Replace the switch if it does not
open and close.
See Appendix A on page 123 for connections.
4.11.1 Raw Water Flow Switch (S6)

4.12 Low Coolant Level Switch (S3)

When provided, the low coolant level switch is threaded into the coolant reservoir. Use thread sealant and
engage at least two full threads when installing. See Appendix A on page 123 for connections.

4.12.1 Low Coolant Level Switch (S3)

4.13 Glow Plug Relay (K3)

The glow plug relay is mounted in its wiring socket inside the generator set control box.
To test the relay:
1. Remove the relay from the socket.
2. Apply battery voltage (12 VDC) across terminals 85-86.
3. Replace the relay if the contacts across terminals 30-87 do not close.
4.14 Starter Relay (K4)

The starter relay is mounted in its wiring socket on the controller mounting bracket.
To test the relay:
• Remove the relay from the socket.
• Apply battery voltage (12 VDC) across terminals 85-86.
• Replace the relay if the contacts across terminals 30-87 do not close.
4.15 Governor Actuator (A12)

The generator set controller modulates the pulse width of the current it sends to governor actuator (A12),
which positions the engine fuel rack accordingly.

If troubleshooting indicates that the actuator might be malfunctioning, disconnect its two leads and remove
the actuator. Replace the actuator if the plunger does not move smoothly when pushed in or the internal
spring does not return it smoothly. If the plunger moves smoothly without binding, apply battery voltage
(12 or 24 volts, depending on the generator set) and observe the plunger. Replace the actuator if the
plunger does not pull in all the way and stay in while power is applied.
Reinstall the actuator with a new flange gasket. Torque the two mounting screws to 9.5-12.2 Nm (7-9 ft-
lb).
4.15.1 Governor Actuator
FIGURE 38. MDKBK, MDKBL, MDKBM, MDKBN, MDKBT, MDKBU

4.15.2 Governor Actuator
4.16 Network Interface Module (NIM)

The optional NIM board has an open 12-pin connector socket for external network connections that mates
with a Deutsch® 12-pin sealed connector plug, part number DT06-12S. See illustration below for NIM
board mounting location.
See Appendix A on page 123 for connection information.
NOTICE
For more information on SAE 1939 applications see your Cummins Onan distributor. Cummins
Onan publication D-3315, Supported Messages on SAE J1939, must be used in designing the
interface for monitoring generator set status and diagnostics.
NOTICE
For more information on SmartCraft TM
applications see your Cummins MerCruiser Distributor.

4.16.1 NIM Mounting Location
FIGURE 40. NIM MOUNTING LOCATION
4.16.2 NIM Configuration Jumpers

The NIM board has 5 jumpers to configure the board for the specific application, as shown below.
1. Jumper W1 has no function at this time.
2. Jumper W2 will be cut when the generator set is ordered for an SAE J1939 or NMEA 2000TM network
application. The jumper must remain uncut when the generator set is ordered for a SmartCraftTM
network application.
3. Jumpers W3 and W4 are used to assign the network addresses of the generator sets in a multiple-
generator set installation. To assign an address, cut the jumpers as shown below.
TABLE 3. J1939 ADDRESSES
Jumper W3 Jumper W4 Address

Not Cut Not Cut 234
Not Cut Cut 158

Cut Not Cut 179

Cut Cut 203
4. Cut Jumper W5 if the bus termination resistor on this NIM board is not required to terminate the
network bus. (The jumper is cut on a SmartCraftTM board.)
FIGURE 41. NIM CONFIGURATION JUMPERS
4.16.3 Troubleshooting LEDs

1. The NIM must be awake to communicate. To wake up the NIM, press the start switch on the
generator set. The NIM will always be awake when the generator set is running. If there is no
communication activity, it will turn itself off in 5 to 10 minutes after the generator set stops.
2. LED indicator light DS2 blinks very fast when communicating with the generator set. If it does not,
check that the Y-harness is connected to 8-pin connector J10 on the NIM and generator set remote
connector J4 inside the control junction box. See Appendix A on page 123.
3. LED indicator light DS4 blinks approximately once a second when communicating with the network.
If it does not, check that the network harness is connected to 12-pin connector J11 on the NIM. If it
still does not communicate, troubleshoot the network harness.
4. LED indicator lights DS1 and DS3 are not used at this time.
4.16.4 Troubleshooting Network

1. Make sure the NIM has been configured properly with its jumpers.
2. Disconnect the network harness at 12-pin connector J11 on the NIM and measure resistance across
pins 4 and 5 in the mating network harness connector. The resistance should be 60 ohms, indicating
that there is a terminating resistor at each end of the network and that the wiring is intact.
3. Make sure that CAN HI (or CAN +) matches CAN HI on the display and rest of the network.
4.17 Electrostatic Discharge Control Bonding

To prevent electrostatic discharge from interfering with the generator set control, the control, generator,
and surrounding panels are bonded with braided wire straps or panel screws with toothed washers. Make
sure all bond straps and toothed washers are in place when reassembling components.


1 Main Bond Strap 3 Bond Strap Screws with Toothed Washers
2 Control Panel Bond Strap 4 Control Panel Bond Strap
FIGURE 42. ELECTROSTATIC DISCHARGE CONTROL BONDING

5 Engine and Accessories
5.1 Major Engine Service
WARNING
Refer to the Engine Workshop Manual for major engine service. See the Specifications Section (Chapter
10 on page 111) in this manual to identify the engine model number for the generator set.
When remounting the engine torque the vibration isolator through bolts to 37-44.7 Nm (27-33 ft-lb).
5.2 Exhaust Manifold

WARNING
panel or access door, disconnect the negative (-) cable at the battery to prevent the engine from
starting.
MDKBK, MDKBL, MDKBM, MDKBN: (Figure 43) When reassembling, use new manifold and mixer
gaskets. Torque the manifold nuts (2 per port) to 9.8-12.0 Nm (7.2-8.8 ft-lb) and the mixer flange bolts (4)
to 23.4-28.6 Nm (17.1-20.9 ft-lb).
MDKBT, MDKBU: (Figure 43) When reassembling, use new manifold and mixer gaskets. Torque the
manifold nuts (2 per port) and mixer flange bolts to 23.4-28.6 Nm (17.1-20.9 ft-lb).
MDKBP, MDKBR, MDKBV: (Figure 44) When reassembling, use new manifold and mixer gaskets. Torque
the manifold nuts (2 per port) and mixer or dry exhaust flange bolts (4) to 21-32 Nm (16-23 ft-lb). Torque
the wet exhaust hose adapter flange bolts (3) to 8.7-13.0 Nm (6.4-9.6 ft-lb).

5. Engine and Accessories 9-2016

1 Dry Exhaust Outlet 4 Exhaust Manifold/Coolant Reservoir
2 Temperature Switch 5 Short End of Exhaust Hose
3 Water-Exhaust Mixer
FIGURE 43. MDKBK, MDKBL, MDKBM, MDKBN, MDKBT, MDKBU

9-2016 5. Engine and Accessories

1 Dry Exhaust Assembly 3 Water-Exhaust Mixer
2 Wet Exhaust Assembly 4 Exhaust Manifold
5.3 Fuel System

WARNING
panel or access door, disconnect the negative (-) cable at the battery to prevent the engine from
starting.
WARNING
flames, sparks, pilot flames, electrical arcs and switches and all other sources of ignition well
away. Keep a multi-class fire extinguisher handy.
The figure below illustrates the fuel system and glow plug location.
See the Engine Workshop Manual for fuel injection system service.

5.3.1 Fuel System

1 Glow Plugs (3, 4, or 5) 4 Fuel Lift Pump
2 Fuel Return 5 Fuel Filter
3 Connect to bulkhead fitting, either end 6 Fuel Supply
FIGURE 45. TYPICAL FUEL SYSTEM
5.3.2 Fuel Filter

For fuel filter maintenance, see Section 3.5 on page 29.
5.3.3 Fuel Pump Test

A quick test to determine if the fuel pump is weak is to pinch the fuel bypass hose with rubber-tipped vise
grips. If an engine that fails to start, starts and runs with bypass flow cut off, fuel delivery to the engine is
weak. Service all fuel filters in the system and repair any restrictions to fuel flow. If fuel delivery is still
weak, test the fuel lift pump.

To test fuel lift pump delivery:

1. Disconnect the fuel return hose from the line to the supply tank and point the end into a container of
known volume, such as a 1 or 2 liter (quart) bottle.
2. Prime the generator set by pushing the Start/Stop switch to STOP (Prime) and hold it there for the
duration of the test. It should not take longer than 1-1/2 minutes to fill a 1 liter container (2/3 liter per
minute).
3. If flow is less than specified above, service all of the fuel filters in the system and repair any
restrictions to fuel flow. If fuel delivery is still weak, replace the fuel lift pump.
5.3.4 Fuel Pump Removal and Installation

Remove the right side panel for access.
Alternatively, if the starter has been removed from the front, the fuel pump can also be removed from the
front.
5.3.5 Fuel Fittings

The connections for fuel supply and return are pipe threaded fittings. Use liquid-type pipe thread sealant
listed as suitable for diesel fuel. Apply the sealant sparingly to the male threads only.
CAUTION
Excess liquid-type pipe thread sealant or pieces of Teflon-type pipe thread sealant can plug the
engine fuel system. Apply liquid-type pipe thread sealant sparingly to the male threads only. Do
not use Teflon tape.
5.3.6 Fuel Hose

Replace worn or damaged fuel hoses with USCG TYPE A1 or ISO 7840-A1 fuel hose. The hoses must be
long enough to be clamped and routed under the oil pan without rubbing on the oil pan.
If so equipped, the second intake resonator chamber must be removed to connect and disconnect the
supply hose at the fuel injector.
5.3.7 Glow Plugs

Refer to the Engine Workshop Manual when replacing the glow plugs. See Section 5.3 on page 71 for
glow plug location illustration.
NOTICE
If a glow plug does not come out after unscrewing it, or the end has broken off, it will be
necessary to remove the engine head. Glow plugs can swell if preheat voltage is greater than 14
volts, such as when a battery booster is used for starting.
Inspect the glow plugs as follows.

1. Check for B+ at the glow plug terminals during cranking. If there is no B+, remove the glow plug
relay K3 from its socket, test for proper operation (Section 4.13 on page 63), and replace if
necessary.
2. Check for B+ at relay socket terminal 30 for continuity between terminal 87 and the glow plugs, and
for continuity between terminal 86 and B- (ground).
3. Clean and tighten connections and replace wiring as necessary.

4. Check for B+ at relay socket terminal 85 while cranking. If there is no B+, disconnect connector P1
(black) from the generator set controller and check for a missing, bent or corroded Pin 1 and for
faulty wire and repair as necessary.
5. Remove the glow plug bus bar and check for electrical continuity between each glow plug terminal
and B- (ground).
6. Replace any open glow plug.
5.4 Starter
WARNING
The starter motor is bolted to the flywheel housing. For access, remove the right side enclosure panel.
See the Engine Workshop Manual for service or replacement. Parts are available for rebuilding the starter.
Torque the mounting bolts to 39 Nm (29 ft-lb).
5.4.1 Negative Ground Connection

1. Install the starter motor.
2. Check to sure that the engine block is grounded properly, depending on whether standard or isolated
ground connections are required.
3. Install the star washer between the engine block and cables.
4. Torque the bolt to 55 Nm (41 ft-lb).
5.4.2 Ground Isolation Relay (K9)

This relay is accessible after the starter or side panel has been removed.
When required, the generator set is equipped with isolation relay K9 to isolate the negative (-) battery
terminal from the vessel grounding system while the generator set is running. (The engine block is
connected to battery negative [-] during starting.) Replace the relay if its contacts do not close when 12
VDC voltage is applied to the coil terminals.

5.4.3 Starter Motor Mounting

1 Battery Charging Alternator 3 Starter Motor (other side on MDKDP, MDKDR,
MDKDV)
2 Relay K9
FIGURE 46. TYPICAL STARTER MOTOR, BATTERY CHARGING ALTERNATOR, AND B- ISOLATING RELAY
5.5 Raw Water Pump

The engine is equipped with a raw water pump only on models with wet exhaust or wet exhaust and heat
exchanger.
See Replacing the Raw Water Pump Impeller Section in the Maintenance Chapter for instructions on how
to replace the impeller. Kits are available for servicing the raw water pump. Follow the instructions in the
kit.
5.6 Battery Charging Alternator

See Adjusting V-belt Tension in the Maintenance Chapter to adjust or replace the alternator V-belt. See
the Engine Workshop Manual in the Related Literature Section of the Introduction Chapter for service or
replacement.


6 Alternator
6.1 Overview
WARNING
These are 4-pole, rotating-field, brushless, single-bearing generators. The figure below identifies the
typical generator components.
The engine rotates the generator field (main rotor) to induce output current (AC) in the main stator
windings. Generator output is proportional to the main rotor (field) current supplied by the exciter rotor
through its full-wave rectifier bridge (rotating rectifiers).
The generator set controller (Chapter 4 on page 47) rectifies and modulates quadrature winding output
(Q1, Q2) to supply the exciter stator (F1, F2). By comparing generator output voltage with a reference
value, the generator set control regulates field current to maintain nominal output voltage as load varies.
Also, in response to transient loads, it lowers the voltage setpoint to allow for engine recovery.
Residual field magnetism and a permanent magnet in one of the exciter stator poles initiates self-
excitation during startups.

6. Alternator 9-2016

1 Stator, Quadrature, Field, and Voltage Sensing 6 Exciter Rotor
Leads
2 Generator Stator (Main and Quadrature Windings) 7 Rotor Bearing
3 Exciter Stator 8 Main Rotor (Field)
4 Through Bolt (4) Torque Dry to 38–43 Nm (28–32 ft- 9 Disc Hub Bolt (6) Torque Dry to 50–57 Nm (37–42 ft-
lb) lb) Smooth, rounded sides of washers toward disc
5 End Bell Assembly 10 Disc Hub Bolt (6) Torque Dry to 27–31 Nm (20–23 ft-
lb) Smooth, rounded sides of washers toward disc
FIGURE 47. TYPICAL GENERATOR

9-2016 6. Alternator
6.1.1 Generator Stator and Winding Resistances

TABLE 4. GENERATOR STATOR AND WINDING RESISTANCES
Model Name Main Winding Quadrature Main Stator Exciter Rotor Exciter Stator
Resistance Winding Resistance Resistance Resistance
Ohms (1,2) Resistance Ohms (1) Ohms (1) Ohms (1)
Ohms (1)
4-Lead Generators (Single Phase)
MDKBP 0.078-0.086 0.807-0.897 2.32-2.56 0.58-0.71 13-16
MDKBR 0.055-0.061 0.658-0.728 2.77-3.06 0.58-0.71 13-16
MDKBS 0.025-0.028 0.483-0.533 2.97-3.27 0.58-0.71 13-16
MDKBT 0.029-0.032 0.506-0.560 2.57-2.87 0.58-0.71 13-16
MDKBU 0.025-0.028 0.483-0.533 2.97-3.27 0.58-0.71 13-16
MDKBV 0.055-0.061 0.658-0.728 1.89-2.32 0.58-0.71 13-16
12-Lead Generators (Three Phase)
MDKBP 0.172-0.191 2.347-2.594 2.54-3.10 0.58-0.71 13-16
MDKBR 0.105-0.117 1.853-2.048 2.17-2.65 0.58-0.71 13-16
MDKBS 0.054-0.068 0.80-0.91 2.77-3.06 0.58-0.71 13-16
MDKBT 0.056-0.062 0.865-0.956 2.32-2.56 0.58-0.71 13-16
MDKBU 0.054-0.068 0.80-0.91 2.77-3.06 0.58-0.71 13-16
MDKBV 0.105-0.117 1.853-2.048 2.20-2.68 0.58-0.71 13-16
1. If high, recheck winding resistance after the windings have cooled to room temperature.
2. The main windings are probably good if some of the resistances fall outside the range but are all within 10 percent
of each other.
6.2 Winding Insulation Resistance Test Procedure

A 500 VAC megger is recommended for the winding insulation resistance tests prescribed below. A test
consists of applying the test potential between the winding and ground (winding laminations) for a period
of 10 minutes and recording resistance at 1 minute and again at 10 minutes.
Resistance values of at least 5 megohms should be obtained for a new generator with dry windings. The
polarization index should also be at least 2 (the ratio of the resistance reading at ten minutes to the
reading at one minute). For a set that has been in service, the resistance reading should not be less than
1 megohm nor the polarization index less than 2.
Dry the windings if low readings are obtained or the set has been in standby for a long time in high
humidity conditions and repeat the test.
6.3 Winding Resistance Test Procedure

Use a digital ohmmeter or Wheatstone bridge to measure winding resistance. The device should have a
precision of at least 0.01 ohm.

6.4 Break-Out Tool 300-5512

Break-out tool, part of Tester Electronic UMC Service Kit 420-0624, for use in conjunction with an
accurate digital multi-meter, is available for performing winding output tests while running the generator
set. The tool is plugged into the generator set wiring harness in place of the generator set control. Follow
the tool instructions.
6.5 Exciter Stator

6.5.1 Winding Insulation Resistance
Test - Connect pin P3-7 or P3-6 to the megger and conduct the test as instructed under Winding
Insulation Resistance Test Procedure.
Disassembly - Disconnect generator set control connector P3.
6.5.2 Winding Resistance

Test - Measure winding resistance between pins P3-7 and P3-6.
Action - Replace the exciter stator if the resistance is not as specified in Table 4 on page 79.

6.5.3 Exciter Stator and End Bell

1 End Bell Casting Orientation: Leads - this side up. 3 Exciter Stator Leads F1 (P3-7) and F2 (P3-7)
2 Stator Mounting Screws Torque to 11 Nm (8 ft-lb) 4 Bearing Bore O-ring
FIGURE 48. EXCITER STATOR AND END BELL
6.6 Exciter Rotor

Test - Connect any lead to the megger and conduct the test as instructed under Winding Insulation
Resistance Test Procedure.
Disassembly - Disconnect all six exciter rotor leads from diode terminals CR1 through CR6 and isolate
them from ground.

Test - Measure electrical resistance across each pair of rotor windings: T11-T12, T21-T22, T12-T13, T22-
T23, T13-T11 and T23-T21. See the connection schematic.
Action - Replace the exciter rotor if the resistance of any winding is not as specified in Table 4 on page
79.

6.7 Rotating Rectifiers

The rotating rectifier assembly consists of two diode assemblies, one positive and one negative. Each
assembly contains the following:
• Three diodes
• Three terminals to connect to the appropriate lead of the exciter rotor (CR1, CR2, and CR3, or CR4,
CR5, and CR6)
• One field terminal (F1+ or F2-) to connect leads from the main rotor (generator field).
The rotating rectifier assembly is mounted on the back face of the exciter rotor.
Test
Use the diode test function on the test meter to test the six diodes in the rotating rectifier assembly. In the
forward bias direction the meter should indicate 0.5 to 0.8 volts. In reverse bias direction the meter should
indicate open.
1. Isolate Diodes - Disconnect the lead at each diode terminal (CR1, CR2, and CR3, or CR4, CR5, and
CR6) to make sure all of the meter test current flows only through the diode being tested.
2. Test Reverse Bias on Positive Rectifier - Touch meter positive to field terminal F1+ and meter
negative to diode terminals CR1, CR2, and CR3.
3. Test Forward Bias on Positive Rectifier - Touch meter negative to field terminal F1+ and meter
positive to diode terminals CR1, CR2, and CR3.
4. Test Reverse Bias on Negative Rectifier - Touch meter negative to field terminal F2- and meter
positive to diode terminals CR4, CR5, and CR6.
5. Test Forward Bias on Negative Rectifier - Touch meter positive to field terminal F2- and meter
negative to diode terminals CR4, CR5, and CR6.
Action
Replace the rectifier assembly if the meter indicates that any diode is open in both directions or is shorted
(zero ohms and/or audible signal).
1. Disconnect all leads from the defective diode assembly.
2. Remove the two mounting screws.
3. Make sure the replacement diode assembly is of the correct polarity, positive (+) or negative (–).
4. Attach the new diode assembly with two mounting screws.
5. Reconnect all leads.
6. Torque the terminal screws to 2.6 Nm (24 in-lb).
Assembly
Reconnect the lead at each diode terminal.
1. Reconnect the lead at each diode terminal.
2. Torque the terminal screws to 2.6 Nm (24 in-lb).


1 Diode Terminals (6) for Exciter Winding Lead. 4 Diode Assembly Mounting Screws (2)
Torque to 2.6 Nm (24 in-lb). Use flat washer to
protect lead connector.
2 Positive (+) Diode Assembly. Left-Hand Side, Shaft 5 Terminals F1+ and F2- for Main Rotor Leads.
Key Up. Torque to 2.6 Nm (24 in-lb)
3 Negative (–) Diode Assembly. Right-Hand Side, 6 Connection Schematic
Shaft Key Up.
FIGURE 49. ROTATING RECTIFIER ASSEMBLY
6.8 Main Rotor

Test - Connect either or both leads to the megger and conduct the test as instructed under Winding
Insulation Resistance Test Procedure.
Disassembly - Disconnect the main rotor leads from terminals F1+ and F2+ on the rotating rectifier
assemblies and isolate them from ground. Tag and mark each lead with its terminal number (F1+ or F2+).

CAUTION
Because of the opposing residual magnetism of the rotor, it might be difficult to re-establish self
excitation if the polarity of the main rotor leads is reversed upon reassembly.

Test - Measure electrical resistance between terminals F1+ and F2+.
Action - Replace the rotor if the resistance is not as specified in Table 4 on page 79.
Disassembly - Disconnect the main rotor leads from terminals F1+ and F2+ on the rotating rectifier
assemblies
Assembly - Reconnect the rotor leads and torque the terminals to 2.7 Nm (24 in-lb) when reassembling.

6.8.3 Rotor Assembly

1 Drive Disc Chamfered Edge Toward Flywheel 4 Rotor Bearing. Press on to shoulder. Do not
lubricate shaft.
2 Main Field 5 Exciter Rotor. Press on to shoulder. Do not lubricate
shaft.
3 Main Rotor Leads. Pass through exciter rotor to F1+ 6 Fan Blades
and F2- on rotating rectifiers. Disconnect leads when
testing main rotor. Torque nuts to 2.6 Nm (24 in-lb)
FIGURE 50. ROTOR ASSEMBLY
6.9 Main Stator

Test - Test each winding separately. Connect either or both winding leads to the megger and conduct the
test as instructed under Winding Insulation Resistance Test Procedure.
Disassembly - Disconnect the winding lead from its grounded neutral connection and isolate it. Leave the
other windings grounded.


Test -
• For 4-Lead generators measure resistance across lead pairs: T1-T2, T3-T4
• For 12-Lead generators measure resistance across lead pairs: T1-T4, T2-T5, T3-T6, T7-T10, T8-
T11, T9-T12
Action - Replace the stator assembly if the resistance of any winding is not as specified in Table 4 on
page 79.
Disassembly - Disconnect all main stator leads from the terminals to which they are connected.
6.9.3 Quadrature Winding Insulation Resistance

Disassembly
Disconnect generator set control connector P3.
Test
1. Connect a megger to connector P3 pin 4 or pin 5.
2. Do the Winding Insulation Resistance Test Procedure.
6.9.4 Quadrature Winding Resistance

Test
Use a Wheatstone bridge to measure winding resistance between pins P3-4 and P3-5.
Action
Replace the stator assembly if the resistance is not as specified in the Generator Stator and Winding
Resistances table in the beginning of the chapter.
6.9.5 Winding to Winding Insulation Resistance

Test
Check stator winding-to-winding insulation resistance between the following lead pairs as instructed under
Testing Winding Insulation Resistance:
4-Lead Generators 12-Lead Generators

From To From To From To
T1 T3 T1 T2 T3 T8
T2 P3-4 T1 T3 T3 T9
T3 P3-4 T1 T7 T7 T8
T1 T8 T7 T9
T1 T9 T8 T9
T2 T3 T1 P3-4
T2 T7 T2 P3-4
T2 T8 T3 P3-4

4-Lead Generators 12-Lead Generators

From To From To From To
T2 T9 T7 P3-4
T3 T7 T8 P3-4
T9 P3-4
Disassembly
Disconnect generator set control connector P3 and all main stator leads from the terminals to which they
are connected.
Assembly
Reconnect generator set control connector P3 and all main stator leads.
6.10 Generator Disassembly

WARNING
Accidental starting can cause severe personal injury or death. Disconnect the negative (–) cable
or cables at the battery or batteries to prevent the generator from starting.
WARNING
Accidentally dropping the generator can damage it and cause severe personal injury or death.
Use a hoist and straps of sufficient capacity and attach them so that the load cannot shift.
CAUTION
The generator drive plates will be damaged if the rotor is used to support the stator during
assembly or disassembly of the generatorThe generator drive plates will be damaged if the rotor
is used to support the stator during assembly or disassembly of the generator.
The generator is heavy. You will need a hoist of sufficient capacity.

1. Disconnect all power output connections, remote control connections, and conduit at the generator.
Label each lead clearly to make reconnections easier.
2. Disconnect all engine harness connections and grounding straps in the control box.
3. Disconnect all generator leads from connections in the output box.
4. Disconnect connectors P1, P2 and P3 from the generator set controller.
5. Disconnect connector P8 (some models) or disassemble the pins for generator leads Q1, Q2, F1,
F2, S1, S2 from connector P3.
6. Remove the control box, output box and saddle as an assembly.
7. Attach a hoist to the generator set lifting eye.
8. Remove the throughbolts in the two generator mounts.
9. Tip the generator end up slightly with the hoist.
10. Block the flywheel housing to support the engine while the generator is being serviced.
11. Cinch a strap around the middle of the generator stator and take up slack with the hoist.

12. On models with stator through bolts:

a. Scribe lines before separating the end bell from the stator and the stator from the flywheel
housing to register the parts for reassembly.
b. Remove the 4 nuts on the through bolts.
c. Tap the end bell free of the stator.
d. Tap the stator free of the flywheel housing.
e. Carefully draw the stator straight back until it clears the ends of the through bolts.
f. Remove the through bolts.
13. On models with flange bolts:
a. Remove the end bell and generator-to-engine flange bolts.
b. Carefully draw the stator straight back until it clears the end of the rotor.
14. Cinch a strap around the rotor.
15. Remove the 6 disc-to-flywheel bolts (Figure 47 on page 78).
16. Cradle the rotor horizontally in wooden blocks to prevent damage to windings, laminations, and drive
disc.
17. Use a gear puller to remove the rotor bearing or exciter rotor (Figure 47 on page 78).
6.11 Generator Reassembly

Reassembly is the reverse of disassembly. Note the following when reassembling the generator:
1. Press a new exciter rotor or rotor shaft bearing on up to its locating shoulder on the shaft. Do not
lubricate the shaft (Figure 47 on page 78).
2. Torque the 6 or 8 disc-to-hub bolts to 50-57 Nm (37-42 ft-lb). Make sure that:
• The chamfered edge on the drive disc perimeter faces out to make assembly with the flywheel
easier.
• The rounded edges of the washers are on the disc side.
3. Torque the 6 or 8 disc-to-flywheel bolts to 27-31 Nm (20-23 ft-lb). Make sure the rounded edges of
the washers are on the disc side.
4. On models with a generator-to-engine flange, torque the flange bolts to 50-60 Nm (37-45 ft-lb) and
the end bell flange bolts to 9 Nm (8 ft-lb)
5. On models with stator through bolts, use the 4 through bolts to help guide the stator on. Thread the
ends with less thread into the flywheel housing and make sure the threads bottom.
6. On models with stator through bolts, make sure the scribed stator-flywheel index lines register (Step
5 on page 87).
7. Torque the two exciter stator screws to 11 Nm (8 ft-lb). The pole to which the leads are tied must be
up.
8. Wipe the bearing bore in the end bell lightly with molybdenum disulfide grease and make sure the
rubber O-ring is in place.
9. On models with stator through bolts, assemble the end bell to the stator, making sure the scribed
index lines (Step 5 on page 87) register and the rotor bearing seats fully in the bore. Pull the field
leads out the same opening as the stator leads. Torque the nuts on the generator through bolts to
38-43 Nm (28-32 ft-lb).
10. Secure the end bell cover plate and torque the 4 screws to 3.8 Nm (8 in-lb).

11. Reassemble all the remaining components. Make sure to resecure the ring terminals of grounding
straps and leads with 2 star washers, one on each side, for good electrical continuity. Torque the
vibration isolator through bolts to 37-44.7 Nm (27-33 ft-lb).
6.12 Reconnecting the Generator

Reconnect the generator properly for the application. See Appendix A on page 123.
6.13 Line Circuit Breakers

WARNING
The line circuit breakers are mounted in the AC output box.

Test - Check electrical continuity across each pole.
Action - Replace a circuit breaker if either pole does not reset or turn ON and OFF.
Disassembly - Disconnect all leads
Assembly - Reconnect the generator and load wires properly (see Appendix A on page 123).


7 Changing Generator Set Frequency
7.1 As Manufactured
The generator set was set up and adjusted at the factory for the frequency and voltage stated in the As
Manufactured block on the nameplate (see figure below). If it is necessary to reconfigure voltage and (or)
frequency for the application, follow the instructions in this section.
7.2 Reconnection Label

The generator set manuals were shipped with a sheet with peel-off reconnection labels (Figure 52) to
apply over the As Manufactured block on the generator set nameplate (Figure 51) when reconfiguring the
generator set for the application. Apply the appropriate label if different from the As Manufactured data
block.
FIGURE 51. "AS MANUFACTURED" BLOCK ON NAMEPLATE

7. Changing Generator Set Frequency 9-2016
FIGURE 52. TYPICAL RECONNECTION LABELS
7.3 Changing Frequency

The DC side of the generator set control box has jumper leads marked HZ SEL and 60 HZ.
1. Remove the control box cover.
2. Connect HZ SEL and 60 HZ for 60 Hz output.
3. Disconnect HZ SEL and 60 HZ for 50 Hz output.
4. Apply the appropriate reconfiguration label.
5. Replace the control box cover.
NOTICE
When changing generator set operating frequency, make sure the line circuit breakers are
suitable for the new output. Replace them if necessary with ones of appropriate rating.
NOTICE
Check and adjust voltage as necessary after the frequency has been changed.

9-2016 7. Changing Generator Set Frequency
7.4 Reconnecting Generator

WARNING
If necessary:
1. Reconnect the generator for the application voltage in accordance with the appropriate generator
connection schematic (see Appendix A on page 123).
2. Apply the appropriate reconnection label.
3. Adjust voltage, if necessary.
NOTICE
It may be necessary to change circuit breakers to provide required protection or full
generator set power when reconnecting the generator.

7. Changing Generator Set Frequency 9-2016

8 Adjusting AC Output Voltage
8.1 Adjusting Voltage
Before adjusting voltage, make sure that proper fuel, exhaust, raw water, and battery connections have
been made and that the engine has the proper levels of oil and coolant.
Disconnect all generator loads and connect accurate meters to measure AC voltage and frequency.
NOTICE
When reconnecting the generator for a different output voltage, make sure the line circuit
breakers are suitable for the new output. Replace them if necessary with ones of appropriate
rating.
WARNING
Hazardous Voltage
Touching uninsulated live parts inside the generator set and connected equipment can result in
severe personal injury or death.
For your protection, stand on a dry wooden platform or rubber insulating mat, make sure your
clothing and shoes are dry, remove jewelry from your hands, and use tools with insulated
handles. Secure protective covers when completing installation.
8.2 Adjusting Voltage Using Digital Display

1. Start the generator set and let voltage and frequency stabilize for 5 to 10 seconds. Make sure all
loads have been disconnected.
2. Rapidly press START 6 times during the first minute after startup to put the generator set control into
voltage adjust mode. The green status lamp will blink rapidly and the display will indicate a status
change from Running to Volt Adj (see Voltage Adjustment Screen figure below).
3. To adjust voltage up, press and quickly release START. Voltage will increase approximately 0.6 volts
with each press and release.
4. To adjust voltage down, press and hold START for about 1 second. Voltage will decrease
approximately 0.6 volts with each press and release.
5. When satisfied with the adjustment, wait about 20 seconds for the display to indicate a status change
from Volt Adj to Running and then press STOP to stop the generator set and save the adjustment.
6. Restart the generator set and check voltage.
7. Recalibrate AC voltage on the digital display as instructed in the Operator Manual.

8. Adjusting AC Output Voltage 9-2016
FIGURE 53. VOLTAGE ADJUSTMENT SCREEN
8.3 Adjusting Voltage Using Control Switch

1. Start the generator set and let voltage and frequency stabilize for 5 to 10 seconds. Make sure all
loads have been disconnected.
2. Rapidly press START 6 times during the first minute after start up to put the generator set control
into voltage adjust mode. The amber status lamp will begin blinking about once every second to
indicate the change to voltage adjust mode. The green status lamp will remain on.
3. To adjust voltage up, press and quickly release START. Voltage will increase approximately 0.6 volts
with each press and release.
4. To adjust voltage down, press and hold START for about 1 second. Voltage will decrease
approximately 0.6 volts with each press and release.
5. When satisfied with the adjustment, wait about 20 seconds for the amber lamp to stop blinking and
then press STOP to stop the generator set and save the adjustment.
6. Restart the generator set and check voltage.

9 Troubleshooting
9.1 Overview
To troubleshoot the generator set, use the blinking control switch status lamp or the digital display fault
code in conjunction with the following list of fault codes (listed in order by fault code number). Perform the
step-by-step corrective actions suggested in this section.
NOTICE
Many generator set shutdowns can be avoided by performing periodic maintenance on schedule
and by not running the generator set out of fuel. Note that when generator sets and propulsion
engines draw from the same fuel tanks, the fuel pickup tubes are usually arranged so that the
generator sets run out of fuel first. By marking the generator set empty points on the fuel
gauges, it will be easier to tell when to stop the generator sets before running them out of fuel.
WARNING
Some generator set service procedures present hazards that can result in severe personal injury
or death. Only trained and experienced service personnel with knowledge of fuels, electricity,
and machinery hazards should perform generator set service. See the Safety Precautions chapter
for more information on hazards.
WARNING
9.2 Troubleshooting with Digital Display

If a fault shutdown occurs the ALARM status lamp on the Digital Display will blink and the LCD screen will
display the Fault Number, a description of the fault and the hour the fault occurred in total generator set
running time.
The fault will be displayed until it is cleared. Touch any button to clear the fault. The display will turn off in
5 minutes after the fault has been cleared.
See the Operator Manual for more information on displaying any of the last five faults.
9.3 Troubleshooting with Status Lamp

If a fault shutdown occurs, the amber status lamp on the control switch will repeatedly flash various sets of
blinks.
• A set of one blink indicates shutdown due to high engine temperature.
• A set of two blinks indicates shutdown due to low oil pressure.
• A set of three blinks indicates a service fault.
1. Press Stop once to cause the two-digit shutdown code to blink.

9. Troubleshooting 9-2016
The two-digit code consists of two sets of blinks. The first set is 1 to 7 blinks, which represents
the tens digit of the code number. There is a brief pause, then the second set of 1 to 9 blinks,
which represents the units digit of the code number. This is followed by a longer pause and
then repeats the process.
For example, Low Voltage Code No. 13 appears as: blink—pause—blink-blink-blink—long
pause—repeat
2. Pressing Stop again will stop the blinking.
• A set of four blinks indicates shutdown due to a failure to start within the time allowed for cranking.
• A set of five blinks indicates shutdown due to high levels of Carbon Monoxide (CO) in the vessel.
• A set of seven blinks indicates shutdown due to a loss of raw water flow for engine and exhaust
cooling.
Blinking continues for five minutes and stops. To restore blinking press the control switch to STOP
(Prime) until the lamp comes on (3 to 4 seconds). Then press STOP (Prime) three times to restore
blinking.
NOTICE
The last fault logged will blink even though the condition that caused the shutdown may have
been corrected.
9.4 Troubleshooting Generator Set Faults

WARNING
Some generator set service procedures present hazards that can result in severe personal injury
or death. Only trained and experienced service personnel with knowledge of fuels, electricity,
and machinery hazards should perform generator set service. See the Safety Precautions chapter
for more information on hazards.
WARNING
9.4.1 No Code - No Response at Digital Display or Control

Switch
Logic:
Faulty switch, poor or missing connections, dead battery
Diagnosis and Repair:
Refer to Appendix drawings as appropriate.
1. Push the Emergency Stop to remove the emergency stop and/or DC Circuit Breaker ON if tripped.
2. Try the local digital display or control switch on the generator set if there is no response at a remote
control switch, and vice versa. If at least one control switch or display works, but not the others, go to
Step 7.

9-2016 9. Troubleshooting
3. If no control switches work, service battery connections as necessary by cleaning and tightening,
recharging or replacing the battery, or replacing damaged battery cables.
4. If there still is no response, disconnect the mate to connector J4 (P4, P33, or P43) in the control box.
Check for battery voltage across pins J4-4 and J4-1 (B+, Display, Start/Stop, and ground). If there is
voltage, go to Step 7. If there is no voltage, go to Step 5.
5. Disconnect connector P2 (gray) from the generator set controller and check for battery voltage
across pin sockets P2-1 and P2-6. If there is voltage, replace the controller. If there is no voltage, go
to Step 6.
6. Test the Emergency Stop Breaker (CB1) and the DC Circuit Breaker (CB2) and replace if necessary.
If there still is no voltage, check for and repair faulty wiring and connectors between: P2-1 and CB2-
LOAD; CB2-LINE and CB1-LOAD; CB1-LINE and B1-BAT; and P2-6 and GND-ENG.
7. Test for and replace a faulty Display or control switch and repair faulty wiring and connectors. See
the Appendix for wiring connections.
9.4.2 No Code - Starter Engages and Disengages

Logic:
Low cranking voltage
1. De-energize the PTO clutch, if so equipped.
2. Service battery connections as necessary by cleaning and tightening, recharging or replacing the
battery, or replacing damaged battery cables (Section 3.3 on page 27).
3. Service the starter (Section 5.4 on page 74). For additional information, see the appropriate engine
Workshop Manual. See Chapter 5.
9.4.3 No Code - Starting Batteries do not Maintain a Charge

Logic:
Marginal battery, battery connections or charging system
1. Service battery connections as necessary by cleaning and tightening, recharging or replacing the
battery, or replacing damaged battery cables.
2. Check for and disconnect parasitic battery loads.
3. Service the battery starting alternator.
9.4.4 No Code - No AC Power When Generator Set is Running

Logic:
A Circuit Breaker is off, tripped or malfunctioning, or the generator is not connected properly.
1. Reset, turn on or repair the generator set circuit breaker if off or tripped.
2. Reset, turn on or repair any other circuit breaker in the AC power supply system if off or tripped.
3. If the generator set has a manual voltage regulator, push the manual voltage selector switch to auto.

9.4.5 Code No. 1 - High Engine Temperature

Logic: Engine coolant temperature is greater than 221° F (105° C) for three consecutive seconds. This
fault is not enabled until 60 seconds after start up.
1. Check for and clean a blocked sea water strainer. If above the water line, fill the strainer with water
to assist priming.
2. Check engine coolant level and add coolant as necessary.
3. Check for disconnected, kinked, or leaking hoses and reconnect, reroute, or replace.
4. Check for and readjust a loose pump belt.
5. Inspect the siphon break for proper operation.
6. Check for a worn raw water impeller and replace as necessary.
7. Clean the heat exchanger.
8. Check the bottom of the hull for any blockage at the through-hull fitting.
9. Drain and clean the coolant system to remove coolant passage fouling.
10. Replace the coolant thermostat, which might not be opening fully.
11. Check the ring terminal on coolant sender E2. Tighten if necessary.
12. Test coolant sender E2 and replace if necessary.
13. Disconnect connector P1 (black) from the generator set controller and check for electrical continuity
between Pin 9 and the ring terminal on sender E2. If it is an isolated-ground sender, also check for
electrical continuity between E2-2 and B- (ground). Repair wiring and connectors as necessary.
14. Replace the generator set controller.
9.4.6 Code No. 2 - Low Oil Pressure

Possible Cause:
Oil pressure is less than 69 kPa (10 PSI) for three consecutive seconds. This fault is not enabled until
three seconds after start up.
Corrective Action:
1. Check the engine oil level and add or drain oil as necessary. Repair any oil leaks.
2. If loose, tighten the ring terminal on oil pressure sender E1.
3. Check electrical resistance through sender E1. Replace the sender if resistance is not between 227
and 257 ohms (0 psi) when the engine is stopped.
4. Disconnect connector P1 (black) from the generator set controller and check for electrical continuity
between Pin 10 and the ring terminal on sender E1. If it is an isolated-ground sender, also check for
electrical continuity between E1-2 and B– (ground). Repair wiring and connectors as necessary.
5. Replace the sender with a gauge, ground the sender wire (to keep the engine running) and start the
engine. Shut down the engine immediately if there is no oil pressure. Service the engine lubricating
system in accordance with the Engine Workshop Manual if oil pressure is less than 98 kPa (14 PSI).
9.4.7 Code No. 3 - Service Check

Logic:

A fault with a 2-digit fault code number occurred.

Press the STOP switch once. The status lamp will blink the two-digit shutdown code which will be one of
the codes in this section. (Does not apply to Digital Display.)
9.4.8 Code No. 4 - Overcrank

Possible Cause:
Cranking time exceeded 20 to 60 seconds, depending on engine temperature.
1. Disconnect the PTO clutch, if so equipped.
2. Check fuel level and refill as necessary. (Note: The generator set fuel pickups are probably higher
than the propulsion engine fuel pickups.)
3. Open any closed fuel supply and return valves.
4. Prime the engine fuel system for at least 30 seconds.
5. Service as necessary by cleaning and tightening battery connections, recharging or replacing the
6. Remove combustion air or exhaust system blockages.
7. Check all fuel fittings for fuel and air leaks, tighten as necessary and reprime.
8. Replace fuel filters and reprime.
9. Check for contaminated fuel by connecting to a source of known fuel quality.
10. Change engine oil. Use oil of the proper viscosity for the ambient temperature. High oil viscosity can
slow cranking speed.
11. Conduct a fuel pump test and replace if necessary.
12. Inspect and service the glow plugs as follows:
a. If loose, tighten the glow plug terminals.
b. Check for B+ at the glow plug terminals during cranking. If there is no B+, remove glow plug
relay K3 from its socket in the control box, test for proper operation and replace if necessary.
Also check for B+ at relay socket terminal 30, for continuity between terminal 87 and the glow
plugs and for continuity between terminal 86 and B- (ground). Clean and tighten connections
and replace wiring as necessary.
c. Check for B+ at relay socket terminal 85 while cranking. If there is no B+, disconnect connector
P1 (black) from the generator set controller and check for a missing, bent or corroded pin (P1-
1) and faulty wire and repair as necessary. If the wire and connections are good, replace the
generator set controller.
d. Remove the glow plug bus bar and check for electrical continuity between each glow plug
terminal and B– (ground). Replace any open glow plug.
13. Check for proper operation of the governor actuator and replace if necessary.
14. Check compression and cylinder leak down and service a worn engine. See the Engine Workshop
Manual.
15. Service the fuel injectors. See the engine workshop manual.
16. Check for proper operation of the internal governor mechanism. See the Engine Workshop Manual.

9.4.9 Code No. 5 - Warning Shutdown due to CO

Logic:
Dangerous levels of Carbon Monoxide in Vessel.
Get everyone out into fresh air immediately and seek medical attention.
9.4.10 Code No. 7 - Loss of Raw Water Flow

Logic:
Low raw water pressure in heat exchanger
1. Open the sea cock.
2. Check for and clean a blocked sea water strainer. If above the water line, fill the strainer with water
to assist priming.
3. Check for disconnected, kinked, or leaking hoses and reconnect, reroute, or replace.
4. If loose, reconnect terminals S6+ and S6- to raw water flow switch S6.
5. Check for and readjust a loose pump belt.
6. Test raw water flow switch S6 and replace as necessary.
8. Check the bottom of the hull for any blockage at the through-hull fitting.
9. Disconnect connector P1 (black) from generator set controller and check continuity between Pin 8
and terminal S6+ and between terminal S6- and B- (ground). Repair wiring and connectors as
necessary.
9.4.11 Code No. 12 - High AC Voltage

Logic:
After voltage regulation was enabled output voltage jumped to more than 125% of rated for 75
milliseconds or to more than 115% of rated for 3 seconds
1. Check for a tripped generator set circuit breaker, reset if necessary, and run with fewer loads. (A
breaker tripping under load can cause generator set voltage to overshoot.)
2. Check all fuel fittings and filters for fuel and air leaks and tighten as necessary. (Air bubbles can
disrupt generator set frequency/voltage.)
3. Check the brushes and slip rings, and rotor and stator windings. Service as necessary.
5. Push the generator set line circuit breaker off, start the generator set, and measure output voltage. If
output voltage is normal, the problem is in the circuits external to the generator set. If there is no
voltage, test for grounded or shorted main, field or quadrature windings, and service as necessary.

9.4.12 Code No. 13 - Low AC Voltage

Logic:
After voltage regulation was enabled output voltage fell to less than 90% of rated for 5 seconds.
1. Push the generator set line circuit breaker to off and disconnect the PTO, if so equipped. If the
generator set now runs and voltage and frequency are normal, reduce the number of electrical and
mechanical (PTO) loads. If there is no voltage, test for grounded or shorted main, field or quadrature
windings, and service as necessary.
2. Check the fuel level and fill as necessary. (Note: The generator set fuel pickups are probably higher
than the propulsion engine fuel pickups).
disrupt generator set frequency/voltage.)
7. Conduct a fuel pump test and replace if necessary
9. Check the brushes and slip rings, rotor and stator windings, and service as necessary.
10. Check for proper operation of the governor actuator and service or replace as necessary.
11. Re-adjust high idle speed.
12. Service the fuel injectors in accordance with the Engine Workshop Manual.
13. Check fuel injection timing in accordance with the Engine Workshop Manual.
14. Check for proper operation of the internal governor mechanism in accordance with the engine
Workshop Manual.
15. Service a worn engine in accordance with the Engine Workshop Manual.
9.4.13 Code No. 14 - High AC Frequency

Logic:
After the starter was engaged frequency jumped to more than 70 Hz for 40 milliseconds or to more than
2% over nominal for 6 seconds.
1. Check for a tripped generator set circuit breaker, reset if necessary, and run with fewer loads. (A
breaker tripping under load can cause generator set frequency to overshoot.)
disrupt frequency).
Workshop Manual.

9.4.14 Code No. 15 - Low AC Frequency

Logic:
During normal operation Frequency fell to less than 90% of nominal for more than 8 seconds
1. Push the generator set line circuit breaker off and disconnect the PTO clutch, if so equipped. If the
generator set now runs, reduce the number of electrical and mechanical (PTO) loads, especially
those with high motor starting loads, such as air conditioners.
2. Check the fuel level and fill as necessary. (The generator set fuel pickups are probably higher than
the propulsion engine fuel pickups causing the generator to run out of fuel before the propulsion
engines).
5. Check all fuel fittings for fuel and air leaks and tighten as necessary. (Air bubbles can disrupt
frequency and voltage.)
9. Check for proper operation of the governor actuator and service or replace as necessary.
11. Service the fuel injectors in accordance with the engine Workshop Manual.
12. Check fuel injection timing in accordance with the engine Workshop Manual.
Workshop Manual.
14. Check compression and cylinder leak down. Service a worn engine in accordance with the engine
Workshop Manual.
15. Replace the generator set controller
9.4.15 Code No. 22 - Governor Overload

Logic:
Maximum allowable time at full-duty cycle was exceeded
1. Reduce the number of appliances running, especially those with high motor starting loads such as air
conditioners.
than the propulsion engine fuel pickups, causing the generator to run out of fuel before the
propulsion engine.)
5. Check all fittings and fuel filters for fuel and air leaks, tighten as necessary, and reprime.


12. Check fuel injection timing in accordance with the engine Workshop Manual.
Workshop Manual.
Workshop Manual.
15. Replace the generator set control.
9.4.16 Code No. 23 - Faulty Oil Pressure Sender

Logic:
Controller sensed grounded sender
1. If loose, tighten the ring terminal on oil pressure sender E1. (This fault will occur if a loose ring
terminal touches grounded metal.)
2. Repair wiring and connectors as necessary to eliminate the ground path.
3. Check electrical resistance through sender E1. Replace the sender if resistance is not between 227
and 257 ohms (0 PSI) when the engine is stopped.
9.4.17 Code No. 24 - Faulty Temperature Sender

Logic:
Controller sensed open sender
1. If loose, tighten the ring terminal on sender E2 . If it is an isolated-ground sender, also make sure
flag terminal is connected to terminal 2 on sender.
and ring terminal E2-1. If it is an isolated-ground sender, also check continuity between E2-2 and B–
(ground). Repair wiring and connectors as necessary.
3. Test sender E2 and replace as necessary.
9.4.18 Code No. 27 - Loss of AC Voltage Sense

Logic:
The generator set Controller lost VAC sensing during normal voltage regulation when the field was
functioning normally and frequency was at least 40 Hz
1. Disconnect connector P3 (green) from the generator set controller and check continuity between Pin
11 (S1) and Pin 12 (S2). If open, check for missing, bent or corroded pins and faulty wiring and
repair as necessary.

2. Test and service the generator as necessary.
9.4.19 Code No. 29 - High Battery Voltage

Logic:
During startup the generator set controller sensed that battery system voltage was greater than 19.2 volts
if 12 VDC system, or 32.2 volts if 24 volt system.
1. Check battery bank connections and reconnect if necessary for 12 volts or 24 volts, depending on
generator set model.
2. Select a lower battery booster charge rate (external charging system).
9.4.20 Code No. 32 - Starting Fault

Logic:
The generator set controller could not detect cranking speed [quadrature zero crossings] for 3 seconds.
1. Disconnect the PTO clutch, if so equipped.
2. Have the propulsion engines running while trying to start the generator set. Their charging alternators
may be able to maintain a high enough battery terminal voltage to start the generator set.
3. Service the battery as necessary by cleaning and tightening connections, recharging or replacing the
4. Change the engine oil to oil of the proper viscosity for the ambient temperature. (High oil viscosity
can slow cranking speed).
5. Check for proper operation of starter relay K4 and replace if necessary.
6. Disconnect connector P3 (green) from generator set controller and measure resistance between Pin
10 and K4-86 and between K4-85 and CB2-2. If either lead is open, check for a missing, bent, or
corroded pin or faulty wiring and repair as necessary.
7. Service the starter motor in accordance with the engine Workshop Manual.
8. Service the engine if the crankshaft is unusually hard to rotate manually, in accordance with the
engine Workshop Manual.
9.4.21 Code No. 35 - Control Card Failure - EE

Logic:
During startup the generator set controller detected an EE memory error.
Replace the generator set controller.
9.4.22 Code No. 36 - Unknown Shutdown

Logic:
The generator set controller declared this fault because engine speed fell below 1000 RPM for 0.5
seconds, though not by generator set or engine control action.


1. Check for mechanical damage and service as necessary.
2. Push the generator set line circuit breaker to off and disconnect the PTO clutch, if so equipped. If the
generator set now runs, reduce the number of electrical and mechanical (PTO) loads.
than the propulsion engine fuel pickups.)
6. Check all fuel fittings for fuel and air leaks, tighten as necessary.
9. Disconnect connector P1 (black) from the generator set controller and measure resistance between
Pin 5 and A12+ and between Pin 4 and A12–. If either lead is open, check for a missing, bent, or
corroded pin, or faulty wiring. Repair as necessary.
11. Service the brushes and slip rings as necessary and test the rotor and quadrature windings for
opens and shorts. Replace a stator or rotor found to have faulty windings.
12. Check for a malfunctioning exciter or rotor, or open or grounded quadrature circuit. Service as
necessary.
Workshop Manual.
Workshop Manual.
9.4.23 Code No. 37 - Invalid Generator Set Configuration

Logic:
The generator set controller is not configured properly for the generator set.
1. Make sure the ends of the two leads marked CONFIG 1 and CONFIG 2 in the control box are not
connected and that they are terminated with insulated connectors.
2. Reconfigure the generator set controller.
9.4.24 Code No. 38 - Field Overload

Logic:
High field voltage induced by high rotor temperature or low power factor loads.
1. Remove blockages to generator air flow at the front inlet air grill.
2. Reduce the number of appliances running at the same time, especially those with high motor starting
loads, such as air conditioners.

3. Have air conditioners and other appliances checked for proper operation. (A locked compressor rotor
can cause very low power factor.)
4. Check for loose generator fan and repair or replace as necessary.
5. Test and service the generator as necessary.
9.4.25 Code No. 41 - Generator Rotor Fault

Logic:
F+ grounded.
1. Disconnect connector P3 (green) from the generator set controller and check for continuity between
Pin P3-7 (F+) and B- (ground). Pin P3-7 should not be grounded. Repair or replace wiring, brushes,
slip rings, or rotor, as necessary.
9.4.26 Code No. 43 - Control Card Failure - RAM

Logic:
During startup the generator set Controller detected a RAM memory error
Replace the generator set controller.
9.4.27 Code No. 45 - Speed Sense Lost

Logic:
After start disconnect the generator set controller lost speed sense [quadrature zero crossings] for 0.25
seconds.
1. Disconnect connector P3 (green) from generator set controller and check for open or shorted field
(P3-6 to P3-7) and quadrature (P3-4 to P3-5) windings. Service generator as necessary.
9.4.28 Code No. 57 - Overprime

Logic:
A local or remote control switch was held in the prime position for more than 5 minutes.
1. Check for and remove any object that may be holding any control switch (local or remote) in the
prime position.
2. Replace any control switch (S4) in the control system that does not open across terminals 1 and 2
when Stop is released.
9.4.29 Code No. 58 - High Exhaust Temperature

Logic:

The temperature of the high exhaust temperature switch exceeds 82° C (180° F) which causes the switch,
which is normally closed, to open. The switch will close again when the temperature decreases to 71° C
(160° F). This fault could be due to a lack of water delivered to the exhaust/water mixer.
1. Check for disconnected, kinked, or leaking water hoses and reconnect, reroute, or replace.
2. Check for and clean a blocked sea water strainer. If strainer is above the water line, fill with water to
assist priming.
3. Inspect the siphon break (if provided) for proper operation.
4. If loose, reconnect terminals S5+ and S5- to high exhaust temperature switch S5.
6. Clean the heat exchanger.
and terminal S5+ and between terminal S5- and B- (ground). Repair wiring and connectors as
necessary.
8. Test high exhaust temperature switch S5 and replace as necessary.
9.4.30 Code No. 59 - Low Coolant Level

Logic:
The engine coolant level fell below the optional coolant level sensor
Add coolant as necessary and repair leaks.
9.4.31 Code No. 61 - External Shutdown

Logic:
The generator set was shut down by a fire suppression system or other external control.
Make all necessary repairs to the generator set and connected equipment. Reset the external control
which shut down the generator set.


10 Specifications
10.1 MDKBK, MDKBL, and MDKBM Specifications Table
TABLE 5. GENERATOR SET SPECIFICATIONS
DESCRIPTION MDKBK MDKBL MDKBM

Single-Bearing, 4-Pole Single-Bearing, 4-Pole Single-Bearing, 4-Pole
Alternator
Rotating Field, Brushless Rotating Field, Brushless Rotating Field, Brushless
Installation Drawing 0500-4753 0500-4752 0500-4754
Kubota 4-Stroke Cycle, Kubota 4-Stroke Cycle, Kubota 4-Stroke Cycle,
Indirect Injection, Water Indirect Injection, Water Indirect Injection, Water
Engine
Cooled Diesel with Digital Cooled Diesel with Digital Cooled Diesel with Digital
Electronic Governing Electronic Governing Electronic Governing
Model D1105 D1105 V1505
Rated RPM
60 Hz 1800 1800 1800
50 Hz 1500 1500 1500
Number of Cylinders 3 3 4
Bore 78 mm (3.07 in) 78 mm (3.07 in) 78 mm (3.07 in)
Stroke 78.4 mm (3.09 in) 78.4 mm (3.09 in) 78.4 mm (3.09 in)
Displacement 1.123 L (68.53 in3) 1.123 L (68.53 in3) 1.498 cm3 (91.41 in3)
FUEL:
BioDiesel Compatibility N/A N/A N/A
Consumption - 60 Hz
No Load 0.8 L/hr (0.2 gal/hr) 0.8 L/hr (0.2 gal/hr) 1.1 L/hr (0.3 gal/hr)
Half Load 1.9 L/hr (0.5 gal/hr) 1.9 L/hr (0.5 gal/hr) 2.6 L/hr (0.7 gal/hr)
Full Load 3.8 L/hr (1 gal/hr) 3.8 L/hr (1 gal/hr) 3.8 L/hr (1 gal/hr)
Consumption - 50 Hz
Full Load 3 L/hr (0.8 gal/hr) 3 L/hr (0.8 gal/hr) 3.4 L/hr (0.9 gal/hr)
Minimum Fuel Inlet
- 1.7 psi - 1.7 psi - 1.7 psi
Pressure
Minimum Fuel Inlet
Pressure with Auxiliary N/A N/A N/A
Pump
LUBRICATION:

10. Specifications 9-2016

Engine Oil Capacity 4 L (4.2 qt) 4 L (4.2 qt) 4.3 L (4.5 qt)
Maximum Angularity any
Direction
Continuous 10° 10° 10°
Intermittent 22.5° 22.5° 22.5°
COOLING:
Coolant Capacity 4 L (4.2 qt) 4 L (4.2 qt) 5 L (5.3 qt)
Coolant Flow Rate
60 Hz 18.9 L/min (5 gal/min) 18.9 L/min (5 gal/min) 18.9 L/min (5 gal/min)
50 Hz 15.9 L/min (4.2 gal/min) 15.9 L/min (4.2 gal/min) 15.9 L/min (4.2 gal/min)
Raw Water Flow Rate
Minimum Raw Water Inlet
- 1.7 psi - 1.7 psi - 1.7 psi
Pressure
Maximum Pressure Drop
across Keel Cooler Outlet 1 psi 1 psi 1 psi
and Inlet Connection
Heat Rejection to Coolant
307 Kcal/min (1220
60 Hz 239 Kcal/min (950 BTU/min) 239 Kcal/min (950 BTU/min)
BTU/min)
50 Hz 197 Kcal/min (780 BTU/min) 197 Kcal/min (780 BTU/min) 247 Kcal/min (980 BTU/min)
Thermostat Opening
71 °C (159.8 °F) 71 °C (159.8 °F) 71 °C (159.8 °F)
Temperature
Thermostat Fully Open
85 °C (185 °F) 85 °C (185 °F) 85 °C (185 °F)
Temperature
Recommended Pressure
48 kPA (7 psi) N/A 48 kPA (7 psi)
Cap
GENERATOR SET AIR
FLOW:
Combustion Air Flow 0.85 m3/min (30 ft3/min) 0.85 m3/min (30 ft3/min) 1.02 m3/min (36 ft3/min)
Heat Rejection to Ambient
60 Hz 50 Kcal/min (200 Btu/min) 50 Kcal/min (200 Btu/min) 58 Kcal/min (230 Btu/min)
EXHAUST:
Maximum Exhaust Back
3 in Hg 3 in Hg 3 in Hg
Pressure
Dry Exhaust Gas Flow 2.5 m3/min (90 ft3/min) 2.5 m3/min (90 ft3/min) 3.3 m3/min (118 ft3/min)

9-2016 10. Specifications

Dry Exhaust Temperature N/A
BATTERIES:
Nominal Battery Voltage 12/24 VDC 12/24 VDC 12/24 VDC
Minimum CCA Rating - SAE
360 Amps 360 Amps 500 Amps
@ 0 °C (32 °F) 12 VDC
12 Volt Net Battery
Charging Output
Negative Ground (60 Hz) 5 Amps 5 Amps 5 Amps
Isolated Ground (60 Hz) 5 Amps 5 Amps 5 Amps
24 Volt Net Battery
Charging Output
Isolated Ground (60 Hz) N/A N/A N/A
Isolated Ground (50 Hz) N/A N/A N/A
Starter Rolling Current
12V N/A N/A N/A
24V N/A N/A N/A
Maximum Starting Current
Resistance
12V N/A N/A N/A
24V N/A N/A N/A
SIZE, WEIGHT, NOISE:
Weight without Sound
Shield:
Dry Weight 252 kg (555 lb) 238 kg (525 lb) 290 kg (640 lb)
Weight with Sound
Shield:
Dry Weight 272 kg (600 lb) N/A 315 kg (695 lb)
Sound Level with Sound
66/65 dB(A) @ 60/50 Hz N/A 66/65 dB(A) @ 60/50 Hz
Shield @ 1 meter

10.2 MDKBN, MDKBP, and MDKBR Specifications Table

DESCRIPTION MDKBN MDKBP MDKBR

Alternator
Engine
Model V1505 V2003 V2403
Rated RPM
60 Hz 1800 1800 1800
50 Hz 1500 1500 1500
Stroke 78.4 mm (3.09 in) 92.4 mm (3.64 in) 102.4 mm (4.03 in)
Displacement 1.498 cm3 (91.41 in3) 1.999 L (121.99 in3) 2.434 cm3 (148.53 in3)
FUEL:
Consumption - 60 Hz
Half Load 2.6 L/hr (0.7 gal/hr) 3.4 L/hr (0.9 gal/hr) 3.8 L/hr (1 gal/hr)
Full Load 4.5 L/hr (1.2 gal/hr) 6.1 L/hr (1.6 gal/hr) 7.2 L/hr (1.9 gal/hr)
Consumption - 50 Hz
Full Load 3.8 L/hr (1 gal/hr) 4.9 L/hr (1.3 gal/hr) 6.4 L/hr (1.7 gal/hr)
Minimum Fuel Inlet
- 1.7 psi - 1.7 psi - 1.7 psi
Pressure
Minimum Fuel Inlet
Pump
LUBRICATION:
Engine Oil Capacity 4.3 L (4.5 qt) 7.6 L (8.0 qt) 7.6 L (8.0 qt)
Direction


COOLING:
Coolant Capacity 5 L (5.3 qt) 7.6 L (8.0 qt) 7.6 L (8.0 qt)
Coolant Flow Rate
60 Hz 18.9 L/min (5 gal/min) 53 L/min (14 gal/min) 53 L/min (14 gal/min)
50 Hz 15.9 L/min (4.2 gal/min) 37.9 L/min (10 gal/min) 37.9 L/min (10 gal/min)
Raw Water Flow Rate
- 1.7 psi - 1.7 psi - 1.7 psi
Pressure
358 Kcal/min (1420 402 Kcal/min (1590 500 Kcal/min (1980
60 Hz
BTU/min) BTU/min) BTU/min)
50 Hz
Thermostat Opening
71 °C (159.8 °F) 71 °C (159.8 °F) 71 °C (159.8 °F)
Temperature
Thermostat Fully Open
85 °C (185 °F) 85 °C (185 °F) 85 °C (185 °F)
Temperature
48 kPA (7 psi) 48 kPA (7 psi) 48 kPA (7 psi)
Cap
GENERATOR SET AIR
FLOW:
Combustion Air Flow 1.16 m3/min (41 ft3/min) 1.45 m3/min (52 ft3/min) 1.72 m3/min (60 ft3/min)
EXHAUST:
Pressure
Dry Exhaust Temperature
BATTERIES:


@ 0 °C (32 °F) 12 VDC
12 Volt Net Battery
Charging Output
24 Volt Net Battery
Charging Output
Isolated Ground (60 Hz) N/A 28 Amps 28 Amps
Isolated Ground (50 Hz) N/A 24 Amps 24 Amps
12V N/A N/A N/A
24V N/A N/A N/A
Resistance
12V N/A N/A N/A
24V N/A N/A N/A
Shield:
Weight with Sound
Shield:
66/65 dB(A) @ 60/50 Hz 67/64 dB(A) @ 60/50 Hz 67/64 dB(A) @ 60/50 Hz
Shield @ 1 meter

10.3 MDKBT, MDKBU, and MDKBV Specifications Table

DESCRIPTION MDKBT MDKBU MDKBV

Alternator
Engine
Model V3300 V3300 V2403
Rated RPM
60 Hz 1800 1800 1800
50 Hz 1500 1500 1500
Stroke 110 mm (4.33 in) 110 mm (4.33 in) 102.4 mm (4.03 in)
Displacement 3.318 L (202.48 in3) 3.318 L (202.48 in3) 2.434 cm3 (148.53 in3)
FUEL:
Consumption - 60 Hz
Full Load 9.1 L/hr (2.4 gal/hr) 11.4 L/hr (3 gal/hr) 7.6 L/hr (2 gal/hr)
Consumption - 50 Hz
Half Load 4.2 L/hr (1.1 gal/hr) 4.5 L/hr (1.2 gal/hr) 3.8 L/hr (1 gal/hr)
Full Load 6.8 L/hr (1.8 gal/hr) 9.1 L/hr (2.4 gal/hr) 6.4 L/hr (1.7 gal/hr)
Minimum Fuel Inlet
- 1.7 psi - 1.7 psi - 1.7 psi
Pressure
Minimum Fuel Inlet
Pump
LUBRICATION:
Engine Oil Capacity 10.4 L (11 qt) 10.4 L (11 qt) 7.6 L (8.0 qt)
Direction


COOLING:
Coolant Capacity 14 L (14.5 qt) 14 L (14.5 qt) 7.6 L (8.0 qt)
Coolant Flow Rate
60 Hz 53 L/min (14 gal/min) 53 L/min (14 gal/min) 53 L/min (14 gal/min)
50 Hz 43.5 L/min (11.5 gal/min) 43.5 L/min (11.5 gal/min) 37.9 L/min (10 gal/min)
Raw Water Flow Rate
60 Hz 59.1 L/min (15.6 gal/min) 59.1 L/min (15.6 gal/min) 34.1 L/min (9 gal/min
- 1.7 psi - 1.7 psi - 1.7 psi
Pressure
60 Hz
50 Hz
Thermostat Opening
76.5 °C (170 °F) 76.5 °C (170 °F) 71 °C (159.8 °F)
Temperature
Thermostat Fully Open 90 °C (194 °F)
90 °C (194 °F) 85 °C (185 °F)
Temperature
48 kPA (7 psi) 48 kPA (7 psi) 48 kPA (7 psi)
Cap
GENERATOR SET AIR
FLOW:
Combustion Air Flow 2.6 m3/min (91.7 ft3/min) 2.6 m3/min (91.7 ft3/min) 1.72 m3/min (60 ft3/min)
EXHAUST:
Pressure
Dry Exhaust Temperature 475 °C (887 °F) 475 °C (887 °F)
BATTERIES:


@ 0 °C (32 °F) 12 VDC
12 Volt Net Battery
Charging Output
24 Volt Net Battery
Charging Output
12V N/A N/A N/A
24V N/A N/A N/A
Resistance
12V N/A N/A N/A
24V N/A N/A N/A
Shield:
Weight with Sound
Shield:
68/67 dB(A) @ 60/50 Hz 68/67 dB(A) @ 60/50 Hz 67/64 dB(A) @ 60/50 Hz
Shield @ 1 meter


11 Maintenance Record
TABLE 8. MAINTENANCE RECORD
Record all periodic and unscheduled maintenance/service. See Periodic Maintenance section.
HOUR
DATE METER MAINTENANCE OR SERVICE PERFORMED
READING
Record the name, address, and phone number of your authorized Cummins Onan service center.

11. Maintenance Record 9-2016

Appendix A. Wiring Diagrams
Table of Contents
Figure 54. A049H027 Sheet 1 .................................................................................................................... 125
Figure 55. A049H027 Sheet 2 .................................................................................................................... 126
Figure 56. A049H027 Sheet 3 .................................................................................................................... 127

Appendix A. Wiring Diagrams 9-2016
The drawings included in this section are representative. For current complete information,
refer to the drawing package that was shipped with the unit.

9-2016 Appendix A. Wiring Diagrams
A.1 Wiring Drawing
FIGURE 54. A049H027 SHEET 1


9-2016 Appendix A. Wiring Diagrams


Appendix B. Outline Drawings
Table of Contents
Figure 57. MDKBK Outline Drawing (Sheet 1) ......................................................................................... 131
Figure 58. MDKBK Outline Drawing (Sheet 2) ......................................................................................... 132
Figure 59. MDKBL Outline Drawing (Sheet 1) ......................................................................................... 133
Figure 60. MDKBL Outline Drawing (Sheet 2) ......................................................................................... 134
Figure 61. MDKBM and MDKBN Outline Drawing (Sheet 1) .................................................................. 135
Figure 62. MDKBM and MDKBN Outline Drawing (Sheet 2) .................................................................. 136
Figure 63. MDKBP, MDKBR, and MDKBV Outline Drawing (Sheet 1) ................................................... 137
Figure 66. MDKBT and MDKBU Outline Drawing (Sheet 1) ................................................................... 140
Figure 67. MDKBT and MDKBU Outline Drawing (Sheet 2) ................................................................... 141

Appendix B. Outline Drawings 9-2016

9-2016 Appendix B. Outline Drawings
B.1 MDKBK Outline Drawing
FIGURE 57. MDKBK OUTLINE DRAWING (SHEET 1)

FIGURE 58. MDKBK OUTLINE DRAWING (SHEET 2)

B.2 MDKBL Outline Drawing
FIGURE 59. MDKBL OUTLINE DRAWING (SHEET 1)

FIGURE 60. MDKBL OUTLINE DRAWING (SHEET 2)

B.3 MDKBM and MDKBN Outline Drawing
FIGURE 61. MDKBM AND MDKBN OUTLINE DRAWING (SHEET 1)

FIGURE 62. MDKBM AND MDKBN OUTLINE DRAWING (SHEET 2)

B.4 MDKBP, MDKBR, and MDKBV Outline Drawing
FIGURE 63. MDKBP, MDKBR, AND MDKBV OUTLINE DRAWING (SHEET 1)



B.5 MDKBT and MDKBU Outline Drawing
FIGURE 66. MDKBT AND MDKBU OUTLINE DRAWING (SHEET 1)

FIGURE 67. MDKBT AND MDKBU OUTLINE DRAWING (SHEET 2)


Appendix C. Wiring Harnesses
Table of Contents
Figure 68. 338-4412 Wiring Harness ........................................................................................................ 145

Appendix C. Wiring Harnesses 9-2016

9-2016 Appendix C. Wiring Harnesses
C.1 MDK Wiring Harness
FIGURE 68. 338-4412 WIRING HARNESS

Appendix C. Wiring Harnesses 9-2016

power.cummins.com
Copyright © 2016 Cummins Inc. All rights reserved.
Cummins, Onan, the "C" logo, and "Performance you rely on." are trademarks of Cummins Inc.
Other company, product, or service names may be trademarks or service marks of others.
Specifications are subject to change without notice.

MDKBK BL BM BN BP BR Bs BT Bu BV Service Manual

Uploaded by

Copyright:

Available Formats

MDKBK BL BM BN BP BR Bs BT Bu BV Service Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MDKBK BL BM BN BP BR Bs BT Bu BV Service Manual

Uploaded by

Copyright:

Available Formats

Service Manual

Marine Generator Set

MDKBK (Spec A-G)

981-0543 (Issue 15) i Copyright © 2016 Cummins Inc.

3.2.6 Raw Water System .................................................................................................... 26

4. GENERATOR SET CONTROL.................................................................................................... 47

Copyright © 2016 Cummins Inc. ii 981-0543 (Issue 15)

4.6 Emergency Stop Switch/Circuit Breaker............................................................................... 55

5. ENGINE AND ACCESSORIES.................................................................................................... 69

981-0543 (Issue 15) iii Copyright © 2016 Cummins Inc.

5.4.1 Negative Ground Connection..................................................................................... 74

7. CHANGING GENERATOR SET FREQUENCY .......................................................................... 91

8. ADJUSTING AC OUTPUT VOLTAGE ......................................................................................... 95

Copyright © 2016 Cummins Inc. iv 981-0543 (Issue 15)

9.1 Overview ............................................................................................................................... 97

10. SPECIFICATIONS .................................................................................................................... 111

11. MAINTENANCE RECORD ....................................................................................................... 121

APPENDIX A. WIRING DIAGRAMS ............................................................................................... 123

APPENDIX B. OUTLINE DRAWINGS ............................................................................................ 129

981-0543 (Issue 15) v Copyright © 2016 Cummins Inc.

B.1 MDKBK Outline Drawing .................................................................................................... 131

APPENDIX C. WIRING HARNESSES............................................................................................ 143

Copyright © 2016 Cummins Inc. vi 981-0543 (Issue 15)

1.2 Precaution Symbols

981-0543 (Issue 15) 1 Copyright © 2016 Cummins Inc.

1.3 General Safety Precautions

Copyright © 2016 Cummins Inc. 2 981-0543 (Issue 15)

981-0543 (Issue 15) 3 Copyright © 2016 Cummins Inc.

1.4 Electrical Shocks and Arc Flashes Can Cause

Guidelines to follow when working on de-energized electrical systems:

Copyright © 2016 Cummins Inc. 4 981-0543 (Issue 15)

1.5 Generator Voltage Is Deadly

1.6 Engine Exhaust Is Deadly

981-0543 (Issue 15) 5 Copyright © 2016 Cummins Inc.

1.7 Diesel Fuel is Combustible

1.8 Battery Gas is Explosive

1.9 Moving Parts Can Cause Severe Personal Injury Or

1.10 Flammable Vapor Can Cause a Diesel Engine to

1.11 Hazards of Carbon Monoxide

Copyright © 2016 Cummins Inc. 6 981-0543 (Issue 15)

1.11.1 Carbon Monoxide Poisoning

1.11.2 Special Risks of CO on Boats

981-0543 (Issue 15) 7 Copyright © 2016 Cummins Inc.

FIGURE 1. STATION WAGON EFFECT

1.11.3 Protection From CO Poisoning

1.12 Substances Hazardous to Health

1.12.1 Antifreeze (Fleetguard - ES Compleat and EG Premix)

Copyright © 2016 Cummins Inc. 8 981-0543 (Issue 15)

1.12.1.1 Hazardous Reactions

1.12.1.2 Protective Measures

1.12.1.3 Storage and Transport

1.12.1.4 Emergency Action

981-0543 (Issue 15) 9 Copyright © 2016 Cummins Inc.

1.12.2 Gas Oil

1.12.2.1 Hazardous Reactions

1.12.2.2 Protective Measures

1.12.2.3 Storage and Transport

Copyright © 2016 Cummins Inc. 10 981-0543 (Issue 15)

1.12.2.4 Emergency Action